Upload
others
View
1
Download
0
Embed Size (px)
Citation preview
Congratulations on your purchase of an Ikelite Digital CameraHousing. Ikelite has over 45 years of experience in the underwaterphotographic and lighting market. Our products are designed andbuilt in the USA by Ikelite for both the professional and amateurphotographer.
The clear housing permits instant visual inspection of the cameraand all sealing surfaces as well as complete monitoring of controlsand camera LCD screens.
Ikelite Digital Housings are slightly negative in salt water forstability. This housing has been water pressure tested at thefactory. Housing is pressure tested to 200' (60m).
Ikelite Digital Housingi n s t r u c t i o n m a n u a l
#6182.16 for Nikon Coolpix P60
PPlleeaassee RReeaaddWe suggest that you read this instruction booklet thoroughlybefore use. If you are new to underwater photography be sureto read the General and Photo Tips.
We also suggest that you read the camera manual thoroughlyto have a full understanding of where each camera control islocated and what function each control provides.
PPlleeaassee RReeaadd IIff UUssiinngg aann EEVV--CCoonnttrroolllleerrThe EV-Controller used with Ikelite DS Substrobes have twouser settings. One setting is for strobe selection, the other is forpre-flash or non pre-flash. TThhiiss ccaammeerraa uusseess pprree--ffllaasshh, thus theEV-Controller should be set to the pre-flash position when usedwith this camera.
2
CCaammeerraa SSeettuupp1. Use of “M” Manual exposure mode is recommended.
2. Set ISO to “80”.
3. Set shutter speed to 1/200th second.
4. Set Aperture to f8.5-10.9 for macro photograhy (close-ups).
3
Front View
Shutter Release
Lid Snap
Playback
DeleteMenu
Multi-Selector
OK
Lid Snap
LensPort
Back View
Lanyard
ThumbRest
On/Off Mode Dial
ZoomMonitor
4
OOppeenniinngg tthhee HHoouussiinngg1. Lid Snaps have a LLoocckk.
To open, push Lid Snap Lockforward and lift as shown.Keep pressure on the Lid Snapso it does not flyopen quickly.Some lid snaps have a lotof spring tension once they go over center, have a firm gripon the lid snap. Lid Snaps may be opened one at a time.
IInnssttaalllliinngg tthhee CCaammeerraa1. Remove the back from the housing. The mounting tray for the
camera is secured tothe housing back.Position the cameraon the tray andsecure it with themounting bolt whichthreads into thecamera's tripodsocket. UUsseeaa ccooiinn oorr ffllaatt bbllaaddeeddssccrreewwddrriivveerr ttoottiigghhtteenn tthhee mmoouunnttiinnggbboolltt ssoo tthhee ccaammeerraa iissffllaatt aaggaaiinnsstt tthhee ttrraayy..
CCAAUUTTIIOONN::Some camera tripod socket threads are plastic. The mountingtray bolt is metal. Do not cross thread or over tighten as youmay damage the camera tripod socket threads.
CAMERA / MOUNT
O' Ring
LidHook
Mounting BoltMounting Tray
NIKON
Lift
Push Forward
Lid Snap Lock
8
UUssiinngg FFllaasshhUUssiinngg tthhee CCaammeerraa’’ss BBuuiilltt--iinn FFllaasshh..
If you do not have an external flash, the camera’s built-in flashcan be used. See Diffuser instructions.
NOTE: The camera’s built-in flash cannot be used with optionalWide-angle lenses.
DDiiffffuusseerr aanndd DDeefflleeccttoorr IInnssttaallllaattiioonn
Housing shown withDeflector installed.
Deflector
CClloossiinngg tthhee HHoouussiinngg1. Place housing face down in your
lap or on flat surface.2. Check to see that there is an
o-ring on the housing back andthat it is clean and in its properlocation.
3. Guide the back onto the housing.The o-ring should touch thehousing all the way around. Thereshould be an even gap all the wayaround between the housing andthe housing back.
