InfoLight TS Series A4 Version2 - Clonica Networks · Next Generation Light Sources TS LIGHT Series Illuminating your life and your future Info original LED product TS Series was

InfoLight Original LED Lighting specifically for Signage

TS Series

www.Info-SignSystems.com

LED for ultra small & thin signs

Waterproof LED lighting strip

LED for medium & large size signs

LED for illuminating large areas of thin signs

Illuminates sideway direction. Can be used as light source of small signs and indirect lighting.

Ultra thin unit covered with silicon tube.

Ideal for internal illumination of middle & large size signs.

Suitable for indirect lighting of middle & large size signs.

Minimum number of modules to be used of each unitPower Supply

Basic Connection

Ideal for internal illumination of thin signs.

Illuminates upward direction. Can be used as light source of small signs and indirect lighting.

TS Series TV

TS Series SV

TS Series WP

TS Series TR

TS Series BT

TS Series BB

Contents

Next Generation Light Sources

TS LIGHT Series

Illuminating your life and your future

Info original LED product TS Series was developed

specifically for sign illumination. A wide range of LED

units, including ultra thin type for narrow space installa-

tion, waterproof type, high-intesity type for medium and

large signs, are available. We pursue ecologically

friendly sign products through producing these flexible

LED units as an alternative to neon tubes or fluorescent.

Attractive features of LED

Low Power Consumption & Longevity

Eco-friendly & RoHS Compliant

High-Intensitywith Lower Power

You can save up to 80% power consumption by replacing fluores -cent lamps with LEDs. Running cost, including maintenance and initial cost, with 20 hours opera -tion will be reduced in about 18 months after replacement.

TS LIGHT Series are compliant with RoHS directive issued in EU countries and do not use harmful restricted substances. We continue developing eco-friendly products.

Info original LED unit, TS Series

Special Features

Info original LED unit

TS Series

Reduce power consump -tion by 30% to 50%, compared with equivalent products.

Use heat-resistant materials to withstand operation under high temperature.

Minimum size and light weight improve felxibility for installation.

Screen each LED chip and improve uniformity of luminance and color temperature.

LED modules adopt double elements (2in Chip) and achievebrightness twice as much as conventionalLED’s. They also have wide angle lenses(120 degree illuminating angle).Uneven brightness is reduced bywidening the space between modules.

LED Unit for ultra small & thin signs

White Warm White

Upward illumination for narrow and small spaces.Illuminates in an upward direction from the film substrate.Suitable for narrow and small space installations andcan be used as light source for ultra small signs.

TS Series TV

Features of

These LED units easilybend and fold as youlike and can be installedin rounded or narrow spaces.

Power consumption per stripis about 1.5W. Low powerconsumption design.

The back side of the strip hasself adhesive tape, and can beattached to a narrow andcurved area of the sign byfolding it light ly.

The following is full-size illustration of the product

Cut-Out Letters with indirect lighting (H100mm)

How to Use

Specification

Can be attached to anarrow and curved sign.

Solder the power supplycable at the contactpoint.

Cathode contact point Anode contact point

polyimide<Substrate>: flexible substrate

One module consists of four LEDs. You can cut every module (four LEDs) point (See the above image). If you want to cut the strip at other point, you have to connect the contact points with soldering (See page15).

TS Series TV

Fits Any Space!

Low Power Consumption

LED strip for ultra small & thin signs

Sideway illumination type for narrow and small space.Illuminates in a sideway direction. Suitable for narrow and small space installation and can be usedas light source for ultra small signs and indirect lighting.

TS Series SV

Features of TS Series SV


Power consumption per stripis about 1.5W. Low powerconsumption design.

Built-Up Letters with indirect lighting (H150mm)

The reverse of the LED strip is self adhesive, and it can beattached to a narrow andcurved area of the sign byfolding it light ly.


How to Use

The following is full-size illustration of the product.

Specification

Cathode contact point Anode contact point

polyimide<Substrate>: flexible substrate

One module consists of four LEDs. You can cut every module (four LEDs) point (See the above image). If you want to cut the strip at other point, you have to connect the contact points with soldering (See page15).

Solder the power supplycable at the contactpoint.

Fits any Space !

Low Power Consumtion

Waterproof LED

Waterproof typefor exterior use.The TS Series WP is suitable for exterior use dueto its waterproof nature. LED units covered witha silicon tube, prevent rainwater infiltration.

TS Series WP

Features of TS Series WP


Power consumption per stripis about 1.2 W. Low powerconsumption design.

Built-Up Letters with internal illumination (H150mm)

The LED strip is covered with a soft silicon tube, and can beattached to a narrow andcurved area of the sign byfolding it light ly.

