84
2011 05H.EA364 HYDRAULIC CRAWLER CRANE SCX3500-3 Stage III A / Tier 3

HYDRAULIC CRAWLER CRANE · SCX3500-3 SPECIFICATIONS Specifications Model CUMMINS QSL9 Type 4-cycle, water-cooled,Direct-injection,Turbo-charger Diesel engine Displacement 8.9 Liters

  • Upload
    others

  • View
    10

  • Download
    0

Embed Size (px)

Citation preview

Page 1: HYDRAULIC CRAWLER CRANE · SCX3500-3 SPECIFICATIONS Specifications Model CUMMINS QSL9 Type 4-cycle, water-cooled,Direct-injection,Turbo-charger Diesel engine Displacement 8.9 Liters

2011 05H.EA364

HYDRAULIC CRAWLER CRANE

SCX3500-3Stage III A / Tier 3

Page 2: HYDRAULIC CRAWLER CRANE · SCX3500-3 SPECIFICATIONS Specifications Model CUMMINS QSL9 Type 4-cycle, water-cooled,Direct-injection,Turbo-charger Diesel engine Displacement 8.9 Liters

2

VARIATIONSCX3500-3

Variation of The Attachment

SCX3500-3

Boom Length m 24 to 72

Ground Contact Pressure kPa (kgf/cm²)

144 (1.47)(100t + 15t hook

attached)Overall Operating Weight t Approximately 341

Boom Length m 18

Ground Contact Pressure kPa (kgf/cm²) 136 (1.39)

(with 350t hook)

Overall Operating Weight t Approximately 321

Hammer Head Specification

Boom Length m 24 to 72

Ground Contact Pressure kPa (kgf/cm²)

144 (1.47)(100t + 15t hook

attached)Overall Operating Weight t Approximately 341

Line Speed *

Front (W1)/Rear (W2)

m/min

110

Boom Hoist (W3) 34 x 2

Tower Jib Hoist (W4) 55

Swing Speed min-1 (rpm) 0.86 (0.86)Travel Speed High / Low km/h 0.9/0.45Gradeability % (Degree) 30 (17)

Engine Model CUMMINS QSL9(Stage III A/Tier 3)

Engine Rated Output Power kW/min-1

(ps/rpm)280/2,000

(380/2,000)

Note : Speeds marked with "*" may vary depending on load applied.

Crane Specification Boom Longest Length with

Aux. Sheave (Rear end Radius: Standard)

Crane Specification Boom Longest Length with

Aux. Sheave (Rear end Radius: Short)

Page 3: HYDRAULIC CRAWLER CRANE · SCX3500-3 SPECIFICATIONS Specifications Model CUMMINS QSL9 Type 4-cycle, water-cooled,Direct-injection,Turbo-charger Diesel engine Displacement 8.9 Liters

3

VARIATION SCX3500-3

SCX3500-3

Tower Length m 24 to 60Tower Jib Length m 24 to 60Tower + Tower Jib Longest Length m 60 + 60

Ground Contact Pressure kPa (kgf/m²)

152 (1.55)(100t + 15t hook

attached)Overall Operating Weight t Approximately 360

Tower Length m 24 to 54Tower Jib Length m 24 to 60Tower + Tower Jib Longest Length m 54 + 60

Ground Contact Pressure

kPa (kgf/cm²)

151 (1.54)(100t + 15t hook

attached)Overall Operating Weight t Approximately 357

Tower Specification Tower with Tower Jib

Longest Length (Rear end Radius: Standard)

Tower Specification Tower with Tower Jib

Longest Length (Rear end Radius: Short)

Boom Length m 24 to 72Crane Jib Length m 13 to 37Boom + Crane Jib Longest Length m 72 + 37

Ground Contact Pressure kPa (kgf/m²)

146 (1.49)(100t + 15t hook

attached)Overall Operating Weight t Approximately 345

Crane Specification Boom with Crane Jib

Longest Length (Rear end Radius: Standard)

Page 4: HYDRAULIC CRAWLER CRANE · SCX3500-3 SPECIFICATIONS Specifications Model CUMMINS QSL9 Type 4-cycle, water-cooled,Direct-injection,Turbo-charger Diesel engine Displacement 8.9 Liters

4

CONTENTSSCX3500-3

Variation of The Attachment 2

Specifications 6

Crane Specifications 7

Dimensions and Specifications ................................................................................................................7Boom Standard Configurations ................................................................................................................8Combination of Boom and Crane Jib (Offset Angle 10° and 30°) ..........................................................9Lowerable Boom Hook Mass ..................................................................................................................10Lowerable Crane Jib Hook Mass ............................................................................................................10Working Ranges ....................................................................................................................................... 11

■Main Boom (Rear end Radius: Standard) ..............................................................................................................11

■Aux. Sheave (Rear end Radius: Standard) ........................................................................................................... 12

■Main Boom with Aux. Sheave (Rear end Radius: Standard) ................................................................................ 13

■Main Boom (Rear end Radius: Short) ................................................................................................................... 14

■Aux. Sheave (Rear end Radius: Short) ................................................................................................................. 15

■Main Boom with Aux. Sheave (Rear end Radius: Short) ...................................................................................... 16

■Crane Jib (Rear end Radius: Standard) ................................................................................................................ 17

■Main Boom with Crane Jib (Rear end Radius: Standard) ..................................................................................... 18

Gross Rated Load Table ..........................................................................................................................19■Main Boom (Rear end Radius: Standard) ............................................................................................................. 19

■Aux. Sheave (Rear end Radius: Standard) ........................................................................................................... 20

■Main Boom with Aux. Sheave (Rear end Radius: Standard) ................................................................................ 21

■Main Boom (Rear end Radius: Short) ................................................................................................................... 22

■Aux. Sheave (Rear end Radius: Short) ................................................................................................................. 23

■Main Boom with Aux. Sheave (Rear end Radius: Short) ...................................................................................... 24

■Crane Jib (Rear end Radius: Standard) ................................................................................................................ 25

■Main Boom with Crane Jib (Rear end Radius: Standard) ..................................................................................... 33

Tower Specifications 39

Dimensions and Specifications ..............................................................................................................39Tower Standard Configurations ..............................................................................................................40Restriction of Hook Usage .....................................................................................................................41Lowerable Jib Hook Mass ......................................................................................................................42Lowerable Tower Head Hook Mass .......................................................................................................42

VARIATION

SPECIFICATIONS

Page 5: HYDRAULIC CRAWLER CRANE · SCX3500-3 SPECIFICATIONS Specifications Model CUMMINS QSL9 Type 4-cycle, water-cooled,Direct-injection,Turbo-charger Diesel engine Displacement 8.9 Liters

5

CONTENTS SCX3500-3

Working Ranges .......................................................................................................................................43■Rear end Radius: Standard .................................................................................................................................. 43

■Rear end Radius: Short ........................................................................................................................................ 44

■Tower Head Hoisting (Rear end Radius: Standard) .............................................................................................. 45

Gross Rated Load Table ..........................................................................................................................46■Tower 24 m (Rear end Radius: Standard) ............................................................................................................ 46

■Tower 30 m (Rear end Radius: Standard) ............................................................................................................ 48

■Tower 36 m (Rear end Radius: Standard) ............................................................................................................ 50

■Tower 42 m (Rear end Radius: Standard) ............................................................................................................ 52

■Tower 48 m (Rear end Radius: Standard) ............................................................................................................ 54

■Tower 54 m (Rear end Radius: Standard) ............................................................................................................ 56

■Tower 60 m (Rear end Radius: Standard) ............................................................................................................ 58

■Tower 24 m (Rear end Radius: Short) .................................................................................................................. 60

■Tower 30 m (Rear end Radius: Short) .................................................................................................................. 62

■Tower 36 m (Rear end Radius: Short) .................................................................................................................. 64

■Tower 42 m (Rear end Radius: Short) .................................................................................................................. 66

■Tower 48 m (Rear end Radius: Short) .................................................................................................................. 68

■Tower 54 m (Rear end Radius: Short) .................................................................................................................. 70

■Tower 24m Tower Head Hoisting (Rear end Radius: Standard) ........................................................................... 72

■Tower 30m Tower Head Hoisting (Rear end Radius: Standard) ........................................................................... 73

■Tower 36m Tower Head Hoisting (Rear end Radius: Standard) ........................................................................... 73

■Tower 42m Tower Head Hoisting (Rear end Radius: Standard) ........................................................................... 73

■Tower 48m Tower Head Hoisting (Rear end Radius: Standard) ........................................................................... 74

■Tower 54m Tower Head Hoisting (Rear end Radius: Standard) ........................................................................... 74

■Tower 60m Tower Head Hoisting (Rear end Radius: Standard) ........................................................................... 74

TECHNICAL DATA

Weights and Dimensions of Disassembled Units 75

Weights and Dimensions List .................................................................................................................75

Equipment List 80

Standard and Optional Equipment .........................................................................................................80

Page 6: HYDRAULIC CRAWLER CRANE · SCX3500-3 SPECIFICATIONS Specifications Model CUMMINS QSL9 Type 4-cycle, water-cooled,Direct-injection,Turbo-charger Diesel engine Displacement 8.9 Liters

6

Specifications

SPECIFICATIONSSCX3500-3

Specifications

Model CUMMINS QSL9Type 4-cycle, water-cooled,Direct-injection,Turbo-charger

Diesel engineDisplacement 8.9 LitersRated Output 280 kW / 2,000 min-1 (380 PS / 2,000 rpm)Fuel Tank Capacity 550 LitersNotes Engine meets Tier 3 / Stage III A of engine exhaust gas

emission regulations.Engine rated horsepower is based on international ratingformula that includes engine alternator and without fan.

Engine

Control System

Main actuators are controlled by hydraulic pilot system. Working speeds can be precisely controlled by lever stroke and volume dial.Safety devices are securely operated by combined various electronic controls with hydraulic system.

Control Levers Designed and layout on ergonomics. Arm chair lever type is standard.

Display Panel Design 8 inches size. Located to check working state easily without disturbing the view of the operator.

Control

Hydraulic Tank 350 Liters

Hydraulic Pump Capacity

Maximum pressure 31.4 MPa

P1 320 l / min W3,W4 winch, Travel (R)

P2 320 l / min W1,W2 winch, Travel(L), Quick draw

P3 158 l / min Swing, Reeving winch, Cylinders

P4 74 l / min Fan drive(Radiator, Oil cooler)

P5 44 l / min Pilot

Hydraulic System

Winch

0.86 rpm3 sets of hydraulic motor with wet multiple disc brake + planetary reduction gears and turn table bearing with external teeth.Precise swing operation is possible by swing brake with pedal.

Swing Device

Easy assembly for front attachments.Crawler sideframe self assembly is possible by Quick draw(Opt).By using Quick draw system, assembly work can be done by helper crane to install 19.7 ton base counter weight.

Mast

Counter WeightTotal Weight 145.0 tBase Weight 19.7 t × 1Weight 8.95 t × 14

Lower WeightTotal Weight 25.0 tWeight 12.5 t × 2

Counter Weight

High tensile steel box structureJack up devicePin connection with crawler sideframe by hook on system

 

Carbody

Crawler SideframeHigh tensile steel box structureWith travel device and pin connection and connection cylinders

Shoe 1250mm flat shoe

Upper Roller7 pieces for each sideDouble flange type 2 cantilever type 5

Lower Roller

15 pieces for each sideDouble flange type with plane bearing and floating seal for lifetime lubricationForging and heat treated steel

Travel Device

1unit for each sideHydraulic motor with wet multiple disc brake + Planetary reduction gears

Travel speed High:0.9 km/hr.

Lower:0.45 km/hr.Gradablity 30 %

Crawler Sideframe

W1(Front)

W2(Rear)

W3(Hoist)

W4(Jib Hoist)

Rope Diameter 28 mm 28 mm 28 mm 28 mmRope Length 335 m 610 m 490 m 370 mRope Speed 110m/min 110m/minRated Linepull 147 kN 147 kN(1st layer) (230 kN) (230 kN)

High speed lifting and lowering is possible by ECO mode with low engine speed under light load.Hydraulic motor with wet multiple disc brake and planetary reduction gears inside of winch drum.

 

Page 7: HYDRAULIC CRAWLER CRANE · SCX3500-3 SPECIFICATIONS Specifications Model CUMMINS QSL9 Type 4-cycle, water-cooled,Direct-injection,Turbo-charger Diesel engine Displacement 8.9 Liters

7

Crane SpecificationsDimensions and Specifications

SPECIFICATIONS SCX3500-3

Dimensions and Specifications

7120

R4825

9265 1250

175038

30

550

940

2470

2990

1495

3150

2400

0 to 7

2000

83.5°

15008640

R9000

1930

3510

10440R6800R8300

8750 

R680

0Re

ar E

nd

Swing

Ra

dius

Rear end Radius:ShortRear end Radius:Standard

Crane SpecificationsMax. Lifting Load × Working Radius(Boom top attached) t × m 180 × 5.9

Max. Lifting Load × Working Radius(Hammer head attached) t × m 350 × 5.0

Basic Boom Length (Boom top attached) m 24Max. Boom Length (Boom top attached) m 72Basic Boom Length (Hammer head attached) m 18Crane Jib Length m 13 to 37Max. Boom with Crane Jib Length m 72 + 37Ground Contact Pressure (Boom top attached) kPa (kgf/cm²) 135 (1.38)

(24m Boom with 180 t Hook)Ground Contact Pressure (Hammer head attached) kPa (kgf/cm²) 136 (1.39)

(18m Boom with 350 t Hook)Overall Operating Weight(Boom top attached) t Approximately 320

(24m Boom with 180 t Hook)Overall Operating Weight (Hammer head attached) t Approximately 321

(18m Boom with 350 t Hook)

Hook Mass350 t 4,440 kg180 t 3,340 kg100 t 3,110 kg45 t 2,170 kg15 t 620 kg

Number of Front/Rear Winch Rope and Lifting Load

Hook CapacityMaximum Rated Load (ton)

13 falls 12 falls 11 falls 10 falls 9 falls 8 falls 7 falls 6 falls 5 falls 4 falls 3 falls 2 falls 1 fall180 t 180 170 157 144 131 118 104 90 76 61 - - -100 t - - - - - - 100 90 76 61 46 31 -45 t - - - - - - - - - - 45 31 -15 t - - - - - - - - - - - - 15

Crane Specifications

NOTE : Data is expressed in SI units followed by conventional units in ( ).

Page 8: HYDRAULIC CRAWLER CRANE · SCX3500-3 SPECIFICATIONS Specifications Model CUMMINS QSL9 Type 4-cycle, water-cooled,Direct-injection,Turbo-charger Diesel engine Displacement 8.9 Liters

8

SpecificationsBoom Standard Configurations

SPECIFICATIONSSCX3500-3

Dimensions Not Shown In The Figure

Symbols Boom Length (m) Note

HB9.5 9.5 Boom BaseHH1.5 1.5 Hammer HeadHT1.5 1.5 Boom Top

H6 6 Boom InsertH6B 6 Boom Insert BH9 9 Boom Insert

HR7 7 Reducer

Boom Standard Configurations

Aux. Sheave Installable Boom LengthBoom Length (m) 18 24 30 36 42 48 54 60 66 72With Aux. Sheave

( : Attachable : Not Attachable )

BoomBoom Length

(m) Boom Configurations

18HB9.5 HR7

7

HH1.5

3.02.5

24HB9.5 HR7

7 6

H6B HT1.5

3.02.5

30HB9.5 HR7

7 6

H6B HT1.5H6

63.02.5

36HB9.5 HR7

7 6

H6B HT1.5H6

6

H6

63.02.5

42HB9.5 HR7

7 699

H6BH9 H9 HT1.5

3.02.5

48HB9.5 HR7 H6

7 6 699

H6BH9 H9 HT1.5

3.02.5

54HB9.5 HR7 H6

7 6 699

H6

6

H6BH9 H9 HT1.5

3.02.5

60HB9.5 HR7

7 699

H6BH9 H9 HT1.5HB9.5 HR7

7 699

H6BH9 H9

HB9.5 HR7

7 69999

H6BH9 H9 H9 H9 HT1.5

6

H6

6

H6

6

H6

3.02.5

3.02.5

66HB9.5 HR7 H6

7 6 69999

H6BH9 H9 H9 H9 HT1.5

3.02.5

72HB9.5 HR7 H6

7 6 6 69999

H6 H6BH9 H9 H9 H9 HT1.5

3.02.5

Crane Specification Boom

Page 9: HYDRAULIC CRAWLER CRANE · SCX3500-3 SPECIFICATIONS Specifications Model CUMMINS QSL9 Type 4-cycle, water-cooled,Direct-injection,Turbo-charger Diesel engine Displacement 8.9 Liters

9

SpecificationsCombination of Boom and Crane Jib (Offset Angle 10° and 30°)

SPECIFICATIONS SCX3500-3

Crane Jib (Offset Angle 10° and 30°)Crane Jib Length (m) Offset Angle Crane Jib Configurations

13

10°

5.85

6.56.5

5.857.8

30°

5.85

6.56.5

5.857.81.65

19

10°

5.85

6 6.56.5

5.857.85.85

30°

5.85

6 6.56.5

5.857.81.65

5.85

25

10°

5.85

6 6 6.56.5

5.857.8 5.855.85

30°

6 6 6.56.5

5.855.857.8

1.65

5.855.85

31

10°

5.85

6 6 6 6.56.5

5.857.8 5.85

5.85 5.85

30°

5.855.85

7.81.65

5.855.85

5.85

6 6 6 6.56.5

37 10°

5.85

6 6 66.5

5.857.8 5.85 5.85 5.85

6 6.5

5.85

Combination of Boom and Crane Jib (Offset Angle 10° and 30°)

Combination of Boom and Crane Jib

Crane Jib Length (m)

13 19 25 31 37Offsetangle10°

Offsetangle30°

Offsetangle10°

Offsetangle30°

Offsetangle10°

Offsetangle30°

Offsetangle10°

Offsetangle30°

Offsetangle10°

Offsetangle30°

Boom Length (m

)

243036424854 606672

( : Attachable : Not Attachable )

Page 10: HYDRAULIC CRAWLER CRANE · SCX3500-3 SPECIFICATIONS Specifications Model CUMMINS QSL9 Type 4-cycle, water-cooled,Direct-injection,Turbo-charger Diesel engine Displacement 8.9 Liters

10

SpecificationsLowerable Boom Hook Mass

SPECIFICATIONSSCX3500-3

Lowerable Boom Hook Mass

Boom Length (m)No. of Reeved Lines

1 fall 2 falls 3 falls 4 falls 5 falls 6 falls 7 falls 8 falls 9 falls 10 falls 11 falls 12 falls 13 falls24 0.6 2.1 2.1 3.1 3.1 3.1 3.1 3.3 3.3 3.3 3.3 3.3 3.330 0.6 2.1 2.1 3.1 3.1 3.1 3.1 3.3 3.3 3.3 3.3 3.3 3.336 0.6 2.1 2.1 3.1 3.1 3.1 3.1 3.3 3.3 3.3 3.3 3.3 3.342 0.6 2.1 2.1 3.1 3.1 3.1 3.1 3.3 3.3 3.3 3.3 3.3 -48 0.6 2.1 2.1 3.1 3.1 3.1 3.1 3.3 3.3 3.3 3.4 - -54 0.6 2.1 2.1 3.1 3.1 3.1 3.1 3.3 3.3 - - - -60 0.6 2.1 2.1 3.1 3.1 3.1 3.1 3.3 - - - - -66 0.6 2.1 2.1 3.1 3.1 3.1 3.1 - - - - - -72 0.6 2.1 2.1 3.1 3.1 3.1 3.2 - - - - - -

Unit:ton

Dimensions Not Shown In The Figure

Symbols Jib Length (m) Note

6.5 6.5 Jib top, jib base6 6 Jib insert

Jib Pendant Rope

Symbols Length (m) Rope Diameter (mm) Imprint

7.8 7.8 35.5 □・△・ 35.5 ・ 7.8・ S5.85 5.85 32 □・△・ 32 ・ 5.85 ・ S 1.65 1.65 32 □・△・ 32 ・ 1.65 ・ S

Determine the jib pendant rope from the rope caulk mark.

Imprint

Boom Length + Jib Length (m)

No. of Reeved Lines1 fall 2 falls

55 0.6 2.161 0.6 2.167 0.6 2.173 0.6 2.179 0.6 2.185 0.6 2.191 0.6 2.197 0.6 2.1103 0.6 -109 0.6 -

Unit:ton

Lowerable Crane Jib Hook Mass

Page 11: HYDRAULIC CRAWLER CRANE · SCX3500-3 SPECIFICATIONS Specifications Model CUMMINS QSL9 Type 4-cycle, water-cooled,Direct-injection,Turbo-charger Diesel engine Displacement 8.9 Liters

11

SpecificationsWorking Ranges

SPECIFICATIONS SCX3500-3

■Main Boom (Rear end Radius: Standard)

5

10

15

20

25

30

35

40

45

50

55

60

65

5 10 15 20 25 30 35 40 45 500 70656055

80

75

70

1.5m

3.15

m

30°

83.5°

72m

30m

24m

66m

60m

54m

48m

42m

36m 

6.0m

5.8m

5.6m

Maximum Boom Angle

Minimum Boom Angle

180 t Hook 100 t Hook 45 t Hook

Working Radius (m)

Height Above G

round

(m)

Working Ranges

Page 12: HYDRAULIC CRAWLER CRANE · SCX3500-3 SPECIFICATIONS Specifications Model CUMMINS QSL9 Type 4-cycle, water-cooled,Direct-injection,Turbo-charger Diesel engine Displacement 8.9 Liters

12

SpecificationsWorking Ranges

SPECIFICATIONSSCX3500-3

■Aux. Sheave (Rear end Radius: Standard)

5

10

15

20

25

30

35

40

45

50

55

60

65

5 10 15 20 25 30 35 40 45 500 70656055

80

75

70

1.5m

3.15

m

30°

83.5°

30m

24m

72m

66m

60m

54m

48m

42m

36m 

4.4m

Working Radius (m)

15 t Hook

Height Above G

round(m)

Maximum Boom Angle

Minimum Boom Angle

Page 13: HYDRAULIC CRAWLER CRANE · SCX3500-3 SPECIFICATIONS Specifications Model CUMMINS QSL9 Type 4-cycle, water-cooled,Direct-injection,Turbo-charger Diesel engine Displacement 8.9 Liters

13

SpecificationsWorking Ranges

SPECIFICATIONS SCX3500-3

■Main Boom with Aux. Sheave (Rear end Radius: Standard)

5

10

15

20

25

30

35

40

45

50

55

60

65

5 10 15 20 25 30 35 40 45 500 70656055

80

75

70

1.5m

3.15

m

30°

83.5°

30m

24m

72m

66m

60m

54m

48m

42m

36m 

6.0m

5.8m

5.6m

Working Radius (m)

180 t Hook 45 t Hook100 t Hook

Height Above G

round(m)

Maximum Boom Angle

Minimum Boom Angle

Page 14: HYDRAULIC CRAWLER CRANE · SCX3500-3 SPECIFICATIONS Specifications Model CUMMINS QSL9 Type 4-cycle, water-cooled,Direct-injection,Turbo-charger Diesel engine Displacement 8.9 Liters

14

SpecificationsWorking Ranges

SPECIFICATIONSSCX3500-3

■Main Boom (Rear end Radius: Short)

5

10

15

20

25

30

35

40

45

50

55

60

65

5 10 15 20 25 30 35 40 45 500 70656055

80

75

70

1.5m

3.15

m

30°

83.5°

30m

24m

72m

66m

60m

54m

48m

42m

36m 

6.0m

5.8m

5.6m

Working Radius (m)

180 t Hook 45 t Hook100 t Hook

Height Above G

round(m)

Maximum Boom Angle

Minimum Boom Angle

Page 15: HYDRAULIC CRAWLER CRANE · SCX3500-3 SPECIFICATIONS Specifications Model CUMMINS QSL9 Type 4-cycle, water-cooled,Direct-injection,Turbo-charger Diesel engine Displacement 8.9 Liters

15

SpecificationsWorking Ranges

SPECIFICATIONS SCX3500-3

■Aux. Sheave (Rear end Radius: Short)

5

10

15

20

25

30

35

40

45

50

55

60

65

5 10 15 20 25 30 35 40 45 500 70656055

80

75

70

1.5m

3.15

m

30°

83.5°

30m

24m

72m

66m

60m

54m

48m

42m

36m 

4.4m

Working Radius (m)

15 t Hook

Height Above G

round(m)

Maximum Boom Angle

Minimum Boom Angle

Page 16: HYDRAULIC CRAWLER CRANE · SCX3500-3 SPECIFICATIONS Specifications Model CUMMINS QSL9 Type 4-cycle, water-cooled,Direct-injection,Turbo-charger Diesel engine Displacement 8.9 Liters

16

SpecificationsWorking Ranges

SPECIFICATIONSSCX3500-3

■Main Boom with Aux. Sheave (Rear end Radius: Short)

5

10

15

20

25

30

35

40

45

50

55

60

65

5 10 15 20 25 30 35 40 45 500 70656055

80

75

70

1.5m

3.15

m

30°

83.5°

24m

30m

72m

66m

60m

54m

48m

42m

36m 

6.0m

5.8m

5.6m

Working Radius (m)

180 t Hook 45 t Hook100 t Hook

Height Above G

round(m)

Maximum Boom Angle

Minimum Boom Angle

Page 17: HYDRAULIC CRAWLER CRANE · SCX3500-3 SPECIFICATIONS Specifications Model CUMMINS QSL9 Type 4-cycle, water-cooled,Direct-injection,Turbo-charger Diesel engine Displacement 8.9 Liters

17

SpecificationsWorking Ranges

SPECIFICATIONS SCX3500-3

■Crane Jib (Rear end Radius: Standard)

4.3m

4.8m

0 5 15 25 35 45 55 65 70605040302010

5101520253035404550556065707580

75

30°

40°

50°

125120

1.5m

3.15

m

100

115110

959085

60°

70°80°

105

83.5°

80 85 90

30°

42m

48m

54m

60m

66m

72m

10°

Working Radius (m)

45 t Hook15 t Hook

Height Above G

round

(m)

37m Crane Jib

31m Crane Jib

25m Crane Jib

19m Crane Jib

13m Crane Jib

37m Crane Jib

31m Crane Jib

25m Crane Jib

19m Crane Jib

13m Crane Jib

Maximum Boom Angle

Page 18: HYDRAULIC CRAWLER CRANE · SCX3500-3 SPECIFICATIONS Specifications Model CUMMINS QSL9 Type 4-cycle, water-cooled,Direct-injection,Turbo-charger Diesel engine Displacement 8.9 Liters

18

SpecificationsWorking Ranges

SPECIFICATIONSSCX3500-3

■Main Boom with Crane Jib (Rear end Radius: Standard)

0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75

10095908580757065605550

2015

25

3530

4540

510

1.5m

3.15

m

40°

50°

30°

83.5° 70° 60°

42m

48m

54m

60m

66m

72m

6.0m

5.8m

5.6m

30°10°

Working Radius (m)

Height Above G

round

(m)

45 t Hook100 t Hook

Crane Jib 13m to 31m

180 t Hook

Crane Jib 13m to 37m

Page 19: HYDRAULIC CRAWLER CRANE · SCX3500-3 SPECIFICATIONS Specifications Model CUMMINS QSL9 Type 4-cycle, water-cooled,Direct-injection,Turbo-charger Diesel engine Displacement 8.9 Liters

19

SpecificationsGross Rated Load Table

SPECIFICATIONS SCX3500-3

Gross Rated Load Table

■Main Boom (Rear end Radius: Standard)

Unit ton

Head18 24 30 36 42 48 54 60 66 72

m9.5- x -5 350.0 180.0t 6.5m x 56 283.6 180.0 180.0t 7.2m x 7.9m x 67 244.7 180.0 180.0 180.0t 170.0t 8.6m x 78 214.9 180.0 180.0 180.0 170.0 157.0t 9.3m x 9.9m x 89 181.5 180.0 180.0 180.0 170.0 157.0 131.0t 118.0t 10.6m x 11.3m x 910 154.8 180.0 180.0 180.0 170.0 157.0 131.0 118.0 104.0t 102.9t 1012 118.2 155.1 154.6 153.8 144.3 143.1 131.0 118.0 104.0 101.7 1214 93.2 130.6 129.2 128.4 121.1 119.9 112.8 106.2 104.0 98.5 1416 76.4 109.9 109.8 108.9 103.7 102.6 97.0 91.7 90.4 85.4 1618 17.7m x 92.5 92.4 91.9 90.3 89.2 84.6 80.2 79.0 74.8 1820 65.8t 79.4 79.3 78.7 78.3 77.6 74.6 70.9 69.7 66.1 20

22 9.85 0.26 2.56 4.66 3.76 0.86 5.86 1.96 0.96 2242 8.25 6.55 6.75 4.85 1.95 8.95 3.06 8.06 x m0.3242

7.46 62 t 54.1 53.5 53.1 52.3 51.7 50.9 50.1 47.6 2682 6.34 6.44 2.54 0.64 7.64 5.74 9.74 4.84 8203 8.83 8.93 5.04 3.14 9.14 7.24 2.34 x m2.8203

9.74 23 t 39.1 38.6 37.9 37.2 36.4 35.7 34.7 3243 1.13 1.23 8.23 6.33 3.43 1.53 x m4.3343

6.63 63 t 32.0 31.2 30.5 29.7 29.0 28.0 3683 2.52 3.62 9.62 8.72 5.82 3.92 8304 8.22 9.32 5.42 4.52 1.62 x m6.8304

6.82 24 t 24.0 23.2 22.3 21.7 20.6 4244 7.81 7.91 4.02 3.12 x m8.3444

46 22.2t 19.5 18.6 17.9 16.9 4648 17.9 17.0 16.3 15.3 4850 49.0m x 15.6 14.9 13.8 5052 17.2t 14.3 13.6 12.5 5254 13.0 12.3 11.3 5456 54.2m x 11.2 10.2 5658 12.9t 10.2 9.1 5860 59.4m x 8.2 6062 9.5t 7.3 6264 6.5 6466 64.6m x 6668 6.2t 68

Boom Length (m)

Boom Length (m) 18 24 30 36 42 48 54 60 66 72Equivalent Mass (ton) 0.2 0.3 0.5 0.7 0.8 0.9 1.2 1.4 1.6 1.7

10. 18m boom with Hammer Head Boom, 350t Hook, and 28 falls.

