Embed Size (px)
Citation preview
INDUCTION MOTORS
1. Characteristic of Induction MotorThe induction motor is classified into a single-phase
motor and a three-phase motor according to the using
power source. This motor always uses both auxiliary
winding and condenser not only when starting but
also during operation. Generally speaking, its starting
torque is not so great, but its structure is simple and
reliable. In addition, its connection is simple. It is
suitable to use in houses and on factories. For a
single-phase induction motor, be sure that the
condenser indicated in the name plate should comply
with the capacity of the motor.
For a single-phase induction motor, it is not possible
to reverse the direction of rotation within a short time
during operation because of the inertia torque exerting
adversely against the direction the motor is supposed
to change to. Thus, stop the motor first and change
the rotational direction next. In case you do not, the
motor can be damaged.
The power source of a single-phase motor includes U
(100V 60.60Hz), C (200V 50/60Hz, 220V 50/60Hz,
230V 50Hz). Refer to (Fig. 1).
The three-phase induction motor has simpler
connection, and higher efficiency and reliability than
the single-phase motor, because it can be driven by a
three-phase power source directly. The three-phase
motor is popular as a general-purpose motor. The
power source for a three-phase motor includes H
(220V 50/60Hz), M (380V 50/60Hz), Z (440V
50/60Hz). Refer to (Fig. 2).
It is possible to use the motor for continuous rated
operation.
It is designed to be used in a single direction.
The number of rated revolution of the motor varies
depending on the load imposed on it.
xIt is suitable for such operation that does not need
the speed control.
Its insulation class is E. Our UL conformance motor is
class A.
2. Characteristic of Rotation and TorqueUnder a constant voltage, the relationship between
the number of rotation and the torque is as shown in
(Fig. 3). With no-load, the number of rotation roughly
approximates the number of synchronous rotation,
but as the load increases, the number of rotation
decreases and reaches the torque TL The stable
zone is to this point.
When the load is further increased and over the point
TM, that is, the torque of the motor reaches the
unstable zone, the motor stops and restriction
electricity runs. As a result, the motor generates high
heat, and then it can be damaged. Therefore, a safe
operation is possible if only the motor is used within
the stable zone of the load.
3. Characteristic of Voltage and CondenserThe characteristic of voltage can be represented by
the torque's characteristic about the applied voltage.
The torque of induction motor changes in proportion
to two times the voltage.
The characteristic of torque also change according to
the capacity of the condenser.
As the capacity of the condenser boost, the starting
torque and stalling torque increase. But if the capacity
is increased by 2.5~3.0 folds, the operating torque
decreases and the starting torque do not increase.
As a simple method to increase the torque when the
induction motor is short on torque, either the voltage
or the condenser capacity can be increased to
continue the operation. In this case, the loss input of
the motor increases and the temperature rises
rapidly.
However, if the motor must be run with insufficient
torque, take measures to let the motor release heat
as much as possible and operate the motor while
keeping the temperature of the motor's housing below
90 Refer to (Fig. 4).
[ Characteristic of Induction Motor ]
GENERAL SPECIFICATION OF INDUCTION MOTORS
100M or more when 500V megger is applied between the windings and the housing after rated motor operation under normal ambient temperature and humidity
Sufficient to withstand 1500V at 50/60Hz applied betweenthe windings and the case after rated motor operation under normal ambient temperature and humidity
80 or less increase measured by thermometer after rated operation (less than 45 for motors with fan)
Class B (130 ), UL approval motor class A (105 )
Built-in thermal protector (automatic return type) Open : 120 5 Close 77 5
-10 ~+40
85% maximum (non condensing)
29
(Fig1)
(Fig. 2)
30 31
RatedTorquemN m(gfcm)
Speed
(rpm)
Condenser
( )
StartingTorque
(mN m)(gfcm)
Current
(A)
Frequency
(Hz)
Voltage
(V)
6
6
110
115
220
230
60
60
50
60
0.19
0.11
0.12
0.11
40
400
40400
41410
40400
40
400
40400
48480
40400
1500
1500
1250
1500
2
0.6
Output
(W)
single-phase
single-phase
INDUCTION MOTORS
6W LEAD WIRE TYPE
Model
K6IG6NU
K6IS6NU
K6IG6NC
K6IS6NC
SPECIFICATIONS
CONNECTION DIAGRAMS
DIMENSIONS
continuous rating, four poles class E or A
GEARHEADS
DIMENSIONS
DECIMAL GEARHEAD GEARHEAD
Speed(rpm)
Ratio
600
3
0.10
1.0
500
3.6
0.12
1.2
360
5
0.16
1.6
300
6
0.19
1.9
240
7.5
0.24
2.4
200
9
0.29
2.9
144
12.5
0.41
4.1
120
15
0.49
4.9
100
18
0.58
5.8
72
25
0.73
7.3
60
30
0.87
8.7
50
36
1.05
10.5
36
50
1.31
13.1
30
60
1.57
15.7
24
75
1.97
19.7
20
90
2.36
23.6
18
100
2.62
26.2
15
120
3
30
12
150
3
30
10
180
3
30
Model
Motor/
Gearhead
Gearhead and decimal gearhead are sold separately.
The code in of gearhead model is for gear ratio.
color indicates that the output shaft of the geared motor rotates in the same direction as the output shaft of the motor. Others indicate rotation in the opposite direction.
If you are to have less ratio than the ratio in the table, you can install the decimal gearhead, which has one tenth of the ratio, between the gearhead and the motor. In this case, the permissible torque is
3N m/30kgfcm.
60Hz
Speed(rpm)
Ratio
500
3
0.12
1.2
416
3.6
0.14
1.4
300
5
0.19
1.9
250
6
0.23
2.3
200
7.5
0.29
2.9
166
9
0.35
3.5
120
12.5
0.49
4.9
100
15
0.58
5.8
83
18
0.70
7.0
60
25
0.87
8.7
50
30
1.05
10.5
41
36
1.26
12.6
30
50
1.57
15.7
25
60
1.89
18.9
20
75
2.36
23.6
16
90
2.83
28.3
15
100
3
30
125
120
3
30
10
150
3
30
8.3
180
3
30
Model
Motor/
Gearhead
50Hz
APPLICATION MODELPART No. MOUNTING BOLT
DIMENSION TABLE
RATED TORQUE OF GEARHEAD
unit=above : N m / below : kgfcm
unit=above : N m / below : kgfcm
Black
White
Red
Black
Red
White
The direction of motor rotation is as viewed from the front shaft end of the motor
32 33
RatedTorque
(mN m)(gfcm)
Speed
(rpm)
Condenser
( )
StartingTorque
(mN m)(gfcm)
Current
(A)
Frequency
(Hz)
Voltage
(V)
15
15
110
115
220
230
60
60
50
60
0.36
0.37
0.18
65
650
65650
75750
65650
100
1000
1001000
1201200
1001000
1500
1500
1250
1500
4.5
1
Output
(W)
single-phase
single-phase
INDUCTION MOTORS
15W LEAD WIRE TYPE
Model
K7IG15NU
K7IS15NU
K7IG15NC
K7IS15NC
SPECIFICATIONS
CONNECTION DIAGRAMS
DIMENSIONS
continuous rating, four poles class E or A
GEARHEADS
DIMENSIONS
DECIMAL GEARHEAD GEARHEAD
Speed(rpm)
Ratio
600
3
0.24
2.4
500
3.6
0.29
2.9
360
5
0.41
4.1
300
6
0.49
4.9
240
7.5
0.61
6.1
200
9
0.73
7.3
144
12.5
1.01
10.1
120
15
1.22
12.2
100
18
1.46
14.6
72
25
1.82
18.2
60
30
2.19
21.9
50
36
2.62
26.2
36
50
3.28
32.8
30
60
3.94
39.4
24
75
4.92
49.2
20
90
5
50
18
100
5
50
15
120
5
50
12
150
5
50
10
180
5
50
Model
Motor/
Gearhead
Gearhead and decimal gearhead are sold separately.
The code in of gearhead model is for gear ratio.
color indicates that the output shaft of the geared motor rotates in the same direction as the output shaft of the motor. Others indicate rotation in the opposite direction.
If you are to have less ratio than the ratio in the table, you can install the decimal gearhead, which has one tenth of the ratio, between the gearhead and the motor. In this case, the permissible torque is
5N m/50kgfcm.
60Hz
Speed(rpm)
Ratio
500
3
0.29
2.9
416
3.6
0.35
3.5
300
5
0.49
4.9
250
6
0.58
5.8
200
7.5
0.73
7.3
166
9
0.87
8.7
120
12.5
1.22
12.2
100
15
1.46
14.6
83
18
1.75
17.5
60
25
2.19
21.9
50
30
2.62
26.2
41
36
3.15
31.5
30
50
3.94
39.4
25
60
4.72
47.2
20
75
5
50
16
90
5
50
15
100
5
50
125
120
5
50
10
150
5
50
8.3
180
5
50
Model
Motor/
Gearhead
50Hz
APPLICATION MODELPART No. L MOUNTING BOLT
DIMENSION TABLE
RATED TORQUE OF GEARHEAD
unit=above : N m / below : kgfcm
unit=above : N m / below : kgfcm
Black
White
Red
Black
Red
White
The direction of motor rotation is as viewed from the front shaft end of the motor
RatedTorque
(mN m)(gfcm)
Speed
(rpm)
Condenser
( )
StartingTorque
(mN m)(gfcm)
Current
(A)
Frequency
(Hz)
Voltage
(V)
Output
(W)Model
34 35
25
25
25115110 60 0.50
1201200
1601600 1500 5
220
230
220
230
60
50
60
60
50
0.26
0.28
0.27
0.26
0.31
1201200
1201200
1201200
1601600
2402400
1601600
1901900
1601600
1901900
1601600
1550
1300
1550
1350
60 0.271601600
1601600
1600
1600
1.5
-
single-phase
single-phase
single-phase
INDUCTION MOTORS
25W LEAD WIRE TYPE
K8IG25NC
K8IG25NUK8IS25NU
K8IS25NC
K8IG25NH
K8IS25NH
SPECIFICATIONS
CONNECTION DIAGRAMS
DIMENSIONS
GEARHEADS
DIMENSIONS
DECIMAL GEARHEAD GEARHEAD
Speed(rpm)
Ratio
600
3
500
3.6
360
5
300
6
240
7.5
200
9
144
12.5
120
15
100
18
72
25
60
30
50
36
36
50
30
60
24
75
20
90
18
100
15
120
12
150
10
180
Model
Motor/
Gearhead
Gearhead and decimal gearhead are sold separately.
The code in of gearhead model is for gear ratio.
color indicates that the output shaft of the geared motor rotates in the same direction as the output shaft of the motor. Others indicate rotation in the opposite direction.
If you are to have less ratio than the ratio in the table, you can install the decimal gearhead, which has one tenth of the ratio, between the gearhead and the motor. In this case, the permissible torque is
8N m/80kgfcm.
But, if you install 1/25~1/36 gearhead, the permissible torque is 6N m/60kgfcm.
60Hz
Speed(rpm)
Ratio
500
3
0.46
4.6
0.55
5.5
0.77
7.7
0.92
9.2
1.15
11.5
1.39
13.9
1.92
19.2
2.31
23.1
2.77
27.7
3.46
34.6
4.16
41.6
4.99
49.9
6.23
62.3
7.48
74.8
0.46
4.6
0.55
5.5
0.77
7.7
0.92
9.2
1.15
11.5
1.39
13.9
1.92
19.2
2.31
23.1
2.77
27.7
3.46
34.6
4.16
41.6
4.99
49.9
6.23
62.3
7.48
74.8
8
80
8
80
8
80
8
80
8
80
8
80
8
80
8
80
8
80
8
80
8
80
8
80
416
3.6
300
5
250
6
200
7.5
166
9
120
12.5
100
15
83
18
60
25
50
30
41
36
30
50
25
60
20
75
16
90
15
100
125
120
10
150
8.3
180
Model
Motor/
Gearhead
0.39
3.9
0.39
3.9
0.47
4.7
0.47
4.7
0.65
6.5
0.65
6.5
0.78
7.8
0.78
7.8
0.97
9.7
0.97
9.7
1.62
16.2
1.62
16.2
1.94
19.4
1.94
19.4
2.33
23.3
2.33
23.3
1.17
11.7
1.17
11.7
2.92
29.2
2.92
29.2
3.50
35.0
3.50
35.0
4.20
42.0
4.20
42.0
5.25
52.5
5.25
52.5
6.30
63.0
6.30
63.0
7.87
78.7
7.87
78.7
8
80
8
80
8
80
8
80
8
80
8
80
8
80
8
80
8
80
8
80
50Hz
APPLICATION MODELPART No. L MOUNTING BOLT
DIMENSION TABLE
RATED TORQUE OF GEARHEAD
unit=above : N m / below : kgfcm
unit=above : N m / below : kgfcm
Black
White
Red
Black
Red
White
The direction of motor rotation is as viewed from the front shaft end of the motor
Condenser
( )
36 37
INDUCTION MOTORS
40W LEAD WIRE TYPE
SPECIFICATIONS
RATED TORQUE OF GEARHEAD
CONNECTION DIAGRAMS
DIMENSIONS
continuous rating, four poles class E or A
GEARHEADS
DIMENSIONS
DECIMAL GEARHEAD GEARHEAD
Speed(rpm)
Ratio
600
3
0.63
6.3
500
3.6
0.76
7.6
360
5
1.05
10.5
300
6
1.26
12.6
240
7.5
1.58
15.8
200
9
1.90
19.0
144
12.5
2.63
26.3
120
15
3.16
31.6
100
18
3.79
37.9
72
25
4.74
47.4
60
30
5.69
56.9
50
36
6.82
68.2
36
50
8.53
85.3
30
60
10
100
24
75
10
100
20
90
10
100
18
100
10
100
15
120
10
100
12
150
10
100
10
180
10
100
Model
Motor/
Gearhead
0.61
6.1
0.73
7.3
1.01
10.1
1.22
12.2
1.52
15.2
1.82
18.2
2.53
25.3
3.04
30.4
3.65
36.5
4.56
45.6
5.47
54.7
6.56
65.6
8.20
82.0
9.84
98.4
10
100
10
100
10
100
10
100
10
100
10
100
60Hz
Speed(rpm)
Ratio
500
3
0.73
7.3
416
3.6
0.87
8.7
300
5
1.22
12.2
250
6
1.46
14.6
200
7.5
1.82
18.2
166
9
2.19
21.9
120
12.5
3.04
30.4
100
15
3.65
36.5
83
18
4.37
43.7
60
25
5.47
54.7
50
30
6.56
65.6
41
36
7.87
78.7
30
50
9.84
98.4
0.73
7.3
0.87
8.7
1.22
12.2
1.46
14.6
1.82
18.2
2.19
21.9
3.04
30.4
3.65
36.5
4.37
43.7
5.47
54.7
6.56
65.6
7.87
78.7
9.84
98.4
25
60
10
100
20
75
10
100
16
90
10
100
15
100
10
100
125
120
10
100
10
150
10
100
8.3
180
10
100
Model
Motor/
Gearhead
10
100
10
100
10
100
10
100
10
100
10
100
10
100
50Hz
APPLICATION MODELPART No. L MOUNTING BOLT
DIMENSION TABLE
40
40
40
220
115110
60
50
60 0.67
0.39
0.422402400
2102100
2102100
2602600
3003000
2602600
1550
1250 2.5
81500
230
220
230
60
60
0.40
0.33
2102100
7107100
2602600
2502500
1550
1600
50 0.369009000
3003000
1350
60 0.337107100
2502500
1600
-
single-phase
single-phase
three-phase
K9IG40NC
K9IG40NU
K9IS40NU
K9IS40NC
K9IG40NH
K9IS40NH
unit=above : N m / below : kgfcm
unit=above : N m / below : kgfcm RatedTorque
(mN m)(gfcm)
Speed
(rpm)
StartingTorque
(mN m)(gfcm)
Current
(A)
Frequency
(Hz)
Voltage
(V)
Output
(W)Model
Black
White
Red
Black
Red
White
The direction of motor rotation is as viewed from the front shaft end of the motor
Gearhead and decimal gearhead are sold separately.
