HULL SURVEY SHEET FOR DISTRIBUTION LIST CDTL - original

HULL SURVEY SHEET FOR HMCS Montreal

DISTRIBUTION LIST CDTL - original copy ENG/NAO/Hull Survey Office - file copy

COMPONENT

PAINT AND PRESERVATION

LOCATIONS: UPPER DECKS STEM TO TRANSOM 1 DK AND ABOVE PORT, STBD & C/L

FRAME DECK SIDE

DEFECTS AND JUSTIFICATION 1. ANNUAL PAINT AND PRESERVATION SURVEY OF UPPER DECKS – 2015.

REFS: A. DRMIS No. 820311810 B. HI-23-003-005/JI-001, Dated 31 OCT 2013 C. HI-23-003-005/JI-003, Dated 31 OCT 2013 (Refs B and C located at: http://halifax.mil.ca/n4nem/fmfcs/engdpt/nao/csindex.htm)

REF DWG NO.:

DESCRIPTION OF WORK REQUIRED

HULL SURVEYOR:

APPROVED BY:

HI REPORT NO.: HS150189 REVISION: 1 SURVEY SHEET NO.: PAGE 1 OF 8

CG.HEDDON PH 427-3885 H. LANKESTER PH 427-3578

SURVEY DATE: 27 APRIL 2014

1. An FMFCS/ENG/NAO/Hull Surveyor has conducted the Annual Paint and Preservation Survey of the exterior non-

slip and painted decks for the 2015 Paint and Preservation season. 2. The following are the results of the survey:

a. Quarter Deck – the coating is in poor condition, Non-Skid is lifting in areas extensive bleed through showing

in most areas with numerous areas of mechanical damage and bollards are in poor condition 100 percent renewal of coating is required

b. Flight Deck – the coating is in good condition, minor repairs to areas of mechanical damage in non-traffic areas only;

c. Hangar – the coating is in poor condition, extremely dirty, many areas have no coating due to ongoing repairs

100% renewal of coating required;

d. STBD Hangar Lobby – the coating is in good condition, no repairs required;

e. Port Hangar Lobby – the coating is in good condition, no repairs required;

f. Port Boat/Missile Deck – the coating is in good condition, some staining exists and there are several isolated areas of mechanical damage to the non-skid and non-traffic areas, bollards are in extremely poor condition limited repairs to be conducted;

g. STBD Boat/ Missile Deck - the coating is in good condition, some staining exists and there are several

isolated areas of mechanical damage to the non-skid and non-traffic areas, bollards are in extremely poor condition limited repairs to be conducted;

h. Port Passageway – the coating is in good condition, with some areas of slight mechanical damage no

repairs required at this time;

i. Foc’sle – the coating is in poor condition, the deck is littered with coating patch repairs, , the deck was Intercryled in 2011, and patched and repaired in 2013 and 2014, areas of non-traffic around stanchion bases failing 100% renewal of coating required;



COMPONENT



FRAME DECK SIDE



REF DWG NO.:


HULL SURVEYOR:

APPROVED BY:




j. Port Bridge Wing – the coating is in good condition, no repairs required;

k. STBD Bridge Wing – the coating is in good condition, no repairs required;

l. Flag Deck – the coating is in very poor condition, several areas of deterioration to bare metal, heavily stained 100% coating renewal required;

m. Port Hangar Side Deck – the coating is in poor condition, 100% coating renewal required;

n. STBD Hangar Side Deck – the coating is in fair condition, 100% coating renewal required;

o. Bridge Top - the coating is in poor condition, there are large areas that require non-skid that are currently

treated as non-traffic areas from mods during MLR, and several patches from mods during MLR, staining showing through, requires; 100% coating renewal required;

p. Hangar Top - the coating is in good condition, no repairs required;

q. ECM Top/ FAMR Casing Top – the coating is in poor condition 100% coating renewal required;

r. Funnel Flat – the coating overall is in good condition with one area STBD Fwd corner having a localized

coating failure, limited repairs required;

s. DRES BALL Flat – the coating is in fair condition, repairs required along edges under grating and scattered areas throughout ; and

t. Funnel Top – the coating is in good condition, no repairs required.



COMPONENT



FRAME DECK SIDE



REF DWG NO.:


HULL SURVEYOR:

APPROVED BY:




3. Decks requiring 100% renewal of coating:

a. Hangar Interior, FR 39 – 47.5, 1 deck. IAW Ref B, clean/degrease/clean to bare metal IAW surface preparation Method 3, cleaning to bare metal IAW SSPC-SP-12-WJ-1 Standards and treat;

. Total traffic area (non-skid): 139 sq meters (1494 sq ft)

Total non-traffic area: 16.6 sq meters (179 sq ft)

Total surface area: 155.6 sq meters (1673 sq ft)

(1) included to be cleaned/degreased/cleaned to bare metal IAW surface preparation Method 3, cleaning to bare metal IAW SSPC-SP-12-WJ-1 Standards and treat as per existing colour scheme are the following;

(a) six (6) sumps; and (b) forward PORT and STBD passages;

b. Fos’cle, FR Stem– 12, 1 deck, clean and treat deck 100% as per Ref B using surface preparation Method 3,

SSPC-SP-12-WJ-1 Standard Ultra High Pressure Water Jet blast and treat: Total traffic area (non-skid): 309 sq meters (3322 sq ft). Total non-traffic area: 58.3 sq meters (627 sq ft). Total surface area: 367.3.3 sq meters (3953.5 sq ft). (1) included to be cleaned/degreased/cleaned to bare metal IAW surface preparation Method 2, cleaning to

bare metal IAW SSPC-SP-11 Standards and or surface preparation Method 3, SSPC-SP-12-WJ-1 Standard Ultra High Pressure Water Jet blast and treat as per existing colour scheme are the following;



COMPONENT



FRAME DECK SIDE



REF DWG NO.:


HULL SURVEYOR:

APPROVED BY:




eight (8) sets of bollards, and anchor cable deck penetrations, covers and cartage save all. An additional 24 sq meters of non-traffic area has been added to include these items.

c. Quarter Deck, FR 59 to Transom, 1 deck, C/L. IAW Ref B, clean/degrease/clean to bare metal IAW surface preparation Method 3, cleaning to bare metal IAW SSPC-SP-12-WJ-1 Standards and treat; Total traffic area (non-skid): 101.6 sq meters (1092 sq ft) Total non-traffic area: 25.5 sq meters (274.5 sq ft) Total surface area: 127.1sq meters (1368 sq ft) (1) included to be cleaned/degreased/cleaned to bare metal IAW surface preparation Method 2, cleaning to

bare metal IAW SSPC-SP-11 Standards and or surface preparation Method 3, SSPC-SP-12-WJ-1 Standard Ultra High Pressure Water Jet blast and treat as per existing colour scheme are the following;

The raised section aft of the flight deck all bollards, roller fairleads and towing cleat, an additional 18 sq meters of non-traffic area has been added to include these items.

d. Flag Deck, FR 24.5 – 25.5, 01 deck. clean and treat deck 100% as per Ref B using surface preparation Method 3, SSPC-SP-12-WJ-1 Standard Ultra High Pressure Water Jet blast, and treat: Total traffic area for repair (non-skid): 7 sq meters (75 sq ft). Total non-traffic area: 13 sq meters (140 sq ft). Total surface area: 20 sq meters (215 sq ft). (1) removals to include but not limited to three (3) ammo locker(s) and two (2) flag locker(s). Lockers to be

reinstalled upon completion complete with new fasteners IAW original arrangement.



COMPONENT



FRAME DECK SIDE



REF DWG NO.:


HULL SURVEYOR:

APPROVED BY:




e. ECM Top / FAMR Casing Top, FR 20.5 – 24, 03 deck: clean and treat deck 100% as per Ref B using surface preparation Method 3, SSPC-SP-12-WJ-1 Standard Ultra High Pressure Water Jet blast, and or surface preparation Method 2, cleaning to bare metal IAW SSPC-SP-11 Standards and treat; Total traffic area (non-skid): 33.2 sq meters (357 sq ft). Total non-traffic area: 4 sq meters (43 sq ft). Total surface area: 37.2 sq meters (400 sq ft).

f. Bridge Top Deck, FR 12-20.5, 02 deck, C/L: clean and treat deck 100% as per Ref B using surface preparation Method 3, SSPC-SP-12-WJ-1 Standard Ultra High Pressure Water Jet blast, and treat: Total traffic area for repair (non-skid): 138.1 sq meters (1485 sq ft). Total non-traffic area: 16 sq meters (172 sq ft). Total surface area: 154.1 sq meters (1657 sq ft).

g. Port Hanger Side Deck, FR 39-45, 01 Deck, Port. : clean and treat deck 100% as per Ref B using surface preparation Method 3, SSPC-SP-12-WJ-1 Standard Ultra High Pressure Water Jet blast, and treat: Total area to be cleaned to SSPC-SP-1 Standards: 40 sq meters (430 sq ft). Total traffic area for repair (non-skid): 15 sq meters (161 sq ft). Total non-traffic area: 25 sq meters (269 sq ft).

h. Stbd Hanger Side Deck, FR 39-45, 01 Deck, Stbd. clean and treat deck 100% as per Ref B using surface preparation Method 3, SSPC-SP-12-WJ-1 Standard Ultra High Pressure Water Jet blast, and treat: Total area to be cleaned to SSPC-SP-1 Standards: 40 sq meters (430 sq ft). Total traffic area for repair (non-skid): 15 sq meters (161 sq ft).



COMPONENT



FRAME DECK SIDE



REF DWG NO.:


HULL SURVEYOR:

APPROVED BY:




Total non-traffic area: 25 sq meters (269 sq ft).

4. Decks requiring partial repairs: NOTE: All decks listed below have been previously coated with International products and shall be repaired and top coated with International products.

a. STBD Boat/Missile Deck, FR 22.5 – 40, 1 deck. Clean/degrease 100% of the of the deck and treat deteriorated areas of coating IAW paras 18 – 20 of Ref C: Total traffic area: 4 sq meters ( 43 sq ft)

Total non-traffic area for repair: 6 sq meters (65 sq ft)

Total surface area to be top coated: 0 sq meters (0 sq ft) (1) All bollards to be cleaned to bare metal IAW para 18 of ref C and treated IAW Para 5 of this Hull Survey.

b. PORT Boat/Missile Deck, FR 22.5 – 40, 1 deck. Clean/degrease 100% of the of the deck and treat deteriorated areas of coating IAW paras 18 – 20 of Ref C:

Total traffic area: 4 sq meters ( 43 sq ft) Total non-traffic area for repair: 6 sq meters (65 sq ft) Total surface area to be top coated: 0 sq meters (0 sq ft)

(1) All bollards to be cleaned to bare metal IAW para 18 of ref C and treated IAW Para 5 of this Hull Survey.



COMPONENT



FRAME DECK SIDE



REF DWG NO.:


HULL SURVEYOR:

APPROVED BY:




c. Flight deck, Fr 47.5 – 59, 1 Deck. Clean/degrease 100% of the deck and treat deteriorated areas of

coating IAW paras 18 – 20 of Ref C: Total traffic area for repair (non-skid): 0 sq meters (0 sq ft) Total non-traffic area: 4 sq meters (43 sq ft) Total surface area: 0 sq meters (0 sq ft)

(1) Curtain plate is main area of mechanical damage with tie downs and non-traffic area along track openings

d. DRES Ball deck (FER Uptakes 02F2), FR29-32, 02 Deck, CL; clean/degrease 100% of the DRES BALL Flats, clean areas exhibiting corrosion/loose and flaking/deteriorated coating to bare metal IAW SSPC SP-11 and treat/repair IAW Ref C, para 18, 19 and 20 (polyurethane colour black);

Total area to be cleaned to SSPC-SP-1 Standards: 133 sq meters (1432 sq ft). Total area to be cleaned to bare metal and treated: 5 sq meters (54 sq ft). Total area to be top-coated: 0 sq meters (0 sq ft).

e. Funnel Flat deck (AER Casing 1GA), FR32-35, 01 Deck, C/L; clean/degrease 100% of the Funnel Flat, clean areas exhibiting corrosion/loose and flaking/deteriorated coating to bare metal IAW SSPC SP-11 and treat/repair IAW paras 18 – 20 of Ref C:

Total traffic area for repair (non-skid): 3 sq meters (32.3 sq ft)

Total non-traffic area: 4 sq meters (43 sq ft)

Total surface area: 0 sq meters (0 sq ft)

(1) Area of concern is Stbd Fwd corner localized failure non-Skid and Non traffic coating is lifting.



COMPONENT



FRAME DECK SIDE



REF DWG NO.:


HULL SURVEYOR:

APPROVED BY:




5. Upon completion of cleaning to bare metal all bollards/fair leads/roller fair leads are to be treated as follows: a. all working surfaces (where the rope is touching/slipping), apply one (1) coat of coat of Code C420 to a DFT of 4 – 5 mils; and b. to all non-working surfaces apply coating system as per Ref C, paras 18 - 20 colour as per existing colour scheme.

6. Removals required to facilitate above repairs are to be determined by the Repair Facility (RF).

7. Areas in way of repairs are to be certified “gas free” and “safe for hot work”.

8. Necessary staging is to be supplied by the RF.

9. The RF shall remove, handle, store, transport and dispose of all hazardous waste in accordance with all applicable

Federal, Provincial and Municipal regulations and legislation. Precautions shall be taken during cleaning and painting to protect the ship’s equipment and the environment from contamination. Coatings may contain heavy metals such as lead and chromates therefore solid waste, for example paint chips, shall be leachate tested to determine appropriate disposal option. The RF shall provide a Disposal Certificate if any waste material is classed as Hazardous Waste.

10. Precautions shall be taken to prevent damage and contamination from the ingress of dust, dirt, cleaning debris and

paint splatter. Blank and seal all openings, inlets, and outlets, protect (wrap and seal) all equipment, fittings, windows, sidelights, tally plates, electrical lighting etc. subject to damage. Protect all non painted surfaces and equipment from damage and paint splatter, i.e. plastic laminates, rubber products (hoses, shock mounts, expansion pieces, door/hatch/flap gaskets) and damage control (DC) markings.

11. All surface preparation, coating application, inspections and required OQE documentation shall be IAW Refs B, C,

CFTO D-23-003-005/SF-002 and this Hull Survey Report. 12. Any conflicts regarding this work instruction shall be brought to the attention of the FMFCS/ENG/NAO/Hull

Surveyors’ Office for resolution.

) ~ Fleet Maintenance ~ ;)_ Facility Cape Scott ....::!~ 1ii'll JIIJ· .

H 1-23-003-005/J 1-001 Amended 31 OCTOBER 2013

STANDARD FMF CAPE SCOTT JOB INSTRUCTION SURFACE PREPARATION AND COATING APPLICATION PROCEDURE

APPLICABLE TO ALL CLASS SHIPS

NON-SLIP AND PAINTED DECKS

LOCATION VARIOUS

(Supersedes Dated 06 March 2012) Approved By: NAO/SNR HS

Originator: NAO/HULL SURVEY Contact: NAO/HULL SURVEY Phone: 427-3885

NEI NUMBER:

PURPOSE:

E-28-418-000 (HFX CLASS) E-28-175-000 (I RO CLASS) E-28-672-BOO (PTR CLASS)

This specification states the requirements for the surface preparation and coating application for non-slip and painted decks.

RELATED DOCUMENTS:

D-23-003-005/SF-002

C-39-003-00 1 I AG-001

C-70-328-000/MP-001

SSPC-SP-1

SSPC-SP-11

SSPC-SP-5

SSPC-SP WJ-1/NACE WJ -1




SSPC-VIS-1

SSPC-VIS-3

SSPC-PA-2

SSPC-TU-4

NACE RPO 287-95

ASTM D-4285

SSPC PAINTING MANUAL

DWG 0251110

DWG HFX-D28-396-000-01 I

SHTS 7, 8, AND 9 DWG 0151097

C-02-040-009/AG-000

A-GG-040-001 /AG-001

SPECIFICATION FOR MAINTENANCE PAINTING OF HMC SHIPS

HELICOPTER/SHIP INTERFACE DESIGN GUIDANCE AND CLEARANCE CRITERIA MANUAL THIRD LINE MAINTENANCE INSTRUCTION FOR VERTICAL LAUNCH SYSTEM- LAUNCHER TOP RESURFACING SOLVENT CLEANING

POWER TOOL CLEANING TO BARE METAL

WHITE METAL BLAST CLEANING

JOINT SURFACE PREPARATION STANDARD WATERJET CLEANING OF METALS - CLEAN TO BARE SUBSTRATE (WJ-1) JOINT SURFACE PREPARATION STANDARD WATERJET CLEANING OF METALS- VERY THOROUGH CLEANING (WJ-2) JOINT SURFACE PREPARATION STANDARD WATERJET CLEANING OF METALS-THOROUGH CLEANING (WJ-3) JOINT SURFACE PREPARATION STANDARD WATERJET CLEANING OF METALS- LIGHT CLEANING (WJ-4) VISUAL STANDARD FOR ABRASIVE BLAST CLEANED STEEL

VISUAL STANDARD FOR POWER AND HAND TOOL CLEANED STEEL

MEASUREMENT OF DRY COATING THICKNESS

FIELD METHODS FOR RETRIEVAL AND ANALYSIS OF SOLUBLE SALTS ON SUBSTRATE NACE STANDARDS, FIELD MEASUREMENT OF SURFACE PROFILE OF ABRASIVE BLAST CLEANED STEEL SURFACES INDICATING OIL AND WATER IN COMPRESSED AIR

VOLUME 2, 2005 EDITION

FLIGHT DECK MARKINGS IRQ CLASS

PAINTING AND PRESERVATION SCH, (MARKINGS) HFX CLASS

FLIGHT DECK AND HANGAR MARKINGS, PTR CLASS

DND SAFETY LEGISLATION AND POLICY

DND SAFETY POLICY AND PROGRAMS

OCCUPATIONAL SAFETY AND HEALTH PART 11, CANADA LABOUR CODE

OCCUPATIONAL SAFETY AND HEALTH, POLICY VOLUME OF THE TB MANUAL

THE CANADIAN ENVIRONMENTAL PROTECTION ACT

THE CANADIAN FISHERY ACT

ANNEX(ES):

ANNEX A

ANNEX B

ANNEXC

PREPARATION AND TREATMENT RECORDING FORM

CHLORIDE ION TESTING RECORDING FORM

NAVAL SPECIFICATION MATERIAL LIST (NSML)

2

H 1-23-003-005/J 1-001

DESCRIPTION OF WORK

The Repair Facility (RF) shall carry out the following work:

Scope

1. The intent of this specification is to provide instructions for the surface preparation and the coating application of a non-slip and/or painted deck coating system on interior/exterior steel and aluminum decks.

2. The work involves the following:

a. cleaning the entire specified area to remove all loose flaking coatings, salts, grease, dirt, visible contaminants and soluble contaminants, followed by cleaning the entire specified area to bare metal lAW SSPC-SP-5 and I or SSPC-SP-11 Standards and I or SSPC-SP WJ-1 Standards;

b. applying an Epoxy Primer System to bare metal areas; followed by

c. the application of a Type 1, Comp G, LSA Epoxy Non-slip Deck Coating (traffic areas) and a Exterior Alkyd Marine Enamel Topcoat (non-traffic areas) .

NOTES:

(1) The method of cleaning to bare metal shall be determined by the FMFCS/ENG/NAO/Hull Surveyor at time of survey and shall be recorded I specified in the Hull Survey report or any other relevant documentation(s) I specification(s) in which this Jl has been attached.

(2) The work specified in this Job Instruction shall not be considered to be the only requirement for the coating repairs. Any additional coating repairs I work required in addition to this Job Instruction shall be as specified in the Hull Survey report or any other relevant documentation in which this Jl has been attached.

(3) The RF shall have a NACE CIP Levell I Coating Inspector on staff to carry out all coating inspections and record all applicable data as detailed within the specification.

(4) A FMFCS/ENG/NAO/Hull Surveyor NACE CIP Level II Coating Inspector (also referred as FMFCS NACE Inspector) shall witness all inspections as detailed within the specification. The frequency and level of involvement of the FMFCS NACE Inspector will be left to the discretion of the FMFCS NACE Inspector.

Precautions

3. Take precautions during the pre-surface preparation, surface preparation, pre-treatment and painting period to contain all cleaning material, waste water, airborne blasting material , grit and debris as not to contaminate the ships interior compartments and the atmosphere where equipment is stationed. Provide temporary protection to prevenfdamage and over-spray to ship's structure, equipment and fittings as required .

a. temporarily cover and seal furnishings, electrical and electronic equipment. Close ventilation inlets and outlets, doors, windows and hatch openings. Temporarily blank or plug drain openings and pre-wet nozzles during cleaning and painting to prevent the ingress of water, dust, dirt, grit, paint fumes, etc.

b. take precautions during coating removal operations as coating may contain heavy metals such as lead and chromates. Leachate test solid waste, (i.e. the paint chips}, to determine appropriate disposal option. Disposal of all hazardous waste shall be in accordance with all applicable municipal, provincial and federal regulations and

3

REMARKS

c

H 1-23-003-005/JI-001 legislation. A Disposal Certificate shall be provided to the designated DND Representative (i.e. NDQAR, CONO Overseer, Technical Services Supervisor) if the waste material from the blast cleaning operation is classed as hazardous waste.

Scheduling/Deck Protection

4. Schedule deck preparation and painting work in high traffic areas or decks subject to other work during low activity periods. Isolate sources of contamination including pedestrian traffic. Cordon off deck areas and post OUT OF BOUNDS signs as necessary. Protect all deck coverings from damage unti l they are serviceable for traffic or until the end of the work period.

Parameters of Traffic and Non-traffic Areas

5. Prior to coating removal, the RF shall record the traffic (non-slip areas) and non-traffic (dado I painted areas) for reference. Non-traffic areas are normally inaccessible to traffic, (i.e. under fixed shelving, desks, lockers, benches and equipment foundations) . All coamings, deck fittings, exposed seatings and a minimum of 50mm (2 inches) around their perimeter are considered non-traffic areas. The top of flush hatches shall have non-slip coating applied with a 50mm (2 inch) perimeter painted boundary.

Temporary Sheltering

6. To maintain environmental conditions (for deck preparations and coating application) and to protect the environment (ref. Fisheries Act, Section 35), the RF shall:

• Totally enclose the decks being cleaned I prepared 100% to bare metal lAW SSPC-SP-5 Standards (white metal blast) treat in a manner that would prevent the dispersion of particles into the air or release of any deleterious substances into the harbour. The RF shall capture and dispose of all used I drained liquids in accordance with all applicable municipal, provincial and federal regulations and legislation.

• For decks I areas only requiring partial repairs and I or top-coat, install appropriate protection I hoarding I containment in a manner that will prevent the dispersion of particles into the air or release of any deleterious substances into the harbour. The RF shall capture and dispose of all used I drained liquids in accordance with all applicable municipal, provincial and federal regulations and legislation.