Hook HookCapacity 13falls 12falls 11falls 10falls 9falls 8falls 7falls 6falls 5falls 4falls 3falls 2falls 1fall

180t 3.34 180 170 157 144 131 118 104 90 76 61 - - -100t 3.11 - - - - - - 100 90 76 61 46 31 -45t 2.17 - - - - - - - - - - 45 31 -15t 0.62 - - - - - - - - - - - - 15

Maximum Rated Load (ton)

4. Working radius is the horizontal distance from the swing center to the center of gravity of a lifted load.

Hammer Boom Top

such as hook, from figures shown above.

7. Correlation between the number of reeved lines, maximum rated loads, hook mass are shown in the table below.

Mass (ton)

1. The rated loads are determined according to EN13000 rating on the condition that the machine is stationed on firm, level ground.2. To calculate the maximum load that can actually be lifted, deduct mass of all lifting accessories,

3. The figures surrounded by bold lines are based on factors other than those which would cause a tipping condition.

5. The 145 ton counter weight and 25 ton lower weight are required for all capacities on these charts.6. Figures described as OOm x OOt in the tables indicate "working radius" m x "rated load" ton.

9. The rated total load when the operation being performed with the rear post support pendant attached is the value remaining when the value in chart below is deducted from the rated total load chart.

Radius (m)Working

Radius (m)Working

8. The necessary mass to lower the hook refers "Lowerable Boom Hook Mass" on page 10.

Page 20: HYDRAULIC CRAWLER CRANE · SCX3500-3 SPECIFICATIONS Specifications Model CUMMINS QSL9 Type 4-cycle, water-cooled,Direct-injection,Turbo-charger Diesel engine Displacement 8.9 Liters

20

SpecificationsGross Rated Load Table

SPECIFICATIONSSCX3500-3

■Aux. Sheave (Rear end Radius: Standard)

Unit tonBoom Length (m)

24 30 36 42 48 54 60 66 72 7.5 15.0 8.2m x 8.9m x 7.5

8 15.0 15.0t 15.0t 9.5m x 89 15.0 15.0 15.0 15.0t 9x m6.11x m9.01x m2.0110 15.0 15.0 15.0 15.0 15.0t 15.0t 15.0t 12.3m x 12.9m x 1012 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0t 15.0t 1214 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 1416 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 1618 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 1820 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 2022 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 2224 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 2426 24.9m x 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 2628 15.0t 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 28

03 0.51 0.51 0.51 0.51 0.51 0.51 0.51 0.51 0323 0.51 0.51 0.51 0.51 0.51 0.51 0.51 x m1.0323

0.51 43 t 15.0 15.0 15.0 15.0 15.0 15.0 15.0 3463 0.51 0.51 0.51 0.51 0.51 0.51 x m3.5363

0.51 83 t 15.0 15.0 15.0 15.0 15.0 15.0 3804 0.51 0.51 0.51 0.51 0.51 0.51 0424 0.51 0.51 0.51 0.51 0.51 x m5.0424

0.51 44 t 15.0 15.0 15.0 15.0 15.0 4464 0.51 0.51 0.51 0.51 x m6.5464

0.51 84 t 15.0 15.0 15.0 15.0 4850 15.0 15.0 14.8 13.7 5052 50.8m x 14.1 13.4 12.4 5254 15.0t 12.8 12.1 11.1 5456 11.7 11.0 9.9 5658 9.9 8.9 5860 8.9 7.9 6062 61.2m x 7.0 6264 8.4t 6.2 6466 5.4 6668 66.4m x 6870 5.2t 70

1. The rated loads are determined according to EN13000 rating on the condition that the machine is stationed on firm, level ground.2. To calculate the maximum load that can actually such as boom hook and jib hook, from figures shown above.3. The figures surrounded by bold lines are based on factors other than those which would cause a tipping condition.

5. The 145 ton counter weight and 25 ton lower weight are required for all capacities on these charts.6. Fig

Hook

180t 3.34100t 3.1145t 2.1715t 0.62

Mass (ton)Hook

Capacity

4. Working radius is the horizontal distance from the swing center to the center of gravity of a lifted load.

be lifted, deduct mass of all lifting accessories,

7. Hook mass are shown in the table below.

8. The rated total load when the operation being performed with the rear post support pendant attached is the value remaining when the value in chart below is deducted from the rated total load chart.

Boom Length (m) 24 30 36 42 48 54 60 66 72Equivalent Mass (ton) 0.3 0.5 0.7 0.8 0.9 1.2 1.4 1.6 1.7

ures described as OOm x OOt in the tables indicate "working radius" m x "rated load" ton.

Radius (m)Working

Radius (m)Working

Page 21: HYDRAULIC CRAWLER CRANE · SCX3500-3 SPECIFICATIONS Specifications Model CUMMINS QSL9 Type 4-cycle, water-cooled,Direct-injection,Turbo-charger Diesel engine Displacement 8.9 Liters

21

SpecificationsGross Rated Load Table

SPECIFICATIONS SCX3500-3

■Main Boom with Aux. Sheave (Rear end Radius: Standard)

Unit tonBoom Length (m)

24 30 36 42 48 54 60 66 72 5.9 180.0 6.5m x 5.9

6 180.0 180.0t 7.2m x 7.9m x 67 180.0 180.0 180.0t 170.0t 8.6m x 78 180.0 180.0 180.0 170.0 157.0t 9.3m x 9.9m x 89 180.0 180.0 180.0 170.0 157.0 131.0t 118.0t 10.6m x 11.3m x 910 180.0 180.0 180.0 170.0 157.0 131.0 118.0 104.0t 101.9t 1012 154.6 154.1 153.2 143.2 141.8 131.0 118.0 104.0 100.7 1214 129.4 128.2 127.3 120.0 118.6 111.6 105.0 103.6 97.5 1416 109.2 108.8 107.7 102.6 101.4 95.8 90.5 89.2 84.2 1618 91.8 91.7 91.1 89.2 88.0 83.4 79.1 77.8 73.6 1820 78.7 78.6 78.0 77.5 76.8 73.5 69.8 68.5 64.9 2022 68.4 68.4 67.8 67.3 66.6 65.3 64.0 60.9 57.7 2224 23.0m x 60.2 59.6 59.1 58.3 57.7 56.9 54.5 51.6 2426 64.1t 53.5 52.9 52.4 51.6 50.9 50.1 49.0 46.4 26

82 7.24 8.34 5.44 3.54 0.64 8.64 3.74 8.74 8203 0.83 0.93 7.93 6.04 3.14 1.24 6.24 x m2.8203

3.74 23 t 38.5 38.0 37.2 36.5 35.6 34.9 33.9 3243 3.03 4.13 1.23 0.33 7.33 5.43 x m4.3343

0.63 63 t 31.5 30.6 29.9 29.0 28.3 27.2 3683 5.42 6.52 3.62 1.72 9.72 8.82 8304 1.22 1.32 8.32 7.42 5.52 x m6.8304

0.82 24 t 23.4 22.6 21.7 21.0 19.9 4244 0.81 0.91 7.91 7.02 x m8.3444

7.12 64 t 18.9 18.0 17.3 16.2 4648 17.4 16.4 15.7 14.6 4850 49.0m x 15.0 14.2 13.2 5052 16.6t 13.7 12.9 11.8 5254 12.5 11.7 10.6 5456 54.2m x 10.6 9.5 5658 12.4t 9.6 8.5 5860 59.4m x 7.5 6062 8.9t 6.7 6264 5.9 6466 64.6m x 6668 5.6t 68

1. The rated loads are determined according to EN13000 rating on the condition that the machine is stationed on firm, level ground.2. To calculate the maximum load that can actually

3. The figures surrounded by bold lines are based on factors other than those which would cause a tipping condition.

5. The 145 ton counter weight and 25 ton lower weight are required for all capacities on these charts.6. Fig

9. The rated total load when the operation being performed with the rear post support pendant attached is the value remaining when the value in chart below is deducted from the rated total load chart.

Hook Hook13falls 12falls 11falls 10falls 9falls 8falls 7falls 6falls 5falls 4falls 3falls 2falls 1fall

180t 3.34 180 170 157 144 131 118 104 90 76 61-136416670900111.3t001

45t 2.17 - - - - 45 31 -15t 0.62 - - - - - - 15

Maximum Rated Load (ton)

Boom Length (m) 24 30 36 42 48 54 60 66 72Equivalent Mass (ton) 0.3 0.5 0.7 0.8 0.9 1.2 1.4 1.6 1.7

4. Working radius is the horizontal distance from the swing center to the center of gravity of a lifted load.

Capacity Mass (ton)

be lifted, deduct mass of all lifting accessories, such as hook, from figures shown above.

7. Correlation between the number of reeved lines, maximum rated loads, hook mass are shown in the table below.ures described as OOm x OOt in the tables indicate "working radius" m x "rated load" ton.

8. The necessary mass to lower the hook refers "Lowerable Boom Hook Mass" on page 10.

---

------

---

---

---

---

Radius (m)Working

Radius (m)Working

Page 22: HYDRAULIC CRAWLER CRANE · SCX3500-3 SPECIFICATIONS Specifications Model CUMMINS QSL9 Type 4-cycle, water-cooled,Direct-injection,Turbo-charger Diesel engine Displacement 8.9 Liters

22

SpecificationsGross Rated Load Table

SPECIFICATIONSSCX3500-3

■Main Boom (Rear end Radius: Short)

Unit tonBoom Length (m)

24 30 36 42 48 54 60 66 72 5.9 180.0 6.5m x 5.9

6 180.0 180.0t 7.2m x 7.9m x 67 180.0 180.0 180.0t 170.0t 8.6m x 78 180.0 180.0 180.0 170.0 157.0t 9.3m x 9.9m x 89 180.0 180.0 180.0 170.0 157.0 131.0t 118.0t 10.6m x 11.3m x 910 180.0 180.0 176.9 170.0 157.0 131.0 118.0 104.0t 100.0t 1012 146.3 143.0 140.4 138.4 136.5 131.0 118.0 104.0 100.0 1214 120.3 117.7 115.5 113.8 112.1 110.5 105.5 104.0 97.6 1416 101.3 99.3 97.4 95.9 94.4 92.9 91.0 89.8 84.8 1618 86.7 85.3 83.7 82.4 80.9 79.5 78.2 77.1 74.2 1820 75.1 74.2 72.9 71.7 70.4 69.0 67.7 66.7 65.5 2022 65.4 65.2 64.1 63.1 61.8 60.6 59.3 58.3 57.1 2224 23.0m x 57.7 56.9 56.0 54.8 53.6 52.4 51.4 50.2 2426 60.2t 51.2 50.7 50.0 48.9 47.8 46.6 45.6 44.5 26

82 6.93 7.04 6.14 8.24 9.34 9.44 5.54 5.54 8203 4.53 5.63 4.73 5.83 5.93 5.04 8.04 x m2.8203

0.54 23 t 36.7 36.6 35.7 34.7 33.7 32.8 31.7 3243 5.82 6.92 4.03 4.13 4.23 1.33 x m4.3343

1.43 63 t 30.0 29.4 28.5 27.5 26.7 25.6 3683 1.32 1.42 9.42 9.52 7.62 1.72 8304 8.02 8.12 6.22 5.32 2.42 x m6.8304

3.62 24 t 22.0 21.3 20.5 19.7 18.7 4244 8.61 8.71 5.81 3.91 x m8.3444

1.02 64 t 17.5 16.7 16.1 15.1 4648 15.8 15.1 14.5 13.5 4850 49.0m x 13.6 13.0 12.1 5052 14.9t 12.1 11.6 10.7 5254 10.8 10.3 9.4 5456 54.2m x 9.1 8.3 5658 10.6t 7.9 7.2 5860 59.4m x 6.1 6062 7.2t 5.1 6264 62.2m x 6466 5.0t 66

1. The rated loads are determined according to EN13000 rating on the condition that the machine is stationed on firm, level ground.2. To calculate the maximum load that can actually

3. The figures surrounded by bold lines are based on factors other than those which would cause a tipping condition.

5. The 145 ton counter weight and 25 ton lower weight are required for all capacities on these charts.6. Fig

9. The rated total load when the operation being performed with the rear post support pendant attached is the value remaining when the value in chart below is deducted from the rated total load chart.

HookCapacity

Hook13falls 12falls 11falls 10falls 9falls 8falls 7falls 6falls 5falls 4falls 3falls 2falls 1fall

3.34 180 170 157 144 131 118 104 90 76 61 - - -3.11 - - - - - - 100 90 76 61 46 31 -2.17 - - - - - - - - - - 45 31 -0.62 - - - - - - - - - - - - 15

Maximum Rated Load (ton)

Boom Length (m) 24 30 36 42 48 54 60 66 72Equivalent Mass (ton) 0.3 0.5 0.7 0.8 0.9 1.2 1.4 1.6 1.7

180t100t45t15t

Mass (ton)

4. Working radius is the horizontal distance from the swing center to the center of gravity of a lifted load.

be lifted, deduct mass of all lifting accessories, such as hook, from figures shown above.

7. Correlation between the number of reeved lines, maximum rated loads, hook mass are shown in the table below.ures described as OOm x OOt in the tables indicate "working radius" m x "rated load" ton.

8. The necessary mass to lower the hook refers "Lowerable Boom Hook Mass" on page 10.

Radius (m)Working

Radius (m)Working

Page 23: HYDRAULIC CRAWLER CRANE · SCX3500-3 SPECIFICATIONS Specifications Model CUMMINS QSL9 Type 4-cycle, water-cooled,Direct-injection,Turbo-charger Diesel engine Displacement 8.9 Liters

23

SpecificationsGross Rated Load Table

SPECIFICATIONS SCX3500-3

■Aux. Sheave (Rear end Radius: Short)

Unit tonBoom Length (m)

24 30 36 42 48 54 60 66 72 7.5 15.0 8.2m x 8.9m x 7.5

8 15.0 15.0t 15.0t 9.5m x 89 15.0 15.0 15.0 15.0t 9x m6.11x m9.01x m2.0110 15.0 15.0 15.0 15.0 15.0t 15.0t 15.0t 12.3m x 12.9m x 1012 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0t 15.0t 1214 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 1416 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 1618 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 1820 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 2022 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 2224 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 2426 24.9m x 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 2628 15.0t 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 28

03 0.51 0.51 0.51 0.51 0.51 0.51 0.51 0.51 0323 0.51 0.51 0.51 0.51 0.51 0.51 0.51 x m1.0323

0.51 43 t 15.0 15.0 15.0 15.0 15.0 15.0 15.0 3463 0.51 0.51 0.51 0.51 0.51 0.51 x m3.5363

0.51 83 t 15.0 15.0 15.0 15.0 15.0 15.0 3804 0.51 0.51 0.51 0.51 0.51 0.51 0424 0.51 0.51 0.51 0.51 0.51 x m5.0424

0.51 44 t 15.0 15.0 15.0 15.0 15.0 4464 0.51 0.51 0.51 0.51 x m6.5464

0.51 84 t 15.0 15.0 14.5 13.6 4850 14.2 13.6 13.0 12.1 5052 50.8m x 12.1 11.6 10.7 5254 13.6t 10.8 10.3 9.4 5456 9.5 9.1 8.2 5658 7.9 7.1 5860 6.8 6.0 6062 61.2m x 5.0 6264 6.1t 64

1. The rated loads are determined according to EN13000 rating on the condition that the machine is stationed on firm, level ground.2. To calculate the maximum load that can actually such as boom hook and jib hook, from figures shown above. j3. The figures surrounded by bold lines are based on factors other than those which would cause a tipping condition.

5. The 145 ton counter weight and 25 ton lower weight are required for all capacities on these charts.6. Fig

4. Working radius is the horizontal distance from the swing center to the center of gravity of a lifted load.

be lifted, deduct mass of all lifting accessories,

7. Hook mass are shown in the table below.

8. The rated total load when the operation being performed with the rear post support pendant attached is the value remaining when the value in chart below is deducted from the rated total load chart.

Boom Length (m) 24 30 36 42 48 54 60 66 72Equivalent Mass (ton) 0.3 0.5 0.7 0.8 0.9 1.2 1.4 1.6 1.7

ures described as OOm x OOt in the tables indicate "working radius" m x "rated load" ton.

HookCapacity

Hook

3.343.112.170.62

180t100t45t15t

Mass (ton)

Radius (m)Working

Radius (m)Working

Page 24: HYDRAULIC CRAWLER CRANE · SCX3500-3 SPECIFICATIONS Specifications Model CUMMINS QSL9 Type 4-cycle, water-cooled,Direct-injection,Turbo-charger Diesel engine Displacement 8.9 Liters

24

SpecificationsGross Rated Load Table

SPECIFICATIONSSCX3500-3

■Main Boom with Aux. Sheave (Rear end Radius: Short)

Unit tonBoom Length (m)

24 30 36 42 48 54 60 66 72 5.9 180.0 6.5m x 5.9

6 180.0 180.0t 7.2m x 7.9m x 67 180.0 180.0 180.0t 170.0t 8.6m x 78 180.0 180.0 180.0 170.0 157.0t 9.3m x 9.9m x 89 180.0 180.0 180.0 170.0 157.0 131.0t 118.0t 10.6m x 11.3m x 910 180.0 178.8 175.5 170.0 157.0 131.0 118.0 104.0t 100.0t 1012 145.1 141.8 139.1 137.1 135.1 131.0 118.0 104.0 100.0 1214 119.1 116.6 114.3 112.6 110.8 109.2 104.3 102.9 96.1 1416 100.2 98.2 96.3 94.8 93.1 91.6 89.9 88.5 83.6 1618 85.7 84.2 82.6 81.2 79.7 78.3 76.9 75.8 73.0 1820 74.0 73.2 71.8 70.6 69.2 67.8 66.5 65.4 64.2 2022 64.4 64.2 63.0 62.0 60.7 59.4 58.1 57.1 55.8 2224 23.0m x 56.7 55.8 54.9 53.7 52.5 51.2 50.2 49.0 2426 59.3t 50.2 49.7 49.0 47.8 46.6 45.4 44.4 43.3 26

82 4.83 5.93 5.04 7.14 8.24 9.34 5.44 6.44 8203 2.43 3.53 3.63 4.73 5.83 5.93 9.93 x m2.8203

0.44 23 t 35.8 35.6 34.7 33.7 32.6 31.7 30.5 3243 3.72 4.82 3.92 4.03 4.13 1.23 x m4.3343

1.33 63 t 29.1 28.4 27.5 26.4 25.6 24.5 3683 9.12 0.32 8.32 8.42 7.52 2.62 8304 6.91 7.02 5.12 5.22 3.32 x m6.8304

4.52 24 t 21.0 20.3 19.4 18.6 17.6 4244 7.51 7.61 5.71 4.81 x m8.3444

1.91 64 t 16.5 15.7 15.0 14.0 4648 14.8 14.1 13.4 12.4 4850 49.0m x 12.6 11.9 11.0 5052 14.0t 11.2 10.6 9.6 5254 9.8 9.3 8.4 5456 54.2m x 8.1 7.2 5658 9.7t 7.0 6.1 5860 59.4m x 5.1 6062 6.2t 60.2m x 6264 5.0t 64

1. The rated loads are determined according to EN13000 rating on the condition that the machine is stationed on firm, level ground.2. To calculate the maximum load that can actually

3. The figures surrounded by bold lines are based on factors other than those which would cause a tipping condition.

5. The 145 ton counter weight and 25 ton lower weight are required for all capacities on these charts.6. Fig

9. The rated total load when the operation being performed with the rear post support pendant attached is the value remaining when the value in chart below is deducted from the rated total load chart.

HookCapacity

HookMass (ton) 13falls 12falls 11falls 10falls 9falls 8falls 7falls 6falls 5falls 4falls 3falls 2falls 1fall

180t 3.34 180 170 157 144 131 118 104 90 76 61-136416670900111.3t001

45t 2.17 - - - - 45 31 -15t 0.62 - - - - - - 15

Maximum Rated Load (ton)

Boom Length (m) 24 30 36 42 48 54 60 66 72Equivalent Mass (ton) 0.3 0.5 0.7 0.8 0.9 1.2 1.4 1.6 1.7

4. Working radius is the horizontal distance from the swing center to the center of gravity of a lifted load.

be lifted, deduct mass of all lifting accessories, such as hook, from figures shown above.

7. Correlation between the number of reeved lines, maximum rated loads, hook mass are shown in the table below.ures described as OOm x OOt in the tables indicate "working radius" m x "rated load" ton.

8. The necessary mass to lower the hook refers "Lowerable Boom Hook Mass" on page 10.

- --

---

--

---

---

---

---

-

Radius (m)Working

Radius (m)Working

Page 25: HYDRAULIC CRAWLER CRANE · SCX3500-3 SPECIFICATIONS Specifications Model CUMMINS QSL9 Type 4-cycle, water-cooled,Direct-injection,Turbo-charger Diesel engine Displacement 8.9 Liters

25

SpecificationsGross Rated Load Table

SPECIFICATIONS SCX3500-3

■Crane Jib (Rear end Radius: Standard)

1. The rated loads are determined according to EN13000 rating on the condition that the machine is stationed on firm, level ground.2. To calculate the maximum load that can actually be lifted, deduct mass of all lifting accessories, such as boom hook and jib hook, from figures shown above.3. The figures surrounded by bold lines are based on factors other than those which would cause a tipping condition.4. Working radius is the horizontal distance from the swing center to the center of gravity of a lifted load.5. The 145 ton counter weight and 25 ton lower weight are required for all capacities on these charts.6. Figures described as OOm x OOt in the tables indicate "working radius" m x "rated load" ton.7. Correlation between the number of reeved lines, maximum rated loads, hook mass are shown in the table below.

10. The rated total load when the operation being performed with the rear post support pendant attached is the value remaining when the value in chart below is deducted from the rated total load chart.

8. The necessary mass to lower the boom hook refers "Lowerable Boom Hook Mass" on page 10.9. The necessary mass to lower the crane jib hook refers "Lowerable Crane Jib Hook Mass" on page 10.

Boom Length (m)Equivalent Mass (ton)

42 48 54 60 66 720.8 0.9 1.2 1.4 1.6 1.7

Hook HookCapacity

180t 3.34100t 3.1145t 2.1715t 0.62

Maximum Rated Load (ton)

-

1 fall---

15

2 falls-

3030

Mass (ton)

Unit tonBoom Length (m) neL mooB24 gth (m)

Jib Length (m) neL biJ9131 gth (m)Offset Angle (deg.) Offset Angle (deg.)

Working Radius (m) Working Radius (m) m4.21- x 13.8m x -

m1.41t0.52 t0.51 0.03 1.21 x 12.114 30.0 15.0 16.4m x 41t0.51 9.42

61 0.51 2.42 t9.31 0.51 0.03 6181 0.51 5.32 4.31 0.51 0.03 81

20 30.0 15.0 12.8 22.8 15.0 10.4 2022 29.0 15.0 12.3 22.2 15.0 9.9 2224 27.1 15.0 11.8 21.6 15.0 9.5 2426 25.5 15.0 11.4 21.0 15.0 9.2 2628 24.0 15.0 11.0 20.4 15.0 8.8 2830 22.7 15.0 10.7 19.9 15.0 8.5 3032 21.6 15.0 10.4 18.8 15.0 8.2 3234 20.5 15.0 10.1 17.9 15.0 7.9 3436 19.6 15.0 9.8 17.0 15.0 7.7 3638 18.7 15.0 9.6 16.2 15.0 7.5 3840 17.9 15.0 9.4 15.5 15.0 7.3 4042 17.2 15.0 9.2 14.9 14.9 7.1 4244 16.6 15.0 9.0 14.3 14.3 6.9 4446 16.0 15.0 8.9 13.8 13.8 6.8 4648 15.5 15.0 8.8 13.3 13.3 6.6 4850 15.0 15.0 8.7 12.8 12.8 6.5 5052 51.8m x 14.5 8.7 12.4 12.4 6.4 5254 14.6t 52.6m x 53.3m x 12.0 12.0 6.3 54

65 3.6 6.11 6.11 t6.8 t4.41 6558 57.5m x 11.2 6.3 5860 11.4t 58.2m x 59.3m x 6062 11.2t 6.2t 62

No. of part line 2 1 1 2 1 1 No. of part line

03010301

Page 26: HYDRAULIC CRAWLER CRANE · SCX3500-3 SPECIFICATIONS Specifications Model CUMMINS QSL9 Type 4-cycle, water-cooled,Direct-injection,Turbo-charger Diesel engine Displacement 8.9 Liters

26

SpecificationsGross Rated Load Table

SPECIFICATIONSSCX3500-3

■Crane Jib (Rear end Radius: Standard)

Unit tonBoom Length (m) neL mooB24 gth (m)

Jib Length (m) neL biJ731352 gth (m)Offset Angle (deg.) Offset Angle (deg.)

