IAT Video Encoder Setup User ManualIAT Video Encoder Setup User Manual 01/04/2018 revision [email protected]

IAT Video Encoder Setup User Manual

01/04/2018 revision

[email protected] www.iat101.com www.peephole-store.com www.ezdiybroadcast.com

Typical setting for wired connection for live streaming

1.) LAN StreamingIPTV, NVR/ Teaching /Campus

Broadcast/ Hotel TV system,

Surveillance/ Video Conference,

and more…

Check your Router IP address before an encoderUsing web browser and input following IP address to see which IP address showing in your router User Interface such that you don’t need to change your router IP address as you setting the encoder

192.168.0.1 or 192.168.1.1

RTMP to Social Media

2. ) WAN Streaming

a PC or a smartphone

used for access the

encoder externally for

live streaming settings

H.264 or H.265 encoder

Video Sources

HDMI or SDI

signal in

RJ45 cable

Router

[email protected] www.iat101.com www.peephole-store.com www.ezdiybroadcast.com1

1.) Use IE or Google Web Browser to check your Router IP address is 192.168.0.1 or 192.168.1.1

• If your router using none of these 2 IP address, Please contact seller or system administrator to find your Router IP address• If you prefer not to change your router IP address, you may log into encoder’s UI, and change encoder’s IP address to matching your

router IP address. However, please be noted every time you clicking the encoder reset button, it will get back to its default IP address

For example, I found my router is 192.168.0.1, and then I Check the my encoder’s default IP address, if its default IP

address 192.168.0.31, please go on for the encoder settings. If my encoder’s default IP address is 192.168.1.168 then

you have to log into your Router’s UI (user interface) and change router’s IP to 192.168.1.1

Note: If you prefer not to change your router IP address, you may log into encoder’s UI, and change encoder’s IP address.

However, please be noted every time you clicking the encoder reset button, it will get back to its default IP address


[email protected] www.iat101.com www.peephole-store.com www.ezdiybroadcast.com

Once Router IP address checking done, now is checking your PC’s IP address

Click internet access

Click

Open Network and Sharing Center

Click Local Area Connection

Click Details

This is your PC’s IP address information

Copy it down for input into your encoder

3

If you like to change your PC’s IP address, you may use following to change it

Click Properties Select Internet Protocol Version 4 (TCP/IPv4), and

then click Properties

1

2

Now, you can change your PC’s IP

address information here!


Another way to change PC’s IP address, and the result should be as same as previous page

5 [email protected] www.iat101.com www.peephole-store.com www.ezdiybroadcast.com

Now, use web browser log into encoder’s UI


Click Main Stream

for

LAN

se

ttin

gs

for

WA

N s

ett

ing

s

7

Use VLC Media Player ( Free software) to verify if the LAN setting is working

Select Open Network Stream

Input a correct LAN URL, ie

rtsp://192.168.0.31:554/main

VLC media player showing the LAN streaming video


How to get YouTube’s streaming key settings (for WAN settings)

First log into your YouTube or Facebook and obtain the live streaming URL and streaming key

Youtube� Creator Studio / Live streaming


How to get Facebook’s streaming key settings (for WAN settings)

First log into your Facebook account, and then link to

https://www.facebook.com/live/create , click Create Live Stream

and then obtain the live streaming URL and streaming key as shown in the following

xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx

For Facebook to starting live steaming, please click Go Live


How to put the live streaming information into encoder’s RTMP field?

Encoder RTMP field for WAN settings

Example

YouTube’s URL � rtmp://a.rtmp.youtube.com/live2

YouTube’s Streaming key� xxxx(16 digi stream key) xxxx

FaceBook’s Server URL� rtmp://live-api.facebook.com:80/rtmp/

Facebook’s streaming key � 2019x602x025x69?ds=1xa=AxhfxR5xDcUuxBdx

YouTube Facebook

a.rtmp.youtube.com live-api.facebook.com:80

1935 1935

live2 rtmp

xxxx(16 digi stream key) xxxx 2019x602x025x69?ds=1xa=AxhfxR5xD

cUuxBdx

* Please make sure to Enable, and save Setup, and then to Reboot (under System panel)


Q&A A.) How come I can only use FLV to view the video in LAN settings, but not able to see

Live streaming in WAN (in YouTube or Facebook)?

Ans: for most of case is your router IP address is not as same as your PC’s IP address.

You will have to change either one of the IP address to make the whole setting with consistent IP address. For example as followings

B.) I am able to live streaming to YouTube but it gets disconnected automatically within 5 to 10 min and YouTube show error of "OFFLINE" AND SHOW

DATA NOT RECEIVING?

Ans: For most of case, you may like to double check your internet bandwidth over some period of time using the free software Speed Test to ensure

your video transmission system is good and stable having enough bandwidth for live streaming to YouTube or Facebook.

Also you may like to try followings,

1.) for video setting, please try to fix the video source with fixed video format (such as 720P with 30F/s or 720P with 60F/s), and for encoder's output

video please also try to set as 720P with 30F/s.

2.) set audio at AAC 48000 sample

3.) It is also better to check the video source keeps sending stable video to the encoder.

4.) If you also using the splitter during the live streaming, please make sure having a stable power source for the switch.

5.) During live streaming, please don't use PC to browsing internet that would causing the router transmission bandwidth fluctuations.

6.) If your video source is a motion-detect or a timing device that stopping sending video to encoder that would also causing no data, and then offline.

7.) If you are using a WiFi encoder for live streaming, please avoid the wireless “Dead Zone”.

If your WiFi setting is within or near a “Dead Zone” area, the live streaming will be stopped due to no signal transmission. A common mistake in no

signal during live streaming is due to no WiFi signal transmission in a Dead Zone area. It is not due to the encoder not working.

* Reading in WiFi Dead Zone, you may referring to following web link or Google the key words “WiFi Dead Zone”

www.makeuseof.com/tag/what-is-a-wireless-dead-zone-and-how-to-eliminate-it/

Encoder default

IP address

Router IP

address

PC’s IP address &

Default gateway

Preferred DNS Server

Alternate DNS Server

192.168.0.31 192.168.0.1 192.168.0.99

192.168.0.1

192.168.0.168

8.8.8.8

192.168.1.168 192.168.1.1 192.168.1.99

192.168.1.1

192.168.1.96

8.8.8.8


Documents

IAT Video Encoder Setup User ManualIAT Video Encoder Setup User Manual 01/04/2018 revision [email protected]