• Sweep I clean I scrape all areas of loose and I or flaking coatings to remove as much loose debris as possible and collect and dispose appropriately prior to cleaning to SSPC-SP-1 Standards (Solvent Cleaning) .

• Cleaning products sb<:~ll be used I mixed I diluted in accordance with manufacturer's recommendations I instructions.

• Coatings shall be applied by means of rollers and/or paint brushes to reduce VOC emissions and prevent over-spray into the water and I or atmosphere. If decks are fully enclosed I hoarded, spray application may be permitted.

• All enclosures I protection I hoarding shall be erected I installed to the satisfaction of FMFCS Safety I Environment personnel prior to the commencement of any work; and all enclosures I protection I hoarding shall be maintained to the satisfaction of FMFCS Safety I Environment personnel while in use for the duration of the paint coating project. Paint, paint chips or dust generated during paint removal shall not be permitted to enter the water. Containment booms shall be in place prior to the commencing any work, and any spillage shall be cleaned. Spill response kits for first level intervention shall be available on site for the duration of the coating I re-surfacing project.

• The ambient air temperature and substrate temperatures during coating application and curing must be maintained within the coating manufacturer's recommended values. If required, provide a temporary shroud (for weather protection) or a fully enclosed shelter

4

R

NC*

H 1-23-003-00SIJ 1-001 (cold weather) , to fully cover the boundaries of the deck area being treated. During cold weather, the ambient temperature inside the enclosure shall be maintained 24 hours per day at a minimum of r C. The designated DND Representative (i.e. NDQAR, CONO Overseer, Technical SeNices SupeNisor) and I or FMFCS NACE Inspector shall inspect shelter.

• All work shall be carried out in accordance with labour and environmental regulations within the jurisdiction that the work is carried out in.

Interference Removals

7. Interference removals required to gain access to all areas of the deck requiring coating repairs are to be determined by the RF during the viewing period. Areas requiring repairs are to be determined by the FMFCS NACE Inspector. Removals identified in this Job Instruction or any other relevant documentation(s) I specification(s) are only listed to assist the RF in bidding and are not to be considered all-inclusive or limited to those items listed.

a. Tag, disconnect, ease away or remove and retain all interference items clear of the work area, and suitably protect against damage. On completion of repairs, reinstall and re-secure items, utilizing with new fasteners, in accordance with the existing arrangement. On completion of re-installation, all disturbed equipment and systems are to be functionally tested and proven functional I operational. The RF shall certify and record functional test(s) . The designated DND Representative (i.e. NDQAR, CONO Overseer, Technical SeNices SupeNisor) shall inspect.

Manufacturer's Material Safety and Technical Data Sheets

8. The manufacturer's published Material Safety Data Sheets (MSDS) and Technical Data Sheets (TDS) shall form part of this specification and shall be acquired by the RF. The dry film thickness (OFT) and the minimum I maximum cure times before application of subsequent coat are to be in accordance with the manufacturer's recommendation found in the TDS or by written confirmation from the Field SeNice Representative (FSR). In case of conflict of information, the designated engineering authority (DEA) or FMFCS NACE Inspector shall be consulted. The final resolution I decision on any conflict of information shall be directed, through consultation with the LCMM, DNPS 2-4-4, and I or the FSR, by the FMFCS NACE Inspector.

Materials

9. The RF shall supply all materials sufficient to comply with this specification and any other relevant documentation(s) I specification(s) and provide manufacturer's names, product names, material TDS and material batch numbers. Materials shall not exceed manufacturer's stated shelf life. Refer to Annex C for listing of approved products. The use of any alternate product(s) shall be approved by the coating LCMM, DNPS 2-4-4, through the DEA or FMFCS NACE Inspector.

1 0. All coating material systems shall be supplied from the same manufacturer unless written consent, from the manufacturer, is provided to allow substitute coatings to be used without limitations and voiding warranties. If such consent is not obtainable from the manufacturer, the final resolution I decision shall be directed by the DEA or FMFCS NACE Inspector.

11 . Deliver all materials to the work site in the manufacturer's sealed containers, bearing the manufacturer's labels, identifying product name, material type, colour, batch numbers, etc. Store materials in a dry space away from sources of spark or flame with temperatures ranging as per manufacturer's recommendations. The space shall be kept neat and clean at all times.

Pre-surface Cleaning

12. Clean the overall deck area to remove all loose flaking coatings, salts, grease, dirt, visible

5

R, A!C*

R

H 1-23-003-005/J 1-001 and soluble contaminants in accordance with SSPC-SP-1 Standards, using a biodegradable cleaner/de-glossing agent, Code C415. Immediately after cleaning, thoroughly rinse with fresh water.

a.

b.

The RF shall dispose of all drained liquids in accordance with all applicable municipal, provincial and federal regulations and legislation.

The RF shall provide a Certificate of Disposal.

c. Carry out chloride ion testing in accordance with Para. 12.

Chloride lon Testing

13. Carry out chloride ion testing using semi-quantitative tests in accordance with SSPC-TU-4, Cell Retrieval Methods, Swabbing or Washing Methods, as follows;

a.

b.

c.

on completion of pre-surface preparation to SSPC-SP-1 (Solvent Cleaning), and I or SSPC-SP WJ-4 (Waterjet Cleaning of Metals- Light Cleaning) to ensure the chloride ions are not imbedded into the substrate when cleaning to bare metal; and

on completion of substrate preparation, SSPC-SP-2 (Hand Tool Cleaning), SSPC-SP-3 (Power Tool Cleaning) and SSPC-SP-11 (Power Tool Cleaning to Bare Metal) and I or SSPC-SP WJ-1 (Waterjet Cleaning of Metals- Clean to Bare Substrate), prior to coating application.

the FMFCS NACE Inspector shall witness the tests. Tests are to be recorded, by the RF, in Annex B;

d. The number of tests for each space/deck shall be determined by the amount of surface area being cleaned and treated.

e.

i. For areas less than 10 sq m (1 07 sq ft) a minimum of two (2) tests are required. Any additional requirement is optional at the OAR, DEA or FMFCS NACE Inspector's discretion.

ii . up to 50 sq m (539 sq ft) one (1) test per every 1 0 sq m (1 07 sq ft).

iii. 50 sq m (539 sq ft) to 200 sq m (2153 sq ft) one (1) test per every 20 sq m (215 sq ft).

iv. 200 sq m (2153 sq ft) to 500 sq m (5382 sq ft) one (1) test per 40 sq m (431 sq ft).

v. 500 sq m (5382 sq ft) to 1000 sq m (1 0764 sq ft) one (1 test per 60 sq m (646 sq ft) .

vi. 1 000 sq m (1 0764 sq ft) to 2000 sq m (21528 sq ft) one (1) test per 1 00 sq m (1 076 sq ft).

vii. 2000 sq m (21528 sq ft) to 3000 sq m (32292 sq ft) one (1) test per 150 sq m (1615 sq ft).

viii. 3000 sq m (32292 sq ft) to 4000 sq m (43056 sq ft) one (1) test per 200 sq m (2153 sq ft).

ix. 4000 sq m (43056 sq ft) and up, one (1) test per 250 sq m (2691 sq ft).

The acceptable chloride ion level shall be less than 5 1Jg/cm2 (5ppm). Coatings shall not be removed or applied until this level of cleanliness is achieved; and

6

c

c

R,NC*

R,NC*

R,NC*

R,NC*

NC*

H 1-23-003-005/J 1-001 f. Should chloride ion levels greater then 5 1Jg/cm2 (5ppm) be found, 100% of the areas

shall be re-cleaned as per Para 11 . On completion of re-cleaning , chloride ion testing shall be carried out as per this Para. This evolution shall be carried out until acceptable chloride ion levels of less then 5 1Jg/cm2 (5ppm) is achieved. Re-cleaning of less then 100% of the total surface area shall be at the discretion of the DEA or FMFCS NACE Inspector.

NOTE: Should chloride ion levels greater then 5 1-1g/cm2 (5ppm) be found, the RF, the designated DND Representative (i.e. NDQAR, CONO Overseer, Technical Services Supervisor) and I or ship's staff shall investigate to find if a source of contamination is present. If a source of contamination is found , it shall be remediated prior to proceeding with pre-surface preparation and I or surface preparation and I or coating application.

Surface Preparation -Steel Substrate

14. Listed below are three (3) methods of cleaning steel substrates to bare metal. The method of cleaning the substrate to bare metal shall be determined by the FMFCS/ENG/NAO/Hull Surveyor at time of survey and shall be recorded/specified in the Hull Survey report or any other relevant documentation(s) I specification(s) in witch this Jt has been attached.

Method 1: Cleaning to bare metal lAW SSPC-SP-5 (White Metal Blast Cleaning) Standards;

Blast clean 100% of the steel deck areas, complete with appendages as required , to bare metal in accordance with SSPC-SP-5 Standards to achieve a 62.5 to 75 microns (IJm) angular surface profile and a final surface condition as depicted in SSPC Visual Standard SSPC-VIS 1-89, C SP 5.

NOTES:

(1) Steel shot shall not be used alone. If steel shot is used, the abrasive mixture shall consist of a mix of at least 20% steel grit and the balance steel shot of sufficient size to NC* achieve a 62.5 to 75 microns (l-Im) angular surface profile.

(2) Areas that cannot be abrasive blast cleaned shall be cleaned by hand and power tools in accordance with SSPC-SP-11 Standards to achieve a final surface condition as NC* depicted in SSPC-VIS 3, E SP 11 . The cleaned surface shall be free of all visible oil , grease, dirt, dust, mill scale, rust, coating, oxides, corrosion products, and other foreign matter. Slight residues of rust and I or paint may be left in the lower portions of existing pits. The surface shall be roughened to produce a surface profile of no less than 38.1 IJm.

(3) The total allowable areas of the deck required to be cleaned to SSPC-SP-11 NC* Standards shall be less then 5%.

(4) All exposed appendages and projecting surfaces shall be abrasive blast cleaned to bare metal up to a height of 150mm (6 inches) above deck (i.e. bulkheads, ship sides, house sides, bulwarks, seatings, foundations, boundary bars, deck fittings, portable deck cover plates, coamings, etc.) and

(5) Edges of intact coatings bordering areas cleaned to bare metal shall be feathered back NC* a minimum of 50mm (2 inches) to produce a smooth final transition I finish when recoated.

Method 2: Cleaning to bare metal lAW SSPC-SP-11 (Power Tool Cleaning to Bare Metal) Standards;

Clean 1 00% of the steel deck areas, complete with appendages as required, to bare metal in accordance with SSPC-SP-11 Standards to achieve a final surface condition as depicted in SSPC-VIS 3, E SP 11. The cleaned surface shall be free of all visible oil , grease, dirt, dust, NC* mill scale, rust, coating , oxides, corrosion products, and other foreign matter. Slight residues

7

HI-23-003-005/JI-001 of rust and I or paint may be left in the lower portions of existing pits. The surface shall be roughened to produce a surface profile of no less than 38.1 IJm.

NOTES: .

(1) Any areas of exposed steel substrate exhibiting ferrous oxide {black) shall be re-cleaned to SP-11 Standards by means of needle gunning and I or rotary scaler I NC* scarifier to remove the ferrous oxide and to achieve a final surface condition as depicted in SSPC-VIS 3, E SP 11.

(2) Any areas of exposed steel substrate exhibiting any degree of polishing and I or burnishing shall be re-cleaned to SP-11 Standards to achieve a final surface condition NC* as depicted in SSPC-VIS 3, E SP 11.

(3) All exposed appendages and projecting surfaces shall be power tool cleaned to bare metal up to a height of 1 OOmm (4 inches) above deck (i.e. bulkheads, ship sides, house sides, bulwarks, seatings, foundations, boundary bars, deck fittings, portable deck cover plates, coamings, etc.) and

(4) Edges of intact coatings bordering areas cleaned to bare metal shall be feathered back a minimum of 50mm (2 inches) to produce a smooth final transition I finish when NC* recoated .

Method 3: Cleaning to bare metal lAW SSPC-SP WJ-1 Standards (Waterjet Cleaning of Metals - Clean to Bare Substrate);

Clean 100% of the steel deck areas complete with appendages as required, to bare metal in accordance with SSPC-SP WJ -1 Standards to achieve a final surface condition as depicted in SSPC-VIS 4.

NOTES:

(1) When waterjet cleaning in accordance with SSPC-SP WJ-1 Standards, the RF must be aware of and ensure that all environmental policies are upheld, such as the C recovery of all effluents.

(2) The water used for waterjet cleaning shall be pure so it does not contaminate the surface being cleaned.

(3) Waterjet cleaning does not produce an etch or angular surface profile, rather it exposes the original abrasive-blasted or corroded surface profile. After waterjet NC* cleaning, should any area of the prepared surface not meet a minimum angular surface profile of 38.1 IJm, the RF will be responsible to achieve the specified profile as part of the original contract.

(4) Any areas of exposed steel substrate exhibiting ferrous oxide {black) shall be cleaned to SSPC-SP-11 Standards by means of needle gunning and/or rotary scaler/scarifier to NC* remove the ferrous oxide and to achieve a final surface condition as depicted in SSPC-VIS 3, ESP 11.

(5) Any areas of exposed steel substrate exhibiting any degree of polishing and/or burnishing shall be cleaned to SSPC-SP-11 Standards to achieve a final surface NC* condition as depicted in SSPC-VIS 3, E SP 11.

(6) All waterjet cleaning shall be to a WJ-1 Standard and shall meet flash rust conditions of "no flash rust" to "light flash rust" as described in SSPC-SP WJ-1/NACE WJ-1 NC* Standards prior to coating application.

(7) All exposed appendages and projecting surfaces shall be waterjet cleaned to SSPCSP WJ-1 I NACE WJ-1 Standard up to a height of 100mm (4 inches) above deck (i.e.

8

H 1-23-003-005/ J 1-001 bulkheads, ship sides, house sides, bulwarks, seatings, foundations, boundary bars, deck fittings, portable deck cover plates, coamings, etc.) and

(8) Edges of intact coatings bordering areas cleaned to bare metal shall be feathered back a minimum of 50mm (2 inches) to produce a smooth final transition I finish when NC* recoated.

Surface Preparation -Aluminum Substrate

15. Listed below are three (3) methods of cleaning aluminum substrates to bare metal. The method of cleaning the substrate to bare metal shall be determined by the FMFCS/ENG/NAO/Hull Surveyor at time of survey and shall be recorded I specified in the Hull Survey report or any other relevant documentation(s) I specification(s) in witch this Jl has been attached.

Method 1: Cleaning to bare metal to an extent similar to lAW SSPC-SP-5 (White Metal Blast Cleaning) Standard;

Blast clean 1 00% of the aluminum deck areas and associated appendages to bare metal, to achieve an angular surface profile of between 38.1 to 50 IJm. The surface shall be free of all visible oil , grease, dirt, dust, paint, oxides, corrosion products, and other foreign matter.

NOTES:

(1) The grit used for blasting aluminum shall be Grade 2 (Fine) or Grade 3 (Extra Fine) .

(2) Copper based grit shall not be used.

(3) Appendages I projecting surfaces - all exposed appendages and projecting surfaces shall be abrasive blast cleaned to bare metal blast up to a height of 1 OOmm (4 inches) above deck (i.e. bulkheads, ship sides, house sides, bulwarks, seatings, foundations, boundary bars, deck fittings, portable deck cover plates, coamings, etc) .

(4) Areas that cannot be abrasive blast cleaned shall be power tool cleaned using 3M non-woven abrasive pads (or equivalent) to achieve a surface, when viewed without NC* magnification, that is free of all visible corrosion products and other foreign matter. The surface shall be roughened to produce a surface profile of no less than 38.1 IJm.

(5) Edges of intact coatings bordering areas cleaned to bare metal shall be feathered back a minimum of 50mm (2 inches) to produce a smooth final transition I finish when recoated. NC*

(6) The FMFCS NACE Inspector shall be present at the beginning and/or during blasting of aluminum to examine depth of profile, embedding of grit in the substrate, consistency of white metal finish , degree of warpage, etc. Any defects I problems arising from the NC* examination shall be corrected prior to the continuation of the blast cleaning process. The periodicity 1 frequency of blasting inspections, of aluminum substrate, are at the discretion of the FMFCS NACE Inspector. Should any problems and I or concerns arise during the blasting process, the RF is to contact the designated DND Representative (i.e. NDQAR, CONO Overseer, Technical Services Supervisor) and I or the FMFCS NACE Inspector for inspection.

Method 2: Cleaning to bare metal lAW SSPC-SP-11 (Power Tool Cleaning to Bare Metal) Standards;

Clean 100% of the aluminum deck areas and associated appendages to bare metal in accordance with SSPC-SP-11 Standards using 3M non-woven abrasive pads (or equivalent) to achieve a surface, when viewed without magnification, that is free of all visible corrosion products and other foreign matter.

9

HI-23-003-00SIJ 1-001 Notes:

(1) The surface shall be.roughened to produce a surface profile of no less than 38.1 IJm. NC*

(2) Appendages I projecting surfaces- all exposed appendages and projecting surfaces shall be cleaned to bare metal to a height of 1 OOmm (4 inches) above deck (i.e. bulkheads, ship sides, house sides, bulwarks, seatings, foundations, boundary bars, deck fittings, portable deck cover plates, coamings, etc).

(3) Edges of intact coatings bordering areas cleaned to bare metal shall be feathered back a minimum of 50mm (2 inches) to produce a smooth final transition I finish when recoated.

Method 3: Cleaning to bare metal lAW SSPC-SP WJ-1 Standards {Waterjet Cleaning of Metals- Clean to Bare Substrate);

Clean 100% of the aluminum deck areas complete with appendages as required, to bare metal in accordance with SSPC-SP WJ-1 to achieve a final surface condition as depicted in SSPC-VIS 4.

NOTES:

(1) When waterjet cleaning in accordance with SSPC-SP WJ-1 Standards, the RF must

NC*

be aware of and ensure that all environmental policies are upheld, such as the C recovery of all effluents.


(3) Waterjet cleaning does not produce an etch or angular surface profile, rather it exposes the original abrasive-blasted or corroded surface profile. After waterjet NC* cleaning, should any area of the prepared surface not meet a minimum angular surface profile of 38.1 iJm, the RF will be responsible to achieve the specified profile as part of the original contract.

(4) All exposed appendages and projecting surfaces shall be waterjet cleaned to bare metal up to a height of 1 OOmm (4 inches) above deck (i.e. bulkheads, ship sides, house sides, bulwarks, seatings, foundations, boundary bars, deck fittings, portable deck cover plates, coamings, etc) and;

(5) Edges of intact coatings bordering areas cleaned to bare metal shall be feathered back a minimum of 50mm (2 inches) to produce a smooth final transition I finish when NC* recoated.

Surface Preparation Inspections

16. The RF shall carry out the following inspections on completion of surface preparation. If oxidation occurs between cleaning to bare metal and coating application, the surface shall be re-cleaned to bare metal to the specified standard. Any areas subject to contamination after cleaning to bare metal shall be cleaned I degreased in accordance with SSPC-SP-1 Standard. The RF shall certify and record inspections and verify the surface has been prepared in accordance with this specification. The FMFCS NACE Inspector shall witness each inspection point.

a. Visual Inspection- surface preparation verified in accordance with SSPC-VIS 1-89, SSPC-VIS 2, SSPC-VIS 3, SSPC-VIS 4, or SSPC-VIS 5.

b. Visual Cleanliness Inspection - surface on final inspection is to be free of dust and visible contamination. Verify cleanliness by placing a clear adhesive tape, pressed on the surface at several locations that is representative of the entire area, and remove.

10

R, NC*

HI-23-003-005/JI-001 When viewed, the removed tape shall be free from any visible dust, dirt, and other

C.

d.

contaminants.

NOTE: For steel decks prepared to SSPC-SP WJ-1 Standards; all areas shall meet flash rust conditions of "no flash rust" to "light flash rust" as described in SSPC-SP WJ-1 Standards. All areas not meeting the required Standard prior to coating application shall be re-cleaned until the required Standard is met.

Non-visual Cleanliness Inspection- carry out chloride ion testing in accordance with Para. 12 of this specification and record in Annex B.

Surface Profile Measurements - measure and record surface profiles in accordance with NACE RP0287-95 and the RF shall record in Annex A.

Structural Inspection

17. On completion of cleaning the deck to bare metal lAW SSPC-SP-2 I 3 I 5 I 11 and I or WJ-1 Standards, and prior to any coating application, sufficient time shall be allotted for a DEA or FMFCS/ENG/NAO/Hull Surveyor to carry out a structural survey of all exposed substrate. Any damage I wastage found, not within acceptable Standards, arising from the structural survey will be raised as item(s) of additional work. Should any damage I wastage be found, the DEA or FMFCS/ENG/NAO/Hull Surveyor will forward a det3iled description of findings to the DND Representative (i.e. NDQAR, CONO Overseer, Technical Services Supervisor) and the Ship's Senior Hull Technician.

Treatment- Steel and Aluminum Substrate

Pre-coating Application Inspections

18. The RF shall ensure that surface preparation is as specified in Para. 14 and/or 15 of this specification. Environmental conditions in accordance with the following or as recommended by the coating manufacturer are not to be exceeded during the coating application process. The FMFCS NACE Inspector shall witness each inspection point:

a. ambient temperature not less than r C;

b. surface temperature 3° C above dew point and not to exceed 49° C; and

NOTE: International products lntershield 300, lntershield 6GV, and lntercryl 588 have a maximum temperature of 60°C for application purposes.

c. relative humidity (RH) below 85%.

NOTE: Ambient temperature, surface temperature, dew point, and RH shall be recorded by

R, NC*

R,NC*

R, NC*

NC*

R, NC*

the RF prior to the start of each coating application and as required thereafter to R verify that specified parameters are within specification and I or at the discretion of the FMFCS NACE Inspector.

Treatment - Steel and Aluminum Substrate Primer System

19. a. Areas of steel decks that can not be cleaned to SSPC-SP- 11 or WJ-1 Standards shall be cleaned to SSPC-SP-2 or 3 to the fullest extent possible and coated with one (1) coat of Two-component Epoxy Rust Penetrating Primer I Sealer, Code C406, to a OFT as per manufacturer's instructions, prior to application of 151 coat of epoxy primer, Code C420.

b. A stripe coat shall be applied to all edges, deck fittings , coamings, seatings, weld seams, etc, previously cleaned to bare metal, using an epoxy primer, Code C420. Stripe coating shall encompass all edges as well as at least a 25mm (1 inch) border

11

R, NC*

H 1-23-003-005/JI-001 outside each edge. T-he stripe coat shall be neat in appearance and free from runs, sags or curtains. The stripe coat shall be allowed to dry, at least set to touch, before the full first coat is applied.

c. Apply one (1) or more coats as required, using alternating colours, of an epoxy primer, Code C420, once the stripe coat has been allowed to dry, at least set to touch, to the overall prepared surface, to a minimum OFT of 150 ~m .

d. Within the recommended re-coat period, apply one (1) coat of an epoxy primer, Code C420, using alternating colours, to the overall primed I prepared surface, to a minimum OFT of 125 ~m to 150 ~m .

e. The final OFT for the primer system shall be between 250 ~m to 300 ~m . Any areas not conforming to the minimum OFT requirement shall be re-coated, within the recommended re-coat period, using alternating colours. The minimum OFT requirement shall be achieved prior to application of any subsequent coating system.

