Huminator humidity generator - Testo · Sell Huminator along with Testo humidity products. slide 9. Pneumator pressure calibrator and measuring instrument. TIS calibrators – Huminator

slide 1

TIS calibrators – Huminator and Pneumator

Huminatorhumidity generator

slide 2

Huminator – humidity generator from TIS

technical data:

temperature range °C +15…+40

temperature accuracy °C +/- 0.5 (10…85%RH at +25°C)

temperature stability °C +/- 0.2(10…85%RH at +25°C)

humidity range %RH 5…95

humidity accuracy %RH +/- 2 (10…85%RH at +25°C)

humidity stability %RH +/- 1 (10…85%RH at 25°C)

dimensions (D*W*H) mm 350*470*200

weight (net) kg 14.5

slide 3


general important information

- use only destilled water in the water tube on the back;necessary to generate higher humidities than the ambient air

- never move or transport the Huminator with filled water tube / tank;the water may destroy the motherboard and get into the evaporator

- the Huminator has got a drying container incl. drying reagent on the back; necessary to dry the air to generate lower humidities than the ambient air has

- a calibration in the Huminator requires a reference system;e.g. a DKD-calibrated t650 or t400 with 1%-reference probe

slide 4


Drying container and drying reagent

- it is necessary to dry the drying reagent from time to time

- an indication is either when the colour changes, (from orange to white)or if it is not possible to generate humidities lower than ambient conditions

- the procedure to dry the reagent is described in the manual

But be careful: do only dry the reagent, not the complete container!

Regeneration

The granules should be removed from the column and spreadevenly, one granule deep, on a tray. Heat for one hour at about210°C up to 230°C or 400°F up to 445°F. The desiccant shouldthen be cooled in a tight container before refilling the acrylic unit.Felt filters should also be pre-dried at 100°C for about 30 minutesbefore assembly. Specify the acrylic model of the LABORATORYGAS DRYING UNIT. Please consider the regulations according tothe safety data sheet of the respective substance.

picture: broken container

slide 5


Water in the chamber

- could occur in every generator running in high humidity and/or temperature ranges over a long time

- if the chamber is not stable anymore, there is only one chance:interrupt the calibration, open the front plate and clean the chamber with a cloth

- to avoid this, do not cool from high to low temperatures in a fast way!

slide 6


adjustment of the Huminator

Adjustment at 11.3%RH and 75.3%RH at +25°C:

- it could be necessary to adjust the Huminator from time to time

- it is also very important to use a reference system for the adjustment to generate exactly 11.3%RH respectively 75.3%RH at +25°C

- the adjustment procedure is also described in the manual

Enter Button 11.3%RH Button

75.3%RH Button

slide 7


calibration procedure in the Huminator- regulate the temperature first until it is stable,

then turn on the humidity regulation to the desired value

- always start with the lowest temperature and/or humidity value

- set and save up to 5 different temperature / humidity combinations (pic.1)

- set up a time program up to 3 different temperature and humidity values (pic.2)

- program a wait time for each calibration point (pic.3)

pic. 1 pic. 2 pic. 3

slide 8


Huminator – good sale success in your country

Sell Huminator along with Testohumidity products

slide 9

Pneumatorpressure calibrator and

measuring instrument

TIS calibrators – Huminator and Pneumator

slide 10

Pneumator – pressure calibrator and measuring instrument

calibrate differential pressure – in the lab or on-site

- differential and gauge pressure probes with low Pascal up to 1 bar range- air velocity/volume flow: not directly calibratable but differential pressure calibration

e.g. testo 521, 512 or any other differential pressure measuring instrument- choose between „CTRL“-mode (step-by-step) or „AUTO-mode “ (defined sequence)- very short adjustment time (just a few seconds)- high mobility: useable for 8 hours without mains supply (incl. pump function)

or

slide 11

- differential pressure in cleanrooms- filter pressure and ventilator pressure- mode „MESS“- accuracy +/- 0.3 % of final value at 0..100 Pa! - accuracy +/- 0.1 % of final value at > 100 Pa up to 1 bar!


highly precise differential pressure measuring

slide 12


highly precise measuring of air velocity and volume flow

- air velocity and air volume flow measurements- mode „VELO“ or „FLOW“- directly displayed as air velocity- or volume flow-unit!

∆p = p2 – p1

v (m/s) = s * (2 * ∆p / rho)

V (m3/s) = A * s * (2 * ∆p / rho)

p1 = static pressure

p2 = dynamic pressure

slide 13


for example: Prandtl Pitot tube testo 0635.2145

- length 300 mm- diameter 4 mm- tube factor = 1,0 (Prandtl)

measuring range Pneumator maximum velocity

up to 100 Pa 1…12 m/s

up to 1 000 Pa 4…40 m/s

up to 10 000 Pa 7…70 m/s

up to 100 000 Pa Not applicable

slide 14


the measuring cell inside the Pneumator: inductive and innovative

Magneticallycoated on both sides

workscompletelyfrictionless

movement of thecell causesinductance

changes on bothsides

concentricwaved

membrane

slide 15


the control elements

slide 16


Ordering information

Pneumator 1 hPa10 hPa100 hPa1000 hPa

0519.08160519.08170519.08180519.0819

Accessories transport case

ISO calibration certificate, 5 points

DKD calibration certificate, 11 points

0519.0849

0520.0025

0520.0215

included in delivery multi voltage power supply unit1m silicone tube

Price EUR 4,100

slide 17


The shown standard packaging is EUR 31.90

slide 18


Instead of the standard packaging, the stable transport case can be ordered.

- protection for any transport- get to the customer in a

professional way

EUR 390

slide 19


flexibel, precise, mobile – the features at a glance

- flexibel: can be used either as a calibrator or as a measuring instrument

- high precision even in low Pascal-range

- long-run rechargeable battery for mobile applications

- highly stable zero-point by automatical adjustment

- fast supply of gauge- and differential-pressure while

- programmable pressure sequences

- wide choice of pressure-, volume flow-, and velocity units

- English/German menu

Documents

Huminator humidity generator - Testo · Sell Huminator along with Testo humidity products. slide 9. Pneumator pressure calibrator and measuring instrument. TIS calibrators – Huminator