Upload
1234abcd
View
212
Download
0
Embed Size (px)
Citation preview
7/30/2019 INSITE_DSNT
1/32
DSNTDSNT--II
Dual Spaced Neutron Tool
Insite
7/30/2019 INSITE_DSNT
2/32
DSNTDSNT--II
INC board Insite Numar Controller
Controls all functionality of the SDLT-I
and DSNT-IMAU board
Media Access Unit
Controls communication between theINC board and GTET
7/30/2019 INSITE_DSNT
3/32
DSNTDSNT--II
Motor Control board Controls three phase dc power for
caliper motor
Determines end-of-travel Controls caliper motor movement
7/30/2019 INSITE_DSNT
4/32
DSNTDSNT--II
DC Power Supplies 3.3 volts
Digital 5 volts
Analog +/- 5 volts +/- 15 volts
- 9 volts
7/30/2019 INSITE_DSNT
5/32
DSNTDSNT--II
Neutron Detection Two He3 Detectors
1 x 4 Short Spaced
2.5 x 12 Long Spaced
Pre-Amplifiers
Amplifier/Discriminator
INC Board (count discriminated pulses)
7/30/2019 INSITE_DSNT
6/32
DSNTDSNT--II
INSITE 12 +1 Lower Connector Pins 7 and 8 are the 200 volt dc toolbuss power.
The center coax is the toolstringcommunication buss.
The upper end of the communication buss isterminated with 50-ohms in the GTET.
The lower end of the communication bussMUST be terminated with 50 ohms in thelower most tool (or bull-plug).
7/30/2019 INSITE_DSNT
7/32
DSNTDSNT--II
INSITE 31 + 1 Lower ConnectorConnects Directly to the SDLT Mandrel
7/30/2019 INSITE_DSNT
8/32
DSNTDSNT--II
When logged without the SDLT-IMandrel.
Must insert the X-Over sub
Upper 31 + 1 Insite connectorLower 12 +1 Insite connector
Sets both Mandrel Open and Close EOT linesa condition that cannot exist. So the DSN
instrument recognizes the SDL is notattached.
7/30/2019 INSITE_DSNT
9/32
DSNTDSNT--II
Master CalibrationWater Tank Background
Water Tank Ratio
Field Verifier
7/30/2019 INSITE_DSNT
10/32
DSNTDSNT--II
Master Calibration PreparationFill Water Tank
Install 31+1 to 12+1 x-over
Install 12+1 bull-plug to terminate bussInstall DSNT-I into water tank
Jumper GTET to DSNT-I
7/30/2019 INSITE_DSNT
11/32
DSNTDSNT
7/30/2019 INSITE_DSNT
12/32
7/30/2019 INSITE_DSNT
13/32
7/30/2019 INSITE_DSNT
14/32
7/30/2019 INSITE_DSNT
15/32
7/30/2019 INSITE_DSNT
16/32
7/30/2019 INSITE_DSNT
17/32
7/30/2019 INSITE_DSNT
18/32
7/30/2019 INSITE_DSNT
19/32
7/30/2019 INSITE_DSNT
20/32
7/30/2019 INSITE_DSNT
21/32
7/30/2019 INSITE_DSNT
22/32
PARAMETERSPARAMETERS
7/30/2019 INSITE_DSNT
23/32
Constant TemperatureConstant Temperature
7/30/2019 INSITE_DSNT
24/32
Gradient TemperatureGradient Temperature
7/30/2019 INSITE_DSNT
25/32
Tool TemperatureTool Temperature
7/30/2019 INSITE_DSNT
26/32
Constant PressureConstant Pressure
7/30/2019 INSITE_DSNT
27/32
Gradient PressureGradient Pressure
7/30/2019 INSITE_DSNT
28/32
Mud Weight PressureMud Weight Pressure
7/30/2019 INSITE_DSNT
29/32
Well ParametersWell Parameters
7/30/2019 INSITE_DSNT
30/32
DSNTDSNT--I LoggingI Logging
De-CentralizationDe-Centralize in boreholes7 7/8 up to 17 inches
Remove De-Centralizer in boreholesless than 7 7/8 inches
Align with SDLT-I Caliper
Use Indents for proper locationWithin 5 of top
7/30/2019 INSITE_DSNT
31/32
7/30/2019 INSITE_DSNT
32/32