NOTES:

(1) There shall be no application of epoxy primer, Code C420 on existing I remaining non-slip and I or non-traffic coating. If application of epoxy primer, Code C420 occurs on existing I remaining non-slip and/or non-traffic coating, it shall be immediately removed prior to curing.

(2) Mixing of coatings is only allowable with the permission of the FMFCS NACE Inspector, and shall be done lAW manufacturer's instructions I mix ratio and shall be appropriately mixed I measured using suitable graduated mixing sticks and I or containers.

Steel and Aluminum Substrate Non-slip, Traffic Areas

20. a.

b.

a.

Apply to primed traffic areas a non-slip, epoxy deck coating, Code C419, colour US Fed-Std-595B #36076, flat dark grey. Actual coverage rate shall be in accordance with manufacturer's :;pecification.

With the material freshly stirred, in accordance with manufacturer's specifications I recommendations to evenly disperse aggregate, pour substantial portion of mixture onto the deck in a band approximately 450mm to 600mm (18 to 24 inches) wide. Using a smooth phenolic core roller, spread the non-skid coating evenly by pulling the puddle towards the applicator that is one (1) direction only. Avoid back and forth roller motion. With puddle nearly rolled out, pour additional mixed material over remaining puddle and continue application as above.

The final finished surface shall present a uniform rough appearance over the entire surface. No loosely bound clumps of particles shall be present. The surface profile shall show a pattern of hard raised peaks, 1.5 - 2.4mm (1 /16 to 3/32 inch) high and 12.5- 25mm (%to 1 inch) apart. The dry non-skid coating at its thinnest point shall be at least 750 ~m .

NOTE:

1. A sample panel depicting the textured finish of the non-skid coating that must be achieved is available for viewing through the FMFCS/NAO/Hull Surveyors.

Steel and Aluminum Painted Non-Traffic Areas

21 . a. Apply one (1) or more coats, as requ ired, of an epoxy tie-coat, Code C426, over the already applied epoxy primer, Code C420, within the manufacturer's recommended recoat time, to achieve a minimum OFT of 50 to 100 ~m. followed by;

12

NC*

NC*

NC*

R,NC*

H 1-23-003-005/JI-001

b. two (2) coats of Exterior Alkyd Marine Enamel Topcoat, Code C061 to all primed deck non-traffic I Dado areas, complete with appendages I projecting surfaces 1 OOmm (4 inches) above the deck, to DFT of 40 to 60 1-1m per coat, within the manufacturer's recommended re-coat time. The colours shall be in accordance with existing colour scheme and US Federal Standard 5958, colours Grey 16076 and Black 17038:

c. Appendages I Projecting Surfaces above the non-traffic/Dado areas: Apply, two (2) coats of Enamel , Silicone Alkyd Copolymer (LSA) Topcoat, Code C411 to bulkheads, ship sides, house sides, bulwarks and surfaces projecting above the

Markings

1 OOmm (4 inches) non-traffic/Dado areas, in accordance with the existing colour scheme.

22. Apply warning and control markings in accordance with the applicable drawing or in accordance with the existing arrangement if no drawing is available. Locations of Warning and control markings shall be noted and recorded , by the RF, for reference prior to coating removal.

a. apply markings on non-slip, traffic areas, using two (2) coats of Code C177, polyurethane two-component topcoat. DFT to be in accordance with manufacturer's specifications. To prevent markings in traffic areas from becoming slippery, the second coat shall have one {1) part aggregate (glass beads) mixed to five (5) parts paint. Colours shall be in accordance with US Fed-Std-5958: Yellow- 33538; White-37925; Red - 11350, and Black - 17038.

b. apply markings on non-traffic areas, using two (2) coats of Code C061 , Exterior Alkyd Marine Enamel Topcoat. DFT to be in accordance with manufacturer's specifications. Colours shall be in accordance with US Fed-Std-595B: Yellow- 33538; White-37925; Red - 11350, and Black - 17038.

Coating Inspections Post Applications- OFT Measurements

23. The RF shall carry out DFT measurements in accordance with SSPC-PA-2 and shall record their readings in Annex A. The FMFCS NACE Inspector shall witness each inspection I test.

a. DFT measurements of each coating application shall be taken on completion of curing time as per manufacturer's recommendations and/or prior to the next coating application.

b. The DFT measurements for each coating system shall not fall outside the specified parameters. Should the DFT measurements, for each coating system, fall outside the specified parameters, the areas not meeting the minimum DFT requirements shall be remediated I recoated and the required DFT measurements shall be achieved prior to application of a subsequent coating system.

c. DFT measurements shall be taken after final coating application, on completion of curing time as per manufacturer's recommendations. Areas not having sufficient build of coating shall be re-coated until the required final DFT is achieved.

Vertical Launch System (VLS) Launcher Top -IRQ Class

24. THE VLS LAUNCHER TOP SHALL NOT BE PREPARED AND RECOATED UNDER THIS SPECIFICATION. UNDER NO CIRCUMSTANCES SHALL THE RF ATTEMPT ANY REPAIR OF THE VLS LAUNCHER TOP.

Preparation and Coating Requirements

25. Select all equipment used for surface preparation and coating application to be effective and

13

R, AC*

R,NC*

H 1-23-003-00SIJI-001 economical to produce the required surface fin ish. Selected equipment is to be properly maintained in good working order and only operated by trained personnel.

26. Operate equipment with clean compressed air, free from oil and moisture. Compressed air R supply shall be fitted with oil and moisture traps with adequate capacity to produce the desired air pressure and volume. Verify cleanliness of the air supply at the beginning of each shift by conducting a blotter test in accordance with ASTM D-4285- Indicating Oil and Water in Compressed Air.

27. Maintain surface preparation and coating conditions in accordance with Para. 15 and Para. 17 of this specification.

28. Before placing the deck area back into service, allow sufficient curing time for the final coating system, as per the coating manufacturer's recommendation found on the technical data sheet. The work area is to be well ventilated, with controlled ambient conditions during the curing process.

29. Clean, inhibit, prime and paint new and disturbed work in accordance with appropriate part I section of the latest edition of D-23-003-005ISF-002 (Maintenance Painting of HMC Ships) and manufacturer's instructions. Any conflict between the maintenance painting manual, the manufacturer's instructions and/or this specification shall be brought to the attention of the DEA and I or the FMFCS NACE Inspector for clarification and I or resolution. The final resolution I decision on any conflict of information shall be directed, through consultation with the LCMM and I or the FSR, by the DEA or FMFCS NACE Inspector.

Inspections

30. The RF shall have a NACE CIP Level l I Coating Inspector on staff to conduct self-inspections and supply the required documentation to the DND Representative (i.e. NDQAR, CONO Overseer, Technical Services Supervisor) IDEA I FMFCS NACE Inspector upon request.

a. Inspection hold points are indicated in the right hand column throughout the specification. The RF- shall advise the designated DND Representative I DEA I and I or FMFCS NACE Inspector in sufficient time to be present for the inspection.

b. When the symbol "NC" or "NC*" appears in the right hand margin of a specification, it indicates a stage in the work, as specified in the Description of Work Required , that the designated DND Representative (i.e. NDQAR, CONO Overseer, Technical Services Supervisor) shall be advised by the RF in sufficient time to have a designated DND Representative IDEA I and I or FMFCS NACE Inspector as specified, present during the RF's inspection I examination. The RF retains the sole responsibility for conducting the inspection I examination and for producing the required objective evidence required by the Description of Work.

NOTE: Should the RF proceed with further work as described in the specification without advising the designated DND Representative I DEA I and I or FMFCS NACE Inspector in sufficient time to be present, the RF shall be required to re-open the equipment I system and I or re-clean the deck to bare metal for the required inspection I examination 1 validation by the designated DND Representative without cost nor prejudice to the Crown.

c. "A/C" point- The attendance of a designated DND Representative IDEA 1 and 1 or FMFCS NACE Inspector during the RF's inspection I examination is annotated as an "NC" point and is at the discretion of the designated DND Representative 1 DEA 1 and 1 or FMFCS NACE Inspector.

d. "A/C*" point- The attendance of a designated DND Representative IDEA 1 and 1 or FMFCS NACE Inspector during the RF's inspection I examination is annotated as an "NC*" point and is deemed critical , therefore, the designated DND Representative 1 DEA I and I or FMFCS NACE Inspector shall be in attendance.

14

H 1-23-003-005/J 1-001

e. Defects/Reading Points -When the symboi"D" (defects) or "R" (readings) appear in the right hand margin of a specification it indicates a stage in the work as specified in the Description of Work Required, that the RF shall record, in writing, the data required in the Description of Work. Unless a format is specified in the appropriate Description of Work Required, the RF shall provide its own format(s) for reporting readings and defects. Format(s) used by the RF shall be suitable for accurate photocopying when completed. The RF shall forward the recorded data immediately to the FMFCS NACE Inspector unless otherwise specified.

f . Inspection equipment shall be held and used by the RF for tests performed. All measuring/recording equipment shall be calibrated in accordance with the manufacturer's recommended practice, recorded and records delivered to the FMFCS NACE Inspector upon request.

g. Environmental Certificates of Disposal Required -When the symbol "C" appears in the right hand margin of a specification, it indicates that a signed Environmental Certificate of Disposal is required for the work as specified in the Description of Work Required. This certificate shall confirm to Canada that the environmentally hazardous substance is lawfully disposed of in accordance with all applicable Municipal, Provincial and Federal regulations and legislation.

Inspection Equipment

31 . The following inspection equipment and standards are to be held and used by the contractor for tests performed:

a. surface thermometers;

b. air thermometers;

c. sling psychrometer and I or digital environmental gauge;

d. replica tape and micrometer and I or digital surface profile gauge;

e. dry film coating thickness gage;

f. wet film coating thickness gage;

g. standards, in accordance with page 2, Related Documents; and

h. chloride ion test kits.

Workmanship

32. a. All work shall be free from runs, sags, curtains, holidays or other visible defects, such as blisters, resulting from solvent entrapment.

b. There shall be no uncoated areas. Areas not having sufficient build of coating shall be re-coated until the required final DFT is achieved;

c. There shall be no loosely bound clumps of non-skid particles;

d. Edges of intact coatings bordering areas cleaned to bare metal shall be feathered back a minimum of 50mm (2 inches) to produce a smooth final transition I finish when A/C* recoated .

e. The intersection of traffic and non-traffic areas shall be s!raight and neat in appearance;

15

H 1-23-003-005/JI-001

Safety

f. All personnel entering the work area shall wear coveralls, clean boots and gloves to minimize contamination of the surfaces. The entrances to the work area shall have an area to wipe soles of boots clean ; and

g. On completion of all work, the work site shall be free from work related debris or unused materials. Particular care is to be taken to ensure all scattered debris, paint chips are removed from recesses, sockets, deck fittings, ventilation inlets, etc.

33. Attention is drawn to the highly inflammable nature of the specified coatings and their solvents. Care must be exercised to ensure adequate ventilation is provided to prevent against toxic hazards and explosive concentrations of vapors and that sources of ignition are eliminated from areas where such concentrations could occur.

34. The RF shall comply with the requirements of all MSDS and all safety regulations in accordance with applicable federal and provincial regulations. The following acts and regulations apply:

a. Occupational Safety and Health, Part 11 , Canada Labour Code;

b. Occupational Safety and Health, Policy Volume of the TB Manual;

c. DND Safety Legislation and Policy, C-02-040-009/AG-000; and

d. DND Safety Policy and Programs, A-GG-040-001/AG-001.

35. The RF shall comply with all safety requirements in accordance with applicable federal , provincial and municipal regulations and legislation.

Environmental Regulations and Requirements

36. The RF shall remove, handle, store, transport and dispose of all hazardous waste in accordance with all applicable federal, provincial and municipal regulations and legislation. Precautions shall be taken during cleaning and painting, to protect the ship's equipment and the environment from contamination. The RF shall take precautions during coating removal operations as coatings may contain heavy metals, such as lead and chromates. The RF shall subject solid waste, i.e. used blast media, to leachate testing to determine appropriate disposal option. The RF shall provide a Disposal Certificate if the waste material from the cleaning operation is classed as hazardous waste.

a. the RF shall comply with the following acts:

(1) the Canadian Environmental Protection Act; and

(2) the Canadian Fishery Act.

Environmental Aspects

37. The following environmental aspects have been identified for the above work specification. This list shall not be considered to be all inclusive and does not remove the responsibility of the RF to identify all the environmental aspects related to this work specification:

a. Air Emissions: power wash cleaning, abrasive blasting, power tool cleaning, coating application;

b. Hazardous Materials: degreasers, solvents, epoxy primers, polyurethane, epoxy nonskid coating ;

16

c

H 1-23-003-005/J 1-001 c. Hazardous Waste: cleaning waste, spent abrasive grit, paint chips, paint waste;

d. Noise emissions: power wash cleaning, abrasive blasting, power tool cleaning, coating application;

e. Non-hazardous solid waste: paint waste;

f. Process Water: high pressure wash, degreaser; and

g. Spills I Releases: degreaser, paint and solvents.

Deliverables

38. The RF shall forward the following deliverables to the designated DND Representative (i.e. NDQAR,CONO Overseer, Technical Services Supervisor) within five (5) working days of work completion:

a. Disposal Certificates;

b. Preparation and Coating Appl ication Recording form, Annex A; and

c. Chloride Ions Testing Recording form , Annex B.

17

c

SSPC-SP-12

SSPC-SP-1

SSPC-SP-2

SSPC-SP-3

SSPC-SP-11

SSPC-SP-5

SSPC-SP-10

SSPC-SP-7

BATCH NO.

COLOUR NO.

D

SURFACE TEMP

AMBIENT TEMP

RELATIVE HUMIDITY

DEW POINT

MIN

MAX

WET BULB TEMP

DFT SPECIFIED

DFT ACHIEVED

INITIALS

DATE

RF'S NAME (PRINTED):

H 1-23-003-005/JI-001 ANNEXA


DATE: RF'S SIGNATURE:

DATE: RF'S SIGNATURE:

A-1

H 1-23-003-005/J 1-001 ANNEX B

CHLORIDE ION TESTING RECORDtNG FORM

SHIP'S NAME:

Reason for Testing:

AFTER CLEANING TO AFTER CLEANING TO SSPC-SP-2/3/5/11 AND/OR

COMPARTMENT AREA TESTED SSPC-SP-1 AND/OR 12 12-WJ-1 (in 1Jg/cm2

) (Prior to Coating) (in ua/cm2l

..

RF'S NAME: I RF'S SIGNATURE: DATE:

B-1

HI-23-003-005/JI-001

ANNEXC

NAVAL SPECIFICATION MATERIAL LIST

SHIP/CLASS: DATE:

Jl NO: HI-23-003-003/JI-001 Jl AMENDMENT:

(1) (2) (3) (4) (5) (6) (7) (8) (9) Line Dwg Number Stock Number Description/Part No. Qty Unit GSM CFM Remarks Item 1001 Code C406, Two-Component As f{eq 'd X

Epoxy Rust Penetrating Primer/Sealer

1002 Code C420, Epoxy Primer for As Req'd X Epoxy Non-skid

1003 Code C177, Polyurethane Two- As Req'd X Component

1004 Code C419, Epoxy Non-skid As Req'd X

1005 Code C061, Enamel, Alkyd, As Req'd X Marine, Exterior, Gloss ·

1006 Code C426, Epoxy Tie Coat As Req'd X

1007 Code C415, Biodegradable As Req'd X Cleaner, De-glossing Agent

1008 Code C411, Enamel, Silicone As Req'd X Alkyd Copolymer (Low Solar Absorption Pigmentation and Antistain Properties)

C-1

CPF- hangar door panel repairs approx 19 mm -------- ------ - ---- --- ¥

...,J; ~ -~

- _- . - -1 - .

two panels make up one full panel bolted together with gasket & welded to the end bars lAW existing arrangement & reference sketches CFTO

/

,; , . . I -- ] --

.__ ~12ical view of interior side of hangar door 12anel

~

reuse existing rollers (showing location of re12air to one 12anel) bottom of panel reuse existing rollers

3/4" x 2" steel flat bar at each ens

butt joint tv12ical view of exterior side of hangar door 12anel (showing location of re12air to one 12anel)

fill gap with weld metal

0'-3" 1..: )lol

~ .....

approx 19 mm thick flat bar

0'-3" 1..: )lol

end 12re12aration of 12anels to be joined butt joirit

ty12ical detail view 1a12 joint of 12anel sections r.---__ ---__ -----1 interface of lap joint

~I

NTS

~ end -·--·

end view

~ end view section AA

Ji.. Fleet Maintenance • Facility Cape Scott

H 1-23-003-005/J 1-003 Amended 31 OCTOBER 2013

STANDARD FMF CAPE SCOTT JOB INSTRUCTION SURFACE PREPARATION AND COATING APPLICATION PROCEDURE

APPLICABLE TO ALL CLASS SHIPS

COATING REPAIRS AND TOPCOAT OVERALL FOR

NON-SLIP AND PAINTED DECKS

LOCATION VARIOUS

(Supersedes Dated 06 March 2012)

Approved By: NAO/SNR HS

Originator: NAO/HULL SURVEY Contact: NAO/HULL SURVEY Phone: 427-3885

NEI NUMBER:

PURPOSE:

E-28-418-000 (HFX CLASS) E-28-175-000 (I RO CLASS) E-28-672-BOO (PTR CLASS

This specification states the requirements for the surface preparation and coating application for repairing non-slip deck coating and application of a topcoat overall.

RELATED DOCUMENTS:

D-23-003-005/SF-002

C-39-003-00 1 I AG-001

C-70-328-000/M P-00 1

SSPC-SP-1

SSPC-SP-11

SSPC-SP WJ-1 /NACE WJ -1




SSPC-VIS-3 SSPC-VIS-4

SSPC-PA-2

SSPC-TU-4

NACE RPO 287-95

ASTM D-4285

SSPC PAINTING MANUAL

DWG 0251110

DWG HFX-D28-396-000-01 , SHTS 7, 8, AND 9 DWG 0151097

C-02-040-009/ AG-000

A-GG-040-001 /AG-001

SPECIFICATION FOR MAINTENANCE PAINTING OF HMC SHIPS

HELICOPTER/SHIP INTERFACE DESIGN GUIDANCE AND CLEARANCE CRITERIA MANUAL THIRD LINE MAINTENANCE INSTRUCTION FOR VERTICAL LAUNCH SYSTEM- LAUNCHER TOP RESURFACING SOLVENT CLEANING

POWER TOOL CLEANING TO BARE METAL

JOINT SURFACE PREPARATION STANDARD WATERJET CLEANING OF METALS - CLEAN TO BARE SUBSTRATE (WJ-1) JOINT SURFACE PREPARATION STANDARD WATERJET CLEANING OF METALS- VERY THOROUGH CLEANING (WJ-2) JOINT SURFACE PREPARATION STANDARD WATERJET CLEANING OF METALS -THOROUGH CLEANING (WJ-3) JOINT SURFACE PREPARATION STANDARD WATERJET CLEANING OF METALS- LIGHT CLEANING (WJ-4) VISUAL STANDARD FOR POWER AND HAND TOOL CLEANED STEEL GUIDE AND REFERENCE PHOTOGRAPHS FOR STEEL SURFACES PREPARED BY WATERJETIING MEASUREMENT OF DRY COATING THICKNESS

FIELD METHODS FOR RETRIEVAL AND ANALYSIS OF SOLUBLE SALTS ON SUBSTRATE NACE STANDARDS, FIELD MEASUREMENT OF SURFACE PROFILE OF ABRASIVE BLAST CLEANED STEEL SURFACES INDICATING OIL AND WATER IN COMPRESSED AIR

VOLUME 2, 2005 EDITION

FLIGHT DECK MARKINGS IRQ CLASS

PAINTING AND PRESERVATION SCH, (MARKINGS) HFX CLASS

FLIGHT DECK AND HANGAR MARKINGS, PTR CLASS

DND SAFETY LEGISLATION AND POLICY

DND SAFETY POLICY AND PROGRAMS

OCCUPATIONAL SAFETY AND HEALTH PART 11, CANADA LABOUR CODE

OCCUPATIONAL SAFETY AND HEALTH, POLICY VOLUME OF THE TB MANUAL

THE CANADIAN ENVIRONMENTAL PROTECTION ACT

THE CANADIAN FISHERY ACT

ANNEX(ES):

ANNEX A

ANNEX B

ANNEXC



NAVAL SPECIFICATION MATERIAL LIST (NSML)

2

H 1-23-003-005/J 1-003

DESCRIPTION OF WORK

The Repair Facility (RF) shall carry out the following work:

Scope

1 . The intent of this specification is to provide instructions for the surface preparation and the coating applications for a partial repair and full top-coat of a non-slip and/or painted deck coating system on interior/exterior steel and aluminum decks.

2. The work involves the following:

(1) cleaning the entire specified area to remove all loose flaking coatings, salts, grease, dirt, visible and soluble contaminants and cleaning required damaged and I or deteriorated areas to bare metal lAW SSPC-SP-11 Standards;

(2) applying an Epoxy Primer System to bare metal areas;

(3) applying a Type 1, Comp G, LSA Epoxy Non-slip Deck Coating (traffic areas) and a one (1) coat of Polyurethane or Exterior Alkyd Marine Enamel (non-traffic areas) over the Epoxy Primer System; followed by

(4) the application of a Low Solar Absorbant waterborne non-skid deck finish over existing and repaired areas of Non-slip Deck Coating (traffic areas) and the application of a Polyurethane or Exterior Alkyd Marine Enamel Topcoat over existing and repaired areas of non-traffic.

NOTES:

(1) The work specified in this Job Instruction shall not be considered to be the only requirement for the coating repairs. Any additional coating repairs/work required in addition to this Job Instruction shall be as specified in the Hull Survey report or any other relevant documentation(s) I specification(s) in which this Jl has been attached.

(2) The RF shall have a NACE CIP Level II Coating Inspector on staff to carry out all coating inspections and record all applicable data as detailed within the specification .

(3) A FMFCS/ENG/NAO/Hull Surveyor NACE CIP Level II Coating Inspector (also referred as FMFCS NACE Inspector) may witness inspections as detailed within the specification. The frequency and level of involvement of the FMFCS NACE Inspector will be left to the discretion of the FMFCS NACE Inspector.