Working Radius (m) Working Radius (m)12 15.5m x 15.8m x 12

m5.71t0.51 t0.91 41 x 14 m2.91t1.41 0.51 9.81 61 x 16

81t9.8 0.41 0.51 3.81 8120 17.7 15.0 23.6m x 02 8.8 5.31

22 6.8 0.31 t1.8 0.51 2.71 2224 16.6 15.0 8.0 12.5 27.1m x 8.3 2426 16.0 15.0 7.7 12.1 7.5t 8.0 2628 15.5 15.0 7.3 11.6 7.3 7.6 2830 15.0 15.0 7.1 11.2 7.0 7.3 3032 14.5 14.5 6.8 10.8 6.8 7.0 3234 14.0 14.0 6.5 10.5 6.5 6.8 3436 13.5 13.5 6.3 10.1 6.3 6.5 3638 13.1 13.1 6.1 9.8 6.1 6.3 3840 12.7 12.7 5.9 9.5 5.9 6.0 4042 12.4 12.4 5.7 9.3 5.7 5.8 4244 12.0 12.0 5.6 9.0 5.5 5.6 4446 11.7 11.7 5.4 8.8 5.4 5.5 4648 11.4 11.4 5.3 8.5 5.2 5.3 4850 11.1 11.1 5.2 8.3 5.1 5.1 5052 10.7 10.7 5.1 8.1 51.0m x 5.0 52

45t0.5 9.7 0.5 5.01 5.01 4565 7.7 2.01 2.01 6585 6.7 9.9 9.9 8506 4.7 6.9 6.9 0626 2.7 3.9 3.9 26

64 63.1m x 63.9m x 46 1.7 66 9.6 t0.9 t2.9 66

68 86 7.6 70 69.5m x 7072 27t6.6

No. of part line 2 1 1 1 1 1 No. of part line

30 10010301

Unit tonBoom Length (m) neL mooB84 gth (m)

Jib Length (m) neL biJ9131 gth (m)Offset Angle (deg.) Offset Angle (deg.)

Working Radius (m) Working Radius (m)- 12.8m x 13.1m x -

m5.41t0.51 t0.03 21 x 14.8m x 1214 30.0 15.0 17.1m x 41t0.51 t8.42

61 0.51 3.42 t8.31 0.51 0.03 6118 30.0 15.0 13.6 23.7 15.0 20.7m x 1820 30.0 15.0 13.0 23.1 15.0 10.3t 2022 30.0 15.0 12.5 22.5 15.0 10.1 2224 28.7 15.0 12.1 21.9 15.0 9.7 2426 27.0 15.0 11.7 21.4 15.0 9.3 2628 25.5 15.0 11.3 21.0 15.0 9.0 2830 24.2 15.0 11.0 20.5 15.0 8.7 3032 23.0 15.0 10.7 19.9 15.0 8.4 3234 21.9 15.0 10.4 19.0 15.0 8.2 3436 21.0 15.0 10.1 18.1 15.0 7.9 3638 20.1 15.0 9.9 17.3 15.0 7.7 3840 19.2 15.0 9.7 16.6 15.0 7.5 4042 18.5 15.0 9.4 15.9 15.0 7.3 4244 17.8 15.0 9.3 15.3 15.0 7.1 4446 17.2 15.0 9.1 14.7 14.7 7.0 4648 16.6 15.0 9.0 14.2 14.2 6.8 4850 16.1 15.0 8.8 13.7 13.7 6.7 5052 15.6 15.0 8.7 13.2 13.2 6.6 5254 15.1 15.0 8.7 12.8 12.8 6.5 5456 14.7 14.7 8.6 12.4 12.4 6.4 5658 57.0m x 57.8m x 8.6 12.1 12.1 6.3 5860 14.3t 14.0t 58.5m x 11.8 11.8 6.3 60

26 2.6 5.11 5.11 t6.8 2664 62.7m x 63.4m x 6.2 6466 11.4t 11.3t 64.5m x 6668 6.1t 68

No. of part line 2 1 1 2 1 1 No. of part line

03010301

* For notes about the table above, refer to page 25.

Page 27: HYDRAULIC CRAWLER CRANE · SCX3500-3 SPECIFICATIONS Specifications Model CUMMINS QSL9 Type 4-cycle, water-cooled,Direct-injection,Turbo-charger Diesel engine Displacement 8.9 Liters

27

SpecificationsGross Rated Load Table

SPECIFICATIONS SCX3500-3

■Crane Jib (Rear end Radius: Standard)

Unit tonBoom Length (m) neL mooB84 gth (m)

Jib Length (m) neL biJ731352 gth (m)Offset Angle (deg.) Offset Angle (deg.)

Working Radius (m) Working Radius (m)14 16.2m x 16.5m x 14

m2.81t0.51 t9.81 61 x 19.9m x 1681t9.8 t9.31 0.51 5.81 8102 9.8 6.31 0.51 9.71 02

22 17.4 15.0 24.2m x 22 7.8 2.31 24 16.9 15.0 8.0t 12.8 27.8m x 8.5 2426 16.4 15.0 7.8 12.3 7.4t 8.2 2628 15.9 15.0 7.5 11.9 7.4 7.8 2830 15.4 15.0 7.2 11.5 7.1 7.5 3032 14.9 14.9 6.9 11.1 6.9 7.2 3234 14.5 14.5 6.7 10.8 6.6 7.0 3436 14.1 14.1 6.5 10.4 6.4 6.7 3638 13.6 13.6 6.3 10.1 6.2 6.5 3840 13.2 13.2 6.1 9.9 6.0 6.3 4042 12.9 12.9 5.9 9.6 5.8 6.0 4244 12.5 12.5 5.7 9.3 5.7 5.9 4446 12.2 12.2 5.6 9.1 5.5 5.7 4648 11.9 11.9 5.5 8.9 5.4 5.5 4850 11.5 11.5 5.3 8.6 5.2 5.3 5052 11.2 11.2 5.2 8.4 5.1 5.2 5254 11.0 11.0 5.1 8.2 5.0 5.0 54

65 1.8 0.5 8.01 8.01 6585 9.7 5.01 5.01 8506 7.7 2.01 2.01 0626 6.7 9.9 9.9 2646 4.7 6.9 6.9 4666 2.7 4.9 4.9 6686 0.7 2.9 2.9 86

70 68.3m x 69.1m x 07 9.6 27 8.6 t0.9 t1.9 27

74 47 7.6 76 74.7m x 7678 87t6.6

No. of part line 2 1 1 1 1 1 No. of part line

1003010301

Unit tonBoom Length (m) neL mooB45 gth (m)

Jib Length (m) neL biJ9131 gth (m)Offset Angle (deg.) Offset Angle (deg.)

Working Radius (m) Working Radius (m)- 13.4m x 13.8m x -

m1.51t0.51 t0.03 21 x 15.5m x 1214 30.0 15.0 17.8m x 41t0.51 t0.52

61 0.51 7.42 t7.31 0.51 0.03 6118 30.0 15.0 13.7 24.1 15.0 21.4m x 1820 30.0 15.0 13.2 23.5 15.0 10.3t 2022 30.0 15.0 12.7 23.0 15.0 10.2 2224 30.0 15.0 12.3 22.4 15.0 9.8 2426 28.4 15.0 11.9 21.9 15.0 9.5 2628 26.9 15.0 11.6 21.4 15.0 9.1 2830 25.5 15.0 11.3 21.0 15.0 8.9 3032 24.3 15.0 10.9 20.5 15.0 8.6 3234 23.2 15.0 10.7 20.0 15.0 8.3 3436 22.2 15.0 10.4 19.1 15.0 8.1 3638 21.3 15.0 10.1 18.3 15.0 7.9 3840 20.5 15.0 9.9 17.5 15.0 7.7 4042 19.7 15.0 9.7 16.8 15.0 7.5 4244 19.0 15.0 9.5 16.2 15.0 7.3 4446 18.3 15.0 9.3 15.6 15.0 7.2 4648 17.7 15.0 9.2 15.0 15.0 7.0 4850 17.1 15.0 9.0 14.5 14.5 6.9 5052 16.4 15.0 8.9 14.1 14.1 6.7 5254 15.1 15.0 8.8 13.6 13.6 6.6 5456 14.0 14.0 8.7 13.2 13.2 6.5 5658 12.9 12.9 8.6 12.8 12.8 6.4 5860 11.9 11.9 8.6 12.5 12.5 6.4 6062 11.0 11.0 8.6 11.9 11.9 6.3 6264 62.2m x 63.0m x 63.7m x 11.0 11.0 6.2 6466 10.9t 10.5t 8.6t 10.2 10.2 6.2 6668 67.9m x 9.4 6.2 6870 9.5t 68.6m x 69.7m x 7072 9.2t 6.2t 72

No. of part line 2 1 1 2 1 1 No. of part line

03010301

* For notes about the table above, refer to page 25.

Page 28: HYDRAULIC CRAWLER CRANE · SCX3500-3 SPECIFICATIONS Specifications Model CUMMINS QSL9 Type 4-cycle, water-cooled,Direct-injection,Turbo-charger Diesel engine Displacement 8.9 Liters

28

SpecificationsGross Rated Load Table

SPECIFICATIONSSCX3500-3

■Crane Jib (Rear end Radius: Standard)

Unit tonBoom Length (m) neL mooB45 gth (m)

Jib Length (m) neL biJ731352 gth (m)Offset Angle (deg.) Offset Angle (deg.)

Working Radius (m) Working Radius (m)14 16.8m x 17.2m x 14

m9.81t0.51 t1.91 61 x 16 m6.02t9.31 0.51 8.81 81 x 18

02t9.8 7.31 0.51 3.81 0222 17.7 15.0 24.9m x 22 7.8 3.31

42 6.8 0.31 t0.8 0.51 3.71 4226 16.7 15.0 7.8 12.6 28.5m x 8.3 2628 16.2 15.0 7.5 12.2 7.4t 8.0 2830 15.8 15.0 7.3 11.8 7.2 7.7 3032 15.3 15.0 7.0 11.4 6.9 7.4 3234 14.9 14.9 6.8 11.1 6.7 7.1 3436 14.4 14.4 6.6 10.7 6.5 6.9 3638 14.1 14.1 6.4 10.4 6.3 6.7 3840 13.7 13.7 6.2 10.1 6.1 6.5 4042 13.3 13.3 6.0 9.9 6.0 6.2 4244 13.0 13.0 5.9 9.6 5.8 6.1 4446 12.6 12.6 5.7 9.4 5.6 5.9 4648 12.3 12.3 5.6 9.2 5.5 5.7 4850 12.0 12.0 5.5 8.9 5.4 5.5 5052 11.8 11.8 5.3 8.7 5.2 5.4 5254 11.5 11.5 5.2 8.5 5.1 5.2 5456 11.2 11.2 5.1 8.4 5.0 5.1 56

85 0.5 2.8 0.5 9.01 9.01 8506 0.8 7.01 7.01 0626 9.7 5.01 5.01 2646 7.7 2.01 2.01 4666 6.7 9.9 9.9 6686 4.7 7.9 7.9 8607 2.7 5.9 5.9 0727 1.7 8.8 8.8 27

74 73.5m x 47 0.7 1.8 76 8.3t 74.3m x 67 8.6

87 7.6 t0.8 8780 79.9m x 8082 28t7.6

No. of part line 2 1 1 1 1 1 No. of part line

30 10 30 1010

Unit tonBoom Length (m) neL mooB06 gth (m)

Jib Length (m) neL biJ9131 gth (m)Offset Angle (deg.) Offset Angle (deg.)

Working Radius (m) Working Radius (m)12 14.1m x 14.5m x 15.8m x 12

m2.61t9.42 t0.51 t0.03 41 x 1416 30.0 15.0 18.5m x 61t0.51 8.42

81 0.51 3.42 t7.31 0.51 0.03 8102 0.51 7.32 3.31 0.51 0.03 02

22 30.0 15.0 12.9 23.1 15.0 10.2 2224 30.0 15.0 12.5 22.6 15.0 9.9 2426 29.6 15.0 12.1 22.1 15.0 9.6 2628 28.1 15.0 11.8 21.7 15.0 9.3 2830 26.8 15.0 11.5 21.2 15.0 9.0 3032 25.6 15.0 11.2 20.8 15.0 8.7 3234 24.4 15.0 10.9 20.4 15.0 8.5 3436 23.4 15.0 10.6 20.0 15.0 8.3 3638 22.5 15.0 10.4 19.2 15.0 8.0 3840 21.6 15.0 10.2 18.4 15.0 7.9 4042 20.8 15.0 10.0 17.7 15.0 7.7 4244 20.1 15.0 9.8 17.0 15.0 7.5 4446 19.4 15.0 9.6 16.4 15.0 7.3 4648 18.3 15.0 9.4 15.9 15.0 7.2 4850 16.8 15.0 9.3 15.3 15.0 7.0 5052 15.5 15.0 9.1 14.9 14.9 6.9 5254 14.2 14.2 9.0 14.4 14.4 6.8 5456 13.0 13.0 8.9 14.0 14.0 6.7 5658 12.0 12.0 8.8 12.9 12.9 6.6 5860 11.0 11.0 8.7 11.9 11.9 6.5 6062 10.0 10.0 8.6 11.0 11.0 6.4 6264 9.2 9.2 8.6 10.1 10.1 6.3 6466 8.4 8.4 8.6 9.3 9.3 6.3 6668 67.4m x 7.6 7.8 8.5 8.5 6.2 6870 7.9t 68.2m x 68.9m x 7.8 7.8 6.2 70

27 2.6 1.7 1.7 t4.7 t6.7 2774 73.1m x 73.8m x 6.2 7476 6.8t 6.5t 74.9m x 7678 6.2t 78

No. of part line 2 1 1 2 1 1 No. of part line

03010301

* For notes about the table above, refer to page 25.

Page 29: HYDRAULIC CRAWLER CRANE · SCX3500-3 SPECIFICATIONS Specifications Model CUMMINS QSL9 Type 4-cycle, water-cooled,Direct-injection,Turbo-charger Diesel engine Displacement 8.9 Liters

29

SpecificationsGross Rated Load Table

SPECIFICATIONS SCX3500-3

■Crane Jib (Rear end Radius: Standard)

Unit tonBoom Length (m) neL mooB06 gth (m)

Jib Length (m) neL biJ731352 gth (m)Offset Angle (deg.) Offset Angle (deg.)

Working Radius (m) Working Radius (m)14 17.5m x 17.9m x 14

m6.91t0.51 t9.81 61 x 16 m3.12t9.31 0.51 9.81 81 x 18

02t8.8 8.31 0.51 4.81 0222 17.9 15.0 25.6m x 22 8.8 5.31

42 6.8 2.31 t9.7 0.51 4.71 4226 17.0 15.0 7.9 12.8 29.2m x 8.5 2628 16.5 15.0 7.6 12.4 7.3t 8.1 2830 16.0 15.0 7.4 12.0 7.2 7.9 3032 15.6 15.0 7.1 11.7 7.0 7.6 3234 15.2 15.0 6.9 11.3 6.8 7.3 3436 14.8 14.8 6.7 11.0 6.6 7.1 3638 14.4 14.4 6.5 10.7 6.4 6.8 3840 14.1 14.1 6.3 10.4 6.2 6.6 4042 13.7 13.7 6.2 10.1 6.1 6.4 4244 13.4 13.4 6.0 9.9 5.9 6.2 4446 13.1 13.1 5.9 9.7 5.8 6.1 4648 12.7 12.7 5.7 9.4 5.6 5.9 4850 12.4 12.4 5.6 9.2 5.5 5.7 5052 12.2 12.2 5.5 9.0 5.4 5.6 5254 11.9 11.9 5.3 8.8 5.2 5.4 5456 11.6 11.6 5.2 8.6 5.1 5.3 5658 11.3 11.3 5.1 8.5 5.0 5.1 58

06 0.5 3.8 1.5 1.11 1.11 0626 1.8 0.5 9.01 9.01 2646 0.8 7.01 7.01 4666 8.7 0.01 0.01 6686 7.7 3.9 3.9 8607 5.7 5.8 5.8 0727 4.7 9.7 9.7 2747 3.7 2.7 2.7 4767 1.7 6.6 6.6 6787 0.7 1.6 1.6 87

80 78.7m x 79.5m x 08 4.6 28 9.5 t6.5 t9.5 28

84 48 4.5 86 85.1m x 8688 88t1.5

No. of part line 2 1 1 1 1 1 No. of part line

30 10 30 1010

* For notes about the table above, refer to page 25.

Page 30: HYDRAULIC CRAWLER CRANE · SCX3500-3 SPECIFICATIONS Specifications Model CUMMINS QSL9 Type 4-cycle, water-cooled,Direct-injection,Turbo-charger Diesel engine Displacement 8.9 Liters

30

SpecificationsGross Rated Load Table

SPECIFICATIONSSCX3500-3

■Crane Jib (Rear end Radius: Standard)

Unit tonBoom Length (m) neL mooB66 gth (m)

Jib Length (m) neL biJ9131 gth (m)Offset Angle (deg.) Offset Angle (deg.)

Working Radius (m) Working Radius (m)12 14.8m x 15.1m x 12

m5.61t0.51 t0.03 41 x 16.9m x 1416 30.0 15.0 19.1m x 61t0.51 t7.42

81 0.51 4.42 t6.31 0.51 0.03 8120 30.0 15.0 13.5 23.9 15.0 22.7m x 2022 30.0 15.0 13.1 23.4 15.0 10.2t 2224 30.0 15.0 12.7 23.0 15.0 10.0 2426 30.0 15.0 12.3 22.5 15.0 9.7 2628 29.3 15.0 12.0 22.1 15.0 9.4 2830 27.9 15.0 11.7 21.7 15.0 9.1 3032 26.7 15.0 11.4 21.3 15.0 8.9 3234 25.6 15.0 11.1 20.9 15.0 8.6 3436 24.5 15.0 10.8 20.5 15.0 8.4 3638 23.6 15.0 10.6 20.0 15.0 8.2 3840 22.7 15.0 10.4 19.2 15.0 8.0 4042 21.9 15.0 10.2 18.5 15.0 7.8 4244 21.0 15.0 10.0 17.9 15.0 7.6 4446 19.2 15.0 9.8 17.2 15.0 7.5 4648 17.6 15.0 9.6 16.7 15.0 7.3 4850 16.1 15.0 9.5 16.1 15.0 7.2 5052 14.7 14.7 9.3 15.6 15.0 7.1 5254 13.4 13.4 9.2 14.4 14.4 6.9 5456 12.3 12.3 9.1 13.2 13.2 6.8 5658 11.2 11.2 8.9 12.1 12.1 6.7 5860 10.2 10.2 8.8 11.1 11.1 6.6 6062 9.3 9.3 8.7 10.2 10.2 6.5 6264 8.4 8.4 8.7 9.3 9.3 6.4 6466 7.6 7.6 8.0 8.5 8.5 6.4 6668 6.8 6.8 7.2 7.7 7.7 6.3 6870 6.1 6.1 6.4 7.0 7.0 6.2 7072 5.5 5.5 5.7 6.3 6.3 6.2 7274 72.6m x 73.4m x 73.7m x 5.7 5.7 6.1 7476 5.3t 5.0t 5.0t 5.1 5.1 5.4 7678 76.3m x 76.3m x 77.3m x 7880 5.0t 5.0t 5.0t 80

No. of part line 2 1 1 2 1 1 No. of part line

03010301

* For notes about the table above, refer to page 25.

Page 31: HYDRAULIC CRAWLER CRANE · SCX3500-3 SPECIFICATIONS Specifications Model CUMMINS QSL9 Type 4-cycle, water-cooled,Direct-injection,Turbo-charger Diesel engine Displacement 8.9 Liters

31

SpecificationsGross Rated Load Table

SPECIFICATIONS SCX3500-3

■Crane Jib (Rear end Radius: Standard)

Unit tonBoom Length (m) neL mooB66 gth (m)

Jib Length (m) neL biJ731352 gth (m)Offset Angle (deg.) Offset Angle (deg.)

Working Radius (m) Working Radius (m)16 18.2m x 18.6m x 16

m3.02t0.51 t9.81 81 x 1802t8.31 0.51 5.81 0222 8.8 5.31 0.51 1.81 22

24 17.7 15.0 26.3m x 42 7.8 2.31 26 17.3 15.0 7.9t 12.9 29.9m x 8.5 2628 16.8 15.0 7.7 12.6 7.3t 8.3 2830 16.4 15.0 7.4 12.2 7.3 8.0 3032 16.0 15.0 7.2 11.9 7.1 7.7 3234 15.6 15.0 7.0 11.6 6.9 7.5 3436 15.2 15.0 6.8 11.2 6.7 7.2 3638 14.8 14.8 6.6 10.9 6.5 7.0 3840 14.4 14.4 6.4 10.7 6.3 6.8 4042 14.1 14.1 6.3 10.4 6.2 6.6 4244 13.7 13.7 6.1 10.1 6.0 6.4 4446 13.4 13.4 6.0 9.9 5.9 6.2 4648 13.1 13.1 5.8 9.7 5.7 6.0 4850 12.8 12.8 5.7 9.5 5.6 5.9 5052 12.5 12.5 5.6 9.3 5.5 5.7 5254 12.2 12.2 5.5 9.1 5.3 5.6 5456 12.0 12.0 5.3 8.9 5.2 5.4 5658 11.8 11.8 5.2 8.7 5.1 5.3 5860 11.5 11.5 5.2 8.5 5.0 5.2 60

26 1.5 4.8 1.5 0.11 0.11 26 m0.36 2.8 0.5 1.01 1.01 46 x 64

66t0.5 1.8 2.9 2.9 6686 9.7 5.8 5.8 8607 8.7 7.7 7.7 0727 7.7 1.7 1.7 2747 4.7 4.6 4.6 4767 8.6 8.5 8.5 6787 2.6 2.5 2.5 87

80 78.8m x 78.8m x 08 6.5 28 1.5 t0.5 t0.5 28

84 82.4m x 8486 68t0.5

No. of part line 2 1 1 1 1 1 No. of part line

30 10010301

* For notes about the table above, refer to page 25.

Page 32: HYDRAULIC CRAWLER CRANE · SCX3500-3 SPECIFICATIONS Specifications Model CUMMINS QSL9 Type 4-cycle, water-cooled,Direct-injection,Turbo-charger Diesel engine Displacement 8.9 Liters

32

SpecificationsGross Rated Load Table

SPECIFICATIONSSCX3500-3

■Crane Jib (Rear end Radius: Standard)

Unit tonBoom Length (m) neL mooB27 gth (m)

Jib Length (m) neL biJ9131 gth (m)Offset Angle (deg.) Offset Angle (deg.)

Working Radius (m) Working Radius (m)12 15.5m x 15.8m x 12

m2.71t0.51 t0.03 41 x 17.5m x 1416 30.0 15.0 19.8m x 61t0.51 t9.42

81 0.51 7.42 t6.31 0.51 0.03 8120 30.0 15.0 13.6 24.2 15.0 23.4m x 2022 30.0 15.0 13.2 23.7 15.0 10.1t 2224 30.0 15.0 12.8 23.2 15.0 10.1 2426 30.0 15.0 12.5 22.8 15.0 9.8 2628 30.0 15.0 12.1 22.3 15.0 9.5 2830 29.0 15.0 11.8 21.9 15.0 9.2 3032 27.7 15.0 11.6 21.4 15.0 9.0 3234 26.6 15.0 11.3 21.1 15.0 8.7 3436 25.6 15.0 11.0 20.7 15.0 8.5 3638 24.6 15.0 10.8 20.4 15.0 8.3 3840 23.7 15.0 10.6 20.0 15.0 8.1 4042 22.0 15.0 10.4 19.3 15.0 8.0 4244 20.0 15.0 10.2 18.6 15.0 7.8 4446 18.2 15.0 10.0 18.0 15.0 7.6 4648 16.5 15.0 9.8 17.4 15.0 7.5 4850 15.0 15.0 9.7 16.0 15.0 7.3 5052 13.6 13.6 9.5 14.6 14.6 7.2 5254 12.4 12.4 9.4 13.4 13.4 7.1 5456 11.2 11.2 9.2 12.2 12.2 6.9 5658 10.1 10.1 9.1 11.1 11.1 6.8 5860 9.1 9.1 9.0 10.1 10.1 6.7 6062 8.2 8.2 8.8 9.1 9.1 6.6 6264 7.3 7.3 7.9 8.2 8.2 6.5 6466 6.5 6.5 7.0 7.4 7.4 6.5 6668 5.8 5.8 6.2 6.7 6.7 6.4 6870 5.1 5.1 5.5 5.9 5.9 6.3 7072 70.2m x 70.2m x 71.2m x 5.3 5.3 5.9 7274 5.0t 5.0t 5.0t 72.8m x 72.8m x 5.2 7476 5.0t 5.0t 74.5m x 7678 5.0t 78

No. of part line 2 1 1 2 1 1 No. of part line

03010301

Unit tonBoom Length (m) neL mooB27 gth (m)

Jib Length (m) neL biJ731352 gth (m)Offset Angle (deg.) Offset Angle (deg.)

Working Radius (m) Working Radius (m)16 18.9m x 19.2m x 16

m9.02t0.51 t9.81 81 x 18 m6.22t8.31 0.51 7.81 02 x 20

22t8.8 7.31 0.51 3.81 2224 17.9 15.0 27.0m x 42 7.8 4.31

62 5.8 1.31 t8.7 0.51 5.71 6228 17.0 15.0 7.7 12.8 30.5m x 8.4 2830 16.6 15.0 7.5 12.4 7.3t 8.1 3032 16.2 15.0 7.3 12.1 7.1 7.9 3234 15.8 15.0 7.1 11.8 6.9 7.6 3436 15.5 15.0 6.9 11.5 6.7 7.4 3638 15.1 15.0 6.7 11.2 6.6 7.2 3840 14.7 14.7 6.5 10.9 6.4 6.9 4042 14.4 14.4 6.4 10.6 6.2 6.7 4244 14.1 14.1 6.2 10.4 6.1 6.6 4446 13.7 13.7 6.1 10.1 6.0 6.4 4648 13.5 13.5 5.9 9.9 5.8 6.2 4850 13.2 13.2 5.8 9.7 5.7 6.0 5052 12.9 12.9 5.7 9.5 5.6 5.9 5254 12.6 12.6 5.6 9.3 5.4 5.7 5456 12.3 12.3 5.4 9.1 5.3 5.6 5658 11.9 11.9 5.3 8.9 5.2 5.5 5860 10.9 10.9 5.3 8.8 5.1 5.3 6062 9.9 9.9 5.2 8.6 5.0 5.2 62

46 1.5 5.8 1.5 0.9 0.9 4666 0.5 3.8 0.5 2.8 2.8 6686 2.8 4.7 4.7 8607 8.7 7.6 7.6 0727 1.7 0.6 0.6 2747 4.6 4.5 4.5 47

76 75.3m x 75.3m x 67 8.5 87 2.5 t0.5 t0.5 87

80 78.6m x 8082 28t0.5

No. of part line 2 1 1 1 1 1 No. of part line

30 10010301

* For notes about the table above, refer to page 25.

