Upload
lalitendujena
View
280
Download
0
Embed Size (px)
Citation preview
7/21/2019 IA NT PWR 2.0 Reference Guide
http://slidepdf.com/reader/full/ia-nt-pwr-20-reference-guide 1/92
June 2010Copyright © 2010 ComAp s.r.o.Written by Vlastimil Vostř ákPrague, Czech Republic
ComAp, spol. s r.o.Kundratka 2359/17, 180 00 Praha 8, Czech RepublicTel: +420 246 012 111, Fax: +420 246 316 647E-mail: [email protected], www.comap.cz
Reference Guide
Automatic Transfer Switch Controller
SW version 2.0, June 2010
InteliATSNT
IA-NT PWR unit
7/21/2019 IA NT PWR 2.0 Reference Guide
http://slidepdf.com/reader/full/ia-nt-pwr-20-reference-guide 2/92
InteliATSNT PWR, SW version 2.0, ©ComAp – June 2010 2IA-NT- PWR-2.0-Reference Guide.pdf
ts
..................... 2
..................... 4
..................... 4 4
..................... 4
..................... 5
..................... 5
..................... 7
..................... 7
..................... 9
..................... 9
................... 10
................... 13
................... 13
................... 14
................... 14
................... 17
................... 17
................... 18
................... 19
................... 19
................... 20
................... 21
................... 22
................... 22
................... 23
................... 24
................... 25
................... 26
................... 27
................... 28
................... 31
................... 31
................... 33
................... 33
................... 34
................... 34
................... 38
................... 40
................... 41 ................... 41
................... 43
................... 43
................... 49
................... 49
................... 49 Engine Params.................................................................................................................................. 57 Gener Protect.................................................................................................................................... 60 AMF Settings..................................................................................................................................... 62 Sync Ctrl............................................................................................................................................ 66 Date/Time.......................................................................................................................................... 67 SMS/E-Mail ....................................................................................................................................... 68
Function Description.............................................................................................................................. 70 Operating modes............................................................................................................................... 70 Circuit breakers timing ...................................................................................................................... 73
Table of Conten
Table of Contents ...............................................................................................................Document information ........................................................................................................
Clarification of notation...................................................................................................Text .....................................................................................................................................................Conformity Declaration...................................................................................................
General Guidelines.............................................................................................................What is in this manual? ..................................................................................................
Description..........................................................................................................................Description of the controller system...............................................................................Configurability.................................................................................................................
.What is in the package?..... ...........................................................................................IL-NT RS232 Communication module ...........................................................................IL-NT RS232-485 Communication module....................................................................IL-NT S-USB Service USB communication module.......................................................IL-NT RD Remote display software ...............................................................................IB-Lite Communication module......................................................................................IL-NT BIO8 Hybrid binary input/output module..............................................................Programming of IA-NT controller ...................................................................................
User Interface .....................................................................................................................Terminals............................................................................................................................
IA-NT PWR terminals and face ......................................................................................Recommended Wiring........................................................................................................
IA-NT PWR – Wiring Diagram......................................................................................... . Applications .................. .............................................................................................. ......
AMF using two separate breakers with feedbacks (MCB and GCB)............................. AMF using two separate breakers with feedbacks (MCB and GCB) + Test on Load.... AMF using two-position ATS with feedback................................................................... AMF using three-position ATS with feedbacks .............................................................. AMF + manual transfer & neutral control using three-position ATS ..............................
. AMF + no battery operation .......................... ................................................................Controllers in cascade....................................................................................................
Getting Started ...................................................................................................................How to install ..................................................................................................................IL-NT BIO8 extension module connection .....................................................................Current measurement ....................................................................................................CT location .....................................................................................................................Voltage measurement and generator connection types ................................................RS485 connection..........................................................................................................
Inputs and Outputs .............................................................................................................Binary inputs IA-NT - default ..........................................................................................Binary inputs – list ..........................................................................................................Binary outputs IA-NT - default........................................................................................Binary outputs - list .........................................................................................................
Setpoints.............................................................................................................................Password........................................................................................................................Basic Settings.................................................................................................................
7/21/2019 IA NT PWR 2.0 Reference Guide
http://slidepdf.com/reader/full/ia-nt-pwr-20-reference-guide 3/92
InteliATSNT PWR, SW version 2.0, ©ComAp – June 2010 3IA-NT- PWR-2.0-Reference Guide.pdf
................... 75
................... 75
................... 75
................... 75
................... 76
................... 76
................... 77 ................... 78
................... 78
................... 79
................... 80
................... 80
................... 80
................... 80
................... 84
................... 84
................... 84
................... 84
................... 84
................... 85 ................... 85
................... 85
................... 85
................... 86
................... 88
................... 88
................... 89
................... 89
................... 90
................... 90
................... 90
................... 90
................... 90 ................... 91 Binary inputs and outputs.................................................................................................................. 91 IL-NT RS232 interface (optional card) .............................................................................................. 91 IL-NT RS232-485 interface (optional card) ....................................................................................... 92 IL-NT S-USB interface (optional card) .............................................................................................. 92 IB-Lite interface (optional card)......................................................................................................... 92 IL-NT BIO8 extension module (optional card)................................................................................... 92
Alarm Management ............................................................................................................Warning (WRN) ..............................................................................................................
.Trip (TRP)................................................................................................................ ......Mains failure (MF) .......................................................................................................... AMF time chart – genset OK.......................................................................................... AMF time chart – genset not started properly................................................................
Voltage phase sequence detection................................................................................Gen-set Operation States...................................................................................................List of possible events....................................................................................................History file.......................................................................................................................
Remote Control and Data Logging.....................................................................................Direct connection to the PC ...........................................................................................PC software – LiteEdit....................................................................................................Modbus protocol.............................................................................................................
Remote Communication.....................................................................................................Internet connection.........................................................................................................Recommended ISDN modem ........................................................................................Recommended GSM modem.........................................................................................Mobile SIM card setting..................................................................................................
IL-NT-RD Remote display software....................................................................................General description........................................................................................................Warning!.........................................................................................................................
.IL-NT-RD Software installation................................................................................ ......IL-NT-RD Wiring.............................................................................................................Function description.......................................................................................................SW compatibility.............................................................................................................
Maintenance.......................................................................................................................Backup battery replacement ..........................................................................................
Technical Data....................................................................................................................Inputs/Outputs overview.................................................................................................Power supply..................................................................................................................Operating conditions ......................................................................................................
Dimensions and weight..................................................................................................Mains and generator ......................................................................................................
7/21/2019 IA NT PWR 2.0 Reference Guide
http://slidepdf.com/reader/full/ia-nt-pwr-20-reference-guide 4/92
InteliATSNT PWR, SW version 2.0, ©ComAp – June 2010 4IA-NT- PWR-2.0-Reference Guide.pdf
ion
EFERENCE GUIDE
12111, FAX: +420266316647.COMAP.CZ
Document informat
INTELI ATSNT
PWR®
- RWRITTEN BY: VLASTIMIL VOSTŘ ÁK
©2009-2010 COM AP LTD.KUNDRATKA 17, PRAHA 8, CZECH REPUBLIC PHONE: +4202460WEB: HTTP://WWW , E F-MAIL: IN [email protected]
DOCUMENT HISTORY
REVISION NUMBER RELATED SW. VERSION D ATE
1 1.0 22.02.2009
2 1.0.1 24.03.2009
3 1.2 09.01.2010
4 2.0 09.06.2010
Clarification of notation
NOTE: This type of paragraph calls readers attention to a notice or related theme.
C AUTION! This type of paragraph highlights a procedure, adjustment etc., which can cause a damage or
unproper function of the equipment if not performed correctly and may not be clear at first sight.W ARNING! This type of paragraph indicates things, procedures, adjustments etc. which need high level ofattent th ause personal injury or death.ion, o erwise can c
Text
PAGE (Capital letters in the frame) buttons on the front panelBreak Return (Italic) set pointsGenera
REMO
Conformity Declaration
tor protections (Bold) Set point groupTE START/STOP (Capital letters) binary inputs and outputs
The following escribed m plies with the appropriate basic safety andhealth requirement of the EC Low Voltage Directive No: 73/23 / EEC and ECElectromagnetic Compatibility Directive 89/336 / EEC based on its design and type,as brought into circulation by us.
d achine com
7/21/2019 IA NT PWR 2.0 Reference Guide
http://slidepdf.com/reader/full/ia-nt-pwr-20-reference-guide 5/92
InteliATSNT PWR, SW version 2.0, ©ComAp – June 2010 5IA-NT- PWR-2.0-Reference Guide.pdf
esGeneral Guidelin
What is in this manual?
This manual describes the InteliATSNT PWR (IA-NT-PWR) software, which is designed for automatics and provides general information on how to install and operate the
• Automatic transfer switch panel buildersotely from InteliATSNT)
d maintenance of the gen-set
NT ns of theT-STD-HW_1.3-.AIL) form the
higher too, which is ATSNT SW must berature ATS controller.
transfer switch applicationIn li NTte ATS controller.
This manual is dedicated for
• Operators of remote gen-sets (started rem• For everybody who is concerned with installation, operation an
InteliATS controller SW and HW versions compatibility
Software InteliATSNT is compatible with the InteliATSNT hardware v. 1.3 and higher.
There are two modifications of the InteliATS HW - STD and PWR and two modificatioInteliATSNT SW – STD and HW which together with the appropriate archive file (IA-NX.X.AIL for STD HW 1.3, IA-NT-STD-X.X.AIL for STD HW > 1.3 and IA-NT-PWR-X.XInteliATSNT PWR or STD controller.
Beside that the InteliATSNT software is compatible with IL-NT AMF HW 1.3 andused when a low temperature ATS application is needed. In this case the Intelicombined (purchased) with the IL-NT AMF 25 LT HW to obtain the low tempe NOTE:Because of large variety of InteliATSNT parameters settings, it is not possible to describe anycombination. Some of InteliATSNT functions are subject of changes depend on SW version.The data in this manual only describes the product and are not warranty of performance orcharacteristic.
C AUTION!SW and HW must be compatible (e.g. IA-NT firmware and IA-NT HW) otherwise the function will bedisabled. If wrong software is downloaded, message HARDWARE INCOMPATIBLE appears oncontroller screen. In this case use Boot load (jumper) programming – close Boot jumper and followinstructions in LiteEdit, download correct software.
NOTE:C rmation provided herein is correct and reliable and reserves the right toomAp believes that all infou omAp does not assume any responsibility for its use unless otherwise expresslypdate at any time. Cundertaken.
W ARNING!Remote control - InteliATSNT controller can be remotely controlled. In case of the work on thecontrolled devices check, that nobody can perform remote operation.To be sure disconnect
- remote control via RS232 line- input REM TRANSFER- input REMOTE AUT- input REMOTE TEST
or disconnect output Rem START/ST tputs GCB CLOSE/OPEN and MCB CLOSE/OPENOP and ou
7/21/2019 IA NT PWR 2.0 Reference Guide
http://slidepdf.com/reader/full/ia-nt-pwr-20-reference-guide 6/92
InteliATSNT PWR, SW version 2.0, ©ComAp – June 2010 6IA-NT- PWR-2.0-Reference Guide.pdf
W ARNING!E wing InteliATSNT controller terminals:very time you want to disconnect follo d / or- Mains voltage measuring an - Binary output for MCB control and / or
- MCB FeedbackSwitch InteliATS to MAN or OFF Mode or disconnect the Binary outputs Rem Start/Stop and GCBNT
Close/Open to avoid unexpected automatic start of gen-set and GCB closing.
W ARNING!
Dangerous vol tage
In no case touch the terminals for voltage and current measurement!
Always connect grounding terminals!
In any case do not disconnect InteliATS current transformer terminals!NT
The following instructions are for qualified personnel only. To avoid personal injury do notperform any action not specified in this Reference guide!!!
7/21/2019 IA NT PWR 2.0 Reference Guide
http://slidepdf.com/reader/full/ia-nt-pwr-20-reference-guide 7/92
InteliATSNT PWR, SW version 2.0, ©ComAp – June 2010 7IA-NT- PWR-2.0-Reference Guide.pdf
nDescriptio
Description of the controller system
InteliATSNT is a comprehensive Automatic Transfer Switch controller designed to mon AC mains supply (1 or 3 phases) for under & over voltage, under & over frequency anunbalance. In the case of any mains supply disproportion it will send a remote start cogen-set and make changeover for both
itor the incomingd voltagemmand to the
generator and mains contactors. The gen-set requires ast a key-start box
al.
ferent types of changeover (transition)
ssiveze” mains and gen-set
it for the both
oltage and frequencyexpires.
utes/predicts
the MAINS-MAINS applications and not only for theen Start/Stoponfigured/used
tells the controller that the MAINS-GEN application type is to be used. If nottop-fail protection and
ay showing icons, symbols and bar-ether with high functionality, new standards in Gen-set
The key features are:• Easy-to-use operation and installation. Factory default configuration covers most of
applications• Different customer changes are possible thanks to the configurability• Excellent remote communication capabilities• High reliability
remote start type control unit (e.g. the ComAp InteliLiteNT MRS 10 controller), at leawith an external input for the start/stop sign
The controller is capable of providing the following three dif • open delayed transition• open in-pase transition with synch check• closed short-time (100ms) parallel transition with synch check
In order to provide “synch check” the controller has been enhanced by the feature called pasynchronization. The passive sync (sync check) offers possibility to “synchroniwithout the need to use speed regulation or - better to say - it offers possibility to wasources to get in phase.System is evaluated as to be in sync according to the predefined parameters – vdifference – if the both sources will get in-phase before the synchronization timeoutParameters defining breaker delay are taken into the account when the system compexact moment when the both sources are “in phase”.
InteliATSNT controller can be used also forMAINS-GEN applications. The system recognizes application type according to the Gand Gen ReadyToLoad logical binary output and input configuration. If the both are c(default setting) itc fion gured, the MAINS-MAINS application type takes place. In this case the sthe generator current protection are not evaluated.
InteliATSNT controllers are equipped with a powerful graphic displgraphs for intuitive ocontrols.
peration, which sets, tog
7/21/2019 IA NT PWR 2.0 Reference Guide
http://slidepdf.com/reader/full/ia-nt-pwr-20-reference-guide 8/92
InteliATSNT PWR, SW version 2.0, ©ComAp – June 2010 8IA-NT- PWR-2.0-Reference Guide.pdf
Example application
7/21/2019 IA NT PWR 2.0 Reference Guide
http://slidepdf.com/reader/full/ia-nt-pwr-20-reference-guide 9/92
InteliATSNT PWR, SW version 2.0, ©ComAp – June 2010 9IA-NT- PWR-2.0-Reference Guide.pdf
Configurability
One of the key features of the controller is high level of adaptability of the system to the needs ofy particular application. The way, how to achieve this, is the configuration.ever
NOTE: Use LiteEdit PC software to read configuration from the controller or disk, view it, modify it and writethe configuration to controller or disk.
The firmware contains a number of binary inputs and outputs needed for all necessaryavailable in the
functionsfirmware. But not all functions are required at the same time on different gen-sets and
also the controller hardware does not have so many input and output terminals. One of the main tasksion is mapping of "logical" firmware inputs and outputs to the "physical" hardware
i
C
1. Mapping of logical binary inputs (functions)
of the configuratnputs and outputs.
onfiguration parts:
or assigning alarms to physical binary input
terminals2. Mapping of logical binary outputs (functions) to physical binary output termin3. Changing language
alsof the controller texts
tandarteEdit software. See
tion for details.
The controller is delivered with a default configuration, which should fit to most sapplications. This default configuration can be changed only using PC and LitLiteEdit documenta
NOTE: You need one of communication modules to connect the controller to a PC with LiteEdit. There is aspecial easy removable service module for cases, where there is no communication modulepermanently attached.
ther controller oris called archive and has file extension ".ail". An archive contains full
image of the controller at the moment of saving (if the controller is online to the PC) except firmware,are also current adjustment of all setpoints, all measured values, a
ist.
ers aring controllers withonfigu
in
Once the configuration is modified, it can be stored in a file for later usage with anofor backup purposes. The file
i.e. besides configuration therecopy of history log and a copy of alarm l
Tidentical c
he archive can be simply use cloning of controllration and settings.
d for , which means prep
What is the package?
Accessories Description Optional / ObligatoryIA-NT PWR InteliATSNT central unit, PWR version Obligatory
IL-NT-RS232 RS232 communication card OptionalIL-NT-RS232-485 RS232 and RS485 communication card OptionalIL-NT-S-USB Service USB communication card Optional
*IL-NT RD Remote display software Optional
IB-Lite Internet commun n idge Optionalicatio br
*Remote display for IA-NT controllers uses standard IL-NT controller with Remote display software
NOTE:
For detailed information about extension modules used with IA-NT controllers, please see the IL-NT,IC-NT, IA-NT, ID-Lite-Accessory Modules manual.
7/21/2019 IA NT PWR 2.0 Reference Guide
http://slidepdf.com/reader/full/ia-nt-pwr-20-reference-guide 10/92
InteliATSNT PWR, SW version 2.0, ©ComAp – June 2010 10IA-NT- PWR-2.0-Reference Guide.pdf
IL-NT RS232 Communication module
NTIL-NT RS232 is optional plug-in card to enable InteliATS for RS232 communication. This is requiredfor computer or Modbus connecting. Card inserts into expansion slot back on the contr To insert the module, you must open the cover first (use screwdriver to open) and then
module into slot. Once you ha
oller.insert the
ve inserted it, the module will snap under plastic teeth. It is supposed tobe installed permanently. Should you need to remove it, the safest way is to remove whole back coverand than remove module manually.
How to install RS 232 communication module:
NOTE: The following procedure is analogic also for other communication modules.