Precautions

2. Take precautions during the pre-surface preparation , surface preparation, pre-treatment and painting period to contain all cleaning material, waste water and debris as not to contaminate the ship's interior compartments and the atmosphere where equipment is stationed. Provide temporary protection to contain wasted water and to prevent damage and I or over-spray to ship's structure, equipment and fittings as required.

a. temporarily cover and seal furnishings, electrical and electronic equipment. Close ventilation inlets and outlets, doors, windows and hatch openings. Temporarily blank or plug drain openings and pre-wet nozzles during cleaning and painting to prevent the ingress of water, dust, dirt, grit, paint fumes, etc.

b. take precautions during coating removal operations as coating may contain heavy metals such as lead and chromates. Leachate test solid waste, (i.e. the paint chips), to determine appropriate disposal option. Disposal of all hazardous waste in accordance with all applicable municipal, provincial and federal regulations and

3

REMARKS

c

H 1-23-003-005/J 1-003 legislation. A Disposal Certificate shall be provided to the designated DND Representative (i.e. NDQAR, CONO Overseer, Technical Services Supervisor) if the waste material from the blast cleaning operation is classed as hazardous waste.

Scheduling/Deck Protection

3. Schedule deck preparation and painting work in high traffic areas or decks subject to other work during low activity periods. Isolate sources of contamination including pedestrian traffic. Cordon off deck areas and post OUT OF BOUNDS signs as necessary. Protect all deck coverings from damage until they are serviceable for traffic or until the end of the work period.

Parameters of Traffic and Non-traffic Areas

4. Prior to coating removal, record the traffic (non-slip areas) and non-traffic (dado I painted areas) for reference. Non-traffic areas are normally inaccessible to traffic, (i.e. under fixed shelving, desks, lockers, benches and equipment foundations). All coamings, deck fittings, exposed seatings and a minimum of 50mm (2 inches) around their perimeter are considered non-traffic areas. The top of flush hatches shall have non-slip coating applied with a 50mm (2 inch) perimeter painted boundary.

Temporary Sheltering

5. To maintain environmental conditions (for deck preparations and coating application) and to protect the environment (ref. Fisheries Act, Section 35), the RF shall:

• Totally enclose the decks being cleaned I prepared 100% to bare metal lAW SSPC-SP-5 Standards (White Metal Blast Cleaning) in a manner that would prevent the dispersion of particles into the air or release of any deleterious substances into the harbour. The RF shall capture and dispose of all used I drained liquids in accordance with all applicable municipal , provincial and federal regulations and legislation.

• For decks I areas only requ iring partial repairs and I or top-coat, install appropriate protection I hoarding I containment in a manner that will prevent the dispersion of particles into the air or release of any deleterious substances into the harbour. The RF shall capture and dispose of all used I drained liquids in accordance with all applicable municipal, provincial and federal regulations and legislation.

• Sweep I clean I scrape all areas of loose and I or flaking coatings to remove as much loose debris as possible and collect and dispose appropriately prior to cleaning to SSPC-SP-1 Standards (Solvent Cleaning) .

• . Cleaning products shall be used I mixed I diluted in accordance with manufacturer's recommendations I instructions.

• Coatings shall be applied by means of rollers and/or paint brushes to reduce VOC emissions and prevent over-spray into the water and I or atmosphere. If decks are fully enclosed I hoarded, spray application may be permitted.

• All enclosures I protection I hoarding shall be erected I installed to the satisfaction of FMFCS Safety I Environment personnel prior to the commencement of any work; and all enclosures I protection I hoarding shall be maintained to the satisfaction of FMFCS Safety I Environment personnel whi le in use for the duration of the paint coating project. Paint, paint chips or dust generated during paint removal shall not be permitted to enter the water. Containment booms shall be in place prior to the commencing any work, and any spillage shall be cleaned. Spill response kits for first level intervention shall be available on site for the duration of the coating I re-surfacing project.

• The ambient air temperature and substrate temperature during coating application and curing must be maintained within the coating manufacturer's recommended values. If required, provide a temporary shroud (for weather protection) or a fully enclosed shelter

4

R

NC*

H 1-23-003-00SIJ 1-003 (cold weather), to fully cover the boundaries of the deck area being treated. During cold weather, the ambient temperature inside the enclosure shall be maintained 24 hours per day at a minimum of rc. The designated DND Representative (i.e. NDQAR, CONO Overseer, Technical Services Supervisor) and I or FMFCS NACE Inspector shall inspect shelter.

• All work to be carried out in accordance with labour and environmental regulations within the jurisdiction that the work is carried out in.

Interference Removals

6. Interference removals required to gain access to all areas of the deck requiring coating repairs are to be determined by the RF during the viewing period. Areas requiring repairs are to be determined by the FMFCS NACE Inspector. Removals identified in this Job Instruction or any other relevant documentation(s) I specification(s) are only listed to assist the RF in bidding and are not to be considered all-inclusive or limited to those items listed.

a. Tag, disconnect, ease away or remove and retain all interference items clear of the work area, and suitably protect against damage. On completion of repairs, reinstall and re-secure items, utilizing with new fasteners, in accordance with the existing arrangement. On completion of re-installation, all disturbed equipment and systems are to be functionally tested and proven functional I operational. The RF shall certify and record functional test(s) . The designated DND Representative (i.e. NDQAR, CONO Overseer, Technical Services Supervisor) shall inspect.

Manufacturer's Material Safety and Technical Data Sheets

7. The manufacturer's published Material Safety Data Sheets (MSDS) and Technical Data Sheets (TDS) shall form part of this specification and shall be acquired by the RF. The dry film thickness (OFT) and the minimum I maximum cure times before application of subsequent coat are to be in accordance with the manufacturer's recommendation found in the TDS or by written confirmation from the Field Service Representative (FSR) . In case of conflict of information, the designated engineering authority (DEA) or FMFCS NACE Inspector shall be consulted. The final resolution I decision on any conflict of information shall be directed, through consultation with the LCMM, DNPS 2-4-4, 3nd I or the FSR, by the FMFCS NACE Inspector.

Materials

8. The RF shall supply all materials sufficient to comply with this specification and any other relevant do<;:umentation(s) I specification(s) . Provide manufacturer's names, product names, material TDS and material batch numbers. Materials shall not exceed manufacturer's stated shelf life. Refer to Annex C for listing of approved products. The use of any alternate product(s) shall be approved by the coating LCMM, DNPS 2-4-4, through the DEA or FMFCS NACE Inspector.

9. All coating material systems shall be supplied from the same manufacturer unless written consent, from the manufacturer, is provided to allow substitute coatings to be used without limitations and voiding warranties. If such consent is not obtainable from the manufacturer, the final resolution 1 decision shall be directed by the DEA or FMFCS NACE Inspector.

1 0. Deliver all materials to the work site in the manufacturer's sealed containers, bearing the manufacturer's labels, identifying product name, material type, colour, batch numbers, etc. Store materials in a dry space away from sources of spark or flame with temperatures ranging as per manufacturer's recommendations. The space shall be kept neat and clean at all times.

Pre-surface Cleaning

11. Clean the overall deck area to remove all loose flaking coatings, salts, grease, dirt, visible

5

R, NC*

R

H 1-23-003-00SIJ 1-003 and soluble contaminants in accordance with SSPC-SP-1 Standards (Solvent Cleaning), using a biodegradable cleaner I de-glossing agent, Code C415. Immediately after cleaning, thoroughly rinse with fresh water.

a.

b.

The RF shall dispose of all drained liquids in accordance with all applicable municipal, provincial and federal regulations and legislation.

The RF shall provide a Certificate of Disposal.

c. Carry out chloride ion testing in accordance with Para. 12.

Chloride lon Testing

12. Carry out chloride ion testing using semi-quantitative tests in accordance with SSPC-TU-4, Cell Retrieval Methods, Swabbing or Washing Methods, as follows;

a.

b.

c.

on completion of pre-surface preparation to SSPC-SP-1 (Solvent Cleaning) , and I or SSPC-SP WJ-4 (Waterjet Cleaning of Metals- Light Cleaning) to ensure the chloride ions are not imbedded into the substrate when cleaning to bare metal; and

on completion of substrate preparation, SSPC-SP-2 (Hand Tool Cleaning) , SSPC-SP-3 (Power Tool Cleaning) and SSPC-SP-11 (Power Tool Cleaning to Bare Metal) and I or SSPC-SP WJ-1 (Waterjet Cleaning of Metals- Clean to Bare Substrate), prior to coating application.

the FMFCS NACE Inspector shall witness the tests. Tests are to be recorded, by the RF, in Annex B;

d. The number of tests for each space I deck shall be determined by the amount of surface area being cleaned and treated.

e.

i. For areas less than 10 sq m {1 07 sq ft), a minimum of two (2) tests are required. Any additional requirement is optional at FMFCS NACE Inspector's discretion.

ii. up to 50 sq m (539 sq ft) one (1 ) test per every 1 0 sq m (1 07 sq ft) .

iii. 50 sq m (539 sq ft) to 200 sq m (2153 sq ft) one (1) test per every 20 sq m (215 sq ft).

iv. 200 sq m (2153 sq ft) to 500 sq m (5382 sq ft) one (1) test per 40 sq m (431 sq ft) .

v . 500 sq m (5382 sq ft) to 1000 sq m (1 0764 sq ft) one (1 test per 60 sq m (646 sq · ft) .

vi. 1000 sq m (1 0764 sq ft) to 2000 sq m (21528 sq ft) one (1) test per 100 sq {1 076 sq ft) .

vii. 2000 sq m (21528 sq ft) to 3000 sq m (32292 sq ft) one (1) test per 150 sq (1615 sq ft).

viii. 3000 sq m (32292 sq ft) to 4000 sq m (43056 sq ft) one (1) test per 200 sq (2153 sq ft).

ix. 4000 sq m (43056 sq ft) and up, one (1) test per 250 sq m {2691 sq ft).

the acceptable chloride ion level shall be less than 5 1Jg/cm2 (5ppm). Coatings shall not be removed or applied until this level of cleanliness is achieved; and;

f. Should chloride ion levels greater then 5 1Jg/cm2 (5ppm) be found, 100% of the areas

6

c

c

R, NC*

R, NC*

R, NC*

R,NC*

NC*

H 1-23-003-00SIJ 1-003 shall be re-cleaned as per Para 11 . On completion of re-cleaning, chloride ion testing shall be carried out as per this Para. This evolution shalll:>e carried out until acceptable chloride lon levels of less then 5 1Jg/cm2 (5ppm) is achieved. Re-cleaning of less than 100% of the total surface area shall be at the discretion of the DEA or FMFCS NACE Inspector.

NOTE: Should chloride ion levels greater then 5 1Jg/cm2 (5ppm) be found, the RF, the designated DND Representative (i.e. NDQAR, CONO Overseer, Technical Services Supervisor) and I or ship's staff shall investigate to find if a source of contamination is present. If a source of contamination is found, it shall be remediated prior to proceeding with pre-surface preparation and I or surface preparation and I or coating application.

Surface Preparation For Areas Requiring Repairs - Steel Substrate

13. Areas of steel deck requiring coating repairs are to be cleaned to bare metal in accordance with SSPC-SP-11 (Power Tool Cleaning to Bare Metal) or SSPC-SP WJ-1 (Waterjet Cleaning of Metals- Clean to Bare Substrate) to achieve a final surface condition as depicted in SSPC-VIS 3, E SP 11 or SSPC-VIS 4. On completion, the surface shall be free of all visible oil , grease, dirt, dust, paint, oxides, corrosion products, and other foreign matter.

NOTES:

(1) Any areas of exposed steel substrate exhibiting iron oxide (black) shall be re-cleaned to SSPC-SP-11 Standards by means of needle gunning and I or rotary scaler I NC* scarifier to remove the iron oxide and to achieve a final surface condition as depicted in SSPC-VIS 3, E SP 11 .

(2) Any areas of exposed steel substrate exhibiting any degree of polishing and I or burnishing shall be re-cleaned to SSPC-SP-11 Standards to achieve a final surface NC* condition as depicted in SSPC-VIS 3, E SP 11.

(3) All exposed appendages and projecting Sl,lrfaces shall be cleaned to bare metal up to a height of 1 OOmm (4 inches) above deck (i.e. bulkheads, ship sides, house sides, bulwarks, seatings, foundations, boundary bars, deck fittings, portable deck cover plates, coamings, etc).

(4) Edges of intact coatings bordering areas cleaned to bare metal shall be feathered back a minimum of 50mm (2 inches) to produce a smooth final transition I finish when NC* recoated .

(5) When waterjet cleaning in accordance with SSPC-SP WJ-1 and SSPC-SP WJ-2 Standards, the RF must be aware of and ensure that all environmental policies are upheld, such as the recovery of all effluents.


(7) Waterjet cleaning does not produce an etch or angular surface profile, rather it exposes the original abrasive-blasted or corroded surface profile. After waterjet NC* cleaning, should any area of the prepared surface not meet a minimum angular surface profile of 38.1 IJm, the RF will be responsible to achieve the specified profile as part of the original contract.

Surface Preparation For Areas Requiring Repairs -Aluminum Substrate

14. Areas of aluminum deck requiring coating repairs are to be power tool cleaned to bare metal in accordance with SSPC-SP-11 Standards (Power Tool Cleaning to Bare Metal) using 3M non-woven abrasive pads (or equivalent) or SSPC-SP WJ-1 (Waterjet Cleaning of Metals -

7

HI-23-003-00SIJ 1-003 Clean to Bare Substrate) to achieve a final surface condition as depicted in SSPC-VIS 3, E SP 11 or SSPC-VIS 4. On completion, the surface shall be free of all visible oil, grease, dirt, dust, paint, oxides, corrosion products, and other foreign matter.

NOTES:

(1) Any areas of exposed steel substrate exhibiting any degree of polishing and I or burnishing shall be re-cleaned to SSPC-SP-11 Standards to achieve a final surface condition as depicted in SSPC-VIS 3, E SP 11.

(2) All exposed appendages and projecting surfaces shall be cleaned to bare metal up to a height of 1 OOmm (4 inches) above deck (i.e. bulkheads, ship sides, house sides, bulwarks, seatings, foundations, boundary bars, deck fittings, portable deck cover plates, coamings, etc).

(3) Edges of intact coatings bordering areas cleaned to bare metal shall be feathered back a minimum of 50mm {2 inches) to produce a smooth final transition I finish when recoated.

(4) When waterjet cleaning in accordance with SSPC-SP WJ-1 Standards, the RF must be aware of and 6nsure that all environmental policies are upheld, such as the recovery of all effluents.


(6) Waterjet cleaning does not produce an etch or angular surface profile, rather it exposes the original abrasive-blasted or corroded surface profile. After waterjet cleaning , should any area of the prepared surface not meet a minimum angular surface profile of 38.1 IJm, the RF will be responsible to achieve the specified profile as part of the original contract.

Surface Preparation Inspections

15. The RF shall carry out the following inspections on completion of surface preparation. If oxidation occurs between cleaning to bare metal and coating application, the surface shall be re-cleaned to bare metal to the specified standard. Any areas subject to contamination after cleaning to bare metal shall be cleaned I degreased in accordance with SSPC-SP-1 Standard. The RF shall certify and record inspections and verify the surface has been prepared in accordance with this specification. The FMFCS NACE Inspector shall witness each inspection point.

a. Visual Inspection- surface preparation verified in accordance with SSPC-VIS 1-89, SSPC-VIS 2, SSPC-VIS 3 or SSPC-VIS 4, or SSPC-VIS 5.

b. Visual Cleanliness Inspection- surface on final inspection is to be free of dust and visible contamination. Verify cleanliness by placing a clear adhesive tape, pressed on the surface at several locations that is representative of the entire area, and remove. When viewed, the removed tape shall be free from any visible dust, dirt, and other contaminants.

NOTE: For steel decks prepared to SSPC-SP WJ-1 Standards; all areas shall meet flas:1 rust conditions of "no flash rust" to "light flash rust" as described

A/C*

A/C*

R, A/C*

in SSPC-SP WJ-1 Standards. All areas not meeting the required R, A/C*

c.

Standard prior to coating application shall be re-cleaned until the required Standard is met.

Non-visual Cleanliness Inspection- carry out chloride ion testing lAW Para 12 of this specification and record in Annex B.

8

R, A/C*

H 1-23-003-00SIJI-003

d. Surface Profile Measurements - measure and record surface profiles in accordance with NACE RP0287-95 and the RF shall record in Annex"A.

Structural Inspection

16. On completion of cleaning the deck to bare metal lAW SSPC-SP-2 I 3 I 11 and I or WJ-1 Standards, and prior to any coating application, sufficient time shall be allotted for a OEA or FMFCSIENGINAOIHull Surveyor to carry out a structural survey of all exposed substrate. Any damage I wastage found , not within acceptable Standards, arising from the structural survey will be raised as item(s) of additional work. Should any damage I wastage be found , the OEA or FMFCSIENGINAOIHull Surveyor will forward a detailed description of findings to the designated ONO Representative (i.e. NOQAR, CONO Overseer, Technical Services Supervisor) and the Ship's Senior Hull Technician.

Pre-coating Application Inspections

17. The RF shall ensure that surface preparation is as specified in Para 15 of this specification .

R, A/C*

A!C*

Environmental conditions in accordance with the following or as recommended by the coating R, A/C* manufacturer are not to be exceeded during the coating application process. The FMFCS NACE Inspector shall witness each inspection point:

a. ambient temperature not less than r C;

b. surface temperature 3° C above dew point and not to exceed 49° C; and

NOTE: International products lntershield 300, lntershield 6GV, and lntercryl 588 have a maximum temperature of sooc for application purposes.

c. relative humidity (RH) below 85%.

NOTE: Ambient temperature, surface temperature, dew point, and RH shall be recorded by the RF prior to the start of each coating application and as required thereafter to R, A/C* verify that specified parameters are within specification and 1 or at the discretion of the FMFCS NACE Inspector.

Treatment- Steel and Aluminum Substrate Primer System

18. a. Areas of steel decks that can not be cleaned to SSPC-SP- 11 or WJ-1 Standards shall be cleaned to SSPC-SP-2 or 3 to the fullest extent possible and coated with one (1) coat of Two-component Epoxy Rust Penetrating Primer I Sealer, Code C406, to a OFT as per manufacturer's instructions, prior to application of 1st coat of epoxy primer, Code C420.

b. A stripe coat shall be applied to all edges, deck fittings, coamings, seatings, weld seams, etc, previously cleaned to bare metal, using an epoxy primer, Code C420. Stripe coating shall encompass all edges as well as at least a 25mm (1 inch) border outside each edge. The stripe coat shall be neat in appearance and free from runs, sags or curtains. The stripe coat shall be allowed to dry, at least set to touch, before the full first coat is applied.

c. Apply one (1) or more coats as required, using alternating colours, of an epoxy primer, Code C420, once the stripe coat has been allowed to dry, at least set to touch , to the overall prepared surface, to a minimum OFT of 150 IJm.

d. Within the recommended re-coat period, apply one (1) coat of an epoxy primer, Code C420, using alternating colours, to the overall primed I prepared surface, to a minimum OFT of 125 1-1m to 150 IJm.

e. The final OFT for the primer system shall be between 250 1-1m to 300 IJm. Any areas not conforming to the minimum OFT requirement shall be re-coated, within the recommended re-coat period , using alternating colours. The minimum OFT requirement shall be

9

H 1-23-003-005/J 1-003 achieved prior to application of any subsequent coating system.

NOTES:

(1) There shall be no application of epoxy primer, Code C420 on existing I remaining non-slip and I or non-traffic coating. If application of epoxy primer, Code C420 occurs on existing I remaining non-slip and/or non-traffic coating, it shall be immediately removed prior to curing.

(2) Mixing of coatings is only allowable with the permission of the FMFCS NACE Inspector, and shall be done lAW manufacturer's instructions I mix ratio and shall be appropriately mixed I measured using suitable graduated mixing sticks and I or containers.

Steel and Aluminum Substrate Non-slip Traffic Areas Repairs

19. a.

b.

c.

Apply to primed traffic areas a non-sl ip, epoxy deck coating, Code C419, colour US Fed-Std-5958 #36076, flat dark grey. Actual coverage rate shall be in accordance with manufacturer's specification .

With the material freshly stirred, in accordance with manufacturer's specification I recommendations, to evenly disperse aggregate, pour substantial portion of mixture onto the deck in a band approximately 450mm to 600mm {18 to 24 inches) wide. Using a smooth phenolic core roller, spread non-skid coating evenly by pulling the puddle towards the applicator, that is one (1) direction only. Avoid back and forth roller motion. With puddle nearly rolled out, pour additional mixed material over remaining puddle and continue application as above.

The final finished surface shall present a uniform rough appearance over the entire surface. No loosely bound clumps of particles shall be present. The surface profile shall show a pattern of hard raised peaks, 1.5 - 2.4mm (1 /16 to 3/32 inch) high and 12.5- 25mm (%to 1 inch) apart. The dry non-skid coating at its thinnest point shall be at least 750 IJm.

NOTE:

1. A sample panel depicting the textured finish of the non-skid coating that must be achieved is available for viewing through the FMFCS/NAO/Hull Surveyors.

Steel and Aluminum Painted Non-Traffic Areas Repairs

20. a. For non-traffic areas, on decks being repaired and top-coated with Exterior Alkyd Marine Enamel Topcoat,

(1) apply one (1 ) or more coats, as required, of an epoxy tiecoat, Code C426, over the already applied epoxy primer, Code C420, within the manufacturer's recommended re-coat time, to a minimum DFT of 50 to 1 00 IJm followed by;

(2) two (2) coats of Exterior Alkyd Marine Enamel Topcoat, Code C061 to all primed deck non-traffic I Dado areas, complete with appendages I projecting surfaces 1 OQmm (4 inches) above the deck, to DFT of 40 to 60 IJm per coat, within the manufacturer's recommended re-coat time. The colours shall be in accordance with existing colour scheme and US Federal Standard 5958, colours Grey 16076 and Black 17038.

b. For non-traffic areas, on decks being repaired with Polyurethane, Two Component Topcoat,

10

R,NC*

NC*

NC*

H 1-23-003-005/J 1-003

(1) apply, two (2) coats of polyurethane, two component topcoat, Code C177 to all primed deck areas to OFT of 40 to 50 IJm per coat, within the manufacturer's recommended re-coat time. The .colours shall be in accordance with existing colour scheme and US Federal Standard 595B, colours Grey 16076 and Black 17038.

c. Appendages I Projecting Surfaces:

Markings

(1) Apply, two (2) coats of Enamel, Silicone Alkyd Copolymer (LSA) Topcoat, Code C411 to bulkheads, ship sides, house sides, bulwarks and surfaces projecting above the 1 OOmm (4 inches) non-traffic/Dado areas, in accordance with the existing colour scheme.