Page 33: HYDRAULIC CRAWLER CRANE · SCX3500-3 SPECIFICATIONS Specifications Model CUMMINS QSL9 Type 4-cycle, water-cooled,Direct-injection,Turbo-charger Diesel engine Displacement 8.9 Liters

33

SpecificationsGross Rated Load Table

SPECIFICATIONS SCX3500-3

■Main Boom with Crane Jib (Rear end Radius: Standard)

1. The rated loads are determined according to EN13000 rating on the condition that the machine is stationed on firm, level ground. 2. To calculate the maximum load that can actually be lifted, deduct mass of all lifting accessories, such as boom hook and jib hook, from figures shown above. 3. The figures surrounded by bold lines are based on factors other than those which would cause a tipping condition. 4. Working radius is the horizontal distance from the swing center to the center of gravity of a lifted load. 5. The 145 ton counter weight and 25 ton lower weight are required for all capacities on these charts. 6. Figures described as OOm x OOt in the tables indicate "working radius" m x "rated load" ton. 7. Correlation between the number of reeved lines, maximum rated loads, hook mass are shown in the table below.

10. The rated total load when the operation being performed with the rear post support pendant attached is the value remaining when the value in chart below is deducted from the rated total load chart.

8. The necessary mass to lower the boom hook refers "Lowerable Boom Hook Mass" on page 10. 9. The necessary mass to lower the crane jib hook refers "Lowerable Crane Jib Hook Mass" on page 10.

Boom Length (m)Equivalent Mass (ton)

42 48 54 60 66 720.8 0.9 1.2 1.4 1.6 1.7

Maximum Rated Load (ton)13 falls 12 falls 11 falls 10 falls 9 falls 8 falls 7 falls 6 falls 2 falls3 falls4 falls5 falls 1 fall

HookCapacity

HookMass (ton)

180t100t45t15t

3.343.112.170.62

180---

170---

157---

144---

131---

118---

104100

--

9090--

7676--

6161--

-4645-

-3131-

---

15

Unit tonBoom Length (m) neL mooB24 gth (m)

Jib Length (m) neL biJ529131 gth (m)Offset angle (deg.) Offset angle (deg.)

Working Radius (m) Working Radius (m) 7.9 170.0 170.0 170.0 170.0 170.0 170.0 7.9

8 170.0 170.0 170.0 170.0 170.0 170.0 89 170.0 170.0 170.0 169.4 170.0 167.3 910 154.4 153.1 153.3 151.3 152.1 149.3 1012 126.5 125.4 125.4 123.7 124.2 122.0 1214 106.2 105.3 105.1 103.8 104.0 102.1 1416 90.9 90.1 89.8 88.7 88.7 87.1 1618 78.8 78.2 77.8 76.8 76.7 75.4 1820 69.2 68.6 68.1 67.3 67.1 65.9 2022 61.2 60.8 60.2 59.5 59.1 58.2 2224 54.6 54.0 53.5 52.7 52.1 50.9 2426 48.5 47.6 47.0 46.3 45.6 44.7 2628 43.0 42.2 41.5 40.9 40.2 39.4 2830 38.2 37.5 36.8 36.3 35.5 34.8 3032 34.1 33.5 32.7 32.3 31.4 30.8 3234 30.5 30.0 29.1 28.8 27.8 27.4 3436 27.3 26.8 25.9 25.7 24.6 24.3 3638 24.4 24.1 23.1 23.0 21.8 21.7 3840 38.6m x 38.6m x 38.6m x 38.6m x 38.6m x 38.6m x 4042 23.6t 23.3t 22.3t 22.2t 21.1t 20.9t 42

10 30 10 30 10 30

Unit tonBoom Length (m) neL mooB24 gth (m)

Jib Length (m) neL biJ7313 gth (m)Offset angle (deg.) Offset angle (deg.)

Working Radius (m) Working Radius (m)- 7.9m x 7.9m x 7.9m x -7 170.0t 170.0t 170.0t 78 170.0 170.0 170.0 89 169.1 165.1 167.8 910 150.8 147.2 149.5 1012 123.0 120.0 121.7 1214 102.8 100.4 101.5 1416 87.5 85.5 86.3 1618 75.5 73.8 74.3 1820 65.9 64.4 64.7 2022 58.0 56.5 56.7 2224 50.6 49.1 49.0 2426 44.2 42.9 42.6 2628 38.7 37.7 37.2 2830 34.0 33.2 32.6 3032 30.0 29.3 28.5 3234 26.4 25.9 25.0 3436 23.3 22.9 21.9 3638 20.5 20.3 19.1 3840 38.6m x 38.6m x 38.6m x 4042 19.7t 19.6t 18.3t 42

10 30 10

Page 34: HYDRAULIC CRAWLER CRANE · SCX3500-3 SPECIFICATIONS Specifications Model CUMMINS QSL9 Type 4-cycle, water-cooled,Direct-injection,Turbo-charger Diesel engine Displacement 8.9 Liters

34

SpecificationsGross Rated Load Table

SPECIFICATIONSSCX3500-3

■Main Boom with Crane Jib (Rear end Radius: Standard)

Unit tonBoom Length (m) neL mooB84 gth (m)

Jib Length (m) neL biJ529131 gth (m)Offset angle (deg.) Offset angle (deg.)

Working Radius (m) Working Radius (m)7 8.6m x 8.6m x 8.6m x 8.6m x 8.6m x 8.6m x 78 157.0t 157.0t 157.0t 157.0t 157.0t 157.0t 89 157.0 157.0 157.0 157.0 157.0 157.0 910 153.8 152.4 152.7 150.6 151.5 148.7 1012 125.8 124.7 124.7 123.1 123.6 121.3 1214 105.5 104.6 104.5 103.1 103.4 101.5 1416 90.2 89.4 89.2 88.0 88.1 86.5 1618 78.2 77.5 77.2 76.2 76.1 74.7 1820 68.5 67.9 67.5 66.6 66.5 65.3 2022 60.5 60.1 59.6 58.8 58.6 57.5 2224 53.9 53.3 52.6 51.7 51.3 50.0 2426 47.4 46.9 46.1 45.3 44.8 43.7 2628 41.9 41.5 40.7 40.0 39.4 38.4 2830 37.2 36.8 36.0 35.4 34.7 33.9 3032 33.1 32.8 31.9 31.4 30.6 29.9 3234 29.5 29.2 28.3 27.9 27.1 26.5 3436 26.3 26.1 25.2 24.8 23.9 23.5 3638 23.5 23.3 22.4 22.1 21.1 20.8 3840 21.0 20.9 19.8 19.6 18.6 18.4 4042 18.7 18.7 17.6 17.5 16.4 16.2 4244 43.8m x 43.8m x 43.8m x 43.8m x 43.8m x 43.8m x 4446 16.9t 16.8t 15.8t 15.7t 14.6t 14.5t 46

10 30 10 30 10 30

Unit tonBoom Length (m) neL mooB84 gth (m)

Jib Length (m) neL biJ7313 gth (m)Offset angle (deg.) Offset angle (deg.)

Working Radius (m) Working Radius (m)7 8.6m x 8.6m x 8.6m x 78 157.0t 157.0t 157.0t 89 157.0 157.0 157.0 910 150.3 146.6 149.0 1012 122.4 119.5 121.2 1214 102.3 99.8 101.1 1416 87.0 84.9 85.8 1618 75.0 73.2 73.9 1820 65.4 63.8 64.3 2022 57.5 55.6 56.0 2224 49.9 48.2 48.4 2426 43.5 42.0 42.0 2628 38.0 36.8 36.6 2830 33.4 32.3 32.0 3032 29.3 28.4 27.9 3234 25.8 25.0 24.4 3436 22.6 22.0 21.3 3638 19.9 19.4 18.5 3840 17.4 17.0 16.1 4042 15.2 14.9 13.9 4244 43.8m x 43.8m x 43.8m x 4446 13.4t 13.2t 12.1t 46

30 1010

* For notes about the table above, refer to page 33.

Page 35: HYDRAULIC CRAWLER CRANE · SCX3500-3 SPECIFICATIONS Specifications Model CUMMINS QSL9 Type 4-cycle, water-cooled,Direct-injection,Turbo-charger Diesel engine Displacement 8.9 Liters

35

SpecificationsGross Rated Load Table

SPECIFICATIONS SCX3500-3

■Main Boom with Crane Jib (Rear end Radius: Standard)

Unit tonBoom Length (m) neL mooB45 gth (m)

Jib Length (m) neL biJ529131 gth (m)Offset angle (deg.) Offset angle (deg.)

Working Radius (m) Working Radius (m)8 9.3m x 9.3m x 9.3m x 9.3m x 9.3m x 9.3m x 89 131.0t 131.0t 131.0t 131.0t 131.0t 131.0t 910 131.0 131.0 131.0 131.0 131.0 131.0 1012 125.3 124.2 124.3 122.6 123.2 120.9 1214 105.1 104.1 104.1 102.6 103.0 101.0 1416 89.7 88.9 88.7 87.5 87.7 86.0 1618 77.7 77.0 76.7 75.7 75.7 74.3 1820 68.0 67.4 67.1 66.1 66.1 64.8 2022 60.0 59.5 59.1 58.3 58.2 56.7 2224 53.1 52.4 51.8 50.9 50.6 49.2 2426 46.6 46.1 45.4 44.5 44.1 43.0 2628 41.1 40.6 39.9 39.2 38.7 37.6 2830 36.4 36.0 35.2 34.6 34.0 33.1 3032 32.3 31.9 31.1 30.6 29.9 29.1 3234 28.7 28.4 27.6 27.1 26.4 25.7 3436 25.6 25.3 24.4 24.0 23.2 22.6 3638 22.7 22.5 21.6 21.2 20.5 19.9 3840 20.2 20.0 19.1 18.8 18.0 17.5 4042 17.9 17.8 16.8 16.6 15.7 15.4 4244 15.9 15.8 14.8 14.6 13.7 13.4 4446 14.0 13.9 13.0 12.8 11.8 11.6 4648 12.3 12.3 11.3 11.2 10.2 10.1 4850 49.0m x 49.0m x 49.0m x 49.0m x 49.0m x 49.0m x 5052 11.6t 11.5t 10.5t 10.4t 9.4t 9.3t 52

10 30 10 30 10 30

Unit tonBoom Length (m) neL mooB45 gth (m)

Jib Length (m) neL biJ7313 gth (m)Offset angle (deg.) Offset angle (deg.)

Working Radius (m) Working Radius (m)8 9.3m x 9.3m x 9.3m x 89 131.0t 131.0t 131.0t 910 131.0 131.0 131.0 1012 122.1 119.0 120.9 1214 101.9 99.4 100.8 1416 86.6 84.5 85.5 1618 74.7 72.8 73.6 1820 65.1 63.4 64.0 2022 56.9 54.9 55.5 2224 49.2 47.5 47.8 2426 42.8 41.3 41.4 2628 37.4 36.0 36.0 2830 32.7 31.6 31.4 3032 28.7 27.7 27.4 3234 25.1 24.2 23.8 3436 22.0 21.2 20.7 3638 19.2 18.6 18.0 3840 16.8 16.2 15.5 4042 14.5 14.1 13.3 4244 12.5 12.2 11.3 4446 10.7 10.4 9.5 4648 9.0 8.9 7.8 4850 49.0m x 49.0m x 49.0m x 5052 8.3t 8.1t 7.1t 52

30 1010

* For notes about the table above, refer to page 33.

Page 36: HYDRAULIC CRAWLER CRANE · SCX3500-3 SPECIFICATIONS Specifications Model CUMMINS QSL9 Type 4-cycle, water-cooled,Direct-injection,Turbo-charger Diesel engine Displacement 8.9 Liters

36

SpecificationsGross Rated Load Table

SPECIFICATIONSSCX3500-3

■Main Boom with Crane Jib (Rear end Radius: Standard)

Unit tonBoom Length (m) neL mooB06 gth (m)

Jib Length (m) neL biJ529131 gth (m)Offset angle (deg.) Offset angle (deg.)

Working Radius (m) Working Radius (m)8 9.9m x 9.9m x 9.9m x 9.9m x 9.9m x 9.9m x 89 118.0t 118.0t 118.0t 118.0t 118.0t 118.0t 910 118.0 118.0 118.0 118.0 118.0 118.0 1012 117.7 117.5 117.2 116.8 116.6 116.1 1214 104.4 103.4 103.4 102.0 102.4 100.4 1416 89.0 88.2 88.1 86.8 87.1 85.4 1618 77.0 76.3 76.1 75.0 75.1 73.6 1820 67.3 66.7 66.4 65.5 65.5 64.1 2022 59.3 58.8 58.5 57.4 57.3 55.7 2224 52.1 51.4 50.9 49.8 49.6 48.2 2426 45.6 45.0 44.4 43.5 43.2 42.0 2628 40.1 39.6 38.9 38.1 37.8 36.7 2830 35.4 34.9 34.3 33.5 33.1 32.1 3032 31.3 30.9 30.2 29.5 29.0 28.2 3234 27.7 27.4 26.6 26.1 25.5 24.7 3436 24.6 24.2 23.5 23.0 22.3 21.7 3638 21.8 21.5 20.7 20.2 19.6 19.0 3840 19.2 19.0 18.2 17.8 17.1 16.5 4042 17.0 16.8 15.9 15.6 14.8 14.4 4244 14.9 14.7 13.9 13.6 12.8 12.4 4446 13.1 12.9 12.0 11.8 11.0 10.6 4648 11.4 11.2 10.3 10.1 9.3 9.0 4850 9.8 9.7 8.8 8.6 7.7 7.5 5052 8.4 8.3 7.4 7.3 6.4 6.2 5254 7.1 7.1 6.1 6.0 5.1 5.0 5456 54.2m x 54.2m x 54.2m x 54.2m x 54.2m x 56

85t0.5 t9.5 t0.6 t9.6 t0.7 85

10 30 10 30 10 30

Unit tonBoom Length (m) neL mooB06 gth (m)

Jib Length (m) neL biJ7313 gth (m)Offset angle (deg.) Offset angle (deg.)

Working Radius (m) Working Radius (m)8 9.9m x 9.9m x 9.9m x 89 118.0t 118.0t 118.0t 910 118.0 118.0 118.0 1012 116.1 115.4 115.5 1214 101.3 98.7 100.2 1416 86.1 83.8 85.0 1618 74.1 72.2 73.0 1820 64.5 62.8 63.4 2022 56.0 53.9 54.7 2224 48.4 46.5 47.0 2426 42.0 40.3 40.6 2628 36.5 35.1 35.2 2830 31.9 30.6 30.6 3032 27.8 26.7 26.6 3234 24.3 23.3 23.1 3436 21.2 20.3 19.9 3638 18.4 17.6 17.2 3840 15.9 15.2 14.7 4042 13.7 13.1 12.5 4244 11.7 11.2 10.5 4446 9.8 9.4 8.7 4648 8.2 7.8 7.0 4850 6.7 6.4 5.5 5052 5.3 5.1 50.7m x 5254 52.4m x 52.1m x 5.0t 54

65t0.5 t0.5 65

30 1010

* For notes about the table above, refer to page 33.

Page 37: HYDRAULIC CRAWLER CRANE · SCX3500-3 SPECIFICATIONS Specifications Model CUMMINS QSL9 Type 4-cycle, water-cooled,Direct-injection,Turbo-charger Diesel engine Displacement 8.9 Liters

37

SpecificationsGross Rated Load Table

SPECIFICATIONS SCX3500-3

■Main Boom with Crane Jib (Rear end Radius: Standard)

Unit tonBoom Length (m) neL mooB66 gth (m)

Jib Length (m) neL biJ529131 gth (m)Offset angle (deg.) Offset angle (deg.)

Working Radius (m) Working Radius (m)9 10.6m x 10.6m x 10.6m x 10.6m x 10.6m x 10.6m x 910 93.1t 92.8t 92.5t 92.2t 92.0t 91.5t 1012 90.9 90.7 90.4 90.0 89.8 89.3 1214 88.0 87.7 87.4 87.1 86.9 86.4 1416 85.1 84.9 84.6 84.2 84.0 83.4 1618 76.4 75.6 75.2 73.9 74.0 72.2 1820 66.8 66.2 65.9 64.8 64.7 63.1 2022 58.8 58.3 57.9 56.6 56.6 55.0 2224 51.3 50.6 50.1 49.1 49.0 47.5 2426 44.8 44.2 43.7 42.7 42.5 41.2 2628 39.3 38.8 38.2 37.4 37.1 35.9 2830 34.6 34.1 33.5 32.8 32.4 31.4 3032 30.5 30.1 29.4 28.8 28.3 27.4 3234 27.0 26.6 25.9 25.3 24.8 24.0 3436 23.8 23.5 22.7 22.2 21.7 20.9 3638 21.0 20.7 19.9 19.5 18.9 18.2 3840 18.5 18.2 17.4 17.0 16.4 15.8 4042 16.2 16.0 15.2 14.8 14.1 13.6 4244 14.2 14.0 13.1 12.8 12.1 11.6 4446 12.3 12.1 11.3 11.0 10.3 9.9 4648 10.6 10.4 9.6 9.4 8.6 8.2 4850 9.1 8.9 8.1 7.8 7.1 6.7 5052 7.6 7.5 6.6 6.5 5.6 5.4 5254 6.3 6.2 5.3 5.2 52.9m x 52.6m x 5456 5.1 5.0 54.5m x 54.3m x 5.0t 5.0t 5658 56.1m x 85t0.5 t0.5 60 5.0t 60

10 30 10 30 10 30

Unit tonBoom Length (m) neL mooB66 gth (m)

Jib Length (m) neL biJ7313 gth (m)Offset angle (deg.) Offset angle (deg.)

Working Radius (m) Working Radius (m)9 10.6m x 10.6m x 10.6m x 910 91.5t 90.8t 90.9t 1012 89.3 88.6 88.7 1214 86.3 85.7 85.7 1416 83.4 81.4 82.6 1618 72.6 70.3 71.2 1820 63.4 61.3 62.0 2022 55.4 53.2 54.1 2224 47.7 45.8 46.4 2426 41.3 39.6 40.0 2628 35.9 34.4 34.6 2830 31.2 29.9 30.0 3032 27.2 26.0 26.0 3234 23.6 22.6 22.5 3436 20.5 19.6 19.3 3638 17.8 16.9 16.6 3840 15.3 14.5 14.1 4042 13.0 12.3 11.9 4244 11.0 10.4 9.9 4446 9.2 8.7 8.1 4648 7.5 7.1 6.4 4850 6.0 5.6 49.8m x 5052 51.4m x 50.9m x 5.0t 52

45t0.5 t0.5 45

30 1010

* For notes about the table above, refer to page 33.

Page 38: HYDRAULIC CRAWLER CRANE · SCX3500-3 SPECIFICATIONS Specifications Model CUMMINS QSL9 Type 4-cycle, water-cooled,Direct-injection,Turbo-charger Diesel engine Displacement 8.9 Liters

38

SpecificationsGross Rated Load Table

SPECIFICATIONSSCX3500-3

■Main Boom with Crane Jib (Rear end Radius: Standard)

Unit tonBoom Length (m) neL mooB27 gth (m)

Jib Length (m) neL biJ529131 gth (m)Offset angle (deg.) Offset angle (deg.)

Working Radius (m) Working Radius (m)9 11.3m x 11.3m x 11.3m x 11.3m x 11.3m x 11.3m x 910 71.3t 71.1t 70.8t 70.4t 70.3t 69.7t 1012 70.4 70.2 69.9 69.5 69.3 68.8 1214 67.9 67.7 67.4 67.0 66.8 66.3 1416 65.5 65.3 65.0 64.6 64.4 63.9 1618 63.1 62.9 62.6 62.3 62.0 61.6 1820 60.9 60.7 60.4 60.0 59.8 59.4 2022 57.0 56.3 55.9 54.9 54.7 53.3 2224 50.0 49.3 48.9 47.8 47.7 46.2 2426 43.6 42.9 42.4 41.5 41.3 40.0 2628 38.1 37.5 37.0 36.1 35.9 34.7 2830 33.4 32.9 32.3 31.5 31.2 30.1 3032 29.3 28.8 28.2 27.5 27.2 26.2 3234 25.7 25.3 24.7 24.0 23.6 22.7 3436 22.6 22.2 21.5 21.0 20.5 19.7 3638 19.8 19.4 18.7 18.2 17.7 17.0 3840 17.3 17.0 16.2 15.8 15.2 14.6 4042 15.0 14.7 14.0 13.6 13.0 12.4 4244 13.0 12.7 12.0 11.6 11.0 10.4 4446 11.1 10.9 10.1 9.8 9.1 8.6 4648 9.4 9.2 8.4 8.1 7.5 7.0 4850 7.9 7.7 6.9 6.6 5.9 5.5 5052 6.5 6.3 5.5 5.2 51.2m x 50.7m x 5254 5.1 5.0 52.7m x 52.3m x 5.0t 5.0t 5456 54.1m x 65t0.5 t0.5 58 5.0t 58

10 30 10 30 10 30

Unit tonBoom Length (m) neL mooB27 gth (m)

Jib Length (m) neL biJ7313 gth (m)Offset angle (deg.) Offset angle (deg.)

Working Radius (m) Working Radius (m)9 11.3m x 11.3m x 11.3m x 910 69.7t 69.1t 69.2t 1012 68.8 68.1 68.2 1214 66.3 65.6 65.7 1416 63.8 63.2 63.3 1618 61.5 60.9 60.9 1820 59.2 58.6 58.6 2022 53.5 51.7 52.2 2224 46.5 44.6 45.3 2426 40.1 38.4 38.9 2628 34.7 33.2 33.5 2830 30.1 28.7 28.9 3032 26.0 24.8 24.9 3234 22.5 21.4 21.4 3436 19.4 18.4 18.3 3638 16.6 15.7 15.5 3840 14.1 13.3 13.0 4042 11.9 11.2 10.8 4244 9.9 9.2 8.8 4446 8.1 7.5 7.0 4648 6.4 5.9 5.3 4850 49.8m x 49.2m x 48.4m x 5052 5.0t 5.0t 5.0t 52

30 1010

* For notes about the table above, refer to page 33.

Page 39: HYDRAULIC CRAWLER CRANE · SCX3500-3 SPECIFICATIONS Specifications Model CUMMINS QSL9 Type 4-cycle, water-cooled,Direct-injection,Turbo-charger Diesel engine Displacement 8.9 Liters

39

Tower SpecificationsDimensions and Specifications

SPECIFICATIONS SCX3500-3

104409265

2400

0 to

600

00

88°60°

1500

74°15°

2200

24000 to 60000

8750

1500

R6800R8300

Rear end Radius:ShortRear end Radius:Standard

Dimensions and Specifications

Tower Specifications

Tower SpecificationsMax. Lifting Load × Working Radius t × m 100 × 12.4

Tower Length m 24 to 60Tower Jib Length m 24 to 60Tower with Tower Jib Longest Length m 60 + 60

Engine Model CUMMINS QSL9(Stage III A/Tier 3)

Engine Rated Output Power

kW/min-1

(ps/rpm)280/2,000

(380/2,000)

Ground Contact Pressure kPa (kgf/cm²)152 (1.55)

(Tower with Tower Jib Longest Length)

Overall Operating Weight tApproximately 360

(Tower with Tower Jib Longest Length)

NOTE : Data is expressed in SI units followed by conventional units in ( ).

Page 40: HYDRAULIC CRAWLER CRANE · SCX3500-3 SPECIFICATIONS Specifications Model CUMMINS QSL9 Type 4-cycle, water-cooled,Direct-injection,Turbo-charger Diesel engine Displacement 8.9 Liters

40

Tower SpecificationsTower Standard Configurations

SPECIFICATIONSSCX3500-3

Tower Standard Configurations

Tower JibTower Jib

Length(m)

Tower Jib Configurations

24 LB8 L9 LT7

9 6.47.8

30 LB8 L6 L9 LT7

6 9 6.47.8

36 LB8 L6 L9 LT7

67.8 9 6.4

L6

6

42 LB8 L6 L9 LT7

67.8 9 6.4

L6

6

L6

6

48 LB8 L6 L9 LT7

6 9 6.47.8

L9

9

L9

9

54 LB8 L6 L9 LT7

67.8 9 6.4

L6

6

L9

9

L9

9

60LB8 L6 L9 LT7

67.8 9 6.4

L6

6

L6

6

L9

9

L9

9

  

Tower BoomTower Boom

Length(m)

Tower Boom Configurations

24HB9.5 HR7

7 6

H6B HT1.5

7 3.1

32.5

30HB9.5 HR7

7 6

H6B HT1.5H6

6

7 6

32.5

3.1

36HB9.5 HR7

7 6

H6B HT1.5H6

6

H6

6

7 66

32.5

3.1

42HB9.5 HR7

7 699

7 99

H6BH9 H9 HT1.5

32.5

3.1

48HB9.5 HR7 H6

7 6 699

7 6 99

H6BH9 H9 HT1.5

32.5

3.1

54HB9.5 HR7 H6

7 6 699

H6

6

7 6 996

H6BH9 H9 HT1.5

32.5

3.1

60HB9.5 HR7

7 699

H6BH9 H9 HT1.5HB9.5 HR7

7 699

H6BH9 H9

HB9.5 HR7

7 69999

H6BH9 H9 H9 H9 HT1.5

6

H6

6

H6

6

7 997 99

7 9999

66 6

H6

32.5

32.5

3.1

3.1

Dimensions Not Shown In The Figure

Symbols Tower Boom Length(m) Note

HB9.5 9.5 Boom BaseHH1.5 1.5 Hammer HeadHT1.5 1.5 Boom Top

H6 6 Boom InsertH6B 6 Boom Insert BH9 9 Boom Insert

HR7 7 Reducer

Dimensions Not Shown In The Figure

Symbols Tower Jib Length(m) Note

LB8 8 Tower/Luffing Jib BaseL6 6 Tower/Luffing Jib InsertL9 9 Tower/Luffing Jib InsertLT7 7 Tower/Luffing Jib Top

Symbols Length (m)

Rope Diameter

(mm)Imprint

6 5.6 48 □・△・48・5.6・69 8.6 48 □・△・48・8.6・6

NOTE: Check the pendant rope with referring to the imprints on the rope end.

