2
13 AWNING HINGES 1 These hinges balance a sash as it opens for smooth, effortless operation. The stainless steel reinforced shoe provides continuous smooth action. Detachable support arms allow quick installation of the sash into the frame. It is recommended to match the size of the hinge to the height and weight of the sash. Each size hinge is designed to balance a particular size and weight sash. Proper selection of a hinge can help prevent problems such as “window chatter” that are sometimes experienced when these hinges are used with Truth's Awning Operators. An adjustable friction screw allows one to customize ease of window movement. Table within the drawings gives a recommended height and weight range for each hinge. The data in this table has been generated by computer simulation as a guide in matching the hinge with the window. If you have a sash that doesn’t appear on this table, call Truth for selection assistance. WARRANTY: Protected under the terms of the Truth Warranty for Window and Door Manufacturers and Authorized Distributors. Refer to Truth’s Terms and Conditions for further details. MATERIAL: Steel track. Heavy gauge steel support arms and acetal shoe with stainless steel insert. Corrosion resistant non-magnetic stainless steel package is also available. FINISH: Truth’s E-Gard® Hardware has a multi-stage coating process that produces a superior physical and aesthetic finish. Plus, it is resistant to a wider range of corrosive materials, including industrial cleaning materials and environmental pollutants. This proprietary process has been tested to be approximately three times better than common zinc plated finishes. ORDERING INFORMATION: 1. Choose hinge size desired (specify by part number). 2. Specify right- or left-hand (determined by the hinge side when looking at the window from the outside). 3. Hinges can be ordered assembled or K.D. (knocked down). K.D. hinges allow track and arm assemblies to be purchased separately for greater efficiency when hardware is applied to sash and frames in separate locations. 4. Optional mounting hardware: #20585 - Adjustment screw, included with hinge. Replacement pieces sold separately. #30591 - Detach clip, included with hinge. Replacement pieces sold separately. RECOMMENDED SCREWS: Type of screws required determined by material of profile being used. Refer to drawings for complete information on screw type and quantity needed (sold separately). TRUTH TIPS: 1. Special consideration should be given when designing an awning window. Please consult Truth Tech Note #2 for further information. 2. Failure of the concealed awning hinge can occur under certain situations when opened to near 90º. For this reason, an operator and/or limit device must be used with the concealed awning hinge to prevent the window from being opened to 90º. 3. When an awning window is “under hinged” (i.e., when a hinge is used on a window larger than what it is recommended for), two areas of concern are created. First, chatter is likely to occur when operated with an awning operator (see Truth Tips for Awning Operator). Second, depending on the degree of under hinging, the hinge may fail at an amount of opening significantly less than 90º. For this reason, the amount of opening must be limited to 45º of opening, any #13 series Awning Hinge may be used on sash up to 42 inches high and 61 lbs. 4. Adding a snubber to the center of the top rail on an awning window may increase the negative air pressure rating of the window. See Snubber section for proper application. 5. For vinyl window applications, mounting screws should pass through two PVC walls or one PVC wall and one insert wall. For this reason, it may be necessary to use a longer screw than is recommended. 6. To insure maximum screw thread engagement in vinyl profiles, a #7 screw with an undercut head should be used for mounting the Track (not available from Truth). 7. For accurate hardware placement in vinyl or metal applications, pre-drilling is recommended. 8. For metal window profiles Truth recommends machine screws however, in most applications sheet metal screws will provide adequate holding power. 9. When selecting mounting screws for Truth hardware, coating compatibility is one of the most important criteria. For best corrosion resistance the coating on the screws should be the same as the coating on the hardware. For more information, see Tech Note #11. INCLUDE TRUTH SPECS IN YOUR NEXT WINDOW PROJECT Sash balancing friction hinge for use on residential or commercial windows, which will be concealed between sash and fame for low maintenance and clean exterior aesthetics. Awning window hinges shall be of sash balancing design, which provides a friction screw adjustment for fine tuning window sash operation. Constructed of E-Gard® components to provide enhanced corrosion protection. Awning window hinges shall be 13 Series hinge, as manufactured by Truth Hardware, Owatonna, MN. AWNING

HW01 Awning Hinge

Embed Size (px)

DESCRIPTION

These hinges balance a sash as it opens for smooth, effortless operation. The stainless steel reinforced shoe provides continuous smooth action. Detachable support arms allow quick installation of the sash into the frame.Available from http://whcparts.ca

Citation preview

Page 1: HW01 Awning Hinge

13 AWNING HINGES

1

These hinges balance a sash as it opensfor smooth, effortless operation. Thestainless steel reinforced shoe providescontinuous smooth action. Detachablesupport arms allow quick installationof the sash into the frame.