4. Lift the lid snaps so they areextended and place the lidsnap into the hook on thehousing back.
5. To close the housing push down on the lid snaps until they snap into place . Lid snaps on opposite sides of thehousing should be closed at thesame time. Be sure they are downfar enough to engage the lock.
DDoouubbllee cchheecckk - Once the housing is closed, check the o-ring seal.Check the gap between the housing back and the housing, itshould be even all the way around.Look through the clear plastic back at the o-ring. You should seea darkened area where the o-ring is compressed against thehousing back. If you do not see an even black compression sealall the way around the back, open the lid snaps, reseat thehousing back and close the lid snaps. Visually check the seal again.
o-ring
housing back
housing back
o-ring
even gapall 4 sides
5
CChheecckkiinngg CCoonnttrroollssOnce the housing has been closed, make sure the housing controlsline up with the camera’s controls. If the housing controls aremisaligned slightly make sure the camera hold down bolt has beentightened down firmly so the camera is flat against the tray.
TTuurrnn CCaammeerraa OOnnTurn the camera on and operate each of the housing controls toget a feel for using the camera in the housing. Take a few picturesabove water with the camera in the housing.
6
LLuubbrriiccaannttss1. Ikelite provides silicone lubricant with the housing. We recommend
you use only Ikelite lubricant on Ikelite products as some otherbrands may cause the o-ring to swell and not seal properly.
2. Use only enough lubricant to lightly cover control shafts ando-rings. Wipe off any excess lubricant with a clean cloth.Lubricant is not a sealant, it is used to reduce friction. Excessivelubricant can collect sand and dirt which may interfere withproper sealing.
CCAAUUTTIIOONNNNeevveerr uussee sspprraayy lluubbrriiccaannttss aass tthhee pprrooppeellllaanntt iinnggrreeddiieenntt ccaannccaauussee tthhee ppllaassttiicc hhoouussiinngg ttoo ccrraacckk..
7
DDiiffffuusseerr aanndd DDeefflleeccttoorr ccoonntt..A diffuser and deflector areincluded with the housing.The diffuser is whitetransparent plastic. Thedeflector is also white but isnot transparent.
To install the diffuser ordeflector spread the portclamp at the spring end andslide over the lens port. Thewhite plastic should beplaced in front of the cameraflash. The port clamp shouldbe pushed back against the front of the housing.
DDiiffffuusseerrThe diffuser should be installed when using the camera’s builtin flash. When shooting with the camera’s built-in flash atapproximately 2 feet (0.6 m) or less, the lens port on thehousing may block a portion of the light from the camera’sbuilt-in flash, creating a shadow in the lower left of the photo.If this occurs, zoom the lens slightly to eliminate the shadow.(You can test this above water)
DDeefflleeccttoorrThe deflector should be installed when using an external strobesuch as the DS51 or DS125 Substrobe and EV Controller. Thedeflector will redirect the camera’s flash to the EV Controllerwhich controls the external strobes output.
Diffuser/Deflector material
Port Clamp
Spring
Spread to Install
OOppttiioonnaall AAcccceessssoorriieessBBaacckk oo--rriinngg ##00110099
O-rings last for several years if properly maintained. (Seemaintenance) Always carry a spare in case o-ring becomesdamaged or lost.
UURR//PPrroo FFiilltteerr ((BBlluuee WWaatteerr)) ##66444411..3322The UR/Pro underwater color correcting filter is designed torestore some of the warm colors filtered out by the water. Foravailable light use only, not recommended for use with flash.
GGrreeeenn WWaatteerr FFiilltteerr ##66444411..7722Enhances contrast and alters the color of green water to giveour subject a rich, natural tone. For available light only, notrecommended for use with flash.
TTrraayy wwiitthh RReelleeaassee HHaannddllee ##99552233..3311Tray and Release Handle is required to mountexternal Substrobes.