Imprint

Dimensions Not Shown In The Figure

Symbols Bar Pendant Length(m) Note

2.5 2.5 0.5m + 0.3m + 1.3m (Spreader) + 0.4m

3 3 0.4m + 1.2m + 1.0m + 0.4m* For rear end radius: short radius not use

6 6 5.6m + 0.4m (Link)7 7 6.6m + 0.4m (Link)9 9 8.6m + 0.4m (Link)

3.1 3.1 0.4m (Link) + 2.3m + 0.4m (Link)

Dimensions Not Shown In The Figure

Symbols Pendant Rope Length(m) Note

6 6 5.6m + 0.4m (Link)9 9 8.6m + 0.4m (Link)

6.4 6.4 0.45m (Link) + 5.6m (Bar Pendant)+ 0.35m (Link)

Page 41: HYDRAULIC CRAWLER CRANE · SCX3500-3 SPECIFICATIONS Specifications Model CUMMINS QSL9 Type 4-cycle, water-cooled,Direct-injection,Turbo-charger Diesel engine Displacement 8.9 Liters

41

Tower SpecificationsRestriction of Hook Usage

SPECIFICATIONS SCX3500-3

Tower Jib Installable Tower Length (Rear end Radius: Standard)

Jib Length (m)Tower Length

24 30 36 42 48 54 6024 ○ ○ ○ ○ ○ ○ ×30 ○ ○ ○ ○ ○ ○ ○36 ○ ○ ○ ○ ○ ○ ○42 ○ ○ ○ ○ ○ ○ ○48 ○ ○ ○ ○ ○ ○ ○54 ○ ○ ○ ○ ○ ○ △60 ○ ○ ○ ○ ○ ○ △

Tower Jib Installable Tower Length (Rear end Radius: Short)

Jib Length (m)Tower Length

24 30 36 42 48 54 6024 ○ ○ ○ ○ ○ × ×30 ○ ○ ○ ○ ○ ○ ×36 ○ ○ ○ ○ ○ ○ ×42 ○ ○ ○ ○ ○ ○ ×48 ○ ○ ○ ○ ○ ○ ×54 ○ ○ ○ ○ ○ △ ×60 ○ ○ ○ ○ ○ △ ×

The symbols in the table are as below. ○ : Attachable

× : Not Attachable

△ : Removal of Sheave Lock Required

The symbols in the table are as below. ○ : Attachable

× : Not Attachable

△ : Removal of Sheave Lock Required

Restriction of Hook Usage

Tower Length 24 30Jib Length 24 30 36 42 48 54 60 24 30 36 42 48 54 60100t Hook ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○45t Hook ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○15t Hook × × × ○ ○ ○ ○ × × × ○ ○ ○ ○

Tower Length 36 42Jib Length 24 30 36 42 48 54 60 24 30 36 42 48 54 60100t Hook ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○45t Hook ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○15t Hook × × × ○ ○ ○ ○ × × × ○ ○ ○ ○

Tower Length 48 54Jib Length 24 30 36 42 48 54 60 24 30 36 42 48 54 60100t Hook ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○45t Hook × ○ ○ ○ ○ ○ ○ × ○ ○ ○ ○ ○ ○15t Hook × × × ○ ○ ○ ○ × × × ○ ○ ○ ○

Tower Length 60Jib Length 30 36 42 48 54 60100t Hook ○ ○ ○ ○ ○ ○45t Hook × ○ ○ ○ ○ ○15t Hook × × ○ ○ ○ ○

The symbols in the table are as below.○:usable

×:unusable 

The hooks which can be used as a jib hook, when there is and when there isn’t an aux. sheave hook, are listed in the following table.Using the unusable hook cause the jib to swing.

In the aux. sheave hook, a 45t hook or 15t hook can be used in all combinations.

Page 42: HYDRAULIC CRAWLER CRANE · SCX3500-3 SPECIFICATIONS Specifications Model CUMMINS QSL9 Type 4-cycle, water-cooled,Direct-injection,Turbo-charger Diesel engine Displacement 8.9 Liters

42

Tower SpecificationsLowerable Jib Hook Mass

SPECIFICATIONSSCX3500-3

Lowerable Jib Hook Mass

Tower Length + Jib Length (m)No. of Reeved Lines

1 fall 2 falls 3 falls 4 falls 5 falls 6 falls 7 falls48 0.6 2.1 2.1 3.1 3.1 3.1 3.154 0.6 2.1 2.1 3.1 3.1 3.1 3.160 0.6 2.1 2.1 3.1 3.1 3.1 3.166 0.6 2.1 2.1 3.1 3.1 3.1 3.172 0.6 2.1 2.1 3.1 3.1 3.1 -78 0.6 2.1 2.1 3.1 3.1 - -84 0.6 2.1 2.1 3.1 3.1 - -90 0.6 2.1 2.1 3.1 - - -96 0.7 2.1 2.1 3.1 - - -102 0.7 2.1 2.1 - - - -108 0.7 2.1 2.1 - - - -114 0.8 2.1 2.2 - - - -120 0.8 2.1 - - - - -

Unit:ton

Lowerable Tower Head Hook Mass

Tower Length (m)No. of Reeved Lines

1 fall 2 falls 3 falls 4 falls 5 falls 6 falls 7 falls24 0.6 2.1 2.1 3.1 3.1 3.1 3.130 0.6 2.1 2.1 3.1 3.1 3.1 3.136 0.6 2.1 2.1 3.1 3.1 3.1 3.142 0.6 2.1 2.1 3.1 3.1 3.1 3.148 0.6 2.1 2.1 3.1 3.1 3.1 3.154 0.6 2.1 2.1 3.1 3.1 3.1 3.160 0.6 2.1 2.1 3.1 3.1 3.1 3.1

Unit:ton

Page 43: HYDRAULIC CRAWLER CRANE · SCX3500-3 SPECIFICATIONS Specifications Model CUMMINS QSL9 Type 4-cycle, water-cooled,Direct-injection,Turbo-charger Diesel engine Displacement 8.9 Liters

43

Tower SpecificationsWorking Ranges

SPECIFICATIONS SCX3500-3

Working Ranges

■Rear end Radius: Standard

5

10

15

20

25

30

35

40

45

50

55

60

65

5 10 15 20 25 30 35 40 45 500 70656055

80

75

70

75 80

110

105

115

100

95

90

85

120

125

130 74° 60°

15°

15°

30°

45°

1.5m

3.15

m

80°70°60°

88°

6.0m

6.2m

4.4m

48 mJib

42 mJib

36 mJib

24 mJib

60 m Tower

100t Hook

Working Radius (m)

45t Hook 15t Hook

24 mTower

30 mJib

54 mJib

60 m Jib

Height Above G

round

(m)

Page 44: HYDRAULIC CRAWLER CRANE · SCX3500-3 SPECIFICATIONS Specifications Model CUMMINS QSL9 Type 4-cycle, water-cooled,Direct-injection,Turbo-charger Diesel engine Displacement 8.9 Liters

44

Tower SpecificationsWorking Ranges

SPECIFICATIONSSCX3500-3

■Rear end Radius: Short

5

10

15

20

25

30

35

40

45

50

55

60

65

5 10 15 20 25 30 35 40 45 500 70656055

80

75

70

75 80 85

110

105

115

100

95

90

85

120

125

130 74° 60°

15°

15°

30°

45°

1.5m

3.15

m

60°70°

80°88°

6.0m

6.2m

4.4m

60 mJib

54 mJib

48 mJib

42 mJib

36 mJib

30 mJib

24 mJib

24 mJib

54 mTower

24 mTower

Working Radius (m)

100t Hook 45t Hook 15t Hook

Height Above G

round

(m)

Page 45: HYDRAULIC CRAWLER CRANE · SCX3500-3 SPECIFICATIONS Specifications Model CUMMINS QSL9 Type 4-cycle, water-cooled,Direct-injection,Turbo-charger Diesel engine Displacement 8.9 Liters

45

Tower SpecificationsWorking Ranges

SPECIFICATIONS SCX3500-3

■Tower Head Hoisting (Rear end Radius: Standard)

5 10 15 20 25 30 35 40 45 500 70656055

35

40

45

50

55

60

65

70

75

80

85

90

30

100

95

5

10

15

20

25

105 60°83.5°

14°

24m

30m

36m

42m

48m

54m

60m

1.5m

3.15

m

6.0m

5.8m

5.6m

24m to 60m Jib

Working Radius (m)

100t Hook 45t Hook 15t Hook

Height Above G

round

(m)

30m to 48m Jib

Page 46: HYDRAULIC CRAWLER CRANE · SCX3500-3 SPECIFICATIONS Specifications Model CUMMINS QSL9 Type 4-cycle, water-cooled,Direct-injection,Turbo-charger Diesel engine Displacement 8.9 Liters

46

Tower SpecificationsGross Rated Load Table

SPECIFICATIONSSCX3500-3

Gross Rated Load Table

■Tower 24 m (Rear end Radius: Standard)

Unit tonBoom Length (m) neL mooB42 gth (m)

Jib Length (m) neL biJ0342 gth (m)Boom Angle (deg.) Boom Angle (deg.)Radius (m) Radius (m)

- 13.8m x -0.090.0011.21 t 12.1

412.980.39 4116 84.1 18.3m x 612.2818 76.9 85.8t 75.0 20.8m x 18

4.471.966.97 9.07 02 t 20221.170.461.37 9.56 22

24 58.6 67.2 26.1m x 429.567.9526 45.5 60.6 55.9t 56.0 60.6 29.5m x 2628 27.8m x 6.741.559.251.15 0.55 t 2830 33.7t 48.2 46.7 33.2m x 036.644.051.44

m3.1323 x 42.9 37.8t 239.244.648.438.8343 t 39.6 36.6 33.6m x 42.9 39.6 37.4m x 34

m5.5363 x 33.9 27.3t 37.5 36.8 32.2t 364.7383 t 31.6 37.1m x 34.3 31.5 38

m4.9304 x 31.6t 32.0 29.4 400.0324 t 41.3m x 27.6 42

44 30.7t 25.9 4446 45.2m x 4648 25.0t 48

80 06078806070888

1. The rated loads are determined according to EN13000 rating on the condition that the machine is stationed on firm, level ground.

Unit tonBoom Length (m) neL mooB42 gth (m)

Jib Length (m) neL biJ2463 gth (m)Boom Angle (deg.) Boom Angle (deg.)Radius (m) Radius (m)

12 15.5m x 1214 79.1t 17.2m x 14

9.965.77 61 t 16819.769.17 81

20 66.8 23.2m x 023.3622 61.8 64.4t 59.2 25.7m x 22

1.655.557.26 5.75 42 t 24626.559.159.85 8.35 62823.257.846.45 6.05 82

30 47.8 49.9 32.9m x 033.949.5432 45.3 45.9 40.7t 233.544.34

m2.638.142.149.83 4.24 2.04 43 x 342.538.832.931.63 3.93 2.33 63 t 36

38 26.7 36.7 33.6 41.6m x 830.331.633.6340 39.4m x 34.3 31.4 27.2t 048.037.338.0342 21.9t 29.1 29.4 26.8 25.7 31.6 28.8 45.7m x 42

m9.2444 x 27.6 25.2 20.9 29.6 27.0 23.2t 447.5264 t 26.0 23.7 45.2m x 27.9 25.4 23.0 46

m1.7484 x 22.3 17.8t 23.1 23.9 21.6 482.5205 t 21.1 48.7m x 22.6 20.4 50

m0.1525 x 21.1t 21.4 19.2 525.0245 t 52.9m x 18.2 54

56 20.8t 17.2 5658 56.8m x 5860 16.9t 60

88 80 70 60 88 80 70 60

2. To calculate the maximum load that can actually

3. The figures surrounded by

5. The 145 ton counter weight and 25 ton lower weight are required for all capacities on these charts.

9. The necessary mass to lower the hook refers "Lowerable Jib Hook Mass" on page 42.

HookCapacity

HookMass (ton) 7falls 6falls 5falls 4falls 3falls 2falls 1fall

100t 3.11 100 90 76 61 46 31 -45t 2.17 - - - - 45 31 -15t 0.62 - - - - - - 15

Maximum Rated Load (ton)

7. The usable hook when lifting tower jib is described on page 41. Using the unusable hook cause the jib to swing. 8. Correlation between the number of reeved lines, maximum rated loads, hook mass are shown in the table below.

bold lines are based on factors other than those which would cause a tipping condition.4. Working radius is the horizontal distance from the swing center to the center of gravity of a lifted load.

be lifted, deduct mass of all lifting accessories, such as hook, from figures shown above.

10. Be sure to attach the balance weight (420kg x 2) to the top jib when the jib length is 24m.

12. The gross rated load value of the jib with the sheave block the boom top is after 1.1 tons is deducted from the gross rated load of the jib.11. Remove the sheave block the boom top when using jib length 54 or 60 m for boom length 60 m.

6. Figures described as OOm x OOt in the tables indicate "working radius" m x "rated load" ton.

Page 47: HYDRAULIC CRAWLER CRANE · SCX3500-3 SPECIFICATIONS Specifications Model CUMMINS QSL9 Type 4-cycle, water-cooled,Direct-injection,Turbo-charger Diesel engine Displacement 8.9 Liters

47

Tower SpecificationsGross Rated Load Table

SPECIFICATIONS SCX3500-3

■Tower 24 m (Rear end Radius: Standard)

Unit tonBoom Length (m) neL mooB42 gth (m)

Jib Length (m) neL biJ4584 gth (m)Boom Angle (deg.) Boom Angle (deg.)Radius (m) Radius (m)

16 18.9m x 1618 62.4t 20.6m x 18

4.551.06 02 t 20228.253.65 22424.949.25 42

26 49.7 28.1m x 623.6428 47.0 49.4t 43.6 30.5m x 28

6.341.148.64 5.44 03 t 30238.149.834.44 0.24 23437.939.632.14 7.93 43

36 37.7 38.2 39.6m x 637.731.5338 35.9 35.5 30.5t 830.535.33

m9.246.230.231.03 1.33 3.43 04 x 407.625.036.031.82 0.13 5.23 24 t 42

448.526.824.924.62 1.92 1.82 4446 24.0 27.3 24.8 49.9m x 642.428.622.8248 20.2 25.8 23.3 19.8t 847.222.526.52

054.128.322.227.910.22 3.42 5.61 0552 51.0m x 22.8 20.7 18.6 19.1 22.5 20.1 54.1m x 5254 14.5t 18.5 19.6 17.6 16.1 21.3 19.0 16.9t 54

m5.4565 x 18.6 16.6 13.1 20.1 18.0 16.0 564.7185 t 17.7 15.7 56.8m x 18.4 17.0 15.1 58

m7.8506 x 14.9 11.8t 14.9 16.1 14.3 603.7126 t 14.2 60.3m x 15.3 13.5 62

m6.2646 x 14.4t 14.6 12.8 640.4166 t 64.5m x 12.1 66

68 14.4t 11.5 6870 68.4m x 7072 11.4t 72

80 06070888060788

Unit tonBoom Length (m) neL mooB42 gth (m)

Jib Length (m) neL biJ06 gth (m)Boom Angle (deg.) Boom Angle (deg.)Radius (m) Radius (m)

20 22.4m x 2022 40.8t 22

426.83 42622.63 62829.33 82

30 31.9 33.0m x 3032 30.1 32.4t 32

435.13 5.82 43637.92 0.72 63832.82 6.52 83047.62 3.42 04244.52 2.32 24

44 22.1 24.1 46.3m x 4446 21.1 23.0 23.4t 46

841.22 0.22 2.02 84058.02 0.12 4.91 05256.91 1.02 6.81 25455.81 3.91 9.71 45

56 17.3 18.6 17.4 58.2m x 5658 15.2 17.9 16.5 14.4t 5860 12.8 17.3 15.6 13.6 6062 10.3 16.7 14.7 12.9 6264 62.6m x 14.9 14.0 12.2 6466 9.5t 12.0 13.2 11.5 66

m1.6686 x 12.6 10.9 688.1107 t 11.9 10.3 70

m3.0727 x 9.7 729.1147 t 9.2 74

m2.4767 x 7687t2.987

88 80 70 60

* For notes about the table above, refer to page 46.

Page 48: HYDRAULIC CRAWLER CRANE · SCX3500-3 SPECIFICATIONS Specifications Model CUMMINS QSL9 Type 4-cycle, water-cooled,Direct-injection,Turbo-charger Diesel engine Displacement 8.9 Liters

48

Tower SpecificationsGross Rated Load Table

SPECIFICATIONSSCX3500-3

■Tower 30 m (Rear end Radius: Standard)

Unit tonBoom Length (m) neL mooB03 gth (m)

Jib Length (m) neL biJ0342 gth (m)Boom Angle (deg.) Boom Angle (deg.)Radius (m) Radius (m)

10 12.4m x 1012 100.0t 14.1m x 12

3.987.49 41 t 1416 86.9 19.4m x 619.2818 80.4 85.2t 76.7 21.8m x 18

1.474.172.28 0.57 02 t 20223.379.665.37 5.07 22421.660.362.66 1.26 42

26 48.5 59.7 28.2m x 627.957.9528 35.2 54.2 48.7t 56.8 54.2 31.6m x 2830 28.1m x 8.146.946.749.44 5.94 t 3032 34.4t 231.146.543.832.14 0.34

m4.2343 x 38.1 36.2m x 33.8m x 430.832.248.9363 t 35.3 31.5t 29.7t 633.532.93

m6.7383 x m4.048.231.535.92 x 383.3304 t 27.5 38.2m x 30.7 27.0t 40

9.337.5224 t 28.7 25.6 42 m4.2444 x 43.4m x 24.0 44

4.5264 t 27.5t 22.6 4648 21.3 4850 48.2m x 5052 21.2t 52

80 06078806070888

Unit tonBoom Length (m) neL mooB03 gth (m)

Jib Length (m) neL biJ2463 gth (m)Boom Angle (deg.) Boom Angle (deg.)Radius (m) Radius (m)

12 15.8m x 1214 78.7t 17.5m x 14

6.961.87 61 t 16814.866.27 81029.366.76 02

22 63.2 24.3m x 229.9524 59.4 64.4t 56.2 26.7m x 24

5.650.351.95 1.65 62 t 26821.352.056.35 2.35 82034.847.740.94 7.05 03

32 47.9 45.1 34.9m x 235.444.5434 44.5 41.6 36.0t 431.145.34

m3.831.839.046.43 6.83 3.73 63 x 361.134.532.832.23 0.63 5.03 83 t 38

40 39.6m x 043.921.334.530.03 6.33 42 24.8t 31.5 28.1 44.6m x 244.729.039.92

8.223.62 6.82 44 t 447.520.927.42 m4.549.128.42 64 x 27.3 24.1 48.7m x 46

8.026.024.32 84 t 25.8 22.7 19.4t 48 m2.9405 x 19.4 49.8m x 21.4 18.7 50

6.2225 t 3.423.81 t 20.3 17.6 52456.61 2.914.7145

56 55.0m x 15.7 5658 18.7t 14.9 5860 59.8m x 6062 14.2t 62

88 80 70 6088 80 70 60

* For notes about the table above, refer to page 46.

Page 49: HYDRAULIC CRAWLER CRANE · SCX3500-3 SPECIFICATIONS Specifications Model CUMMINS QSL9 Type 4-cycle, water-cooled,Direct-injection,Turbo-charger Diesel engine Displacement 8.9 Liters

49

Tower SpecificationsGross Rated Load Table

SPECIFICATIONS SCX3500-3

■Tower 30 m (Rear end Radius: Standard)

Unit tonBoom Length (m) neL mooB03 gth (m)

Jib Length (m) neL biJ4584 gth (m)Boom Angle (deg.) Boom Angle (deg.)Radius (m) Radius (m)

16 19.2m x 1618 62.1t 20.9m x 18

2.555.06 02 t 20221.358.65 22426.944.35 42

26 50.3 29.1m x 625.6428 47.6 49.8t 43.8 31.6m x 28

8.343.148.74 1.54 03 t 30234.341.939.34 9.24 23439.930.735.04 9.04 43639.632.535.73 2.93 63

38 37.5 34.8 41.6m x 833.436.3340 35.1 32.5 27.1t 049.130.23

m0.548.927.038.62 4.03 0.33 24 x 427.329.724.920.52 5.82 0.13 44 t 44

649.222.622.825.32 8.62 7.82 64845.127.428.621.22 2.52 4.42 84

50 19.9 23.8 20.8 52.9m x 052.023.322.5252 51.2m x 22.5 19.6 16.5t 250.919.123.3254 17.1t 21.3 18.5 16.0 19.7 20.8 17.9 57.1m x 54

m6.5565 x 17.6 15.1 16.0 19.7 16.9 13.9t 564.0285 t 16.6 14.2 57.0m x 18.6 16.0 13.6 58

1.415.318.51 06 t 17.7 15.2 12.8 60 m8.0626 x 12.8 61.4m x 14.4 12.1 62

5.5146 t 1.711.21 t 13.6 11.4 64 m6.5666 x 13.0 10.8 66

6.1186 t 66.6m x 10.2 6870 12.8t 9.7 7072 71.4m x 7274 9.3t 74

88 80 70 60 88 80 70 60

Unit tonBoom Length (m) neL mooB03 gth (m)

Jib Length (m) neL biJ06 gth (m)Boom Angle (deg.) Boom Angle (deg.)Radius (m) Radius (m)

20 22.6m x 2022 40.7t 22

428.83 42623.63 62821.43 82031.23 03232.03 23434.23 6.82 43635.03 0.72 63839.82 7.52 83044.72 4.42 04240.62 2.32 24447.42 1.22 44

46 21.2 23.5 48.3m x 4648 20.2 22.4 20.7t 48

056.91 4.12 4.91 05255.81 5.02 6.81 25454.71 7.91 9.71 45654.61 9.81 3.71 65

58 16.7 18.1 15.5 61.2m x 5860 15.9 17.2 14.6 11.7t 6062 12.9 16.3 13.8 11.5 6264 62.8m x 15.5 13.1 10.8 6466 11.6t 14.7 12.4 10.2 66

m2.7686 x 11.7 9.6 683.4107 t 11.1 9.0 70

275.8 5.01 27 m4.2747 x 8.0 74

4.0167 t 7.6 76 m2.7787 x 78

08t3.708

88 80 70 60

* For notes about the table above, refer to page 46.

Page 50: HYDRAULIC CRAWLER CRANE · SCX3500-3 SPECIFICATIONS Specifications Model CUMMINS QSL9 Type 4-cycle, water-cooled,Direct-injection,Turbo-charger Diesel engine Displacement 8.9 Liters

50

Tower SpecificationsGross Rated Load Table

SPECIFICATIONSSCX3500-3

■Tower 36 m (Rear end Radius: Standard)

Unit tonBoom Length (m) neL mooB63 gth (m)

Jib Length (m) neL biJ0342 gth (m)Boom Angle (deg.) Boom Angle (deg.)Radius (m) Radius (m)

10 12.7m x 1012 98.3t 14.4m x 12

8.682.39 41 t 14618.181.68 61

18 79.9 20.4m x 812.6720 74.5 78.2t 71.2 22.9m x 20

0.869.665.17 9.96 22 t 22423.463.364.46 7.46 42624.857.955.85 8.05 62

28 37.4 53.2 30.3m x 822.354.6530 28.3m x 48.6 42.4t 49.5 48.7 33.6m x 3032 35.2t 8.637.440.044.93 7.44 t 32

m4.3343 x 432.634.144.033.63 9.0463 t 33.7 39.2m x 34.1m x 636.334.83

0.623.13 83 t 29.8t 832.138.53 m6.9304 x 25.3 39.2m x 29.1 43.4m x 40

6.9224 t 3.437.32 t 27.3 22.4t 42440.22 6.521.2244

m4.5464 x 45.4m x 20.6 462.1284 t 24.6t 19.4 48

50 18.3 5052 51.2m x 5254 17.7t 54

80 06078806070888

Unit tonBoom Length (m) neL mooB63 gth (m)

Jib Length (m) neL biJ2463 gth (m)Boom Angle (deg.) Boom Angle (deg.)Radius (m) Radius (m)

14 16.1m x 17.8m x 1416 76.5t 67.8t 16

814.767.17 81023.362.76 02

22 63.1 25.3m x 225.9524 59.5 59.6t 56.1 27.7m x 24

7.251.357.75 4.65 62 t 26820.254.056.25 6.35 82035.740.841.84 2.15 03236.349.542.44 4.74 23

34 44.0 40.8 37.0m x 432.045.3436 38.8 37.8 31.7t 633.734.04

m3.046.438.735.03 2.53 9.13 83 x 3840 39.9m x 5.723.234.535.82 9.23 t 4042 25.0t 249.522.032.136.62 8.03

m6.749.42 9.82 44 x 443.424.828.52 m0.5464 x 23.4 18.9t 45.6m x 648.227.62

1.8284 t 22.1 18.7 21.3t 25.2 21.4 51.7m x 480.612.028.326.718.02 05 t 50

m2.1525 x 16.6 50.8m x 19.1 15.8 522.0245 t 2.326.51 t 18.0 14.9 54

651.41 1.718.4165 m0.7585 x 57.0m x 13.3 58

4.4106 t 16.6t 12.6 6062 11.9 6264 62.8m x 6466 11.7t 66

88 80 70 6088 80 70 60

* For notes about the table above, refer to page 46.

Page 51: HYDRAULIC CRAWLER CRANE · SCX3500-3 SPECIFICATIONS Specifications Model CUMMINS QSL9 Type 4-cycle, water-cooled,Direct-injection,Turbo-charger Diesel engine Displacement 8.9 Liters

51

Tower SpecificationsGross Rated Load Table

SPECIFICATIONS SCX3500-3

■Tower 36 m (Rear end Radius: Standard)

Unit tonBoom Length (m) neL mooB63 gth (m)

Jib Length (m) neL biJ4584 gth (m)Boom Angle (deg.) Boom Angle (deg.)Radius (m) Radius (m)

16 19.5m x 1618 60.6t 21.2m x 18

7.257.95 02 t 20223.252.65 22429.941.35 42627.642.05 62

28 47.6 30.2m x 829.3430 45.3 46.4t 41.4 32.6m x 30

4.142.930.34 2.34 23 t 32431.931.736.93 3.14 43631.633.536.63 6.93 63835.336.330.43 1.73 83

40 34.7 31.7 43.7m x 042.131.2342 32.6 29.6 23.8t 241.927.03

m0.743.724.926.32 8.72 6.03 44 x 448.026.523.821.22 1.62 8.82 64 t 46

842.020.427.628.02 6.42 4.52 84059.816.222.525.91 2.32 2.12 05

52 51.4m x 21.9 18.4 55.9m x 258.714.127.3254 18.0t 20.7 17.4 13.4t 458.612.029.02

658.511.914.714.314.61 7.91 65 m6.6585 x 15.5 12.6 57.2m x 18.1 14.9 60.1m x 58

4.9106 t 14.7 11.9 15.2t 17.2 14.1 11.2t 60265.01 3.313.612.110.41 26

m8.2646 x 10.6 62.4m x 12.6 9.9 647.3166 t 2.610.01 t 12.0 9.3 66

868.8 4.115.9 86 m6.8607 x 68.6m x 8.3 70

2.11t4.927 t 7.8 7274 7.4 7476 74.4m x 7678 7.3t 78

88 80 70 60 88 80 70 60

Unit tonBoom Length (m) neL mooB63 gth (m)

Jib Length (m) neL biJ06 gth (m)Boom Angle (deg.) Boom Angle (deg.)Radius (m) Radius (m)

20 22.9m x 2022 40.5t 22

420.93 42625.63 62823.43 82032.23 03

32 30.3 35.1m x 3234 28.7 32.2t 34

634.13 1.72 63837.92 7.52 83041.82 4.42 04246.62 3.32 24443.52 2.22 44641.42 2.12 64

48 20.3 22.9 50.4m x 4850 19.4 21.9 18.1t 50

252.71 9.02 6.81 25452.61 7.91 9.71 45652.51 6.81 3.71 65853.41 6.71 7.61 85065.31 7.61 2.61 06

62 14.3 15.8 12.8 64.2m x 6264 63.0m x 15.0 12.0 9.2t 6466 12.7t 14.2 11.4 8.7 66

862.8 8.01 5.31 86 m2.8607 x 10.2 7.7 70

5.3127 t 9.6 7.2 72477.6 1.9 47

m4.4767 x 6.3 76878.5 t0.987085.5 08

m2.0828 x 8248t4.548

88 80 70 60

* For notes about the table above, refer to page 46.