It is recommended to match the size ofthe hinge to the height and weight ofthe sash. Each size hinge is designedto balance a particular size and weightsash. Proper selection of a hinge canhelp prevent problems such as“window chatter” that are sometimesexperienced when these hinges are usedwith Truth's Awning Operators. Anadjustable friction screw allows one tocustomize ease of window movement.

Table within the drawings gives arecommended height and weight rangefor each hinge. The data in this tablehas been generated by computersimulation as a guide in matching thehinge with the window. If you have asash that doesn’t appear on this table,call Truth for selection assistance.

WARRANTY:Protected under the terms of the TruthWarranty for Window and DoorManufacturers and AuthorizedDistributors. Refer to Truth’s Termsand Conditions for further details.

MATERIAL: Steel track. Heavygauge steel support arms and acetalshoe with stainless steel insert.Corrosion resistant non-magneticstainless steel package is also available.

FINISH: Truth’s E-Gard® Hardwarehas a multi-stage coating process thatproduces a superior physical andaesthetic finish. Plus, it is resistant to awider range of corrosive materials,including industrial cleaning materialsand environmental pollutants. Thisproprietary process has been tested tobe approximately three times betterthan common zinc plated finishes.

ORDERING INFORMATION:1. Choose hinge size desired (specify by part number).

2. Specify right- or left-hand(determined by the hinge side whenlooking at the window from the outside).

3. Hinges can be ordered assembled orK.D. (knocked down). K.D. hingesallow track and arm assemblies to bepurchased separately for greater

efficiency when hardware is applied tosash and frames in separate locations.

4. Optional mounting hardware:#20585 - Adjustment screw, includedwith hinge. Replacement pieces soldseparately. #30591 - Detach clip,included with hinge. Replacementpieces sold separately.

RECOMMENDED SCREWS:Type of screws required determined bymaterial of profile being used. Referto drawings for complete informationon screw type and quantity needed(sold separately).

TRUTH TIPS:1. Special consideration should begiven when designing an awningwindow. Please consult Truth TechNote #2 for further information.

2. Failure of the concealed awninghinge can occur under certainsituations when opened to near 90º.For this reason, an operator and/orlimit device must be used with theconcealed awning hinge to prevent thewindow from being opened to 90º.

3. When an awning window is “underhinged” (i.e., when a hinge is used on a window larger than what it isrecommended for), two areas ofconcern are created. First, chatter islikely to occur when operated with anawning operator (see Truth Tips forAwning Operator). Second, dependingon the degree of under hinging, thehinge may fail at an amount of openingsignificantly less than 90º. For thisreason, the amount of opening must belimited to 45º of opening, any #13series Awning Hinge may be used onsash up to 42 inches high and 61 lbs.

4. Adding a snubber to the center ofthe top rail on an awning window mayincrease the negative air pressure rating

of the window. See Snubber sectionfor proper application.

5. For vinyl window applications,mounting screws should pass throughtwo PVC walls or one PVC wall andone insert wall. For this reason, it maybe necessary to use a longer screw thanis recommended.

6. To insure maximum screw threadengagement in vinyl profiles, a #7screw with an undercut head should beused for mounting the Track (notavailable from Truth).

7. For accurate hardware placement invinyl or metal applications, pre-drillingis recommended.

8. For metal window profiles Truthrecommends machine screws however,in most applications sheet metal screwswill provide adequate holding power.

9. When selecting mounting screws forTruth hardware, coating compatibilityis one of the most important criteria.For best corrosion resistance the coatingon the screws should be the same as thecoating on the hardware. For moreinformation, see Tech Note #11.

