Important Electrostatic Discharge and System Grounding Information for Cisco SCE 8000, Release 3.8.x

Revised: September 17, 2012, OL-26782-01

Note This document supports all 3.8.x releases.

OverviewBefore you install the Cisco SCE8000 chassis or touch the modules, read this document.

For more information on installing the Cisco SCE8000 platform, see either the Cisco SCE8000 10GBE Installation and Configuration Guide or the Cisco SCE8000 GBE Installation and Configuration Guide.

For information regarding configuring the Cisco SCE8000 platform, see either the Cisco SCE8000 10GBE Software Configuration Guide or the Cisco SCE8000 GBE Software Configuration Guide.

Americas Headquarters:Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA

Preparing Your Location

Preparing Your LocationMake sure that your building is correctly grounded to earth ground.

1878

76

Earth ground

2Important Electrostatic Discharge and System Grounding Information for Cisco SCE 8000, Release 3.8.x

OL-26782-01

Preparing the Rack Room

Preparing the Rack Room• Make sure that the rack enclosures are properly connected to the building earth ground.

• Make sure that the chassis is kept in a sealed antistatic bag prior to installation.

1878

77

Earth ground

Chassis protected in anti-static bag

3Important Electrostatic Discharge and System Grounding Information for Cisco SCE 8000, Release 3.8.x

OL-26782-01

Preparing Yourself

Preparing YourselfMake sure that you are properly grounded before you remove the antistatic bag from the chassis.

1878

78

Earth ground

4Important Electrostatic Discharge and System Grounding Information for Cisco SCE 8000, Release 3.8.x

OL-26782-01

Precautions When Unpacking a Chassis

Precautions When Unpacking a ChassisMake sure you are properly grounded when removing the antistatic bag from the chassis.

1878

79Earth ground

5Important Electrostatic Discharge and System Grounding Information for Cisco SCE 8000, Release 3.8.x

OL-26782-01

Precautions When Installing a Chassis

Precautions When Installing a ChassisMake sure that you are properly grounded and that you properly handle the chassis during installation.

1878

80

Earth ground

6Important Electrostatic Discharge and System Grounding Information for Cisco SCE 8000, Release 3.8.x

OL-26782-01

Grounding the Chassis

Grounding the Chassis• Make sure you properly connect the chassis (system) ground to the building ground.

• The chassis illustration below shows the system ground connector pad location for the Cisco SCE8000 chassis.

• The ground lug kit part number is 69-0815-01.

2744

87

FAN STATUS

SCM 1

SCM 2

SIP 3

4SCE8000-FAN

SYSTEM POWER

OPTICAL BYPASS

STATUS

AUXPORT 2

LINKACTIVE MASTER

SCE8000 EXTENDED SERVICE CONTROL MODULE

OPTICALBYPASS

OPTICALBYPASS

CONSOLE

10 1001000

LINKACTIVE

PORT 1

A C

A BC D

B D

STATUS

CTRL

OPB-SCE8K-MM

OPTICAL BYPASS1

TX

RX

TX

RX

TX

RX

TX

RX

A C

A BC D

B D

STATUS

CTRL

OPB-SCE8K-MM

OPTICAL BYPASS2

TX

RX

TX

RX

TX

RX

TX

RX

SYSTEM POWER

OPTICAL BYPASS

STATUS

AUXPORT 2

10 1001000

LINKACTIVE MASTER

SCE8000 EXTENDED SERVICE CONTROL MODULE

SCE8000-SCM-E

SCE8000-SCM-E

SCE8000-SIP

CONSOLE

10 1001000

LINKACTIVE

PORT 1

OPTICALBYPASS

OPTICALBYPASS

STATUS

ACTIVE/LINK

SPA-1X10GE-L-V2

STATUS

ACTIVE/LINK

SPA-1X10GE-L-V2STATUS

ACTIVE/LINK

SPA-1X10GE-L-V2

STATUS

ACTIVE/LINK

SPA-1X10GE-L-V2

10 1001000

Earthground

7Important Electrostatic Discharge and System Grounding Information for Cisco SCE 8000, Release 3.8.x

OL-26782-01

Transporting Line Cards

Transporting Line CardsKeep the line card in a sealed antistatic bag when transporting.

1878

82

Earth ground

8Important Electrostatic Discharge and System Grounding Information for Cisco SCE 8000, Release 3.8.x

OL-26782-01

Handling Line Cards

Handling Line Cards• Properly ground yourself before you remove the line card from the antistatic bag.

• Handle the line card by the front panel and the metal carrier only.

1878

83

Earth ground

9Important Electrostatic Discharge and System Grounding Information for Cisco SCE 8000, Release 3.8.x

OL-26782-01

Removing and Installing Line Cards

Removing and Installing Line Cards• Make sure you are properly grounded before removing or installing line cards.

• Make sure you properly handle the line card by the front panel and the metal carrier only.

1878

84

Earth ground

10Important Electrostatic Discharge and System Grounding Information for Cisco SCE 8000, Release 3.8.x

OL-26782-01

Grounding the Work Surface

Grounding the Work Surface• Make sure that you and the work surface that you are placing the line card on are properly grounded.

• Your wrist strap, the rack enclosure, and the work surface should all be attached to the building ground.

2745

32

Earth ground

11Important Electrostatic Discharge and System Grounding Information for Cisco SCE 8000, Release 3.8.x

OL-26782-01

Grounding the Work Surface

Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1110R)

Any Internet Protocol (IP) addresses used in this document are not intended to be actual addresses. Any examples, command display output, and figures included in the document are shown for illustrative purposes only. Any use o f actual IP addresses in illustrative content is unintentional and coincidental.

© 2012 Cisco Systems, Inc. All rights reserved.

12Important Electrostatic Discharge and System Grounding Information for Cisco SCE 8000, Release 3.8.x

OL-26782-01