The code in of gearhead model is for gear ratio.
color indicates that the output shaft of the geared motor rotates in the same direction as the output shaft of the motor. Others indicate rotation in the opposite direction.
If you are to have less ratio than the ratio in the table, you can install the decimal gearhead, which has one tenth of the ratio, between the gearhead and the motor. In this case, the permissible torque is
10N m/100kgfcm.
38 39
INDUCTION MOTORS
60W LEAD WIRE TYPE
CONNECTION DIAGRAMS
DIMENSIONS
GEARHEADS
DIMENSIONS
DECIMAL GEARHEAD GEARHEAD
APPLICATION MODELPART No. L MOUNTING BOLT
DIMENSION TABLE
SPECIFICATIONS
continuous rating, four poles class E or A
RatedTorque
(mN m)(gfcm)
Speed
(rpm)
Condenser
( )
StartingTorque
(mN m)(gfcm)
Current
(A)
Frequency
(Hz)
Voltage
(V)
60
60
60
230
220
115
110
60
50
60 1.30
0.60
0.623903900
3503500
3503500
4004000
4704700
4004000
1550
1250 4
161550
220
60
60
0.72
0.48
3503500
145014500
4004000
3703700
1550
1600
23050
60
0.63
0.49
115011500
145014500
4604600
3703700
1350
1600
-
Output
(W)
single-phase
single-phase
single-phase
Model
K9IP60FC
K9IP60FUK9IS60FU
K9IS60FC
K9IP60FH
K9IS60FH
RATED TORQUE OF GEARHEAD
Speed(rpm)
Ratio
600
3
500
3.6
360
5
300
6
240
7.5
200
9
144
12.5
120
15
100
18
72
25
60
30
50
36
36
50
30
60
24
75
20
90
18
100
15
120
12
150
10
180
Model
Motor/
Gearhead
60Hz
Speed(rpm)
Ratio
500
3
1.14
11.4
1.12
11.2
1.37
13.7
1.34
13.4
1.90
19.0
1.86
18.6
2.28
22.8
2.24
22.4
2.86
28.6
2.79
27.9
3.43
34.3
3.35
33.5
4.28
42.8
4.19
41.9
5.14
51.4
5.03
50.3
6.17
61.7
6.04
60.4
7.71
77.1
7.55
75.5
9.25
92.5
9.05
90.5
11.10
111.0
10.87
108.7
15.42
154.2
15.09
150.9
18.50
185.0
18.11
181.1
20
200
20
200
20
200
20
200
20
200
20
200
20
200
20
200
20
200
20
200
20
200
20
200
416
3.6
300
5
250
6
200
7.5
166
9
120
12.5
100
15
83
18
60
25
50
30
41
36
30
50
25
60
20
75
16
90
15
100
125
120
10
150
8.3
180
Model
Motor/
Gearhead
0.97
9.7
0.90
9.0
1.17
11.7
1.08
10.8
1.62
16.2
1.50
15.0
1.94
19.4
1.80
18.0
2.43
24.3
2.25
22.5
2.92
29.2
2.70
27.0
3.65
36.5
3.37
33.7
4.37
43.7
4.05
40.5
5.25
52.5
4.86
48.6
6.56
65.6
6.07
60.7
7.87
78.7
7.28
72.8
9.45
94.5
8.74
87.4
13.12
131.2
12.14
121.4
15.75
157.5
14.57
145.7
17.71
177.1
16.39
163.9
20
200
19.66
196.6
20
200
20
200
20
200
20
200
20
200
20
200
20
200
20
200
50Hzunit=above : N m / below : kgfcm
unit=above : N m / below : kgfcm
Black
White
Red
Black
Red
White
The direction of motor rotation is as viewed from the front shaft end of the motor
Gearhead and decimal gearhead are sold separately.
The code in of gearhead model is for gear ratio.
color indicates that the output shaft of the geared motor rotates in the same direction as the output shaft of the motor. Others indicate rotation in the opposite direction.
If you are to have less ratio than the ratio in the table, you can install the decimal gearhead, which has one tenth of the ratio, between the gearhead and the motor. In this case, the permissible torque is
20N m/200kgfcm.
RatedTorque
(mN m)(gfcm)
Speed
(rpm)
Condenser
( )
StartingTorque
(mN m)(gfcm)
Current
(A)
Frequency
(Hz)
Voltage
(V)
Output
(W)Model
40 41
INDUCTION MOTORS
90W LEAD WIRE TYPE
CONNECTION DIAGRAMS
DIMENSIONS
GEARHEADS
DIMENSIONS
DECIMAL GEARHEAD GEARHEAD
Speed(rpm)
Ratio
600
3
500
3.6
360
5
300
6
240
7.5
200
9
144
12.5
120
15
100
18
72
25
60
30
50
36
36
50
30
60
24
75
20
90
18
100
15
120
12
150
10
180
Model
Motor/
Gearhead
60Hz
Speed(rpm)
Ratio
500
3
1.73
17.3
1.65
16.5
2.07
20.7
1.98
19.8
2.88
28.8
2.75
27.5
3.45
34.5
3.30
33.0
4.31
43.1
4.13
41.3
5.18
51.8
4.96
49.6
6.47
64.7
6.20
62.0
7.76
77.6
7.44
74.4
9.32
93.2
8.92
89.2
11.65
116.5
11.15
111.5
13.97
139.7
13.38
133.8
16.77
167.7
16.06
160.6
20
200
20
200
20
200
20
200
20
200
20
200
20
200
20
200
20
200
20
200
20
200
20
200
20
200
20
200
20
200
20
200
416
3.6
300
5
250
6
200
7.5
166
9
120
12.5
100
15
83
18
60
25
50
30
41
36
30
50
25
60
20
75
16
90
15
100
125
120
10
150
8.3
180
Model
Motor/
Gearhead
1.39
13.9
1.34
13.4
1.66
16.6
1.60
16.0
2.31
23.1
2.23
22.3
2.77
27.7
2.67
26.7
3.46
34.6
3.34
33.4
4.16
41.6
4.01
40.1
5.19
51.9
5.01
50.1
6.23
62.3
6.01
60.1
7.48
74.8
7.22
72.2
9.35
93.5
9.02
90.2
11.22
112.2
10.83
108.3
13.46
134.6
12.99
129.9
18.70
187.0
18.04
180.4
20
200
20
200
20
200
20
200
20
200
20
200
20
200
20
200
20
200
20
200
20
200
20
200
20
200
20
200
50Hz
RATED TORQUE OF GEARHEAD
SPECIFICATIONS
continuous rating, four poles class E or A
90
90
90
220
115
110
60
50
60 2.00
0.90
1.11
5005000
5505500
6006000
5000
500
5700
570
7107100
5705700
1600
1300 6
201600
230
220
60
60
1.00
0.68160016000
5705700
5505500
1600
1600
230
50
60
0.85
0.71
205020500
160016000
6806800
5505500
1350
1600
-
single-phase
single-phase
single-phase
K9IP90FC
K9IP90FU
K9IS90FU
K9IS90FC
K9IP90FH
K9IS90FH
unit=above : N m / below : kgfcm
unit=above : N m / below : kgfcm
APPLICATION MODELPART No. L MOUNTING BOLT
DIMENSION TABLE
Black
White
Red
Black
Red
White
The direction of motor rotation is as viewed from the front shaft end of the motor
Gearhead and decimal gearhead are sold separately. The code in of gearhead model is for gear ratio.
color indicates that the output shaft of the geared motor rotates in the same direction as the output shaft of the motor. Others indicate rotation in the opposite direction.
If you are to have less ratio than the ratio in the table, you can install the decimal gearhead, which has one tenth of the ratio, between the gearhead and the motor. In this case, the permissible torque is
20N m/200kgfcm.
1.39
13.9
1.34
13.4
1.66
16.6
1.60
16.0
2.31
23.1
2.23
22.3
2.77
27.7
2.67
26.7
3.46
34.6
3.34
33.4
4.16
41.6
4.01
40.1
5.19
51.9
5.01
50.1
6.23
62.3
6.01
60.1
7.48
74.8
7.22
72.2
9.35
93.5
9.02
90.2
11.22
112.2
10.83
108.3
13.46
134.6
12.99
129.9
18.70
187.0
18.04
180.4
22.44
224.4
21.65
216.5
25.24
252.4
24.36
243.6
30
300
29.23
292.3
30
300
30
300
30
300
30
300
30
300
30
300
30
300
30
300
1.73
17.3
1.65
16.5
2.07
20.7
1.98
19.8
2.88
28.8
2.75
27.5
3.45
34.5
3.30
33.0
4.31
43.1
4.13
41.3
5.18
51.8
4.96
49.6
6.47
64.7
6.20
62.0
7.76
77.6
7.44
74.4
9.32
93.2
8.92
89.2
11.65
116.5
11.15
111.5
13.97
139.7
13.38
133.8
16.77
167.7
16.06
160.6
23.29
232.9
22.31
223.1
27.95
279.5
26.77
267.7
42 43
GEARHEADS
DIMENSIONS
DECIMAL GEARHEAD GEARHEAD
APPLICATION MODELPART No. L MOUNTING BOLT
DIMENSION TABLEAPPLICATION MODELPART No. L MOUNTING BOLT
DIMENSION TABLE
GEARHEADS
DIMENSIONS
DECIMAL GEARHEAD GEARHEAD
Speed(rpm)
Ratio
600
3
500
3.6
360
5
300
6
240
7.5
200
9
144
12.5
120
15
100
18
72
25
60
30
50
36
36
50
30
60
24
75
20
90
18
100
15
120
12
150
10
180
Model
Motor/
Gearhead
60Hz
Speed(rpm)
Ratio
500
3
1.73
17.3
1.65
16.5
2.07
20.7
1.98
19.8
2.88
28.8
2.75
27.5
3.45
34.5
3.30
33.0
4.31
43.1
4.13
41.3
5.18
51.8
4.96
49.6
6.47
64.7
6.20
62.0
7.76
77.6
7.44
74.4
9.32
93.2
8.92
89.2
11.65
116.5
11.15
111.5
13.97
139.7
13.38
133.8
16.77
167.7
16.06
160.6
20
200
20
200
20
200
20
200
20
200
20
200
20
200
20
200
20
200
20
200
20
200
20
200
20
200
20
200
20
200
20
200
416
3.6
300
5
250
6
200
7.5
166
9
120
12.5
100
15
83
18
60
25
50
30
41
36
30
50
25
60
20
75
16
90
15
100
12.5
120
10
150
8.3
180
Model
Motor/
Gearhead
1.39
13.9
1.34
13.4
1.66
16.6
1.60
16.0
2.31
23.1
2.23
22.3
2.77
27.7
2.67
26.7
3.46
34.6
3.34
33.4
4.16
41.6
4.01
40.1
5.19
51.9
5.01
50.1
6.23
62.3
6.01
60.1
7.48
74.8
7.22
72.2
9.35
93.5
9.02
90.2
11.22
112.2
10.83
108.3
13.46
134.6
12.99
129.9
18.70
187.0
18.04
180.4
20
200
20
200
20
200
20
200
20
200
20
200
20
200
20
200
20
200
20
200
20
200
20
200
20
200
20
200
50Hz
RATED TORQUE OF GEARHEAD
unit=above : N m / below : kgfcm
unit=above : N m / below : kgfcm
Speed(rpm)
Ratio
600
3
500
3.6
360
5
300
6
240
7.5
200
9
144
12.5
120
15
100
18
72
25
60
30
50
36
36
50
30
60
24
75
20
90
18
100
15
120
12
150
10
180
Model
Motor/
Gearhead
60Hz
Speed(rpm)
Ratio
500
3
30
300
30
300
30
300
30
300
30
300
30
300
30
300
30
300
30
300
30
300
30
300
30
300
416
3.6
300
5
250
6
200
7.5
166
9
120
12.5
100
15
83
18
60
25
50
30
41
36
30
50
25
60
20
75
16
90
15
100
12.5
120
10
150
8.3
180
Model
Motor/
Gearhead
50Hz
RATED TORQUE OF GEARHEAD
unit=above : N m / below : kgfcm
unit=above : N m / below : kgfcm
Gearhead and decimal gearhead are sold separately.
The code in of gearhead model is for gear ratio.
color indicates that the output shaft of the geared motor rotates in the same direction as the output shaft of the motor. Others indicate rotation in the opposite direction.
If you are to have less ratio than the ratio in the table, you can install the decimal gearhead, which has one tenth of the ratio, between the gearhead and the motor. In this case, the permissible torque is
20N m/200kgfcm.
Gearhead and decimal gearhead are sold separately.
The code in of gearhead model is for gear ratio.
color indicates that the output shaft of the geared motor rotates in the same direction as the output shaft of the motor. Others indicate rotation in the opposite direction.
If you are to have less ratio than the ratio in the table, you can install the decimal gearhead, which has one tenth of the ratio, between the gearhead and the motor. In this case, the permissible torque is
30N m/300kgfcm.