1. Insert a screwdriver into the slot of the cover.
2. Move the screwdriver to set apart the small cover. Be careful!
3. Remove the small cover.
7/21/2019 IA NT PWR 2.0 Reference Guide
http://slidepdf.com/reader/full/ia-nt-pwr-20-reference-guide 11/92
InteliATSNT PWR, SW version 2.0, ©ComAp – June 2010 11IA-NT- PWR-2.0-Reference Guide.pdf
4. Break apart the small cover into two pieces. Do not throw away the smaller part!
5. Take RS 232 communication module.
7/21/2019 IA NT PWR 2.0 Reference Guide
http://slidepdf.com/reader/full/ia-nt-pwr-20-reference-guide 12/92
InteliATSNT PWR, SW version 2.0, ©ComAp – June 2010 12IA-NT- PWR-2.0-Reference Guide.pdf
unication module into the slot of the controller.7. Put back the small cover.6. Plug RS 232 comm
NOTE: When you insert RS 232 communication module, the boot jumper is hidden. For that reason werecommend to use RS 232 communication module with the boot jumper placed on it. See pictures
below:
RS 232 communication module with the boot jumper.
7/21/2019 IA NT PWR 2.0 Reference Guide
http://slidepdf.com/reader/full/ia-nt-pwr-20-reference-guide 13/92
InteliATSNT PWR, SW version 2.0, ©ComAp – June 2010 13IA-NT- PWR-2.0-Reference Guide.pdf
IL-NT RS232-485 Communication module
IL-NT RS232-485 is optional plug-in card to enable InteliATSNT the RS232 and RSThis is required for computer or Modbus connection. Card inserts into expansiocontroller. The IL-NT RS232-485 is a dual port module with RS232 and RS48
485 communication.n slot back on the
5 interfaces at
s analogous.slot. Once you
will snap under plastic teeth. It is supposed to be installed permanently.Should you need to remove it, the safest way is to remove whole back cover and than remove modulemanually.
independent COM channels. The RS232 is connected to COM1 and RS485 to COM2. To insert the module, please follow the instructions for IL-NT RS232 module, procedure iYou must open the cover first (use screwdriver to open) and then insert the module intohave insert it, the module
RS485
RS232Boot jumperRS485 Terminator jumper
IL-NT S-USB Service USB communication module
NTIL-NT S-USB is optional plug-in card to enable InteliATS communication via USB port. This isrequired for computer or Modbus connecting. Card inserts into expansion slot back on the controller.To insert the module, please follow the instructions for IL-NT RS232 module, procedure is analogous.You must open the cover first (use screwdriver to open) and then insert the module into slot. Once youhave inserted it, part of the module will remain over plastic box. It is supposed to be used as a servicetool. When you need to remove it, grab module in cutouts and pull it up manually.
NOTE: Use the shielded USB A-B cable with this module! Recommended is ComAp cable – Order code:“USB-LINK CABLE 1.8M”.
7/21/2019 IA NT PWR 2.0 Reference Guide
http://slidepdf.com/reader/full/ia-nt-pwr-20-reference-guide 14/92
InteliATSNT PWR, SW version 2.0, ©ComAp – June 2010 14IA-NT- PWR-2.0-Reference Guide.pdf
IL-NT RD Remote display software
IL-NT RD is remote display software for a controller. Remote display provides the sammonitoring functions as controller itself. Remote display for IA-NT controllers uses stacontroller with IL-NT Remote display software. No further programing of the display is
is self configurable from the main controller. It is connected with the c
e control andndard IA-NTrequired – unit
ontroller via IL-NT-RS232communication modules using RS232 line. Longer distances (up to 1200m) are possible using IL-NT-2/RS485 converters are used.RS232-485 communication module or when RS23
The IL-NT RD hardware type should fit to the master IA-NT.
NOTE: Please see the “IL-NT-RD Remote display software” chapter for more details.
moduleIB-Lite Communication
IB-Lite is optional plug-in card to enable InteliATSNT communication via Ethernet/Intern
into expansion slot back on the controller.
et. Card inserts
ctions for IL-NT RS232 module, procedure is analogous.river to open) and then insert the module into slot. Once you
have inserted it, part of the module will remain over plastic box. It is supposed to be used as a servicetool. When you need to remove it, grab module in cutouts and pull it up manually.
See IB-Lite-Reference Guide fo r further details.
To insert the module, please follow the instruYou must open the cover first (use screwd
Web server for IB-LiteIs an ew secured way of monitoring and controlling the gen-set from any point in world using your webbrowser. It ofers clear overview and control of the state of engine, its settings and history. Userfriendly.
See IB-Lite-Reference Guide and pictures below for further details.
7/21/2019 IA NT PWR 2.0 Reference Guide
http://slidepdf.com/reader/full/ia-nt-pwr-20-reference-guide 15/92
InteliATSNT PWR, SW version 2.0, ©ComAp – June 2010 15IA-NT- PWR-2.0-Reference Guide.pdf
Scada window:
Measurement window:
7/21/2019 IA NT PWR 2.0 Reference Guide
http://slidepdf.com/reader/full/ia-nt-pwr-20-reference-guide 16/92
InteliATSNT PWR, SW version 2.0, ©ComAp – June 2010 16IA-NT- PWR-2.0-Reference Guide.pdf
Setpoints window:
History window:
HINT:This feature requires IB-Lite optional plug-in module and visible connection of controller to Ethernet.
7/21/2019 IA NT PWR 2.0 Reference Guide
http://slidepdf.com/reader/full/ia-nt-pwr-20-reference-guide 17/92
InteliATSNT PWR, SW version 2.0, ©ComAp – June 2010 17IA-NT- PWR-2.0-Reference Guide.pdf
IL-NT BIO8 Hybrid binary input/output module
ry(version 4.4 and higher) it is possible to easily
Installing IL-NT BIO8 module is similar to installing RS 232 module. The difference is that module fitsto “Extension module” slot and after installing IL-NT BIO8 you do not put back the small cover.
IL-NT BIO8 is optional plug-in card. Through this card controller can accommodate up to 8 binainputs or outputs. In LiteEdit PC configuration toolchoose if particular I/O will be binary input or output.
Programming of IA-NT controller
ming is possible only in OFF mode when the engine is not running.Program NOTE: For more information on programing, see LiteEdit Reference Guide.
C AUTION!
Check the statistic values after firmware upgrade. Readjust the values if necessary.
7/21/2019 IA NT PWR 2.0 Reference Guide
http://slidepdf.com/reader/full/ia-nt-pwr-20-reference-guide 18/92
InteliATSNT PWR, SW version 2.0, ©ComAp – June 2010 18IA-NT- PWR-2.0-Reference Guide.pdf
e
s of displaying
only monitor
sire to change the
Changing the mode of User Interface is possible from default measuring screen of controller bythan press again PAGE. On screen will be
displeyed the choice of two different User Interfaces.
Please see latest IA-NT Operator Guide for detailed description.
User Interfac
There is an interchangable User Interface on controller. It allows two different modecontroller menu.
The first mode called USER is dedicated for users who prefer easy function and needactual values, see alarms or change language settings.Second mode is called ENGINEER and it is dedicated for advaced users, who desettings of controller, monitor all values and check the history of events.
simultaneous pressing the ENTER and PAGE button and
7/21/2019 IA NT PWR 2.0 Reference Guide
http://slidepdf.com/reader/full/ia-nt-pwr-20-reference-guide 19/92
InteliATSNT PWR, SW version 2.0, ©ComAp – June 2010 19IA-NT- PWR-2.0-Reference Guide.pdf
s
IA-NT PWR terminals and face
Terminal
7/21/2019 IA NT PWR 2.0 Reference Guide
http://slidepdf.com/reader/full/ia-nt-pwr-20-reference-guide 20/92
InteliATSNT PWR, SW version 2.0, ©ComAp – June 2010 20IA-NT- PWR-2.0-Reference Guide.pdf
Installation
MountingThe controller is to be mounted onto the switchboard door. Requested cutout size is 175x115mm. Usethe screw holders delivered with the controller to fix the controller into the door as described onpictures below.
7/21/2019 IA NT PWR 2.0 Reference Guide
http://slidepdf.com/reader/full/ia-nt-pwr-20-reference-guide 21/92
InteliATSNT PWR, SW version 2.0, ©ComAp – June 2010 21IA-NT- PWR-2.0-Reference Guide.pdf
ing
IA-NT PWR – Wiring Diagram
Recommended Wir
L 1
L 2
L 3 N
D I E S E L / G A S
R S - 2 3 2 C
I n t e r f a c e
M o d e m o r P C
E N G I N E
G E N E R A T O R
G
L O A D
B .
G e n e r a t o r C .
.
M a i n s C . B
GENREADYTOLOAD
MAINSFAIL BLOCK
REMOTEAUT
GCBFEEDBACK
MCBFEEDBACK
REMOTETEST
REMOTETESTONLD
ALSTARTFAIL
GCBCLOSE/OPEN
GENSTART/STOP
ALM AINSFAIL
ALARM
READYTOAMF
MCBCLOSE/OPEN
CONTROLSIGNALS
+ 2 4 V
0 V
BINARYOUTPUTS
BATTERY
-+
GEN-SETCONTROLLER
NOTE: MCB and GCB is recommended to be mechanically interlocked.
7/21/2019 IA NT PWR 2.0 Reference Guide
http://slidepdf.com/reader/full/ia-nt-pwr-20-reference-guide 22/92
InteliATSNT PWR, SW version 2.0, ©ComAp – June 2010 22IA-NT- PWR-2.0-Reference Guide.pdf
s
plication, where thes for the mains power supply fault and then starts a load transfer process.
Next possible application is manually controlled load transfer between two power supply sources
AMF using two separate breakers wi th feedbacks (MCB and GCB)
Application
The most typical application for the ATS controllers is Auto Mains Failure (AMF) apcontroller watche
(mains x generator).
G
IA-NT
GCB
3x
LOAD
3 x U M
3 x U G
3 x I G
MCB
3x
T 3x
MCB
MCB FEEDBACK
K4
MCB GCB
3x
MCB
K3
GCB
MCB CLOSE/OPEN
GCB CLOSE/OPENBO
BI
GCB FEEDBACK
GCB
en-set start when the mains fails (AUT mode)full control with feedbacks
ak transfer on mains failures return (Load reclosing)
running and waiting for mains failure)
Hardware requirements1x IA-NT PWR
SetpointsMCB Logic = “CLOSE-OFF”
Specification
• Automatic remote g• GCB & MCB• Bre• Break return on main• Test mode (set
7/21/2019 IA NT PWR 2.0 Reference Guide
http://slidepdf.com/reader/full/ia-nt-pwr-20-reference-guide 23/92
InteliATSNT PWR, SW version 2.0, ©ComAp – June 2010 23IA-NT- PWR-2.0-Reference Guide.pdf
two separate breakers with feedbacks (MCB and GCB) +Test on Load AMF using
G
GCB3x
LOAD
3 x U M
3 x U G
3 x I G
MCB3x
T 3x
K4
MCB GCB
K3
3x
BO
BI
IA-NT
MCB
MCB FEEDBACK
GCB
GCB FEEDBACK
TEST ON LOADON LOAD TESTREQUIRED
REMOTE TEST
/CLOSE OPENGCB
MCB CLOSE/ OPEN
ss failure
ins return (Load reclosing)set running and waiting for mains failure)
Load Test - load transfer to gen-set (Island operation) and back to mains in TEST mode onTest on load activation/deactivation. There are 2 breaks in this operation. Controller may
1x IA-NT PWR
SetpointsMCB Logic = “CLOSE-OFF”RetFromIsland = “AUTO” – automatic return (MCB Close) to mains after TESTRetFromIsland = “MANUAL” – mual return to mains (MCB Close) after TEST – IA-NT goes to MAN
mode.
Specification
• Automatic remote gen-set start when the mains fails (AUT mode)• GCB & MCB full kontrol with feedback• Break transfer on main• Break return on ma• Test mode (• On
BIbe forced to TEST mode by BI Remote TEST
Hardware requirements
7/21/2019 IA NT PWR 2.0 Reference Guide
http://slidepdf.com/reader/full/ia-nt-pwr-20-reference-guide 24/92
InteliATSNT PWR, SW version 2.0, ©ComAp – June 2010 24IA-NT- PWR-2.0-Reference Guide.pdf
AMF using two-position ATS with feedback
LOAD
G
IA-NT
3x
3 x U M
3 x U G
3 x I G
3x
T
MCB FEEDBACK
GCB FEEDBACK
3x
MCB CLOSE/OPEN
GCB CLOSE/OPEN
BOBI
K3
3x
ATS
ATS
ATS on "II" position
I II
• -set start when the mains fails (AUT mode)feedback
er on mains failureak return on mains return (Load reclosing)
st mode (set running and waiting for mains failure)
Hardware requirements1x IA-NT PWR
SetpointsMCB Logic = “CLOSE-ON”
Specification
Automatic remote gen• Two-position ATS control with• Break transf • Bre• Te
7/21/2019 IA NT PWR 2.0 Reference Guide
http://slidepdf.com/reader/full/ia-nt-pwr-20-reference-guide 25/92
InteliATSNT PWR, SW version 2.0, ©ComAp – June 2010 25IA-NT- PWR-2.0-Reference Guide.pdf
AMF using three-position ATS wi th feedbacks
G
IA-NT
3x
3 x U M
3 x U G
3 x I G
3x
T
MCB FEEDBACK
GCB FEEDBACK
3x
MCB CLOSE/OPEN
GCB CLOSE/OPEN
BO
BI
LOAD
3x
ATSI II0
ATS
K4K3
ATS on "II" position
ATS on "I" position
• Automatic remote gen-set start when the mains fails (AUT mode)control with feedbacks, pass through neutral position
er on mains failurek return on mains return (Load reclosing)
st mode (set running and waiting for mains failure)
Hardware requirements1x IA-NT PWR
SetpointsMCB Logic = “CLOSE-ON”
Specification
• Three-position ATS• Break transf • Brea• Te
7/21/2019 IA NT PWR 2.0 Reference Guide
http://slidepdf.com/reader/full/ia-nt-pwr-20-reference-guide 26/92
InteliATSNT PWR, SW version 2.0, ©ComAp – June 2010 26IA-NT- PWR-2.0-Reference Guide.pdf
AMF + manual transfer & neut ral control using three-posi tion ATS
G
IA-NT
3x
3 x U M
3 x U G
3 x I G
3x
T
REM TRANSFER
NEUTRAL POS
3x
MCB CLOSE/OPEN
GCB CLOSE/OPEN
BO
BI
LOAD
3x
ATS
ATS
I II0
Force Neutral Position
Manual Load Transfer
K3
K4
K5
NEUTRALPOS
• -set start when the mains fails (AUT mode)control without feedback, pass through neutral position
est for load transfer (AUT mode)quest for switching to neutral position – the highest priority, overrides MCB & GCB state,ces switch to neutral position. After deactivating return to previous state (MCB or GCB)
Hardware requirements1x IA-NT PWR
SetpointsMCB Logic = “CLOSE-ON”
Specification
Automatic remote gen• Three-position ATS• Manual requ• Re
for
7/21/2019 IA NT PWR 2.0 Reference Guide
http://slidepdf.com/reader/full/ia-nt-pwr-20-reference-guide 27/92
InteliATSNT PWR, SW version 2.0, ©ComAp – June 2010 27IA-NT- PWR-2.0-Reference Guide.pdf
AMF + no battery operation
3 x U M
3 x U G
Specification
It is possible to operate controller without a battery supplying the controller. Fofollowing conditions have to be fulfilled:
r such operation the
switched betweening) according to
m for more detailsontacts have to be used for the gen-set start command. Setpoint
locked when GCB is closed, so the powere on the mains bus appears – protection againstvoltage changes arise on Mains.
to Mains when GCB is opened.
/DC power supply source is switched to gen-setsupplying controller disappears
upplied from running gen-set
• d, waits for Gen OK conditionsB closed and the 24V AC/DC power supply source is locked in gen-set
If Mains
• GCB is opened, 24V AC/DC power supply source is unlocked and switched to Mains• MCB is closed• Gen-set is stopped
Hardware requirements1x IA-NT PWR1x 24V/2.5A AC/DC power supply
• Controller is supplied from 24V/2.5A AC/DC power supply whose source isMains and Gen-set via relay (another contacts of the relay for GCB switchthe Mains state (OK/Fault). See the schematic diagra
• Normally closed relay c“GenStart Logic” has to be set to CLOSE-OFF
• Switching of the 24V AC/DC power supply is bsupply is not switched to Mains if voltag
ng” of the power supply when“Flip-floppiIt (power supply) will be switched
Then in the case of Mains failure:
• 24V AC• Voltage• Gen Start relay is deenergized and contacts closed
started• Gen-set is• Controller is s
Controller is initialize• MCB is opened, GC
position.
returns:
7/21/2019 IA NT PWR 2.0 Reference Guide
http://slidepdf.com/reader/full/ia-nt-pwr-20-reference-guide 28/92
InteliATSNT PWR, SW version 2.0, ©ComAp – June 2010 28IA-NT- PWR-2.0-Reference Guide.pdf
Controllers in cascade
G e n S t a r t / S t o p
G e n S t a r t / S t o p
L o a d
G e n r e a d y T o L o a d
G
T o
e n r e a d y
3 x U M
3 x U G
3 x I G
G e n S t a r t / S t o p
G e n r e a d y T o L o a d
Specification
Controllers are suitable for “Cascading” applications allowing load to be split intoThe followi ave to be fulfilled:
more sections.
• Automatic remote gen-set start when the mains fails (AUT mode)• Cascade controlled by Master• Consequent changeover on slave controllers• Simple wiring
Hardw re requirements1 x IA-NT PWR(1 to n) x IA-NT PWR or STD
ng conditions h
a
7/21/2019 IA NT PWR 2.0 Reference Guide
http://slidepdf.com/reader/full/ia-nt-pwr-20-reference-guide 29/92
InteliATSNT PWR, SW version 2.0, ©ComAp – June 2010 29IA-NT- PWR-2.0-Reference Guide.pdf
Cascade, wiring A, Mains Fail timing diagram with configuration description
Cascade, wiring A, Mains Return timing diagram with configuration description
7/21/2019 IA NT PWR 2.0 Reference Guide
http://slidepdf.com/reader/full/ia-nt-pwr-20-reference-guide 30/92
InteliATSNT PWR, SW version 2.0, ©ComAp – June 2010 30IA-NT- PWR-2.0-Reference Guide.pdf
Cascade, wiring B, Mains Fail timing diagram with configuration description
Cascade, wiring B, Mains Return timing diagram with configuration description
7/21/2019 IA NT PWR 2.0 Reference Guide
http://slidepdf.com/reader/full/ia-nt-pwr-20-reference-guide 31/92
InteliATSNT PWR, SW version 2.0, ©ComAp – June 2010 31IA-NT- PWR-2.0-Reference Guide.pdf
d
o install
Getting Starte
How t
GeneralTo ensure proper function:Wiring for binary inputs and analog inputs must not be run with power cables.
en length >3m.
s 36VDC. Maximum allowable power supply voltageNT’s power supply terminals are protected against large pulse power
itions outside its
Binary inputs should use shielded cables, especially wh
Power supplyTo ensure proper function use min. power supply cable of 1.5mm2 Maximum continuous DC power supply voltage iis 39VDC. The InteliATSdisturbances. When there is a potential risk of the controller being subjected to condcapabilities, an outside protection devise should be used.
