ICEM Mesh Generation

Embed Size (px)

Citation preview

  • 8/18/2019 ICEM Mesh Generation

    1/8

    See discussions, stats, and author profiles for this publication at: https://www.researchgate.net/publication/265376812

    Letter to Obinichi Nnorom some ICEM meshgeneration guidelines

    Technical Report · September 2014

    DOI: 10.13140/2.1.5140.4166

    READS

    244

    1 author:

    Ricardo Vicente de Paula Rezende

    Federal University of Santa Catarina

    96 PUBLICATIONS  66 CITATIONS 

    SEE PROFILE

    Available from: Ricardo Vicente de Paula Rezende

    Retrieved on: 16 April 2016

    https://www.researchgate.net/institution/Federal_University_of_Santa_Catarina2?enrichId=rgreq-c251c9aa-04af-41a9-a4b1-7abb4a3b77b7&enrichSource=Y292ZXJQYWdlOzI2NTM3NjgxMjtBUzoxMzgxMTc2MzgwMDQ3MzZAMTQwOTk0MTIxOTEwMA%3D%3D&el=1_x_6https://www.researchgate.net/profile/Ricardo_Rezende2?enrichId=rgreq-c251c9aa-04af-41a9-a4b1-7abb4a3b77b7&enrichSource=Y292ZXJQYWdlOzI2NTM3NjgxMjtBUzoxMzgxMTc2MzgwMDQ3MzZAMTQwOTk0MTIxOTEwMA%3D%3D&el=1_x_5https://www.researchgate.net/?enrichId=rgreq-c251c9aa-04af-41a9-a4b1-7abb4a3b77b7&enrichSource=Y292ZXJQYWdlOzI2NTM3NjgxMjtBUzoxMzgxMTc2MzgwMDQ3MzZAMTQwOTk0MTIxOTEwMA%3D%3D&el=1_x_1https://www.researchgate.net/profile/Ricardo_Rezende2?enrichId=rgreq-c251c9aa-04af-41a9-a4b1-7abb4a3b77b7&enrichSource=Y292ZXJQYWdlOzI2NTM3NjgxMjtBUzoxMzgxMTc2MzgwMDQ3MzZAMTQwOTk0MTIxOTEwMA%3D%3D&el=1_x_7https://www.researchgate.net/institution/Federal_University_of_Santa_Catarina2?enrichId=rgreq-c251c9aa-04af-41a9-a4b1-7abb4a3b77b7&enrichSource=Y292ZXJQYWdlOzI2NTM3NjgxMjtBUzoxMzgxMTc2MzgwMDQ3MzZAMTQwOTk0MTIxOTEwMA%3D%3D&el=1_x_6https://www.researchgate.net/profile/Ricardo_Rezende2?enrichId=rgreq-c251c9aa-04af-41a9-a4b1-7abb4a3b77b7&enrichSource=Y292ZXJQYWdlOzI2NTM3NjgxMjtBUzoxMzgxMTc2MzgwMDQ3MzZAMTQwOTk0MTIxOTEwMA%3D%3D&el=1_x_5https://www.researchgate.net/profile/Ricardo_Rezende2?enrichId=rgreq-c251c9aa-04af-41a9-a4b1-7abb4a3b77b7&enrichSource=Y292ZXJQYWdlOzI2NTM3NjgxMjtBUzoxMzgxMTc2MzgwMDQ3MzZAMTQwOTk0MTIxOTEwMA%3D%3D&el=1_x_4https://www.researchgate.net/?enrichId=rgreq-c251c9aa-04af-41a9-a4b1-7abb4a3b77b7&enrichSource=Y292ZXJQYWdlOzI2NTM3NjgxMjtBUzoxMzgxMTc2MzgwMDQ3MzZAMTQwOTk0MTIxOTEwMA%3D%3D&el=1_x_1https://www.researchgate.net/publication/265376812_Letter_to_Obinichi_Nnorom_some_ICEM_mesh_generation_guidelines?enrichId=rgreq-c251c9aa-04af-41a9-a4b1-7abb4a3b77b7&enrichSource=Y292ZXJQYWdlOzI2NTM3NjgxMjtBUzoxMzgxMTc2MzgwMDQ3MzZAMTQwOTk0MTIxOTEwMA%3D%3D&el=1_x_3https://www.researchgate.net/publication/265376812_Letter_to_Obinichi_Nnorom_some_ICEM_mesh_generation_guidelines?enrichId=rgreq-c251c9aa-04af-41a9-a4b1-7abb4a3b77b7&enrichSource=Y292ZXJQYWdlOzI2NTM3NjgxMjtBUzoxMzgxMTc2MzgwMDQ3MzZAMTQwOTk0MTIxOTEwMA%3D%3D&el=1_x_2

  • 8/18/2019 ICEM Mesh Generation

    2/8

     

    Dear Obinichi,

    There are many ways to do this type of mesh, this is one that I consider easy to

    undestand the process.

    Start from a 2D surface block as shown in the Figure. Select the options and the

    surface.

    In the Block Menu, you must subdivide the edges as you think better, according to

    your case.

  • 8/18/2019 ICEM Mesh Generation

    3/8

     

    You can copy a edge parameters to its neighbors edges, fill each one. The

    spacements and laws are from your taste.

    Select Pre-mesh to preview.

  • 8/18/2019 ICEM Mesh Generation

    4/8

     

    It needs an O-grid.

    Select the o-grid and a good off set according to your case

    Again, subdivide the new edge. Choose a properly spacement according to your Y+

  • 8/18/2019 ICEM Mesh Generation

    5/8

     

    Select Pre-mesh and generate an unstructured mesh as is shown in the Figures

  • 8/18/2019 ICEM Mesh Generation

    6/8

     

    In the mesh menu select Extrude Mesh. Select the surface elements. An d in the

    part names you can set as default, or rename each part. My curve path was the

    axial curve.

  • 8/18/2019 ICEM Mesh Generation

    7/8

     

    Chosse a good number of layers to capture the curvature. The result is shown in

    the Figures.

    My release is 12.1 there are better tools in the new releases. This is a very simple

    example. The geometry would must be subdivided in minor segments, because in

    the ICEM the geometric elements are parametric, and the curves have a normal,

    torsion and tangent vectors that driven the swept direction , and some distortions

    can happen.

  • 8/18/2019 ICEM Mesh Generation

    8/8

    A sequence of 3D blocks extruded is also possible and probably the better choice,

    but it is need more knowledge. But is feasible.

    I suggest to see:

    https://www.youtube.com/watch?v=LHmuBVrW35w#t=106 

    Bests!!

    Ricardo V. P Rezende, Ph.D.

    https://www.youtube.com/watch?v=LHmuBVrW35w#t=106https://www.youtube.com/watch?v=LHmuBVrW35w#t=106https://www.youtube.com/watch?v=LHmuBVrW35w#t=106