INCLUDE TRUTH SPECS INYOUR NEXT WINDOW PROJECTSash balancing friction hinge for useon residential or commercial windows,which will be concealed between sashand fame for low maintenance andclean exterior aesthetics.

Awning window hinges shall be of sashbalancing design, which provides afriction screw adjustment for fine tuningwindow sash operation. Constructed ofE-Gard® components to provideenhanced corrosion protection.

Awning window hinges shall be 13Series hinge, as manufactured by TruthHardware, Owatonna, MN.

AWNING

Page 2: HW01 Awning Hinge

13 AWNING HINGES

1a

APPLICATION OF CONCEALED AWNING HINGE

L

F

N/A

N/A

N/A

N/A

2.625

FRAME

SASH

(12.7mm) .500

B C D E

(12.7mm) .500

(11.1mm) .438

.4375 (111.1mm) BOTTOM

HOLE ONLY

1.250 (31.8mm)

MOUNTING HOLES EQUALLY

SPACED ON 4.000

(101.6mm) CENTERS

13.13 SHOWN

CLOSED POSTION SHOWN

AVAILABLE OPERATORS

HINGE NO.

LEVER OPERATOR

AWNING OPERATOR

ENTRYGARD DUAL ARM *

ENTRYGARD DYAD *

SPLIT ARM *

23 SERIES DYAD *

22 SERIES PIVOT SHOE

22 SERIES SCISSOR

ARM

13.13

13.14

13.15

13.16

13.17

13.43

13.44

13.42

13.45

10.14

10.10

N/A

10.14

10.11

10.14

11.12,11.30

11.10,11.12

11.14,11.16

11.14,11.30

11.32

11.29,11.32

11.27,11.21

11.28

22.17,22.18

22.10

N/A N/A

N/A N/A

N/A

22.22 THRU 22.29

15.10,15.61 15.16

15.14,15.75

15.11,15.62 15.18,15.66

ALL 23

SERIES

N/A N/A 15.19 AR

M M

AT

ER

IAL

ST

ST

EE

L S

TE

EL

* OPERATOR IS MOUNTED ON THE SIDE JAMB

HINGE

STEEL ST.STL

RECOMMENDED SASH HEIGHT

RECOMMENDED MAXIMUM

SASH WEIGHT HINGE

LENGTH

L B C D E

SCREWS REQ'D

PER HINGE

13.13

13.14

13.15

13.16

13.17

13.43

13.44

13.42

13.45

N/A

10.0-14.0 (254.0mm-355.6mm)

14.0-19.0 (355.6mm-482.6mm)

19.0-26.0 (482.6mm-660.4mm)

26.0-34.0 (660.4mm-863.6mm)

34.0-42.0 (863.6mm-1066.8mm)

7 LBS (3.2 KG)

20 LBS (9.1 KG)

38 LBS (17.3 KG)

50 LBS (22.7 KG)

61 LBS (27.7 KG)

10.0 (254.0mm)

14.0 (355.6mm)

18.0 (457.2mm)

22.0 (558.8mm)

26.0 (660.4mm)

6.250 (158.8mm)

8.250 (209.6mm)

10.250 (260.4mm)

11.75 (298.4mm)

4.250 (108.0mm)

6.250 (158.8mm)

8.250 (209.6mm)

1.250 (31.8mm)

2.625 (66.7mm)

5.438 (138.1mm)

7

8

9

10

12

RECOMMENDED SCREWS: (P/N 119110.XX) NO.7X .750 PHILLIPS, FLAT HEAD, SHEET METAL SCREWS (STEEL) (P/N 19105.XX) NO. 7X .750 PHILLIPS, FLAT HEAD, SHEET METAL SCREWS (STAINLESS STEEL)

FOR USE WITH TRACK ON PVC: NO. 7X .750 PHILLIPS, FLAT HEAD, UNDERCUT, SHEET METAL SCREWS(NOT AVAILABLE FROM TRUTH, QUANTITIES WILL DEPEND ON HINGE) (SEE TRUTH TIP NO. 5&6)

(11.1mm) .438

(31.8mm) 1.250

(11.1mm) .438

(18.3mm) .719

700 WEST BRIDGE STREET, OWATONNA, MN 55060 ■ 507.451.5620 800.866.7884 ■ TRUTH.COM