NOTE: The InteliATSNT controller should be grounded properly in order to protect against lighting strikes!!The maximum allowable current through the controller’s negative terminal is 4A (this is dependent onbinary output load).
For the connection NTs with 12VDC power supply, the InteliATS includes internal capacitors that allowthe controller to continue operation if the battery voltage dip occurs. If the voltage before dip is 10V,after 100ms the voltage recovers to 7 V, the controller continues operating. During this voltage dip thecontroller screen backlight can turn off and on but the controller keeps operating.It is possible to further support the controller by connecting the external capacitor and separatingdiode or I-LBA module:
The capacitor size depends on required time. It shall be approximately thousands of microFarads.The capacitor size should be 5 000 microFarad to withstand 150ms voltage dip under followingconditions:Voltage before dip is 12V, after 150ms the voltage recovers to min. allowed voltage, i.e. 8V
NOTE: Before the battery is discharged the message "Low BackupBatt" appears.
Or by connecting special I-LBA Low Battery Adaptor module:
7/21/2019 IA NT PWR 2.0 Reference Guide
http://slidepdf.com/reader/full/ia-nt-pwr-20-reference-guide 32/92
InteliATSNT PWR, SW version 2.0, ©ComAp – June 2010 32IA-NT- PWR-2.0-Reference Guide.pdf
voltage dip under following conditions:
llowed voltage 5V.
wiring resistance from battery should be up to 0.1 Ohm for I-LBA proper function.
The I-LBA module ensures min. 350msRS232 and other plug-in module is connected.Voltage before dip is 12V and after 350ms the voltage recovers to min. aThe I-LBA enables controller operation from 5VDC (for 10 to 30 sec).The
NOTE: I-LBA may not eliminate voltage drop when used with low temperature (-40°C) version of controllerand display heating element is on (below 5°C). Current drain of heating element exhausts LBAcapacitors very fast
Power supply fusing A one-amp fuse should be connected in-line with the battery positive terminal tmodule
o the controller ands.
Fuse value and type depends on number of connected devices and wire length.type - T1A. Not fast due to internal capacitors charging duringRecommended fuse (not fast)
power up.
Binary output protectionsNOTE: Do not connect binary outputs directly to DC relays without protection diodes, even if they are notconnected directly to controller outputs.
GroundingTo ensure proper function:Use as short as possible cable to the grounding point on the switchboardUse cable min. 2,5mm2 The “-“ terminal of the battery has to be properly grounded
7/21/2019 IA NT PWR 2.0 Reference Guide
http://slidepdf.com/reader/full/ia-nt-pwr-20-reference-guide 33/92
InteliATSNT PWR, SW version 2.0, ©ComAp – June 2010 33IA-NT- PWR-2.0-Reference Guide.pdf
IL-NT BIO8 extension module connection
Current measurement
The number of CT’s is automaticaly selected based on selected value of setpoint ConnectionType[3Ph4Wire / 3Ph3Wire / Split Ph / Mono Ph].
To ensure proper function:Use cables of 2,5mm2
Use transformers to 5AConnect CT according to following drawings:
Three phase application:
It is necessary to ensure that potencial difference between generator current COM terminal andbattery “ -” terminal is maximally ± 2V. Therefore is s trongly recommended to interconnect
these two terminals together.
7/21/2019 IA NT PWR 2.0 Reference Guide
http://slidepdf.com/reader/full/ia-nt-pwr-20-reference-guide 34/92
InteliATSNT PWR, SW version 2.0, ©ComAp – June 2010 34IA-NT- PWR-2.0-Reference Guide.pdf
Connect CT according to following drawings. Terminals L2l and L3l are opened.
Single phase application:
CT location
It is possible to set the location of CT s.
There are two options of CT location.• Load• Gen-Set
According to the connection you have to set the setpoint CT location value to Load or Gen-Set
Voltage measurement and generator connection types
There are 4 voltage measurement ConnectionTypes (setpoint ConnectionType [3Ph4Wire /
3Ph3Wire / Split Ph / Mono Ph] ) options. Every type matches to corresponding generator connectiontype:
1. ConnectionType: 3 Phase 4 Wires
7/21/2019 IA NT PWR 2.0 Reference Guide
http://slidepdf.com/reader/full/ia-nt-pwr-20-reference-guide 35/92
InteliATSNT PWR, SW version 2.0, ©ComAp – June 2010 35IA-NT- PWR-2.0-Reference Guide.pdf
Three phase “wye” measurement – 3PY
3 Phase 4 Wires - STAR Connection
2. ConnectionType: 3 Phase 3 Wires
Three phase “ delta” measurement – 3PD
3 Phase 3 Wires
– DELTA Connection – HI-LEG (wild-leg, red-leg) DELTA Connection
7/21/2019 IA NT PWR 2.0 Reference Guide
http://slidepdf.com/reader/full/ia-nt-pwr-20-reference-guide 36/92
InteliATSNT PWR, SW version 2.0, ©ComAp – June 2010 36IA-NT- PWR-2.0-Reference Guide.pdf
NOTE: Only L1, L2 and L3 wires should be connected. In case of HI-LEG DELTA connection the N (neutral)wire (in the diagram connected between T6 and T9) has to be disconnected.No separation transformers for three wires voltage connection (without N) are needed.
3. ConnectionType: Split Phase
Single-phase measurement – 1PH
Split Phase
– DOUBLE DELTA Connection – ZIG ZAG (DOG LEG) Connection
7/21/2019 IA NT PWR 2.0 Reference Guide
http://slidepdf.com/reader/full/ia-nt-pwr-20-reference-guide 37/92
InteliATSNT PWR, SW version 2.0, ©ComAp – June 2010 37IA-NT- PWR-2.0-Reference Guide.pdf
4. ConnectionType: Mono Phase
Single-phase measurement – 1PH
Mono Phase – MONOPHASE Connection
NOTE: Switchboard lighting strike protection according standard regulation is expected for all 4 connectiontypes!!!
NOTE: Phase sequence check is not possible to evaluate under voltage 50V what causes that if measuredvoltage 50V is within the allowed range, controller will not allow to close the GCB, even if relevant LEDdiod on front panel of IL-NT lits.
7/21/2019 IA NT PWR 2.0 Reference Guide
http://slidepdf.com/reader/full/ia-nt-pwr-20-reference-guide 38/92
InteliATSNT PWR, SW version 2.0, ©ComAp – June 2010 38IA-NT- PWR-2.0-Reference Guide.pdf
Binary inputs
Binary outputs
+
Battery
-
iL
4k7 Ω
+ -
Power Supply
iL
LOAD
+ -
Power Supply
+ -
Battery
RS485 connectionThe line has to be terminated by 120 Ohm resistors at both ends.
in any order, but keepiExternal units can be connected on the RS485 line ng line arrangement (no
star) is necessary.m.
Shielded cable has to be used, shielding has to be connected to PE on one side (controller side).
A) For s ces (all network components within one room) – picture 1interconnect A and B; shielding connect to PE on controller sideB) For longer distances (connection between rooms within one building) – picture 2interconnect A, B, COM; shielding connect to PE in one point
C) In case of surge hazard (connection out of building in case of storm etc.) – picture 3
We recommend to use following protections:
tails, no
Standard maximum link length is 1000
horter distan
7/21/2019 IA NT PWR 2.0 Reference Guide
http://slidepdf.com/reader/full/ia-nt-pwr-20-reference-guide 39/92
InteliATSNT PWR, SW version 2.0, ©ComAp – June 2010 39IA-NT- PWR-2.0-Reference Guide.pdf
ntact.com):2x2-BE (base element)
://www.saltek.cz):
nductors)/CM (1x2+1 conductors)TC/CM (1x2+1 conductors)
Picture 1 - shorter distances (all network components within one room)
Picture 2 - longer distances (connection between rooms within one building)
- Phoenix Contact (http://www.phoenixcoPT 5-HF-5DC-ST with PT
85-TTL)(or MT-RS4- Saltek (httpDM-006/2 R DJ
Recommended data cables: BELDEN (http://www.belden.com) A) For shorter distances: 3105A Paired - EIA Industrial RS-485 PLTC/CM (1x2 coB) For longer distances: 3106A Paired - EIA Industrial RS-485 PLTCC) In case of surge hazard: 3106A Paired - EIA Industrial RS-485 PL
Picture 3 - surge hazard (connection out of building in case of storm etc.)
7/21/2019 IA NT PWR 2.0 Reference Guide
http://slidepdf.com/reader/full/ia-nt-pwr-20-reference-guide 40/92
InteliATSNT PWR, SW version 2.0, ©ComAp – June 2010 40IA-NT- PWR-2.0-Reference Guide.pdf
ts
nputs/Outputs overview table see chapter Technical Data.
Inputs and Outpu
For I NOTE: Any Binary input or output can be configured to any IA-NT controller terminal or changed to differentfunction by LiteEdit software. There is fix 1 sec delay when any binary input is configured asprotection.
Not UsedBinary input has no function. Use this configuration when Binary input is not connected.
AlarmIf the input is closed (or opened) sel d alarm is activated.ecte
Bina nfigu ms
string
ry Alarm co ration ite
Name 14 characters ASCIINC Normally closedContact type
NO ally openedNormWarning Alarm typeTrip All the time Valid if checkbox “Engin
one running
ly” is not checked Alarm active
Engine running only Valid if checkbox “Engine runningonly” is checked
ControlUse this setting to configure the desired function from the list below.
7/21/2019 IA NT PWR 2.0 Reference Guide
http://slidepdf.com/reader/full/ia-nt-pwr-20-reference-guide 41/92
InteliATSNT PWR, SW version 2.0, ©ComAp – June 2010 41IA-NT- PWR-2.0-Reference Guide.pdf
Binary inputs IA-NT - default
BI1 GCB Feedback
Load
k
ansfer
BI6 Remote TEST
BI7 Remote TEST OnLd
BI2 MCB Feedback
BI3 GenReadyTo
BI4 MainsFailBloc
BI5 Remote Tr
Binary inputs – list
Rem Start/StopExternal request for engine run. AUT mode only.
NOTE: If the binary input Rem Start/Stop is active and mains failure occures, the MCB breaker opens andafter the Trans Del delay the GCB breaker is closed. Once the mains is OK, the MainsReturnDel delayelaspes and the GCB breaker is opened. Then after the Trans Del delay is MCB breaker closed. Gen-set remains running as long as Rem Start/Stop is active. See AMF time chart for more details.
without waiting for the AMFtart Del has elapsed. In the case the transfer not succeeded the system will stay in
rms its work normally.
k
t to the output GCB CLOSE/OPEN
back
ergency Stopopened. Input
Access LockIf the input is closed, no setpoints can be adjusted from controller front panel and gen-set mode (OFF-MAN-AUT-TEST) cannot be changed.
Rem TransferExternal request for an immediate transfer from mains to generatorSettings: EmergSneutral position. The MainsFailBlock input perfo
GCB FeedbacUse this input for indication, whether the generator circuit breaker is open or closed.If the feedback is not used, connect this inpu
MCB FeedThis input indicates whether MCB is closed or opened.
EmIf the input is opened, the stop signal for the gen-set is sent and the MCB and GCB areis inverted (normally closed) in default configuration.
NOTE:
Access Lock does not protect setpoints and mode changing from LiteEdit. To avoid unqualifiedchanges the selected setpoints can be password protected. Also the button Fault reset, is not blockedat all and buttons Start and Stop in MAN mode are not blocked.
7/21/2019 IA NT PWR 2.0 Reference Guide
http://slidepdf.com/reader/full/ia-nt-pwr-20-reference-guide 42/92
InteliATSNT PWR, SW version 2.0, ©ComAp – June 2010 42IA-NT- PWR-2.0-Reference Guide.pdf
ode (there are four modes OFF-MAN-AUT-TEST). When opensr is switched back to previous mode.
Remote OFFIf closed, IA-NT is switched to OFF mcontrolle NOTE: This binary input should be connected to schedule timer switch, to avoid start of engine.
te MANd to the controller independently on the position of the MODE
tive, AUTO mode is forced to the controller independently on the position of the MODEst priority.
ST). When opens
Ldrs load
et to MANUAL.ally transferred back to the mains when any gen-set shut down protection activates.
active, setpoints writing or command sending from the external terminal is disabled.
esButton
as the same function as Fault Reset button on the InteliATSNT front panel.
RemoIf the input is active, MAN mode is forceselector.
Remote AUTIf the input is acselector. If another of remote inputs is active, then the REMOTE AUT input has the lowe
Remote TESTIf closed, IA-NT is switched to TEST mode (there are four modes OFF-MAN-AUT-TE
controller is switched back to previous mode.
Rem TEST On Affects the behavior in TEST mode. When input is closed, the controller automatically transfefrom the mains to the gen-set. Setpoint AMF Settings: ReturnFromTEST must be sLoad is automatic
RemControlLockIf the input is
FaultR
Binary input h
GCB Button
Binary input has the same function as GCB button on the InteliATSNT front panel. It is active in MANmode only.
MCB Button
Binary input has the same function as MCB button on the InteliATSNT front panel. It is active in MANmode only.
MainsFailBlockIf the input is closed, the automatic start of the gen-set at Mains failure is blocked. In case of runnin
gen-set the GCB is opened, gen-set goes to Cooling p
g
rocedure and stops.
ns for successful gen-set start andreadiness to undertake load can be – depending on the GenerProtect setpoint – evaluated from thevoltage and the frequency of the generator or from the state of GenReadyToLoad input. Theconditions have to be fulfilled during time defined by the MaxGenStartDel setpoint (which can be evenunlimited). More info can be found in tp t description.
Neutral PosIn MAN mode this input switches a three position ATS switch to its neutral position – it activates thebinary output NeutralPosition and switches the MCB and GCB off.
GenReadyToLoadIndicates wether the gen-set is ready to undertake load. Conditio
the se oin
7/21/2019 IA NT PWR 2.0 Reference Guide
http://slidepdf.com/reader/full/ia-nt-pwr-20-reference-guide 43/92
InteliATSNT PWR, SW version 2.0, ©ComAp – June 2010 43IA-NT- PWR-2.0-Reference Guide.pdf
ot have usuallypower sources.Then this
s is healthy to be able to respond to Mains failure.
has been added.tive. If the reason
ed, the alarm is activated. If not, the alarm does notperform “filtering” of alarms within a specified period of time.
llowing setpoints:
MainsHealthyThis iinput was creted mainly for cascading applications, where slave controllers do nMains and Gen-set voltage measuring inputs connected to the repspectivebinary input tells the controller if Main
Programmable delay on alarmsPossibility to set programmable delay on alarms configured for binary intput 6 and 7If set, it blocks alarms of the respective binary input for the whole time the delay is acfor the alarm persists after the delay time expir appear. This feature allows the user toThe delay length can be set via the fo
Binary outputs IA-NT - default
BO1 GenStart/Stop
pen
e/Open
AMF
ail
rt Fail
uts - list
BO2 Alarm
BO3 GCB Close/O
BO4 MCB Clos
BO5 Ready To
BO6 AL Mains F
BO7 AL Sta
Binary outp
Not UsedOutput has no function.
cked when theoutput is inactive and the GCB is blocked too. Output can be inverted (CLOSE-OFF) using Basic
nStart Logic setpoint.
tput closes when the gen-set start is requested and opens after the AMF Sett ings : Prestart
d. Afterwards the GenStart/Stop output is activated as a start signal for the remote
I the Mains Fail had occurred and the gen-set start is theresult of this event. See the AMF Sett ings : Prestart Time setpoint for more info.
AlarmThe output closes if :
• any alarm comes up orThe output opens if
• FAULT RESET is pressed
GenStart/StopThe closed relay sends remote start signal to the gen-set. Generator protections are blo
Settings: Ge
PrestartThe ou
Time has elapsegen- t.se
Pre atr nsfers activated during the Prestart phase when
The output closes again if a new fault comes up.
7/21/2019 IA NT PWR 2.0 Reference Guide
http://slidepdf.com/reader/full/ia-nt-pwr-20-reference-guide 44/92
InteliATSNT PWR, SW version 2.0, ©ComAp – June 2010 44IA-NT- PWR-2.0-Reference Guide.pdf
The output controls the generator circuit breaker.
GCB Close/Open
NOTE: Supposed time to close (reaction time) of GCB is 0.1 sec.
ates Generator Circuit Breaker coil.
oil
Breaker coil after voltage drop-out.
/Openaker.
tivates Mains Circuit Breaker coil.
eactivates Mains Circuit Breaker coil.
ntrols Mains Circuit Breaker coil after voltage drop-out.
copy of Fault Reset button on controller and binary input FaultResButton.
opy of generator status LED on IA-NT front panel. The output is closed if gen-set is
On Loadms OK and (LBI) GCB Feedback OK
R ave, if the controller is able to start the engine and simultaneously the controller is in
sed if following conditions are fulfilled:
OFF Mode
Ready To LoadThe output is closed if gen-set is running and all electric values are in limits and no alarm is active - itis possible to close GCB or it is already closed. The output opens during cooling state.
Mains Healthy
The output is copy of mains status LED on IA-NT front panel. The output is closed if mains voltageand frequency are within limits.
GCB ON CoilThe output activ
GCB OFF CThe output deactivates Generator Circuit Breaker coil.
