Upload
others
View
0
Download
0
Embed Size (px)
Citation preview
Edition 4 / Revision 0 TRANSPORT FOR NSW
September 2020
TRANSPORT FOR NSW (TfNSW)
QA SPECIFICATION B345
BRIDGE NAMEPLATES AND NUMBER PLATES
NOTICE
This document is a Transport for NSW QA Specification. It has been developed for use with
roadworks and bridgeworks contracts let by Transport for NSW or by local councils in NSW. It is not
suitable for any other purpose and must not be used for any other purpose or in any other context.
Copyright in this document belongs to Transport for NSW.
REVISION REGISTER
Ed/Rev
Number
Clause
Number Description of Revision
Authorised
By Date
Ed 1/Rev 0 All First issued based on TRDM-0013-SPN -
Manufacture and Delivery of Bridge Name
Plate (07.07.93).
GM, RNIC 05.05.00
Ed 2/Rev 0 All Numbering of plates added. All drawings
changed
GM, RNIC 12.05.00
Ed 2/Rev 1 3
Guide
Mounting for pedestrian railings and
Drawing RTAB042B added.
All drawings changed
A/GM,
RNIC
01.06.00
Ed 2/Rev 2 Guide All drawings changed
Contact details changed
GM, RNIC 12.02.03
Ed 3/Rev 0 Guide Notes List of bridge nameplate drawings updated.
Drawings previously attached removed.
Requirements for printing of drawings and
contact details deleted. RTA website
addresses for drawings added.
GM, IC 29.08.08
Various New clauses and subclauses. References
transferred to Annexure B345/M. Types of
bridge nameplates updated.
3 Last paragraph drawing references updated.
Annexures Annexures added.
Ed 3/Rev 1 2.1 Alternative copper alloy C92610A for bridge
nameplates added.
GM, IC 08.06.11
Ed 3/Rev 2 Guide Notes Number of name plate classifications reduced
to four. All referenced SBD numbers
revised.
GM, IC 04.04.12
2 Number of name plate classifications reduced
to four. All referenced SBD numbers
revised.
Ed 3/Rev 3 Global References to “Roads and Maritime
Services” or “RMS” changed to “Transport
for NSW” or “TfNSW” respectively.
DCS 22.06.20
ii
Ed/Rev
Number
Clause
Number Description of Revision
Authorised
By Date
Ed 4/Rev 0 Global Clauses rearranged and reworded to improve
clarity.
Spec title changed.
EDCS 25.09.20
Guide Notes Guide Notes amended. List of Standard
Bridge Drawings deleted. Link to Standard
Bridge Drawings updated.
1.1 Statement added that scope includes
installation where applicable.
2 New clause titled “Types and Quantity”.
Type designation A to D no longer used.
2.1 New clause incorporating previous clause 4,
and clauses 2.2 to 2.6. Drawing numbers for
each plate type updated and tabulated.
2.2 New clause titled “Quantity”.
3 New clause titled “Manufacture”.
3.2 Previously clause 7.
3.3 New clause titled “Materials”, incorporating
material requirements from previous clause
2.1 and 3. Particular catalogue items no
longer specified.
3.4 New clause titled “Casting and Finishing”,
incorporating part of previous clause 2.1.
3.5 New clause titled “Attachment Accessories”,
replacing previous clause 3.
4 New clause titled “Packaging and Delivery”,
incorporating previous clauses 4 and 5.
5 New clause titled “Installation”. Statement
added that this clause applies only when
installation forms part of contract.
5.1 Drawing numbers for installation updated
and tabulated.
5.2 New clause titled “Mounting – New or
Additional Plates”, incorporating parts of
previous clauses 2.4 and 2.6.
6 New clause combining previous clauses 8
and 9.
iii
GUIDE NOTES (Not Part of Contract Document)
TfNSW Standard Bridge Drawings B0700 Nameplate series are applicable to this Specification.
These Drawings are available on the TfNSW’s Internet website at
https://www.rms.nsw.gov.au/business-industry/partners-suppliers/document-types/standard-
drawings/bridge/index.html
For construction contracts, the Tender Documenter must include the relevant Standard Bridge
Drawings as part of the Supplementary Drawings of the Tender Documents.