44 45
INDUCTION MOTORS
120W LEAD WIRE TYPE
CONNECTION DIAGRAMS
DIMENSIONS
SPECIFICATIONS
continuous rating, four poles class E or A
RatedTorque
(mN m)(gfcm)
Speed
(rpm)
Condenser
( )
StartingTorque
(mN m)(gfcm)
Current
(A)
Frequency
(Hz)
Voltage
(V)
120
120
220
115
110
60
60 2.2
1.10600
6000
6200
600
7400
740
7400
7401600 7.0
301600
Output
(W)
single-phase
single-phase
Model
K9IP120FC
K9IP120FU
K9IS120FU
K9IS120FC
GEARHEADS
DIMENSIONS
DECIMAL GEARHEAD GEARHEAD
Speed(rpm)
Ratio
600
3
500
3.6
360
5
300
6
240
7.5
200
9
144
12.5
120
15
100
18
72
25
60
30
50
36
36
50
30
60
24
75
20
90
18
100
15
120
12
150
10
180
Model
Motor/
Gearhead
60Hz
1.80
18.0
2.16
21.6
3.00
30.0
3.60
36.0
4.50
45.0
5.39
53.9
6.74
67.4
8.09
80.9
9.71
97.1
12.14
121.4
14.57
145.7
17.48
174.8
20
200
20
200
20
200
20
200
20
200
20
200
20
200
20
200
RATED TORQUE OF GEARHEAD
unit=above : N m / below : kgfcm
APPLICATION MODELPART No. L MOUNTING BOLT
DIMENSION TABLE
Black
White
Red
Black
Red
White
The direction of motor rotation is as viewed from the front shaft end of the motor
Gearhead and decimal gearhead are sold separately.
The code in of gearhead model is for gear ratio.
color indicates that the output shaft of the geared motor rotates in the same direction as the output shaft of the motor. Others indicate rotation in the opposite direction.
If you are to have less ratio than the ratio in the table, you can install the decimal gearhead, which has one tenth of the ratio, between the gearhead and the motor. In this case, the permissible torque is
20N m/200kgfcm.
46 47
GEARHEADS
DIMENSIONS
DECIMAL GEARHEAD GEARHEAD
APPLICATION MODELPART No. MOUNTING BOLT
DIMENSION TABLE APPLICATION MODELPART No. L MOUNTING BOLT
DIMENSION TABLE
GEARHEADS
DIMENSIONS
DECIMAL GEARHEAD GEARHEAD
Speed(rpm)
Ratio
600
3
500
3.6
360
5
300
6
240
7.5
200
9
144
12.5
120
15
100
18
72
25
60
30
50
36
36
50
30
60
24
75
20
90
18
100
15
120
12
150
10
180
Model
Motor/
Gearhead
60Hz
RATED TORQUE OF GEARHEAD
unit=above : N m / below : kgfcm
Speed(rpm)
Ratio
600
3
500
3.6
360
5
300
6
240
7.5
200
9
144
12.5
120
15
100
18
72
25
60
30
50
36
36
50
30
60
24
75
20
90
18
100
15
120
12
150
10
180
Model
Motor/
Gearhead
60Hz
RATED TORQUE OF GEARHEAD
unit=above : N m / below : kgfcm
1.80
18.0
2.16
21.6
3.00
30.0
3.60
36.0
4.50
45.0
5.39
53.9
6.74
67.4
8.09
80.9
9.71
97.1
12.14
121.4
14.57
145.7
17.48
174.8
20
200
20
200
20
200
20
200
20
200
20
200
20
200
20
200
1.80
18.0
2.16
21.6
3.00
30.0
3.60
36.0
4.50
45.0
5.39
53.9
6.74
67.4
8.09
80.9
9.71
97.1
12.14
121.4
14.57
145.7
17.48
174.8
24.28
242.8
29.13
291.3
30
300
30
300
30
300
30
300
30
300
30
300
Gearhead and decimal gearhead are sold separately.
The code in of gearhead model is for gear ratio.
color indicates that the output shaft of the geared motor rotates in the same direction as the output shaft of the motor. Others indicate rotation in the opposite direction.
If you are to have less ratio than the ratio in the table, you can install the decimal gearhead, which has one tenth of the ratio, between the gearhead and the motor. In this case, the permissible torque is
20N m/200kgfcm.
Gearhead and decimal gearhead are sold separately.
The code in of gearhead model is for gear ratio.
color indicates that the output shaft of the geared motor rotates in the same direction as the output shaft of the motor. Others indicate rotation in the opposite direction.
If you are to have less ratio than the ratio in the table, you can install the decimal gearhead, which has one tenth of the ratio, between the gearhead and the motor. In this case, the permissible torque is
30N m/300kgfcm.
48 49
INDUCTION MOTORS
150W LEAD WIRE TYPE
CONNECTION DIAGRAMS
DIMENSIONS
SPECIFICATIONS
continuous rating, four poles class E or A
RatedTorque(N m)(kgfcm)
Speed
(rpm)
Condenser
( )
StartingTorque(N m)(kgfcm)
Current
(A)
Frequency
(Hz)
Voltage
(V)
220150
60
50
0.9
1.02.20
22.0
1.9
19
11.0
1.10
10.2
1.021450
-
1350
Output
(W)
three-phase
Model
K9IS150FH
K9IP150FH
GEARHEADS
DIMENSIONS
DECIMAL GEARHEAD GEARHEAD
Speed(rpm)
Ratio
600
3
500
3.6
360
5
300
6
240
7.5
200
9
144
12.5
120
15
100
18
72
25
60
30
50
36
36
50
30
60
24
75
20
90
18
100
15
120
12
150
10
180
Model
Motor/
Gearhead
60Hz
RATED TORQUE OF GEARHEAD
unit=above : N m / below : kgfcm
APPLICATION MODELPART No. MOUNTING BOLT
DIMENSION TABLE
Speed(rpm)
Ratio
500
3
416
3.6
300
5
250
6
200
7.5
166
9
120
12.5
100
15
83
18
60
25
50
30
41
36
30
50
25
60
20
75
16
90
15
100
125
120
10
150
8.3
180
Model
Motor/
Gearhead
50Hzunit=above : N m / below : kgfcm
2.48
24.8
2.97
29.7
4.13
41.3
4.96
49.6
6.20
62.0
7.44
74.4
9.29
92.9
11.15
111.5
13.38
133.8
16.73
167.3
20.08
200.8
24.09
240.9
30
300
30
300
30
300
30
300
30
300
30
300
30
300
30
300
2.67
26.7
3.21
32.1
4.46
44.6
5.35
53.5
6.68
66.8
8.02
80.2
10.02
100.2
12.03
120.3
14.43
144.3
18.04
180.4
21.65
216.5
25.98
259.8
30
300
30
300
30
300
30
300
30
300
30
300
30
300
30
300
Black
White
Red
Black
Red
White
The direction of motor rotation is as viewed from the front shaft end of the motor
Gearhead and decimal gearhead are sold separately.
The code in of gearhead model is for gear ratio.
color indicates that the output shaft of the geared motor rotates in the same direction as the output shaft of the motor. Others indicate rotation in the opposite direction.
If you are to have less ratio than the ratio in the table, you can install the decimal gearhead, which has one tenth of the ratio, between the gearhead and the motor. In this case, the permissible torque is
30N m/300kgfcm.
50 51
INDUCTION MOTORS
180W LEAD WIRE TYPE
CONNECTION DIAGRAMS
DIMENSIONS
GEARHEADS
DIMENSIONS
DECIMAL GEARHEAD GEARHEAD
APPLICATION MODELPART No. L MOUNTING BOLT
DIMENSION TABLE
SPECIFICATIONS
RatedTorque(N m)(kgfcm)
Speed
(rpm)
Condenser
( )
StartingTorque(N m)(kgfcm)
Current
(A)
Frequency
(Hz)
Voltage
(V)
180
180
220
115
110
60
60 2.8
1.40.7
7.0
7.0
0.7 1.12
11.2
11.2
1.12
1600 8
351600
Output
(W)Model
K9IP180FC
K9IP180FU
K9IP180FU
K9IS180FC
Speed(rpm)
Ratio
600
3
500
3.6
360
5
300
6
240
7.5
200
9
144
12.5
120
15
100
18
72
25
60
30
50
36
36
50
30
60
24
75
20
90
18
100
15
120
12
150
10
180
Model
Motor/
Gearhead
60Hz
RATED TORQUE OF GEARHEAD
unit=above : N m / below : kgfcm
2.72
27.2
3.27
32.7
4.54
45.4
5.44
54.4
6.80
68.0
8.16
81.6
10.21
102.1
12.25
122.5
14.70
147.0
18.37
183.7
22.04
220.4
26.45
264.5
30
300
30
300
30
300
30
300
30
300
30
300
30
300
30
300
Black
White
Red
Black
Red
White
The direction of motor rotation is as viewed from the front shaft end of the motor
Gearhead and decimal gearhead are sold separately.
The code in of gearhead model is for gear ratio.
color indicates that the output shaft of the geared motor rotates in the same direction as the output shaft of the motor. Others indicate rotation in the opposite direction.
If you are to have less ratio than the ratio in the table, you can install the decimal gearhead, which has one tenth of the ratio, between the gearhead and the motor. In this case, the permissible torque is
30N m/300kgfcm.
5352
INDUCTION MOTORS
200W LEAD WIRE TYPE
CONNECTION DIAGRAMS
DIMENSIONS
GEARHEADS
DIMENSIONS
DECIMAL GEARHEAD GEARHEAD
APPLICATION MODELPART No. L MOUNTING BOLT
DIMENSION TABLE
SPECIFICATIONS
continuous rating, four poles class E or A
RatedTorque(N m)(kgfcm)
Speed
(rpm)
Condenser
( )
StartingTorque(N m)(kgfcm)
Current
(A)
Frequency
(Hz)
Voltage
(V)
220200
60
50
1.2
1.33.0
30
2.5
25
14.5
1.45
12.3
1.231600
-
1350
Output
(W)Model
K9IS200FH
K9IP200FH
Speed(rpm)
Ratio
600
3
500
3.6
360
5
300
6
240
7.5
200
9
144
12.5
120
15
100
18
72
25
60
30
50
36
36
50
30
60
24
75
20
90
18
100
15
120
12
150
10
180
Model
Motor/
Gearhead
60Hz
RATED TORQUE OF GEARHEAD
unit=above : N m / below : kgfcm
Speed(rpm)
Ratio
500
3
416
3.6
300
5
250
6
200
7.5
166
9
120
12.5
100
15
83
18
60
25
50
30
41
36
30
50
25
60
20
75
16
90
15
100
13
120
10
150
8.3
180
Model
Motor/
Gearhead
50Hzunit=above : N m / below : kgfcm
2.99
29.9
3.59
35.9
4.98
49.8
5.98
59.8
7.47
74.7
8.97
89.7
11.21
112.1
13.45
134.5
16.14
161.4
20.18
201.8
24.21
242.1
29.05
290.5
30
300
30
300
30
300
30
300
30
300
30
300
30
300
30
300
3.52
35.2
4.23
42.3
5.87
58.7
7.05
70.5
8.81
88.1
10.57
105.7
13.21
132.1
15.86
158.6
19.03
190.3
23.78
237.8
28.54
285.4
30
300
30
300
30
300
30
300
30
300
30
300
30
300
30
300
30
300
Black
White
Red
Black
Red
White
The direction of motor rotation is as viewed from the front shaft end of the motor
Gearhead and decimal gearhead are sold separately.
The code in of gearhead model is for gear ratio.
color indicates that the output shaft of the geared motor rotates in the same direction as the output shaft of the motor. Others indicate rotation in the opposite direction.
If you are to have less ratio than the ratio in the table, you can install the decimal gearhead, which has one tenth of the ratio, between the gearhead and the motor. In this case, the permissible torque is
30N m/300kgfcm.
REVERSIBLE MOTORS
56
1. Characteristic of Reversible Motor
The reversible motor is a condenser type single-phase induction
motor. Therefore, its general characteristics are as same as
those of the induction motor.
It is possible for the motor to operate in rotational direction from
normal - stop - to reverse.
The reversible motor has a temporary brake device built inside
the motor to facilitate the operation in normal as well as reverse
direction. Also, the mail and sub windings of the stator have their
windings manufactured with the same method to guarantee the
identical characteristics between them. Refer to (Fig. 2).
Also, it has a higher starting torque to facilitate the frequent
changes in rotational direction from normal direction to reverse
direction, and vice versa, within a short time. Refer to (Fig. 3).
The temporary brake is employed to prevent overrun. The
temporary brake has a little retaining force to provide excellent
instantaneous stop by preventing overrun when stopping. Refer
to (Fig. 1).
The changeover switch can help the motor reverse its rotational
direction easily within a short time so that it is suitable for such
operation that changes the rotational direction frequently from
normal to reverse, and vice versa. Therefore, this motor is called
a reversible motor.
Since the design characteristic of the reversible motor is a
capability to control the directional changes in rotation, the loss
input is larger and the temperature can rise higher compared with
the induction motor. Hence, the rated operating time is limited to
30 minutes.
Thus, 30 minutes of rated operating time means that the motor at
the rated load can have at least 30 minutes of non-stop operation
within the safe upper limit of the temperature rise. It is possible for
the motor at the intermittent load or at the light load to have non-
stop operation, if only the outer cover temperature is not over 90
.
In general, the reversible motor is as same as the induction
motor in terms of the number of rotation, and the characteristics
of torque, voltage, and condenser.
2. Temporary Brake StructureThe temporary brake of the reversible motor has
characteristics as follows.
Apply a frictional load to improve the frequent reversal
operation.
Reduce overrun.
Provide a little holding torque.
Structurally, as shown in (Fig. 1), the brake block is forcedtoward the brake wheel by a spring to make retention force.Since at the aspect of the structure of the brake as shownthe above it has a limitation to strengthen retention force,we adjusted the brake power to be about 10% of the motoroutput torque.The figures representing the holding torque and theoverrun under no-load in (Table 1) may have more or lessdeviations for each motor. They may also have somediscrepancies depending on the operating duration and theambient temperature. It is advised therefore that the tablefigures should be used only for reference purpose.The rated torque and electric current of the reversiblemotor were measured in the circumstance where thetemporary brake block is installed in the motor. Therefore,there will be no problem even if the corresponding tablefigures are used when selecting a motor. The conservativeselection of a motor is recommended, however, becausethe figures may have some deviation depending on thebrake block employed for the motor.Care should be given, because there is a case that theholding toque may fall below the figures of (Table 1) in theinitial phase of operation.