Page 52: HYDRAULIC CRAWLER CRANE · SCX3500-3 SPECIFICATIONS Specifications Model CUMMINS QSL9 Type 4-cycle, water-cooled,Direct-injection,Turbo-charger Diesel engine Displacement 8.9 Liters

52

Tower SpecificationsGross Rated Load Table

SPECIFICATIONSSCX3500-3

■Tower 42 m (Rear end Radius: Standard)

Unit tonBoom Length (m) neL mooB24 gth (m)

Jib Length (m) neL biJ0342 gth (m)Boom Angle (deg.) Boom Angle (deg.)Radius (m) Radius (m)

10 12.9m x 1012 92.3t 14.6m x 12

8.186.88 41 t 14610.873.28 61

18 76.9 21.5m x 810.3720 72.3 71.4t 68.5 23.9m x 20

0.367.465.96 4.86 22 t 22427.263.166.26 3.56 42620.755.859.65 7.25 62821.250.650.25 3.93 82

30 28.5m x 47.6 32.3m x 038.741.1532 35.6t 43.8 37.0t 41.5 44.0 35.7m x 32

4.236.049.135.43 4.04 43 t 34 m5.4363 x 32.0 34.3m x 630.237.73

6.9383 t 3.037.92 t 838.921.53 m2.247.72 04 x 048.728.23

m7.1424 x 21.4t 40.3m x 240.621.6244 t 5.231.02 t 24.4 46.4m x 44

6.819.228.8164 t 46 m5.747.7184 x 17.7 48

m4.8405 x 21.9t 16.6 504.7125 t 15.7 52

54 14.8 5456 54.2m x 5658 14.7t 58

80 06078806070888

Unit tonBoom Length (m) neL mooB24 gth (m)

Jib Length (m) neL biJ2463 gth (m)Boom Angle (deg.) Boom Angle (deg.)Radius (m) Radius (m)

14 16.3m x 1416 72.3t 16

811.465.86 81025.064.46 02221.757.06 22

24 57.4 26.3m x 420.4526 54.6 55.2t 51.2 28.8m x 26

7.848.841.15 1.25 82 t 28032.646.649.64 9.94 03236.246.442.34 9.64 23433.939.249.93 5.34 43

36 40.0 37.0 39.0m x 634.630.0438 33.0 34.4 27.8t 838.333.73

m4.245.130.539.62 1.23 7.52 04 x 4042 40.1m x 1.425.921.231.52 1.03 t 4244 25.3t 448.227.727.625.32 2.82

m9.541.22 6.62 64 x 644.120.62 m1.6484 x 20.7 50.6m x 21.3t 841.025.42

5.6205 t 19.6 15.4t 059.811.32 m9.158.415.81 25 x 17.8 54.7m x 52

m3.3545 x 9.129.31 t 16.8 12.9t 548.7165 t 654.21 9.511.31

857.11 0.514.2185 m1.957.1106 x 11.0 60

62 14.6t 10.4 6264 9.8 6466 65.8m x 6668 9.3t 68

80 70 6088 80 70 60 88

* For notes about the table above, refer to page 46.

Page 53: HYDRAULIC CRAWLER CRANE · SCX3500-3 SPECIFICATIONS Specifications Model CUMMINS QSL9 Type 4-cycle, water-cooled,Direct-injection,Turbo-charger Diesel engine Displacement 8.9 Liters

53

Tower SpecificationsGross Rated Load Table

SPECIFICATIONS SCX3500-3

■Tower 42 m (Rear end Radius: Standard)

Unit tonBoom Length (m) neL mooB24 gth (m)

Jib Length (m) neL biJ4584 gth (m)Boom Angle (deg.) Boom Angle (deg.)Radius (m) Radius (m)

16 19.7m x 1618 54.9t 21.4m x 18

8.648.45 02 t 20225.646.35 22426.549.05 42627.443.84 62

28 45.9 31.2m x 820.3430 43.8 43.6t 41.0 33.7m x 30

5.832.932.24 9.14 23 t 32431.833.739.83 2.04 43632.534.530.63 6.83 63837.237.335.33 0.73 83044.032.232.13 6.43 04

42 32.5 29.1 45.7m x 244.827.0344 30.5 27.3 21.1t 445.625.92

m1.949.429.729.02 6.52 7.82 64 x 461.814.323.626.91 1.42 3.62 84 t 48

056.710.229.424.81 7.22 0.22 0552 51.7m x 255.617.025.324.71 5.12 54 18.2t 455.516.915.124.61 3.02

m9.854.51 3.91 65 x 656.415.810.81 m7.7585 x 14.6 10.8t 57.4m x 858.315.71

4.8106 t 13.8 10.5 15.4t 16.6 13.0 63.1m x 6026t5.83.218.518.9 1.31 26

m5.362.9 4.21 46 x 11.6 8.2 64 m9.4666 x 2.517.8 t 10.9 7.7 66

1.2186 t 861.7 4.012.8 077.6 8.9 7.7 07

m6.1727 x 70.7m x 6.2 72478.5 t6.9t3.747

76 5.4 7678 77.4m x 7880 5.2t 80

88 80 70 60 88 80 70 60

Unit tonBoom Length (m) neL mooB24 gth (m)

Jib Length (m) neL biJ06 gth (m)Boom Angle (deg.) Boom Angle (deg.)Radius (m) Radius (m)

20 23.1m x 2022 39.7t 22

422.93 42627.63 62824.43 82033.23 03235.03 23

34 28.8 36.1m x 3436 27.2 32.2t 36

835.03 8.52 83048.82 5.42 04243.72 3.32 24449.52 2.22 44644.42 2.12 64849.22 3.02 84

50 19.4 21.5 52.4m x 5052 18.7 20.3 15.7t 5254 17.9 19.1 15.0 5456 17.3 18.0 14.0 5658 16.7 17.0 13.2 5860 16.1 16.1 12.4 6062 14.8 15.3 11.6 6264 63.2m x 14.5 10.9 6466 13.0t 13.7 10.3 66

867.9 0.31 86 m2.9607 x 9.1 70

6.2127 t 8.6 72471.8 47676.7 67

m5.6787 x 7808t5.708

88 80 70

* For notes about the table above, refer to page 46.

Page 54: HYDRAULIC CRAWLER CRANE · SCX3500-3 SPECIFICATIONS Specifications Model CUMMINS QSL9 Type 4-cycle, water-cooled,Direct-injection,Turbo-charger Diesel engine Displacement 8.9 Liters

54

Tower SpecificationsGross Rated Load Table

SPECIFICATIONSSCX3500-3

■Tower 48 m (Rear end Radius: Standard)

Unit tonBoom Length (m) neL mooB84 gth (m)

Jib Length (m) neL biJ0342 gth (m)Boom Angle (deg.) Boom Angle (deg.)Radius (m) Radius (m)

10 13.2m x 1012 83.7t 14.9m x 12

6.475.18 41 t 14610.271.67 61817.763.17 81

20 67.2 22.5m x 027.3622 63.8 65.8t 60.2 24.9m x 22

1.852.759.06 9.06 42 t 24621.557.453.55 4.45 62824.055.255.05 1.14 82

30 28.7m x 033.646.054.64 32 36.0t 42.8 34.4m x 238.247.24

1.236.93 43 t 33.2 39.7 37.7m x 34 m5.5363 x 30.3 34.5m x 36.8 28.2t 36

4.7383 t 6.031.82 t 839.723.43040.620.231.62 04

m2.544.42 24 x 41.3m x 243.42 m8.3444 x 17.3t 30.7t 448.22

0.3264 t m4.944.128.61 x 468.411.027.5184 t 48

m5.947.4105 x 14.5 50 m4.1525 x 19.2t 13.7 52

1.4145 t 12.9 5456 12.1 5658 57.2m x 5860 11.7t 60

70 6088 80 70 60 88 80

Unit tonBoom Length (m) neL mooB84 gth (m)

Jib Length (m) neL biJ2463 gth (m)Boom Angle (deg.) Boom Angle (deg.)Radius (m) Radius (m)

14 16.6m x 1416 64.5t 18.3m x 16

2.553.36 81 t 18021.457.95 02228.254.65 22

24 53.5 27.4m x 421.0526 51.0 51.0t 47.6 29.8m x 26

3.544.547.94 7.84 82 t 28039.445.346.54 7.64 03234.147.141.24 0.54 23434.832.040.93 4.34 43636.538.832.63 4.04 63

38 34.0 33.7 41.1m x 832.332.7340 26.8 31.5 24.4t 049.039.4342 40.3m x m4.449.827.236.32 4.92 x 4244 25.6t 1.121.726.721.22 6.72 t 44

640.025.529.127.02 0.62 64 m1.7484 x 19.5 46.1m x 848.810.42

2.5205 t 18.3 53.6m x 21.6t 057.716.221.213.71 25 t 256.614.12

m9.250.213.61 45 x 15.7 57.7m x 54 m3.5565 x 9.023.11 t 14.8 9.9t 56

7.5185 t 858.9 0.416.01061.9 2.310.0106

m1.164.9 26 x 8.6 62 m0.3646 x 12.8t 8.0 64

665.7 t1.96668 7.0 6870 68.8m x 7072 6.9t 72

70 6088 80 70 60 88 80

* For notes about the table above, refer to page 46.

Page 55: HYDRAULIC CRAWLER CRANE · SCX3500-3 SPECIFICATIONS Specifications Model CUMMINS QSL9 Type 4-cycle, water-cooled,Direct-injection,Turbo-charger Diesel engine Displacement 8.9 Liters

55

Tower SpecificationsGross Rated Load Table

SPECIFICATIONS SCX3500-3

■Tower 48 m (Rear end Radius: Standard)

Unit tonBoom Length (m) neL mooB84 gth (m)

Jib Length (m) neL biJ4584 gth (m)Boom Angle (deg.) Boom Angle (deg.)Radius (m) Radius (m)

18 21.7m x 180.147.74 02 t 20

229.046.64 22421.046.54 42623.936.44 62825.836.24 82

30 40.7 32.3m x 037.7332 39.0 40.2t 36.3 34.7m x 32

0.638.436.73 4.73 43 t 34633.434.339.43 0.63 63839.132.235.23 8.43 83047.921.133.03 6.33 04248.720.033.82 1.23 24

44 30.2 26.5 47.8m x 440.621.9246 28.4 24.9 18.1t 644.429.72

m1.159.223.620.81 4.32 8.62 84 x 486.516.128.429.61 1.22 7.22 05 t 50

52 51.9m x 252.513.025.328.51 8.02 54 18.3t 452.412.912.229.41 7.91

654.311.817.810.41 6.81 65 m9.162.31 7.71 85 x 57.7m x 17.2 12.5 58

m7.8506 x 12.5 7.7t 15.5t 16.3 11.8 604.7126 t 261.114.517.7 8.11

464.016.412.7 1.11 46 m5.467.6 5.01 66 x 9.8 66

m9.6686 x 5.412.6 t 9.2 683.0107 t 077.8 8.5

272.8 4.5 27 m7.270.5 47 x 74

m2.4767 x 8.0t 7687t0.587

88 80 70 60 88 80 70

Unit tonBoom Length (m) neL mooB84 gth (m)

Jib Length (m) neL biJ06 gth (m)Boom Angle (deg.) Boom Angle (deg.)Radius (m) Radius (m)

20 23.4m x 2022 35.6t 22

424.53 42627.43 62821.43 82035.23 03236.03 23

34 28.9 37.1m x 3436 27.3 32.0t 36

839.03 9.52 83048.82 6.42 04248.62 4.32 24441.52 3.22 44645.32 3.12 64841.22 3.02 84057.02 5.91 05

52 18.7 19.5 54.5m x 5254 17.9 18.4 13.0t 5456 17.3 17.3 12.4 5658 16.7 16.3 11.6 5860 16.1 15.4 10.8 6062 15.3 14.6 10.1 6264 63.5m x 13.8 9.5 6466 13.0t 13.1 8.9 66

863.8 4.21 86078.7 7.11 07

m3.0727 x 7.3 727.1147 t 6.8 74

673.6 67879.5 87

m5.8708 x 8028t8.528

80 7088

* For notes about the table above, refer to page 46.

Page 56: HYDRAULIC CRAWLER CRANE · SCX3500-3 SPECIFICATIONS Specifications Model CUMMINS QSL9 Type 4-cycle, water-cooled,Direct-injection,Turbo-charger Diesel engine Displacement 8.9 Liters

56

Tower SpecificationsGross Rated Load Table

SPECIFICATIONSSCX3500-3

■Tower 54 m (Rear end Radius: Standard)

Unit tonBoom Length (m) neL mooB45 gth (m)

Jib Length (m) neL biJ0342 gth (m)Boom Angle (deg.) Boom Angle (deg.)Radius (m) Radius (m)

10 13.4m x 1012 72.4t 15.1m x 12

8.266.17 41 t 14619.164.86 61810.061.46 81

20 60.5 23.5m x 024.7522 57.4 60.7t 223.45

427.152.95 7.45 42625.353.947.35 6.25 62829.843.741.94 7.24 82

30 28.9m x 039.446.541.54 32 36.3t 235.149.346.14

m4.635.83 43 x 435.834.436.728.53 63 t 34.7m x 35.8 39.8m x 36

m6.6383 x 8.031.62 t 33.4 24.2t 380.5304 t 041.423.133.42

245.223.927.22 24 m4.243.12 44 x 441.12

m8.5464 x 48.2m x 28.9t 648.910.0284 t 13.2t 846.81

m4.256.714.2105 x 50 m6.156.1125 x 11.2t 52

8.619.0145 t 10.6 54 m4.4565 x 10.0 56

7.0185 t 9.4 5860 8.8 6062 60.2m x 6264 8.7t 64

70 6088 80 70 60 88 80

Unit tonBoom Length (m) neL mooB45 gth (m)

Jib Length (m) neL biJ2463 gth (m)Boom Angle (deg.) Boom Angle (deg.)Radius (m) Radius (m)

14 16.8m x 1416 54.4t 18.5m x 16

2.745.35 81 t 18023.640.25 02221.546.05 22420.442.84 42

26 45.9 28.4m x 628.2428 43.9 47.4t 40.8 30.9m x 28

7.141.933.44 1.24 03 t 30238.935.738.04 5.04 23438.630.638.73 1.93 43632.438.432.53 9.73 63839.136.338.23 9.43 83

40 27.8 30.7 43.1m x 048.927.2342 40.5m x 28.8 20.9t 249.729.1344 25.8t m5.641.622.823.02 0.72 x 44

7.716.427.220.91 4.52 64 t 46 m3.649.71 9.32 84 x 848.611.32

m1.8405 x 7.128.61 t 058.518.129.3225 t 258.416.028.51

m6.659.41 45 x 53.9m x 459.316.91t9.81.41 65 t 651.31

m4.7585 x m7.063.215.8 x 585.3106 t 06t7.66.110.8

264.6 0.114.7 26 m2.360.7 46 x 5.9 64

6.015.6 66 t 5.4 6668 5.0 6870 68.2m x 7072 5.0t 72

6088 80 70 60 88 80 70

* For notes about the table above, refer to page 46.

Page 57: HYDRAULIC CRAWLER CRANE · SCX3500-3 SPECIFICATIONS Specifications Model CUMMINS QSL9 Type 4-cycle, water-cooled,Direct-injection,Turbo-charger Diesel engine Displacement 8.9 Liters

57

Tower SpecificationsGross Rated Load Table

SPECIFICATIONS SCX3500-3

■Tower 54 m (Rear end Radius: Standard)

Unit tonBoom Length (m) neL mooB45 gth (m)

Jib Length (m) neL biJ4584 gth (m)Boom Angle (deg.) Boom Angle (deg.)Radius (m) Radius (m)

18 20.3m x 1820 40.9t 20

229.532.04 22421.533.93 42624.434.83 62827.335.73 82

30 36.4 33.3m x 030.3332 34.9 37.0t 32.3 35.7m x 32

4.230.134.63 5.33 43 t 34632.238.928.33 2.23 63835.036.825.13 1.13 83044.826.724.92 1.03 04245.627.625.72 2.92 24448.428.528.52 4.82 44

46 27.7 24.2 49.8m x 643.321.5248 26.8 22.8 15.4t 849.124.4250 23.3 21.5 15.3 23.8 20.6 53.2m x 5052 18.8 20.3 14.3 23.2 19.4 12.8t 5254 52.1m x 19.1 13.4 22.0 18.3 12.4 5456 18.5t 18.1 12.6 19.2 17.2 11.6 56

m9.759.11 2.71 85 x 16.3 10.9 58 m7.9506 x 11.2 15.6t 15.4 10.2 60

4.6126 t 265.9 6.415.01 469.8 8.319.9 46

m5.563.9 66 x 8.3 663.317.8 86 t 7.8 68

m0.9607 x 7.3 70278.6 t5.827

74 6.4 7476 74.8m x 7678 6.2t 78

88 80 70 88 80 70

Unit tonBoom Length (m) neL mooB45 gth (m)

Jib Length (m) neL biJ06 gth (m)Boom Angle (deg.) Boom Angle (deg.)Radius (m) Radius (m)

20 23.7m x 2022 31.0t 22

420.13 42626.03 62820.03 82034.92 03239.82 23433.82 43

36 26.9 38.2m x 3638 25.5 28.1t 38

041.72 3.42 04240.62 1.32 24443.42 0.22 44648.22 1.12 64844.12 2.02 84050.02 3.91 05259.81 5.81 25

54 17.8 17.7 56.5m x 5456 17.2 16.7 10.8t 5658 16.6 15.8 10.2 5860 16.0 14.9 9.5 6062 15.5 14.0 8.9 6264 63.4m x 13.3 8.3 6466 13.3t 12.5 7.7 66

862.7 9.11 86077.6 2.11 07

m1.1727 x 6.2 729.0147 t 5.7 74

673.5 67 m5.7787 x 78

08t0.508

708088

* For notes about the table above, refer to page 46.

Page 58: HYDRAULIC CRAWLER CRANE · SCX3500-3 SPECIFICATIONS Specifications Model CUMMINS QSL9 Type 4-cycle, water-cooled,Direct-injection,Turbo-charger Diesel engine Displacement 8.9 Liters

58

Tower SpecificationsGross Rated Load Table

SPECIFICATIONSSCX3500-3

■Tower 60 m (Rear end Radius: Standard)

Unit tonBoom Length (m) neL mooB06 gth (m)

Jib Length (m) neL biJ6303 gth (m)Boom Angle (deg.) Boom Angle (deg.)Radius (m) Radius (m)

12 15.4m x 1214 52.6t 17.1m x 14

8.541.25 61 t 16812.544.05 81029.348.84 02226.243.74 22

24 45.2 27.0m x 424.1426 43.1 46.6t 40.1 29.5m x 26

4.043.835.54 2.14 82 t 28030.046.633.34 6.93 03232.831.532.04 2.83 23433.638.333.73 5.53 43

36 34.9m x 637.337.237.43 38 31.0t 32.3 41.8m x 834.137.13

6.023.03 04 t 044.926.82 m7.045.02 4.82 24 x 27.5 45.2m x 42

m4.3444 x 0.622.91 t 25.8 17.4t 442.7264 t 649.613.420.81

848.519.229.61 84 m2.949.51 05 x 058.41

m4.559.41 25 x 22.1t 259.31 m7.3545 x 451.31t9.7

2.4165 t m6.953.218.7 x 5685t7.56.112.7 85

m4.957.6 06 x 5.6 601.112.6 26 t 5.2 62

m2.3646 x 62.8m x 6466t0.5t0.666

70 6088 80 70 60 88 80

Unit tonBoom Length (m) neL mooB06 gth (m)

Jib Length (m) neL biJ8424 gth (m)Boom Angle (deg.) Boom Angle (deg.)Radius (m) Radius (m)

16 18.8m x 1618 40.2t 20.5m x 18

3.536.93 02 t 20227.436.83 22429.335.73 42620.336.63 62

28 35.5 31.9m x 823.2330 33.9 35.2t 035.13

m3.432.032.53 5.23 23 x 327.039.826.33 2.13 43 t 34

636.928.722.23 0.03 63834.827.628.03 0.92 83041.728.528.82 0.82 04249.529.429.62 2.72 24445.421.423.52 6.62 44

46 23.4 23.7 48.5m x 640.325.3248 46.5m x 22.4 14.8t 22.9 21.7 51.9m x 4850 21.9t 21.1 14.1 22.3 20.4 12.4t 50

254.212.913.912.31 9.91 25 m3.254.21 8.81 45 x 18.2 11.6 54

m0.5565 x 11.6 18.6t 17.2 10.8 563.8185 t 851.012.619.01

065.9 4.512.01 06 m8.066.9 26 x 8.9 62

1.510.9 46 t 8.3 64 m2.5666 x 7.8 66

863.7 t7.88670 6.8 7072 71.0m x 7274 6.6t 74

80 7088 80 70 88

* For notes about the table above, refer to page 46.

Page 59: HYDRAULIC CRAWLER CRANE · SCX3500-3 SPECIFICATIONS Specifications Model CUMMINS QSL9 Type 4-cycle, water-cooled,Direct-injection,Turbo-charger Diesel engine Displacement 8.9 Liters

59

Tower SpecificationsGross Rated Load Table

SPECIFICATIONS SCX3500-3

■Tower 60 m (Rear end Radius: Standard)

Unit tonBoom Length (m) neL mooB06 gth (m)

Jib Length (m) neL biJ0645 gth (m)Boom Angle (deg.) Boom Angle (deg.)Radius (m) Radius (m)

20 22.3m x 2022 30.9t 22

422.724.03 42627.627.92 62821.621.92 82036.524.82 03230.527.72 23

34 26.5 36.8m x 434.4236 25.4 26.6t 23.3 39.2m x 36

8.223.229.52 4.42 83 t 38044.225.129.42 5.32 04245.126.029.32 7.22 24447.029.918.22 9.12 44648.912.918.12 2.12 64849.815.819.02 6.02 84051.810.819.91 0.02 05

52 19.5 18.7 55.2m x 17.4 17.4 5254 19.1 17.6 10.5t 17.0 16.7 5456 18.6 16.6 10.2 16.5 15.8 5658 57.9m x 15.7 9.5 16.2 14.8 5860 15.7t 14.8 8.8 15.8 14.0 60

262.314.512.8 0.41 26 m7.366.7 3.31 46 x 12.4 64

2.311.7 5.21 66 t 11.7 66 m4.6686 x 861.116.6

4.2107 t 074.011.6 279.9 7.5 27

m2.273.5 47 x 74 m5.5767 x 9.8t 76

87t0.587

70 88 8088 80

* For notes about the table above, refer to page 46.

Page 60: HYDRAULIC CRAWLER CRANE · SCX3500-3 SPECIFICATIONS Specifications Model CUMMINS QSL9 Type 4-cycle, water-cooled,Direct-injection,Turbo-charger Diesel engine Displacement 8.9 Liters

60

Tower SpecificationsGross Rated Load Table

SPECIFICATIONSSCX3500-3

■Tower 24 m (Rear end Radius: Short)

Unit tonBoom Length (m) neL mooB42 gth (m)

Jib Length (m) neL biJ2463 gth (m)Boom Angle (deg.) Boom Angle (deg.)Radius (m) Radius (m)

12 15.5m x 1241x m2.71t1.974161t9.965.77 61819.769.17 81023.36x m2.326.66 0222x m7.522.95t4.467.16 2242t0.655.551.26 4.75 42625.559.154.65 7.35 62828.057.845.15 5.05 82037.648.54x m9.234.74 7.74 03231.343.34t5.838.34 9.44 2343x m2.639.931.149.63 6.04 2.04 4363t3.331.732.834.43 8.73 2.33 63833.136.437.53x m6.141.23 3.53 7.62 83042.924.238.03t6.520.03 1.33 x m4.9304

42 21.9t 29.1 28.1 25.3 25.7 30.4 27.4 45.7m x 4244t7.12 6.829.027.325.62 x m9.2444645.12 2.429.62x m2.543.220.52 t7.5264842.02 8.221.32t8.710.12x m1.7484051.91 5.12x m7.849.91t2.4205250.81 4.02t1.12x m0.1525450.71 x m9.25t3.9145

56 19.9t 16.1 5658 56.8m x 5860 15.8t 60

88 80 70 60 88 80 70 60

Unit tonBoom Length (m) neL mooB42 gth (m)

Jib Length (m) neL biJ0342 gth (m)Boom Angle (deg.) Boom Angle (deg.)Radius (m) Radius (m)

- -x m8.311.21t0.090.0011.21

412.989.29 41611.28x m3.810.48 6181x m8.029.47t6.588.67 8102t3.479.861.87 8.07 02227.969.368.96 8.56 22428.266.95x m1.629.26 6.85 4262x m5.921.759.55t4.251.75 5.54 6282t0.543.258.251.84 3.25 x m8.7282031.441.841.44x m2.332.44 1.84 t7.3303237.045.448.43t5.538.04 x m3.132343x m4.738.733.14x m6.335.438.73 t8.834363t4.032.535.73t3.720.23x m5.5363837.92 9.23x m1.739.92t8.5383048.72 8.03t6.13x m4.9304241.62 x m3.14t5.8224

44 29.6t 24.6 4446 45.2m x 4648 23.7t 48

70 608088 80 70 60 88

7.52

such as hook, from figures shown above.

Hook HookMass (ton) 7falls 6falls 5falls 4falls 3falls 2falls 1fall

100t 3.11 100 90 76 61 46 31 -45t 2.17 - - - - 45 31 -15t 0.62 - - - - - - 15

Maximum Rated Load (ton)

5. The 145 ton counter weight and 25 ton lower weight are required for all capacities on these charts.

7. The usable hook when lifting tower jib is described on page 41. Using the unusable hook cause the jib to swing. 8. Correlation between the number of reeved lines, maximum rated loads, hook mass are shown in the table below.

