Page 1 of 6

Illustrated Parts & Packing List

815 rice Lake Street, Owatonna, MN 55060

For a complete distributor & dealer list go to www.gandy.net

2848DP

Dethatcher (Chain Driven)

(This Parts & Packing list is for units built & shipped BEFORE January 1, 2012)

(All Parts & Hardware in Place Unless Otherwise Specified)

1 ....................... 2893-1 .................................. Main Dethatcher Base

Use: 5 Grease Fitting (D01-5010-050)

2 ....................... 638735-6 .............................. Hitch Pin, Cat 1

Use: 2 Linch Pin (7/16 x 1-3/4)(M11-0437-175)

2 Lock Washer (7/8)(C02-0875-010)

2 Jam Nut (7/8-14)(C01-0875-060)

1 ....................... 0706980-5 ............................ Yoke Pin, Cat 1

Use: 1 Spring Pin (5/16 x 2)(C23-0312-220)

1 Linch Pin (7/16 x 1-3/4)(M11-0437-175)

1 ....................... 2893-2 .................................. Hitch Brace Weldment

Use: 1 Slotted Hex Nut (5/8)(C01-0625-070)

1 Cotter Pin (5/32 x 1)(C20-0156-020)

2 ....................... 2893-4 .................................. Pivot Bracket, 3-Point Hitch

2 ....................... 2893-5 .................................. Bushing (7/8 O.D. x 7/16-Long)

Use: 1 Hex Bolt (5/8 x 4)(C03-0625-161)

2 SAE Washer (5/8)(C02-0625-020)

1 Lock Washer (5/8)(C02-0625-010)

1 Hex Nut (5/8)(C01-0625-010)

1 ....................... 2893-6 .................................. Spacer (7/8 O.D. x 2-inch Long)

Use: 1 Hex Bolt (5/8 x 3-1/2)(C03-0625-141)

1 Lock Washer (5/8)(C02-0625-010)

1 Hex Nut (5/8)(C01-0625-010)

1 ....................... G07-0020-000 ..................... PTO Drive Shaft (Fastened to 3-Point Hitch Arms For Shipping)

1 ....................... G05-1020-000 ..................... Gear Box, Right Angle

Use: 2 Mount Spacer, Gear Box ( 2893-8)

4 Bushing (3/4 O.D. x .703 Long)(2893-36)

2 Hex Bolt (3/8 x 6)(C03-0375-201)

2 Hex Bolt (3/8 x 6-1/2)(C03-0375-211)

4 Wrought Washer (3/8)(C02-0375-030)

4 Whiz Flange Nut (3/8)(C01-0375-030)

1 ....................... 2893-35 ................................ Guard, PTO Shaft

Use: 2 Whiz Flange Nut (3/8)(C01-0375-030)

2 ....................... D05-1000-060 ..................... Bearing w/Locking Collar

Use: 4 Carriage Bolt (5/16 x 3/4)(C04-0312-031)

4 Lock Washer (5/16)(C02-0312-010)

4 Hex Nut (5/16)(C01-0312-010)

Page 2 of 6

1 ....................... 2893-69 ................................ Shaft, Gear Box to Knives

Use: 1 Hex Bolt (5/16 x 1)(C03-0312-041)

1 Lock Washer (5/16)(C02-0312-010)

1 Clutch Washer (62854-29)

1 ....................... 2893-68 ................................ Collar Spacer

2 ....................... K18-4016-100 ..................... Coupler Sprocket, Chain, for 1-Inch Shaft

Use: 2 Key (1/4 x 1-1/4)(2893-40)

1 ....................... K18-4016-101 ..................... Chain Assembly for Coupler

2 ....................... G01-0015-030 ..................... Sprocket, 15-Tooth, 1-Inch Bore, w/ 1/4-Keyway

Use: 1 Key (1/4 x 2-5/8)(2893-38)

1 ....................... 2893-61 ................................ Spacer w/Keyway (1-1/2 O.D. x 3/4 Long)

