ROI-S05934-051E 060406

P ASOLINK

N ETWORK

M ANAGEMENT

S YSTEM

PNMS (Java version)Installation Manual

(WindowsXP)

NEC Corporation Copyright © 2006

ROI-S05934

- i -

Table of Contents

1. Installation Sequence ....................................................................................................1

2. LAN Setting .................................................................................................................2

3. Setting Phone and Modem Options ...........................................................................5

4. Dial-up Setting .........................................................................................................10

5. SNMP Service Setting..............................................................................................19

6. PNMS Setup...............................................................................................................24

7. Launching PNMS .......................................................................................................29

ROI-S05934

- 1 -

1. Installation Sequence

Step 2: SNMP service setting(s)

Step 3: Pasolink Network Management System (PNMS) setup

Step 4: Launching PNMS

Step 1: Ethernet option LAN setting(s)

Step 1 Dial-up option 1-1 Phone and modem setting(s) 1-2 Dial-up setting(s)

ROI-S05934

- 2 -

2. LAN Setting

(1) In the Network Connections window, right-click [Local Area Connection] and select [Properties] for the desired Internet mode: LAN or High-Speed Internet or Dial-up

(2) Verify that Internet Protocol (TCP/IP) is checked in the Local Area Connection Properties

window. Click [Properties].

ROI-S05934

- 3 -

(3) Verify that Use the following IP address is selected and input the IP address, Subnet mask, and Default gateway assigned to the PNMS PC. Click [Advanced].

(4) Verify that the values input in (3) above are displayed on the IP Settings tab.

ROI-S05934

- 4 -

(5) Retaining the default setting on the Authentication tab, click the Advanced tab.

(6) Retaining the default setting on the Advanced tab, click [OK]

Before activating Windows XP SP2 After activating Windows XP SP2

ROI-S05934

- 5 -

3. Setting Phone and Modem Options

(1) Click on Start Settings Control Panel on the Windows XP™ start tab.

(2) Click on Phone and Modem Options icon to start configuring the modem.

ROI-S05934

- 6 -

(3) Select country and input area code on Location Information. Click on OK button to continue.

(4) Verify Location and Area Code.

ROI-S05934

- 7 -

(5) Select Modem tab, click on Add button to continue adding the new modem.

(6) Check Don’t detect my modem box and click on Next button to continue.

ROI-S05934

- 8 -

(7) Select Standard Modem Types and Standard 19200 Modem from Manufacturer and Models list respectively. Click on Next button to continue.

(8) Select Selected ports and COM1, then click on Next button to continue. If you are using multi-port configuration, select All ports to install the standard 19200 bps modem driver to all available COM ports.

ROI-S05934

- 9 -

(9) Click on Finish button to finalize the new modem installation.

(10) Verify that COM1 Standard 19200 bps Modem is displayed on the list. Click on OK button.

ROI-S05934

- 10 -

4. Dial-up Setting

(1) Click on Start Settings Control Panel Network Connections icon to start configuring the Dialup setting.

(2) Network Connections is displayed. Click the Create a new connection in Network Tasks category. Dial-up setting is written in this Section 3. If you connect PNMS to equipment with LAN connection, please jump to Section 4.

ROI-S05934

- 11 -

(3) Click on Next button on the next message box.

(4) Check on Connect to the network at my workplace and click on Next button to continue.

ROI-S05934

- 12 -

(5) Check on Dial-up connection and click on Next button to continue.

(6) In the Network Connection Wizard window, type in Pnms001 on the allocated box. Click on Next button to continue.

ROI-S05934

- 13 -

(7) Enter any number in the Phone number box. Click on Next button to continue.

(8) Verify that the connection Pnms001 is registered. You can also create a shortcut on your desktop if you wish. Click on Finish button.

ROI-S05934

- 14 -

(9) In the Connect Dial-up Connection window, click on Cancel button to continue. Click Properties button on Connect Dial-up Connections window.

(10) In the Dial-up Connection Properties window, verify that the selected device is Modem- Standard 19200 bps Modem [COM1] on the General tab. Click on the Configure button.

ROI-S05934

- 15 -

(11) In the Modem Configuration window, uncheck all five boxes.