6. Figures described as OOm x OOt in the tables indicate "working radius" m x "rated load" ton.

4. Working radius is the horizontal distance from the swing center to the center of gravity of a lifted load. 3. The figures surrounded by bold lines are based on factors other than those which would cause a tioping condition.

2. To calculate the maximum load that can actually be lifted, deduct mass of all lifting accessories, level ground.

9. The necessary mass to lower the hook refers "Lowerable Jib Hook Mass" on page 42.

1. The rated loads are determined according to EN13000 rating on the condition that the machine is stationed on firm,

Capacity

12. The gross rated load value of the jib with the sheave block the boom top is after 1.1 ton is deducted from the gross rated load of the jib.11. Remove the sheave block the boom top when using jib length 54 or 60 m for boom length 54 m.10. Be sure to attach the balance weight (420kg x 2) to the top jib when the jib length is 24m.

Page 61: HYDRAULIC CRAWLER CRANE · SCX3500-3 SPECIFICATIONS Specifications Model CUMMINS QSL9 Type 4-cycle, water-cooled,Direct-injection,Turbo-charger Diesel engine Displacement 8.9 Liters

61

Tower SpecificationsGross Rated Load Table

SPECIFICATIONS SCX3500-3

■Tower 24 m (Rear end Radius: Short)

Unit tonBoom Length (m) neL mooB42 gth (m)

Jib Length (m) neL biJ4584 gth (m)Boom Angle (deg.) Boom Angle (deg.)Radius (m) Radius (m)

16 18.9m x 1681x m6.02t4.268102t4.551.06 02228.253.65 22424.948.25 42623.64x m1.827.94 6282x m5.036.34t3.949.64 8203t5.341.149.54 4.44 03237.149.833.24 9.14 23436.839.632.93 7.93 43638.531.53x m6.934.63 6.73 63833.335.33t9.829.33 0.53 8304x m9.241.130.235.82 7.13 7.23 0424t1.521.921.036.62 7.92 7.03 24443.423.723.820.52 9.72 1.82 44647.226.526.62x m9.944.32 2.62 0.42 64844.121.420.52t3.811.22 8.42 2.02 84051.027.222.223.818.02 4.32 5.61 05

52 51.0m x 22.1 19.6 17.2 19.1 21.5 18.9 54.1m x 5254 14.5t 18.5 18.6 16.2 16.1 20.3 17.9 15.4t 54

656.41 9.612.911.313.516.71 x m5.4565857.31 0.612.81x m8.655.417.61 t4.7185069.21 1.519.41t8.117.31x m7.8506262.21 3.41x m3.060.31t4.6126465.11 6.31t4.41x m6.2646669.01 x m5.46t8.2166

68 13.4t 10.3 6870 68.4m x 7072 10.2t 72

70 60 88 80 70 608088

Unit tonBoom Length (m) neL mooB42 gth (m)

Jib Length (m) neL biJ06 gth (m)Boom Angle (deg.) Boom Angle (deg.)Radius (m) Radius (m)

02x m4.220222t8.0422426.83 42622.63 62829.33 8203x m0.339.13 0323t4.231.03 23435.13 5.82 43637.92 0.72 63832.82 6.52 83047.62 3.42 04244.52 2.32 2444x m3.641.42 1.22 4464t9.120.32 1.12 64847.02 0.22 2.02 84054.91 0.12 4.91 05253.81 1.02 6.81 25452.71 3.91 9.71 45

56 17.3 18.6 16.2 58.2m x 5658 15.2 17.6 15.3 12.9t 5860 12.8 16.7 14.4 12.2 6062 10.3 15.8 13.6 11.5 6264 62.6m x 14.9 12.9 10.8 6466 9.5t 12.0 12.2 10.2 66

866.9 5.11 x m1.6686070.9 9.01 t8.1107275.8 x m3.0727470.8 t8.014767x m2.476787t0.887

88 80 70 60

* For notes about the table above, refer to page 60.

Page 62: HYDRAULIC CRAWLER CRANE · SCX3500-3 SPECIFICATIONS Specifications Model CUMMINS QSL9 Type 4-cycle, water-cooled,Direct-injection,Turbo-charger Diesel engine Displacement 8.9 Liters

62

Tower SpecificationsGross Rated Load Table

SPECIFICATIONSSCX3500-3

■Tower 30 m (Rear end Radius: Short)

Unit tonBoom Length (m) neL mooB03 gth (m)

Jib Length (m) neL biJ0342 gth (m)Boom Angle (deg.) Boom Angle (deg.)Radius (m) Radius (m)

10 12.4m x 1021x m1.41t0.0012141t2.984.49 41616.28x m4.916.68 6181x m8.125.67t3.771.08 8102t1.761.176.47 7.47 02224.666.666.66 1.96 22429.954.260.06 1.26 42624.457.65x m2.825.45 5.84 6282x m6.137.949.15t1.448.94 2.53 8203t1.837.546.749.04 7.54 x m1.8203235.732.243.837.73 2.24 t4.4323438.432.93x m8.33x m2.639.43 x m4.2343633.235.63t7.92t3.824.23 t8.936383x m4.042.031.436.62x m6.738304t2.422.82x m2.838.42t7.0304240.32 5.62t9.332.3224446.12 x m4.34x m4.2444643.02 t4.52t9.2264

48 19.2 4850 48.2m x 5052 19.1t 52

80 06078806070888

Unit tonBoom Length (m) neL mooB03 gth (m)

Jib Length (m) neL biJ2463 gth (m)Boom Angle (deg.) Boom Angle (deg.)Radius (m) Radius (m)

12 15.8m x 1241x m5.71t4.874161t3.968.77 61811.863.27 81027.363.76 02226.95x m3.429.26 2242x m7.620.65t2.851.95 4262t2.158.256.35 8.55 62823.849.940.94 3.15 82033.445.640.54 1.74 03238.049.24x m9.435.14 5.34 23438.738.93t8.235.83 3.04 4363x m3.831.530.735.13 8.53 3.73 6383t3.827.235.434.92 4.33 5.03 83046.626.033.234.72 3.13 x m6.9304249.427.829.92x m6.447.52 4.92 t8.4224443.329.627.42t3.021.42 6.72 4464x m7.849.124.52x m4.544.917.22 6484t1.716.029.32t8.023.814.12 84054.61 4.91x m8.942.71x m2.9405254.51 4.81t8.223.61t7.0225455.41 4.714.5145

56 55.0m x 13.7 5658 16.9t 12.9 5860 59.8m x 6062 12.3t 62

88 80 70 6088 80 70 60

* For notes about the table above, refer to page 60.

Page 63: HYDRAULIC CRAWLER CRANE · SCX3500-3 SPECIFICATIONS Specifications Model CUMMINS QSL9 Type 4-cycle, water-cooled,Direct-injection,Turbo-charger Diesel engine Displacement 8.9 Liters

63

Tower SpecificationsGross Rated Load Table

SPECIFICATIONS SCX3500-3

■Tower 30 m (Rear end Radius: Short)

Unit tonBoom Length (m) neL mooB03 gth (m)

Jib Length (m) neL biJ4584 gth (m)Boom Angle (deg.) Boom Angle (deg.)Radius (m) Radius (m)

16 19.2m x 1681x m9.02t9.168102t1.553.06 02221.355.65 22426.942.35 42625.64x m1.921.05 6282x m6.138.34t3.543.74 8203t1.043.145.34 9.44 03235.931.931.04 3.24 23434.630.731.73 1.93 43638.332.534.43 3.63 63834.133.33x m6.140.23 8.33 83043.921.13t4.429.92 6.13 0424x m0.543.721.921.42 0.82 6.92 2444t1.126.522.726.22 2.62 8.72 44644.020.426.522.12 7.42 2.62 64841.916.221.429.91 2.32 4.42 84050.813.127.22x m9.257.81 9.12 9.91 05259.611.025.12t2.416.71 7.02 x m2.1525

54 17.1t 19.6 16.6 13.7 19.7 18.9 15.9 57.1m x 5465t7.110.519.710.619.217.51 x m6.5565854.11 1.410.71x m0.751.218.41 t8.8185066.01 3.311.61t1.414.111.41 06260.01 6.21x m4.168.01x m8.0626464.9 9.11t5.512.01t8.3146668.8 3.11x m6.5666863.8 x m6.66t8.986

70 11.1t 7.8 7072 71.4m x 7274 7.5t 74

88 80 70 60 88 80 70 60

Unit tonBoom Length (m) neL mooB03 gth (m)

Jib Length (m) neL biJ06 gth (m)Boom Angle (deg.) Boom Angle (deg.)Radius (m) Radius (m)

02x m6.220222t7.0422428.83 42623.63 62821.43 82031.23 03232.03 23434.23 6.82 43635.03 0.72 63839.82 7.52 83044.72 4.42 04240.62 2.32 24447.42 1.22 4464x m3.845.32 2.12 6484t3.810.22 2.02 84053.71 7.02 4.91 05252.61 5.91 6.81 25452.51 3.81 9.71 45653.41 3.71 3.71 65

58 16.7 16.3 13.4 61.2m x 5860 15.9 15.5 12.6 9.5t 6062 12.9 14.6 11.9 9.3 6264 62.8m x 13.8 11.2 8.7 6466 11.6t 13.1 10.6 8.1 66

865.7 9.9 x m2.7686070.7 4.9 t7.2107276.6 8.8 27471.6 x m4.2747677.5 t7.86787x m2.778708t5.508

88 80 70 60

* For notes about the table above, refer to page 60.

Page 64: HYDRAULIC CRAWLER CRANE · SCX3500-3 SPECIFICATIONS Specifications Model CUMMINS QSL9 Type 4-cycle, water-cooled,Direct-injection,Turbo-charger Diesel engine Displacement 8.9 Liters

64

Tower SpecificationsGross Rated Load Table

SPECIFICATIONSSCX3500-3

■Tower 36 m (Rear end Radius: Short)

Unit tonBoom Length (m) neL mooB63 gth (m)

Jib Length (m) neL biJ0342 gth (m)Boom Angle (deg.) Boom Angle (deg.)Radius (m) Radius (m)

10 12.7m x 1021x m4.41t9.792141t4.688.29 41614.186.58 61818.57x m4.026.97 8102x m9.228.07t8.962.47 0222t6.065.668.36 6.76 22423.750.164.75 9.06 42620.254.551.25 8.05 62825.746.05x m3.036.74 4.73 8203x m6.336.346.64t2.737.34 x m3.820323t4.233.040.047.43 3.04 t2.5323439.133.734.031.23 x m4.3343636.927.43x m1.43x m2.938.92 t2.8363836.725.23t8.92t3.228.72 8304x m4.348.52x m2.936.12x m6.930424t0.912.42t2.132.02t3.6224447.81 7.229.8144645.71 x m4.54x m4.5464845.61 t8.12t1.8184

50 15.5 5052 51.2m x 5254 15.0t 54

80 06078806070888

Unit tonBoom Length (m) neL mooB63 gth (m)

Jib Length (m) neL biJ2463 gth (m)Boom Angle (deg.) Boom Angle (deg.)Radius (m) Radius (m)

41x m8.71x m1.614161t5.76t1.6761811.764.17 81029.268.66 02222.95x m3.527.26 2242x m7.728.55t0.351.95 4262t7.647.252.15 8.45 62820.645.947.64 1.05 82032.244.549.24 0.64 03239.839.146.93 4.24 23430.638.83x m0.736.63 3.93 43634.330.63t7.720.43 6.63 6383x m3.041.136.338.62 7.13 9.13 8304t9.320.924.130.52 7.92 x m9.9304246.222.724.923.32 8.72 t0.5224441.125.528.52x m6.749.12 2.62 44648.910.42x m6.54t8.516.02 x m0.546484x m7.156.816.22t3.126.513.91 t4.528405t0.315.713.126.412.81 05259.21 4.61x m8.057.31x m2.1525451.21 5.51t9.029.21t6.7145653.11 7.412.2165856.01 x m0.75x m0.7585060.01 t3.41t8.1106

62 9.4 6264 62.8m x 6466 9.2t 66

80 70 6088 80 70 60 88

* For notes about the table above, refer to page 60.

Page 65: HYDRAULIC CRAWLER CRANE · SCX3500-3 SPECIFICATIONS Specifications Model CUMMINS QSL9 Type 4-cycle, water-cooled,Direct-injection,Turbo-charger Diesel engine Displacement 8.9 Liters

65

Tower SpecificationsGross Rated Load Table

SPECIFICATIONS SCX3500-3

■Tower 36 m (Rear end Radius: Short)

Unit tonBoom Length (m) neL mooB63 gth (m)

Jib Length (m) neL biJ4584 gth (m)Boom Angle (deg.) Boom Angle (deg.)Radius (m) Radius (m)

16 19.5m x 1681x m2.12t2.068102t7.253.95 02223.259.55 22426.948.25 42627.649.94 62829.34x m2.033.74 8203x m6.234.14t1.148.44 0323t6.632.931.83 2.14 23436.431.732.53 1.83 43630.239.436.23 4.53 63837.924.233.03 9.23 83047.722.03x m7.343.82 8.03 04248.523.82t5.024.62 8.82 2444x m0.742.425.623.02 8.42 0.72 4464t6.716.229.420.91 3.32 4.52 64841.713.124.328.71 9.12 0.42 84050.610.020.227.61 6.02 2.12 05250.518.818.02x m9.557.51 5.91 x m4.1525450.417.717.91t5.017.41 4.81 t0.8145652.318.614.715.019.31 4.71 6585x m1.064.218.51x m2.758.9 1.31 x m6.658506t4.86.110.51t2.512.9 4.21 t2.7106268.7 9.012.416.8 7.11 26463.7 3.01x m4.261.8 x m8.2646668.6 7.9 t1.416.7 t4.1166863.6 2.9 1.7 86078.5 x m6.86x m6.8607274.5 t0.9t0.727

74 5.0 7476 74.2m x 7678 5.0t 78

88 80 70 60 88 80 70 60

Unit tonBoom Length (m) neL mooB63 gth (m)

Jib Length (m) neL biJ06 gth (m)Boom Angle (deg.) Boom Angle (deg.)Radius (m) Radius (m)

02x m9.220222t5.0422420.93 42625.63 62823.43 82032.23 0323x m1.533.03 2343t2.237.82 43634.13 1.72 63831.92 7.52 83041.72 4.42 04243.52 3.32 24446.32 2.22 44641.22 2.12 64

48 20.3 20.7 50.4m x 4850 19.4 19.4 15.1t 5052 18.6 18.2 14.3 5254 17.9 17.2 13.4 5456 17.3 16.2 12.5 5658 16.7 15.2 11.7 5860 16.2 14.4 11.0 6062 14.3 13.6 10.3 6264 63.0m x 12.8 9.6 6466 12.7t 12.1 9.0 66

864.8 5.11 86079.7 x m2.8607274.7 t4.1127470.7 4767x m4.476787t9.687

88 80 70

* For notes about the table above, refer to page 60.

Page 66: HYDRAULIC CRAWLER CRANE · SCX3500-3 SPECIFICATIONS Specifications Model CUMMINS QSL9 Type 4-cycle, water-cooled,Direct-injection,Turbo-charger Diesel engine Displacement 8.9 Liters

66

Tower SpecificationsGross Rated Load Table

SPECIFICATIONSSCX3500-3

■Tower 42 m (Rear end Radius: Short)

Unit tonBoom Length (m) neL mooB24 gth (m)

Jib Length (m) neL biJ0342 gth (m)Boom Angle (deg.) Boom Angle (deg.)Radius (m) Radius (m)

10 12.9m x 1021x m6.41t9.192141t4.182.88 41616.779.18 61816.27x m5.124.67 8102x m9.321.86t0.368.17 0222t5.552.463.16 4.66 22422.551.061.55 8.95 42621.056.450.05 7.25 62827.549.946.54 3.93 82030.249.54x m3.238.14 x m5.820323x m7.537.835.14t6.136.83 t6.532343t6.729.539.135.92 7.53 43633.724.33x m3.433.72 x m5.4363834.522.13t3.034.52 t0.5383047.322.92x m2.247.32 04242.22x m3.04t2.71x m7.142444x m4.648.02t9.822.61t3.224464t8.415.911.5164841.41 x m5.741.4184052.31 t7.81x m4.8405254.21 t9.3125

54 11.7 5456 54.2m x 5658 11.6t 58

70 6088 80 70 60 88 80

Unit tonBoom Length (m) neL mooB24 gth (m)

Jib Length (m) neL biJ2463 gth (m)Boom Angle (deg.) Boom Angle (deg.)Radius (m) Radius (m)

14 16.3m x 1416 71.9t 16

818.361.86 81021.061.46 02228.653.06 22426.35x m3.621.75 4262x m8.829.05t4.848.35 6282t5.244.847.44 1.94 82033.045.440.14 1.54 03231.730.148.73 6.14 23433.430.830.53 5.83 43638.133.53x m0.935.23 8.53 63836.929.23t5.322.03 0.33 8304x m4.246.727.037.22 2.82 7.52 0424t1.028.528.821.12 5.62 x m1.0424440.912.427.628.91 9.42 t3.5244647.717.22x m9.545.81 4.32 64846.614.12t3.12x m6.054.71 x m1.6484056.512.02t8.114.61 t3.320525x m7.456.41x m9.153.114.51 2545t5.98.31t1.916.01x m3.3545650.9 0.319.9 t9.4165854.8 2.213.9 85069.7 x m1.958.8 06

62 11.8t 7.3 6264 6.9 6466 65.8m x 6668 6.5t 68

70 6088 80 70 60 88 80

* For notes about the table above, refer to page 60.

Page 67: HYDRAULIC CRAWLER CRANE · SCX3500-3 SPECIFICATIONS Specifications Model CUMMINS QSL9 Type 4-cycle, water-cooled,Direct-injection,Turbo-charger Diesel engine Displacement 8.9 Liters

67

Tower SpecificationsGross Rated Load Table

SPECIFICATIONS SCX3500-3

■Tower 42 m (Rear end Radius: Short)

Unit tonBoom Length (m) neL mooB24 gth (m)

Jib Length (m) neL biJ4584 gth (m)Boom Angle (deg.) Boom Angle (deg.)Radius (m) Radius (m)

16 19.7m x 1681x m4.12t9.458102t8.648.45 02225.644.35 22426.546.05 42627.449.74 62827.24x m2.136.54 8203x m7.337.04t9.735.34 0323t3.339.836.63 7.04 23439.238.638.33 6.73 43634.031.433.13 9.43 63832.827.131.92 5.23 83042.626.921.72 4.03 04244.426.72x m7.544.52 4.82 24448.229.52t4.717.32 7.62 4464x m1.944.123.422.71 3.22 1.52 6484t5.410.028.221.61 9.02 6.32 84050.418.815.121.51 7.91 0.22 05251.317.713.021.41 6.81 x m7.1525452.217.611.912.31 5.71 t2.8145654.117.510.81x m9.854.21 6.61 65857.018.41x m4.75t6.77.11 x m7.7585060.010.41t4.513.7 0.11 t8.5106264.9 2.318.6 3.01 26468.8 x m5.363.6 7.9 46662.8 t7.218.5 x m9.4666867.7 4.5 t5.986072.7 0.5 07

72 70.7m x 7274 7.1t 74

88 80 70 60 88 80 70

Unit tonBoom Length (m) neL mooB24 gth (m)

Jib Length (m) neL biJ06 gth (m)Boom Angle (deg.) Boom Angle (deg.)Radius (m) Radius (m)

02x m1.320222t7.9322422.93 42627.63 62824.43 82033.23 03235.03 2343x m1.638.82 4363t7.922.72 63836.72 8.52 83047.52 5.42 04249.32 3.32 24443.22 2.22 44648.02 2.12 64845.91 3.02 84

50 19.4 18.3 52.4m x 5052 18.7 17.1 12.3t 5254 17.9 16.1 11.6 5456 17.3 15.1 10.8 5658 16.6 14.2 10.1 5860 15.7 13.4 9.4 6062 14.8 12.6 8.7 6264 63.2m x 11.9 8.1 6466 13.0t 11.2 7.6 66

860.7 6.01 86075.6 x m2.9607271.6 t3.0127476.5 47672.5 6787x m5.678708t1.508

80 7088

* For notes about the table above, refer to page 60.

Page 68: HYDRAULIC CRAWLER CRANE · SCX3500-3 SPECIFICATIONS Specifications Model CUMMINS QSL9 Type 4-cycle, water-cooled,Direct-injection,Turbo-charger Diesel engine Displacement 8.9 Liters

68

Tower SpecificationsGross Rated Load Table

SPECIFICATIONSSCX3500-3

■Tower 48 m (Rear end Radius: Short)

Unit tonBoom Length (m) neL mooB84 gth (m)

Jib Length (m) neL biJ0342 gth (m)Boom Angle (deg.) Boom Angle (deg.)Radius (m) Radius (m)

10 13.2m x 1021x m9.41t4.382141t3.472.18 41617.178.57 61814.760.17 81024.36x m5.229.66 0222x m9.429.95t4.755.36 2242t5.059.651.35 1.95 42629.747.351.84 6.35 62827.341.949.34 1.14 82031.041.542.04 x m7.8203230.736.14x m4.431.73 t0.632343x m7.732.432.33t5.623.43 4363t2.328.13x m5.439.42 x m5.5363839.227.92t6.032.32 t4.2383043.127.725.12 04249.91x m3.14x m2.541.02 24446.81t6.62t8.21x m8.344464x m4.944.715.21t9.816484t8.014.616.1184055.01 x m5.948.0105258.9 t6.51x m4.1525452.9 t3.0145

56 8.6 5658 57.2m x 5860 8.3t 60

70 6088 80 70 60 88 80

Unit tonBoom Length (m) neL mooB84 gth (m)

Jib Length (m) neL biJ2463 gth (m)Boom Angle (deg.) Boom Angle (deg.)Radius (m) Radius (m)

14 16.6m x 1461x m3.81t5.466181t2.550.36 81021.455.95 02226.252.65 22428.94x m4.722.35 4262x m8.924.74t2.447.05 6282t1.932.540.34 4.84 82037.832.344.93 6.44 03236.536.043.63 1.14 23439.236.736.33 1.83 43635.039.431.13 4.53 63834.825.23x m1.140.92 0.33 83044.624.03t7.911.72 8.62 0424x m4.447.425.821.91 3.52 x m3.042444t8.611.327.628.71 8.32 t6.5244649.517.129.127.61 4.22 64848.414.02x m1.646.51 x m1.7484059.312.91t6.12x m6.356.41 t6.1205250.311.81t4.87.31 2545x m7.752.21x m9.253.8 9.21 4565t4.64.11t7.717.7 x m3.5565853.6 7.012.7 t4.2185068.5 1.017.6 06264.5 x m1.162.6 2646x m7.36t7.9x m0.364666t0.5t0.666

6088 80 70 60 88 80 70

* For notes about the table above, refer to page 60.

Page 69: HYDRAULIC CRAWLER CRANE · SCX3500-3 SPECIFICATIONS Specifications Model CUMMINS QSL9 Type 4-cycle, water-cooled,Direct-injection,Turbo-charger Diesel engine Displacement 8.9 Liters

69

Tower SpecificationsGross Rated Load Table

SPECIFICATIONS SCX3500-3

■Tower 48 m (Rear end Radius: Short)

Unit tonBoom Length (m) neL mooB84 gth (m)

Jib Length (m) neL biJ4584 gth (m)Boom Angle (deg.) Boom Angle (deg.)Radius (m) Radius (m)

81x m7.128102t0.147.74 02229.046.64 22421.046.54 42623.935.44 62825.834.24 82037.73x m3.235.04 0323x m7.431.63t4.437.83 2343t7.036.431.23 0.73 43632.922.337.92 3.43 63830.725.136.72 9.13 83041.523.927.52 8.92 04244.324.720.42 9.72 24449.127.52x m8.744.22 1.62 44644.021.42t1.410.12 6.42 64

48 23.1 19.7 14.0 22.6 19.2 51.1m x 4850 21.8 18.5 13.1 21.3 18.0 11.9t 5052 51.9m x 17.5 12.2 20.1 16.9 11.5 5254 18.3t 16.5 11.4 19.0 15.9 10.7 54

650.019.419.716.01 5.51 65853.9 1.41x m7.750.01 7.41 85066.8 3.31t5.513.9 x m7.8506260.8 5.217.8 t4.4126465.7 8.112.8 46660.7 x m5.467.7 66865.6 t7.11x m9.6686070.6 t4.707

72 5.6 7274 72.7m x 7476 5.4t 76

88 80 70 88 80 70

Unit tonBoom Length (m) neL mooB84 gth (m)

Jib Length (m) neL biJ06 gth (m)Boom Angle (deg.) Boom Angle (deg.)Radius (m) Radius (m)

02x m4.320222t6.5322424.53 42627.43 62821.43 82035.23 03236.03 2343x m1.739.82 4363t0.723.72 63831.62 9.52 83042.42 6.42 04245.22 4.32 24440.12 3.22 44645.91 3.12 64843.81 3.02 84051.71 5.91 05

52 18.7 16.0 54.5m x 5254 17.9 15.0 9.5t 5456 17.2 14.1 9.0 5658 16.2 13.2 8.3 5860 15.3 12.4 7.7 6062 14.5 11.7 7.1 6264 63.5m x 11.0 6.5 6466 13.0t 10.3 6.0 66

865.5 7.9 86071.5 2.9 0727x m4.07x m3.072747t0.5t1.947

708088

* For notes about the table above, refer to page 60.

Page 70: HYDRAULIC CRAWLER CRANE · SCX3500-3 SPECIFICATIONS Specifications Model CUMMINS QSL9 Type 4-cycle, water-cooled,Direct-injection,Turbo-charger Diesel engine Displacement 8.9 Liters

70

Tower SpecificationsGross Rated Load Table

SPECIFICATIONSSCX3500-3

■Tower 54 m (Rear end Radius: Short)

Unit tonBoom Length (m) neL mooB45 gth (m)

Jib Length (m) neL biJ0342 gth (m)Boom Angle (deg.) Boom Angle (deg.)Radius (m) Radius (m)

10 13.4m x 1021x m1.51t4.272141t8.266.17 41619.162.86 61810.060.46 81022.75x m5.323.06 02222.45t4.252.75 22425.151.15 6.45 42621.642.943.64 5.25 62820.241.742.24 7.24 82035.837.447.83 x m9.8203235.532.146.53 t3.6323439.234.43x m4.639.23 4363x m8.935.03x m7.43t2.225.03 6383t3.914.82t8.039.02 x m6.6383041.916.624.91 t8.9204248.719.420.81 24446.61x m4.248.61 44645.51t5.42x m2.84x m8.5464845.41t0.9t8.518405x m4.256.313.8 0525t3.7x m6.157.7 25459.6 t0.311.7 45653.6 x m4.4565859.5 t0.785

60 5.4 6062 60.2m x 6264 5.4t 64

70 6088 80 70 60 88 80

Unit tonBoom Length (m) neL mooB45 gth (m)

Jib Length (m) neL biJ2463 gth (m)Boom Angle (deg.) Boom Angle (deg.)Radius (m) Radius (m)

14 16.8m x 1461x m5.81t4.456181t2.745.35 81023.640.25 02221.546.05 22420.440.84 42627.24x m4.827.54 6282x m9.037.04t6.047.34 8203t5.539.839.73 9.14 03239.333.739.43 4.04 23432.139.532.23 8.73 43639.823.439.92 1.53 63839.620.238.72 8.23 83040.529.92x m1.349.52 8.72 04244.320.82t4.613.42 x m5.042444x m5.648.123.628.51 7.22 t8.524464t5.315.027.228.41 4.12 64847.212.91x m3.648.31 1.02 84059.111.81t7.129.21 x m1.8405251.110.711.21 t0.0225453.01x m9.35x m6.653.11 45656.9 t1.61t3.56.01 65850.9 0.5 x m4.7585064.8 x m2.85t1.0106268.7 t0.526

64 63.2m x 6466 7.5t 66

88 80 70 60 88 80 70

* For notes about the table above, refer to page 60.

