BACKING ALERT with AUTO SPEED LOCK

This product functions with select TOYOTA vehicles only. See Vehice Compatibility Chart.Visit our website for the absolute latest information on vehicle compatibility.

Thank you for purchasing the HV-300 Backing Alert System. Please read this manual inits entirety before using the product. Be sure to store this manual in a safe place, as you may need to reference it in the future.

MODEL FRAME NO. YEARSAI (1)AQUA / Prius CVITZ / YarisCamry (1)Corolla AXIO (&HV)Corolla FIELDER (&HV)NOAH (&HV)Harrier (&HV) (1)

Prius PHVPriusα / Prius v / Prius+

AZK10NHP10P13#AVV50E16#E16#GR8#U6#W

ZVW35ZVW4#W

2009(DEC.) & newer

(1) This vehicle comes with a factory-installed Auto Speed Lock function.

NOTE: Cars newer than the above that have been altered by the car maker may be incompatible.

NOTE: Cars built outside Japan have not been confirmed by us and could be incompatible.

Compatible cars must have Smart Key!

Full Version Chart

2011 Dec. ~ 2015 Oct.2010 Dec. ~ 2015 Jun.2011 Sep. ~ 2015 Sep.2012(MAY.) & newer2012(MAY.) & newer2014 Jan. ~ 2015 Dec.2013(DEC.) & newer

2012(JAN.) & newerPrius ZVW30 2009 May. ~ 2015 Dec.

2011(MAY.) & newer

WARNING!This product is not waterproof or dust-proof. Never install in the engine compartment. Never install where water can pool or where oil, dirt and grime could enter and cause an electrical short.

PRODUCT WARRANTY CLAIMHV-300TOYOTA Backing Alert System

1 YEAR (validated only by dealer and/or dated proof of purchase)

Year: , Month: , Day:

Name:Address:

Phone: Email:

Name:Address:

Phone: Website:

Approval StampManufacturer:

Contact TEL:

KIRAMEK, Inc.9-183-1 Itayama-cho, Handa-shi, Aichi-Ken 475-0936 JAPAN

+81-569-20-5585 ( )Operating Hours (ex. Sat./Sun./Holidays):10:00AM ~ NOON, 1:00PM ~ 4:00PM

PRODUCT DESC.:

Warranty Period:

Date of Purchase*:

Customer Info.*:

* Please fill in these marked sections above completely.

NOTE: Warranty Claims not accepted without valid Approval Stamp and/or dated proof of purchase.

Seller Info.*:

MODEL:

Operational Voltage

Absolute Max./Min. VoltagesCurrent Consumption

Oper. Ambient Temp. Range (no condensation)

+12Vdc

< 4.5mA (while CAN sleeping)

PRODUCT SPECIFICATIONSTOYOTA COMPATIBILITY (Partial)

HV-300 USER GUIDE

®

Ver. 02032016

PRECAUTIONSPLEASE READ THOROUGHLY BEFORE USE

The included wire harness and connectors are specially made for the HV-300 only. Please do not splice off the CAN or POWER wires, and do not use this harness or connector with any other device; otherwise, a short, fire, or vehicle breakdown may occur.

WARNING

NOTE Product or vehicle failure could result from ignoring the following:

• This product is primarily intended for use on Japanese vehicles within Japan.• Modifying this product voids the warranty and could cause harm to your car or yourself.• Never mount this product to vehicles other than shown in our Compatibility Chart. Japanese vehicles made outside Japan may be incompatible.• NEVER store or mount this product where water, oil, dirt, or moisture collects, or where there is intense heat or steam present as such may cause product failure. This product is not dust-proof, waterproof or splash-proof.• Our company shall not be held liable for traffic accidents that occur with or without the presence of this product.• Specifications of this product are subject to change without notice. • ALWAYS confirm that your installer has appropriate expertise and equipment to safely and properly install this product.• We have confirmed this product functions correctly when used with other DIGI-LINK products, but we cannot guarantee compatibility when used with third party OBD CAN-BUS devices. Such devices may malfunction or may cause malfunction in the HV-300, or may even cause a vehicle warning light to come on.• ALWAYS secure the product and wiring in a professional manner such that nothing loose could be caught or smashed by something in the car, become lodged behind the foot pedals, or could cause an electrical short or fire or bodily harm.

MAIN FEATURES• Detects Ignition state and Gear Position. An alert will sound when in Reverse Gear (unless disabled by DIP switch or Disable Switch). • Backing Alert can be Enabled and Disabled by Disable Switch and by DIP Switch. The default DIP Switch setting is ENABLED.• Pressing the Disable Switch button lights its LED and temporarily disables the back alert beeping sound. To re-enable, simply press the Disable Switch button again, or switch the engine OFF then ON. (When the LED is not lit, the backing alert beep is enabled.) • Two types of BEEPS can by chosen for the Backing Alert via DIP Switch (Long or Short).• When Enabled via DIP SW (default), doors automatically LOCK when the vehicle speed increases beyond 20km/h (approximately).• The UNLOCK trigger (for Auto Speed-Lock) can be set by DIP Switch. The default setting LOCKs when you return the gear to the “P” position.• Rapid deceleration (hard braking) will trigger the Emergency UNLOCK feature. Doors Unlock 9 seconds after you brake hard, when travelling 20km/h or faster. (This is not guaranteed in a traffic accident where all electrical power is lost.)