(12) On the Option tab, keep default setting and click on the Security tab.

ROI-S05934

- 16 -

(13) On the Security tab, keep default setting and click on the Networking tab.

(14) On the Networking tab, verify that Type of dial-up server I am calling is set to PPP and uncheck File and Printer and Client for Microsoft options.

ROI-S05934

- 17 -

(15) Click on Settings button. Uncheck all the boxes in the ensuing window as shown in the figure below. Click OK, go back and highlight Internet Protocol (TCP/IP) then click on the properties box.

(16) Verify that both Obtain an IP address automatically and Obtain DNS server address automatically are selected. Click on Advanced ... button.

ROI-S05934

- 18 -

(17) In the Advanced TCP/IP Settings window, uncheck Use IP header compression in the PPP link. Click OK button.

(18) On the Advanced tab, keep default setting and click OK button.

ROI-S05934

- 19 -

5. SNMP Service Setting

NOTE

It is necessary to remove SNMP Service or to stop it, if it has already been installed.

To Remove SNMP Service: (1) Select Start Setting Control Panel, then, in the Add or Remove Programs window, click

Add/Remove Windows Components.

(2) The Windows Components Wizard window appears. Remove the check from Management and Monitoring Tools, and then click Details....

ROI-S05934

- 20 -

(3) The Management and Monitoring Tools window appears. Confirm that Simple Network Management Protocol is not checked and click [OK]. Return to above window and click [Next].

(4) Click [Finish] to complete the removal of SNMP Service.

ROI-S05934

- 21 -

To Stop SNMP Service:

(1) To stop SNMP Service without removing it, click Administrative Tools in the Control Panel window.

(2) Click Services in the Administrative Tools window.

ROI-S05934

- 22 -

(3) Confirm that SNMP Service is installed and it has started automatically. Select Action Properties on the menu bar in the Services window, or right-click SNMP Service and then click Properties in the SNMP Service pop-up menu..

(4) Select Manual in the Startup type field and click Stop in the Service status field on the General tab. Click [OK] or [Apply].

ROI-S05934

- 23 -

(5) Confirm that the Status of both SNMP Service and SNMP Trap Service is Stopped, and that the startup condition for each one is Manual.

(6) Restart the computer.

ROI-S05934

- 24 -

6. PNMS Setup

NOTE

If PNMS software has already been installed, please uninstall it before you install a new version.

(1) Specify the folder for the PNMS installation software. Double-click setupwin32.exe.

(2) The following window appears until loading is completed.

ROI-S05934

- 25 -

(3) The Welcome Message window appears. Click [Next].

(4) Specify the directory where the PNMS is to be installed. Click [Next].

NOTE

The default path is C:\PNMSj. It is not possible to include blank spaces as in “Program Files”.

ROI-S05934

- 26 -

(5) Specify the License.Key file if one is available. Click [Next]

NOTE

If no license key file is available, operation in trial mode is possible: simply leave the LicenseKeyFile field blank and proceed.

IMPORTANT: IMMEDIATE IMPORT OF LICENSE

You may use the PNMS on a trial basis for 30 days. After that the PNMS can ONLY be used IF the license has been imported (activated). To obtain the license please contact NEC.

ROI-S05934

- 27 -

(6) Specify the directory for storing PNMS log files. Click [Next].

NOTE

The default path is <PNMSj Install Directory> when a Stored Directory is not specified. It is not possible to include blank spaces as in “Program Files”.

(7) Click [Install]

ROI-S05934

- 28 -

(8) During installation, this window appears.

(9) Click [Finish] to close the PNMS installation wizard.

ROI-S05934

- 29 -

7. Launching PNMS

(1) Click Start Programs PNMSj PNMS to start the application.

(2) If the following window appears, select [Unblock]. (When using the Windows Firewall of

Windows XP SP2.)

ROI-S05934

- 30 -

(3) Input user name and password. Select the Connection Entry:

After installation of PNMS, the initial password status will be.

User name: admin

Password: (There is no initial password. Just press Enter .

A password can then be set.)

NOTE

If another application is using the SNMP Port, application initialization will not be possible, the application will shut down, and the following message will appear.