LEB LED HIGHBAY

IMPORTANT SAFETY INSTRUCTIONS

THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH T HE APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.

CE PRODUIT DOIT ÊTRE INSTALLÉ SELON LE CODE D’INSTA LLATION PERTINENT, PAR UNE PERSONNE QUI CONNAÎT BIEN LE PRODUIT ET SON FONCTIO NNEMENT AINSI QUE LES RISQUES INHÉRENTS.

1. READ AND FOLLOW ALL SAFETY INSTRUCTIONS.

2. INSTALLATION REQUIRES KNOWLEDGE OF LED LIGHTING AND ELECTRICAL SYSTEMS. RISK OF FIRE OR

ELECTRICAL SHOCK EXISTS.

3. DO NOT MAKE OR ALTER ANY OPEN HOLES IN AN ENCLOSURE OF WIRING OR ELECTRICAL COMPONENTS DURING KIT INSTALLATION.

4. DO NOT EXPOSE WIRING TO EDGE OF SHEET METAL OR OTHER SHARP OBJECTS IN ORDER TO PREVENT

WIRING DAMAGE OR ABRASION.

5. THE LED LUMINAIRE MUST BE WIRED IN ACCORDANCE WITH THE NATIONAL ELECTRICAL CODE AND APPLICABLE LOCAL CODES.

6. PROPER GROUNDING IS REQUIRED FOR SAFETY.

7. THIS LED LUMINAIRE MUST BE INSTALLED PER THE APPLICABLE INSTALLATION CODE BY A PERSON

FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT. DO NOT ATTEMPT INSTALLATION IF THIS CONDITION IS NOT MET. CONTACT A QUALIFIED ELECTRICIAN.

8. DO NOT USE THIS LUMINAIRE FOR ANYTHING OTHER THAN ITS INTENDED

USE.

9. DANGER-RISK OF FIRE OR ELECTRICAL SHOCK-DISCONNECT POWER BEFORE BEGINNING INSTALLATION.

LEB LED HIGHBAY

INSTALLATION

THIS FIXTURE IS INTENDED HUNG FROM CABLES OR PENDAN T MOUNT ONLY

1. Verify that the electrical power to the junction box is in the OFF position.

2. If the luminaire will be cable hung, find the provided Y cables provided. 3. Turn the paddles parallel with the cable and insert into the 3/8” diameter holes in the luminaire.

(see Figure 1)

4. Push both paddles through the 3/8” diameter holes and pull up on the end of the cable hanger.

(see Figure 2) Repeat on opposite side of luminaire. 5. Insert about 12” of the cable into one of the openings in the Adjustable Cable connector. (see

Figure 3). 6. Loop the end of the cable over a structure capable of holding the weight of the fixture(s) and feed

the end into the other hole in the Adjustable Cable connector. (see Figure 4)

7. Level the fixture by adjusting the Adjustable Cable connector. To release the tension on the cable, support the weight of the luminaire and press a paper clip or small Allen wrench into one of the small holes in the Adjustable Cable connector to adjust the cable length. Remove the paper clip or small Allen wrench to return the tension on the cable. (see Figure 5)

Figure 1 Figure 2

Figure 3 Figure 4

LEB LED HIGHBAY

8. Review the wiring details in this instruction guide. Connect the wire leads from the pendant pipe to the wire leads in the luminare and tuck all wires in the pendant box. Re-attach the pendant box to the luminare with the four screws that were removed in step 8.

9. For pendant mount, remove the four screws attaching the pendant box to the top of the luminaire. (See Figure 6)

10. Tighten a conduit lock nut onto the pendant pipe, place the luminaire pendant box onto the pipe, install a second conduit lock nut and tighten securely. (See Figure 7 & 8)

11. Review the wiring details in this instruction guide. Connect the wire leads from the pendant pipe to the wire leads in the luminare and tuck all wires in the pendant box. Re-attach the pendant box to the luminare with the four screws that were removed in step 8.

Figure 7

Figure 6

Figure 8

Figure 6

LEB LED HIGHBAY

DIMENSIONAL DATA

LEB 2 LEB 4

WIRING

Universal driver: 120VAC - 277VAC, 50/60HZ.

1. Verify that the electrical power to the Luminaire is in the OFF position. 2. NOTE - When used in a pendant mount or chain hung application stranded wire shall be used

from the supplied disconnect to the point where it connects to the branch circuit. 3. Connect the fixture side Black lead to Line supply lead 4. Connect the fixture side White lead to Neutral supply lead. 5. Connect the fixture side Green lead to Green supply lead. 6. Energize the electrical power and verify proper operation.

IN0001 Rev. 1 08/12/2016