3.Operating Time and Temperature Rise Although 30 minutes of rated operating time is specified for the
reversible motor, the rated operating time may change
depending on the operation conditions if the operation
frequently repeats stop and run (On-Off) within a short period of
time.
If the reversible motor frequently repeats stop and run (On-Off)
within a short time, the starting current gets increased to cause
the motor temperature to rise. However, the longer rated
operating time may be obtained by allowing the motor to
remain stop longer, because the stoppage can provide a
chance of natural cooling for the motor to decrease its
temperature.
The conditions of the intermittent (On-Off) operation are
determined as shown in A ~ F of (Fig. 4). F stands for
continuous operation.
The characteristics shown in (Fig. 5) through (Fig. 8) represent
the measurements of the motor for 220V 50/60Hz. Naturally,
the characteristics of the motor or 220V 60Hz will have a little
greater characteristic values because of a voltage increased by
about 10%, and therefore, the recommendation is that the
motor should be operated at the temperature below the ambient
temperature.
[Characteristic of Reversible Motor]
PHASE
SINGLE
PHASE
OUTPUT
Fig1
Fig Fig
(Table1)
57
The temperature rise measurement is performed
when the motor, under no-load, is prevented rom
transferring its internal heat to the outside through the
motor's external contact points using thermograph.
This method of measurement can provide the highest
possible temperature rise.
Especially, if either a load or an inertia load is greater
than the motor's rated torque, the longer time is
required for start or directional reversal, resulting in a
greater temperature rise, which requires a user's
attention.
The specified temperature rise of the reversible motor
is 75 ( T value) in general, and be careful not to
exceed the temperature.
In reality, there is a case that the motor alone is used,
but mostly the motor is used in combination with the
gearhead. Hence, when the motor of K8RG25N is
used with no-load in combination with the gearhead of
K8G50B, the temperature rise is like a L curve shown
in (Fig. 8) and also the temperature rise becomes
lower and the operating time becomes longer by
about 30 minutes as compared with the motor shown
in (Fig. 6).
Although the principle is to keep the coil temperature
below the specified temperature for the insulation
class. It is possible to continue the operation if the
motor housing surface temperature remains less than
90 . The temperature of the motor varies depending
on the load, operating cycle, motor's mounting
method, and ambient temperature.
( Fig 4) ( Fig 5)
( Fig 6 ) ( Fig 7)
(Table 2)
( Fig 8)
Item Specification
InsulationResistance
GENERAL SPECIFICATION OF INDUCTION MOTORS
Dielectric Strength
Temperature Rise
Insulation Class
Overheat ProtectionDevice
AmbientTemperature
100M or more when 500V megger is applied between the windings and the housing after rated motor operation under normal ambient temperature and humidity
Sufficient to withstand 1500V at 50/60Hz applied betweenthe windings and the case after rated motor operation under normal ambient temperature and humidity
80 or less increase measured by thermometer after rated operation (less than 45 for motors with fan)
Class B (130 ), UL approval motor class A (105 )
Built-in thermal protector (automatic return type) Open : 120 5 Close 77 5
-10 ~ +40
85% maximum (non condensing)Ambient Humidity
58 59
RatedTorque
(mN m)(gfcm)
Speed
(rpm)
Condenser
( )
StartingTorque
(mN m)(gfcm)
Current
(A)
Frequency
(Hz)
Voltage
(V)
6
6
110
115
220
230
60
60
50
60
0.22
0.13
50500
50500
52520
50500
40400
40400
48480
40400
1500
1500
1250
1500
2.5
0.8
Output
(W)
single-phase
single-phase
REVERSIBLE MOTORS
6W LEAD WIRE TYPE
Model
K6RG6NU
K6RS6NU
K6RG6NC
K6RS6NC
SPECIFICATIONS
CONNECTION DIAGRAMS
DIMENSIONS
30 minutes rating, four poles class E or A
GEARHEADS
DIMENSIONS
DECIMAL GEARHEAD GEARHEAD
Speed(rpm)
Ratio
600
3
0.10
1.0
500
3.6
0.12
1.2
360
5
0.16
1.6
300
6
0.19
1.9
240
7.5
0.24
2.4
200
9
0.29
2.9
144
12.5
0.41
4.1
120
15
0.49
4.9
100
18
0.58
5.8
72
25
0.73
7.3
60
30
0.87
8.7
50
36
1.05
10.5
36
50
1.31
13.1
30
60
1.57
15.7
24
75
1.97
19.7
20
90
2.36
23.6
18
100
2.62
26.2
15
120
3
30
12
150
3
30
10
180
3
30
Model
Motor/
Gearhead
60Hz
Speed(rpm)
Ratio
500
3
0.12
1.2
416
3.6
0.14
1.4
300
5
0.19
1.9
250
6
0.23
2.3
200
7.5
0.29
2.9
166
9
0.35
3.5
120
12.5
0.49
4.9
100
15
0.58
5.8
83
18
0.70
7.0
60
25
0.87
8.7
50
30
1.05
10.5
41
36
1.26
12.6
30
50
1.57
15.7
25
60
1.89
18.9
20
75
2.36
2.36
16
90
2.83
28.3
15
100
3
30
125
120
3
30
10
150
3
30
8.3
180
3
30
Model
Motor/
Gearhead
50Hz
APPLICATION MODELPART No. L MOUNTING BOLT
DIMENSION TABLE
RATED TORQUE OF GEARHEAD
unit=above : N m / below : kgfcm
unit=above : N m / below : kgfcm
Black
White
Red
Black
Red
White
The direction of motor rotation is as viewed from the front shaft end of the motor
Gearhead and decimal gearhead are sold separately.
The code in of gearhead model is for gear ratio.
color indicates that the output shaft of the geared motor rotates in the same direction as the output shaft of the motor. Others indicate rotation in the opposite direction.
If you are to have less ratio than the ratio in the table, you can install the decimal gearhead, which has one tenth of the ratio, between the gearhead and the motor. In this case,
the permissible torque is 3N m/30kgfcm.
60 61
REVERSIBLE MOTORS
15W LEAD WIRE TYPE
CONNECTION DIAGRAMS
DIMENSIONS
GEARHEADS
DIMENSIONS
DECIMAL GEARHEAD GEARHEAD
RatedTorque
(mN m)(gfcm)
Speed
(rpm)
Condenser
( )
StartingTorque
(mN m)(gfcm)
Current
(A)
Frequency
(Hz)
Voltage
(V)
15
15
110
115
220
230
60
60
50
60
0.41
0.42 100 100
0.21
1000
100
1000
1000
1001000
1201200
1001000
1500
1500
1250
1500
6
1.5
Output
(W)
single-phase
single-phase
Model
K7RG15NU
K7RS15NU
K7RG15NC
K7RS15NC
SPECIFICATIONS
continuous rating, four poles class E or A
50Hz
RATED TORQUE OF GEARHEAD
unit=above : N m / below : kgfcm
APPLICATION MODELPART No. L MOUNTING BOLT
DIMENSION TABLE
Speed(rpm)
Ratio
600
3
0.24
2.4
500
3.6
0.29
2.9
360
5
0.41
4.1
300
6
0.49
4.9
240
7.5
0.61
6.1
200
9
0.73
7.3
144
12.5
1.01
10.1
120
15
1.22
12.2
100
18
1.46
14.6
72
25
1.82
18.2
60
30
2.19
21.9
50
36
2.62
26.2
36
50
3.28
32.8
30
60
3.94
39.4
24
75
4.92
49.2
20
90
5
50
18
100
5
50
15
120
5
50
12
150
5
50
10
180
5
50
Model
Motor/
Gearhead
60Hz
Speed(rpm)
Ratio
500
3
0.29
2.9
416
3.6
0.35
3.5
300
5
0.49
4.9
250
6
0.58
5.8
200
7.5
0.73
7.3
166
9
0.87
8.7
120
12.5
1.22
12.2
100
15
1.46
14.6
83
18
1.75
17.5
60
25
2.19
21.9
50
30
2.62
26.2
41
36
3.15
31.5
30
50
3.94
39.4
25
60
4.72
47.2
20
75
5
50
16
90
5
50
15
100
5
50
125
120
5
50
10
150
5
50
8.3
180
5
50
Model
Motor/
Gearhead
unit=above : N m / below : kgfcm
Black
White
Red
Black
Red
White
The direction of motor rotation is as viewed from the front shaft end of the motor
Gearhead and decimal gearhead are sold separately.
The code in of gearhead model is for gear ratio.
color indicates that the output shaft of the geared motor rotates in the same direction as the output shaft of the motor. Others indicate rotation in the opposite direction.
If you are to have less ratio than the ratio in the table, you can install the decimal gearhead, which has one tenth of the ratio, between the gearhead and the motor. In this case, the permissible torque is
5N m/ 50kgfcm.
62 63
RatedTorque
(mN m)(gfcm)
Speed
(rpm)
Condenser
( )
StartingTorque
(mN m)(gfcm)
Current
(A)
Frequency
(Hz)
Voltage
(V)
25
25
110115
220
230
60
60
50
60
0.56
0.33
0.30
0.34
1301300
1301300
1501500
1301300
2002000
2002000
2352350
2002000
1500
1500
1250
1500
6
2
Output
(W)
single-phase
single-phase
REVERSIBLE MOTORS
25W LEAD WIRE TYPE
Model
K8RG25NUK8RS25NU
K8RG25NC
K8RS25NC
SPECIFICATIONS
CONNECTION DIAGRAMS
DIMENSIONS
30 minutes rating, four poles class E or A
GEARHEADS
DIMENSIONS
DECIMAL GEARHEAD GEARHEAD
Speed(rpm)
Ratio
600
3
0.49
4.9
500
3.6
0.58
5.8
360
5
0.81
8.1
300
6
0.97
9.7
240
7.5
1.22
12.2
200
9
1.46
14.6
144
12.5
2.03
20.3
120
15
2.43
24.3
100
18
2.92
29.2
72
25
3.65
36.5
60
30
4.37
43.7
50
36
5.25
52.5
36
50
6.56
65.6
30
60
7.87
78.7
24
75
8
80
20
90
8
80
18
100
8
80
15
120
8
80
12
150
8
80
10
180
8
80
Model
Motor/
Gearhead
60Hz
Speed(rpm)
Ratio
500
3
0.57
5.7
416
3.6
0.69
6.9
300
5
0.95
9.5
250
6
1.14
11.4
200
7.5
1.43
14.3
166
9
1.71
17.1
120
12.5
2.38
23.8
100
15
2.86
28.6
83
18
3.43
34.3
60
25
4.28
42.8
50
30
5.14
51.4
41
36
6.17
61.7
30
50
7.71
77.1
25
60
8
80
20
75
8
80
16
90
8
80
15
100
8
80
125
120
8
80
10
150
8
80
8.3
180
8
80
Model
Motor/
Gearhead
50Hz
RATED TORQUE OF GEARHEAD
unit=above : N m / below : kgfcm
unit=above : N m / below : kgfcm
APPLICATION MODELPART No. L MOUNTING BOLT
DIMENSION TABLE
Black
White
Red
Black
Red
White
The direction of motor rotation is as viewed from the front shaft end of the motor
Gearhead and decimal gearhead are sold separately.
The code in of gearhead model is for gear ratio.
color indicates that the output shaft of the geared motor rotates in the same direction as the output shaft of the motor. Others indicate rotation in the opposite direction.
If you are to have less ratio than the ratio in the table, you can install the decimal gearhead, which has one tenth of the ratio, between the gearhead and the motor. In this case,
the permissible torque is 8N m/ 80kgfcm. But, if you install 1/25~1/36 gearhead, the permissible torque is 6N m/60kgfcm.
64 65
RatedTorque
(mN m)(gfcm)
Speed
(rpm)
Condenser
( )
StartingTorque
(mN m)(gfcm)
Current
(A)
Frequency
(Hz)
Voltage
(V)
40
40
110
115
220
230
60
60
50
60
0.83
0.55
0.42
0.56
3003000
3003000
3203200
3003000
2602600
3003000
2602600
2602600
1500
1500
1300
1500
10
3.5
Output
(W)
single-phase
single-phase
REVERSIBLE MOTORS
40W LEAD WIRE TYPE
Model
K9RG40NUK9RS40NU
K9RG40NC
K9RS40NC
SPECIFICATIONS
CONNECTION DIAGRAMS
DIMENSIONS
30 minutes rating, four poles class E or A
GEARHEADS
DIMENSIONS
DECIMAL GEARHEAD GEARHEAD
Speed(rpm)
Ratio
600
3
500
3.6
360
5
300
6
240
7.5
200
9
144
12.5
120
15
100
18
72
25
60
30
50
36
36
50
30
60
10
100
24
75
10
100
20
90
10
100
18
100
10
100
15
120
10
100
12
150
10
100
10
180
10
100
Model
Motor/
Gearhead
60Hz
Speed(rpm)
Ratio
500
3
0.73
7.3
416
3.6
0.87
8.7
300
5
1.22
12.2
250
6
1.46
14.6
200
7.5
1.82
18.2
166
9
2.19
21.9
120
12.5
3.04
30.4
100
15
3.65
36.5
83
18
4.37
43.7
60
25
5.47
54.7
50
30
6.56
65.6
41
36
7.87
78.7
30
50
9.84
98.4
0.63
6.3
0.76
7.6
1.05
10.5
1.26
12.6
1.58
15.8
1.90
19.0
2.63
26.3
3.16
31.6
3.79
37.9
4.74
47.4
5.69
56.9
6.82
68.2
8.53
85.3
25
60
10
100
20
75
10
100
16
90
10
100
15
100
10
100
12.5
120
10
100
10
150
10
100
8.3
180
10
100
Model
Motor/
Gearhead
50Hz
RATED TORQUE OF GEARHEAD
unit=above : N m / below : kgfcm
unit=above : N m / below : kgfcm
APPLICATION MODELPART No. L MOUNTING BOLT
DIMENSION TABLE
Black
White
Red
Black
Red
White
The direction of motor rotation is as viewed from the front shaft end of the motor
Gearhead and decimal gearhead are sold separately.
The code in of gearhead model is for gear ratio.
color indicates that the output shaft of the geared motor rotates in the same direction as the output shaft of the motor. Others indicate rotation in the opposite direction.
If you are to have less ratio than the ratio in the table, you can install the decimal gearhead, which has one tenth of the ratio, between the gearhead and the motor. In this case,
the permissible torque is 10N m/ 100kgfcm.