21 . Apply affected warning and control markings in accordance with the applicable drawing or in accordance with the existing arrangement if no drawing is available. Locations of Warning and control markings shall be noted and recorded, by the RF, for reference prior to coating removal.

a. apply markings on non-slip, traffic areas, using two (2) coats of Code C177, polyurethane two-component topcoat. OFT to be in accordance with manufacturer's specifications. To prevent markings in traffic areas from becoming slippery, one (1) part aggregate (glass beads) shall be mixed to five (5) parts paint. Colours shall be in accordance with US Fed-Std-595B: Yellow- 33538; White- 37925; Red- 11350, and Black- 17038.

b. apply markings on non-traffic areas, using two (2) coats of Code C061 , Exterior Alkyd Marine Enamel Topcoat. OFT to be in accordance with manufacturer's specifications. Colours shall be in accordance with US Fed-Std-595B: Yellow - 33538; White-37925; Red- 11350, and Black- 17038.

Top-coating - Preparation and Application

22. Preparation- If major coating repairs have been carried out, the entire deck is to be recleaned as per paragraph 11 and chloride ion tests conducted as per Para. 12. prior to the application of any topcoat (cosmetic coat) .

a. Application of Top-coat on Existing and Repaired Non-slip Coatings:

(1) Apply a single coat of Low Solar Absorbant waterborne non-skid deck finish, Code C423, in accordance with manufacturer's instructions I recommendations to achieve a final OFT of 50 to 60 IJm.

NOTE: Caution is to be exercised not to apply the Code C423 topcoat over the non-traffic areas and painted warning and control markings on the decks.

b. Application of Top-coat on Existing and Repaired Non-traffic Coatings:

(1) Apply One (1) coat of polyurethane Code C177 or one (1) coat of Exterior Alkyd Marine Enamel as per existing coating and colour scheme or as specified in any other relevant documentation(s) I specification(s) .

c. Top-coat on Markings: Non-slip deck coating:

(1) Apply markings to any affected areas on non-slip, traffic areas, using two (2) coats of Code C177, polyurethane two-component topcoat. OFT to be in

11

R

R, AC*

RNC*

R, NC*

R, NC*

R, A/C*

H 1-23-003-00SIJ 1-003 accordance with manufacturer's specifications. To prevent markings in traffic areas from becoming slippery, the second coat shall have one (1) part aggregate (glass beads) mixed to five (5) parts paint. Colours shall be in accordance with US Fed-Std-595B: Yellow- 33538; White- 37925; Red-11350, and Black - 17038.

d. Top-coat- Markings on non-traffic deck coating:

(1) Apply markings to any affected areas on non-traffic areas, using two (2) coats of Code C061, Exterior Alkyd Marine Enamel Topcoat. DFT to be in accordance with manufacturer's specifications. Colours shall be in accordance with US Fed-Std-595B: Yellow- 33538; White- 37925; Red-11350, and Black- 17038.

NOTE: Apply warning and control markings in accordance with the applicable drawing or in accordance with the existing arrangement if no drawing is available. Locations of warning and control markings shall be noted and recorded, by the RF, for reference prior to coating removal.

Coating Inspections Post Applit;ations - OFT Measurements

23. The RF shall carry out DFT measurements in accordance with SSPC-PA-2 and shall record their readings in Annex A. The FMFCS NACE Inspector shall witness each inspection I test.

a. OFT measurements of each coating application shall be taken on completion of curing time as per manufacturer's recommendations and/or prior to the next coating application.

b. The DFT measurements for each coating system shall not fall outside the specified parameters. Should the DFT measurements, for each coating system, fall outside the specified parameters, the areas not meeting the minimum DFT requirements shall be remediated I recoated and the required DFT measurements shall be achieved prior to application of a subsequent coating system.

c. DFT measurements shall be taken after final coating application, on completion of curing time as per manufacturer's recommendations. Areas not having sufficient build of coating shall be re-coated until the required final DFT is achieved.

Vertical Launch System (VLS) Launcher Top- IRO Class

24. THE VLS LAUNCHER TOP SHALL NOT BE PREPARED AND TOPCOATED UNDER THIS SPECIFICATION. UNDER NO CIRCUMSTANCES SHALL THE RF ATIEMPT ANY REPAIR OF THE VLS LAUNCHER TOP.

Preparation and Coating Requirements

25. Select all equipment used for surface preparation and coating application to be effective and economical to produce the requ ired surface finish. Selected equipment is to be properly maintained in good working order and only operated by trained personnel.

26. Operate equipment with clean compressed air, free from oil and moisture. Compressed air supply shall be fitted with oil and moisture traps with adequate capacity to produce the desired air pressure and volume. Verify cleanliness of the air supply at the beginning of each shift by conducting a blotter test in accordance with ASTM D-4285 - Indicating Oil and Water in Compressed Air.

27. Maintain surface preparation and coating conditions in accordance with Para. 15 and 17 of this specification.

12

R, NC*

R

R, NC*

R

28. H 1-23-003-005/ J 1-003

Before placing the deck area back into service, allow sufficient curing time for the final coating

29.

system, as per the coating manufacturer's recommendation found on the technical data sheet. The work area is to be well ventilated, with controlled ambient conditions during the curing process.

Clean, inhibit, prime and paint new and disturbed work in accorqance with appropriate part 1 section of the latest edition of D-23-003-005/SF-002 (Maintenance Painting of HMC Ships) and manufacturer's instructions. Any conflict between the maintenance painting manual, the manufacturer's instructions and I or this specification shall be brought to the attention of the DEA and I or the FMFCS NACE Inspector for clarification and I or resolution. The final resolution I decision on any conflict of information shall be directed, through consultation with the LCMM and I or the FSR, by the DEA or FMFCS NACE Inspector.

Inspections

30. The RF shall have a NACE CIP Levell I Coating Inspector on staff to conduct self-inspections and supply the required documentation to the DND Representative (i.e. NDQAR, CONO Overseer, Technical Services Supervisor) IDEA I FMFCS NACE Inspector upon request.

a. Inspection hold points are indicated in the right hand column throughout the specification. The RF shall advise the designated DND Representative IDEA I and I or FMFCS NACE Inspector in sufficient time to be present for the inspection.

b. When the symbol "NC" or "NC*" appears in the right hand margin of a specification, it indicates a stage in the work, as specified in the Description of Work Required, that the designated DND Representative (i.e. NDQAR, CONO Overseer, Technical Services Supervisor) shall be advised by the RF in sufficient time to have a designated DND Representative IDEA I and I or FMFCS NACE Inspector as specified, present during the RF's inspection I examination. The RF retains the sole responsibility for conducting the inspection I examination and for producing the required objective evidence required by the Description of Work.

NOTE: Should the RF proceed with further work as described in the specification without advising the designated DND Representative IDEA I and I or FMFCS NACE Inspector in sufficient time to be present, the RF shall be required to re-open the equipment I system and I or re-clean the deck to bare metal for the required inspection I examination I validation by the designated DND Representative without cost nor prejudice to the Crown.

c. "A/C" point- The attendance of a designated DND Representative IDEA I and I or FMFCS NACE Inspector during the RF's inspection I examination is annotated as an "NC" point and is at the discretion of the designated DND Representative I DEA I and I or FMFCS NACE Inspector.

d. "A/C*" point- The attendance of a designated DND Representative IDEA I and I or FMFCS NACE Inspector during the RF's inspection I examination is annotated as an "NC*" point and is deemed critical, therefore, the designated DND Representative I DEA I and I or FMFCS NACE Inspector shall be in attendance.

e. Defects/Reading Points- When the symbol "D" (defects) or "R" (readings) appear in the right hand margin of a specification it indicates a stage in the work as specified in the Description of Work Required, that the RF shall record, in writing, the data required in the Description of Work. Unless a format is specified in the appropriate Description of Work Required, the RF shall provide its own format(s) for reporting readings and defects. Format(s) used by the RF shall be suitable for accurate photocopying when completed. The RF shall forward the recorded data immediately to the FMFCS NACE Inspector unless otherwise specified.

f. Inspection equipment shall be held and used by the RF for tests performed. All measuring/recording equipment shall be calibrated in accordance with the

13

R

R

R

H 1-23-003-005/J 1-003 manufacturer's recommended practice, recorded and records delivered to the FMFCS NACE Inspector upon request.

g. Environmental Certificates of Disposal Required- When the symbol "C" appears in the right hand margin of a specification, it indicates that a signed Environmental Certificate of Disposal is required for the work as specified in the Description of Work Required. This certificate shall confirm to Canada that the environmentally hazardous substance is lawfully disposed of in accordance with all applicable Municipal, Provincial and Federal regulations and legislation.

Inspection Equipment

31. Inspection equipment and standards to be held and used by the contractor for tests performed:

a. surface thermometers;

b. air thermometers;

c. sling psychrometer and/or digital environmental gauge;

d. replica tape and micrometer and/or digital surface profile gauge;

e. dry film coating thickness gage;

f. wet film coating thickness gage;

g. standards, in accordance with page 2, Related Documents; and

h. chloride ion test kits .

Workmanship

32. a. All work shall be free from runs, sags, curtains, holidays or other visible defects such as blisters resulting from solvent entrapment.

Safety

b. There shall be no uncoated areas. Areas not having sufficient build of coating shall be re-coated until the required final DFT is achieved.

c. There shall be no loosely bound clumps of non-skid particles.

d.

e.

f.

g.

h.

Edges of intact coatings bordering areas cleaned to bare metal shall be feathered back a minimum of 50mm (2 inches) to produce a smooth final transition/finish when recoated.

The intersection of traffic and non-traffic areas shall be straight and neat in appearance.

When cleaning areas of non-slip deck coating requiring repairs to bare metal, areas shall be straight and neat in appearance;

All personnel entering the work area shall wear coveralls, clean boots and gloves to minimize contamination of the surfaces. The entrances to the work area shall have an area to wipe soles of boots clean.

On completion of all work, the work site shall be free from work related debris or unused materials. Particular care is to be taken to ensure all scattered debris, paint chips are removed from recess, sockets, deck fittings, ventilation inlets, etc.

14

NC*

H 1-23-003-005/J 1-003

33. Attention is drawn to the highly inflammable nature of the specified coatings and their solvents. Care must be exercised to ensure adequate ventilation is provided to prevent against toxic hazards and explosive concentrations of vapors and that sources of ignition are eliminated from areas where such concentrations could occur.

34. The RF shall comply with the requirements of all MSDS and all safety regulations in accordance with applicable federal and provincial regulations. The following acts and regulations apply: ~

a. Occupational Safety and Health, Part 11, Canada Labour Code;

b. Occupational Safety and Health, Policy Volume of the TB Manual;

c. DND Safety Legislation and Policy, C-02-040-009/AG-000; and

d. DND Safety Policy and Programs, A-GG-040-001/AG-001.

35. The RF shall comply with all safety requirements in accordance with applicable federal , provincial and municipal regulations and legislation.

Environmental Regulations and Requirements

36. The RF shall remove, handle, store, transport and dispose of all hazardous waste in accordance with all applicable federal , provincial and municipal regulations and legislation. Precautions shall be taken during cleaning and painting , to protect the ship's equipment and the environment from contamination. The RF shall take precautions during coating removal operations as coatings may contain heavy metals, such as lead and chromates. The RF shall subject solid waste, i.e. used blast media, to Leachate testing to determine appropriate disposal option. The RF shall provide a Disposal Certificate if the waste material from the cleaning operation is classed as hazardous waste.

a. The RF shall comply with the following acts:

(1) the Canadian Environmental Protection Act; and

(2) the Canadian Fishery Act.

Environmental Aspects

37. The following environmental aspects have been identified for the above work specification. This list shall not be considered to be all inclusive and does not remove the responsibility of the RF to identify all the environmental aspects related to this work specification:

a. Air Emissions: power wash cleaning, abrasive blasting, power tool cleaning, coating application;

b. Hazardous Materials: degreasers, solvents, epoxy primers, polyurethane, epoxy nonskid coating;

c. Hazardous Waste: cleaning waste, spent abrasive grit, paint chips, paint waste;

d. Noise Emissions: power wash cleaning, abrasive blasting, power tool cleaning, coating application;

e. Non-hazardous Solid Waste: paint waste;

f. Process Water: high pressure wash , degreaser; and

g. Spills/Releases: degreaser, paint and solvents.

15

c

H 1-23-003-005/J 1-003

Deliverables

38. The RF shall forward the following deliverables to the designated DND Representative (i.e. NDQAR, CONO Overseer, Technical Services Supervisor) within five (5) working days of work completion:

a. Preparation and Coating Application Recording Form, Annex A;

b. Chloride Ions Testing Recording Form, Annex B; and

c. Disposal Certificates.

16

R

c

H 1-23-003-005/J 1-003 ANNEXA


SSPC-SP-12

SSPC-SP-1

SSPC-SP-2

SSPC-SP-3

SSPC-SP-11

SSPC-SP-5

SSPC-SP-10

SSPC-SP-7

RF'S NAME (PRINTED) : DATE: RF'S SIGNATURE:

