Upload
others
View
2
Download
0
Embed Size (px)
Citation preview
www.huskietools.com 81HydRauliC pumps & punCHes
Phone: 800-860-6170 Fax: 800-345-376782
HydraulicPumps&Punches
Hydraulic PumpsPgs. 84-86
Hydraulic Steel Punch & DiesP. 87
Hydraulic Hand and Foot PumpsP. 83
Remote Control HandleP. 88
Foot SwitchP. 88
Hydraulic HoseP. 89
CouplersP. 89
Huskie Tools AmbassadorBruce Oakes, ForemanCompany: Pike ElectricSouth Carolina
Bruce holds the R-14EF and SH-70M.
www.huskietools.com 83
Features
•Two-StagePumpPistonforRapidAdvance•ExternalPressureAdjustmentfrom4,000- 10,000 psi•CanBeOperatedinAnyPosition•KnobTypeReleaseValve
Specifications
Weight 20 lbs.Length 23”Oil Reservoir 44 cu/in fluid1st Stage .75 in3 per stroke2nd Stage .14 in3 per stroke
FP-70010,000 psi Hydraulic Foot Pump
The HP-700 a portable, tough, hydraulic steel pump that has two speed pumping pistons for rapid advance and an external adjustable pressure setting from 4,000 to 10,000 psi output. An internal oil bladder allows the tool to be used in any position.
Our exclusive replaceable, by-pass cartridge is standard in the HP-700. Field repairs and pressure adjustments can be made in minutes. Use our PG-1 gauge for pressure adjustments.
NOTE: When using any of these high pressure tools, always use 10,000 psi rated non-conductive hose (NC-16 series).
The FP-700 a portable, tough, hydraulic steel pump that has two speed pumping pistons for rapid advance and an external adjustable pressure setting from 4,000 to 10,000 psi output. An internal oil bladder allows these tools to be used in any position.
Our exclusive replaceable, by-pass cartridge is standard in the FP-700. Field repairs and pressure adjustments can be made in minutes. Use our PG-1 gauge for pressure adjustments.
NOTE: When using any of these high pressure tools, always use 10,000 psi rated non-conductive hose (NC-16 series).
HP-70010,000 psi Hydraulic Hand Pump
HydRauliC pumps & punCHes
Features
•Two-StagePumpPistonforRapidAdvance•ExternalPressureAdjustmentfrom4,000- 10,000 psi•CanBeOperatedinAnyPosition•KnobTypeReleaseValve
Specifications
Weight 25 lbs.Length 28”Oil Reservoir 44 in3 fluid1st Stage .75 in3 per stroke2nd Stage .14 in3 per stroke
Phone: 800-860-6170 Fax: 800-345-376784
R-14EF1/2 HP, 10,000 psi Hydraulic Pump
Features
•RemoteOperationAllowsFullOperator Control•AdvanceandHoldFeatureStandard•ManualControlDirectlyonPumpMotor•PressureAdjustmentfrom4,000-10,000psi
Specifications
Weight 34 lbs.Size 7”L x 6”W x 14”HPower Output 1/2 HP-6.5 AmpDelivery @ 200 psi 157 in3/minDelivery @ 10,000 psi 19 in3/minOil Capacity 120 in3 (2 quarts)
R-14EA3/4 HP, 10,000 psi Single Acting Hydraulic Pump
The R-14EF remote operated pump gives the operator complete control. Push buttons permit the user to advance and retract at will. The user is never committed to a full cycle, and can always back off at any time during the advance even under pressure. This feature increases efficiency because cuts and crimps can be adjusted as necessary, simply by stopping the advance or retract mode. A 10-foot remote control cable provides both safety and convenience. The user can set up an operation and then move away from the work site before engaging the tool. An over-ride switch on the pump allows full control at the pump motor. The low amperage of this pump allows it to be used virtually anywhere. The pressure can be easily adjusted between 4,000 and 10,000 psi and determined by using our PG-1 in-line gauge. Consult factory for proper adjusting procedure.
NOTE: When using any of these high pressure tools, always use 10,000 psi rated non-conductive hose (NC-16 series).
The R-14EA is a fully remote controlled, single acting, 10,000 psi, electric pump. The two button hand control allows the user to advance, hold, or release at any time. When 10,000 psi is reached, the pump will automatically shut off and hold until the operator pushes the release button to retract the tool. There is an auto cycle switch that allows the operator to push the advance button and the pump will automatically advance, run to 10,000 psi and release. This feature is mostly used for production crimping and cutting where the operator must have the freedom of both hands. A remote foot control pedal is optional.