IIkkeelliittee WW--2200 WWiiddee--AAnnggllee LLeennss ##6644220067mm Wide-Angle lenses allow you to capture more of thescene and get closer to your subjectwhich results in clearer images and morevivid color. These lenses can be installedor removed underwater for maximumversatility. NNoottee:: #9603.81 Wide-Angleadaptor is required.
10
11 12
SSuubbssttrroobbee DDSS112255 The Substrobe DS125 coversthe equivalent of a 18mmlens, 100 degrees. It is theideal choice when usingaccessory wide angle lensesgreater than 28mm.
Substrobe DS51
SSuubbssttrroobbee DDSS5511The Substrobe DS51 covers theequivalent of a 28mm lens. It isthe ideal choice when usingonly the camera lens or thecamera lens with a macroaccessory lens.
Substrobe DS125
SA-100QArm SA-100Q
Arm
EV Controller
OOppttiioonnaall AAcccceessssoorriieess CCoonnttiinnuueedd
AF35 Autoflash kit includes:
- AF35 strobe
- Flex arm
- AutoFlash sensor
- Handle with rubber grip
- Tray (single or dual)
- Mounting hardware
The Autoflash AF35 replicates your camera's flash for automatic exposure inany situation. Single or dual trays canattach directly to your housing. Theexposure selector dial on the side of thesensor provides fine tuning to optimizeresults with a variety of digital still cameras. Once you find an exposure levelthat you like, leave the dial on that number for automatic operation.
CCoommpplleettee iinnffoorrmmaattiioonn rreeggaarrddiinngg ooppttiioonnaall aacccceessssoorriieess aavvaaiillaabbllee aattwwwwww..iikkeelliittee..ccoomm
EV Controller
OOppttiioonnaall AAcccceessssoorriieess CCoonnttiinnuueedd::NNoottee:: EV “Manual” Controller required with DS-series substrobes
9
LLeennss PPoorrttTreat the glass in the lens port as a camera lens. After use, rinseand gently dry the lens port to avoid water spotting. To cleanuse a mild soap solution or lens cleaner.
Do not use alcohol or window cleaner on the Lens Port.
Wide-Angle Adapter #9306.81 is required to mount the #6420Ikelite W-20 Wide-Angle Lens and other manufacturers (67mm)screw thread style wide-angle lenses.The 67mm style lenses can be secured onto the Wide-AngleAdapter above or below water as they are designed to havewater between the front of the port and the accessory lens.Make sure no air bubbles are trapped between the port and theaccessory lens. Any vignetting that occurs can be eliminated bycropping the image in post-processing, or by zooming thecamera lens slightly. Zooming the lens with a Wide AngleAdaptor attached can cause the image edges to soften. Thecamera's built-in flash cannot be used with wide angle lenses.The front of the lenses are solarge they block the camera'sflash. To properly lightsubjects when using a wideangle lens, an external strobeshould be used. Due to thewide-angle coverage of theselenses, the DS125 Substrobe ortwo DS51 Substrobes isrecommended.
Bayonet mount adaptor lensescannot be used due to extremevignetting.
Wide-Angle Lens
Wide-Angle Adapter
CCoonnttrrooll MMaaiinntteennaannccee Ikelite controls are designed to provide years of reliable servicewith minimal maintenance.1. Push button controls require no maintenance other than rinsing
in fresh water after saltwater use. If a push button controlbecomes difficult to push or if it sticks when depressed, soak thehousing in luke warm fresh water. After a few minutes operatethe push button. If this does not correct the problem, return thehousing to Ikelite for maintenance.