https://www.rms.nsw.gov.au/business-industry/partners-suppliers/document-types/standard-drawings/bridge/index.htmlhttps://www.rms.nsw.gov.au/business-industry/partners-suppliers/document-types/standard-drawings/bridge/index.html
Edition 4 / Revision 0 TRANSPORT FOR NSW
September 2020
QA SPECIFICATION B345
BRIDGE NAMEPLATES
AND NUMBER PLATES
Copyright – Transport for NSW
IC-QA- B345
VERSION FOR:
DATE:
Bridge Nameplates and Number Plates B345
Ed 4 / Rev 0 i
CONTENTS
CLAUSE PAGE
FOREWORD ............................................................................................................................................... II TfNSW Copyright and Use of this Document ............................................................................... ii Revisions to Previous Version ....................................................................................................... ii Project Specific Changes ............................................................................................................... ii
1 GENERAL ........................................................................................................................................ 1 1.1 Scope .............................................................................................................................. 1 1.2 Structure of the Specification ......................................................................................... 1
2 TYPES AND QUANTITY ................................................................................................................... 1 2.1 General ........................................................................................................................... 1 2.2 Quantity .......................................................................................................................... 2
3 MANUFACTURE .............................................................................................................................. 2 3.1 General ........................................................................................................................... 2 3.2 Manufacturing Facility ................................................................................................... 2 3.3 Materials ......................................................................................................................... 2 3.4 Casting and Finishing ..................................................................................................... 2 3.5 Attachment Accessories ................................................................................................. 3
4 PACKAGING AND DELIVERY .......................................................................................................... 3
5 INSTALLATION ............................................................................................................................... 3 5.1 Mounting - General ........................................................................................................ 3 5.2 Mounting - New or Additional plates ............................................................................. 4
\ QUALITY RECORDS AND WARRANTY ............................................................................................ 4 6.1 Quality Records .............................................................................................................. 4 6.2 Warranty ......................................................................................................................... 4
ANNEXURES B345/A TO B345/B – (NOT USED) ...................................................................................... 5
ANNEXURE B345/C – SCHEDULE OF IDENTIFIED RECORDS .................................................................... 5
ANNEXURES B345/D TO B345/L – (NOT USED) ...................................................................................... 5
ANNEXURE B345/M – REFERENCED DOCUMENTS .................................................................................. 5
LAST PAGE OF THIS DOCUMENT IS ............................................................................................................ 5
B345 Bridge Nameplates and Number Plates
ii Ed 4 / Rev 0
FOREWORD
TFNSW COPYRIGHT AND USE OF THIS DOCUMENT
Copyright in this document belongs to Transport for New South Wales.
When this document forms part of a contract
This document should be read with all the documents forming the Contract.
When this document does not form part of a contract
This copy is not a controlled document. Observe the Notice that appears on the first page of the copy
controlled by TfNSW. A full copy of the latest version of the document is available on the TfNSW
Internet website: http://www.rms.nsw.gov.au/business-industry/partners-
suppliers/specifications/index.html
REVISIONS TO PREVIOUS VERSION
This document has been revised from Specification TfNSW B345 Edition 3 Revision 3.
All revisions to the previous version (other than minor editorial and project specific changes) are
indicated by a vertical line in the margin as shown here, except when it is a new edition and the text
has been extensively rewritten.
PROJECT SPECIFIC CHANGES
Any project specific changes are indicated in the following manner:
(a) Text which is additional to the base document and which is included in the Specification is
shown in bold italics e.g. Additional Text.
(b) Text which has been deleted from the base document and which is not included in the
Specification is shown struck out e.g. Deleted Text.
http://www.rms.nsw.gov.au/business-industry/partners-suppliers/specifications/index.htmlhttp://www.rms.nsw.gov.au/business-industry/partners-suppliers/specifications/index.html
(TfNSW COPYRIGHT AND USE OF THIS DOCUMENT - Refer to the Foreword after the Table of Contents)
Ed 4 / Rev 0 1
TfNSW QA SPECIFICATION B345
BRIDGE NAMEPLATES AND NUMBER PLATES
1 GENERAL
1.1 SCOPE
This Specification sets out the requirements for the supply of bridge nameplates and number plates,
and associated fixing components.
It also sets out the requirements for installation of the nameplates or number plates where the Contract
includes their installation.
This Specification does not cover the supply of bridge opening plaques.
1.2 STRUCTURE OF THE SPECIFICATION
This Specification includes a series of annexures that detail additional requirements.
1.2.1 Schedule of Identified Records
The records listed in Annexure B345/C are Identified Records for the purposes of Specification
TfNSW Q Annexure Q/E.
1.2.2 Referenced Documents
Unless otherwise specified, the applicable issue of a referenced document, other than an TfNSW
Specification, is the issue current at the date one week before the closing date for tenders, or where no
issue is current at that date, the most recent issue.
Standards, specifications and test methods are referred to in abbreviated form (e.g. AS 1234). For
convenience, the full titles are given in Annexure B345/M.
2 TYPES AND QUANTITY
2.1 GENERAL
The design of nameplates and number plates is controlled by the Principal. Do not modify the designs
without a written approval from the Principal.
The material, dimensions, legend and countersunk hole details of the different types of bridge
nameplates and number plates, and their associated fixing screws and bolts, must be in accordance
with the Standard Bridge Drawings shown in Table B345.1, except for the bridge numbers and year
which will be different for different bridges.
(TfNSW COPYRIGHT AND USE OF THIS DOCUMENT - Refer to the Foreword after the Table of Contents)
B345 Bridge Nameplates and Number Plates
2 Ed 4 / Rev 0
Table B345.1 – Applicable Standard Bridge Drawings for
Nameplate and Number Plate
Type of Nameplate or Number Plate Standard Bridge Drawing
Nameplates on new bridges or culverts B0701
Replacement nameplates on widened bridges or culverts B0702
Additional nameplates on widened bridges or culverts B0703
Nameplates on modified bridges or culverts B0704
Bridge number plates on existing bridges or culverts B0705
2.2 QUANTITY
Provide the number of nameplates or number plates as shown on the Drawings, or as stated on the
manufacturing order.