GCB UV CoilThe output controls Generator Circuit
MCB CloseThe output controls the mains circuit bre
MCB ON CoilThe output ac
MCB OFF CoilThe output d
MCB UV CoilThe output co
Fault Reset
The output is a
Gen HealthyThe output is a crunning and all gen-set electric values are in limits.
Gen(LBO) Gener On Load <= (LBO) Gen Para
e dy To AMFThe output is acti AUT Mode.
ReadyThe output is clo
• Gen-set is not running and• Controller is not in
7/21/2019 IA NT PWR 2.0 Reference Guide
http://slidepdf.com/reader/full/ia-nt-pwr-20-reference-guide 45/92
InteliATSNT PWR, SW version 2.0, ©ComAp – June 2010 45IA-NT- PWR-2.0-Reference Guide.pdf
On Load <= (LBO) Mains Healthy and (LBI) MCB Feedback OK
r overvoltage shutdown alarm activates.
The out • alarm is not active and• FAULT RESET is pressed
Mains On Load(LBO) Mains
AL Gen >VThe out tpu closes if the generato
put opens, if
AL Gen <VThe out ervoltage shutdown alarm activates.The output opens, if
alarm is not active and
put closes if the generator und
• • FAULT RESET is pressed
AL Gen VoltsThe output closes if the generator over/under voltage alarm or voltage asymmetry alarm activates.
ns, if
FAULT RESET is pressed
The output ope• alarm is not active and•
AL Ge the generator over/under frequency alarm activates.
alarm is not active andpressed
n FreqOutput closes if The output opens, if
• • FAULT RESET is
AL Gen >Freqtivates.
e andssed
Output closes if the generator over frequency alarm ac
s, ifThe output open• alarm is not activ• FAULT RESET is pre
AL Gen <Freq
• alarm is not active andRESET is pressed
Output closes if The out t
the generator under frequency alarm activates.pu opens, if
• FAULT
AL Mains Vol tsThe output r/under voltage alarm or voltage asymmetry alarm activates.
if
Output clos ncy alarm activates.The output opens, if
• alarm is ot active
AL Over load SdOutput closes if the generator overload alarm activates.The output opens, if
• alarm is not active and• FAULT RESET is pressed
closes if the mains oveThe output opens,
• alarm is not active
AL Mains Freqes if the mains over/under freque
n
7/21/2019 IA NT PWR 2.0 Reference Guide
http://slidepdf.com/reader/full/ia-nt-pwr-20-reference-guide 46/92
InteliATSNT PWR, SW version 2.0, ©ComAp – June 2010 46IA-NT- PWR-2.0-Reference Guide.pdf
ltage or oil pressureprotection goes active 60s after stop command. With start goes this protection
The out alarm is not active and
FAULT RESET is pressed
AL Stop FailOutput closes when the engine have to be stopped, but speed or frequency or vois detected. Thisinactive.
put opens, if•
•
AL Mains FailOutput c slo es if the mains ov
rm activates.er/under voltage alarm, voltage asymmetry alarm or mains over/under
frequency alaens, if
AL St tOutput close
, if
ctive andis pressed
The output op• alarm is not active
ar Fails after the gen-set start-up fails.
The output opens• alarm is not a AULT RESET• F
AL OvercurrentOutput closes if the generator
current unbalance orrm activates.
IDMT over current or
short current alaThe output opens, if Alarm is not active andFAULT RESET is pressed
AL Ba IA-NT performs reset during start procedure (probably due to weak battery) or
rs.s, if
essed
tteryFailOutput closes whenwhen battery under/over voltage warning appeaThe output open
• alarm is not active and• FAULT RESET is pr
AL Common WrnOutput closes when any warning alarm appears.The out t
active and• FAULT RESET is pressed
pu opens, if• No warning alarm is
AL Common TripOutput closes when any trip alarm appears.
• No trip alarm is active and• FAULT RESET is pressed
The output opens, if
Mode OFFThe output is closed, if OFF Mode is selected.
Mode MANThe output is closed, if MAN Mode is selected.
7/21/2019 IA NT PWR 2.0 Reference Guide
http://slidepdf.com/reader/full/ia-nt-pwr-20-reference-guide 47/92
InteliATSNT PWR, SW version 2.0, ©ComAp – June 2010 47IA-NT- PWR-2.0-Reference Guide.pdf
closed, if AUT Mode is selected.
selected.
tive andis pressed
Mode AUTThe output is
Mode TESTThe output is closed, if TEST mode is
The output opens, if Alarm is not acFAULT RESET
Exerc Timer 1in AUT mode.
neously, gen-set is started when it is in AUT mode.
T
MCB and GCB Close/Openlevel change
TS three way switch to the position II.l Pos output switches the ATS three way switch to the position 0 (middle).behavior of the ATS output differs depending on the priority of the inputs of the particular
overrides the current position of thewitc
Neutral Coil
B ON
Neutral Coil output switches the ATS three way switch to the position 0 (middle).
Power SwitchThis switch is assigned to the gen-set active power. The setpoints PowerSwitch ON [kW]
Output activates when Timer 1 is active. Simultaneously, gen-set is started when it is
Exerc Timer 2Output activates when Timer 2 is active. Simulta
Not In AUOutput activates when the controller is not in AUT mode.
Neutral PosSwitches ATS switch to its neutral position. It is a complement to thebinary outputs and it switches the ATS switch to its neutral position by applying voltage(log. 0/ log. 1). MCB Close/Open output switches the ATS three way switch to the position I. GCB Close/Open output switches the A Neutra
The resultingtype of the ATS switch.If the neutral position input of the switch has the highest priority its h and forces the switch to the neutral position.
Activates the neutral position coil of the ATS switch. It is a complement to the MCB and GCCoil and it switches the ATS switch to its neutral position by applying a voltage pulse. MCB ON Coil output switches the ATS three way switch to the position I. GCB ON Coil output switches the ATS three way switch to the position II.
andPowerSwitch OFF [kW] for on and off level adjustment are located in the setpoint group EngineParams. Typical usage for this binary output can be switching of dummy load. The output behaves
7/21/2019 IA NT PWR 2.0 Reference Guide
http://slidepdf.com/reader/full/ia-nt-pwr-20-reference-guide 48/92
InteliATSNT PWR, SW version 2.0, ©ComAp – June 2010 48IA-NT- PWR-2.0-Reference Guide.pdf
based on the setpoint adjustment as described on picture lower:
Shunt Trip Activates when the system is running in short time parallel with mains (closed transition) and the timeof the parallel run is longer than 300ms. It is a kind of protection against long time parallel run withmains when closed transition takes place.
7/21/2019 IA NT PWR 2.0 Reference Guide
http://slidepdf.com/reader/full/ia-nt-pwr-20-reference-guide 49/92
InteliATSNT PWR, SW version 2.0, ©ComAp – June 2010 49IA-NT- PWR-2.0-Reference Guide.pdf
sSetpoint
Password
EnterPasswordPassword is a four-digit number. Password enables change of relevant protected setpoints.
key to enter the password.Use ↑ or ↓ keys to set and ENTER NOTE: There is only 1 level of a password.
ChangePassword
Use ↑ or ↓ keys to set and ENTER key to change the password.
NOTE:
At first the password has to be entered before the new password can be changed.
Basic Settings
ControllerNameefine e, usedUser d d nam for InteliNT identification at remote phone or mobile connection.llerN 14 characters long and have to be entered using LiteEdit software.
[kW]
rrent [ A ]rrent and short current protection and means maximal
er Protect: Amps IDMT Del, Short Crct Sd setpoints.fferent from generator rated current value.
Step: 1 Ange: 1 - 10000 A
Contro ame is max
Nominal Power Nominal power of the generatorStep: 1kW
– 5000 kWRange: 1
Nomin CuIt is current limit for generator IDMT over cucon n genti uous erator current. See GenNominal Current can be di
Ra
CT Ratio [/5A]Gen-set phases current transformers ratio.Step: 1 A
Range: 1 – 5000 A / 5A
Hint:For firmware versions < 2.0:For CT Ratio <= 250 the values of power and current are displayed in a controller with one decimal.For CT Ratio > 250 the values of power and current are displayed in a controller with integralnumbers. If you change CT Ratio in LiteEdit or directly in the controller, decimal numbers will not bechanged immediately. The change w e uted only by reconfiguring in LiteEdit. The statistics ofill be xecpower will be recounted at this time wi cimal numbers of power.th regards to deWARNIN When you change the firmware, statistics can be invalid!G!WARNING! Change of CT ratio over value 250 without reconfiguring in LiteEdit can causeoverflow of current measurement and improper funct ion of controller!
7/21/2019 IA NT PWR 2.0 Reference Guide
http://slidepdf.com/reader/full/ia-nt-pwr-20-reference-guide 50/92
InteliATSNT PWR, SW version 2.0, ©ComAp – June 2010 50IA-NT- PWR-2.0-Reference Guide.pdf
For firmware version >= 2.0:Decimal switching is not done via value of “CT ratio” setpoint, but in configuration window of LiteEditsoftware via icon „Units/Formats“:
PT Ratio [/1]rmers ratio.
V / V
[/1]Mains potential transformers ratio.Step: 0,1 V / VRange: 0,1 – 500,0 V / V
NomVolts Ph-N [V]
Nominal generator voltage (phase to neutral)Step: 1VRange: 80 – 20000 V
Gen-set potential transfoStep: 0,1Range: 0,1 – 500,0 V / V
Vm PT Ratio
7/21/2019 IA NT PWR 2.0 Reference Guide
http://slidepdf.com/reader/full/ia-nt-pwr-20-reference-guide 51/92
InteliATSNT PWR, SW version 2.0, ©ComAp – June 2010 51IA-NT- PWR-2.0-Reference Guide.pdf
NOTE: Phase sequence check is not possible to evaluate under voltage 50V what causes that if measuredvoltage 50V is within the allowed range, controller will not allow to close the GCB, even if relevant LEDdiod on front panel o NTf IA- lits.
al ge e (phase to phase)1V
[Hz]e sually 5
Ac tiv ityAtOFF [ENABLE/DISABLE]trolle avior of OFF mode.
ts and there is Fault reset active all thetime.
, AUT,TEST]
de c es by MODE→ or ←MODE buttons.
NomV ts Phol -Ph [V]Nomin nerator voltagStep:Range: 000138 – 35 V
Nominal FreqNominal generator frequ ncy (u 0 or 60 Hz )Step: 1HzRange: 45 – 65 Hz
ENABLE: Con r at OFF mode stays at standard beh
DISABLE: Controller at OFF mode opens all binary outpu
ControllerMode [OFF, MAN
Equivalent to Controller mo hang NOTE: Controller Mode change can be separately password protected.
dress different from the default valuere controllers can be intercon ssed e.g. from Modbus
ControllerAddr (1 .. 32) [-]Controller identification number. It is possible to set controller ad(1) so that mo nected (via RS485) and acce
terminal.
NOTE: When ope ing connection to the controller it's addr n e setting in PC tool.ess has to correspond with thFrom LiteEdit it is only possible to connect to controllers with address 1.
COM1 Mode [DIRECT/MODEM/MODBUS]Communication protocol switch for the COM1 channel.DIRECT: nication protocol via direcMODEM: nication protocol via mod
LiteEdit commu t cable.
uide.LiteEdit commu em.
US: tion in InteliCommunication gMODB Modbus protocol. See detailed descrip
NOTE: For details on communic. speed and other technical parameters please see chapter Technical Data.For detail description see chapter Modbus protocol. Register oriented modbus is supported.
COM2 Mode [DIRECT/MODBUS]Communication protocol switch for the COM2 channel, if dual communication module is pluged in.DIRECT: LiteEdit communication protocol via direct cable.MODBUS: Modbus protocol. See detailed description in InteliCommunication guide.
NOTE: For details on communic. speed and other technical parameters please see chapter Technical Data.For detail description see chapter Modbus protocol. Register oriented modbus is supported.
7/21/2019 IA NT PWR 2.0 Reference Guide
http://slidepdf.com/reader/full/ia-nt-pwr-20-reference-guide 52/92
InteliATSNT PWR, SW version 2.0, ©ComAp – June 2010 52IA-NT- PWR-2.0-Reference Guide.pdf
s selected on COM1 or COM2 channels, the Modbus communication speed inhere
-OFF]
i ld start when the output Gen Start/Stop is closed.ld start when the output Gen Start/Stop is opened.
ndWarning threshold for low battery voltage.
0,1 VVolts)
Ove [V]hold or hi b ttery voltage.
Connection h3Wire / Split Ph / Mono Ph]w
l - 4 wires,t – 3PY, 3x CT
3Ph3Wire: DELTA Connection, 3 Phase without neutral - 3 Wires,
Thr ent – 3PD, 3x CT
MONOPHAS
rrent measurement) is located next to the load.t: rement) is located next to the gen-set.
/INPH-OPEN/CLOS-OPEN]lly enhances controller function and brings
p hase Transition and Closed Transition (short time parallel). Controllerprovide urces dependingoOICLOSED Closed Transition INPH-OPEN Open In-phase Transition or Open Delayed Transition CLOS-OPEN Closed Transition or Open Delayed Transition
1. Open Delayed Transition
Open Delayed Transition is standard type of changeover provided by most common AMF or ATScontrollers supplied by other vendors. Controllers perform load transfer between both powersources with break (blackout). Delayed Transition means there is delay between source breaker
opening and target breaker closing.
ModbusComSpeed [9600,19200, 38400, 57600]If the Modbus mode ibps can be adjusted .
GenStart Logic [CLOSE-ON/CLOSE
The set po nt influences the behavior of the output Gen Start/Stop.CLOSE-ON: Gen-set shouCLOSE-OFF: Gen-set shou
Batt U ervolt [V]
Step:Range: 8V – 40 (Battery >
Batt rvoltWarning thres f aStep: 0,1 V
: 8V – 40 (Battery <Volts)Range
Batt Volt Del [s]Delay for low battery voltage alarm.Step: 1sRange: 0 – 600 s
Type [3Ph4Wire / 3PGenerator inding connection.
nnection, 3 phases and neutra3Ph4Wire: STAR CoThree phase “wye” measuremen
ee phase “delta” measuremSplit Phase: DOUBLE DELTA Connection, Split Phase,Single-phase measurement – 1PH, 1xCT
Mono Phase: E,Single-phase measurement – 1PH, 1x CT
CT Location [Load / GenSet]Load: CT (cuGenSe CT (current measu
Transition [OPEN/INPHASE/CLOSED Ability to perform passive synchronization dramatica
ossibility to provide Open In-ps below described types of changeover between Mains and Gen-set power son following setpoint value:PEN Open Delayed Transition
N-PHASE Open In-phase Transition
7/21/2019 IA NT PWR 2.0 Reference Guide
http://slidepdf.com/reader/full/ia-nt-pwr-20-reference-guide 53/92
InteliATSNT PWR, SW version 2.0, ©ComAp – June 2010 53IA-NT- PWR-2.0-Reference Guide.pdf
tion ATS switch or two independent breakers/contactors can be used as
A-NT controllers. Ourcontrollers offer possibility to setup load transfer delay via Transfer Del setpoint.
Two or three posiswitching mechanism.
Bellow you can see how is Open Delay Transition implemented by I
HINT:This transition can perform fastest possible changeover if Transfer Del is set to zero value.Overall blackout time then equals to 20 ms + breaker reaction time.
HINT: Use longer delay time to avoid problems with motor starters. (Motor starts prefer to see break of afew seconds so they can initialize properly).
HINT: To avoid issues with contactor mechanical interlocks use delay 0.75s or longer (mech. interlock oncontactors takes some time to clear). If you try to close one contactor before interlock has clearedit can jam and you end up with out supply to load).
7/21/2019 IA NT PWR 2.0 Reference Guide
http://slidepdf.com/reader/full/ia-nt-pwr-20-reference-guide 54/92
InteliATSNT PWR, SW version 2.0, ©ComAp – June 2010 54IA-NT- PWR-2.0-Reference Guide.pdf
here delay duringn both power
setpoint value is ignored (equals to zero). See description of
for such systems where fast changeover (very short blackout) isot possible to use
nt breakers/contactors can be used asays) affects
switching time << 200 ms). Thefaster the better to ensure real in-phase transition –> once sync moment is calculated and sourceis disconnected from load, electrical parameters of load are changing dynamically and could fallout of sync rapidly. Real phase difference depends on that switching time.
2. Open In-phase Transition
Open In-phase Transition represents special kind of Open Delayed Transition wchangeover is reduced to minimal possible value and transition initiates only whesources are in sync. Transfer Delpassive synchronization for more info.
This kind of transition is suitablerequired, huge inductive load (e.g. large electric motor) is involved and it is nClosed Transition due to some reason.
Two or three position ATS switch or two independeswitching element. Reaction time of whole switching mechanism (including control reloverall changeover time and in-phase transfer accuracy.
It is recommended to use as fast switches as possible (overall
Picture above shows how is Open In-phase Transition implemented by IA-NT controllers.
In case of system using two separate breakers/contactors controller ensures no overlap betweenboth switches during changeover however mechanical interlock can still be useful.Two or three position ATS switches ensure this by its nature.
HINT:
7/21/2019 IA NT PWR 2.0 Reference Guide
http://slidepdf.com/reader/full/ia-nt-pwr-20-reference-guide 55/92
InteliATSNT PWR, SW version 2.0, ©ComAp – June 2010 55IA-NT- PWR-2.0-Reference Guide.pdf
It is necessary to use fast breakers with known closing/opening time when Open In-phaseTransition takes place. Breaker switching time is used as parameter (MCB Delay, GCB Delay) forcalculation/prediction of exact in-sync moment.Overall blackout time equals to 100 ms + one breaker reaction time (incl. control relay delay).
HINT:
In case of source (e.g. mains) failure changeover from source is always performed as opendelayed, not as in-phase.
HINT:During system tests two separate breakers/contactors with switching time below 50ms were usedalong with fast ATS switches (e.g. SOCOMEC ATyS M 3s, switching time 180 ms). We do not recommend usage of switching elements their reaction time exceeds these values!