2. Some of the controls have long shafts. These controls can bepulled out, exposing the shaft (see drawing). To lubricate the control, gently pull on the knob until thestainless steel shaft is exposed. Lightly lubricate the shaft, thenmove the shaft in and out several times. This will lubricate thex-ring in the Ikelite control gland. This should be done beforeusing the housing after a prolonged storage period, or once aweek when the housing is in use.
housing
lubricate shaft
pull out toexpose shaft
13
MMaaiinntteennaanncceeThe Ikelite Digital Housing should be given the same care andattention as your other photographic equipment. In addition tonormal maintenance we recommend that the housing be returnedto Ikelite periodically to be checked and pressure tested.1. DDoo NNoott leave the camera and housing in direct sunlight for
prolonged periods. Heat may damage the camera.2. DDoo NNoott ship the camera in the housing.3. Before using the housing, always check the tightness of the sseett
ssccrreeww in each control knob. Check each ccoonnttrrooll ggllaanndd penetrating the housing to make surethey are tight. There is a slight chance that either could vibrateloose during travel.
4. Keep the back o-ring clean and lightly lubricated. To lubricateremove the o-ring from the back. Put a small amount of lkelitelubricant on your fingers. Draw the o-ring through your fingersto apply a light coating of lubricant. Only apply enoughlubricant to make the o-ring feel slick. DDoo NNoott ssttrreettcchh tthheeoo--rriinngg. This light coating of lubricant will help to keep theo-ring from drying out and will help to show a dark sealingline when the housing back is properly sealed.
5. Keep the area where the o-ring fits and the sealing surface ofthe housing clean.
6. Rinse the housing exterior thoroughly in fresh water after eachsalt water use. Dry with a soft cloth. Dry lens port to eliminatewater spotting.After several uses in salt water soak the housing exterior in amild soap solution, rinse and dry before storage. When storingthe housing, remove the back o-ring, lightly lubricate and placein a plastic bag. Place the plastic bag with o-ring inside thehousing for safe keeping.
7. If removing a housing push button, DDoo NNoott re-use the E-clip.Contact Ikelite for replacement E-clips (part #0319.12).
14
16
GGeenneerraall TTiippss1. Due to the power required to operate the camera, flash, and
LCD screen it is a good idea to start each dive with a fresh setof batteries.
2. Some cameras reset their flash to AUTO when the camera isturned on. If you prefer another setting be sure to select it.
3. As soon as you enter the water, take a moment and check thehousing to see that it is properly sealed.
4. Next, check to see if there are any bubbles on the face of thelens port. If there are, take your finger and remove them. Ifthere are bubbles on the lens port they can produce soft focusspots in your photographs.
NNOOTTEE5. If you are shooting with the camera’s built-in flash and the
cameras lens is set to the widest angle you may need to zoomthe lens slightly or a shadow may appear in the lower leftcorner of close-up photographs. The lens port may block someof the light. Installing the flash diffuser will help to eliminatethe shadow. (You can test this above water)
To shoot photographs closer than 2 feet (0.6m), you need touse an external strobe such as the DS51 or DS125. With anexternal strobe you can position it so nothing blocks the lightpath between the strobe and the subject.
CCoonnttrrooll MMaaiinntteennaannccee CCoonntt..3. Some of the controls have a short shaft and cannot be pulled
out exposing the shaft for lubrication. In the unlikely event oneof these controls sticks or becomes difficult to operate you canremove the control from the housing and lubricate it, or returnthe housing to Ikelite for maintenance. To remove the control,loosen the set screw in the knob (allen wrench required);remove the knob. If there is salt or dirt build-up on the exposedcontrol shaft, clean the shaft. Open the housing and gently slidethe control shaft out of the control gland. Clean and lightlylubricate the shaft, including the end of the shaft. Slide theshaft back into the control gland and gently slide it back andforth a few times without fully removing the shaft from thegland. Replace the knob, NOTE the flat area on the shaft, theset screw in the knob should tighten down against the flat areaon the control so the knob does not turn on the shaft.
Loosen set screw(allen wrench required)
Control shaft flat: Tighten set screw downagainst this area when
replacing the knob.
housingglandcontrol
shaft
Lubricate end of shaftbefore reinserting intogland
15
18
PPhhoottoo TTiippss1. The number one rule in underwater photography is eliminate
as much water between camera and subject as possible. Getas close as you can to the subject, then use the zoom. If youare using flash, subjects beyond 6 feet (1.8m)will not havemuch color.