>,~ •y~r,r:=·"'D7Jllf~'S:"m'''' ""ff'"'2"'["m'''~~"'W~[:"IWN~~~-- ~r·=~~:~~ " 0 " ' , ~il~<- ) ~ f ' V ) ~ .;<) ";_! ~ & ;, < , ~ ~ Ai

~~~'*->v~"*'' '' ',,/~',,kl' -~·" """ ~~» &=~ «c' ""~-">'v,_iftJ .,_=~w >:>;!~~~(( !> » -~"W:''"'-'"''-,.j,ifuci4WJ,ii;;_,~

MANUFACTURER'S PRODUCT NAME

BATCH NO,

COLOUR NO,

QUANTITY USED {Number of gals/kits)

SURFACE TEMP

AMBIENT MIN

TEMP MAX

RELATIVE HUMIDITY

DEW POINT

WET BULB TEMP

OFT SPECIFIED

OFT ACHIEVED

INITIALS

DATE

RF'S NAME (PRINTED): I DATE: RF'S SIGNATURE:

A-1

H 1-23-003-005/J 1-003 ANNEX B


SHIP'S NAME:

Reason for Testing:

AFTER CLEANING TO AFTER CLEANING TO SSPC-SP-2/3/11 AND/OR

COMPARTMENT AREA TESTED SSPC-SP-1 AND/OR 12 12-WJ-1 (in 1JQ/cm2

) (Prior to Coating) Jin IJQ/cm2

)

RF'S NAME: I RF'S SIGNATURE: DATE:

B-1

H 1-23-003-005/ J 1-003

ANNEXC

NAVAL SPECIFICATION MATERIAL LIST

SHIP/CLASS: DATE:

Jl NO: HI-23-003-003/JI-001 Jl AMENDMENT:

(1) (2) (3) (4) (5) (6) (7) (8) (9)

Line Dwg Number Stock Number Description/Part No. Qty Unit GSM CFM Remarks Item 1001 Code C406, Two-Component As X Approved Products:

Epoxy Rust Penetrating Req'd PPG Amerlock Sealer; Carboline Primer/Sealer Rustbound Penetrating Sealer;

Sherwin Williams Macropoxy 920 Pre-prime; Hempel Pre-prep 553US, lnternationallnterbond 600; Cloverdale Clovadale Prep Tech 83020

1002 Code C420, Epoxy Primer for As X Approved Products: Epoxy Non-skid Req'd International lntershield 300; Sherwin

Williams Seaguard 6000; PPG Amercoat 83HS; Jotun Jotamastic 87 Aluminium

1003 Code C177, Polyurethane Two- As X Approved Products: Component Req'd International lnterthane 990; PPG

Amercoat 450H; Carboline Carbothane 134 HG; Sherwin Williams Sherthane; Hempel Hempathane Top Coat 5521 0; Dupont lmron Single Stage System; Cloverdale Clovathane 834

1004 Code C419, Epoxy Non-skid As X Approved Products: Req'd lnternationallntershield 6GV (or

International lntershield 9G for cold weather); PPG Amercoat 138G; Sherwin Williams MS-660G; or Hempel MS-660G

-

C-1

H 1-23-003-005/ J 1-003

1005 Code C423, Low Solar As X Approved Products: Absorbant waterborne Non-skid Req'd International lntercryl 588; Sherwin Deck Finish Williams American Safety LSA - Traxcoat (Available in colors: gray

33076 and white 37875); or PPG Amercoat 220 with walnut shells.

1006 Code 061 Exterior Alkyd Marine As X Approved Products: Enamel Req'd PPG Amercoat 5450, black 17038,

grey 16480 and white 17925, all colours; General Paints Marine Enamel, all colours; Cloverdale Paint Inc. , 11113 Marine Enamel, white 17925, black 17038, grey 16480, all colours; lnternationallnterlac 665, Alkyd Finish, all colours; Sherwin Williams Seaguard 1000, N41 -620 Series, Alkyd Finish, all colours; Hempel Hempalin 52140, all colours

1007 Code 426 Epoxy Tie Coat As X Approved Products: Req'd lnternationallntergard 263; Hempel

Hempadur 45182; Jotun Safeguard Universal ES, grey.

1008 Code C415, Biodegradable As X Approved Products: Cleaner, De-glossing Req'd International 950- GMA 571 ; PPG Agent Amercoat Prep 88; or Sherwin

Williams Greensolv G-Max 308. 1009 Code C411 , Enamel, Silicone As X Approved Products:

Alkyd Copolymer (Low Solar Req'd lnternationallnterlac 1; PPG Absorption Pigmentation and Amercoat 7229C; Sherwin Williams Antistain Properties) Silicone Alkyd Enamel, N40A-

510; Hempel Silicone Alkyd Enamel 541 US; or Cloverdale Alkyd, Type 2, Class 2, Grade C.

C-2

4

•

PREVIOUS DND NO.

8355538

DRAWING REFERENCE TABLE

TITLE DRAWING NUMBER

8455722

FORMER DND NUMBER

HFX-D28-459-000-021

NO.

HULL INSULATION THERMAL AND ACOUSTIC KEYPLAN

2 HFX-D28-459-000-01 8553043DECK COVERING SCHEDULE

3 8555551HFX-D28-589-000-09DRAUGHT MARKS AND EXTERIOR HULL ATTACHMENTS ARGT & DETAILS

04-10-22- JD DM

ZONELTR

LETREVISION DATE

DWN

DES

CKD

VER

APPVL

APP

DMSS

2ALL

THIS DRAWING SUPERSEDES

8355538 REV.D

INCORPORATED: EC 19950519

BKHD REMOVED BETWEEN

CABIN 6 & 8. DC ZONE 2FX2

REMOVED. BKHD ADDED TO

OPERATIONS ROOM ADMIN

AREA. FEMALE OFF. CABIN

ADDED, DC ZONE 2DZ4

OPS. RM ADMIN AREA NOW

DC ZONE 2DY4

TDAN: 04HFXIRO0377

05-02-10A DM DWDMSS

2VAR.

DRAWING REVISED AS PER RTM

051189KP DATED 05-JAN-20.

HANGAR TOP LATERAL LINES ADDED

TO SHEET 9. HANGAR FACE & TOP

MARKINGS LISTING CHANGED FROM

BLACK TO YELLOW

TDAN: 05HFXIRO0124

VAR. DWDMSS

2B JL08-02-27

DRAWING REVISED AS PER RTM

080010007KP DATED 07-JAN-24.

INCORPRATED EC’S 19960333,

20020280, 20050023 & LCMM

DIRECTION TO UPDATE NBC

NOMENCLATURE TO CBRN,

DATED 07-02-27

TDAN: 08HFXIRO0101

VAR. JLCINCORPORATION OF EC 20050011

SOLID WASTE HANDLING

COMPARTMENT

TDAN: 10HFXIRO0370

UNCLASSIFIED

18 7 6 5 4 3 2

B

C

D

Huitiemes

Eighths 0 9876 1054321

Dixiemes

Tenths

Milli

metres

Milli

metres

02

04

06

08

01

00

12

0140

160

180

200

18 7 6 3 2

D

AA

DESIGN AGENT/CONCEPTION

DIMENSIONS ARE IN/DIMENSIONS SONT EN:

DRAWING DATE DU DESSINNSCM/CAOF

DRAWING NO. DU DESSIN

DWN/DESS CKD/VER QA/AQ

APPLICATION/USAGE

CF APPVL/APP FC

DRAWING INTERPRETATION

INTERPRETER LE DESSIN PAR

CF D-01-400-001/SG-000

LEVEL/NIVEAU-

ORIGINAL SCALE/ECHELLE ORIGINALE

DATA LIST/LISTE DE DONNEES

TITLE/TITRE

REVSHEET OF

FEUILLE DE

A1

(2004)HER MAJESTY THE QUEEN IN RIGHT OF CANADAC

MILLIMETRES

NTS

HFX-D28-396-000-01

DL-28-396-000-00D.WHITE D.MUSICK

2004-09-02DGMEPM 36219ISSC

C

PAINTING AND PRESERVATION

SCHEDULE2

DMSS 2

UNCLASSIFIED

-HFX

CLASS

1 81

SELECTED CLASS

10-06-14 CGT DMSS

2

Dwg No: HFX-D28-396-000-01 Previous DND No. 8355538 Date: 2004-09-02

INDEX

1

2

3

KEY PLANS

COVER SHEET

INDEX

GENERAL NOTES

10

MATERIALS

4, 5 & 6

MARKINGS & DETAILS 7 TO 9

SAMPLE PAINT LAYOUTS

UNDERWATER HULL

DC ZONE 6A TO 6L

DC ZONE 5C TO 5J

DC ZONE 4B TO 4M

DC ZONE 3B TO 3M

DC ZONE 2A TO 2M

DC ZONE M (MEZZ. DK.)

DC ZONE 1D TO 1M

DC ZONE 01D TO 01J

DC ZONE 02E TO 02J

TITLE SHEET NO.

Title: Painting & Preservation Schedule

WEATHER DECKS & MISC.

SHEET 2 OF 81

11 TO 13

14

15 TO 19

19 TO 23

23 TO 29

29 TO 40

40 TO 61

61

61 TO 70

70 TO 74

74 TO 75

75 TO 81

Rev: C

Dwg No: HFX-D28-396-000-01 Previous DND No. 8355538 Date: 2004-09-02Title: Painting & Preservation Schedule

4. PRIOR TO PAINT SYSTEM, APPLY ONE COAT(130 UM) OF D-28-155-001/SF-002 TYPE I. (NOT REQUIRED ON FIBERGLASS LINING IN WET SPACES AND CLEANSING STATIONS)

6. METALLIC MATERIALS USED IN FABRICATION SHALL BE SUPPLIED TO THE ASSEMBLY SITE IN A CORROSION-FREE CONDITION AND MEETING THE DIMENSIONS SPECIFIED.

9. BOOT TOP AREA (4400 TO 5600mm WATERLINES)

TREAT THE SAME AS FOR UNDERWATER HULL WITH THE FOLLOWING EXCEPTION,

A) THE FINAL TWO COATS OF ANTI-FOULANT SHALL BE BLACK IN COLOUR.

10. PRE-DELIVERY - UNDERWATER HULL AND BOOT TOPPING EXISTING PAINT SYSTEMS SHALL BE CLEANED AND TOUCHED UP AS REQUIRED.

12. WEAPONS ARE RECEIVED, PAINTED AND MAY ONLY REQUIRE TOUCH-UP PRIOR TO COMMISSION.

13. ANIT-CONDENSATION INSULATION ON STEEL BULKHEADS FROM SHELL TO 400mm MIN. INBOARD TO BE TREATED IN ACCORDANCE WITH NOTE 4 PRIOR APPLICATION OF PAINT FINISHER.

14. PROPELLER MARKINGS LEAD SHIP ONLY IN ACCORDANCE WITH SJSL DWG NO. 01-8315-6-2040.

15. ALUMINUM SUPPORT STRUCTURE FOR FALSE DECKS NOT TO BE PRIMED OR PAINTED.

18. ADD COLOUR PIGMENT TO THE FIBREGLASS RESIN AT INSTALLATION IN WET SPACES (SHIPS FFH333 & FFH336 - FFH341 ONLY) FOR DETAILS SEE REFERENCE DRAWING 1.

GENERAL NOTES:

20. THE MISC. SECTION ADDRESSING THE PIPING IS NOT INTENTED TO BE AN EXHAUSTIVE LIST DEFINING THE PAINTING, BUT AS A GUIDE FOR THE PAINTING OF VARIOUS METALS. PIPING, HANGERS AND SEATINGS WITHIN FUEL OIL TANKS,

POTABLE WATER TANKS, BALLAST TANKS, FEED WATER TANKS, SEWAGE TANKS, BILGES, VOIDS, COFFERDAMS, INTERIORS OF TRUNKS, INTAKES AND CASINGS SHALL BE PAINTED WITH THE SAME COATING SYSTEM SPECIFIED FOR THE SPACE.

11. PRIMERS OR COATINGS DAMAGED BY WELDING, ABRASION OR OTHER ABUSE SHALL BE CLEANED TO BARE METAL AND MAINTAINED BY SYSTEM TOUCH UP. INORGANIC ZINC PRIMER CODE C171 SHALL BE TOUCHED UP WITH ZINC RICH EPOXY PRIMER CODE C183.

CLEANING AND TOUCHING UP SHALL BE CARRIED OUT IMMEDIATELY WHEN THE DAMAGE IS DISCOVERED.

17. SONAR DOME FAIRING (FIBREGLASS) & SHAFTS (FIBRESLASS SHEATHED)

A) SURFACE PREPARATION: LIGHTLY SAND WITH 120-180 WET OR DRY PAPER WIPR DOWN WITH INTERLUX 202 FIBREGLASS SOLVENT WASH.

B) APPLY FIRST PRIMER COAT (INTERNATIONAL GELSHELD 200) APPROXIMATELY 1/2 HOUR AFTER SOLVENT WASH.

C) APPLY SECOND PRIMER COAT (INTERGARD 264) APPROXIMATELY 2 TO 3 HOURS AFTER FIRST PRIMER COAT.

D) APPLY THIRD PRIMER COAT (INTERGARD 263) WITHIN APPROXIMATELY 14 DAYS OF SECOND PRIMER COAT.

E) APPLY FIRST AND SECOND FINISHER COATS OF ANTI-FOULANT AT APPROXIMATELY 24 HOURS INTERVALS FROM THIRD PRIMER COAT.

F) APPLY THIRD COAT OF ANTI-FOULANT AT THE TIME OF DOCKING PRIOR TO TRIALS AS PER NOTE 8 ABOVE.

3. ALL COLOUR CODES IN THIS SCHEDULE ARE IN ACCORDANCE WITH FEDERAL STANDARD 595B COLOURS.

7. SURFACE PREPARATION:

A) PRIOR TO PAINT APPLICATION, ALL STEEL STRUCTURES SHALL BE BLAST CLEANED IN ACCORDANCE WITH SPECIFICATION ANSI A159.1-1972. THE SURFACE PREPARATION SHALL BE AS DETAILED IN OTHER PARTS OF THIS SCHEDULE OR A STATED IN THE FOLLOWING NOTES.

B) THE QUALITY CONTROL INSPECTION SHALL BE MADE DURING THE BLASTING PROCESS. SPECIFIED PRIMER SYSTEMS SHALL BE APPLIED WITH A MINIMUM OF DELAY AFTER BLASTING/CLEANUP AND SHALL BE APPLIED TO A SURFACE FINISH OF AT LEAST SSPC-SP10-2004/NACE NO.2

(SA 2 1/2)

C) THE EXTERIOR SURFACE PREPARATION OF ALL STEEL UNITS SHALL BE BLAST CLEANED TO WHITE METAL IN ACCORDANCE WITH SECTION SSPC-SP5-2004/NACE NO.1 (SA3) OF SPECIFICATION ANSI A159. 1-1972. (MAINTAIN AT SA 2 1/2 PRIOR TO COATING).

D) THE INTERIOR SURFACE PREPARATION OF ALL STEEL UNITS SHALL BE BLAST CLEANED TO NEAR WHITE METAL AND MAINTAINED TO STANDARD SSPC-SP10-2004/NACE NO.1 (SA 2 1/2) AT THE TIME OF PAINT APPLICATION.

E) THE EXCEPTION TO NOTE "D" IS THE INTERIOR OF CABLE LOCKERS AND FUNNELS WHICH SHALL BE BLAST CLEANED TO WHITE METAL IN ACCORDANCE WITH SECTION SSPC-SP5-2004/NACE NO.1 (SA3).

F) DETAILED SURFACE PREPARATION SHALL BE ELABORATED UPON IN SHIPYARD STANDARDS.

1. PAINTS AND COATINGS SHALL BE IN ACCORDANCE WITH THE STANDARDS QUOTED AND SHALL BE OVER COATED AS SPECIFIED HEREIN AND/OR WITH MANUFACTURER’S INSTRUCTIONS. PAINT SCHEMES ARE IN ACCORDANCE WITH CFTO D-23-003-005/SF-002 "SPECIFICATION FOR MAINTENANCE PAINTING OF HMC SHIPS".

2. PRE TREATMENT, PRESERVATION AND PAINTING SHALL ONLY BE PREFORMED WITHIN THE RANGES OF TEMPERATURE AND HUMIDITY SPECIFIED IN THE MANUFACTURERS INSTRUCTIONS FOR EACH PRODUCT. NO WORK SHALL BE PREFORMED WHEN ADVERSE CLIMATIC OR DUSTY CONDITIONS PREVAIL.

8. UNDERWATER HULL

A) AT UNIT STAGE - BLAST TO STANDARD SSPS-SP-5-2004/NACE NO.1 (SA3) (MAINTAIN AT SA 2 1/2) AND CLEAN (QC INSPECTION) FOLLOWED BY APPLICATION OF TWO COATS OF VINYL ANTI-CORROSIVE PRIMER, (CODE C122) .

UNIT BUTTS REQUIRE TO BE TAPED OFF A DISTANCE OF 4" EITHER SIDE OF PROPOSED WELD. IF NOT TAPED, A DISTANCE OF 12" IS TO BE LEFT UNPAINTED.

B) AFTER ERECTION-AREA IN WAY OF ERECTION WELDS SHALL BE POWER TOOL CLEANED AND ONE COAT OF ZINC RICH EPOXY CODE C183 (50 TO 75 MICRONS) SHALL BE APPLIED AS A HOLDING PRIMER.

C) PRIOR TO LAUNCH, BURNED, DAMAGED AND ERECTION WELDS SHALL BE ABRASIVE BLASTED AND COATED WITH TWO COATS VINYL ANTI-CORROSIVE PRIMER, CODE C122.

THE BOTTOM THEN WILL BE HIGH PRESSURE WASHED, ALLOWED TO DRY, THEN THREE COATS OF ANTI-FOULANT, CODE C221 APPLIED AT 100-125 MICRONS PER COAT. FIRST COAT SHALL BE BLACK, SECOND COAT RED AND THIRD BLUE.

NOTE: AREAS BETWEEN BLOCKS SHOULD RECEIVE THREE COATS OF ANTI-FOULANT. THIS IS DONE IN PREPARATION FOR FLOATING THE SHIP.

D) DOCKING PRIOR TO TRIALS-BOTTOM TO BE HIGH PRESSURE WASHED AND TOUCHED UP, AREAS BETWEEN BLOCKS (BLOCKS LOCATION OF PREVIOUS DOCKING) SHALL BE GIVEN SPECIAL ATTENTION BY TOUCHING UP PREVOIUS COATINGS OF VINYL ANTI-CORROSIVE PRIMER BY APPLYING

TWO COATS OF CODE C122. THIS SHALL BE FOLLOWED BY THREE COATS OF ANTI-FOULANT, CODE C221 AT A DFT OF 100-125 MICRONS.

16. WOOD-VARNISHED LADDERS, BOOMS, STAFFS, SPURNWATER, BOARD (ASHORE & ON BOARD)

A) SURFACE PREPARATION: CLEANED AND SANDED, PRIMERS OR TIE COATS: SANDED BETWEEN COATS.

B) APPLY ONE SEALER COAT TO SPECIFICATION CODE C099 THINNED 20%, THEN WOOD FILLER SPECIFICATION CODE C103 SHALL BE APPLIED TO FILL ANY INPERFECTIONS.

C) APPLY FILLER SEALER COAT CODE C099, THINNED 10%.

D) APPLY TWO FINISH COATS OF CODE C099.

19. WOODEN RAMPS FOR HATCH COAMINGS.

A) SURFACE PREPARATION: CLEANED AND SANDED. PRIMERS OR TIE COATS. SANDED BETWEEN COATS. DO NOT SAND AFTER NON-SLIP AGGREGATE IS ADDED.

B) APPLY ONE SEALER COAT CODE 099 THINNED 20% THEN WOOD FILLER SPECIFICATION C103 SHALL BE APPLIED TO FILL ANY IMPERFECTIONS.

C) APPLY FILLER SEALER COAT CODE 099 THINNED 10%.

D) APPLY ONE COAT CODE C099, AND WHILE WET SPRINKLE ON THE NON-SLIP AGGREGATE TO PROVIDE A UNIFORM ROUGHENED TEXTURE.

E) APPLY TWO FINISH COATS CODE C099.

SHEET 3 OF 81

5. PERFORATED ALUMINUM SHEET USED IN CONNECTION WITH ACOUSTIC INSULATION SEE REFERENCE DRAWING NO. 1. (TOUCH UP IF REQUIRED PRIOR TO COMISSION WITH CODE C061 COLOUR AS REQUIRED)

Rev: C

6A6B2

1

2

1

B0

A2

A1

A1

A0

6C

6C

6C

6C

6C

6D

6D

6D

5D

Z1Z1

Z3

1

6D6D

5D

6E

Z2

A2

Z2

Z0

Z1

B2

2 6D

5D

6D

5D

5D

5D

6E

A2

A1

A2

A1 A3

5E6F

5F

5F

6F

6F 6F

Z2

Z1

Z0

1

2

6G

6F

6F

6G

5H

6H

6H

A2

A0

Z0 B0

B1

A0

A1

A2

A1

Z2

Z1A3

6J

6J

6J 5J

5J

5J

6J

6J

6K

6K

6K

6KA

B

Z2

Z1 6L6L

6L

6L

A

B

CDEFGHJKL

NO. 5 DECK

>

WTBWTB

WTB

WTBWTB

WTBWTBWTBWTB

5.5

12

20.525.5343943

47.5

52.5

58

KL

WTB

47.5

52.558

HJ

WTBWTB

3943

WTB

25.5

FG

WTB

34

E

WTB20.5

D C

WTB12

B

WTB

5.5

WTB

A

>

M

4MA

4MZ

6LZ1

6LZ2

A4B2Z2

A2A0

Z0

A1

A2

A0

A1Z

B A0 5H

4J4J4J

4J4J

4J

4J

4K

4K

4K4K

6L 4L

4L

6G

AZ 6A4B

4BA

B2

Z

B0

A0

A

4C4C

4C

4C

6D

4D

5E6FB0

C2

C1

Y2Z2B2

Z1

Z0

A0

4D4D

4D

4D4D5D

4D

4D

4E

NO. 4 DECK

NO. 3 DECK

Z0

Z2

3M

3M

A1

A0

A2

A4

3M

3M

3M

3M

Z1

Z0

A2

A4

A0Z0

A2

A4Z2

A0B0Z0

A2

A4

3J

3J

3J

3J

3K3K

3K

3K3K

3L3L3L

3L

3L

Z0

Z2

A1

Z3

B1

Z1

Z0

A2Z2

A1

A0

3G

3G

3H

3H

3H

3H

5H

3H

3H3H

3J

3JZ0

Z2

A2

C2Y2Z4

A1

B2

A2

A4B4

Z1

6F

3F

3F

3F

3F

3F3F3F

3G

6G

3G

3G

3G3G

AZA

B0

B0

Z0

Z2

B2

A0

Z0

A2

4B6A

3B3C

3C

4C

3C

3C

3C

3D

3D

3D

Z03D

Y0

Z2

B2

Z1

A1

B1

Y1

Y2

A0

A2

A3

A1

A4B2

3D

3D

5D

3E

3E

3E

5E3E

3E

3E

3E

3F

3F

6F

3F3F

>

A

WTB

B

WTB

5.5

C

WTB12WTB

20.5

D

WTB

25.5

EF

WTB

34

WTB

39

GH

WTB

43

K

WTB

47.5

J

52.5

L

58

M

Dwg No: HFX-D28-396-000-01 Previous DND No. 8355538 Date: 2004-09-02Title: Painting & Preservation ScheduleSHEET 4 OF 81

Rev: C

KL

WTB

47.5

52.558

HJ

WTBWTB

3943

WTB

25.5

FG

WTB

34

E

WTB20.5

D C

WTB12 B

WTB

5.5

WTB

A

>

M

NO. 2 DECK

Z3

Z1

Z0

B2Z2

A1B1Y1

Z3

Z1

A0

B0Z0

A2

B2

A4

Z2

A1B1Y1

Z3

Z1A0

Y0

Z0

Z2

Z4B2

A2

A1

Z1

Z0

A0

A2Z2

2J

2J

2J

2J2J

2K2K2K

2K

2K

2K

2K2K

2K

2K

2K

2K

2L2L2L

2L

2L2L

2L

2L

2L

2L2L

2L

2M

2M

2M

2M

2M2M

A3

A1

A0B0

A2

A4

2J

2J

2J2J

2J

2J

Z12H

Z22H

A3

A1

Z0

A2

2H

2H

5H

2H

2H

A1Z5

Z3

Z1B1

Z2

A4

B2

2G2G

2G

2G2G

2G

2G

2G

A1B1C1X1Y1Z3

A0

B0

A0

Z1

Z0

Z2

A2B2C2Y2Z4

A2

2F2F2F2F2F2F

2F

6F6F

2F

2F

2F

2F

2F

2F2F2F2F2F

6G

2G

A1

B1

A2

Z2

2E 3E

5E2E

2E

2E

A

B2

Z2

Y2

Z4

B0

Z0

B1

A0

A4

2D

2D

2D

2D

2D

2D

2D

2E

2E

B12D

B0

B2

Y2

Y4

Y0

B0

2C

2C

2C

2C

2C

4C

A12C

Z2C

A

Z1

Z2

Z2

A

A2

A0Z0

2A

2A

2A

2B

2B

2C

2C2B

MEZZ DECK

>

A

WTB

B

WTB

5.5

2BA Z

MA MAA

NO.1 DECK

>

12

D

20.525.5

EF

34

G

39

H

4347.5

JK

52.5

L

58

M

1M1M

1M 1M

1M

A0Z0

Z2 A2

A4

1H

1J

1H

1J1J

1J

1J1J

A1

0

A2

A3Z1

A1

A2Z2

1F

1F

1G

1G

5H

Z0

Z2

A

Z1

1D

1D

1D

1D

1D

1D

1D

1D

5D

1D

1D

1D1D

1E

1E

1E

1E

3E

1E

1E

1E

1EB

A2

C1

Y3

Z1

C0

Y1

Z0

C2

Y2

X2Z2

A0

A1

A3

A5

B1

B1

B0

B2

Z

B2

1DA

1F6F A

>

NO.01 DECK

01DA

B001D

C001D

Z201D

01DY1

Y301D

Z001D

A01E

B01E

01EB

A1G

Z201F

Z101F

A1G

Z201J

01JA2