NOTE: When using any of these high pressure tools, always use 10,000 psi rated non-conductive hose (NC-16 series).
HydRauliC pumps & punCHes
Features
•RemoteOperationAllowsFullOperatorControl•ManualandAutomaticModeforAdditional Versatility•3/4HPRating•LowAmperageRequirement
Optional Accessories
REC-P1CASE Steel Carrying Case, p. 94URH-14 Remote Control Handle,
p. 88FS-14 FootSwitch,p.88
Optional Accessories
URH-14 Remote Control Handle, p. 88
FS-14 FootSwitch,p.88
Specifications
Weight 75 lbs. with OilSize 14”L x 13.25”W x 16”HPower Output 3/4 HP - 8.2 AmpDelivery @ 300 psi 157 in3/minDelivery @10,000 psi 36 in3/minOil Capacity 182 cu/in (3 quarts)
www.huskietools.com 85
Features
•RemoteOperationAllowsFullOperator Control•ManualandAutomaticModeforAdditional Versatility•LowAmperageRequirement
Specifications
Weight 75 lbs. with OilSize 14”L x 13.25”W x 16”HPower Output 3/4 HP - 8.2 AmpDelivery @ 300 psi 157 in3/minDelivery @10,000 psi 36 in3/minOil Capacity 182 cu/in (3 quarts)
HPG-44 HP, Gas Engine 10,000 psi Hydraulic Pump
The R-14EAD is a fully remote controlled, double acting, 10,000 psi, electric pump. The hand control allows the user to advance or release at any time. There is an auto cycle switch that allows the operator to push the advance button and the pump will automatically advance, run to 10,000 psi and release. This feature is used mostly for production crimping and cutting, where the operator must have the freedom of both hands. A remote foot control pedal is optional.
NOTE: When using any of these high pressure tools, always use 10,000 psi rated non-conductive hose (NC-16 series).
The HPG-4 is a self-contained high pressure pump, with manual operation. It is equipped with a 4 HP Briggs & Stratton engine. A four-way valve controls the hydraulic fluid direction for the advance and retract modes. One double acting tool can be operated or two single acting tools at one time. Connection to one port for single acting tools will work since the control valve will dump the fluid when shifted to the retract position. The pump is very compact and comes with carrying handles.
NOTE: When using any of these high pressure tools, always use 10,000 psi rated non-conductive hose (NC-16 series).
R-14EAD3/4 HP, 10,000 psi Double Acting Hydraulic Pump
HydRauliC pumps & punCHes
Features
•FourWayValveAllowsforSingleorDouble Acting Capacity•StandardScrewTypeMaleandFemale Couplers
Specifications
Weight 74 lbs. with OilOil Capacity 5 GallonsGas Tank 3 PintsMax Pressure 10,000 psiPower Output 4 HPOil Delivery @ 100 psi
480 in3/min
Oil Delivery @ 10,000 psi
55 in3/min
Optional Accessories
FS-14 FootSwitch,p.88
RC-5Optional Roll/
Carry Cage
Phone: 800-860-6170 Fax: 800-345-376786
The Huskie REC-P1 is a 28.8 volt, battery operated hydraulic pump that runs on two 14.4 Volt Huskie BP-80 series batteries. The REC-P1 is supplied with a push button remote control that allows the operator to advance, hold, and retract when needed. The user is never committed to a full cycle and can always back off at any time during the advance– even when the pump is under pressure. High pressure, non-conductive hose can be attached to a 360° moveable swivel port on the pump. This swivel port allows the user to position the hose to fit in confined aerial buckets and manholes.
Both batteries must be inserted in the pump to operate. It is recommended to operate the pump with a 10 foot hose, up to a maximum of 20 feet. A longer hose will cause cycle times to increase.
We recommend you specify the Huskie SC-Series flush face dripless couplers, as not to deplete the oil in the reservoir when changing heads.
For additional ordering information, please refer to page 10.
REC-P1ROBO*PUMP10,000 psi Battery Powered 28.8 Volt Pump
HydRauliC pumps & punCHes
Features
•Powerful28.8Volt•OperateUptoSingleActing60TonPress•Adjustable10,000psi•EliminatestheNeedforACPower•CompactandPortable
Specifications
Output 10,000 psiWeight 23 lbs. with 2 BatteriesSize 16”L x 6”H x 10”D
Crimping Estimates
2 BP-80Using a 10 ft. HoseandEP-60Won1272 ACSR
12
No Load Cycle Time
Advance 25 Sec., Retract 30 Sec.