2. The camera’s built-in flash is very close to the camera lens. Theflash can light up any suspended particles in the water and theycan be recorded in your picture. This effect is called backscatter.To eliminate as much backscatter as possible, photograph close.Photograph in clear water; do not stir up the sand or siltybottom. If backscatter becomes a problem in the environmentyou are photographing, an external flash will help eliminatemuch of the backscatter.
3. Digital cameras have a slight lag time between when you pressthe shutter release button and the camera actually takes thepicture. Hold the camera steady a second or two after pressingthe shutter release button.
4. Do not shoot down on subjects as they will quite often blendinto the background and be difficult to see in the photograph.Shoot subjects straight on or shoot up at a slight angle usingthe blue water as a contrasting background.
5. Underwater flash is used to restore the warmer colors filteredout by the water as well as to illuminate the subject. Whenphotographing underwater, set the camera to use flash onevery shot. If the camera’s flash is set to AUTO and the sun isbehind your subject, the camera may see enough light that itdoes not fire the flash. With the sun behind the subject thesubject is shaded (dark) and needs flash for a good exposure.
17
19
PPhhoottoo TTiippss CCoonntt..6. When using daylight or flash if your camera consistently over
or underexposes the image you may want to adjust yourcamera’s exposure compensation settings. Many cameras allowyou to adjust both available light and flash exposure with anEV control in the camera’s menu.
7. Many photographers transfer their images to the computerwhere they can fine tune the appearance of the image. Manyof the image manipulation programs make you think you canmagically correct any image taken and make a good picture.One thing to remember when using image manipulationprograms, if the image is overexposed much of the color ismissing. If the color is missing you cannot adjust it. If imagesare slightly underexposed the color is there, it is just dark andyou can adjust it to some degree. So if you error in exposure itis better to have the image slightly underexposed than overexposed.
IIkkeelliittee LLiimmiitteedd WWaarrrraannttyyAll Ikelite products are warranted against any manufacturingdefects for a period of one year from the date of purchase.Defective products should be returned prepaid to Ikelite. Ikelitewill, at its discretion, repair or replace such products, and willreturn to customer prepaid. All other claims, of any nature,including but not limited to bulb failure are not covered. Exceptas mentioned above, no other warranty expressed or implied,applies to this Ikelite product.
RReettuurrnniinngg PPrroodduuccttss ffoorr SSeerrvviicceeIkelite is most interested in preforming any service to assure thatall products perform as intended. For repair or service, return theproduct to the address below with your name, address, phonenumber and a brief description of the problem. Evidence ofpurchase date must be provided to obtain warranty service.Normal service turnaround time is approximately 2-3 weeks.
IIkkeelliittee UUnnddeerrwwaatteerr SSyysstteemmss5500 WW 3333rrdd SSttrreeeett
IInnddiiaannaappoolliiss,, IINN 4466220088 UUSSAA
WWhheenn rreettuurrnniinngg pprroodduuccttss sseenndd ““aattttnn.. RReeppaaiirr DDeepptt..””
331177--992233--44552233
““ggeenneerraall qquueessttiioonnss”” ee--mmaaiill:: iikkeelliittee@@iikkeelliittee..ccoommwwwwww..iikkeelliittee..ccoomm
NNOOTTEESS::
__________________________________________________________________________________________________
__________________________________________________________________________________________________
__________________________________________________________________________________________________
__________________________________________________________________________________________________
__________________________________________________________________________________________________
__________________________________________________________________________________________________
__________________________________________________________________________________________________
__________________________________________________________________________________________________
__________________________________________________________________________________________________
__________________________________________________________________________________________________
__________________________________________________________________________________________________
__________________________________________________________________________________________________
DDiiggiittaall 66118822..1166--0011--00550088