HINT:Breaker delay default value for both breakers (MCB Delay, GCB Delay) is set to 50ms. ATS switchdelay consists of both delays.
3. Closed Transition
Closed Transition presents transition type where both breakers/contactors overlap for 100 ms andis suitable for
e
on time of wholeswitching mechanism (including control relays) affects overall changeover time.
It is required to use as fast switches as possible (breaker opening time < 100 ms including controlrelay). If parallel run exceeds 200 ms both breakers are opened and alarm is activated. If parallelrun still continues (breakers are closed for at least 100 additional milliseconds), binary output
Shunt Trip is activated (if configured).
transition initiates only when both power sources are in sync. This kind of transitionsuch systems where no break (no blackout) changeover is required. Transfer Del setpoint valuis ignored (equals to zero).
See description of passive synchronization for more info.
Two independent breakers/contactors are required as switching elements. Reacti
7/21/2019 IA NT PWR 2.0 Reference Guide
http://slidepdf.com/reader/full/ia-nt-pwr-20-reference-guide 56/92
InteliATSNT PWR, SW version 2.0, ©ComAp – June 2010 56IA-NT- PWR-2.0-Reference Guide.pdf
HINT:It is necessary to use fast breakers with known closing/opening time when Closed Transition takesplace. Breaker switching time is used as parameter (MCB Delay / GCB Delay) forcalculation/prediction of exact in-sync moment.
HINT:In case of source (e.g. mains) failure changeover from source is always performed as opendelayed, not as closed.
HINT:During system tests two separate breakers/contactors with switching time below 50ms were used.We do not recommend usage of switching elements their reaction time exceeds these values.
HINT:Breaker delay default value for both breakers (MCB Delay, GCB Delay) is set to 50ms.
ition, Closed + Open Delayed Transitionequals to [INPH-OPEN] or [CLOS-OPEN], system continues with Open
elaye sition after requested synchronized transition failed (sync timeout expired soonerthan both sources reached synchronized state)
GCB Delay [s]By means of this setpoi system gets m n about breaker/contactor switching time. This valueis needed for exact sync oment/ time predi n.Step: 0.01 sRange: 0.01 – 60.00 sDefault: 0.05 s
4. Closed + Open Delayed TransIf Setpoint TransitionD d Tran
nt infor atio m ctio
7/21/2019 IA NT PWR 2.0 Reference Guide
http://slidepdf.com/reader/full/ia-nt-pwr-20-reference-guide 57/92
InteliATSNT PWR, SW version 2.0, ©ComAp – June 2010 57IA-NT- PWR-2.0-Reference Guide.pdf
rmation about breaker/contactor switching time. This valued f oment/ time prediction.
Range: 0.01 – 60.00 s
MCB Delay [s]By means of this setpoint system gets infois nee or exact sync m
.01 sde
Step: 0
Default: 0.05 s
HINT:Value of breaker switching time MUST contain all the parts of breaker delay (i.e. breaker switchingtime plus switching time of relay used for breaker control).The more exact value is given, the more exact is the sync result.
Engine Params
Pres Titart me [s]s Prestart and/or Pretransfer output prior to the engine start.
u w nt to ave utput Prestart/Pretransfer open.
[s]
el [s]u START/STOP. When generator does not reach
defined limits Basic Settings: Nominal Freq) within Max Start Del, Trp Start Fail alarm occurs and thegen-set will shut down. See the table below for a description of the engine start evaluation.If MaxStartDel is longer then 600 s it means there is NO TIMEOUT.Step: 1sRange: 0 – 600 s, 601 s = NO TIMEOUT
Time of clo ing of theSet to zero if yo a le the oStep: 1s
: 0 – 600 sRange
Cooling TimeRuntime of the lo gun aded en-set to cool the engine before stop.Step: 1sRange: 0 – 3600 s
Max Start DThis timeo t starts after closing binary output GEN
7/21/2019 IA NT PWR 2.0 Reference Guide
http://slidepdf.com/reader/full/ia-nt-pwr-20-reference-guide 58/92
InteliATSNT PWR, SW version 2.0, ©ComAp – June 2010 58IA-NT- PWR-2.0-Reference Guide.pdf
Engine start evaluation diagram:
Min Stab Time [s]Minimum time interval between defined generator voltage is reached to GCB is clIf BI: GenReadyToLoad is not configured, timer is not used.Step: 1s
ge: 1 – 300 s
osed.
Stop Timeof the Stop Time setpoint tells the controller how long should it wait for the
orpires the Wrn Stops Stop command to
(Start/Stop output is deactivated).Step: 1sRange: 0 – 3601 sec Value 3601 mean ntroller doesn’t care for the engine is
stopped (Wrn ounced).
Power switch functionThis switch is assigned to the gen-set active power. Typical usage for this binary output can be
switching of dummy load. The output behaves based on the setpoint adjustment as described onpicture lower:
Ran
[s]Period given by the valueengine to change to the stop state (stop state means GenReadyToLoad signal is deactivatedgenerator voltages disappeared). If the engine is still running after the stop time exFail alarm is announced. Stop Fail starts counting always when the controller sendthe engine
s the co Stop Fail is never ann
7/21/2019 IA NT PWR 2.0 Reference Guide
http://slidepdf.com/reader/full/ia-nt-pwr-20-reference-guide 59/92
InteliATSNT PWR, SW version 2.0, ©ComAp – June 2010 59IA-NT- PWR-2.0-Reference Guide.pdf
PowerSwitch ON [kW]witch” on.
1: 0 kW
PowerSwitchOFF [kW]Threshold level for switching the binary output “Power Switch” off.Step: 1Range: 0 – 32000 kW
Threshold level for switching the binary output “Power SStep:Range 0 – 3200
7/21/2019 IA NT PWR 2.0 Reference Guide
http://slidepdf.com/reader/full/ia-nt-pwr-20-reference-guide 60/92
InteliATSNT PWR, SW version 2.0, ©ComAp – June 2010 60IA-NT- PWR-2.0-Reference Guide.pdf
Gener Protect
NOTE: All electric protections when activated result in shutdown.
Gener otect [ENABLE/DIPr SABLE]Generato ntroller are active.
are inactive.
loa [%]erload ower)
1% of Nominal power
loa [s]o d ala
r [%]o nt reaches Short Crct Sd limit.
nt :
[s]
10.00 s
IDMT curve shape rotection for 200%overcurrent IStep:
ry inverse” generator over current protection. Reaction time is not constant but depends on
mal value of all measured phases of generator current.
ENABLE: r protections of the coDISABLE: en r ctionsG erato prote of the controller
Over dThreshold for generator ov (in % of Nominal pStep:Range: 0 – 200%
Over d DelDelay for generat r overloa rm.Step: 0.1sRange: 0 – 600.0 s
Short Crct T pr curreShutdown occurs when generat
% of Nominal curreStep: 1Range 100 - 500 %
Short Crct DelDelay for generator shorcurrent alarm.
1sStep: 0.0:Range 0.00 –
Amps IDMT Del [s ]selection. Amps IDMT Del is Reaction time of IDMT p
Current.gen = 2* Nomin0.1 s0.1 - 60.0 sRange:
IDMT is “vegenerator over current level according following formula.
Igen is maxi
Amps IDMT Del * Nomin Current Reaction time =
Igen - Nomin Current
NOTE: Reaction time is limited up to 900 sec = 15 minutes. IDMT protection is not active for Reaction timevalues longer than 15 minutes.
EXAMPLE of Reaction time for different over current levels. Values in column 200% are IDMT CurrDel.
7/21/2019 IA NT PWR 2.0 Reference Guide
http://slidepdf.com/reader/full/ia-nt-pwr-20-reference-guide 61/92
InteliATSNT PWR, SW version 2.0, ©ComAp – June 2010 61IA-NT- PWR-2.0-Reference Guide.pdf
Igen
Nominal Current Short Crct Sd
Amps IDMT Del
Maximal Reaction time
R e a c t i o n t i m e
Amps Unbal Trp [%] old for generator current asymmetry (unbalance).
Step: 1% of Nominal current1 – 200% of Nominal current
s U [s]lance
0.1 s
]Threshold for generator overvoltage. All three phases are checked. Maximum out of three is used.Step: 1% of Nominal voltageRange: 0(Gen <V Sd) – 200%
Gen <V Trp [%]Threshold for generator undervoltage. All three phases are checked. Minimum out of three is used.
Step: 1% of Nominal voltageRange: 0% – 200 (Gen >V Sd)%
rrentOvercu % =
MT CDel
≤ 100 % 101 % 110 %200ID urr
0,2 s o ac 20 2 sN tion s
Thresh
Range:
Amp nbal DelDelay for generator current unba
Step:Range: 0.0 – 600.0 s
Gen >V Trp [%
2 s No 200 s 20 sactionReaction t ime
20 s No action No action(time > 900 s)
200 s
7/21/2019 IA NT PWR 2.0 Reference Guide
http://slidepdf.com/reader/full/ia-nt-pwr-20-reference-guide 62/92
InteliATSNT PWR, SW version 2.0, ©ComAp – June 2010 62IA-NT- PWR-2.0-Reference Guide.pdf
ervoltage and overvoltage alarm
]hold f ance alarm.
al voltage200% f No l voltage
[s]unbala arm.
>Fr n ator p ase L rfrequency.
% of Nominal frequency
[%]
: 0 (Gen >Freq Sd ) % of Nominal frequency
[s]
ble del y on alarmsle configured for binary intput 6 and 7 has been added.spective binary input for the whole time the delay is active. If the reason
the delay time expired, the alarm is activated. If not, the alarm does notlows the user to perform “filtering” of alarms within a specified period of time.
l gth can be set via the following setpoints:
[s]input nr. 6
ctStep: 0.1s
Range: 0 – 360.0 s
AMF Set tings
Gen V Del [s]Delay for generator undStep: 0.1sRange: 0.0 – 600.0 s
Volt Unbal Trp [%Thres or generator voltage unbalStep: 1% of NominRange: 0 – o mina
Volt Unbal DelDelay for generator voltage nce alStep: 0.1sRange: 0.0 – 600.0 s
Gen eq Trp [%]Threshold for ge er h 3 ove
Step: 0.1% of Nominal frequency: 200.0Range 0 (Gen <Freq Sd) –
Gen <Freq TrpThreshold for generator phase L3 underfrequency.
0.1% of Nominal frequencyStep:Range 0.0 – 20
Gen Freq DelDelay for generator underfrequency and overfrequency alarm.Step: 0.1sRange: 0.0 – 600.0 s
Programma adelay on alarmsPossibility to set programmab
the reIf set, it blocks alarms of sists afterfor the alarm per
appear. This feature alThe delay en
BI6 DelayDelay for alarm on binarySetpoint group: Gener Prote
Range: 0 – 360.0 s
BI7 Delay [s]Delay for alarm on bin inp r. 7ary ut nSetpoint group: Gener ProtectStep: 0.1s
RetFromIsland [MANUAL, AUTO]MANUAL: After closing GCB, IA-NT goes to MAN Mode automatically.
AUTO: No automatic switching to MAN Mode.
7/21/2019 IA NT PWR 2.0 Reference Guide
http://slidepdf.com/reader/full/ia-nt-pwr-20-reference-guide 63/92
InteliATSNT PWR, SW version 2.0, ©ComAp – June 2010 63IA-NT- PWR-2.0-Reference Guide.pdf
failure to the start of the gen-set
6000
]return to the GCB opening.
1s
ng to MCB closing during the return procedure.Delay after MCB opening to GCB closing if the setpoint MCB Opens On set to GENRUNStep: 0.1sRange: 0 – 600.0 s
EmergStart Del [s]Delay after the mainsStep: 1sRange: 0 – s
MainsReturnDel [sDelay after the mainsStep:Range: s1 – 3600
Trans Delfer [s]Delay after GCB openi
7/21/2019 IA NT PWR 2.0 Reference Guide
http://slidepdf.com/reader/full/ia-nt-pwr-20-reference-guide 64/92
InteliATSNT PWR, SW version 2.0, ©ComAp – June 2010 64IA-NT- PWR-2.0-Reference Guide.pdf
The time charts bellow show recommended setting of AMF Sett ings : Transfer Del setpoint.
shor eedback of t B Close/Open s G sfer Del
Close/Open output straight away (100 ms) must be set to sum of “MCB opening” + “del”
after the MCB feedback input deactivates. time.
o e D l [s]-up procedure)
p
[%]hree is used.
tageRange: 50 (Mains <V) – 150%
[%]hold for mains undervoltage. All three phases are checked. Maximum out of three is used.
nominal voltage0 – 15 (Mai )%
[s]rvoltage and overvoltage
s
V l [%]e unbal
1% of Nominal voltage
V [s]Delay for mains voltage nbalanceStep: 0.1 sRange: 0- 60.0
Mains >Freq [%]
Threshold for mains overfrequency. All three phases are checked. Maximum out of three is used.Step: 0.1% of Nominal frequencyRange: 50 (Mains <Freq) – 150.0%
If the Transfer Del setpoint is set ter If some delay between MCB f than the time required for opening he deactivation and closing of GC
output is required, then the Trancircuit breaker, the controller close CB
MCBClose/Open
MCBFeedback
GCB
MCBClose/Open
MCBFeedback
GCBClose/Open
MCB opening del
Transfer Del
MCB Cl s eDelay after mains returns to MCB closing, if gen-set is not running(e.g. is in startSte : 0.1sRange: 0 – 60.0 s
Mains >VThr s r mains overvoltagee hold fo . All three phases are checked. Maximum out of t
Step: 1% of Nominal vol
Mains <VThresStep: 1% ofRange: 5 % 0 ns >V
Mains DelVDelay for mains undeStep: 0.1Range: 0 – s600.0
Mains UnbaThreshold for mains voltag anceStep:Range: 1 – 150%
Mains Unb Delu
Close/Open
TransferDel
MCB opening
7/21/2019 IA NT PWR 2.0 Reference Guide
http://slidepdf.com/reader/full/ia-nt-pwr-20-reference-guide 65/92
InteliATSNT PWR, SW version 2.0, ©ComAp – June 2010 65IA-NT- PWR-2.0-Reference Guide.pdf
hold f All three phases are checked. Maximum out of three is used.ency
0 – 15 .0(Ma req)%
rfrequency and overfrequency0.1s0 60.0
]The set point influences the behavior of the output MCB CLOSE/OPENCLOSE-ON: When the output MCB CLOSE/OPEN is closed – MCB should be closed.CLOSE-OF the output MCB CLOSE/OPEN is closed – MCB should be opened.
Mains <Freq [%]Thr s or mains underfrequencye .Step: 0.1% of Nominal frequRange: 5 % 0 ins >F
Mains Freq Del [s]Delay for mains undeStep:Range: – s
MCB Logic [CLOSE-ON / CLOSE-OFF
F: When
IA “ OFF”
MCB logic = ”CLOSE-ON”
IA “ON” Mains O.K. Mains O.K.
Mains Failure
Signal after exter inverted relay
MCB logic = ”CLOSE-OFF” nal
+
NOTE: In the case MCB Logic = “CLOSE-OFF” it is necessary to change externally the polarity of the outputsignal.
ReturnFromTEST [MANUAL / AUTO]The set point influences the behavior of the TEST mode.
MANUAL:1) Select TEST, gen-sets starts and running unloaded
Battery
-
iLDO 4
MCB
AUX.INVERTING
RELAY
7/21/2019 IA NT PWR 2.0 Reference Guide
http://slidepdf.com/reader/full/ia-nt-pwr-20-reference-guide 66/92
InteliATSNT PWR, SW version 2.0, ©ComAp – June 2010 66IA-NT- PWR-2.0-Reference Guide.pdf
ON/OFF or wait for power-cut.2) To transfer load from mains to the gen-set press MCB3) When mains recovers, the gen-set remains running loaded.
CBb) After the Transfer Del delay InteliATSNT closes the MCB.
c) The gen-set is cooled and stopped
4) To stop the gen-set select AUTO Mode5) In AUT Mode:
a teliATS) After the MainsReturnDel In NT opens the G
AUT:1) Select TEST, gen-sets2
starts and running unloadedr the power-cut. the controller does not response) To transfer load from mains to the gen-set wait fo
for MCB ON/OFF button.3) When the mains recovers:
ens the GCBnsfer Del d CB.ains runnin
Opens On [MAINSFAIL / GENRUN]
a) After the MainsReturnDel the controller opb) After the Tra elay the controller closes the M
4) The gen-set rem g.5) To stop the gen-set select a different mode than TEST.
MCBMAINSFAILThe command to open the MCB is given immediately after mains fail condition evalu
ated.
RUNGENsetpoint
EmergStart Del), reaches proper voltage and frequency and Min Stab Time elapses. After that, theed and the GCB is closed after the timer elapses.
The command to open the MCB is not given till the Gen-set starts (with respecting the
MCB is opened, Transfer Del timer is start NOTE:This option should be used for MCBs using 230V control and not equipped with the undervoltage coil.
this timer starts. After the timer elapses the state of BI:
feedback del setpoint is longer then 60.0 s it means there is NO TIMEOUT.
ackDel [s]g binary output MCB close/open this timer starts. After the timer elapses the state of BI:
aluated.NO TIMEOUT.
O TIMEOUT.
GCBFeedbackDel [s]
After closing binary output GCB close/openGCB feedback is evaluated.If the setting of the GCBStep: 0.1sRang 0 – 60.0 s, 60.1 s = NO TIMEOUT.e:
MCBFeedb After closinMCB feedback is evIf the setting of the M fe ck delCB edba setpoint is longer then 60.0 s it means there isStep: 0.1s
– 60.0 s, 60.1 s = NRange: 0
Sync Ctrl
Voltage Window [%]This setpoint adjusts maximum allowed difference between generator and mains/bus voltage inrespective phases for passive synchronizing:Step: 1 %Range: 0 – 30 %Default: 10 %
7/21/2019 IA NT PWR 2.0 Reference Guide
http://slidepdf.com/reader/full/ia-nt-pwr-20-reference-guide 67/92
InteliATSNT PWR, SW version 2.0, ©ComAp – June 2010 67IA-NT- PWR-2.0-Reference Guide.pdf
d difference between generator and mains/bus frequency inve
Freq Window [Hz]This setpoint adjusts maximum allowerespe phases for passivecti synchronizing:
1 HzStep: 0.Range: 0.0 – 2.0 Hz (0.0 – 0.3 Hz for CLOSED transition)Default: 0.2 Hz
HINT:This setpoint de n trans ion typepe ds on it selected (setpoint Transition). If Closed transition takesplace Frequenc W oint valuy indow setp es above 0.3 Hz are internally limited to value of 0.3 Hz.
mum time interval when system waits for both sources to get synchronized.hat ti nization timeout alarm is activated and either changeover is interrupted orues a n delayed transition. See Transition setpoint description for more details, please.