Optional Accessories
FS-14 FootSwitch,p.88URH-14 Remote Handle, p. 88REC-P1CASE Steel Carrying Case, p. 94
www.huskietools.com 87
The portable SH-270M punch was designed to punch holes through 1/2” mild steel, aluminum and copper. The punched hole size is 1/16” larger than your bolt size. A stripper guide extends on either side of the ram to strip the material after punching. This hand-held unit will operate from any 10,000 psi hydraulic pumping source.
Some uses include the punching of bus bars, tower iron, railing, I-beams and truck frames. Custom size punch and dies are available upon request. Oval and square sizes are also available. Consult factory for order information. The SH-270M and SH-270F comes complete with four sets of punch and die sizes for 3/8”, 1/2”, 5/8” and 3/4” bolts and carrying case.
NOTE: USE ONLY 10,000 psi RATED HOSE.
SH-270M35 Ton Hydraulic Steel Punch
Features•PunchesUPto1/2”MildSteel•13/16”MaxHoldDiameter•WillPunch:Oval,Round,Square,andSlotted Holes•CustomSizesAvailable•Operatesfroma10,00psiPumpSource
Specifications
Output 35 TonWeight 28 lbs.Capacity 1/2” Thick Mild SteelMax. Hole 13/16” DiameterDimensions 14” x 8” x 3.5”Throat Depth 2.75”
Order Data
SH-70M Steel Punch with Male Coupler
SH-70F SteelPunchwithFemaleCoupler
HydRauliC pumps & punCHes
Round DiesITEM DESCRIPTION BOLT SIZE
SHD-18 1/8”Punch&DieSetSHD-316 3/16”Punch&DieSetSHD-14 1/4”Punch&DieSetSHD-932 9/32”Punch&DieSetSHD-516 5/16”Punch&DieSetSHD-38 3/8”Punch&DieSetSHD-716 7/16”Punch&DieSet10.5 3/8”SHD-12 1/2”Punch&DieSetSHD-916 9/16”Punch&DieSet13.5 1/2”SHD-58 5/8”Punch&DieSetSHD-1116 11/16”Punch&DieSet17.5” 5/8”SHD-34 3/4”Punch&DieSetSHD-1316 13/16”Punch&DieSet20.5 3/4”
Oblong DiesITEM DESCRIPTION BOLT SIZE
SHD-516X1316 5/16”X13/16”OblongPunch&DieSetSHD-38X1316 3/8”X13/16”OblongPunch&DieSetSHD-716X1316 7/16”X13/16”OblongPunch&DieSet 3/8”SHD-12X38 1/2”X3/8”OblongPunch&DieSetSHD-12X34 1/2”X3/4”OblongPunch&DieSetSHD-12X1316 1/2”X13/16”OblongPunch&DieSetSHD-916X34 9/16”X3/4”OblongPunch&DieSet 1/2”SHD-916X1316 9/16”X13/16”OblongPunch&DieSet 1/2”SHD-58X1316 5/8”X13/16”OblongPunch&DieSetSHD-1116X1316 11/16”X13/16”OblongPunch&DieSet 5/8”SHD-34X1316 3/4”X13/16”OblongPunch&DieSet
Square DiesITEM DESCRIPTION
SHD-14SQ 1/4”SquarePunch&DieSetSHD-38SQ 3/8”SquarePunch&DieSetSHD-716SQ 7/16”SquarePunch&DieSetSHD-12SQ 1/2”SquarePunch&DieSetSHD-1732SQ 17/32”SquarePunch&DieSetSHD-916SQ 9/16”SquarePunch&DieSet
Hex DiesITEM DESCRIPTION
SHD-716HEX 7/16”HexPunch&DieSetSHD-916HEX 9/16”HexPunch&DieSetSHD-1116HEX 11/16”HexPunch&DieSetSHD-1316HEX 13/16”HexPunch&DieSet
Phone: 800-860-6170 Fax: 800-345-376788
URH-14Remote Control Handle
Features
•ForUsewithAllElectricalandBattery Operated Single Acting Pumps•AllowsOperatorOneHandControlattheTool Head•10FootCord
Specifications
Weight 3 lbs.Size 8”L x 1.5”W x 6.5”H
FS-14Foot Switch
The URH-14 remote control handle is for use with the R-14EF, R-14EA and REC-P1 pumps. It is equipped with a standard 3/8” high pressure coupler that can be easily matched to your existing tool head. A 10 foot, three wire control cable can be hooked directly to the R-14EF or hard wired to any pump that has similar remote control features. The URH-14 weighs only three pounds and is made of tough, durable, molded plastic with a double insulated on/off switch.