2 ....................... F02-0050-047 ...................... Roller Chain O-Ring #50 (47-Links)

2 ....................... F02-0050-001 ...................... O-Ring Connector Link #50

1 ....................... 2893-37 ................................ Shaft, Tightener (5/8 Round x 4-1/2 Long)

Use: 1 Socket Set Screw (#10-24 x 5/16)(C06-0187-030)

1 ....................... 2893-58 ................................ Chain Tightener

Use: 1 Retainer Clip (E-Clip) For 5/8 Shaft (C24-1000-062)

1 ....................... 2893-60 ................................ Chain Tightener, Idler Pulley

1 ....................... 2893-63 ................................ Tightener Rod, Chain Drive

Use: 1 Cotter Pin (5/32 x 1)(C20-0156-020)

1 Die Spring (Copper Colored)(3/4 x 1-1/2)(E00-0750-150)

1 Whiz Flange Nut (3/8)(C01-0375-030)

1 Wrought Washer (3/8)(C02-0375-030)

1 Lock Nut, Nylon (3/8)(C01-0375-041)

1 ....................... 2893-12 ................................ Shaft, Wheel Lift (40-3/8 x 1)

1 ....................... 2893-13 ................................ Wheel Lift Arm

Use: 1 SAE Washer (1-Inch)(C01-1000-020)

1 Key (1/4 x 1-3/4)(2893-41)

2 Socket Set Screw (5/16-18 x 1/4)(C06-0312-010)

2 Socket Set Screw (5/16-18 x 3/8)(C06-0312-030)

1 ....................... 2893-14 ................................ Shaft, Wheel Lift, Left (16 x 1)

Use: 1 Socket Set Screw (#10-24 x 5/16)(C06-0187-030)

2 ....................... 2893-15 ................................ Counter Arm Weldment, Wheel Lift

Use: 2 Key (1/4 x 1-1/4)(2893-40)

2 Socket Set Screw (5/16-18 x 1/4)(C06-0312-010)

2 Socket Set Screw (5/16-18 x 3/8)(C06-0312-030)

1 ....................... F10-0625-010 ...................... Turnbuckle (5-inch x 6-inch Take-Up)

Use: 1 Hex Nut (5/8)(C01-0625-010)

1 Hex Bolt (1/2 x 2-1/4)(C03-0500-091)

1 Hex Bolt (1/2 x 4-1/2)(C03-0500-071)

2 Lock Washer (1/2)(C02-0500-010)

2 Lock Nut, Center Point (1/2)(C01-0500-040)

1 Bushing (3/4 O.D. x 11/16 Long)(6108534-19)

1 ....................... 2893-17 ................................ Rear Wheel Arm, Left

Use: 1 Retainer Clip (E-Clip)(For 1-inch Shaft)(C24-1000-098)

1 ....................... 2893-18 ................................ Rear Wheel Arm, Right

Use: 1 Retainer Clip (E-Clip)(For 1-inch Shaft)(C24-1000-098)

2 ....................... 2893-16 ................................ Wheel Adjustment Arm

Use: 2 Hex Nut (1/2)(C01-0500-010)

4 Yoke End (F10-0300-050)

2 Rod (1/2-13 Threaded x 6-Inch)(2893-16/3)

4 Hex Bolt (7/16 x 1-3/4)(C03-0437-071)

4 Lock Nut, Center Point (7/16)(C01-0437-040)

Page 3 of 6

4 ....................... R02-0011-000 ...................... Tire & Rim Assembly (Not In Place, Shipped In Hopper)

4 ....................... M04-0002-003 ..................... Wheel Hub, 4-Bolt Flange, w/ 3/4-I.D. Bearing

Use: 2 Whiz Flange Bolt (5/16 x 5/8)(C03-0312-021)