Step: 1 min1 – 60 min
Default: 1 min
Sync Timeout [min]This setpoint adjusts maxi After t me synchrocontin s ope
Range:
Date/Time
Time Stamp Per [min]
00m
Time interval for periodic history records.Step: 1 minRange: 0 – 2 in NOTE: Time stamps are only recorded into history while gen-set is running. When is engine stopped there areno time stamps records made.
SummerTimeMod [DISABLED / WINTER / SUMMER, WINTER-ER-S]
switching between summer and wintertime is disabled.mer and wintertime is enabled and it is set to
ER-S) : Modification for southern hemisphere.
[DDMMYYYY]
.. Fail Blk /
It is following Timer functions. Binary output Exerc Timer X is alwaysactivated when Timer is active regardless of chosen Timer function. Timer functions require controllerrunning in AUT mode.No Func: There is no any other io ut binary output Timer1..2 activation.TEST: When this option is chosen then the Timer output is also internally connected to the
Remote TEST binary input.TEST OnLd: When this option is chosen then the Timer output is also internally connected to the
Rem TEST OnLd binary input.MFail Blk: When this option is chosen then the Timer output is also internally connected to the
MainsFailBlock binary input.
S, SUMMDISABLED: AutomaticWINTER (SUMMER) : Automatic switching between sumwinter (summer) season.WINTER-S (SUMM
Time [HHMMSS]Real time clock adjustment.
Date
Actual date adjustment.
Timer1 2Funct ion [No Func / TEST / TEST OnLd / MMode OFF]
possible to choose out of 5
funct n, b
7/21/2019 IA NT PWR 2.0 Reference Guide
http://slidepdf.com/reader/full/ia-nt-pwr-20-reference-guide 68/92
InteliATSNT PWR, SW version 2.0, ©ComAp – June 2010 68IA-NT- PWR-2.0-Reference Guide.pdf
Mod ption is chosen then the Timer output is also internally connected to thebinary input.
DNESDAY/FRI
T-SUN]s TIME is internally linked with Rem Start/Stop binary
MON AY, Y, WEDNESDAY, FRIDAY, SATURDAY, SUNDAY:activated on daily basis.
SAT-SUN:d on selected day interval.
imectivates.
Timer1..2Durationimer output is active.
1 min
e OFF: When this oRemote OFF
Timer 1..2 Repeat[NONE/MONDAY/TUESDAY/WEDNESDAY/THURSDAY/WE
DAY/SATURDAY/SUNDAY/MON-FRI/MON-SAT/MON-SUN/SADefine R 1 activation. Binary output TIMER 1input. Refer to binary inputs for details.
NONE: Timer function is disabledD TUESDAY, WEDNESDAY, THURSDA
Timer isMON-FRI, MON-SAT, Timer is activate
Timer1..2 ON TDay t en Time wh imer output a
Duration of TStep:Range: 1 – 1440 s
SMS/E-Mail
Remote alarm messagingIf a GSM modem and/or Internet Bridge is connected to the controller, the controller camessages and/or emails in the mo
n send SMSment when a new alarm appears in the Alarm list. The message will
contain a copy of the Alarm list.
Msg, whichs shall be announced (red/yellow/both) and also enter valid GSM phone number and/or
il address to the setpoints TelNo/Addr Ch1 and TelNo/Addr Ch2. It is possible to put either a
To enable this function, you should select with setpoints Yel Alarm Msg and Red Alarmlevels of alarme-maGSM number or e-mail to both setpoints.
NOTE: An internet module be ilable for sending of e-mails. Smust ava imilarly, a GSM modem is necessary forsending of SMS.
NOTE: There are 5 attempts for any active call (SMS/E-Mail). Timeout for connection is 90 sec and after 120sec controller starts the next attempt. During the time the IA-NT is trying to send an active call type,incoming calls are blocked.
Set this setpoint to YES if you want to get messages when a yellow (warning) alarm occurs.
Yel Alarm Msg [DISABLED, ENABLED]
NOTE: The target address (GSM phone num e ail address) must be set correctly to the setpoint(s)ber or -mTelNo/Ad r Ch1 resp. TelNo/Addr Ch
Red Alarm Msg [DISABLED, ENABLED]Set this setpoint to YES if you want to get messages when a red (shutdown) alarm occurs.
d 2.
7/21/2019 IA NT PWR 2.0 Reference Guide
http://slidepdf.com/reader/full/ia-nt-pwr-20-reference-guide 69/92
InteliATSNT PWR, SW version 2.0, ©ComAp – June 2010 69IA-NT- PWR-2.0-Reference Guide.pdf
NOTE: The target address (GSM phone number or e-mail address) must be set correctly to the setpoint(s)TelNo/Addr Ch1 resp. TelNo/Addr Ch2.
he alarm messages
e value of this parameter. If it consist „@“ it issup osed to be e-mail address and active e-mail is sent. If the value is number, without „@“, it is
TelNo/Addr Ch1, 2Enter either a valid GSM phone number or e-mail address to this setpoint, where t
shall be sent. Type of active call is considered from thp
supposed to be the telephone number and active SMS is sent.
NOTE: For GSM numbers use either national format (i.e. like number you will dial if you want to make a localcall) or full international format with "+" character followed by international prefix in the begining.This setpoint can be modified from PC only!
7/21/2019 IA NT PWR 2.0 Reference Guide
http://slidepdf.com/reader/full/ia-nt-pwr-20-reference-guide 70/92
InteliATSNT PWR, SW version 2.0, ©ComAp – June 2010 70IA-NT- PWR-2.0-Reference Guide.pdf
onFunction Descripti
Operating modes
Selection of the operating mode is done through Mode buttons on the front panel or by changing of theController mode setpoint (from the front panel or remotely).
NOTE: If this setpoint is configured as password-protected, correct password must be entered priorattempting to change the mode.
NOTE: Mode can not be changed, if Access Lock input is active.
T r g binary inputs that can be used to force one respective operating modei e the mode setpoint selection:
•
he e are followinnd pendently on
Remote OFF • Remote MAN • Remote AUT • Remote TEST • Rem TEST OnLd
If the respective input is active the controller will change mode to the respective position according torities of the
he priorities matches the order in the list above. If all inputs are deactivated the mode williven by the setpoint.
in OFF mode depends mainly on setting of the ActivityAtOff
the active input. If more inputs are active the mode will be changed according to prioinputs. Treturn to the original position g
OFFThe behavior of the controller setpoint.
No activitySetpoint ActivityAtOff = DISABLED.
The controller opens all binary outputs and Fault reset is active all the time.
Standard activitySetpoint ActivityAtOff = ENABLED.
oadingThe GCB will be opened and the engine will be immediately stopped in this mode without unland cooling. The MCB is closed permanently (MCB Opens On = GENRUN) or is open oaccording to the mains is present or not (
r closedMCB Opens On = MAINSFAIL). No AMF (A
- evaluates Mains failure / return) function will be performed. Buttons MCB, GCB, ST
including the appropriate binary inputs for external buttons are not active. Output
uto Mains Failure ART, STOP
GenStart/Stop is notd.
nd STOP buttons (or external buttonswired to appropiate binary inputs) in MAN mode. This will activate/deactivate GenStart/Stop
energize
MANThe engine can be started and stopped manually using START a
binaryoutput which polarity depends on GenStart Logic setpoint. When the engine is running, GCB can beclosed to a dead bus. Also MCB can b s nd opened manually using the MCB button,regardless the mains is present or not. No autostart is performed. No reaction to the input Rem
e clo ed a
Start/Stop.
NOTE:
The engine can run without load unlimited time. The controller does not automatically stop the runninggen-set in MAN Mode and does not start the gen-set when power cut comes.
7/21/2019 IA NT PWR 2.0 Reference Guide
http://slidepdf.com/reader/full/ia-nt-pwr-20-reference-guide 71/92
InteliATSNT PWR, SW version 2.0, ©ComAp – June 2010 71IA-NT- PWR-2.0-Reference Guide.pdf
NOTE: The breakers are internally locked to close two voltages against each. The controller will automaticallyrecognize if the breaker can be closed, it means it is never possible to close both breakers together
NOTE: If some voltage arises on generator bus (e.g. gen-set was started externally - not via IA-NT), generator
LED blinks and [Stop], [MCB], [GCB] buttons are inactive. To bring them into operation [Start] buttonhas to be pressed - it will synchronize IA-NT with gen-set state.
C AUTION! The MCB can be opened manually in MAN mode. Accidental opening the MCB will cause the object(load) will remain without power!!!
AUTThe engine is started and stopped either by the binary input Rem Start/Stop or by thmechani
e AMFsm or by the manual transfer request via Rem Transfer binary input. Buttons MCB, GCB,
not active. The full startthe moment when the engine is loaded is automatic as well as unloading and stop
re
• and no next
• Gen-set Start/Stop signal stays activeet parameters are OK (means GenReadyToLoad signal is activated or
generato d limits) and then G reclosedFo n Voltage nough to
w e off po l setpoint
s
START, STOP including the appropriate binary inputs for external buttons aresequence up tosequence.
The controller behavior when gen-set is stopped and restarted again whilst the mains failuconstantly persists:
If the problem on the gen-set side appears, all faults messages are auto-quitoperation is be blocked
• Controller waits for gen-sr voltages are in allowe CB is
• re
r ensuring GCB Open/Close output remains off whilst Ge is OK long eind the Circuit breaker to th sition use the Transfer De
AMF equence (simpl if ied)
State Condition of the transition Action Next stateMains failed1 or MCB feedback dropout
INSFAILMCB CLOSE/OPEN oEmergStart Del timer started
Mains failureMCB Opens On = MA
ffMainsoperatio
edbackRUN
Mains failuren
Mains failed1 or MCB feMCB Opens On = GEN
dropout EmergStart Del timer started
Mains voltage and frequency OINSFAIL on
Mains operationK After elapsing MCB CMCB CLOSE/OPENMCB Opens On = MA
lose Del
Mains voltage and frequency OMCB Opens On = GENRUN
Mains operationK None
EmergStart Del elapsedMCB Opens On = MAINSFAIL
nce perf ,then
o
Island operationEngine start seque ormed
GCB CLOSE/OPEN n 2
Mainsfailure
EmergStart Del elapsedMCB Opens On = GENRUN
ce performed,EN off, time
lay Transfer Del performed and2
Island operationEngine start sequenthen MCB CLOSE/OPdeGCB CLOSE/OPEN on
Islandoperation
Mains voltage and frequency OK MainsReturnDel timer started Mains return
Mains failed Island operationMainsreturn MainsRetu Del elapsed GCB CLOSE/OPEN off, then after
Transfer Del MCB CLOSE/OPENon and then engine stop sequenceperformed 3
Mains operationrn
1 Mains failed means mains over/under -voltage, over/under -frequency, voltage assymetry (preset
delay must elapse)
7/21/2019 IA NT PWR 2.0 Reference Guide
http://slidepdf.com/reader/full/ia-nt-pwr-20-reference-guide 72/92
InteliATSNT PWR, SW version 2.0, ©ComAp – June 2010 72IA-NT- PWR-2.0-Reference Guide.pdf
lay MCB Close Del2 If during start-up sequence mains returns, then MCB is reclosed with de (ifopened, depending on MCB Opens On setpoint) and start-up sequence is interrupted.
cooling) again, stop sequence is interrupted, MCB opened and3 If mains fails during stop procedure (GCB reclosedclosed with delay Transfer Del.
chapters: Circuit breakers timingSee also and AMF time chart.
W ARNING! If an red alarm is present and the gen-set is in AUT mode, it can start by self after all red alarmsbecomes inactive and are acknowledged!!!
of the controller in TEST mode depends mainly on setting of the ReturnFromTEST
TESTThe behaviorsetpoint.
Automatic returnSetpoint ReturnFromTEST = AUTO.
The gen-set will be started when the controller is put to TEST mode and will remain running unloaded.If a mains failure occurs, the MCB will be opened and after Transfer Del the GCB will be closed and
Af ter mains is recovered, the delay MainsReturnDelthe gen-set will supply the load. will countains is stil l ok, the controller will transfer the load back to the
ged.down and i f elapses and the mmains and the gen-set will remain running unloaded again unti l the mode is chan
Manual returnSetpoint ReturnFromTEST = MANUAL.
The d when the controller is put to TEST mode and will remain running unloaded.
sferred to the gen-set also manually:
ansfer Del
gen-set will be starteIf a mains failure occurs, the gen-set will take the load after it has started.
The load can be tran
• If the MCB button is pressed, the controller will open the MCB, then wait for Tr and
il the controller is
Test with load
finally close the GCB.
Once the load is supp lied by the gen-set, the gen-set remains supplying it untswitched to other mode.
the gen-lly make a
, wait for Transfer Del
If the binary input Rem TEST OnLd is activated, the controller is switched to TEST mode (i.e.set will be started as described above), but once started the controller will automaticaswitchover, i.e. open MCB and close GCB.
to previouscontroller
will either stay supplying the load if the mains is failed, or will transfer the load back to the mains.
After the binary input Rem TEST OnLd has been deactivated, the controller goes backoperation mode and it's behavior depends on it. In most cases it will be AUT mode and the
Periodic exercisesThe output from the Exerc timer 1 is internally connected to the Remote TEST binary input to enable
testing of the gen-set.
The controller must have AUT mode selected by mode buttons and other "mode forcing" binary inputsmust not be active to ensure proper function of the exercise.
periodic
NOTE: If a shutdown or other red alarm comes while the load is supplied from the gen-set and the mains ishealthy, the load is switched back to the mains.
C AUTION! The gen-set starts automatically and is always running in TEST mode!
7/21/2019 IA NT PWR 2.0 Reference Guide
http://slidepdf.com/reader/full/ia-nt-pwr-20-reference-guide 73/92
InteliATSNT PWR, SW version 2.0, ©ComAp – June 2010 73IA-NT- PWR-2.0-Reference Guide.pdf
Circuit breakers timing
Relation between Mains fail and MCB and start of gen-set
M
etected as Mains <V, Mains >V, Mains V Unbal, Mains <Freq, Mains >Freq. After
CB Opens On = MAINSFAIL:
Mains fail is ddetection MCB is opened.
NOTE: When MCB feedback drop-out and measured mains electrical limits (voltage, frequency) are still inlimits, the controller switches MCB ON again.
EmergStart Del
Mains fail
MCBopened
Mains V Del or Mains Freq
Del or Mains VUnb Del
genset start
MCB Opens On = GENRUN:
The MCB is not opened till the engine starts and gets ready to take the load.
Transfer Del
Engine started
MCB opened
MinGenStabTime
GCB closed
MaxGenStartDel
Relation between Mains return and MCB
OFF Mode, GCB and MCB are opened
Mains return
MCB closed (only when genset isnot running and GCB is opened)
M BC Close Del
7/21/2019 IA NT PWR 2.0 Reference Guide
http://slidepdf.com/reader/full/ia-nt-pwr-20-reference-guide 74/92
InteliATSNT PWR, SW version 2.0, ©ComAp – June 2010 74IA-NT- PWR-2.0-Reference Guide.pdf
Ren-set loaded.
Mains returns: GCB opens (according 3., MainsReturnDel), MCB closes (Transfer Del)
elation between GCB and MCBConditions: AUTO Mode, Mains =off, MCB = opened, GCB = closed, g
GCB opened
MCB closed
Transfer Del
Relation between GCB and MCB (Test mode)
Situation 2: ReturnFromTEST=MANUAL, Mains =OK, MCB is closed, gen-set is running.Press MCB on/off -> MCB opens, GCB closes (Transfer Del), gen-set is running loaded.
Situation 1: Mains =OK, MCB = closed, GCB = opened, RPM=0.Change mode to TEST: gen-set starts, GCB = opened.Mains cut: MCB opens (according 1.), GCB closes (Transfer Del)
MCB opened
GCB closed
Transfer Del
7/21/2019 IA NT PWR 2.0 Reference Guide
http://slidepdf.com/reader/full/ia-nt-pwr-20-reference-guide 75/92
InteliATSNT PWR, SW version 2.0, ©ComAp – June 2010 75IA-NT- PWR-2.0-Reference Guide.pdf
nt
F re available:
• Tripre
Alarm Manageme
ollowing alarms a• Warning
• Mains failu
Warning (WRN)
When warning comes up, only alarm outputs and common warning output are closed.
warnings:ossible events
PossibleSee List of p
Trip (TRP)
When the trip alarm comes up, InteliATSNT opens outputs GCB CLOSE/OPEN, GENSTART/STOPp the engine immediately. Alarm outputs and common shutdown output are
closed. Active or not reset protection disables start.
s:
and PRESTART to sto
Possible shut-down alarmSee List of possible events
Mains failure (MF)
Mains failure detection depends on Auto mains fai lure (AMF) setpoints (levels and delays) adjusting.p, mains circuit breaker is opened.
Possible mains failure reasons:See List of possible events
When the mains failure comes u
NOTE: Mains failure is not written to alarm list!