Page 71: HYDRAULIC CRAWLER CRANE · SCX3500-3 SPECIFICATIONS Specifications Model CUMMINS QSL9 Type 4-cycle, water-cooled,Direct-injection,Turbo-charger Diesel engine Displacement 8.9 Liters

71

Tower SpecificationsGross Rated Load Table

SPECIFICATIONS SCX3500-3

■Tower 54 m (Rear end Radius: Short)

Unit tonBoom Length (m) neL mooB45 gth (m)

Jib Length (m) neL biJ4584 gth (m)Boom Angle (deg.) Boom Angle (deg.)Radius (m) Radius (m)

18 20.3m x 1820 40.9t 20

229.532.04 22421.533.93 42624.434.83 62827.335.73 82030.33x m3.333.63 0323x m7.532.23t7.138.43 2343t9.729.038.03 4.33 43636.726.925.82 1.23 63835.525.825.62 0.13 83047.325.726.42 6.92 04240.226.620.32 7.72 24445.022.525.12 0.62 44642.916.32x m8.941.02 4.42 64849.712.22t5.118.81 0.32 84

50 21.7 17.7 11.4 20.9 16.8 53.2m x 5052 18.8 16.6 10.6 19.7 15.8 9.1t 5254 52.1m x 15.7 9.8 18.6 14.8 8.8 5456 18.5t 14.8 9.1 17.6 13.9 8.1 56

855.7 1.31x m9.755.8 9.31 85069.6 3.21t6.519.7 x m7.9506264.6 6.114.7 t3.3126469.5 9.018.6 46664.5 x m5.563.6 6686x m7.76t5.019.5 8607t0.5x m0.960727t7.527

70 88 80 708088

Unit tonBoom Length (m) 54 Boom Length (m)

Jib Length (m) 60 Jib Length (m)Boom Angle (deg.) Boom Angle (deg.)Radius (m) Radius (m)

02x m7.320222t0.1322420.13 42626.03 62820.03 82034.92 03239.82 23433.82 43

36 26.9 38.2m x 3638 25.5 24.8t 3840 24.3 23.2 4042 23.1 21.5 4244 22.0 20.0 4446 21.1 18.7 4648 20.2 17.4 4850 19.3 16.3 5052 18.5 15.2 5254 17.8 14.3 5456 17.1 13.4 5658 16.1 12.5 5860 15.2 11.8 6062 14.4 11.0 6264 63.4m x 10.4 6466 13.3t 9.7 66

861.9 86076.8 0727x m1.172747t3.847

8088

* For notes about the table above, refer to page 60.

Page 72: HYDRAULIC CRAWLER CRANE · SCX3500-3 SPECIFICATIONS Specifications Model CUMMINS QSL9 Type 4-cycle, water-cooled,Direct-injection,Turbo-charger Diesel engine Displacement 8.9 Liters

72

Tower SpecificationsGross Rated Load Table

SPECIFICATIONSSCX3500-3

■Tower 24m Tower Head Hoisting (Rear end Radius: Standard)

Unit ton42

24 30 36 42 48 54 6014 14 14 14 14 14 14Working Radius (m)

5.96789

1012141618

5.96789

1012141618

100.0 100.0 100.0 100.0 100.0 100.0

96.6 70.6

14.8m x62.4t

100.0 100.0 100.0 100.0 100.0 100.0 100.0

77.3 14.8m x

69.0t

100.0 100.0 100.0 100.0 100.0 100.0 100.0

83.7 14.8m x

75.3t

100.0 100.0 100.0 100.0 100.0 100.0 100.0

89.8 14.8m x

81.3t

100.0 100.0 100.0 100.0 100.0 100.0 100.0

95.6 14.8m x

87.0t

100.0 100.0 100.0 100.0 100.0 100.0 100.0

99.3 14.8m x

90.7t

100.0 100.0 100.0 100.0 100.0 100.0

89.4 63.6

14.8m x55.5t

Boom Length (m)Jib Length (m)

Offset angle (deg.)Working Radius (m)

Boom Length (m)Jib Length (m)

Offset angle (deg.)

1. The rated loads are determined according to EN13000 rating on the condition that the machine is stationed on firm level ground.2. To calculate the maximum load that can actually be lifted, deduct mass of all lifting accessories, such as hook, from figures shown above.3. The figures surrounded by bold lines are based on factors other than those which would cause a tipping condition.4. Working radius is the horizontal distance from the swing center to the center of gravity of a lifted load.5. The 145 ton counter weight and 25 ton lower weight are required for all capacities on these charts.

7. The usable hook when lifting tower jib refers "Restriction of Hook Usage" on page 41.

8. Correlation between the number of reeved lines, maximum rated loads, hook mass are shown in the table below.

9. The necessary mass to lower the jib hook refers "Lowerable Jib Hook Mass" on page 42.

6. Figures described as OOm x OOt in the tables indicate "working radius" m x "rated load" ton.

ht (

deducted from the gross rated load of the jib.

Using the unusable hook cause the jib to swing.

Maximum Rated Load (ton)7 falls 6 falls 5 falls 4 falls 3 falls 2 falls 1 fall

HookCapacity

HookMass (ton)

180t

15t

100t45t

100

-

100-

90

-

90-

76

-

76-

61

-

61-

-

-

4645

-

-

3131

-

15

--

3.34

0.62

3.112.17

13. The ross rated load value of the jib with the sheave block the boom top is after 1.1 ton is 12. Remove the sheave block the boom top when using jib length 54 or 60 m for boom length 60 m. 11. Be sure to attach the balance weig 420 kg x 2) to the jib top when the jib length is 24 m.10. The necessary mass to lower the tower head hook refers "Lowerable Tower Head Hook Mass" on page 42.

Page 73: HYDRAULIC CRAWLER CRANE · SCX3500-3 SPECIFICATIONS Specifications Model CUMMINS QSL9 Type 4-cycle, water-cooled,Direct-injection,Turbo-charger Diesel engine Displacement 8.9 Liters

73

Tower SpecificationsGross Rated Load Table

SPECIFICATIONS SCX3500-3

■Tower 42m Tower Head Hoisting (Rear end Radius: Standard)

■Tower 30m Tower Head Hoisting (Rear end Radius: Standard)

Working Radius (m)

Boom Length (m)Jib Length (m)

Offset angle (deg.)Working Radius (m)

Boom Length (m)Jib Length (m)

Offset angle (deg.)

3024 30 36 42 48 54 60

14 14 14 14 14 14 14

56789

101214161820

6.5m x 100.0t 100.0 100.0 100.0 100.0 100.0 100.0

80.4 17.8m x

66.8t

6.5m x 100.0t 100.0 100.0 100.0 100.0 100.0

96.7 77.1

17.8m x63.7t

6.5m x 100.0t 100.0 100.0 100.0 100.0 100.0

91.4 72.1

17.8m x58.8t

6.5m x 100.0t 100.0 100.0 100.0 100.0 100.0

86.0 66.8

17.8m x53.6t

6.5m x 100.0t 100.0 100.0 100.0 100.0 100.0

80.1 61.2

17.8m x48.2t

6.5m x 100.0t 100.0 100.0 100.0 100.0

99.4 74.2 55.5

17.8m x42.7t

6.5m x 100.0t 100.0 100.0 100.0 100.0

92.8 68.1 49.6

17.8m x36.9t

56789101214161820

Unit ton

141414141414 14

36544842 60363024

Working Radius (m)

Boom Length (m)Jib Length (m)

Offset angle (deg.)Working Radius (m)

Boom Length (m)Jib Length (m)

Offset angle (deg.)

Unit ton

6789

1012141618202224

67891012141618202224

7.2m x 100.0t 100.0 100.0 100.0 100.0

99.9 80.3 65.5 53.9

20.8m x49.9t

7.2m x 100.0t 100.0 100.0 100.0 100.0

96.7 77.3 62.5 51.0

20.8m x47.1t

7.2m x 100.0t 100.0 100.0 100.0 100.0

91.9 72.6 58.1 46.6

20.8m x42.7t

7.2m x 100.0t 100.0 100.0 100.0 100.0

86.8 67.8 53.4 42.1

20.8m x38.2t

7.2m x 100.0t 100.0 100.0 100.0 100.0

81.3 62.6 48.4 37.2

20.8m x33.5t

7.2m x 100.0t 100.0 100.0 100.0 100.0

75.9 57.4 43.3 32.3

20.8m x28.6t

7.2m x 100.0t 100.0 100.0 100.0

94.2 70.1 52.0 38.1 27.3

20.8m x23.6t

Working Radius (m)

Boom Length (m)Jib Length (m)

Offset angle (deg.)Working Radius (m)

Boom Length (m)Jib Length (m)

Offset angle (deg.)

42544842 60363024141414141414 14

6789

101214161820222426

6789101214161820222426

7.9m x 90.0t 90.0 90.0 90.0 90.0 90.0 77.9 64.3 53.6 44.4

23.8m x37.4t

7.9m x 90.0t 90.0 90.0 90.0 90.0 90.0 75.5 62.0 51.4 42.2

23.8m x35.3t

7.9m x 90.0t 90.0 90.0 90.0 90.0 87.7 70.5 57.3 46.7 37.8

23.8m x31.0t

7.9m x 90.0t 90.0 90.0 90.0 90.0 82.9 66.0 52.9 42.5 33.6

23.8m x26.9t

7.9m x 90.0t 90.0 90.0 90.0 90.0 78.6 61.9 48.9 38.7 30.0

23.8m x23.3t

7.9m x 90.0t 90.0 90.0 90.0 90.0 72.5 56.1 43.4 33.3 24.8

23.8m x18.2t

7.9m x 90.0t 90.0 90.0 90.0 89.2 67.3 51.1 38.6 28.6 20.3

23.8m x13.8t

Unit ton

* For notes about the table above, refer to page 72.

■Tower 36m Tower Head Hoisting (Rear end Radius: Standard)

Page 74: HYDRAULIC CRAWLER CRANE · SCX3500-3 SPECIFICATIONS Specifications Model CUMMINS QSL9 Type 4-cycle, water-cooled,Direct-injection,Turbo-charger Diesel engine Displacement 8.9 Liters

74

Tower SpecificationsGross Rated Load Table

SPECIFICATIONSSCX3500-3

Working Radius (m)

Boom Length (m)Jib Length (m)

Offset angle (deg.)Working Radius (m)

Boom Length (m)Jib Length (m)

Offset angle (deg.)

48544842 60363024141414141414 14

789

1012141618202224262830

7891012141618202224262830

8.6m x 76.0t 76.0 76.0 76.0 76.0 76.0 63.7 53.0 44.1 36.5 30.0

26.8m x27.8t

8.6m x 76.0t 76.0 76.0 76.0 76.0 74.4 61.0 50.4 41.7 34.1 27.7

26.8m x25.5t

8.6m x 76.0t 76.0 76.0 76.0 76.0 70.3 57.0 46.5 38.0 30.5 24.2

26.8m x22.0t

8.6m x 76.0t 76.0 76.0 76.0 76.0 66.0 53.0 42.6 34.1 26.8 20.6

26.8m x18.3t

8.6m x 76.0t 76.0 76.0 76.0 76.0 61.3 48.4 38.2 29.9 22.8 16.6

26.8m x14.5t

8.6m x 76.0t 76.0 76.0 76.0 73.2 56.8 44.1 34.0 25.8 18.8 12.8

26.8m x10.6t

8.6m x 76.0t 76.0 76.0 76.0 67.1 51.0 38.5 28.7 20.6 13.8

7.9 26.8m x

5.8t

Unit ton

89

101214161820222426283032

Working Radius (m)

Boom Length (m)Jib Length (m)

Offset angle (deg.)Working Radius (m)

Boom Length (m)Jib Length (m)

Offset angle (deg.)

54544842 60363024141414141414 14

9.3m x 61.0t 61.0 61.0 61.0 61.0 60.6 50.5 42.2 35.3 29.4 24.2

29.8m x20.0t

89101214161820222426283032

9.3m x 61.0t 61.0 61.0 61.0 61.0 58.1 48.1 39.9 33.1 27.3 22.1

29.8m x17.9t

9.3m x 61.0t 61.0 61.0 61.0 61.0 54.6 44.6 36.5 29.7 24.0 18.9

29.8m x14.7t

9.3m x 61.0t 61.0 61.0 61.0 61.0 50.1 40.3 32.3 25.6 20.0 14.9

29.8m x10.8t

9.3m x 61.0t 61.0 61.0 61.0 58.8 46.8 37.1 29.2 22.6 17.0 12.0

29.8m x7.9t

9.3m x 61.0t 61.0 61.0 61.0 53.7 41.9 32.3 24.6 18.1 12.6

7.7 29.0m x

5.0t

9.3m x 61.0t 61.0 58.7 52.4 46.3 37.8 28.4 20.8 14.3

8.9 27.6m x

5.0t

Unit ton

Unit ton

32

89

1012141618202224262830

3436

891012141618202224262830323436

Working Radius (m)

Boom Length (m)Jib Length (m)

Offset angle (deg.)Working Radius (m)

Boom Length (m)Jib Length (m)

Offset angle (deg.)

604842363014141414

9.9m x 61.0t 61.0 61.0 61.0 61.0 55.4 45.9 39.2 32.3 26.5 21.6

13.1 17.1

32.8m x11.6t

9.9m x 61.0t 61.0 61.0 61.0 61.0 51.4 42.0 35.3 28.6 22.8 18.0

9.6 13.6

32.8m x8.1t

9.9m x 61.0t 61.0 61.0 61.0 58.7

48.0 38.7 31.9 25.3 19.6 14.8

6.5 10.5

32.8m x5.1t

9.9m x 61.0t 61.0 61.0 56.1 50.5 44.1 35.0 28.2 21.6 16.1 11.3

7.1 31.0m x

5.0t

* For notes about the table above, refer to page 72.

■Tower 48m Tower Head Hoisting (Rear end Radius: Standard)

■Tower 54m Tower Head Hoisting (Rear end Radius: Standard)

■Tower 60m Tower Head Hoisting (Rear end Radius: Standard)

Page 75: HYDRAULIC CRAWLER CRANE · SCX3500-3 SPECIFICATIONS Specifications Model CUMMINS QSL9 Type 4-cycle, water-cooled,Direct-injection,Turbo-charger Diesel engine Displacement 8.9 Liters

75

Weights and Dimensions of Disassembled UnitsWeights and Dimensions List TECHNICAL DATA SCX3500-3

Weights and Dimensions of Disassembled UnitsDescription Qty Dimensions (mm) Weight (kg)

Front revolving frame+ rear revolving frame

MastJacks

Boom hoist winch (including rope)

1

2985

2990

12300

6050

3275

3670

1480

1440

49250

Front revolving frame+ rear revolving frame

MastBoom hoist winch(including rope)

without:Jacks

1

12300

6050 2990

3275

3670

1480

1440

46600

Front revolving frameJacks

without:Mast

Boom hoist winch (including rope)

1

74206050

1495

1440

3280

2990

34650

Front revolving framewithout:

MastJacks

Boom hoist winch (including rope)

1

74206050

1495

1440

3280

2990

32000

Rear revolving frameMast

Boom hoist winch(including rope)

1

9780

3510 2905

445

2240

14600

Crawler sideframe 2

10500

1250

1800

1815

30200

Jack beam 4

1455440

1125

560

Weights and Dimensions of Disassembled UnitsWeights and Dimensions List

*Stands are for temporary placement only. Use the receiver stand size of when transporting.

Comply with the regulations when transporting."Weight" refers to the mass of each single unit.

Page 76: HYDRAULIC CRAWLER CRANE · SCX3500-3 SPECIFICATIONS Specifications Model CUMMINS QSL9 Type 4-cycle, water-cooled,Direct-injection,Turbo-charger Diesel engine Displacement 8.9 Liters

76

Weights and Dimensions of Disassembled UnitsWeights and Dimensions ListTECHNICAL DATASCX3500-3

Weights and Dimensions of Disassembled UnitsDescription Qty Dimensions (mm) Weight (kg)

Counter weight (Base) 1

780

4557120

2490

19700

Counter weight 14

1850515

2300

8950

Lower weight(For counter weight 145 t

specifications)2

4370

1920

860

12500

Lower step 2

591012

6026

0

280

HB9.5 ; 9.5 mBoom base

W1, W2, W4 Winch1

2765

2970

10350395

21800

H6 ; 6 mBoom insertConnect pinBar pendant

(Boom support 6 m andrear strut support 6 m)

1

6160 2485

2490

2700

H6B ; 6 mBoom insert BConnect pinBar pendant

(Boom support 6 m andrear strut support 3m)

1

2485

2490

6160

2700

H9 ; 9 mBoom insertConnect pinBar pendant

(Boom support 9m andrear strut support 9m)

1

2485

2490

9160

3800

*Stands are for temporary placement only. Use the receiver stand size of when transporting.

Page 77: HYDRAULIC CRAWLER CRANE · SCX3500-3 SPECIFICATIONS Specifications Model CUMMINS QSL9 Type 4-cycle, water-cooled,Direct-injection,Turbo-charger Diesel engine Displacement 8.9 Liters

77

Weights and Dimensions of Disassembled UnitsWeights and Dimensions List TECHNICAL DATA SCX3500-3

Weights and Dimensions of Disassembled UnitsDescription Qty Dimensions (mm) Weight (kg)

HR7 ; 7 mReducer

Connect pinBar pendant

(Boom support 7m andrear strut support 7m)

1

2670

2495

7160

3500

HT1.5 ; 1.5 mBoom top 1

4410

2950

2490

5400

LB8 ; 8 mTower/luffing jib base 1

2495

1880

8240

3120

L6 ; 6 mTower/luffing jib insert

Connect pinPendant

1

1990

1880

6120

1500

L9 ; 9 mTower/luffing jib insert

Connect pinPendant

1

1990

1880

9120

2000

LT7 ; 7 mTower/luffing jib top 1

2025

2280

2040

9685

3400

For boom topAux. sheave block 1

1785

825

1210

610

Crane jib basewith jib strut

Connect pin attached7.8 m pendant attached

1

6680 1085

1405

1280

Page 78: HYDRAULIC CRAWLER CRANE · SCX3500-3 SPECIFICATIONS Specifications Model CUMMINS QSL9 Type 4-cycle, water-cooled,Direct-injection,Turbo-charger Diesel engine Displacement 8.9 Liters

78

Weights and Dimensions of Disassembled UnitsWeights and Dimensions ListTECHNICAL DATASCX3500-3

Weights and Dimensions of Disassembled UnitsDescription Qty Dimensions (mm) Weight (kg)

Crane jib top 1

10656955

1390

770

Crane jib insertConnect pin attached 1

6090 1085

1090

320

7.8 m pendant 2

811177896

58

5.85m pendant 2

5938

74

100

75

1.65m pendant 2

1650

74

100

18.4

Front strutRear strut 1

11790 1770

2085

7800

Tower/luffing jib top tip roller 2

1950

780

685

530

Tower/luffing jib top weight 2

1520

485

100

420

Page 79: HYDRAULIC CRAWLER CRANE · SCX3500-3 SPECIFICATIONS Specifications Model CUMMINS QSL9 Type 4-cycle, water-cooled,Direct-injection,Turbo-charger Diesel engine Displacement 8.9 Liters

79

Weights and Dimensions of Disassembled UnitsWeights and Dimensions List TECHNICAL DATA SCX3500-3

Weights and Dimensions of Disassembled UnitsDescription Qty Dimensions (mm) Weight (kg)

350 t Hook 1

1490790

2845 4440

180 t Hook 1

2545

810 1150

3340

100 t Hook 1

2160

790 900

3110

45 t Hook 1

790

1970

730

2170

15 t Hook 1

355

1500

355

620

Page 80: HYDRAULIC CRAWLER CRANE · SCX3500-3 SPECIFICATIONS Specifications Model CUMMINS QSL9 Type 4-cycle, water-cooled,Direct-injection,Turbo-charger Diesel engine Displacement 8.9 Liters

80

Equipment List Standard and Optional EquipmentTECHNICAL DATASCX3500-3

Equipment List Standard and Optional Equipment

: Standard : Optional : No setting

Item Crane Crane / Tower

Lower Structure

1250 mm ShoeJack BeamCrawler Sideframe Connection UnitStepsShoe Tension Unit (Shim Adjusting Type)

Upper Structure

Cab Up/Down CatwalkUnder Cover (Bed Lower Surface)Working Light (×2)Back Mirror (Left / Right)Flip CylinderAuto Idle StopEco ModeHandrails (Inserting Type)

Cab

Tilt Cab (0 to 15°)Air ConditionerSunvisorSunshade Wiper with Washer (Front Window, Cab Roof Window)Microphone & Loud-speakerAM / FM Radio (with Clock)Room LampCup Holder24 V Power Socket (×2)Floor CarpetLevel Gauge (in Cab)Accelerator GripDrum Rotation Sensor [Front (W1) / Rear (W2) / Boom Hoist (W3) / Jib Hoist (W4)]*1

Speed Control Dial [Front (W1) / Rear (W2) / Boom Hoist (W3) / Jib Hoist (W4)]*1

Arm Chair LeverAccelerator Pedal (Right Side)Boom Hoist Operation PedalSwing Brake Operation PedalFanFuel Burning HeaterLife Hammer

Attachment

24m Basic Boom (HB9.5: 9.5m Boom Base, HR7: 7m Reducer, H6B: 6m Boom Insert B, HT: 1.5m Boom Top)H6: 6m Boom Insert (Including Boom Steps, Skywalk, Stanchion)H9: 9m Boom Insert (Including Boom Steps, Skywalk, Stanchion)Auxiliary Sheave for Crane (1 Sheave) [Including Auxiliary Sheave, Anti-two Block]24m Tower Jib (LB8: Tower/Luffing Jib Base: 8m, L9: 9m Tower/Luffing Jib Insert, LT7: Tower/Luffing Jib Top: 7m)L6: 6m Jib InsertL9: 9m Jib InsertAuxiliary Sheave for Tower Jib (1 Sheave) [Including Auxiliary Sheave, Anti-two Block]Parts Set for 13.0m Crane Jib (6.5m Jib Base, 6.5m Jib Top)6.0m Crane Jib InsertHammer Head only for 350t Lifting [Including Anti-two Block]Boom Foot Pin Removal / Installation Cylinder350t Hook (14 Sheaves)180t Hook (7 Sheaves)100t Hook (3 Sheaves)45t Hook (1 Sheave)15t Hook

Wire Rope

Front (W1) Winch ( 28)Rear (W2) Winch ( 28)Boom Hoist (W3) Winch ( 28)Jib Hoist (W4) Winch ( 28)

*1 Jib hoist (W4) is not included in the crane specification.

Page 81: HYDRAULIC CRAWLER CRANE · SCX3500-3 SPECIFICATIONS Specifications Model CUMMINS QSL9 Type 4-cycle, water-cooled,Direct-injection,Turbo-charger Diesel engine Displacement 8.9 Liters

81

Equipment List Standard and Optional Equipment TECHNICAL DATA SCX3500-3

: Standard : Optional : No settingItem Crane Crane / Tower

Safety Device

Moment Limiter3 Color Percentage Indicator LightGate Lock LeverIndividual Winch Operation Lever Lock [Front (W1), Rear (W2),Boom Hoist (W3), Jib Hoist (W4), Travel]Automatic Drum Lock [Boom Hoist (W3), Jib Hoist (W4)]Winch Drum Lock [Front (W1), Rear (W2)]Swing LockSwing AlarmTravel AlarmAuto Slowdown (Slow Stop)Boom Hoist Limiting DeviceSecondary Boom Overhoist Prevent DeviceWarning AlarmEngine Start Interlock SystemEmergency Engine Stop Switch (In cab)Lifting Height Indication DeviceSwing Neutral Free/Brake Selection SwitchAnti-two BlockTower/Luffing Jib Overhoist Prevention DeviceSecondary Tower/Luffing Jib Overhoist Prevention DeviceSwing Restriction UnitAnemometer (HH 1.5)Anemometer (HT 1.5)Anemometer (LT 7)Crane Boom Top Camera Monitor SystemTower/Luffing Jib Top Camera Monitor SystemDrum and Rear View Monitor System (× 7)Cab Roof Window Guard / *2 / *2

Others

Boom Back StopBoom Angle SensorBoom Lifting PieceRemote Sensing (Mobile Communication Terminal, Data Logging Device)Assembly PadQuick Draw for Side Frame Self AssemblyExternal Hydraulic PowerHandy Cylinder for Connecting BoomBracket for Coupling CylinderGuide Roller for Nesting BoomReduction Counter Weight Specification *3 *3

Reeving Winch (4 × F(30) 8mm × 250m)Sling Ropes for Disassembly and Assembly (Belt Sling, Sling Wire, Shackle)HB9.5: 9.5m Boom Base Side FootingToolbox (Left and Right Sideframes Attached)Additional Spare Parts (Hydraulic Oil Filter)Additional Tools (Large Hammer, Crowbar, Chisel)Standard Supplied ToolsStandard Spare Parts

*2 Europe specification machines only.*3 The reduction counter weight specification can only be used for the crane specification, with the exception of the crane jib.

Page 82: HYDRAULIC CRAWLER CRANE · SCX3500-3 SPECIFICATIONS Specifications Model CUMMINS QSL9 Type 4-cycle, water-cooled,Direct-injection,Turbo-charger Diesel engine Displacement 8.9 Liters

M E M OSCX3500-3

Page 83: HYDRAULIC CRAWLER CRANE · SCX3500-3 SPECIFICATIONS Specifications Model CUMMINS QSL9 Type 4-cycle, water-cooled,Direct-injection,Turbo-charger Diesel engine Displacement 8.9 Liters
Page 84: HYDRAULIC CRAWLER CRANE · SCX3500-3 SPECIFICATIONS Specifications Model CUMMINS QSL9 Type 4-cycle, water-cooled,Direct-injection,Turbo-charger Diesel engine Displacement 8.9 Liters

• We are constantly improving our products and therefore reserve the right to change designs and specifications without notice. • Units in this specification are shown under International System of Units; the figures in parenthesis are under Gravitational System of Units as old one.

9-3, Higashi-Ueno 6-chome, Taito-ku, Tokyo 110-0015, JapanPhone: 81-3-3845-1387 Facsimile: 81-3-3845-1394http://www.hsc-cranes.com