66 67
RatedTorque
(mN m)(gfcm)
Speed
(rpm)
Condenser
( )
StartingTorque
(mN m)(gfcm)
Current
(A)
Frequency
(Hz)
Voltage
(V)
60
60
110
1151.35
220
230
60
60
50
60
0.65
0.62
0.72
4104100
4104100
4504500
4104100
4004000
4004000
4704700
4004000
1550
1550
1250
1550
17
4.5
Output
(W)
single-phase
single-phase
REVERSIBLE MOTORS
60W LEAD WIRE TYPE
Model
K9RP60FUK9RS60FU
K9RP60FC
K9RS60FC
SPECIFICATIONS
CONNECTION DIAGRAMS
DIMENSIONS
30 minutes rating, four poles class E or A
GEARHEADS
DIMENSIONS
DECIMAL GEARHEAD GEARHEAD
APPLICATION MODELPART No. L MOUNTING BOLT
DIMENSION TABLE
RATED TORQUE OF GEARHEAD
Speed(rpm)
Ratio
600
3
500
3.6
360
5
300
6
240
7.5
200
9
144
12.5
120
15
100
18
72
25
60
30
50
36
36
50
30
60
24
75
20
90
18
100
15
120
12
150
10
180
Model
Motor/
Gearhead
60Hz
Speed(rpm)
Ratio
500
3
1.14
11.4
1.37
13.7
1.90
19.0
2.28
22.8
2.86
28.6
3.43
34.3
4.28
42.8
5.14
51.4
6.17
61.7
7.71
77.1
9.25
92.5
11.10
111.0
15.42
154.2
18.50
185.0
20
200
20
200
20
200
20
200
20
200
20
200
416
3.6
300
5
250
6
200
7.5
166
9
120
12.5
100
15
83
18
60
25
50
30
41
36
30
50
25
60
20
75
16
90
15
100
125
120
10
150
8.3
180
Model
Motor/
Gearhead
0.97
9.7
1.17
11.7
1.62
16.2
1.94
19.4
2.43
24.3
2.92
29.2
3.65
36.5
4.37
43.7
5.25
52.5
6.56
65.6
7.87
78.7
9.45
94.5
13.12
131.2
15.75
157.5
17.71
177.1
20
200
20
200
20
200
20
200
20
200
50Hzunit=above : N m / below : kgfcm
unit=above : N m / below : kgfcm
Black
White
Red
Black
Red
White
The direction of motor rotation is as viewed from the front shaft end of the motor
Gearhead and decimal gearhead are sold separately. The code in of gearhead model is for gear ratio.
color indicates that the output shaft of the geared motor rotates in the same direction as the output shaft of the motor. Others indicate rotation in the opposite direction.
If you are to have less ratio than the ratio in the table, you can install the decimal gearhead, which has one tenth of the ratio, between the gearhead and the motor. In this case,
the permissible torque is 20N m/ 200kgfcm.
68 69
REVERSIBLE MOTORS
90W LEAD WIRE TYPE
CONNECTION DIAGRAMS
DIMENSIONS
GEARHEADS
DIMENSIONS
DECIMAL GEARHEAD GEARHEAD
Speed(rpm)
Ratio
500
3
1.46
14.6
1.75
17.5
2.43
24.3
2.92
29.2
3.65
36.5
4.37
43.7
5.47
54.7
6.56
65.6
7.87
78.7
9.84
98.4
11.81
118.1
14.17
141.7
19.68
196.8
20
200
20
200
20
200
20
200
20
200
20
200
20
200
416
3.6
300
5
250
6
200
7.5
166
9
120
12.5
100
15
83
18
60
25
50
30
41
36
30
50
20
200
25
60
20
200
20
75
20
200
16
90
20
200
15
100
20
200
125
120
20
200
10
150
20
200
8.3
180
20
200
Model
Motor/
Gearhead
50Hz
RATED TORQUE OF GEARHEAD
unit=above : N m / below : kgfcm
RatedTorque
(mN m)(gfcm)
Speed
(rpm)
Condenser
( )
StartingTorque
(mN m)(gfcm)
Current
(A)
Frequency
(Hz)
Voltage
(V)
90
90
110
1152.20
220
230
60
60
50
60
1.10
1.20
1.10
6006000
6006000
7107100
6006000
5705700
6006000
7107100
6006000
1600
1550
1250
1550
25
7
Output
(W)
single-phase
single-phase
Model
K9RP90FU
K9RS90FU
K9RP90FC
K9RS90FC
SPECIFICATIONS
30 minutes rating, four poles class E or A
APPLICATION MODELPART No. L MOUNTING BOLT
DIMENSION TABLE
Speed(rpm)
Ratio
600
3
500
3.6
360
5
300
6
240
7.5
200
9
144
12.5
120
15
100
18
72
25
60
30
50
36
36
50
30
60
24
75
20
90
18
100
15
120
12
150
10
180
Model
Motor/
Gearhead
60Hzunit=above : N m / below : kgfcm
1.73
17.3
2.07
20.7
2.88
28.8
3.45
34.5
4.31
43.1
5.18
51.8
6.47
64.7
7.76
77.6
9.32
93.2
11.65
116.5
13.97
139.7
16.77
167.7
Black
White
Red
Black
Red
White
The direction of motor rotation is as viewed from the front shaft end of the motor
Gearhead and decimal gearhead are sold separately. The code in of gearhead model is for gear ratio.
color indicates that the output shaft of the geared motor rotates in the same direction as the output shaft of the motor. Others indicate rotation in the opposite direction.
If you are to have less ratio than the ratio in the table, you can install the decimal gearhead, which has one tenth of the ratio, between the gearhead and the motor. In this case,
the permissible torque is 20N m/200kgfcm.
70 71
GEARHEADS
DIMENSIONS
DECIMAL GEARHEAD GEARHEAD
RATED TORQUE OF GEARHEAD
APPLICATION MODELPART No. L MOUNTING BOLT
DIMENSION TABLE
APPLICATION MODELPART No. L MOUNTING BOLT
DIMENSION TABLE
GEARHEADS
DIMENSIONS
DECIMAL GEARHEAD GEARHEAD
Speed(rpm)
Ratio
500
3
416
3.6
300
5
250
6
200
7.5
166
9
120
12.5
100
15
83
18
60
25
50
30
41
36
30
50
25
60
20
75
16
90
15
100
13
120
10
150
8.3
180
Model
Motor/
Gearhead
50Hz
RATED TORQUE OF GEARHEAD
unit=above : N m / below : kgfcm
Speed(rpm)
Ratio
600
3
500
3.6
360
5
300
6
240
7.5
200
9
144
12.5
120
15
100
18
72
25
60
30
50
36
36
50
30
60
24
75
20
90
18
100
15
120
12
150
10
180
Model
Motor/
Gearhead
60Hzunit=above : N m / below : kgfcm
Speed(rpm)
Ratio
500
3
1.46
14.6
1.75
17.5
2.43
24.3
2.92
29.2
3.65
36.5
4.37
43.7
5.47
54.7
6.56
65.6
7.87
78.7
9.84
98.4
11.81
118.1
14.17
141.7
19.68
196.8
20
200
20
200
20
200
20
200
20
200
20
200
20
200
416
3.6
300
5
250
6
200
7.5
166
9
120
12.5
100
15
83
18
60
25
50
30
41
36
30
50
20
200
25
60
20
200
20
75
20
200
16
90
20
200
15
100
20
200
125
120
20
200
10
150
20
200
8.3
180
20
200
Model
Motor/
Gearhead
50Hzunit=above : N m / below : kgfcm
Speed(rpm)
Ratio
600
3
500
3.6
360
5
300
6
240
7.5
200
9
144
12.5
120
15
100
18
72
25
60
30
50
36
36
50
30
60
24
75
20
90
18
100
15
120
12
150
10
180
Model
Motor/
Gearhead
60Hzunit=above : N m / below : kgfcm
1.73
17.3
2.07
20.7
2.88
28.8
3.45
34.5
4.31
43.1
5.18
51.8
6.47
64.7
7.76
77.6
9.32
93.2
11.65
116.5
13.97
139.7
16.77
167.7
23.29
232.9
27.95
279.5
30
300
30
300
30
300
30
300
30
300
30
300
1.73
17.3
2.07
20.7
2.88
28.8
3.45
34.5
4.31
43.1
5.18
51.8
6.47
64.7
7.76
77.6
9.32
93.2
11.65
116.5
13.97
139.7
16.77
167.7
1.46
14.6
1.75
17.5
2.43
24.3
2.92
29.2
3.65
36.5
4.37
43.7
5.47
54.7
6.56
65.6
7.87
78.7
9.84
98.4
11.81
118.1
14.17
141.7
19.68
196.8
23.62
236.2
26.57
265.7
30
300
30
300
30
300
30
300
30
300
Gearhead and decimal gearhead are sold separately. The code in of gearhead model is for gear ratio.
color indicates that the output shaft of the geared motor rotates in the same direction as the output shaft of the motor. Others indicate rotation in the opposite direction.
If you are to have less ratio than the ratio in the table, you can install the decimal gearhead, which has one tenth of the ratio, between the gearhead and the motor. In this case,
the permissible torque is 20N m/ 200kgfcm.
Gearhead and decimal gearhead are sold separately. The code in of gearhead model is for gear ratio.
color indicates that the output shaft of the geared motor rotates in the same direction as the output shaft of the motor. Others indicate rotation in the opposite direction.
If you are to have less ratio than the ratio in the table, you can install the decimal gearhead, which has one tenth of the ratio, between the gearhead and the motor. In this case, the permissible torque is
30N m/300kgfcm.
TERMINAL BOX
INDUCTION MOTORS
75
1. Characteristic of Terminal Box Type Motor
The motor's charging section including lead wire is
made airtight by the terminal box to provide the
protection from the dust and moisture.
Therefore, the motor can be used in the harsh
environment.
The classification of the device protection structure for
our T type terminal box motor is IP54.
The motor features a compact design.
The ground terminal is attached to the motor.
However, Type (6~15W) of the single-phase induction
motor does not have a built-in ground inside the
terminal box.
Since the motor is so structured as to make the piping
work easier, it is excellent in connection work. The
cable is firmly fixed to provide the stronger tension
when wiring the cable.
The terminal box cover is made of PC resin which is
excellent in insulation and stiffness.
The T type terminal box uses a product that provides
high reliability.
Please use AWG NO. 24 ~ AWG NO. 10 (0.25 mm2
~ 4.0 mm2) for the lead wire. At this time, the length of
the peeled-off lead wire should be about 8mm.
2. Diagram of Terminal Box Structure
Terminal Block Box Type (T Type)
[Characteristic of Terminal Box Type Motor ]
(SINGLE-PHASE REVERSIBLE MOTOR)
(THREE-PHASE INDUCTION MOTOR)
(SINGLE-PHASE INDUCTION MOTOR)
Item Specification
InsulationResistance
Dielectric Strength
Temperature Rise
Insulation Class
Overheat ProtectionDevice
AmbientTemperature
100M or more when 500V megger is applied between the windings and the housing after rated motor operation under normal ambient temperature and humidity
Sufficient to withstand 1500V at 50/60Hz applied between thewindings and the case after rated motor operation under normalambient temperature and humidity for 1 min.
60 or less increase measured by
thermometer after rated operation
Class E (120 ), UL approval motor class A (105 )
Class E (120 ), UL approval motor class A (105 )
-10 ~ 50
85% maximum (non condensing)Ambient Humidity
3. GENERAL SPECIFICATION OF MOTORS
76 77
RatedTorque
(mN m)(gfcm)
Speed
(rpm)
Condenser
( )
StartingTorque
(mN m)(gfcm)
Current
(A)
Frequency
(Hz)
Voltage
(V)
6
6
110
115
220
230
60
60
50
60
0.19
0.11
0.12
0.11
40
400
40400
41410
40400
40
400
40400
48480
40400
1500
1500
1250
1500
2
0.6
Output
(W)
single-phase
single-phase
INDUCTION MOTORS
6W TERMINAL BOX TYPE
Model
K6IG6NU-T
K6IS6NU-T
K6IG6NC-T
K6IS6NC-T
SPECIFICATIONS
CONNECTION DIAGRAMS
DIMENSIONS
continuous rating, four poles class E or A
GEARHEADS
DIMENSIONS
DECIMAL GEARHEAD GEARHEAD
Speed(rpm)
Ratio
600
3
0.10
1.0
500
3.6
0.12
1.2
360
5
0.16
1.6
300
6
0.19
1.9
240
7.5
0.24
2.4
200
9
0.29
2.9
144
12.5
0.41
4.1
120
15
0.49
4.9
100
18
0.58
5.8
72
25
0.73
7.3
60
30
0.87
8.7
50
36
1.05
10.5
36
50
1.31
13.1
30
60
1.57
15.7
24
75
1.97
19.7
20
90
2.36
23.6
18
100
2.62
26.2
15
120
3
30
12
150
3
30
10
180
3
30
Model
Motor/
Gearhead
60Hz
Speed(rpm)
Ratio
500
3
0.12
1.2
416
3.6
0.14
1.4
300
5
0.19
1.9
250
6
0.23
2.3
200
7.5
0.29
2.9
166
9
0.35
3.5
120
12.5
0.49
4.9
100
15
0.58
5.8
83
18
0.70
7.0
60
25
0.87
8.7
50
30
1.05
10.5
41
36
1.26
12.6
30
50
1.57
15.7
25
60
1.89
18.9
20
75
2.36
23.6
16
90
2.83
28.3
15
100
3
30
125
120
3
30
10
150
3
30
8.3
180
3
30
Model
Motor/
Gearhead
50Hz
APPLICATION MODELPART No. L MOUNTING BOLT
DIMENSION TABLE
RATED TORQUE OF GEARHEAD
unit=above : N m / below : kgfcm
unit=above : N m / below : kgfcm
Black
White
Red
Black
Red
White
The direction of motor rotation is as viewed from the front shaft end of the motor
Gearhead and decimal gearhead are sold separately.
The code in of gearhead model is for gear ratio.
color indicates that the output shaft of the geared motor rotates in the same direction as the output shaft of the motor. Others indicate rotation in the opposite direction.
If you are to have less ratio than the ratio in the table, you can install the decimal gearhead, which has one tenth of the ratio, between the gearhead and the motor. In this case,
the permissible torque is 3N m/30kgfcm.