7/21/2019 IA NT PWR 2.0 Reference Guide
http://slidepdf.com/reader/full/ia-nt-pwr-20-reference-guide 76/92
InteliATSNT PWR, SW version 2.0, ©ComAp – June 2010 76IA-NT- PWR-2.0-Reference Guide.pdf
AMF t ime chart – genset OK
AMF t ime chart – genset not started properly
NOTE: For more details please see the:* AMF Sett ing: MinStabTime & MaxStartDel setpoint description,** AMF Sett ing: MCB Opens On & Transfer Del setpoint description,*** AMF Sett ing: MCB Close Del setpoint description
7/21/2019 IA NT PWR 2.0 Reference Guide
http://slidepdf.com/reader/full/ia-nt-pwr-20-reference-guide 77/92
InteliATSNT PWR, SW version 2.0, ©ComAp – June 2010 77IA-NT- PWR-2.0-Reference Guide.pdf
Voltage phase sequence detection
InteliATSNT controller detects phase sequence on both generator and mains/bus vThese protections are important after c
oltage terminals.ontroller installation to avoid wrong voltage phases phase
s can be detected:
The T controller L1, L2, L3. When the phases areconn 2, L1, L3) following alarms are detected:
ng generator phase sequence
t CB
tection – see following diagrams.
When is BO GCB close/open (MCB Close/Open) in steady state and GCB feedback (MCB feedback)is changed the GCB fail is detected immediately (no delay).
connection. Following alarm
Wrong phase sequencere is fix defined phase sequence in InteliATSN
ected in different order (e.g. L1, L3, L2 or LGen CCW Rot = wroMains CCW Rot = wrong mains phase sequence
GCB, MCB fail detect ionMCB or GCB fail detection is based on binary output CB close/open comparing with binary inpufeedback.There are three different time delays for CB fail de
Alarm: G CB fail
BI GCB feedback
BO G CB c lose/open
Alarm detect ion:immediatelly
Alarm: G CB fail
BO G CB close/open
BI GCB f eedback
Alarm detect ion:immediatelly
closed
opened
active active
opened
closed
When BO GCB close/open (MCB Close/Open) opens there is 5 sec delay for GCB fail (MCB fail)detection.
Alarm: G CB fail
BO G CB c lose/open
BI GCB f eedback
active
opened
opened
Time delay
5 sec
When BO GCB close/open (MCB Close/Open) closes, there is 5sec delay for GCB fail (MCB fail)detection:
Alarm: GC B f ail
BI GCB feedback
active
closed
closed
BO G CB close/open
Time delay
5 or 2 sec
NOTE: You can solve state of MCB fail by pressing Fault Reset button.
7/21/2019 IA NT PWR 2.0 Reference Guide
http://slidepdf.com/reader/full/ia-nt-pwr-20-reference-guide 78/92
InteliATSNT PWR, SW version 2.0, ©ComAp – June 2010 78IA-NT- PWR-2.0-Reference Guide.pdf
tes
ic s
per
Gen-set Operation Sta
Electr tate machine
MainsO Mains is presentMainsFlt off – immediate stateMains cutMainsFlt es EmergStart delMains cut off – takIslOper Island operationMainsRet Mains recoverBrks Off GCB, MCB openedMinStabTO Minimal Stabilization TimeoutMaxStabTO Maximal Stabilization TimeoutTrans Del Forward return break delay. Delay between GCB opening and MCB closing
L ssib venist of po le e ts
Eventsspecification
Protectiontype
Information on binaryoutput available (Seelist of Binary outputs)
Description
Wrn Batt Volt WRN YES its given by Batttpoints.
Battery voltage is out of limUndervolt/Batt OverVolt se
Binary input Configurable YES Configurable Warning/Shutdown alarms onts of IA-NT.the inpu
Trp BatteryFlat TRP YES during startingn it
nd activates this
If the controller switches offsequence due to bad battery conditiodoesn’t try to start again aprotection.
Trp Start Fail TRP YES Gen-set start failed.
ParamFail NONE NO meters. Happendsnew firmware orr. The controller
all parameterseter.
Wrong checksum of paratypically after downloadingchanging of the parametestays in INIT mode. Checkand write at least one new param
Trp Gen Lx >,<V TRP YES is out of limits givenSd setpoints.
The generator voltageby Gen <V Sd and Gen >V
Trp Gen V Unbal TRP YES nerator voltage is unbalanced morenbal Sd setpoint.
The gethan the value of Volt U
Trp Gen >Freq TRP YES cy is out of limitsand Gen <Freq Sd
The generator frequeq Sd
engiven by Gen >Fr setpoints.
Wrn Amps Unbal TRP NO unbalanced.The generator current is
Trp Overload TRP YES ter than the value given byThe load is greaOverload setpoint.
EmergencyStop TRP NO p is openedctivated.
If the input Emergency Stoshutdown is immediately a
GCB Fail TRP NO r circuit breaker.Failure of generatoMCB Fail MF NO Failure of mains circuit breaker.Wrn GeStateNA WRN NO Neither GenerProtect enabled nor BI
GenReadyToLoad defined. At least onemust be enabled / configured.
Trp GenRd Fail TRP NO Signal BI GenReadyToLoad lostWrn Stop Fail WRN YES Gen-set stop failed. The alarm appears if
the STOP command fails and the STARTcommand was issued before.
Low BackupBatt WRN NO RTC backup battery is flat
7/21/2019 IA NT PWR 2.0 Reference Guide
http://slidepdf.com/reader/full/ia-nt-pwr-20-reference-guide 79/92
InteliATSNT PWR, SW version 2.0, ©ComAp – June 2010 79IA-NT- PWR-2.0-Reference Guide.pdf
History file
InteliATSNT stores a record of each important event into the history file. The history file seats 117rds. When the history file is full, the oldest records are removed.reco
NOTE
:
To force history download in LiteEdit (direct, modem or Internet) open History window and selectHistory | Read history command.
ord s
breviati cal value
Rec tructure
Ab on Histori
Num Number of historical eventReason Event specificationDate event in format DD/MM/YYDate of historicalTime al event in format HH:MM:SSTime of historicMode deController’s moPwr rGenerator active powePF Generator PF
LChr e loadCharacter of thGfrq uencyGenerator freqVg1 ge L1Generator voltaVg2 age L2Generator voltVg3 oltage L3Generator vIg1 urrent L1Generator cIg2 current L2GeneratorIg3 rrent L3Generator cuVm1 L1Mains voltageVm2 Mains voltage L2Vm3 Mains voltage L3Mfrq Mains frequencyUBat Battery voltage
BIN Binary inputs IA-NTBOUT Binary outputs IA-NT
7/21/2019 IA NT PWR 2.0 Reference Guide
http://slidepdf.com/reader/full/ia-nt-pwr-20-reference-guide 80/92
InteliATSNT PWR, SW version 2.0, ©ComAp – June 2010 80IA-NT- PWR-2.0-Reference Guide.pdf
gingRemote Control and Data Log
Direct connection to the PC
InteliATSNT can be connected directly with PC via optional IL-NT RS232 interface.NTUse the standard serial cable to connect PC with InteliATS .
NOTE: Make sure the grounding system on controller and PC – COM port (negative of the PC DC supply) areidentical – before the first direct connection. There must not be any voltage between these two pointsotherwise the internal reversible fuse in controller burns out. The simple solution is to assure, that thePC supply 240/20V is ground free (GND terminal is not connected).
5 - GND
2 - RxD3 - TxD
PC
5 - GND
2 - RxD3 - TxD
R S 2 3 2
R
S 2 3 2
230 VAC
0 V D C
CONTROLLER
+-Battery
Required the samevoltage potentialbetween GND‘s
RS 232
PC software – LiteEdit
On the PC (for direct or modem connection) has to be installed the ComAp’s software packagedows 95 or newer platform)
rselect software configuration
modify password, commands protectionsd on
M
LiteEdit. (based on WinLiteEdit enables:read the quantitiesadjust all set pointscontrol the engineconfigure the controlle
modify alarm inputs and outputs
irect, modem or Internet communicati
odbus protocol
T ion of the function of iL serial port is done via the setpoint COMx Mode in Basic settings
• Function 3 (Read Multiply Registers)• Function 6 (Write Single Register)• Function 16 (Write Multiply Regis• The sponse to an incoming messa s nt with minimum 4.096 ms delay after message
reception
The complete description of Modbus communication protocol can be found in Modbus ProtocolReference Guide PI-MBUS-300 and Open Modbus Specification Release 1.0. Both documents are
available from web site at http://www.modicon.com/openmbus/
he select
• 57600 bps, 8 data bits, 1 stop bit, no parity• Transfer mode RTU
ters)re ge i se
.
7/21/2019 IA NT PWR 2.0 Reference Guide
http://slidepdf.com/reader/full/ia-nt-pwr-20-reference-guide 81/92
InteliATSNT PWR, SW version 2.0, ©ComAp – June 2010 81IA-NT- PWR-2.0-Reference Guide.pdf
Communication object vs. Register All the data intended for communication has its representation as communication objecontroller. The communication object is represented by the n-byte array in the controllidentified by the unique 16-bit communication object number. The register, according tcommunication protocol, represents a two-byte data and in communication functions i16-bit register address. Further in the description of communication functions the com
object number will always b
cts in theer memory ando Modbuss referenced bymunication
e used as a register address and length of the communication objectwill be expressed by number of registers. Just one communication object can be read or writ tenby one communication function.
NOTE: To obtain communication object numbers it is possible to download the actual controller descriptionon-line from controller or from (ail) archive and use “export data” function from LiteEdit software.
C nica lis d de N arc
ommu tion object t (exporte from fault IA- T-PWR hive)
Setpoints o fe re ve r n
IA-NT PWR:Nam Firmwa r. Application Date App. ve . Ser. um. Filename
IA-NT-PWRIA-NT-1.2.3
1.2010.201 12 56
R:7.0PWR 8.1 1,2 34 78
IA-NT-PWR-
1.2.AILGroup Name ens. Pa C . o imit Data typeValue Dim ssword om bj. Lo limit Hi l
Basic Settin lerName PWR No 86 Short stringgs Control 37
Basic Settin Power 200 No 8 Unsigned 16gs Nominal kW 276 1 5000
Basic Settin urrent 350 No 8275 000 Unsigned 16gs Nomin C A 1 10
Basic Settin o 2000 No 8274 5000 Unsigned 16gs CT Rati /5A 1
Basic Settin 1,0 No 9579 500,0 Unsigned 16gs PT Ratio /1 0,1
Basic Settin atio 1,0 No 9580 Unsigned 16gs Vm PT R /1 0,1 500,0
Basic Settin l Volts 231 No 8277 20000 Unsigned 16gs Nomina V 80
Basic Settin Freq 50 No 8278 65 Unsigned 16gs Nominal Hz 45
Basic Settin FF BLED No 16 String listgs ActivityAtO ENA 1 20
Basic Settin lerMode OFF No 83 String listgs Control 15
Basic Settin llerAddr 1 Ye 453 32 Unsigned 8gs Contro s 2 7 1
Basic Settings COM1 Mode IRECT Yes String listD 24522Basic Settings COM2 Mode RECT Ye 445 String listDI s 2 1
Basic Settings GenStart Logic N No 910 String listCLOSE-O 0
Basic Settings Batt Undervolt 18,0 No 838 40,0 Integer 16V 7 8,0
Basic Settings Batt Overvolt 36,0 No 95 40,0 Integer 16V 87 18,0
Basic Settings Batt Volt Del 5 No 8383 0 600 Unsigned 16s
Engine Para Time 0 No 83 600 Unsigned 16ms Prestart s 94 0
Engine Para ime 0 No 82 Unsigned 16ms Cooling T s 58 0 3600
Engine Para 20 No 091 601 Unsigned 16ms Max Star tDel s 1 4 0
Engine Para ime 3 No 82 300 Unsigned 16ms Min Stab T s 59 1
Engine Para ime 60 No 981 Unsigned 16ms Stop T s 5 1 3601
Gener Prote t BLED No 10 String listct GenerProtec ENA 1 30Gener Prote ct Trp 250 No 82 500 Unsigned 16ct Short Cr % 82 100
Gener Prote ct Del 0,00 No 99 0,00 Unsigned 16ct Short Cr s 91 0,00 1
Gener Prote MT Del 4,0 No 82 60,0 Unsigned 16ct Amps ID s 83 1,0
Gener Prote nbal Trp 50 No 82 200 Unsigned 16ct Amps U % 84 1
Gener Protect Amps Unbal Del 5,0 No 8285 0,0 600,0 Unsigned 16s
Gener Prote rp 110 No 8291 200 Unsigned 16ct Gen >V T % 70
Gener Protect Gen <V Tr % No 8293 0 110 Unsigned 16p 70
Gener Protect Gen V Del s No 8292 0,0 600,0 Unsigned 163,0
Gener Protect Volt Unbal Trp 10 % No 8288 1 200 Unsigned 16
Gener Protect Volt Unbal Del 3,0 s No 8289 0,0 600,0 Unsigned 16
Gener Protect Gen >Freq Trp 110,0 % No 8296 85,0 200,0 Unsigned 16
Gener Protect Gen <Freq Trp 85,0 % No 8298 0,0 110,0 Unsigned 16
Gener Protect Gen Freq Del 3,0 s No 8297 0,0 600,0 Unsigned 16
AMF Settings RetFromIsland AUTO No 9590 String list
7/21/2019 IA NT PWR 2.0 Reference Guide
http://slidepdf.com/reader/full/ia-nt-pwr-20-reference-guide 82/92
InteliATSNT PWR, SW version 2.0, ©ComAp – June 2010 82IA-NT- PWR-2.0-Reference Guide.pdf
ng rt Del 5 No 83 Unsigned 16 AMF Setti s EmergSta s 01 0 6000
AMF Setting eturnDel 20 No 83 Unsigned 16s MainsR s 02 1 3600
AMF Setting Del 1,0 No 83 00,0 Unsigned 16s Transfer s 03 0,0 6
AMF Setting Close Del 1,0 No 838 60,0 Unsigned 16s MCB s 9 0,0
AMF Setting >V 110 No 83 150 Unsigned 16s Mains % 05 60
AMF Setting 60 No 830 110 Unsigned 16s Mains <V % 7 50
AMF Setting el 2,0 No 83 00,0 Unsigned 16s Mains V D s 06 0,0 6 AMF Setting V Unbal 10 No 84 150 Unsigned 16s Mains % 46 1
AMF Setting Unb Del 2,0 No 84 60,0 Unsigned 16s Mains V s 47 0,0
AMF Setting req 102,0 No 8310 Unsigned 16s Mains >F % 98,0 150,0
AMF Setting q 98,0 No 8312 102,0 Unsigned 16s Mains <Fre % 50,0
AMF Setting e 0,5 No 8311 60,0 Unsigned 16s Mains Freq D l s 0,0
AMF Setting N No 84 String lists MCB Logic CLOSE-O 44
AMF Setting TEST No 86 String lists ReturnFrom MANUAL 18
AMF Setting On N No 9850 String lists MCB Opens GENRU
AMF Setting ac 3,0 No 983 60,1 Unsigned 16s GCBFeedb kDel s 6 1,0
AMF Setting 3,0 No 9056 60,1 Unsigned 16s MCBFeedbackDel s 1,0
Date/Time mp Per 60 No 8979 240 Unsigned 8Time Sta min 0
Date/Time meMo BLED No 8727 String listSummerTi d DISADate/Time :00 No 45 TimeTime 0:00 2 54
Date/Time .2006 No DateDate 1.1 24553
Date/Time peat NE No 00 String listTimer1 Re NO 1 45
Date/Time Timer1 ON Time No Time5:00:00 10042
Date/Time uration 5 No 1440 Unsigned 16Timer1D min 10044 1
Date/Time epeat NONE No String listTimer2 R 10202
Date/Time Time No TimeTimer2 ON 5:00:00 10199
Date/Time ration 5 No 1440 Unsigned 16Timer2Du min 10201 1
SMS/E-Mail Yel Alarm Ms String listg OFF No 8482
SMS/E-Mail Red Alarm Msg No String listOFF 8484
SMS/E-Mail TelNo/Addr Ch1 No Long string9597
SMS/E-Mail /Addr Ch2 N 9598 Long stringTelNo o
Values o WR:e mware ver. A on D r. Ser. num. Filename
f IA-NT PNam Fir pplicati ate App. ve
IA-NT-PWIA-NT-1.0
3.01.200917.2.2009 12345678 IA-NT-PWR-1.0.AILR
R:2PWR 1,0
Group Name Dime j. Data typeValue nsion Com. ob
Generator kW 02 Integer 16Gen kW 150 82
Generator L1 50 kW 24 Integer 16Gen kW 85
Generator L2 50 kW 25 Integer 16Gen kW 85
Generator L3 50 kW 26 Integer 16Gen kW 85
Generator n kVAr 15 kVAr 03 Integer 16Ge 82
Generator L1 5 kVAr 8527 Integer 16Gen kVAr
Generator L2 5 kVAr 28 Integer 16Gen kVAr 85Generator L3 5 kVAr Integer 16Gen kVAr 8529
Generator 153 kVA Integer 16Gen kVA 8565
Generator VA L1 51 kVA 30 Integer 16Gen k 85
Generator 2 51 kVA 8531 Integer 16Gen kVA L
Generator kVA L3 51 kVA Integer 16Gen 8532
Generator F 1,00 Integer 8Gen P 8204
Generator Gen Load Char R 8395 Char
Generator Gen PF L1 8533 Integer 81,00
Generator Gen Ld Char L1 R 8626 Char
Generator Gen PF L2 1,00 8534 Integer 8
Generator Gen Ld Char L2 R 8627 Char
Generator Gen PF L3 1,00 8535 Integer 8
Generator Gen Ld Char L3 R 8628 CharGenerator Gen Freq 50,0 Hz 8210 Unsigned 16
Generator Gen V L1-N 230 V 8192 Unsigned 16
7/21/2019 IA NT PWR 2.0 Reference Guide
http://slidepdf.com/reader/full/ia-nt-pwr-20-reference-guide 83/92
InteliATSNT PWR, SW version 2.0, ©ComAp – June 2010 83IA-NT- PWR-2.0-Reference Guide.pdf
tor L2-N 230 V Unsigned 16Genera Gen V 8193
Generator L3-N 230 V Unsigned 16Gen V 8194
Generator L1-L2 398 V Unsigned 16Gen V 9628
Generator L2-L3 398 V Unsigned 16Gen V 9629
Generator V L3-L1 398 V Unsigned 16Gen 9630
Generator A L1 41 A Unsigned 16Gen 8198
Generator Gen A L2 41 A 8199 Unsigned 16Generator 3 41 A Unsigned 16Gen A L 8200
Mains L1-N 231 V Unsigned 16Mains V 8195
Mains L2-N 230 V Unsigned 16Mains V 8196
Mains L3-N 230 V Unsigned 16Mains V 8197
Mains V L1-L2 398 V Unsigned 16Mains 9631
Mains Mains V L2-L3 398 V 9632 Unsigned 16
Mains Mains V L3-L1 398 V 33 Unsigned 1696
Mains Mains Freq 50,0 Hz 11 Unsigned 1682
Controller Volts 24,3 V 13 Integer 16I/O Battery 82
Controller ts 35 Binary 16I/O Bin Inpu [1111001] 82
Controller utputs Binary 16I/O Bin O [1111000] 8239
Statistics 0 Integer 32Energy kWh 8205
Statistics h 0 Integer 32Energy kVAr 8539
Statistics tarts 0 Unsigned 16Num S 8207
Statistics adStarts 0 5 Unsigned 32Num B 1119
IA Info ate ##### 5 Unsigned 16Breaker St 845
IA Info ##### Unsigned 16Timer Text 8954
IA Info Timer Value 0 s 8955 Unsigned 16
IA Info FW Version 0,0 8393 Unsigned 8
IA Info Application 19 8480 Unsigned 8
IA Info FW Branch 10 8707 Unsigned 8
IA Info PasswordDecode ##### 9090 Unsigned 32
Date/Time Time ##### 24554 Time
Date/Time Date ##### 24553 Date
7/21/2019 IA NT PWR 2.0 Reference Guide
http://slidepdf.com/reader/full/ia-nt-pwr-20-reference-guide 84/92
InteliATSNT PWR, SW version 2.0, ©ComAp – June 2010 84IA-NT- PWR-2.0-Reference Guide.pdf
ionRemote Communicat
NOTE:Refer to InteliCommunication guide for all additional information.