WARRANTY TERMS

1) Warranty period is measured as one (1) year from date of purchase.2) In the unlikely event of product failure during normal use (as defined by this manual), the product will be repaired or replaced free of charge, but only at the original dealer/place of purchase. Demand for onsite repairs may be met in some cases within Japan, but onsite service fees will apply and vary by location.3) All warranty claims must be submitted through the vendor from whom you originally purchased this product. You must fill out the form on the front page of this manual, and submit the dated purchase receipt.4) You can only submit warranty claims to us if you have moved and can no longer visit your HV-300 dealer.5) Customer bears the cost of removal/reinstallation fees, as well as return shipping if not hand-delivered.6) Regardless of being covered under Warranty, the following cases resulting in malfunction will require a fee: • Oil, water, dust, etc. having accumulated inside and on the electronics. • Improper installation or carelessness by the user. • Unauthorized product repair or modification. • Accidental drops, falls or other strong impact. • Fire, earthquake, flood, lightening, tornadoes, other natural disasters, as well as pollution, salt-air damage, etc. • When used outside the intended use, as specified in this manual. • Car accidents, vandalism or theft. • Problems due to deficiencies in this manual, or if you do something this manual doesn’t specifically prohibit. • And cases where you do not properly fill out your claim, provide false info., and/or lack a dated receipt.7) This warranty is only valid for HV-300 users outside Japan with express written approval from KIRAMEK.8) We cannot reissue printed documents free of charge. Please keep this document safe and do not lose it.

Product repair or replacement is guaranteed under the terms, conditions and duration of this warranty. This warranty does not limit your legal rights. If you have questions or problems after this one (1) year warranty has expired, please consult with the original dealer from whom you purchased the HV-300 product. Because your warranty claim will be invalidated by an improperly filled out PRODUCT WARRANTY CLAIM card, please carefully confirm all entries and/or consult with your HV-300 dealer before submission.

PLEASE NOTE:

DIP Switch #6 must be used as shown below to enable the HV-300 to function on the chosen car. (DIP Switches #1 ~ #5 should have been set for your car in Step-1.)

NOTE: When the above steps are finished, you never need to do them again forthe same car, even if you disconnect the OBD plug, change your car’s battery, etc.But if you move the HV-300 to a different compatible car, you need to repeat the above steps.

1ON

2 3 4 5 6

Turn on the Ignition.

Make sure all 3 connectors are plugged into the Controller.(2 for Disable Switch, 1 for OBD Harness)

Flip DIP SW #6 to ON.6

Flip DIP SW #6 to OFF.6

FINAL SETUP3

OBD plug: choosing which side wires exit

Connect to the car’s OBD as shown above.

You can choose whichside the wires exit.

HV-300 WIRE HARNESS

OBD PIN-OUTS

Color Description+12VGND

CAN-HICAN-LO

REDBLK

BRNBRN/RED

pin16pin14CAN-LO +12V

GROUND CAN-HIpin6pin4

OBD CONNECTION2

9

1

9

1

If you already used theincluded wire-tie, you willneed to remove it so you can slide off the OBD cap.

NOTE: When finished, securethe wires to the tab on the cap using a small wire-tie.Slide off the

cap as shown.

Pull wires to the opposite side and put cap on as shown.

9

1

NOTE: If the vehicle’s OBD plug is already being used or if there is no space to attach the HV-300’s OBD plug, you can either purchase our optional OB-22 extender harness, or you can purchase our Posi-Tap connector 4-pack (p/n NT-4.) We don’t recommend soldered connections. You would be surprised to know how many badly soldered connections result in problems!

4-STEP INSTALLATION

Connect the HV-300’s OBD2 plug to the car’s OBD2 plug.2

Set vehicle compatibility DIP switch to match your car.

Use DIP SW#6 to confirm CAN signal compatibility.

Refer to “DIP SWITCH SETUP” below.

Refer to “OBD CONNECTION” below.

Refer to “FINAL SETUP” below.

1

3

Mount the Control Module and Disable Switch.Refer to “MOUNTING CONTROLLER & DISABLE SW” below.

4

DIP SWITCHES

The location of the DIP switches is shown in the diagram at right.

All switches are set to OFF (all UP) by default,as shown:

DIP SWITCH SETUP1

1ON

2 3 4 5 6

SW4

SW3

SW2

SW1

DIPSW No. FUNCTION

No function. Do not touch. Leave set to OFF state.

Backing Alert Beep Length

Backing Alert Function

Speed-Lock Function

UNLOCK Trigger

One-time use only switch. See “FINAL SETUP” below.

SW5

SW6

OFF = Short Beep ON = Long Beep

OFF = EnabledON = DisabledOFF = EnabledON = DisabledOFF = “P” GearON = Ignition OFF

After completing Steps 1~3, mount the HV-300 controller as shown. Ensure it does not interfere with foot pedals or the car’s moving parts. Mount the Disable Switch with the included 2-sided tape whereever you can conveniently push the button and view the LED.

MOUNTING CONTROLLER & DISABLE SW4

Driver’s Kick Panel

Area above driver’s kick panel

WARNING! This product is not waterproof or dust-proof. Never install in the engine compartment. Never install where water can pool or where oil, dirt and grime could enter and cause an electrical short.

Location shown at left is simply one recom- mended location for the controller. Use wire-ties to mount the controller. Never obstruct foot pedals or other vehicle parts!

INCLUDED PARTS Controller

Disable Switchwith LED

OBDHarness

Harness Length: 1mHarness Length: 1m

4