78 79
INDUCTION MOTORS
15W TERMINAL BOX TYPE
CONNECTION DIAGRAMS
DIMENSIONS
GEARHEADS
DIMENSIONS
DECIMAL GEARHEAD GEARHEAD
APPLICATION MODELPART No. L MOUNTING BOLT
DIMENSION TABLE
RatedTorque
(mN m)(gfcm)
Speed
(rpm)
Condenser
( )
StartingTorque
(mN m)(gfcm)
Current
(A)
Frequency
(Hz)
Voltage
(V)
15
15
110
115
220
230
60
60
50
60
0.36
0.37
0.18
65
650
65650
75750
65650
100
1000
1001000
1201200
1001000
1500
1500
1250
1500
4.5
1
Output
(W)
single-phase
single-phase
Model
K7IG15NU-T
K7IS15NU-T
K7IG15NC-T
K7IS15NC-T
SPECIFICATIONS
continuous rating, four poles class E or A
RATED TORQUE OF GEARHEAD
50Hzunit=above : N m / below : kgfcm
Speed(rpm)
Ratio
600
3
0.24
2.4
500
3.6
0.29
2.9
360
5
0.41
4.1
300
6
0.49
4.9
240
7.5
0.61
6.1
200
9
0.73
7.3
144
12.5
1.01
10.1
120
15
1.22
12.2
100
18
1.46
14.6
72
25
1.82
18.2
60
30
2.19
21.9
50
36
2.62
26.2
36
50
3.28
32.8
30
60
3.94
39.4
24
75
4.92
49.2
20
90
5
50
18
100
5
50
15
120
5
50
12
150
5
50
10
180
5
50
Model
Motor/
Gearhead
60Hz
Speed(rpm)
Ratio
500
3
0.29
2.9
416
3.6
0.35
3.5
300
5
0.49
4.9
250
6
0.58
5.8
200
7.5
0.73
7.3
166
9
0.87
8.7
120
12.5
1.22
12.2
100
15
1.46
14.6
83
18
1.75
17.5
60
25
2.19
21.9
50
30
2.62
26.2
41
36
3.15
31.5
30
50
3.94
39.4
25
60
4.72
47.2
20
75
5
50
16
90
5
50
15
100
5
50
125
120
5
50
10
150
5
50
8.3
180
5
50
Model
Motor/
Gearhead
unit=above : N m / below : kgfcm
Black
White
Red
Black
Red
White
The direction of motor rotation is as viewed from the front shaft end of the motor
Gearhead and decimal gearhead are sold separately.
The code in of gearhead model is for gear ratio.
color indicates that the output shaft of the geared motor rotates in the same direction as the output shaft of the motor. Others indicate rotation in the opposite direction.
If you are to have less ratio than the ratio in the table, you can install the decimal gearhead, which has one tenth of the ratio, between the gearhead and the motor. In this case,
the permissible torque is 5N m/ 50kgfcm.
80 81
INDUCTION MOTORS
25W TERMINAL BOX TYPE
CONNECTION DIAGRAMS
DIMENSIONS
GEARHEADS
DIMENSIONS
DECIMAL GEARHEAD GEARHEAD
RatedTorque
(mN m)(gfcm)
Speed
(rpm)
Condenser
( F)
StartingTorque
(mN m)(gfcm)
Current
(A)
Frequency
(Hz)
Voltage
(V)
25
25
25
115
11060 0.50
1200
120
1600
1601500 5
220
230
220
230
60
50
60
60
50
0.26
0.28
0.27
0.36
0.31
1201200
1201200
1201200
1601600
2402400
1601600
1901900
1601600
1601600
1901900
1550
1300
1550
1600
1350
60 0.271601600
1601600
1600
1.5
-
Output
(W)
single-phase
single-phase
Model
K8IG25NC-T
K8IG25NU-T
K8IS25NU-T
K8IS25NC-T
K8IG25NH-T
K8IS25NH-T
SPECIFICATIONS
continuous rating, four poles class E or A
APPLICATION MODELPART No. L MOUNTING BOLT
DIMENSION TABLE
RATED TORQUE OF GEARHEAD
Speed(rpm)
Ratio
600
3
500
3.6
360
5
300
6
240
7.5
200
9
144
12.5
120
15
100
18
72
25
60
30
50
36
36
50
30
60
24
75
20
90
18
100
15
120
12
150
10
180
Model
Motor/
Gearhead
60Hz
Speed(rpm)
Ratio
500
3
0.46
4.6
0.55
5.5
0.77
7.7
0.92
9.2
1.15
11.5
1.39
13.9
1.92
19.2
2.31
23.1
2.77
27.7
3.46
34.6
4.16
41.6
4.99
49.9
6.23
62.3
7.48
74.8
0.46
4.6
0.55
5.5
0.77
7.7
0.92
9.2
1.15
11.5
1.39
13.9
1.92
19.2
2.31
23.1
2.77
27.7
3.46
34.6
4.16
41.6
4.99
49.9
6.23
62.3
7.48
74.8
8
80
8
80
8
80
8
80
8
80
8
80
8
80
8
80
8
80
8
80
8
80
8
80
416
3.6
300
5
250
6
200
7.5
166
9
120
12.5
100
15
83
18
60
25
50
30
41
36
30
50
25
60
20
75
16
90
15
100
125
120
10
150
8.3
180
Model
Motor/
Gearhead
0.39
3.9
0.39
3.9
0.47
4.7
0.47
4.7
0.65
6.5
0.65
6.5
0.78
7.8
0.78
7.8
0.97
9.7
0.97
9.7
1.62
16.2
1.62
16.2
1.94
19.4
1.94
19.4
2.33
23.3
2.33
23.3
1.17
11.7
1.17
11.7
2.92
29.2
2.92
29.2
3.50
35.0
3.50
35.0
4.20
42.0
4.20
42.0
5.25
52.5
5.25
52.5
6.30
63.0
6.30
63.0
7.87
78.7
7.87
78.7
8
80
8
80
8
80
8
80
8
80
8
80
8
80
8
80
8
80
8
80
50Hzunit=above : N m / below : kgfcm
unit=above : N m / below : kgfcm
Black
White
Red
Black
Red
White
The direction of motor rotation is as viewed from the front shaft end of the motor
Gearhead and decimal gearhead are sold separately.
The code in of gearhead model is for gear ratio.
color indicates that the output shaft of the geared motor rotates in the same direction as the output shaft of the motor. Others indicate rotation in the opposite direction.
If you are to have less ratio than the ratio in the table, you can install the decimal gearhead, which has one tenth of the ratio, between the gearhead and the motor. In this case,
the permissible torque is 8N m/80kgfcm. How ever, When 1/25~1/36 gearhead is installed, the torque is 6N m/60kgfcm.
82 83
INDUCTION MOTORS
40W TERMINAL BOX TYPE
CONNECTION DIAGRAMS
DIMENSIONS
GEARHEADS
DIMENSIONS
DECIMAL GEARHEAD GEARHEAD
RATED TORQUE OF GEARHEAD
SPECIFICATIONS
K9IG40NC-T
K9IG40NU-TK9IS40NU-T
K9IS40NC-T
K9IG40NH-T
K9IS40NH-T
APPLICATION MODELPART No. L MOUNTING BOLT
DIMENSION TABLE
RatedTorque
(mN m)(gfcm)
Speed
(rpm)
Condenser
( F)
StartingTorque
(mN m)(gfcm)
Current
(A)
Frequency
(Hz)
Voltage
(V)
40
40
40
220
115
110
60
50
60 0.89
0.42
0.442402400
2102100
2102100
2602600
3003000
2602600
1500
1300 2.5
81500
230
220
230
60
60
0.44
0.33
2102100
7107100
2602600
2502500
1500
1600
50 0.39 9009000
3003000
1300
60 0.337107100
2502500
1600
-
Output
(W)Model
Speed(rpm)
Ratio
600
3
0.63
6.3
500
3.6
0.76
7.6
360
5
1.05
10.5
300
6
1.26
12.6
240
7.5
1.58
15.8
200
9
1.90
19.0
144
12.5
2.63
26.3
120
15
3.16
31.6
100
18
3.79
37.9
72
25
4.74
47.4
60
30
5.69
56.9
50
36
6.82
68.2
36
50
8.53
85.3
30
60
10
100
24
75
10
100
20
90
10
100
18
100
10
100
15
120
10
100
12
150
10
100
10
180
10
100
Model
Motor/
Gearhead
0.61
6.1
0.73
7.3
1.01
10.1
1.22
12.2
1.52
15.2
1.82
18.2
2.53
25.3
3.04
30.4
3.65
36.5
4.56
45.6
5.47
54.7
6.56
65.6
8.20
82.0
9.84
98.4
10
100
10
100
10
100
10
100
10
100
10
100
60Hz
Speed(rpm)
Ratio
500
3
0.73
7.3
416
3.6
0.87
8.7
300
5
1.22
12.2
250
6
1.46
14.6
200
7.5
1.82
18.2
166
9
2.19
21.9
120
12.5
3.04
30.4
100
15
3.65
36.5
83
18
4.37
43.7
60
25
5.47
54.7
50
30
6.56
65.6
41
36
7.87
78.7
30
50
9.84
98.4
0.73
7.3
0.87
8.7
1.22
12.2
1.46
14.6
1.82
18.2
2.19
21.9
3.04
30.4
3.65
36.5
4.37
43.7
5.47
54.7
6.56
65.6
7.87
78.7
9.84
98.4
25
60
10
100
20
75
10
100
16
90
10
100
15
100
10
100
125
120
10
100
10
150
10
100
8.3
180
10
100
Model
Motor/
Gearhead
10
100
10
100
10
100
10
100
10
100
10
100
10
100
50Hz
Gearhead and decimal gearhead are sold separately.
The code in of gearhead model is for gear ratio.
color indicates that the output shaft of the geared motor rotates in the same direction as the output shaft of the motor. Others indicate rotation in the opposite direction.
If you are to have less ratio than the ratio in the table, you can install the decimal gearhead, which has one tenth of the ratio, between the gearhead and the motor.
In this case, the permissible torque is 10N m/100kgfcm.
Black
White
Red
Black
Red
White
The direction of motor rotation is as viewed from the front shaft end of the motor
84 85
INDUCTION MOTORS
60W TERMINAL BOX TYPE
CONNECTION DIAGRAMS
DIMENSIONS
GEARHEADS
DIMENSIONS
DECIMAL GEARHEAD GEARHEAD
SPECIFICATIONS
K9IP60FC-T
K9IP60FU-TK9IS60FU-T
K9IS60FC-T
K9IP60FH-T
K9IS60FH-T
APPLICATION MODELPART No. L MOUNTING BOLT
DIMENSION TABLE
RATED TORQUE OF GEARHEAD
RatedTorque
(mN m)(gfcm)
Speed
(rpm)
Condenser
( F)
StartingTorque
(mN m)(gfcm)
Current
(A)
Frequency
(Hz)
Voltage
(V)
60
60
60
230
220
115
110
60
50
60 1.30
0.60
0.623903900
3503500
3503500
4004000
4704700
4004000
1550
1250 4
161550
220
60
60
0.62
0.48
3503500
145014500
4004000
3703700
1550
1600
23050
60
0.60
0.49
115011500
145014500
4604600
3703700
1350
1600
-
Output
(W)Model
Speed(rpm)
Ratio
600
3
500
3.6
360
5
300
6
240
7.5
200
9
144
12.5
120
15
100
18
72
25
60
30
50
36
36
50
30
60
24
75
20
90
18
100
15
120
12
150
10
180
Model
Motor/
Gearhead
60Hz
Speed(rpm)
Ratio
500
3
1.14
11.4
1.12
11.2
1.37
13.7
1.34
13.4
1.9
19.0
1.86
18.6
2.28
22.8
2.24
22.4
2.86
28.6
2.79
27.9
3.43
34.3
3.35
33.5
4.28
42.8
4.19
41.9
5.14
51.4
5.03
50.3
6.17
61.7
6.04
60.4
7.71
77.1
7.55
75.5
9.25
92.5
9.05
90.5
11.10
111.0
10.87
108.7
15.42
154.2
15.09
150.9
18.50
185.0
18.11
181.1
20
200
20
200
20
200
20
200
20
200
20
200
20
200
20
200
20
200
20
200
20
200
20
200
416
3.6
300
5
250
6
200
7.5
166
9
120
12.5
100
15
83
18
60
25
50
30
41
36
30
50
25
60
20
75
16
90
15
100
125
120
10
150
8.3
180
Model
Motor/
Gearhead
0.97
9.7
0.90
9.0
1.17
11.7
1.08
10.8
1.62
16.2
1.50
15.0
1.94
19.4
1.80
18.0
2.43
24.3
2.25
22.5
2.92
29.2
2.70
27.0
3.65
36.5
3.37
33.7
4.37
43.7
4.05
40.5
5.25
52.5
4.86
48.6
6.56
65.6
6.07
60.7
7.87
78.7
7.28
72.8
9.45
94.5
8.74
87.4
13.12
131.2
12.14
121.4
15.75
157.5
14.57
145.7
17.71
177.1
16.39
163.9
20
200
19.66
196.6
20
200
20
200
20
200
20
200
20
200
20
200
20
200
20
200
50Hzunit=above : N m / below : kgfcm
unit=above : N m / below : kgfcm
Gearhead and decimal gearhead are sold separately.
The code in of gearhead model is for gear ratio.
color indicates that the output shaft of the geared motor rotates in the same direction as the output shaft of the motor. Others indicate rotation in the opposite direction.
If you are to have less ratio than the ratio in the table, you can install the decimal gearhead, which has one tenth of the ratio, between the gearhead and the motor. In this case,
the permissible torque is20N m/200kgfcm.