Internet connection
d from InteliMonitor or LiteEdit over the Internet using IB-Lite
DN modem
IA-NT controllers can be monitoreplug-in.
Recommended IS
•
• Develo Microlink ISDN i
R c
Askey TAS-200E• ASUScom TA-220ST
e ommended GSM modem
• Siemens M20, TC35, TC35i, ES75, MC39200/WMOD2
T recommended)Hz.
GSM Modem setup
P r n following program for GSM proper setup.Program writes all the necessary AT commands to configure the GSM modem properly for use withI
_setup.exe.Select COM port
ress S
• Wavecom M1• Wavecom - Maestro 20, dual 900/1800MHz.• Wavecom – Fastrack M1306B, dual 900/1800 MHz (Fastrack M1206B is NO• FALCOM A2D, dual 900/1800M
rio to start work with GSM modem ru
A-NT.This program runs independent on LiteEdit:
• Start MS Windows-Start-Program files - LiteEdit –Gm•
• Select iG-CU (=IS-CU) or iG-MU unit• P etup button
Follow command M Modem Setup w Typical real baud rate for GSM data communication s.
• s in GS indow
is 80 to 90 Bp
NOTE: It is strongly recommended to use the same type of modem on the both sides (IA and PC) ofc
Mobile SIM card setting
onnection.
Analogmodem
Analog GSMmodem
GSMmodemormodem
• Adjust SIM card in GSM modem following way:• enable data connection (when required)• no PIN code
7/21/2019 IA NT PWR 2.0 Reference Guide
http://slidepdf.com/reader/full/ia-nt-pwr-20-reference-guide 85/92
InteliATSNT PWR, SW version 2.0, ©ComAp – June 2010 85IA-NT- PWR-2.0-Reference Guide.pdf
ware
mote signallingIt is the optional
ible to upload into controller instead of standard controller’s fi rmware.
IL-NT-RD Remote display soft
This chapter describes Remote display software IL-NT-RD, which is designed as an reand control software for InteliATSNT, InteliLiteNT and InteliDrive Lite controllers.
software which is poss
General description
Remote display software works as “remote display and control” for the master InteliATSor InteliDrive Lite controller. Genset/Engines can be controlled
NT, InteliLiteNT from remote display as well as from
master controller. All remote display screens (Measure, Setpoints and History) displays the same datacontroller. Front panel buttons on both controllers work the same way. All remote display
LED’s shows the same state as corresponding LED’s on master controller.like master
Warning!
It is highly recommended to use thedisplay. Only in such case is assure
same type and model of controller for master and remoted the proper function o f all buttons, LED diods and display.
Another combinations of HW types and models from Master control ler and remote display are
tallation
not supported nor tested!
IL-NT-RD Software ins
The IL-NT-RD remote display firmware is installed in the same way as any other IA-NT firmware using
Reference guide for details about upgrading firmware. IL-NT-RDc t H stall back theorigi
• Open any type of online connection.• DDE server will try to open the connection, but it will fail and write red error message in the
status bar.• At this moment go to CONTROLLER -> PROGRAMMING AND CLONING -> PROGRAMMING and select
proper! firmware you want program to the controller. Choosing the wrong type of firmwaremay result in non-functional controller.
LiteEdit software. Please see LiteEditon ains only firmware, not an archive.
owever when there is IL-NT-RD firmware installed in the controller the procedure to innal standard firmware is following:
• Press "OK" button to programm the firmware to the controller.
7/21/2019 IA NT PWR 2.0 Reference Guide
http://slidepdf.com/reader/full/ia-nt-pwr-20-reference-guide 86/92
InteliATSNT PWR, SW version 2.0, ©ComAp – June 2010 86IA-NT- PWR-2.0-Reference Guide.pdf
oller, close the boot jumper and switch
• rcess
ns.• tus line and the
controller is blocked showing "Init" state. Use CONTROLLER -> RESET FROM INIT STATE menuitem to put the controller to normal operation. Be sure you have checked all setpoints before.
• It may be required to switch off power supply of contr on controller again. Follow the information windows accordingly. After programming is finished (it may be required to power off controller, open the boot jumpeand power it on again) open configuration window and perform the configuration promanually. There is no compatibility of the configuration between different firmware versio
In some cases the "wrong setpoints" message can occur in the DDE server sta
C AUTION! Check the statistic values after firmware upgrade. Readjust the values if necessary.
IL-NT-RD Wiring
IL-NT-RD can be connected to InteliATSNT, InteliLiteNT or InteliDrive Lite controller RS485 communication line. It is possibl
via RS232 ore to connect only up to two remote displays to one master
ing different communication COMs. It is not supported to connect two or morester
Connection processonnected. It
ddress 1to 32. Remote display tries two communication speeds 38400 bps and 56000bps.
Detecting…” on screen and progress bar below counts from 0 toprox. 10-15 seconds. Than is 5 seconds pause and process continuesr controller is found.
llers, not supported application, or controllers that are not properlying the search.
C nI e.
Tmote display can not connect with master controller:
o uppo ed type of controller connected (Eg. IGS-NT, ID-DCU, IC-NT, IGS-CU, etc.)2. Not supported firmware in master controller
tab troller4. Wrong settings o in master controller
g connectio
Direct RS232 connectionHW module: IL-NT-RS232
Master controller settings: ControllerAddr = 1..32COM1 Mode = DIRECT
Up to 2 meters: Recommended to use our standard AT-LINK cable.
controller, if they are usremote displays to one communication line, eg. RS485. It is possible to monitor only one macontroller from one remote display at the time.
Remote display after power on automaticaly starts to search for any master controller cstarts to search on COM1 from master controllers address 1 to 32 and later on COM2 from a
During this process is displayed text “100%. This process takes apagain until compatible maste Not supported types of controcomunicating are skipped dur
o troller type selectionL-NT-RD automatically detects controller typ
roubles with connectionThere are few reasons why re
1. N t s rt
3. Configuration le error in master conf setpoint COMx Mode
5. Wron n, wiring, communication fail
7/21/2019 IA NT PWR 2.0 Reference Guide
http://slidepdf.com/reader/full/ia-nt-pwr-20-reference-guide 87/92
InteliATSNT PWR, SW version 2.0, ©ComAp – June 2010 87IA-NT- PWR-2.0-Reference Guide.pdf
Up to 10 meters: r localthe three wires
communication:
L-NT/ID-Lite connector (D-SUB9 fem IL-NT-RD connector (D-SUB9 female)
Recommended to use standard Null-modem cable foconnection between controller and remote display, although(TxD, RxD, GND) RS 232 connection is enough for direct
IA-NT/I ale)RxD 2 3 TxD
TxD 3 2 RxDGND 5 5 GND
Remote RS485 and/or di rect RS232 connectionHW module: IL-NT-RS232-485Up to 1000 meters (only with RS485):
Case 1) RS232 / Master controller settings:ControllerAddr = 1..32
ECT
COM2 Mode = DIRECT
Case 3) 32 + RS485 / Master controller settings:ControllerAddr = 1..32COM1 Mode = DIRECTCOM2 Mode = DIRECT
It is possible to make a RS232 direct connection with IL-NT-RS232 module on one side and IL-NT-RS232-485 module on the other side.
COM1 Mode = DIR
Case 2) RS485 / Master controller settings:ControllerAddr = 1..32
RS2
7/21/2019 IA NT PWR 2.0 Reference Guide
http://slidepdf.com/reader/full/ia-nt-pwr-20-reference-guide 88/92
InteliATSNT PWR, SW version 2.0, ©ComAp – June 2010 88IA-NT- PWR-2.0-Reference Guide.pdf
ion using external RS232-RS422/485 converter:
485 bus0 or 56000 bps.
Any connected RS 232 to RS 422/485 converter has to be set to passive DSR signal (when DSR.
Al ternat ive connectRecommend external converter: ADVANTECH – ADAM 4520: RS232 to RS422/485 converter, DIN rail, automatic RSsupervision, no external data flow control signals, galvanic isolated, baud rate 3840
connected) after switch on
Function description
Remote display IL-NT-RD works as remote display and control of the master InteInteliDrive Lite controller. It is supposed and highly recommended that both, remotemaster are using the same HW type and model of controller. Another types and models of mastremote display are not supported nor tested. All remote display
liATSNT, InteliLiteNT ordisplay and
er and’s LEDs show the same state as
ork in the sameontroller. User can
s, set password, change setpoints and view history records.
All IL-NT-RD screens Init, Measure, Setpoints and History display the same data like in the master
Interruption of the serial line between master device and Remote display has no effect to the master
unication cannot beD’s are off.
nfiguration table
After the configuration from master is downloaded remote display jump to master controllers Initand blinking.
en to check it’s version and serial number of usedessing PAGE button for 3 seconds.
SW compatibility
corresponding LEDs on master controller. Front panel buttons on both controllers wway. Genset/Engine can be controlled from remote display as well as from master cswitch screen
controller.
Master device is always able to work without connected Remote display.
controller.
If the serial line between master device and remote display is interrupted, or commestablished, remote display shows it’s Init screen and message “Trying” and all LE Once remote display finds compatible master it shows “Preparing” and downloads cofrom master controller.
screen and all LEDs
It is possible to switch to remote displays Init screcontroller and communication status by pr
IL-NT-RD sw. version 1.0 is compatible with masters SW:
• All InteliATSNT standard software from ver. 1.0• All InteliLiteNT standard software from ver. 1.1• All ID-Lite standard software from ver. 1.0• Chosen InteliATSNT, InteliLiteNT and ID-Lite customer branches
Some of the future InteliATSNT, InteliLiteNT, ID-Lite versions may require upgrade of the IL-NT-RDsoftware.
7/21/2019 IA NT PWR 2.0 Reference Guide
http://slidepdf.com/reader/full/ia-nt-pwr-20-reference-guide 89/92
InteliATSNT PWR, SW version 2.0, ©ComAp – June 2010 89IA-NT- PWR-2.0-Reference Guide.pdf
eMaintenanc
Backup battery replacement
The internal backup battery should be replaced approx. every 5-7 years. Replace the battery, if the
1. Disconnect all terminals from the controller and remove the controller from the switchboard.2. Release the rear cover using a flat screwdriver or another suitable tool.
alarm Low BackupBatt occurs. Follow these instructions:
3. Remove all plug-in modules.4. The battery is located in a holder on the circuit board. Remove the old battery with a small
sharp screwdriver and push with a finger the new battery into the holder. Use only CR1225lithium battery.
5. Put the rear cover back. Use slight pressure to lock the snaps into the housing. Pay attentionthat the cover is in correct position and not upside down!
6. Plug the modules back into the slots.
7. Power the controller on, adjust date and time and check all setpoints.
7/21/2019 IA NT PWR 2.0 Reference Guide
http://slidepdf.com/reader/full/ia-nt-pwr-20-reference-guide 90/92
InteliATSNT PWR, SW version 2.0, ©ComAp – June 2010 90IA-NT- PWR-2.0-Reference Guide.pdf
ta
Inputs/Outputs overview
Technical Da
Model BIN BOUT COM1 COM2GenVoltage
MainsVoltage
Gen.Current
.
IA-NT PWR 7 7 Y* Y* Y Y Y NOTE: * With optional plug-in moduleY -AvailableN -Not available
Power supply
Voltage supply 8-36V DCConsumption 40-430mA depend on supply voltage and
Consumption depends on supply voltage 0,104A at 8VDC
VDC0,044A at 30VDC
36VDC
p-out: 100ms from min. 10V, return to min. 8V
ent tolerance 2 % at 24V
temperature
0,080A at 12VDC0,051A at 24
0,040A at
Allowed supply voltage dro
Battery voltage measuremNOTE: For the supply voltage less than 7V the backlight of the display is switched off.Short-term voltage drops (e.g. during the engine cranking) do not affect the operation at all.
Operating conditions
ing temperature IA-NTOperat -20.+70Storage r
oCtemperatu e oC
Humidity 95% without condensation
EN 61010-1:95 +A1:97Electromagnetic Compatibility EN 50081-1:94, EN 50081-2:96
:99, EN 50082-2:97- 25 Hz, ±1,6mm
25 - 100 Hz, a = 4 gShocks a = 200 m/s2
Dimensions and weight
-30.+80Protection front panel IP65
Standard conformity
Low Voltage Directive
EN 50082-1Vibration 5
Dimensions 180x120x55mmWeight 450g
7/21/2019 IA NT PWR 2.0 Reference Guide
http://slidepdf.com/reader/full/ia-nt-pwr-20-reference-guide 91/92
InteliATSNT PWR, SW version 2.0, ©ComAp – June 2010 91IA-NT- PWR-2.0-Reference Guide.pdf
Mains and generator
Nominal frequency 50-60Hzurement tolerance 0,2Hz
t current (from CT)
se (In=5A) A
ent tolerance 2% from the Nominal current150 A / 1s
ralphase to phase
ral
ase to phase0.6 MΩ phase to phase0.3 MΩ phase to neutral
ent tolerance 2 % from the Nominal voltagess III / 2 (EN61010)
Frequency meas
Current inputsNominal inpu 5 ALoad (CT output impedanc < 0,1 Ω
< 0,2 VA per phae)
CT input burdenMax. measured current from CT 10Current measuremMax. peak current from CTMax. continuous cur 12 Arent
Voltage inputsC phase to neutMeasuring voltage range 0 – 277 VA
0 – 480 VACMaximal measured voltage 340 VAC phase to neut
600 VAC phInput resistance
Voltage measuremOvervoltage cla
Binary inputs and outputs
Binary inputsNumber of inputs 7
4,2 kΩ 36 VDC
Max voltage level for open contact indication 8-36 V
7 A
6 VDC
Input resistanceInput range 0-
Switching voltage level for close contact indication 0-2 V
Binary open collector outputsNumber of outputsMaximum current 0,5Maximum switching voltage 3
IL-NT RS232 interface (optional card)
Plugs into IA-NT controller COMMUNICATION MODULE port.
.4kBd Analog
4520: RS232 to RS422/485 converter, DIN rail, automatic RS485 bussupervision, no external data flow control sign vanic isolated.
Recomm ed internal converter: ADVANTECH – PCL-745B or PCL745S: Dual port RS422/485 Interface card, automatic RS485 bussupervision, no external data flow control signals, galvanic isolated
Maximal distance 10mMaximum Speed Up to 57.6 kBd (DIRECT), 38modem, 9.6 kBd digital modem, 57.6 kBd (MODBUS)
Recommend external converter: ADVANTECH – ADAM
als, gal
end
NOTE: For details on all IA-NT extension and communication modules see IL-NT, IC-NT, IA-NT, ID-Lite- Accessory Modules manual.
7/21/2019 IA NT PWR 2.0 Reference Guide
http://slidepdf.com/reader/full/ia-nt-pwr-20-reference-guide 92/92
IL-NT RS232-485 interface (optional card)
Plugs into IA-NT controller COMMUNICATION MODULE port.
Maximal distance 10m (RS232), 1200m (RS485)
Maximum Speed Up to 57.6 kBd (DIRECT), 38.4kBd AnalogBUS)
d)
modem, 9.6 kBd digital modem, 57.6 kBd (MOD
IL-NT S-USB interface (optional car
Plugs into IA- o M A MODULE port.NT c ntroller COM UNIC TION
Up to 57.6 kBd (DIRECT), 38.4kBd Analogital modem, 57.6 kBd (MODBUS)
Use only shielded A-B USB cables up to 5m length.
USB-LINK CABLE 1.8M – ComAp A-B USB cable.
Maximal distance 5mMaximum Speedmodem, 9.6 kBd dig
Recommend USB cable:
IB-Lite interface (opt ional card)
Plugs into IA-NT controller COMMUNICATION MODULE port.
J45 (10baseT)erature -30..+70oC
oC
IO8 extension module (optional card)
Interface to Ethernet ROperating tempStorage temperature -30..+70
IL-NT B
Technical details:
al nfig inary inputs or outputs.
ts 84.7 kΩ 0-36 VDC
contact indication (Logical 1) < 0.8 VDC
tage level for open contact indication (Logical 0) > 2 VDCi di ti 8 36 VDC
IL-NT BIO8 plugs into the controller’s EXTENSION MODULE port.8 dedicated pins of the plug-in card’s r can be cote min ured as b
Binary inputs
Number of inpuInput resistanceInput rangeVoltage level for close
VolM lt l l f t t