2 Wrought Washer (5/16)(C02-0312-030)

2 Wrought Washer (3/8)(C02-0375-030)

8 Hub Nut (5/16-24)(C01-0312-080)

1 ....................... 2893-32 ................................ Guard, Gear Box to Knife Drive Shaft

Use: 4 Whiz Flange Bolt (5/16 x 5/8)(C03-0312-021)

1 ....................... 2893-33 ................................ Chain Guard Weldment

Use: 4 Hex Bolt (1/4 x 1/2)(C03-0250-010)

4 Lock Washer (1/4)(C02-0250-010)

1 ....................... 2893-34 ................................ Chain Shield, Bottom

Use: 4 Hex Bolt (1/4 x 1/2)(C03-0250-010)

4 Lock Washer (1/4)(C02-0250-010)

1 ....................... 2893-A ................................. Front Wheel Hub Assembly Consisting of The Following:

2 ................ D05-1000-050 ..................... Bearing, For 1-inch Shaft, w/ Set Screws

Use: 4 Carriage Bolt (5/16 x 3/4)(C04-0312-031)

4 Lock Washer (5/16)(C02-0312-010)

4 Hex Nut (5/16)(C01-0312-010)

1 ................ 2893-19 ................................ Shaft, Front Wheel (64-1/4 x 1)

1 ................ 2893-21 ................................ Drive Wheel Hub Sprocket Weldment, Left

Use: 1 Clevis Pin (1/4 x 1-3/4)(C22-0250-120)

1 Cotter Pin (3/32 x 3/4)(C20-0093-020)

4 Hub Nut (5/16-24)(C01-0312-080)

1 ................ 2893-20 ................................ Wheel Hub Extension Weldment, Right

Use: 1 Clevis Pin (1/4 x 1-3/4)(C22-0250-120)

1 Cotter Pin (3/32 x 3/4)(C20-0093-020)

4 Hub Nut (5/16-24)(C01-0312-080)

1 ....................... 2893-C ................................. Saw-Tooth 8-inch Knife Blade Assembly:

Consisting of The Following:

1 ................ C01-1000-070 ...................... Hex Slotted Nut (1”-14)

Use: 1 Cotter Pin (3/16 x 1-3/4)(C20-0187-050)

2 ................ G01-0012-030 ..................... Sprocket 12-Tooth, 1-Inch Bore w/ 1/4-Keyway

1 ................ 2893-24 ................................ Shaft (54-5/8 x 1-Inch Hex)

22 .............. 2893-27 ................................ Spacer, (Between Knife Blades) (1-3/8 O.D. x 1.926)

1 ................ 2893-30 ................................ Spacer, Left End (1-3/8 x 1.656)

1 ................ 2893-31 ................................ Castellated Nut, Cut-Off (1”-14)

Use: 1 Cotter Pin (3/16 x 1-3/4)(C20-0187-050)

1 ................ 2893-38 ................................ Key (1/4 x 2-5/8)

3 ................ 2893-44 ................................ Flange Bearing

Use: 6 Carriage Bolt (5/16 x 3/4)(C04-0312-031)

6 Lock Washer (5/16)(C02-0312-010)

6 Hex Nut (5/16)(C01-0312-010)

1 ................ 2893-45 ................................ Spacer, Right Center (1-3/8 x .710)

1 ................ 2893-46 ................................ Spacer, Left Center (1-3/8 x .275)

1 ................ 2893-61 ................................ Spacer, w/ 1/4-Keyway (1-1/2 x 3/4)

1 ................ 2893-62 ................................ Spacer (1-1/2 x 3/4)

12 .............. 2893-49 ................................ Blade, 8-Inch Saw-Tooth 30 Deg, 14 Gauge

(w/Square Hole or round Hole)

12 .............. 2893-50 ................................ Blade, 8-Inch Saw-Tooth 90 Deg, 14 Gauge

(w/ two triangle Holes or No Holes)

Page 4 of 6

Page 5 of 6

Page 6 of 6

September 11, 2014

Revised From (8/9/13)

Printed in the USA