How to Use


With a waterproof connector

- Size: L350mm × W3mm × H5mm (excluding connector)- Weight: 7g (approximately)- Number of LEDs: 21 (17mm pitch)- LEDs: High-intensity LED (by TOYODA GOSEI CO.,LTD.) brightness: 1500mcd (approx.), view angle: 105˚- Drive voltage: 12Vdc

- Power consumption: 1.2W (12V/0.1A)- Operating environment: -30˚C to +60˚C (without freezing and condensation)- Water resistance: Drip-proof (for exterior use/do not use under-water)- Available number of connection: Up to 8 strips (another 8 have to be separated.)- Material: <Base>: polyimide <Substrate>: flexible substrate

<Tube>: silicon square tube <Connector>: waterproof connector

and stainless steel hook,they can be used for exteriorapplications.

Easy to connect eachunit.

The following is full-size illustration of the product

Cross-sectional view

Waterproof connector

One module consists of three LEDs. You can cut every module (three LEDs) point (See the above image). You have to conceal the cut area when you cut the strip (See page 15).

Specification

Fits Any Space

Low PowerConsumption


Suitable for internal illuminationof middle & large size signs.Triangular shape of this LED unit enablesarrangement with equal spacing in theinternal of the sign.

TS Series TR

Features of TS Series TR

Heat-Resistant Material

This unit adopts heat-resistantmaterials to be used underhigh temperature.

Power consumption per unitis about 0.25W. Low power consumption design .

Large size sign with internal illumination (H2,500mm)

Set the unit with equal spacing(50 to 80mm pitch), so as not tomake an uneven brightnessaccording to the sign depth.

How to Use

Set with equal spacingto avoid uneven brightness.

Fix at least one unit by screws or adhesive. Cables or wires shouldalso be fixed by adhesive tape soas not to interrupt illumination.

At least one unit must be fixed by screws or adhesive.

SpecificationThe following is full-size illustration of the product.

Relation between pitch, depth, and brightnessmilky white acrylic

- Size: L35mm × W35mm × D6mm - Weight: 5g (approximately) (including cords)- Number of LEDs: 3 (20mm pitch)- LEDs: High-intensity LED (by TOYODA GOSEI CO.,LTD.) brightness: 2000mcd (approx.), view angle: 105˚- Drive voltage: 12Vdc

- Power consumption: 0.25W (12V/0.02A)- Operating environment: -30˚C to +80˚C (without freezing and condensation)- Water resistance: Drip-proof (for exterior use/do not use under-water)- Available number of connection: Up to 100 units (another 100 have to be separated.)- Material: <Base>: polycarbonate <Cord>: heat resistant wire

<Substrate>: glass epoxy <Filled resin>: heat resistant silicon

Low Power Consumtion


Suitable for indirect lightingof middle & large size signs.

TS Series BT

This LED unit has been designed specifically for installing into thin fonts (such as Helvetica 45) and is also anideal light source of indirect lighting

This LED unit has been designed specifically for installing into thin fonts (such as Helvetica 45) and is also anideal light source of indirect lighting

Features of TS Series BT

Heat-Resistant Material

This unit adopts heat-resistantmaterials to be used underhigh temperature.

Power consumption per unitis about 0.25W. Low power consumption design .

How to Use

Set with equal spacing (30 to 50mm pitch) in the back side of the sign along circumference.

Fix at least one unit by screws or adhesive. Cables or wiring shouldalso be fixed by adhesive tape soas not to interrupt illumination.

At least one unit must be fixed by screws or adhesive.

SpecificationThe following is full-size illustration of the product.

- Size: L28mm × W8mm × D6mm (per one module)- Weight: 6g (approximately) (one unit, including cords)- Number of LEDs: One per module- LEDs: High-intensity LED (by TOYODA GOSEI CO.,LTD.) brightness: 2000mcd (approx.), view angle: 105˚- Drive voltage: 12Vdc

- Power consumption: 0.25W (12V/0.02A)(one unit: three modules)- Operating environment: -30˚C to +80˚C (without freezing and condensation)- Water resistance: Drip-proof (for exterior use/do not use under-water)- Available number of connection: Up to 50 units (150 modules) (another 50 have to be separated.)- Material: <Case>: polycarbonate <Cord>: heat resistant wire

<Substrate>: glass epoxy <Filled resin>: heat resistant silicon

One unit consists of three modules. You can cut every unit (three modules) point. Please cut the area that has only two cords (See page 15).