1JA0

A101J

Z101J

01GZ0

Z101G

NO.01 DECKFUNNEL HOUSE TOP

12

D

20.5

E

25.5

F

34

G

39

H

43

J

47.5


Y42D

5DB2

SHEET 5 OF 81Rev: C

NO.5 DECK

NO.4 DECK

NO.3 DECK

NO.2 DECK

MEZZ. DECK

NO.1 DECK

FORWARD WEATHERDECK

DECKHOUSE SIDE & WEATHER DECKS

AFT WEATHERDECK

NO.02 DECK

>

BRIDGE TOP

B0

AZ

Z

A

Z01E

02E02F

02F

1G

01G

02J

DEFGHJ

HANGAR TOP FER INTAKE

PROFILE

FUNNEL G.T. FLAT


INTERIOR OF RUDDER TO BE TWICE FILLED & DRAINED WITH

C161 ALLOWING 24 HOURS BETWEEN COATS.

CENTRE BORE OF RUDDER STOCK TO BE TWICE FILLED & PUMPED

OUT WITH CODE C161 ALLOWING 24 HOURS BETWEEN COATS.

SHEET 6 OF 81Rev: C

>

TY

P

P&

S

BULWARK

FWD

SUPPORT FOR HF FAN ANTENNA

1500

RA

D

==

15.5 15 14.5C.L. OF SHIP

1500

RA

D

SUPPORT FOR HF FAN ANTENNA

==

FER CASING TOP

FR

28

FR

25.5

CA

SI

NG

EN

D

KN

UC

KL

E

CASING SIDE

1000

RA

D

1000

RA

D

OUTLINE OF WHIP ANTENNAS

CA

SI

NG

EN

D

DETAIL ’7-A’

KN

UC

KL

E

FER CASING TOP

TYP

CASING SIDE

FR

28FR

27

FR

25.5

2500

RA

D

2500

RA

D

OUTLINE OF WHIP ANTENNAS

N0 01 DECK

TOP OF

PYROTECHNICS LKR

=

= SEE INDIVDUAL PLAN VIEWS

FOR REQUIRED RADIUS

FR13.5

NAV SIDELIGHT DETAIL

FR13.25 FR13

PART PLAN VIEW SHOWING

RADHAZ MARKINGS IWO 18 FT WHIP ANTENNAS

STBD SIDE

PART PLAN VIEW OF 02 DECK

SHOWING RADHAZ MARKINGS IWO HF FAN ANTENNA BASE

PART PLAN VIEW SHOWING

RADHAZ MARKINGS IWO 35 FT WHIP ANTENNAS

PORT SIDE


STBD SIDE SHOWN LOOKING TO PORT

PORT SIDE SIMILAR OPPOSITE HAND

SEE "FOUNDATIONS & BACKGROUND" LISTING

COLOUR = RED

TYP.

COLOUR = WHITE

TYP.

COLOUR = WHITE

TYP.

COLOUR = RED

TYP.

SEE "RADHAZ MARKINGS" LISTING

COLOUR = WHITE

TYP.

COLOUR = WHITE

TYP. DETAIL ’7-A’

DETAIL ’7-A’

DETAIL ’7-A’

DETAIL ’7-A’

COLOUR = RED

TYP.


COLOUR = RED

TYP.COLOUR = WHITE

TYP.

COLOUR = WHITE

TYP.


COLOUR = WHITE

TYP.

COLOUR = RED

TYP.


NO. 1 DECK

SEE "DECK MARKINGS (VERTREP)" LISTING

3 21

0

5750

140

00

14001

91

4

1015

1525 1525

1525

1525

305

305

30

5

30

5

325

101

6250

900

1000

127

102

127

76

25

SHEET 7 OF 81

SEE "WOODEN SCREENS" LISTING

BLACK

BLACK

BLACK

Rev: C

47 46 45>

PART PLAN VIEW OF HANGAR TOP

I.W.O. C.I.W.S.

EXHAUST HAZARD ZONE

DO NOT STAND IN

DANGER

DETAIL ’8-B’

WARNING MARKINGS


DANGER

ELEVATE WITHOUT WARNING

GUN MAY TRAIN AND

DETAIL ’8-A’

WARNING MARKINGS

((

((

((

( (

10 98 7 6 5 4

45̂ T

YP.

35̂ TYP.

*

* -DETERMINE AT SHIP

45̂ T

YP.

35̂ T

YP.

SHIPS SIDE 01 DECK

PART PLAN VIEW OF NO. 01 DECK

I.W.O. CHAFF LAUNCHERS STBD SIDE

SHIPS SIDE 01 DECK


I.W.O. CHAFF LAUNCHERS PORT SIDE

35̂ T

YP.

45̂ T

YP.

35̂ T

YP.

45̂ T

YP.

-DETERMINE AT SHIP*

*


I.W.O. 57MM GUN

SEE "SAFETY/WARNING MARKINGS" LISTING


NOTE: MARKINGS TO BE CARRIED OVER TOP OF ANY

PLATFORMS I.W.O. HAZARD AREA.

SEE "SAFEFTY/WARNING MARKINGS" LISTING

NOTE: MARKINGS TO BE CARRIED OVER TOP OF ANY

PLATFORMS I.W.O. HAZARD AREA.


3175

R

125 AND PARALLEL6 TYP.

60 TYP.

50

TY

P.

60

TY

P.

6 TYP.60 TYP.

50

TY

P.

50

TY

P.

50

60

TY

P.

300 AND PARALLEL

6 TYP.

60 TYP.

30 TYP.

50 T

YP.

50 T

YP. 60 T

YP.

60 TYP. 50 T

YP.

60 T

YP.

10 TYP.40 TYP.

6 TYP.

100

TYP.

2000 TYP.

1000

500 TYP.

100

TYP.

4782

R

2000 TYP.

500 TYP.

100 T

YP.

100 TYP.

100 T

HK.

100

TYP.

SHEET 8 OF 81Rev: C

WARNING MARKINGS

SEE DETAIL ’8-A’

COLOUR = RED

WARNING MARKINGS


COLOUR = RED

NO. 01 DECK

NO. 01 DECK OR

HANGAR TOP

COLOUR = RED

WARNING MARKINGS

SEE DETAIL ’8-B’

COLOUR = RED

WARNING MARKINGS


COLOUR = RED

COLOUR = RED

COLOUR = RED

COLOUR = RED

COLOUR = RED

COLOUR = RED

COLOUR = RED

COLOUR = RED

WARNING MARKINGS


COLOUR = RED

WARNING MARKINGS


COLOUR = RED

WARNING MARKINGS


COLOUR = RED

WARNING MARKINGS


COLOUR = RED

WARNING MARKINGS


COLOUR = RED.

POSITIONED MIDWAY

BETWEEN CAPSTAN &

BOLLARD, P & S.

WARNING MARKINGS


COLOUR = RED

COLOUR = RED

VL

KLM

4748495051525354555657585960616263>

38

TH

KNO 1 WEATHERDECK

DECK MARKINGS

HULL NO. SHIP NAME (HMCS) SHIP/LETTER

DESIGNATOR

FFH330

FFH331

FFH332

FFH333

FFH334

FFH335

FFH336

FFH337

FFH338

FFH339

FFH340

FFH341

TORONTO

CALGARY

MONTREAL

WINNIPEG

VANCOUVER

VILLE DE QUEBEC

REGINA

FREDERICTON

CHARLOTTETOWN

ST. JOHN’S

OTTAWA

HX

VR

VC

TO

RA

CY

ML

FN

WG

CH

SJ

OA

FLIGHT DECK DESIGNATORS

SIZE AND LOCATION OF LETTER DESIGNATORS SAME

AS SHOWN ON PLAN VIEW OF NO 1 WEATHERDECK.


SEE "FLIGHT DECK MARKINGS" LISTING

TY

P.

HANGAR TOP

PAINT MARKINGS TO BE EXTENDED FROM HANGARTOP/END DOWN HANGAR END INCLUDING HANGAR DOORTO ALIGN WITH SIMILAR MARKINGS ON 1 DECK

SEE HANGAR FACE AND TOP MARKINGS LISTING

COLOUR = YELLOW

1524550

1219

900

1219

900

305

1524550

305

305

27

43

2286

203(

TY

P)

610

45

7

127

12

7

91

4

305305

30

53

05

101

305

305

610

2667

8534 305

305

61

0

2667

1829

14326

425

102

3658

102

SHEET 9 OF 81Rev: C

SEE TABLE FOR LIST OF

SHIP/LETTER DESIGNATORS

2345678

SEAT FOR

57mm GUN

FR.

8F

R.

8

NOTES:

1) NON-SKID PAINT IS TO BE APPLIED TO ALL TRAFFIC AREAS INTERNALLY AND

EXTERNALLY AS REQUIRED WITHIN THIS DOCUMENT.

3) NON-SKID DECK PAINT SHALL NORMALLY BE TERMINATED APPROX. 100mm FROM EQUIPMENT, BULKHEADS, ETC.

THIS MAY BE INCREASED OR DECREASED AS REQUIRED IN WAY OF OBSTRUCTIONS OR WHERE IT IS OBVIOUSLY

NOT REQUIRED. IN WAY OF DOORS IT SHALL TERMINATE APPROX. 50mm FROM THE BULKHEAD.

2) NON-SKID PAINT IS NOT TO BE APPLIED TO INACCESSIBLE OR NON TRAFFIC AREAS, FOR EXAMPLE:

WITHIN MODULAR SHELVING UNITS

WITHIN EQUIPMENT FOUNDATIONS

UNDER FIXED DESKS OR WORKBENCHES

ON TOP OF MANHOLES OR HATCHES

UNDER NON TRAFFIC AREAS OF INCLINED STARWAYS

UP

>

>

NON-SKID PAINT LAYOUT

SAMPLE COMPARTMENT

NON-SKID PAINT LAYOUT

SAMPLE WEATHERDECK

4) ONLY APPLY NON-SKID DECK PAINT TO TRAFFIC AREAS 750mm OR GREATER.


750

100

50

10

0

100

100

150

300

100

100

100

150

100

100

SHEET 10 OF 81Rev: C

PLENUMS

ROLLER FAIRLEAD

(P&S)

CARTRIDGE CASE

SAVEALL ASSEMBLY

BREAKWATER

MOORING/TOWING

WINDLASS

ANCHOR

WINDLASS/CAPSTAN

CHAIN PIPE

DECK BOLSTER

(P&S)

FIXED DESK AND CABINET

WORKBENCH

MANHOLE

MANHOLE

FOUNDATION

FOUNDATION

MODULAR SHELVES

SHEET 11 OF 81 Date: 2004-09-02 Rev: C

Quanity Litres Specification Description Dry Film Thickness Per Coat Colour Thinner Required NSCM No. Remarks

D-23-003-005/SF-002 Min HR Max

8237 C212 PRIMER, MARINE, FOR STEELAS PER MANUFACTURER RECOMMENDATION

AS PER MANUFACTURER RECOMMENDATION

7728 C061 ENAMEL, ALKYD MARINE, EXTERIORAS PER MANUFACTURER RECOMMENDATION WHITE 27925


945 C061 ENAMEL, ALKYD MARINE, EXTERIORAS PER MANUFACTURER RECOMMENDATION GREY 27880








113 C061 ENAMEL, ALKYD MARINE, EXTERIORAS PER MANUFACTURER RECOMMENDATION GREEN 24585












4 C061 ENAMEL, ALKYD MARINE, EXTERIORAS PER MANUFACTURER RECOMMENDATION RED 11310


21 C061 ENAMEL, ALKYD MARINE, EXTERIORAS PER MANUFACTURER RECOMMENDATION RED 11350


20 C061 ENAMEL, ALKYD MARINE, EXTERIORAS PER MANUFACTURER RECOMMENDATION BLACK 17038






22 C061 ENAMEL, ALKYD MARINE, EXTERIORAS PER MANUFACTURER RECOMMENDATION WHITE 17925


4 C061 ENAMEL, ALKYD MARINE, EXTERIORAS PER MANUFACTURER RECOMMENDATION ORANGE 12473


5 C061 ENAMEL, ALKYD MARINE, EXTERIORAS PER MANUFACTURER RECOMMENDATION BLUE 15052


4 C061 ENAMEL, ALKYD MARINE, EXTERIORAS PER MANUFACTURER RECOMMENDATION YELLOW 13538


722 C076 ENAMEL, HEAT RESISTANT, EXTERIORAS PER MANUFACTURER RECOMMENDATION GREY 16480


210 C076 ENAMEL, HEAT RESISTANT, EXTERIORAS PER MANUFACTURER RECOMMENDATION BLACK 17038


20 ENAMEL, ALKYD, AIR DRY SEMI-GLOSS, TYPE IAS PER MANUFACTURER RECOMMENDATION

AS PER MANUFACTURER RECOMMENDATION COLOURS TO BE DETERMINED

45 C0100 PAINT, INTERIOR, LATEX TYPE, SATIN FINISHAS PER MANUFACTURER RECOMMENDATION


6823 C213COATING COMPOUND, VINYL PRETREATMENT FOR METALS (VINYL WASH PRIMER)



3280 C122 PRIMER, VINYL, ANTI-CORROSIVE, TYPE IIIAS PER MANUFACTURER RECOMMENDATION


180 C221 COATING, ANTIFOULINGAS PER MANUFACTURER RECOMMENDATION BLACK

AS PER MANUFACTURER RECOMMENDATION REFER TO D-23-003-005/SF-002 CODE 221 FOR COLORS

Overcoat Time

Dwg No: HFX-D28-396-000-01 Previous DND No. 8355538Title: Painting & Preservation Schedule



D-23-003-005/SF-002 Min HR Max

Overcoat Time


2004 C221 COATING, ANTIFOULINGAS PER MANUFACTURER RECOMMENDATION PLUM


939 C221 COATING, ANTIFOULINGAS PER MANUFACTURER RECOMMENDATION PINK


90 C212 PRIMER, ZINC CHORMATE, LOW MOISTURE SENSITIVITYAS PER MANUFACTURER RECOMMENDATION


35 C143 PAINT, ALUMINUM, HEAT RESISTANT, SILICONE ALKYDAS PER MANUFACTURER RECOMMENDATION


160 C146 COATING, EPOXY INTERIOR, COLD CURED, GLOSS, TYPE IIAS PER MANUFACTURER RECOMMENDATION WHITE


30 C146 COATING, EPOXY INTERIOR, COLD CURED, GLOSS, TYPE IIAS PER MANUFACTURER RECOMMENDATION GREY 27880


7830 ASTERPIOL "P" J8 CODE 060008AS PER MANUFACTURER RECOMMENDATION


160 C165PRIMER, COATING, EPOXY, COLD CURING, FOR FERROUS METALS, TYPE I

AS PER MANUFACTURER RECOMMENDATION RED


4315 C171 COATING COMPOUND, INORGANIC ZINC, TYPE I, CLASS AAS PER MANUFACTURER RECOMMENDATION


1979 C183 PRIMER, COATING, ZINC RICH EPOXYAS PER MANUFACTURER RECOMMENDATION


702 C200 DECK COATING, NON-SLIP, POLYURETHANEAS PER MANUFACTURER RECOMMENDATION GREEN 34090


3453 C200 DECK COATING, NON-SLIP, POLYURETHANEAS PER MANUFACTURER RECOMMENDATION GREY 36076


2400 COATING, INTERGARD, EXB 000/EXA 008AS PER MANUFACTURER RECOMMENDATION WHITE


2300 COATING, INTERGARD, EXB 000/EXA 008AS PER MANUFACTURER RECOMMENDATION GREY


4457 C207 COATING, TWO COMPONENT, EPOXY OR MODIFIED EPOXYAS PER MANUFACTURER RECOMMENDATION BUFF


4452 C207 COATING, TWO COMPONENT, EPOXY OR MODIFIED EPOXYAS PER MANUFACTURER RECOMMENDATION OFF-WHITE


2320 C072 COATING. COMPOUND, LAGGING, FIRE RESISTANT, TYPE IAS PER MANUFACTURER RECOMMENDATION


26 CU 471068 COATING, INTERLUX TBTFAS PER MANUFACTURER RECOMMENDATION WHITE


20 C050 TECTYL 502CAS PER MANUFACTURER RECOMMENDATION


40 5769 RUST-O-CRYLICAS PER MANUFACTURER RECOMMENDATION

AS PER MANUFACTURER RECOMMENDATION RUST OLEUM CORPORATION, SEE NOTE 4

28 C099 VARNISH, PHENOLIC RESIN, EXTERIOR MARINEAS PER MANUFACTURER RECOMMENDATION

AS PER MANUFACTURER RECOMMENDATION SHT 3, NOTE 18

5KG C103 FILLER, WOOD PASTEAS PER MANUFACTURER RECOMMENDATION

AS PER MANUFACTURER RECOMMENDATION SHT 3, NOTE 18

10 PRIMER, FIBREGLASS, INTERLUX 200AS PER MANUFACTURER RECOMMENDATION


17 C207 COATING, EPOXY, HIGH SOLIDAS PER MANUFACTURER RECOMMENDATION


24 COATING, MODIFIED EPOXY, TIECOAT, INTERGARD 263AS PER MANUFACTURER RECOMMENDATION


20 5269 RUST-O-CRYLICAS PER MANUFACTURER RECOMMENDATION RED

AS PER MANUFACTURER RECOMMENDATION RUST OLEUM CORPORATION SEE NOTE 5

10 COMM PAINT, ALKYD FLATAS PER MANUFACTURER RECOMMENDATION BLACK


20 C177 COATING PLASTIC POLYURETHANE GLOSSAS PER MANUFACTURER RECOMMENDATION YELLOW 13655




D-23-003-005/SF-002 Min HR Max

Overcoat Time


30 C177 COATING PLASTIC POLYURETHANE GLOSSAS PER MANUFACTURER RECOMMENDATION WHITE 17925


25 C177 COATING PLASTIC POLYURETHANE GLOSSAS PER MANUFACTURER RECOMMENDATION RED


20 C177 COATING PLASTIC POLYURETHANE GLOSSAS PER MANUFACTURER RECOMMENDATION BLACK


4 AGGREGATE, NON-SLIP, GRANULAR, ORG. ABRSVAS PER MANUFACTURER RECOMMENDATION

AS PER MANUFACTURER RECOMMENDATION INTERNATIONAL PAINT (CANADA) LTD.

5 PRIMER, INTERGARD 251AS PER MANUFACTURER RECOMMENDATION


5 FINISH COAT, INTERGARD 740AS PER MANUFACTURER RECOMMENDATION GREY 16480


20 PRIMER, CEILCOTE 370 HTAS PER MANUFACTURER RECOMMENDATION ORANGE

AS PER MANUFACTURER RECOMMENDATION SEE NOTE 6

25 CEILCOTE 322 FLAKELINEAS PER MANUFACTURER RECOMMENDATION TAN


25 CEILCOTE 322 FLAKELINEAS PER MANUFACTURER RECOMMENDATION WHITE


19 ACRYLIC COATING WHITEAS PER MANUFACTURER RECOMMENDATION MFG PART # 40-0200 SERIES

NOTES:1. "FILL & DRAIN" PRODUCT. 7830 L REQUIRED PER LEAD SHIP (HULL FFH330-FFH332), FOLLOWSHIPS REQUIRE 300L FOR TOP UP2. OVERCOAT TIME - 10 DAYS-EXTERIOR, INDEFINITE-INTERIOR3. OVERCOAT TIME - 3 MONTHS-EXTERIOR, 12 MONTHS-INTERIOR4. HULL FFH330-FFH332 ONLY5. HULL FFH333-FFH341 ONLY6. HULL FFH332-FFH341 ONLY

First Coat µm

Second Coat µm µm Spec First Coat

µmSecond Coat µm

Third Coat µm

Forth Coat µm

Fifth Coat µm Spec First Coat

µmSecond Coat µm

Third Coat µm

KEEL TO BOTTOM OF BOOT TOP AREA EXCLUDING SONAR DOME FAIRING (FIRBREGLASS) & SHAFTS (FIBREGLASS SHEATHED) SEE GENERAL NOTE NO.8

C221 100-125


C122 75-100 75-100 C221 100-125 SEE NOTE "A", "B" AND "D"


C221 100-125

BOOT TOPPING C221 100-125

BOOT TOPPING C122 75-100 75-100 C221 100-125

BOOT TOPPING C221 100-125

SONAR DOME FAIRING (FIRBREGLASS) & SHAFTS (FIBREGLASS SHEATHED) SEE GENERAL NOTE NO.17

INTERLUX 200 5 C221 100-125 AS PER D-23-003-005/SF-002


C207 125 C221 100-125 AS PER D-23-003-005/SF-002


C207 125 C221 100-125 AS PER D-23-003-005/SF-002

SHIPS BOTTOM SEARCH GRID D-23-003-005/SF-002 100-125 100-125 WHITE SEE NOTE "C"

DIELECTRIC SHIELD INSTALLATION SEE NOTE "B"

NOTE "A"

NOTE "B"

NOTE "C" FOR EXTENT OF SHIPS BOTTOM SEARCH GRID SEE DWG NO. 01-8315-6-2020. (APPLY CAPASTIC AND TREAT SUBSTRATE 1AW D-23-003-005/SF-002)

NOTE "D" THE SONAR DOME MOUNTING RING AND SOLE PLATE INCLUDING THE BOLT HOLE INTERIORS AND THE MACHINED SURFACE ARE TO RECEIVE THE FULL UNDERWATER COATING SYSTEM, LESS THE THIRD COAT OF ANTI-FOULING PAINT.

Item Description

UNDERWATER HULL CONSISTS OF SHAFT "A" BRACKETS, RUDDER, SEABOXES, SEA INLETS, DISCHARGES, GRATINGS, EXTERIOR OF BILGE KEELS AND PART OF SONAR TRUNK BELOW WT FLAT APPROX 1600mm ABOVE BASE LINE

Primer Finisher

SANDBLAST 4267mm DIA CIRCULAR AREA (SEE SKETCH) TO WHITE METAL AS PER SSPC-SP5 2004/NACE NO.1 (SA3) OF SPECIFICATION ANSI A159.1-1972. TREAT SUBSTRATE

Colour Remarks

Title: Painting & Preservation Schedule Dwg No: HFX-D28-396-000-01 Previous DND No. 8355538SHEET 14 OF 81

Rev: CDate: 2004-09-02

SHEET 15 OF 81Title: Painting & Preservation Schedule

VOID 6A 57.1 ALL INTERIOR SURFACES

TWICE FILLED AND DRAINED WITH ASTERPIOL 'P' J8 ALLOWING 24 HOURS BETWEEN COATS

SALTWATER BALLAST/STANDBY DFO TANK #1 6B 104.3 ALL INTERIOR SURFACES C193 125 GREY

SALTWATER BALLAST/STANDBY DFO TANK #1 6B 104.3 ALL INTERIOR SURFACES C193 125 WHITE

DFO TANK NO.1 6C1 116.0 ALL INTERIOR SURFACES C193 125 GREY

DFO TANK NO.1 6C1 116.0 ALL INTERIOR SURFACES C193 125 WHITE

DFO TANK NO.2 6C2 116.0 ALL INTERIOR SURFACES C193 125 GREY

DFO TANK NO.2 6C2 116.0 ALL INTERIOR SURFACES C193 125 WHITE

SPEED LOG TRANSDUCER SPACE 6CB0 20.8 ALL INTERIOR SURFACES C207 See

Remarks BUFF D.F.T. PER COAT IS 125-150 MICRONS

SPEED LOG TRANSDUCER SPACE 6CB0 20.8 ALL INTERIOR SURFACES C207 See

Remarks OFF-WHITE D.F.T. PER COAT IS 125-150 MICRONS

SONAR TRUNK 6DA0 5.7 ST DECK C413 Manufacturer SEE OTHERS FOR DECK COVERING

SONAR TRUNK 6DA0 5.7 ST DECK C413 Manufacturer

SONAR TRUNK 6DA0 5.7 ST DECK C200 750-1000 36076 4th COAT OF FINISHER APPLIED THE SAME AS 3rd COAT

SONAR TRUNK 6DA0 5.7 DECKHEAD C212 40 40 RED SEE OTHERS FOR INSULATION.SONAR TRUNK 6DA0 5.7 DECKHEAD C061 40 27925 SEE OTHERS FOR INSULATION.

SONAR TRUNK 6DA0 8.6 FORWARD NOTE 4 C212 40 40 REDSEE OTHERS FOR INSULATION. 4th COAT OF FINISHER APPLIED THE SAME AS 3rd COAT.

SONAR TRUNK 6DA0 8.6 FORWARD NOTE 4 C061 40 27925SEE OTHERS FOR INSULATION. 4th COAT OF FINISHER APPLIED THE SAME AS 3rd COAT.

SONAR TRUNK 6DA0 8.6 AFT NOTE 4 C212 40 40 RED SEE OTHERS FOR INSULATION.

SONAR TRUNK 6DA0 8.6 AFT NOTE 4 C061 40 27925 SEE OTHERS FOR INSULATION.

SONAR TRUNK 6DA0 9.4 PORT NOTE 4 C212 40 40 RED SEE OTHERS FOR INSULATION.

SONAR TRUNK 6DA0 9.4 PORT NOTE 4 C061 40 27925 SEE OTHERS FOR INSULATION.

SONAR TRUNK 6DA0 9.4 STBD NOTE 4 C212 40 40 RED SEE OTHERS FOR INSULATION.

SONAR TRUNK 6DA0 9.4 STBD NOTE 4 C061 40 27925 SEE OTHERS FOR INSULATION.

SONAR TRUNK 6DA0 5.7 OTHERS C061 40 40 27925 DECK COVERING

SONAR TRUNK 6DA0 5.7 OTHERS C061 40 40 27925 INSULATION

DFO TANK NO.3 6DA1 71.4 ALL INTERIOR SURFACES C193 125 BUFF

DFO TANK NO.3 6DA1 71.4 ALL INTERIOR SURFACES C193 125 WHITE

DFO TANK NO.4 6DA2 71.4 ALL INTERIOR SURFACES C193 125 BUFF

Date: 2004-09-02Previous DND No. 8355538Dwg No: HFX-D28-396-000-01

Primer

DCZ Area M2

Surface1st Coat

µm