Black
White
Red
Black
Red
White
The direction of motor rotation is as viewed from the front shaft end of the motor
86 87
INDUCTION MOTORS
90W TERMINAL BOX TYPE
SPECIFICATIONS
CONNECTION DIAGRAMS
DIMENSIONS
GEARHEADS
DIMENSIONS
DECIMAL GEARHEAD GEARHEAD
K9IP90FC-T
K9IP90FU-T
K9IS90FU-T
K9IS90FC-T
K9IP90FH-T
K9IS90FH-T
APPLICATION MODELPART No. L MOUNTING BOLT
DIMENSION TABLE
RATED TORQUE OF GEARHEAD
RatedTorque
(mN m)(gfcm)
Speed
(rpm)
Condenser
( )
StartingTorque
(mN m)(gfcm)
Current
(A)
Frequency
(Hz)
Voltage
(V)
90
90
90
220
115
110
60
50
60 2.00
0.90
1.05
5005000
5505500
6006000
5000
500
5700
570
7107100
5705700
1600
1300 6
201600
230
220
60
60
1.00
0.68160016000
5705700
5505500
1600
1600
23050
60
0.85
0.71
205020500
160016000
6806800
5505500
1350
1600
-
Output
(W)
single-phase
single-phase
three-phase
Model
Speed(rpm)
Ratio
600
3
500
3.6
360
5
300
6
240
7.5
200
9
144
12.5
120
15
100
18
72
25
60
30
50
36
36
50
30
60
24
75
20
90
18
100
15
120
12
150
10
180
Model
Motor/
Gearhead
60Hz
Speed(rpm)
Ratio
500
3
1.73
17.3
1.65
16.5
2.07
20.7
1.98
19.8
2.88
28.8
2.75
27.5
3.45
34.5
3.30
33.0
4.31
43.1
4.13
41.3
5.18
51.8
4.96
49.6
6.47
64.7
6.20
62.0
7.76
77.6
7.44
74.4
9.32
93.2
8.92
89.2
11.65
116.5
11.15
111.5
13.97
139.7
13.38
133.8
16.77
167.7
16.06
160.6
20
200
20
200
20
200
20
200
20
200
20
200
20
200
20
200
20
200
20
200
20
200
20
200
20
200
20
200
20
200
20
200
416
3.6
300
5
250
6
200
7.5
166
9
120
12.5
100
15
83
18
60
25
50
30
41
36
30
50
25
60
20
75
16
90
15
100
125
120
10
150
8.3
180
Model
Motor/
Gearhead
1.39
13.9
1.34
13.4
1.66
16.6
1.60
16.0
2.31
23.1
2.23
22.3
2.77
27.7
2.67
26.7
3.46
34.6
3.34
33.4
4.16
41.6
4.01
40.1
5.19
51.9
5.57
55.7
6.23
62.3
6.68
66.8
7.48
74.8
8.02
80.2
9.35
93.5
10.02
100.2
11.22
112.2
12.03
120.3
13.46
134.6
14.43
144.3
18.70
187.0
18.04
180.4
20
200
20
200
20
200
20
200
20
200
20
200
20
200
20
200
20
200
20
200
20
200
20
200
20
200
20
200
50Hz unit=above : N m / below : kgfcm
unit=above : N m / below : kgfcm
Black
White
Red
Black
Red
White
The direction of motor rotation is as viewed from the front shaft end of the motor
Gearhead and decimal gearhead are sold separately. The code in of gearhead model is for gear ratio.
color indicates that the output shaft of the geared motor rotates in the same direction as the output shaft of the motor. Others indicate rotation in the opposite direction.
If you are to have less ratio than the ratio in the table, you can install the decimal gearhead, which has one tenth of the ratio, between the gearhead and the motor. In this case,
the permissible torque is 20N m/200kgfcm.
88 89
GEARHEADS
DIMENSIONS
DECIMAL GEARHEAD GEARHEAD
APPLICATION MODELPART No. L MOUNTING BOLT
DIMENSION TABLE
APPLICATION MODELPART No. L MOUNTING BOLT
DIMENSION TABLE
RATED TORQUE OF GEARHEAD
GEARHEADS
DIMENSIONS
DECIMAL GEARHEAD GEARHEAD
Speed(rpm)
Ratio
600
3
500
3.6
360
5
300
6
240
7.5
200
9
144
12.5
120
15
100
18
72
25
60
30
50
36
36
50
30
60
24
75
20
90
18
100
15
120
12
150
10
180
Model
Motor/
Gearhead
60Hz
Speed(rpm)
Ratio
500
3
416
3.6
300
5
250
6
200
7.5
166
9
120
12.5
100
15
83
18
60
25
50
30
41
36
30
50
25
60
20
75
16
90
15
100
125
120
10
150
8.3
180
Model
Motor/
Gearhead
50Hz
RATED TORQUE OF GEARHEAD
unit=above : N m / below : kgfcm
unit=above : N m / below : kgfcm
Speed(rpm)
Ratio
600
3
500
3.6
360
5
300
6
240
7.5
200
9
144
12.5
120
15
100
18
72
25
60
30
50
36
36
50
30
60
24
75
20
90
18
100
15
120
12
150
10
180
Model
Motor/
Gearhead
60Hz
Speed(rpm)
Ratio
500
3
1.73
17.3
1.65
16.5
2.07
20.7
1.98
19.8
2.88
28.8
2.75
27.5
3.45
34.5
3.30
33.0
4.31
43.1
4.13
41.3
5.18
51.8
4.96
49.6
6.47
64.7
6.20
62.0
7.76
77.6
7.44
74.4
9.32
93.2
8.92
89.2
11.65
116.5
11.15
111.5
13.97
139.7
13.38
133.8
16.77
167.7
16.06
160.6
20
200
20
200
20
200
20
200
20
200
20
200
20
200
20
200
20
200
20
200
20
200
20
200
20
200
20
200
20
200
20
200
416
3.6
300
5
250
6
200
7.5
166
9
120
12.5
100
15
83
18
60
25
50
30
41
36
30
50
25
60
20
75
16
90
15
100
12.5
120
10
150
8.3
180
Model
Motor/
Gearhead
1.39
13.9
1.34
13.4
1.66
16.6
1.60
16.0
2.31
23.1
2.23
22.3
2.77
27.7
2.67
26.7
3.46
34.6
3.34
33.4
4.16
41.6
4.01
40.1
5.19
51.9
5.01
50.1
6.23
62.3
6.01
60.1
7.48
74.8
7.22
72.2
9.35
93.5
9.02
90.2
11.22
112.2
10.83
108.3
13.46
134.6
12.99
129.9
18.70
187.0
18.04
180.4
20
200
20
200
20
200
20
200
20
200
20
200
20
200
20
200
20
200
20
200
20
200
20
200
20
200
20
200
50Hzunit=above : N m / below : kgfcm
unit=above : N m / below : kgfcm
1.73
17.3
1.65
16.5
2.07
20.7
1.98
19.8
2.88
28.8
2.75
27.5
3.45
34.5
3.30
33.0
4.31
43.1
4.13
41.3
5.18
51.8
4.96
49.6
6.47
64.7
6.20
62.0
7.76
77.6
7.44
74.4
9.32
93.2
8.92
89.2
11.65
116.5
11.15
111.5
13.97
139.7
13.38
133.8
16.77
167.7
16.06
160.6
23.29
232.9
22.31
223.1
27.95
279.5
26.77
267.7
30
300
30
200
30
300
30
200
30
300
30
300
30
300
30
300
30
300
30
300
30
300
30
300
1.39
13.9
1.34
13.4
1.66
16.6
1.60
16.0
2.31
23.1
2.23
22.3
2.77
27.7
2.67
26.7
3.46
34.6
3.34
33.4
4.16
41.6
4.01
40.1
5.19
51.9
5.01
50.1
6.23
62.3
6.01
60.1
7.48
74.8
7.22
72.2
9.35
93.5
9.02
90.2
11.22
112.2
10.83
108.3
13.46
134.6
12.99
129.9
18.70
187.0
18.04
180.4
22.44
224.4
21.65
216.5
25.24
252.4
24.36
243.6
30
300
29.23
292.3
30
200
30
300
30
300
30
300
30
300
30
300
30
300
30
300
Gearhead and decimal gearhead are sold separately. The code in of gearhead model is for gear ratio.
color indicates that the output shaft of the geared motor rotates in the same direction as the output shaft of the motor. Others indicate rotation in the opposite direction.
If you are to have less ratio than the ratio in the table, you can install the decimal gearhead, which has one tenth of the ratio, between the gearhead and the motor. In this case,
the permissible torque is 20N m/ 200kgfcm.
Gearhead and decimal gearhead are sold separately. The code in of gearhead model is for gear ratio.
color indicates that the output shaft of the geared motor rotates in the same direction as the output shaft of the motor. Others indicate rotation in the opposite direction.
If you are to have less ratio than the ratio in the table, you can install the decimal gearhead, which has one tenth of the ratio, between the gearhead and the motor. In this case,
the permissible torque is 30N m/ 300kgfcm.
TERMINAL BOX
REVERSIBLE MOTORS
92 93
RatedTorque
(mN m)(gfcm)
Speed
(rpm)
Condenser
( )
StartingTorque
(mN m)(gfcm)
Current
(A)
Frequency
(Hz)
Voltage
(V)
6
6
110
115
220
230
60
60
50
60
0.22
0.13
50
500
50500
52520
50500
40
400
40400
48480
40400
1500
1500
1250
1500
2.5
0.8
Output
(W)
single-phase
single-phase
REVERSIBLE MOTORS
6W TERMINAL BOX TYPE
Model
K6RG6NU-T
K6RS6NU-T
K6RG6NC-T
K6RS6NC-T
SPECIFICATIONS
CONNECTION DIAGRAMS
DIMENSIONS
30 minutes rating, four poles class E or A
GEARHEADS
DIMENSIONS
DECIMAL GEARHEAD GEARHEAD
APPLICATION MODELPART No. L MOUNTING BOLT
DIMENSION TABLE
RATED TORQUE OF GEARHEAD
Speed(rpm)
Ratio
600
3
0.10
1.0
500
3.6
0.12
1.2
360
5
0.16
1.6
300
6
0.19
1.9
240
7.5
0.24
2.4
200
9
0.29
2.9
144
12.5
0.41
4.1
120
15
0.49
4.9
100
18
0.58
5.8
72
25
0.73
7.3
60
30
0.87
8.7
50
36
1.05
10.5
36
50
1.31
13.1
30
60
1.57
15.7
24
75
1.97
19.7
20
90
2.36
23.6
18
100
2.62
26.2
15
120
3
30
12
150
3
30
10
180
3
30
Model
Motor/
Gearhead
60Hz
Speed(rpm)
Ratio
500
3
0.12
1.2
416
3.6
0.14
1.4
300
5
0.19
1.9
250
6
0.23
2.3
200
7.5
0.29
2.9
166
9
0.35
3.5
120
12.5
0.49
4.9
100
15
0.58
5.8
83
18
0.70
7.0
60
25
0.87
8.7
50
30
1.05
10.5
41
36
1.26
12.6
30
50
1.57
15.7
25
60
1.89
18.9
20
75
2.36
2.36
16
90
2.83
28.3
15
100
3
30
125
120
3
30
10
150
3
30
8.3
180
3
30
Model
Motor/
Gearhead
50Hzunit=above : N m / below : kgfcm
unit=above : N m / below : kgfcm
Black
White
Red
Black
Red
White
The direction of motor rotation is as viewed from the front shaft end of the motor
Gearhead and decimal gearhead are sold separately.
The code in of gearhead model is for gear ratio.
color indicates that the output shaft of the geared motor rotates in the same direction as the output shaft of the motor. Others indicate rotation in the opposite direction.
If you are to have less ratio than the ratio in the table, you can install the decimal gearhead, which has one tenth of the ratio, between the gearhead and the motor. In this case,
the permissible torque is 3N m/30kgfcm.
94 95
RatedTorque
(mN m)(gfcm)
Speed
(rpm)
Condenser
( )
StartingTorque
(mN m)(gfcm)
Current
(A)
Frequency
(Hz)
Voltage
(V)
15
15
110
115
220
230
60
60
50
60
0.42
0.41
0.21
100
1000
100
1000
100
1000
1001000
1201200
1001000
1500
1500
1250
1500
6
1.5
Output
(W)
single-phase
single-phase
REVERSIBLE MOTORS
15W TERMINAL BOX TYPE
Model
K7RG15NU-T
K7RS15NU-T
K7RG15NC-T
K7RS15NC-T
SPECIFICATIONS
CONNECTION DIAGRAMS
DIMENSIONS
GEARHEADS
DIMENSIONS
DECIMAL GEARHEAD GEARHEAD
RATED TORQUE OF GEARHEAD
APPLICATION MODELPART No. L MOUNTING BOLT
DIMENSION TABLE
50Hzunit=above : N m / below : kgfcm
Speed(rpm)
Ratio
600
3
0.24
2.4
500
3.6
0.29
2.9
360
5
0.41
4.1
300
6
0.49
4.9
240
7.5
0.61
6.1
200
9
0.73
7.3
144
12.5
1.01
10.1
120
15
1.22
12.2
100
18
1.46
14.6
72
25
1.82
18.2
60
30
2.19
21.9
50
36
2.62
26.2
36
50
3.28
32.8
30
60
3.94
39.4
24
75
4.92
49.2
20
90
5
50
18
100
5
50
15
120
5
50
12
150
5
50
10
180
5
50
Model
Motor/
Gearhead
60Hz
Speed(rpm)
Ratio
500
3
0.29
2.9
416
3.6
0.35
3.5
300
5
0.49
4.9
250
6
0.58
5.8
200
7.5
0.73
7.3
166
9
0.87
8.7
120
12.5
1.22
12.2
100
15
1.46
14.6
83
18
1.75
17.5
60
25
2.19
21.9
50
30
2.62
26.2
41
36
3.15
31.5
30
50
3.94
39.4
25
60
4.72
47.2
20
75
5
50
16
90
5
50
15
100
5
50
125
120
5
50
10
150
5
50
8.3
180
5
50
Model
Motor/
Gearhead
unit=above : N m / below : kgfcm
Black
White
Red
Black
Red
White
The direction of motor rotation is as viewed from the front shaft end of the motor
Gearhead and decimal gearhead are sold separately.
The code in of gearhead model is for gear ratio.
color indicates that the output shaft of the geared motor rotates in the same direction as the output shaft of the motor. Others indicate rotation in the opposite direction.
If you are to have less ratio than the ratio in the table, you can install the decimal gearhead, which has one tenth of the ratio, between the gearhead and the motor. In this case,
the permissible torque is 5N m/ 50kgfcm.