Large Bulit-Up Letters with indirect lighting (H1,000mm)

Low Power Consumption

LED for large illumination areas of thin signs

of thin signs, like poster cases.Suitable for internal illumination

This LED unit is ideal for a light source of thin signs.Internal illumination of large surface areas.You can split the LED board according to the sign size.

TS Series BB

Features of TS Series BB

Easy to adjust the size!

You can split the unit from42mm × 42mm (min.). It canbe used in various size.

Power consumption per moduleis about 0.3W. Low power consumption design .

How to Use

Specification

After splitting the unit according

fix it by double sided adhesive, screws, or other adhesive.

Split the unit to adjustthe size and then attach it.

to the attachment area size,

Connect the cords of each module by soldering.

The above is full-size illustration of the product

Relation between depth and brightnessmilky white acrylic

- Size: W252mm × H210mm × D3mm (per one sheet)- Weight: 170g (approximately) (one sheet)- Number of LEDs: 120 per sheet- LEDs: High-intensity LED (by TOYODA GOSEI CO.,LTD.) brightness: 2000mcd (approx.), view angle: 105˚- Drive voltage: 15Vdc

- Power consumption: 9W (15V/0.6A)(0.3W per module)- Operating environment: -30˚C to +60˚C (without freezing and condensation)- Water resistance: No water resistance (interior use only)- Available number of connection: Up to 20 sheets (120 modules) (another 20 have to be separated.)- Material: <Substrate>: glass epoxy (single-sided)

One unit (sheet) consists of 30 modules (6 × 5 modules). You can split every module to use.

Thin poster case with internal illumination (D35mm)

Low Power Consumtion!

Every single unit of TS Series TR can be used separately. Single unit contains three LEDs.

Single unit of TS Series BT consists of three modules. Three modules must be used as one set. Please cut the area that has only two cables.

Single module of TS Series BB has four LEDs on the 42mm × 42mm square board. LEDs are arranged every 21mm pitch.

After splitting the module, please connect the cords by soldering.

You can split the board with your hands.

i c k

TS Series TR

TS Series BT

TS Series BB

Power Supply

We offer switching power supply for tsLIGHT series. If you need other power supply not shown below, please contact us.

Switching power supply for tsLIGHT (by TDK Corporation, NOT waterproof type)

AC/DC switching power supply for TS Series

Waterproof switching power supply for tsLIGHT (by Nagano Nihon Radio Co.,Ltd.)

OutputMax. voltage 12Vdc 15Vdc

100Vac to 240Vac

Note: The above figures are calculated as the safety factor of 70%.

Input voltageSize (mm)

70 (units) 140 (units)70 (units) 140 (units)

87 (units)

N/A N/AN/A

N/A

N/A N/AN/AN/A

N/A

N/A

N/A

N/A N/A

N/A

N/A

N/A N/AN/AN/A

N/AN/A

N/A

N/A

N/A N/A

N/A N/A

N/A N/A

175 (units)420 (units) 840 (units)420 (units) 840 (units)

350 (modules) 700 (modules)

stinu fo rebmun .xaM

OutputMax. voltage 12Vdc

100Vac or 200Vac



38 (units)180 (units)180 (units)


st in u f o re bm un .xaM

OutputMax. voltage 12Vdc 15Vdc 16Vdc

100Vac to 240Vac




7 (units) 35 (units)33 (units) 170 (units)33 (units) 170 (units)


stinu f o re bm un .xaM

N/A

Switching power supply for tsLIGHT (by TDK Corporation, NOT waterproof type)

OutputMax. voltage 12Vdc 15Vdc

100Vac to 240VV VacVV




87 (units)

N/A N/AN/A

N/A

N/A N/AN/AN/A

N/A

N/A

N/A

175 (units)420 (units) 840 (units)420 (units) 840 (units)


stinuf ore bm un.xaM

N/A

Not available for UK or EU markets.

Waterproof switching power supply for tsLIGHT (by Nagano Nihon Radio Co.,Ltd.)

N/A N/A

N/A N/A

N/A N/A

OutputMax. voltage 12Vdc

100Vac or 200VV VacVV





st in uf ore bm un.xaM

Not available for UK or EU markets

Basic Connection

Connect anode electrodes of the products to the anode of the power supply. Likewise, connect cathode electrodes to the cathode of the power supply. Note: They must be connected in parallel.

Basic Connection Diagram

Crimping terminal

Crimping terminal Crimping terminal

Crimping terminal

Extender cableSwitching power supply

100Vac or 200Vac

Info Sign Systems is a member of Info Holdings

Documents

InfoLight TS Series A4 Version2 - Clonica Networks · Next Generation Light Sources TS LIGHT Series Illuminating your life and your future Info original LED product TS Series was