Where not shown on the Drawings, provide a replacement nameplate where the original nameplate is
removed during widening of bridges or culverts or where there is no original nameplate on the
widened bridges or culverts.
Where not shown on the Drawings, provide an additional nameplate where the original nameplate is
retained on widened bridges or culverts in close proximity to the original nameplate.
3 MANUFACTURE
3.1 GENERAL
Manufacture the bridge nameplates and number plates to the details shown in the applicable TfNSW
Standard Bridge Drawing shown in Table B345.1.
3.2 MANUFACTURING FACILITY
Provide certification that the supplier of the nameplates and number plates has control or ownership of
a facility which has the capacity to manufacture a wide variety of cast metal products.
3.3 MATERIALS
The copper alloy for the casting of the plates must be C92610A or C92710 to AS 1565, as specified in
the relevant Standard Bridge Drawing.
Fixing screws and bolts must be made of commercial grade brass, with a minimum strength of 250
MPa.
3.4 CASTING AND FINISHING
Use a pattern for casting of the plates which, unless it is provided by the Principal, will require a new
pattern to be specially made by the manufacturer.
(TfNSW COPYRIGHT AND USE OF THIS DOCUMENT - Refer to the Foreword after the Table of Contents)
Bridge Nameplates and Number Plates B345
Ed 4 / Rev 0 3
The bridge numbers and year to be cast will be specified on the Drawings or manufacturing order, and
must be of the same font as the lettering shown on the Drawings.
After casting, polish the raised portion of the face and the edges of the plates.
3.5 ATTACHMENT ACCESSORIES
Provide concrete inserts to attach nameplates to concrete structures which are to be constructed under
the Contract. Provide expanding masonry anchors to fix nameplates or number plates to existing
concrete structures.
4 PACKAGING AND DELIVERY
Pack all finished items to prevent scratching of the surfaces and damage to threads.
Pack nameplates and number plates separately from the fixing screws or bolts. Where more than one
nameplate or number plate has been ordered, pack them separately.
Where the Contract is for supply only, the delivery address, which may be anywhere in New South
Wales, will be stated on the manufacturing order.
5 INSTALLATION
This clause applies only when installation forms part of the Contract.
5.1 MOUNTING - GENERAL
Mount the nameplates and number plates on various elements in the manner and location in
accordance with the Standard Bridge Drawings shown in Table B345.2.
Table B345.2 – Applicable Standard Bridge Drawings for
Mounting on Various Elements
Element Standard Bridge Drawing
Concrete parapet B0706, B708
Steel pedestrian/cycle railing B0707, B708
Lift shaft B0707, B708
Culvert wingwall B0707, B708
For nameplates attached to concrete structures which are to be constructed under the Contract, install
them recessed in the concrete so that it is set flush with the concrete surface.
For nameplates and the number plates which are to be fixed to existing concrete structures, mount
them proud of the concrete surface.
Drill and tap holes and use screws to fix nameplates or number plates to pedestrian/cycle bridge steel
railings.
(TfNSW COPYRIGHT AND USE OF THIS DOCUMENT - Refer to the Foreword after the Table of Contents)
B345 Bridge Nameplates and Number Plates
4 Ed 4 / Rev 0
5.2 MOUNTING - ADDITIONAL NAMEPLATE OR NEW NUMBER PLATE
Where an additional nameplate is required for widened bridge or culvert, or where a new number plate
is required for an existing bridge or culvert, install the new plate in close proximity to the existing
nameplate.
If the existing bridge or culvert has no nameplate, mount the number plate in the same manner as a
nameplate.
6 QUALITY RECORDS AND WARRANTY
6.1 QUALITY RECORDS
Maintain quality records for the despatched items. Record the actual grade of copper alloy for each
finished item.
6.2 WARRANTY
Provide a minimum warranty period of six months for the nameplates and number plates covering
defective workmanship, material and process.
No warranty is required against vandalism or accidental damage.
(TfNSW COPYRIGHT AND USE OF THIS DOCUMENT - Refer to the Foreword after the Table of Contents)
Bridge Nameplates and Number Plates B345
Ed 4 / Rev 0 5
ANNEXURES B345/A TO B345/B – (NOT USED)
ANNEXURE B345/C – SCHEDULE OF IDENTIFIED RECORDS
Refer to Clause 1.2.1.
The records listed below are Identified Records for the purposes of TfNSW Q Annexure Q/E.
Clause Description of Identified Record
6.1 Quality records
ANNEXURES B345/D TO B345/L – (NOT USED)
ANNEXURE B345/M – REFERENCED DOCUMENTS
Refer to Clause 1.2.2.
TfNSW Specifications
TfNSW Q Quality Management System
Australian Standards
AS 1565 Copper and copper alloys – Ingots and castings