1 © by Walter AG

Tiger�tec® Silver - ISO P GenerationThe Rocket

i-PAC12-1

2 © by Walter AG

Tiger�tec® Silver - ISO P GenerationProduct features

NEW: Aluminiumoxide with optimised microstructure � Increase wear resistance

� Higher cutting speed

NEW: Mechanical post-treatment � Higher toughness

NEW: Microedge-Technology� Longer tool life

NEW: ISO P Geometries� Large chip breaking range

NEW: Ground seating surface after coating

� Process reliability

NEW: Silver flank face� Easy wear detection

3 © by Walter AG

• FP5– Finishing– Steel

• MP3– Medium machining– Long chipping steel

• MP5– Medium machining– Steel in general

• RP5– Roughing– Steel

Tiger�tec® Silver - ISO P GenerationComplete geometry family

January 2012 | VM | Kussmaul

4 © by Walter AGJuly 2011 | VM | Drobniewski | Kußmaul

Tiger�tec® Silver - ISO P GenerationGeometry MP5

Universal, stable three-center curve cutting edge� Suitable from continues to interrupted cuts

Reinforced chip breaker blades in the radius area� Improved chip control for small depth of cut� Increases the tool life / decrease the wear

Open groove on the main cutting edge� Soft cutting also on high depth of cut

5 © by Walter AG

• Medium machining steel in general– Universal geometry for a large range of different steels– Largest chip breaking area of all inserts.– From continuous cutting on bar stock and also machining interrupted cuts.

– Most sold insert for machining steel – first choice.

• Industry– General machining– Job shops– Dealers “love” this insert– … but also used in mass production

• Typical cutting data– ap: 0,8 – 5,0mm– f: 0,20 – 0,60mm

Tiger�tec® Silver - ISO P GenerationApplication area – MP5

6 © by Walter AGJuly 2011 | VM | Drobniewski | Kußmaul

Tiger�tec® Silver - ISO P GenerationGeometry RP5

Stable, positive 3 chamfer� Roughing with low power

consumption

Open, deep and wide chip groove� Low cutting temperature� Reduced wear in comparison with previous

geometries

Wider chamfer in the center region of the main cutting edge� Prevents chipping when machining skins or forged

components

7 © by Walter AG

Tiger�tec® Silver - ISO P GenerationGeometry RP5 1

2

1

2

Additional application area of the RP5 in comparison to the NM9 geometry

January 2012 | VM | Kussmaul

8 © by Walter AG

Version 1 Version 2

Material C45 (680 N/mm²) C45 (680 N/mm²)

Insert: CNMG120408 CNMG120408

Grade: ISO P10 ISO P10

Tool: PCLNL3225M12 PCLNL3225M12

Cutting data:

vc 290 350 [m/min]

f 0,32 0,32 [mm]

ap 2,5 2,5 [mm]

Coolant No No

Vc+20%

Lab test RP5Crater wear / Flank wear

January 2012 | VM | Kussmaul

9 © by Walter AG

Available Tiger�tec® Silver inserts

FP5 MP3 MP5 RP5

NRF NRR

January 2012 | VM | Kussmaul

10 © by Walter AG

Tiger�tec® SilverCNMG / CNMM

January 2012 | VM | Kussmaul

11 © by Walter AG

Tiger�tec® SilverDNMG / DNMM

January 2012 | VM | Kussmaul

12 © by Walter AG

Tiger�tec® SilverSNMG / SNMM

January 2012 | VM | Kussmaul

13 © by Walter AG

Tiger�tec® SilverTNMG / TNMMVNMG

January 2012 | VM | Kussmaul

14 © by Walter AG

Tiger�tec® SilverWNMG / WNMM

January 2012 | VM | Kussmaul