96 97
RatedTorque
(mN m)(gfcm)
Speed
(rpm)
Condenser
( )
StartingTorque
(mN m)(gfcm)
Current
(A)
Frequency
(Hz)
Voltage
(V)
25
25
110
115
220
230
60
60
50
60
0.56
0.33
0.30
0.34
130
1300
1301300
1501500
1301300
200
2000
2002000
2352350
2002000
1500
1500
1250
1500
6
2
Output
(W)
single-phase
single-phase
REVERSIBLE MOTORS
25W TERMINAL BOX TYPE
Model
K8RG25NU-T
K8RS25NU-T
K8RG25NC-T
K8RS25NC-T
SPECIFICATIONS
CONNECTION DIAGRAMS
DIMENSIONS
30 minutes rating, four poles class E or A
GEARHEADS
DIMENSIONS
DECIMAL GEARHEAD GEARHEAD
RATED TORQUE OF GEARHEAD
APPLICATION MODELPART No. L MOUNTING BOLT
DIMENSION TABLE
Speed(rpm)
Ratio
600
3
0.49
4.9
500
3.6
0.58
5.8
360
5
0.81
8.1
300
6
0.97
9.7
240
7.5
1.22
12.2
200
9
1.46
14.6
144
12.5
2.03
20.3
120
15
2.43
24.3
100
18
2.92
29.2
72
25
3.65
36.5
60
30
4.37
43.7
50
36
5.25
52.5
36
50
6.56
65.6
30
60
7.87
78.7
24
75
8
80
20
90
8
80
18
100
8
80
15
120
8
80
12
150
8
80
10
180
8
80
Model
Motor/
Gearhead
60Hz
Speed(rpm)
Ratio
500
3
0.57
5.7
416
3.6
0.69
6.9
300
5
0.95
9.5
250
6
1.14
11.4
200
7.5
1.43
14.3
166
9
1.71
17.1
120
12.5
2.38
23.8
100
15
2.86
28.6
83
18
3.43
34.3
60
25
4.28
42.8
50
30
5.14
51.4
41
36
6.17
61.7
30
50
7.71
77.1
25
60
8
80
20
75
8
80
16
90
8
80
15
100
8
80
125
120
8
80
10
150
8
80
8.3
180
8
80
Model
Motor/
Gearhead
50Hzunit=above : N m / below : kgfcm
unit=above : N m / below : kgfcm
Black
White
Red
Black
Red
White
The direction of motor rotation is as viewed from the front shaft end of the motor
Gearhead and decimal gearhead are sold separately. The code in of gearhead model is for gear ratio.
color indicates that the output shaft of the geared motor rotates in the same direction as the output shaft of the motor. Others indicate rotation in the opposite direction.
If you are to have less ratio than the ratio in the table, you can install the decimal gearhead, which has one tenth of the ratio, between the gearhead and the motor. In this case,
the permissible torque is 8N m/80kgfcm. But, if you install 1/25~1/36 gearhead, the permissible torque is 6N m/60kgfcm.
98 99
REVERSIBLE MOTORS
40W TERMINAL BOX TYPE
SPECIFICATIONS
CONNECTION DIAGRAMS
DIMENSIONS
30 minutes rating, four poles class E or A
GEARHEADS
DIMENSIONS
DECIMAL GEARHEAD GEARHEAD
RATED TORQUE OF GEARHEAD
RatedTorque
(mN m)(gfcm)
Speed
(rpm)
Condenser
( )
StartingTorque
(mN m)(gfcm)
Current
(A)
Frequency
(Hz)
Voltage
(V)
40
40
230
220
115
110
60
50
60 0.83
0.55
0.423203200
3003000
3000
300
2600
260
3003000
2602600
1500
1300 3.5
101500
60 0.563003000
2602600 1500
Output
(W)
single-phase
single-phase
Model
K9RG40NC-T
K9RG40NU-T
K9RS40NU-T
K9RS40NC-T
APPLICATION MODELPART No. L MOUNTING BOLT
DIMENSION TABLE
Speed(rpm)
Ratio
600
3
500
3.6
360
5
300
6
240
7.5
200
9
144
12.5
120
15
100
18
72
25
60
30
50
36
36
50
30
60
10
100
24
75
10
100
20
90
10
100
18
100
10
100
15
120
10
100
12
150
10
100
10
180
10
100
Model
Motor/
Gearhead
60Hz
Speed(rpm)
Ratio
500
3
0.73
7.3
416
3.6
0.87
8.7
300
5
1.22
12.2
250
6
1.46
14.6
200
7.5
1.82
18.2
166
9
2.19
21.9
120
12.5
3.04
30.4
100
15
3.65
36.5
83
18
4.37
43.7
60
25
5.47
54.7
50
30
6.56
65.6
41
36
7.87
78.7
30
50
9.84
98.4
0.63
6.3
0.76
7.6
1.05
10.5
1.26
12.6
1.58
15.8
1.90
19.0
2.63
26.3
3.16
31.6
3.79
37.9
4.74
47.4
5.69
56.9
6.82
68.2
8.53
85.3
25
60
10
100
20
75
10
100
16
90
10
100
15
100
10
100
125
120
10
100
10
150
10
100
8.3
180
10
100
Model
Motor/
Gearhead
50Hzunit=above : N m / below : kgfcm
unit=above : N m / below : kgfcm
Black
White
Red
Black
Red
White
The direction of motor rotation is as viewed from the front shaft end of the motor
Gearhead and decimal gearhead are sold separately. The code in of gearhead model is for gear ratio.
color indicates that the output shaft of the geared motor rotates in the same direction as the output shaft of the motor. Others indicate rotation in the opposite direction.
If you are to have less ratio than the ratio in the table, you can install the decimal gearhead, which has one tenth of the ratio, between the gearhead and the motor. In this case,
the permissible torque is 10N m/ 100kgfcm.
100 101
REVERSIBLE MOTORS
60W TERMINAL BOX TYPE
SPECIFICATIONS
CONNECTION DIAGRAMS
DIMENSIONS
30 minutes rating, four poles class E or A
GEARHEADS
DIMENSIONS
DECIMAL GEARHEAD GEARHEAD
RATED TORQUE OF GEARHEAD
RatedTorque
(mN m)(gfcm)
Speed
(rpm)
Condenser
( )
StartingTorque
(mN m)(gfcm)
Current
(A)
Frequency
(Hz)
Voltage
(V)
60
60
230
220
115
110
60
50
60 1.35
0.65
4504500
4104100
4100
410
4000
400
4704700
4004000
1550
1250 4.5
171550
60
0.62
0.724104100
4004000 1550
Output
(W)
single-phase
single-phase
Model
K9RP60FC-T
K9RP60FU-T
K9RS60FU-T
K9RS60FC-T
APPLICATION MODELPART No. L MOUNTING BOLT
DIMENSION TABLE
Speed(rpm)
Ratio
600
3
500
3.6
360
5
300
6
240
7.5
200
9
144
12.5
120
15
100
18
72
25
60
30
50
36
36
50
30
60
24
75
20
90
18
100
15
120
12
150
10
180
Model
Motor/
Gearhead
60Hz
Speed(rpm)
Ratio
500
3
1.14
11.4
1.37
13.7
1.90
19.0
2.28
22.8
2.86
28.6
3.43
34.3
4.28
42.8
5.14
51.4
6.17
61.7
7.71
77.1
9.25
92.5
11.10
111.0
15.42
154.2
18.50
185.0
20
200
20
200
20
200
20
200
20
200
20
200
416
3.6
300
5
250
6
200
7.5
166
9
120
12.5
100
15
83
18
60
25
50
30
41
36
30
50
25
60
20
75
16
90
15
100
125
120
10
150
8.3
180
Model
Motor/
Gearhead
0.97
9.7
1.17
11.7
1.62
16.2
1.94
19.4
2.43
24.3
2.92
29.2
3.65
36.5
4.37
43.7
5.25
52.5
6.56
65.6
7.87
78.7
9.45
94.5
13.12
131.2
15.75
157.5
17.71
177.1
20
200
20
200
20
200
20
200
20
200
50Hzunit=above : N m / below : kgfcm
unit=above : N m / below : kgfcm
Black
White
Red
Black
Red
White
The direction of motor rotation is as viewed from the front shaft end of the motor
Gearhead and decimal gearhead are sold separately.
The code in of gearhead model is for gear ratio.
color indicates that the output shaft of the geared motor rotates in the same direction as the output shaft of the motor. Others indicate rotation in the opposite direction.
If you are to have less ratio than the ratio in the table, you can install the decimal gearhead, which has one tenth of the ratio, between the gearhead and the motor. In this case,
the permissible torque is 20N m/ 200kgfcm.
102 103
REVERSIBLE MOTORS
90W TERMINAL BOX TYPE
SPECIFICATIONS
CONNECTION DIAGRAMS
DIMENSIONS
GEARHEADS
DIMENSIONS
DECIMAL GEARHEAD GEARHEAD
RATED TORQUE OF GEARHEAD
30 minutes rating, four poles class E or A
RatedTorque
(mN m)(gfcm)
Speed
(rpm)
Condenser
( )
StartingTorque
(mN m)(gfcm)
Current
(A)
Frequency
(Hz)
Voltage
(V)
90
90
230
220
115
110
60
50
60 2.20
1.10
1.12
6006000
7107100
6006000
6000
600
6000
600
7107100
6006000
1550
1250 7
301500
60 1.106006000 1550
Output
(W)
single-phase
single-phase
Model
K9RP90FC-T
K9RP90FU-T
K9RS90FU-T
K9RS90FC-T
APPLICATION MODELPART No. L MOUNTING BOLT
DIMENSION TABLE
Speed(rpm)
Ratio
500
3
1.46
14.6
1.75
17.5
2.43
24.3
2.92
29.2
3.65
36.5
4.37
43.7
5.47
54.7
6.56
65.6
7.87
78.7
9.84
98.4
11.81
118.1
14.17
141.7
19.68
196.8
20
200
20
200
20
200
20
200
20
200
20
200
20
200
416
3.6
300
5
250
6
200
7.5
166
9
120
12.5
100
15
83
18
60
25
50
30
41
36
30
50
20
200
25
60
20
200
20
75
20
200
16
90
20
200
15
100
20
200
125
120
20
200
10
150
20
200
8.3
180
20
200
Model
Motor/
Gearhead
50Hzunit=above : N m / below : kgfcm
Speed(rpm)
Ratio
600
3
500
3.6
360
5
300
6
240
7.5
200
9
144
12.5
120
15
100
18
72
25
60
30
50
36
36
50
30
60
24
75
20
90
18
100
15
120
12
150
10
180
Model
Motor/
Gearhead
60Hzunit=above : N m / below : kgfcm
1.73
17.3
2.07
20.7
2.88
28.8
3.45
34.5
4.31
43.1
5.18
51.8
6.47
64.7
7.76
77.6
9.32
93.2
11.65
116.5
13.97
139.7
16.77
167.7
Black
White
Red
Black
Red
White
The direction of motor rotation is as viewed from the front shaft end of the motor
Gearhead and decimal gearhead are sold separately. The code in of gearhead model is for gear ratio.
color indicates that the output shaft of the geared motor rotates in the same direction as the output shaft of the motor. Others indicate rotation in the opposite direction.
If you are to have less ratio than the ratio in the table, you can install the decimal gearhead, which has one tenth of the ratio, between the gearhead and the motor. In this case,
the permissible torque is 20N m/ 200kgfcm.
104 105
GEARHEADS
DIMENSIONS
DECIMAL GEARHEAD GEARHEAD
RATED TORQUE OF GEARHEAD
GEARHEADS
DIMENSIONS
DECIMAL GEARHEAD GEARHEAD
RATED TORQUE OF GEARHEAD
APPLICATION MODELPART No. L MOUNTING BOLT
DIMENSION TABLEAPPLICATION MODELPART No. L MOUNTING BOLT
DIMENSION TABLE
Speed(rpm)
Ratio
500
3
1.46
14.6
1.75
17.5
2.43
24.3
2.92
29.2
3.65
36.5
4.37
43.7
5.47
54.7
6.56
65.6
7.87
78.7
9.84
98.4
11.81
118.1
14.17
141.7
19.68
196.8
20
200
20
200
20
200
20
200
20
200
20
200
20
200
416
3.6
300
5
250
6
200
7.5
166
9
120
12.5
100
15
83
18
60
25
50
30
41
36
30
50
20
200
25
60
20
200
20
75
20
200
16
90
20
200
15
100
20
200
12.5
120
20
200
10
150
20
200
8.3
180
20
200
Model
Motor/
Gearhead
50Hzunit=above : N m / below : kgfcm
Speed(rpm)
Ratio
600
3
500
3.6
360
5
300
6
240
7.5
200
9
144
12.5
120
15
100
18
72
25
60
30
50
36
36
50
30
60
24
75
20
90
18
100
15
120
12
150
10
180
Model
Motor/
Gearhead
60Hzunit=above : N m / below : kgfcm
1.73
17.3
2.07
20.7
2.88
28.8
3.45
34.5
4.31
43.1
5.18
51.8
6.47
64.7
7.76
77.6
9.32
93.2
11.65
116.5
13.97
139.7
16.77
167.7
Speed(rpm)
Ratio
500
3
416
3.6
300
5
250
6
200
7.5
166
9
120
12.5
100
15
83
18
60
25
50
30
41
36
30
50
25
60
20
75
16
90
15
100
13
120
10
150
8.3
180
Model
Motor/
Gearhead
50Hzunit=above : N m / below : kgfcm
Speed(rpm)
Ratio
600
3
500
3.6
360
5
300
6
240
7.5
200
9
144
12.5
120
15
100
18
72
25
60
30
50
36
36
50
30
60
24
75
20
90
18
100
15
120
12
150
10
180
Model
Motor/
Gearhead
60Hzunit=above : N m / below : kgfcm
23.29
232.9
27.95
279.5
30
300
30
300
30
300
30
300
30
300
30
300
1.73
17.3
2.07
20.7
2.88
28.8
3.45
34.5
4.31
43.1
5.18
51.8
6.47
64.7
7.76
77.6
9.32
93.2
11.65
116.5
13.97
139.7
16.77
167.7
1.46
14.6
1.75
17.5
2.43
24.3
2.92
29.2
3.65
36.5
4.37
43.7
5.47
54.7
6.56
65.6
7.87
78.7
9.84
98.4
11.81
118.1
14.17
141.7
19.68
196.8
23.62
236.2
26.57
265.7
30
300
30
300
30
300
30
300
30
300
Gearhead and decimal gearhead are sold separately. The code in of gearhead model is for gear ratio.
color indicates that the output shaft of the geared motor rotates in the same direction as the output shaft of the motor. Others indicate rotation in the opposite direction.
If you are to have less ratio than the ratio in the table, you can install the decimal gearhead, which has one tenth of the ratio, between the gearhead and the motor. In this case,
the permissible torque is 20N m/200kgfcm.
Gearhead and decimal gearhead are sold separately. The code in of gearhead model is for gear ratio.
color indicates that the output shaft of the geared motor rotates in the same direction as the output shaft of the motor. Others indicate rotation in the opposite direction.
If you are to have less ratio than the ratio in the table, you can install the decimal gearhead, which has one tenth of the ratio, between the gearhead and the motor. In this case,
the permissible torque is 3N m/30kgfcm.