The FS-14 was designed to replace our pendant hand control on pump models R-14EF, R-14EA, R-14EAD and REC-P1. This foot control allows the operator to free his hands for better control of his work load. It has a green pedal for the advance mode and a red pedal for the retract mode. The FS-14 is mostly used in work bench applications.
HydRauliC pumps & punCHes
Features
•ForUsewithAllElectricalandBatteryOperated Single Acting Pumps•AllowsOperator“HandsFree”Controlof Advance and Retract Pump Mode•10FootCord
Specifications
Weight 4.2 lbs.Size 9.5”L x 7”W x 3”H
Order Data
URH-14 Remote Control HandleREC-URH Remote Control Handle
forREC-P1
Optional Accessories
URH-14 Remote Control HandleFS-14 FootSwitch
www.huskietools.com 89
Features
•HighlyVisibleSafetyOrange(RB-1610isBrown)•HeavyDutyShrinkWrapatHoseEndsfor Reduced Risk of Leaking•DateCodedatPointofAssembly
Order Data
NC-1606 3/16” x 6’NC-1610 3/16” x 10’RB-1610 3/16” x 10’ (Rubber Bound)NC-1615 3/16” x 15’NC-1620 3/16” x 20’NC-1625 3/16” x 25’NC-450 1/3” x 50’ (1/4” NPT
StandardEnds)3/8” NPT hose ends standard. 1/4” NPT also available. Any combination of high pressure couplers are available. Simply specify the kind you require when ordering.
Our high pressure, non-conductive NC-SERIES hoses and couplers are rated at 10,000 psi working pressure. The hose ends are covered with a thick clear jacket of heavy duty shrink wrap to reduce the risk of hose bursts at these points. They are also date coded during assembly. As a result of injuries sustained by operators of hydraulic products via broken or damaged high pressure hoses Huskie has developed a replacement hose improvement program for our customers. Consult your representative for information. Our hoses come standard with 3/8” male/female couplers.
NOTE: FOR OPERATOR SAFETY WE RECOMMEND HOSE REPLACEMENT AFTER 3 YEARS.
NC-SERIES10,000 psi High Pressure Hydraulic Hose
HydRauliC pumps & punCHes
SC-SERIES10,000 psi High Pressure Flush Face Couplers
Features
•10,000psiOperatingPressureMarkedon Both Halves•SimpleQuickConnectandDisconnect•TwistSleeveLocktoPreventAccidentalDisconnect•FlushFace,NON-DRIPValving,BothHalves
Specifications
HoseEnd 3/8” NPTThreadedEnd 3/8” NPTWorking Pressure 10,000 psiMinimum Burst PressureCoupled 34,800 psiUncoupled 29,000 psiHand Connection 250 psi at 150 lbs.FluidLossPerDisconnection
.035 ml
The SC-SERIES are flush face, snap-type couplers for use in high pressure applications. They are not interchangeable with low pressure flush face couplers. Positive connect or disconnect prevents tool failure due to partial coupled halves of conventional screw-type couplers.
Order Data
SCF-8F FemaleHalfwithFemalePortSCF-8 FemaleHalfwithMaleEndSCM-8 MaleHalfwithFemalePortFC-8F FemaleHalfwithFemalePortFC-8 FemaleHalfwithMalePortDC-SCF FemaleCap
FC-8F
SCF-8FSCF-8
SCM-8
SCM-8
Phone: 800-860-6170 Fax: 800-345-376790
Hydraulic Oil
Huskie Tools offers replacement Hydraulic Oil in three sizes for any service needs. It is our own MV-32 clear hydraulic fluid and can be used in all of our hydraulic products. This fluid can also be added to other clear hydraulic fluids for filling or topping off a hydraulic circuit. Do not mix with other red or blue colored hydraulic fluids as this will “gel” and cause the tool or pump to malfunction. A complete MSDS is available from Huskie Tools upon request.
HydRauliC pumps & punCHes
Order Data
HF-5G 5 Gallon ContainerHF-1G Gallon ContainerHF-1Q Quart ContainerHF-5GRED RedHydraulicFluidforLow
TemperaturesHF-1GRED RedHydraulicFluid1GallonHG-1QRED RedHydraulicFluidQuart