Inorganic Zinc Primer C171Compartment

Name

Remarks

Rev: C

2nd Coat µm Spec 1st Coat

µm2nd Coat

µm

Deck Covering/ Insulation

Finisher

Ref Note ColourSpec 2nd Coat

µm3rd Coat

µm1st Coat

µm

SHEET 16 OF 81Title: Painting & Preservation Schedule Date: 2004-09-02Previous DND No. 8355538Dwg No: HFX-D28-396-000-01

Primer

DCZ Area M2

Surface1st Coat

µm


Name

Remarks

Rev: C


µm2nd Coat

µm


Finisher


µm3rd Coat

µm1st Coat

µm

DFO TANK NO.4 6DA2 71.4 ALL INTERIOR SURFACES C193 125 125 FIRST COAT OFF-WHITE, SECOND

COAT WHITE

DFO TANK NO.5 6DZ1 212.2 ALL INTERIOR SURFACES C193 125 125 FIRST COAT OFF-WHITE, SECOND

COAT WHITE


COAT WHITE


COAT WHITE


COAT WHITE

DFO TANK NO.7 6E1 193.8 ALL INTERIOR SURFACES C193 125 125 FIRST COAT OFF-WHITE, SECOND

COAT WHITE


COAT WHITE


COAT WHITE


COAT WHITE

FER INTAKES(3 DECK TO 1 DECK) 6F 24.9 DECKHEAD (UNDER 1 DECK) 76 C045 40 C076 30 30 26480

FER INTAKES(3 DECK TO 1 DECK) 6F 37.4 FORWARD 76 INSULATION NOTE 5 26480FER INTAKES(3 DECK TO 1 DECK) 6F 37.4 AFT 76 INSULATION NOTE 5 26480FER INTAKES(3 DECK TO 1 DECK) 6F 32.2 PORT 76 INSULATION NOTE 5 26480FER INTAKES(3 DECK TO 1 DECK) 6F 32.2 STBD 76 INSULATION NOTE 5 26480

FER UPTAKES(3 DECK TO G.T. FLAT 13200 ABL) 6F 10.2 ST DECK (3 DECK) 76 C045 40 C076 30 30 26480



FER UPTAKES(3 DECK TO G.T. FLAT 13200 ABL) 6F 34.1DECKHEAD

(UNDER G.T. FLAT)

76 INSULATION C076 30 30 26480

FER UPTAKES(3 DECK TO G.T. FLAT 13200 ABL) 6F 20.2 DECKHEAD (UNDER 1 DECK) 76 INSULATION C076 30 30 26480

FER UPTAKES(3 DECK TO G.T. FLAT 13200 ABL) 6F 11.0 DECKHEAD (UNDER 2 DECK) 76 INSULATION C076 30 30 26480

FER UPTAKES(3 DECK TO G.T. FLAT 13200 ABL) 6F 49.9 FORWARD 76 INSULATION NOTE 5 26480

FER UPTAKES(3 DECK TO G.T. FLAT 13200 ABL) 6F 89.1 AFT 76 INSULATION NOTE 5 26480

FER UPTAKES(3 DECK TO G.T. FLAT 13200 ABL) 6F 34.1 PORT 76 INSULATION NOTE 5 26480

FER UPTAKES(3 DECK TO G.T. FLAT 13200 ABL) 6F 34.1 STBD 76 INSULATION NOTE 5 26480

FORWARD ENGINE ROOM 6F 239.9 ST DECK C207 See Remarks

BUFF/WHITE OR OFF WHITE

UP TO NO.19 SHELL LONG'L. D.F.T. PER COAT IS 125-150 MICRONS. REDUCE D.F.T. BEHIND FLUSH MOUNTED INSULATION TO 2 COATS 75-100 MICRONS


Primer

DCZ Area M2

Surface1st Coat

µm


Name

Remarks

Rev: C


µm2nd Coat

µm


Finisher


µm3rd Coat

µm1st Coat

µm

FORWARD ENGINE ROOM 6F 239.9 ST DECK C207 See Remarks OFF-WHITE


FORWARD ENGINE ROOM 6F 253.0 DECKHEAD C212 36 36 INSULATION C061 30 30 WHITE 27925FORWARD ENGINE ROOM 6F 72.2 FORWARD C212 36 36 INSULATION NOTE 5 WHITE 27925FORWARD ENGINE ROOM 6F 72.2 AFT C212 36 36 INSULATION NOTE 5 WHITE 27925FORWARD ENGINE ROOM 6F 121.5 PORT C212 36 36 INSULATION NOTE 5 WHITE 27925FORWARD ENGINE ROOM 6F 121.5 STBD C212 36 36 INSULATION NOTE 5 WHITE 27925FORWARD ENGINE ROOM 6F 369.0 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480 ABOVE BOOT TOP

FORWARD ENGINE ROOM 6F N/A OTHERS C207 See Remarks BUFF DECK ENCLOSED BY SEATS. D.F.T.

PER COAT IS 125-150 MICRONS

FORWARD ENGINE ROOM 6F N/A OTHERS C207 See Remarks OFF-WHITE DECK ENCLOSED BY SEATS. D.F.T.


FORWARD ENGINE ROOM 6F N/A OTHERS C212 36 36 C061 30 30 WHITE 27925 DECKHEAD STIFFENING CLEAR OF INSULATION

CBRN CONTAMINATION COLLECTION TANK 6FA1 19.8 ALL INTERIOR SURFACES C207 See


CBRN CONTAMINATION COLLECTION TANK 6FA1 19.8 ALL INTERIOR SURFACES C207 See

Remarks OFF-WHITE D.F.T. PER COAT IS 125-150 MICRONS

OIL WATER COLLECTION TANK 6FA2 49.4 ALL INTERIOR SURFACES C193 125 GREY

OIL WATER COLLECTION TANK 6FA2 49.4 ALL INTERIOR SURFACES C193 125 WHITE

RECOVERED OIL TANK 6FA3 32.2 ALL INTERIOR SURFACES C193 125 GREY

RECOVERED OIL TANK 6FA3 32.2 ALL INTERIOR SURFACES C193 125 WHITE

LUBE OIL STORAGE TANK NO.1 6FZ1 29.9 ALL INTERIOR SURFACES C193 125 GREY

LUBE OIL STORAGE TANK NO.1 6FZ1 29.9 ALL INTERIOR SURFACES C193 125 WHITE

LUBE OIL STORAGE TANK NO.2 6FZ2 29.9 ALL INTERIOR SURFACES C193 125 GREY

LUBE OIL STORAGE TANK NO.2 6FZ2 29.9 ALL INTERIOR SURFACES C193 125 WHITE

AER CASING(3 DECK TO 1 DECK) 6G 3.5 ST DECK (3 DECK) 76 C045 40 C076 30 30 GREY 26480

AER CASING(3 DECK TO 1 DECK) 6G 8.4 ST DECK (2 DECK) 76 C045 40 C076 30 30 GREY 26480

AER CASING(3 DECK TO 1 DECK) 6G 16.9 DECKHEAD (UNDER 1 DECK) 76 INSULATION C076 30 30 GREY 26480

AER CASING(3 DECK TO 1 DECK) 6G 9.1 DECKHEAD (UNDER 2 DECK) 76 INSULATION C076 30 30 GREY 26480

AER CASING(3 DECK TO 1 DECK) 6G 37.0 FORWARD 76 INSULATION NOTE 5 GREY 26480AER CASING(3 DECK TO 1 DECK) 6G 41.9 AFT 76 INSULATION NOTE 5 GREY 26480AER CASING(3 DECK TO 1 DECK) 6G 32.0 PORT 76 INSULATION NOTE 5 GREY 26480AER CASING(3 DECK TO 1 DECK) 6G 32.0 STBD 76 INSULATION NOTE 5 GREY 26480


Primer

DCZ Area M2

Surface1st Coat

µm


Name

Remarks

Rev: C


µm2nd Coat

µm


Finisher


µm3rd Coat

µm1st Coat

µm

AFT ENGINE ROOM 6G 141.9 ST DECK C207 See Remarks BUFF


AFT ENGINE ROOM 6G 141.9 ST DECK C207 See Remarks OFF-WHITE


AFT ENGINE ROOM 6G 174.2 DECKHEAD C212 36 36 INSULATION C061 30 30 WHITE 27925AFT ENGINE ROOM 6G 83.0 FORWARD C212 36 36 INSULATION NOTE 5 WHITE 27925AFT ENGINE ROOM 6G 83.0 AFT C212 36 36 INSULATION NOTE 5 WHITE 27925AFT ENGINE ROOM 6G 58.9 PORT C212 36 36 INSULATION NOTE 5 WHITE 27925AFT ENGINE ROOM 6G 58.9 STBD C212 36 36 INSULATION NOTE 5 WHITE 27925AFT ENGINE ROOM 6G 220.6 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480 ABOVE BOOT TOP

AFT ENGINE ROOM 6G N/A OTHERS C207 See Remarks BUFF DECK ENCLOSED BY SEATS. D.F.T.


AFT ENGINE ROOM 6G N/A OTHERS C207 See Remarks OFF-WHITE DECK ENCLOSED BY SEATS. D.F.T.


AFT ENGINE ROOM 6G N/A OTHERS C212 36 36 C061 30 30 WHITE 27925 DECKHEAD STIFFENING CLEAR OF INSULATION

LUBE OIL DRAIN TANK 6GZ0 21.0 ALL INTERIOR SURFACES C193 125 GREY

LUBE OIL DRAIN TANK 6GZ0 21.0 ALL INTERIOR SURFACES C193 125 WHITE

DFO SETTLING TANK NO.1 6H1 100.3 ALL INTERIOR SURFACES C193 125 GREY

DFO SETTLING TANK NO.1 6H1 100.3 ALL INTERIOR SURFACES C193 125 WHITE

DFO SETTLING TANK NO.2 6H2 100.3 ALL INTERIOR SURFACES C193 125 GREY

DFO SETTLING TANK NO.2 6H2 100.3 ALL INTERIOR SURFACES C193 125 WHITE

JP5 TANK NO.1 6KA1 127.9 ALL INTERIOR SURFACES C193 125 GREY

JP5 TANK NO.1 6KA1 127.9 ALL INTERIOR SURFACES C193 125 WHITE

JP5 TANK NO.2 6KA2 127.9 ALL INTERIOR SURFACES C193 125 GREY

JP5 TANK NO.2 6KA2 127.9 ALL INTERIOR SURFACES C193 125 WHITE

DFO TANK NO.11 6KZ1 227.8 ALL INTERIOR SURFACES C193 125 GREY

DFO TANK NO.11 6KZ1 227.8 ALL INTERIOR SURFACES C193 125 WHITE

DFO TANK NO.10 6KZ2 227.8 ALL INTERIOR SURFACES C193 125 GREY

DFO TANK NO.10 6KZ2 227.8 ALL INTERIOR SURFACES C193 125 WHITE

SALTWATER BALLAST TANK NO. 2/STANDBY DFO TANK NO. 2 6LB 217.1 ALL INTERIOR

SURFACES C193 125 GREY


Primer

DCZ Area M2

Surface1st Coat

µm


Name

Remarks

Rev: C


µm2nd Coat

µm


Finisher


µm3rd Coat

µm1st Coat

µm

SALTWATER BALLAST TANK NO. 2/STANDBY DFO TANK NO. 2 6LB 217.1 ALL INTERIOR

SURFACES C193 125 WHITE

SALTWATER BALLAST TANK NO. 2/STANDBY DFO TANK NO. 2 6LB 62.0 SHELL EXT C411 30 30 30 GREY 26480 ABOVE BOOT TOP

SALTWATER BALLAST TANK NO. 3/STANDBY DFO TANK NO. 3 6LZ1 153.6 ALL INTERIOR




SALTWATER BALLAST TANK NO. 3/STANDBY DFO TANK NO. 3 6LZ1 15.2 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480 ABOVE BOOT TOP





SALTWATER BALLAST TANK NO. 4/STANDBY DFO TANK NO. 4 6LZ2 15.2 SHELL EXT 76 C411 30 30 30 GREY 26480 ABOVE BOOT TOP

COFFERDAM/VOID SPACE 5C 149.0 INTERIOR SURFACES C207 See

Remarks BUFF D.F.T PER COAT IS 125-150 MICRONS

COFFERDAM/VOID SPACE 5C 149.0 INTERIOR SURFACES C207 See

Remarks OFF-WHITE D.F.T PER COAT IS 125-150 MICRONS

DRY PROVISION STORE 5DA1 47.3 ST DECK C413 Manufacturer

DRY PROVISION STORE 5DA1 47.3 ST DECK C413 Manufacturer

DRY PROVISION STORE 5DA1 47.3 ST DECK C404 40 16076 4th COAT OF FINISHER APPLIED THE SAME AS 3rd COAT

DRY PROVISION STORE 5DA1 55.4 DECKHEAD NOTE 4 C212 40 40 RED PART INSULATED.

DRY PROVISION STORE 5DA1 55.4 DECKHEAD NOTE 4 C061 40 27925PART INSULATED. 4th COAT OF FINISHER APPLIED THE SAME AS 3rd COAT

DRY PROVISION STORE 5DA1 13.4 FORWARD INSULATION C212 40 40 RED

DRY PROVISION STORE 5DA1 13.4 FORWARD INSULATION C061 40 27925 4th COAT OF FINISHER APPLIED THE SAME AS 3rd COAT

DRY PROVISION STORE 5DA1 34.9 AFT INSULATION C212 40 40 RED

DRY PROVISION STORE 5DA1 34.9 AFT INSULATION C061 40 27925 4th COAT OF FINISHER APPLIED THE SAME AS 3rd COAT

DRY PROVISION STORE 5DA1 24.3 PORT C212 40 40 RED

DRY PROVISION STORE 5DA1 24.3 PORT C061 40 27925 4th COAT OF FINISHER APPLIED THE SAME AS 3rd COAT

DRY PROVISION STORE 5DA1 19.5 STBD INSULATION C212 40 40 RED

DRY PROVISION STORE 5DA1 19.5 STBD INSULATION C061 40 27925 4th COAT OF FINISHER APPLIED THE SAME AS 3rd COAT

DRY PROVISION STORE 5DA1 5.4 OTHERS C212 40 40 RED DADO 150mm HIGH.

DRY PROVISION STORE 5DA1 5.4 OTHERS C061 40 16076DADO 150mm HIGH. 4th COAT OF FINISHER APPLIED THE SAME AS 3rd COAT.

BEER & SOFT DRINK STORE 5DA2 45.8 ST DECK C413 Manufacturer

BEER & SOFT DRINK STORE 5DA2 45.8 ST DECK C413 Manufacturer

BEER & SOFT DRINK STORE 5DA2 45.8 ST DECK C404 40 16076 4th COAT OF FINISHER APPLIED THE SAME AS 3rd COAT

BEER & SOFT DRINK STORE 5DA2 53.9 DECKHEAD NOTE 4 C212 40 40 RED PART INSULATED.


Primer

DCZ Area M2

Surface1st Coat

µm


Name

Remarks

Rev: C


µm2nd Coat

µm


Finisher


µm3rd Coat

µm1st Coat

µm

BEER & SOFT DRINK STORE 5DA2 53.9 DECKHEAD NOTE 4 C061 40 27925 PART INSULATED. 4th COAT OF FINISHER APPLIED THE SAME AS 3rd

BEER & SOFT DRINK STORE 5DA2 13.4 FORWARD INSULATION NOTE 4 C212 40 40 RED

BEER & SOFT DRINK STORE 5DA2 13.4 FORWARD INSULATION NOTE 4 C061 40 27925 4th COAT OF FINISHER APPLIED THE SAME AS 3rd COAT

BEER & SOFT DRINK STORE 5DA2 20.3 AFT NOTE 4 C212 40 40 RED PART INSULATED.

BEER & SOFT DRINK STORE 5DA2 20.3 AFT NOTE 4 C061 40 27925 PART INSULATED. 4th COAT OF FINISHER APPLIED THE SAME AS 3rd

BEER & SOFT DRINK STORE 5DA2 19.5 PORT INSULATION NOTE 4 C212 40 40 RED

BEER & SOFT DRINK STORE 5DA2 19.5 PORT INSULATION NOTE 4 C061 40 27925 4th COAT OF FINISHER APPLIED THE SAME AS 3rd COAT

BEER & SOFT DRINK STORE 5DA2 24.3 STBD C212 40 40 REDBEER & SOFT DRINK STORE 5DA2 24.3 STBD C061 40 27925BEER & SOFT DRINK STORE 5DA2 4.5 OTHERS C212 40 40 RED DADO 150mm HIGH.

BEER & SOFT DRINK STORE 5DA2 4.5 OTHERS C061 40 16076DADO 150mm HIGH. 4th COAT OF FINISHER APPLIED THE SAME AS 3rd COAT.

DEEP SHELTER STATION NO.1 5DZ0 12.7 ST DECK 76 C413 64 DK COVERINGDEEP SHELTER STATION NO.1 5DZ0 9.6 DECKHEAD C212 36 36 C061 30 30 WHITE 27925DEEP SHELTER STATION NO.1 5DZ0 9.6 FORWARD C212 36 36 C061 30 30 GREY 27880DEEP SHELTER STATION NO.1 5DZ0 9.6 AFT C212 36 36 C061 30 30 GREY 27880DEEP SHELTER STATION NO.1 5DZ0 6.8 PORT C212 36 36 INSULATION NOTE 4 C061 30 30 GREY 27880DEEP SHELTER STATION NO.1 5DZ0 6.8 STBD C212 36 36 INSULATION NOTE 4 C061 30 30 GREY 27880DEEP SHELTER STATION NO.1 5DZ0 N/A OTHERS C061 30 30 GREY 16076 DADO (150mm HIGH)IWO COFFERDAM UNDER NO.1 & 2 RFW TANKS ONLY 5DZ0 20.0 ST DECK C413 125-150 DK COVERING

IWO COFFERDAM UNDER NO.1 & 2 RFW TANKS ONLY 5DZ0 N/A ST DECK NON-

TRAFFIC C061 30 30 GREY 16076

RESERVE FEED TANK NO.1 5DZ1 16.5 ALL INTERIOR SURFACES C193 125 GREY

RESERVE FEED TANK NO.1 5DZ1 16.5 ALL INTERIOR SURFACES C193 125 WHITE

RESERVE FEED TANK NO.2 5DZ3 30.1 ALL INTERIOR SURFACES C193 125 GREY

RESERVE FEED TANK NO.2 5DZ3 30.1 ALL INTERIOR SURFACES C193 125 WHITE

FAMR CASING(3DECK TO 1 DECK) 5E 14.3 DECKHEAD (11700 ABL) 76 INSULATION NOTE 4 C076 30 30 GREY 26480

FAMR CASING(3DECK TO 1 DECK) 5E 26.1 FORWARD 76 INSULATION NOTE 5 GREY 26480FAMR CASING(3DECK TO 1 DECK) 5E 26.1 AFT 76 INSULATION NOTE5 GREY 26480FAMR CASING(3DECK TO 1 DECK) 5E 17.8 PORT 76 INSULATION NOTE5 GREY 26480FAMR CASING(3DECK TO 1 DECK) 5E 17.8 STBD 76 INSULATION NOTE 5 GREY 26480

FORWARD AUXILIARY MACHINERY ROOM 5E 80.7 ST DECK C207 See Remarks BUFF



Primer

DCZ Area M2

Surface1st Coat

µm


Name

Remarks

Rev: C


µm2nd Coat

µm


Finisher


µm3rd Coat

µm1st Coat

µm

FORWARD AUXILIARY MACHINERY ROOM 5E 80.7 ST DECK C207 See Remarks OFF-WHITE


FORWARD AUXILIARY MACHINERY ROOM 5E 161.8 DECKHEAD C212 36 36 INSULATION C061 30 30 WHITE 27925FORWARD AUXILIARY MACHINERY ROOM 5E 34.3 FORWARD C212 36 36 INSULATION NOTE 5 WHITE 27925FORWARD AUXILIARY MACHINERY ROOM 5E 34.3 AFT C212 36 36 INSULATION NOTE 5 WHITE 27925FORWARD AUXILIARY MACHINERY ROOM 5E 103.7 PORT C212 36 36 INSULATION NOTE 5 WHITE 27925FORWARD AUXILIARY MACHINERY ROOM 5E 103.7 STBD C212 36 36 INSULATION NOTE 5 WHITE 27925FORWARD AUXILIARY MACHINERY ROOM 5E 202.0 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480 ABOVE BOOT TOP

FORWARD AUXILIARY MACHINERY ROOM 5E N/A OTHERS C207 See Remarks BUFF DECK ENCLOSED BY SEATS. D.F.T.


FORWARD AUXILIARY MACHINERY ROOM 5E N/A OTHERS C207 See Remarks OFF-WHITE DECK ENCLOSED BY SEATS. D.F.T.

PER COAT IS 125-150 MICRONSFORWARD AUXILIARY MACHINERY ROOM 5E N/A OTHERS C212 36 36 C061 30 30 WHITE 27925 EXT. OF LUBE OIL TANK

FORWARD AUXILIARY MACHINERY ROOM 5E N/A OTHERS C212 36 36 C061 30 30 WHITE 27925 DECKHEAD STIFFENING CLEAR OF INSULATION

DIESEL FUEL OIL TANK NO.1 5FA1 121.3 ALL INTERIOR SURFACES C193 125 GREY

DIESEL FUEL OIL TANK NO.1 5FA1 121.3 ALL INTERIOR SURFACES C193 125 WHITE

DIESEL FUEL OIL TANK NO.2 5FA2 121.3 ALL INTERIOR SURFACES C193 125 GREY

DIESEL FUEL OIL TANK NO.2 5FA2 121.3 ALL INTERIOR SURFACES C193 125 WHITE

AAMR CASING(3 DECK TO 01 DECK) 5H 9.2 ST DECK(2 DECK) 76 C076 30 30 GREY 26480

AAMR CASING(3 DECK TO 01 DECK) 5H 13.5DECKHEAD (UNDER 01

DECK)76 INSULATION NOTE 4 C076 30 30 GREY 26480

AAMR CASING(3 DECK TO 01 DECK) 5H 10.7 DECKHEAD (UNDER 1 DECK) 76 INSULATION NOTE 4 C076 30 30 GREY 26480

AAMR CASING(3 DECK TO 01 DECK) 5H 29.3 FORWARD 76 INSULATION NOTE 5 GREY 26480AAMR CASING(3 DECK TO 01 DECK) 5H 33.5 AFT 76 INSULATION NOTE 5 GREY 26480AAMR CASING(3 DECK TO 01 DECK) 5H 35.1 PORT 76 INSULATION NOTE 5 GREY 26480AAMR CASING(3 DECK TO 01 DECK) 5H 34.2 STBD 76 INSULATION NOTE 5 GREY 26480

AAMR CASING(3 DECK TO 01 DECK) 5H 19.2 AAMR CASING EXTERIOR 76 C045 40 C411 30 30 30 GREY 26480

AFT AUXILIARY MACHINERY ROOM 5H 127.4 ST DECK C207 See Remarks BUFF


AFT AUXILIARY MACHINERY ROOM 5H 127.4 ST DECK C207 See Remarks OFF-WHITE


AFT AUXILIARY MACHINERY ROOM 5H 138.2 DECKHEAD C212 36 36 INSULATION C061 30 30 WHITE 27925


Primer

DCZ Area M2

Surface1st Coat

µm


Name

Remarks

Rev: C


µm2nd Coat

µm


Finisher


µm3rd Coat

µm1st Coat

µm

AFT AUXILIARY MACHINERY ROOM 5H 83.0 FORWARD C212 36 36 INSULATION NOTE 5 WHITE 27925AFT AUXILIARY MACHINERY ROOM 5H 83.0 AFT C212 36 36 INSULATION NOTE 5 WHITE 27925AFT AUXILIARY MACHINERY ROOM 5H 56.5 PORT C212 36 36 INSULATION NOTE 5 WHITE 27925AFT AUXILIARY MACHINERY ROOM 5H 56.5 STBD C212 36 36 INSULATION NOTE 5 WHITE 27925AFT AUXILIARY MACHINERY ROOM 5H 220.6 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480 ABOVE BOOT TOP

AFT AUXILIARY MACHINERY ROOM 5H N/A OTHERS C212 36 36 C207 See Remarks BUFF EXT. OF LUBE OIL TANK. D.F.T. PER

COAT IS 125-150 MICRONS.

AFT AUXILIARY MACHINERY ROOM 5H N/A OTHERS C207 See Remarks OFF-WHITE D.F.T. PER COAT IS 125-150

MICRONS.

AFT AUXILIARY MACHINERY ROOM 5H N/A OTHERS C212 36 36 C061 30 30 WHITE 513-201 DECKHEAD STIFFENING CLEAR OF INSULATION

SEWAGE TREATMENT PLANT & GLAND COMPARTMENT 5JA0 12.8 INTERIOR

SURFACES C207 See Remarks BUFF D.F.T. PER COAT IS 125-150

MICRONS.

SEWAGE TREATMENT PLANT & GLAND COMPARTMENT 5JA0 12.8 INTERIOR

SURFACES C207 See Remarks OFF-WHITE D.F.T. PER COAT IS 125-150

MICRONS.

BLACK & GREY WATER COLLECTION TANK 5JB0 37.0 INTERIOR SURFACES C409 See

Remarks BUFF AS PER D-23-003-005/SF-002

BLACK & GREY WATER COLLECTION TANK 5JB0 37.0 INTERIOR SURFACES C409 See

Remarks OFF-WHITE AS PER D-23-003-005/SF-002

BLACK & GREY WATER COLLECTION TANK 5JB0 37.0 INTERIOR SURFACES

FFH332 TO FFH341. AIR & STEEL TEMPS TO BE ABOVE 17°C. TANK MUST BE BLASTED TO AND HELD AT SSPC SP 5 WHITE METAL PRIOR TO APPLICATION OF PRIMER. ALL WELDS, SECTIONS, EDGES, FITTINGS, ETC TO BE STRIPE COATED. TANK MUST BE PIN HOLE TESTED. ACCEPTABLE LEVEL OF DEFECTS: ZERO.





QUIET MEDIUM TANK 5JB1 18.3 INTERIOR SURFACES C409 SEE

REMARK BUFF AS PER D-23-003-005/SF-002

QUIET MEDIUM TANK 5JB1 18.3 INTERIOR SURFACES C409 SEE

REMARK OFF-WHITE AS PER D-23-003-005/SF-002


Primer

DCZ Area M2

Surface1st Coat

µm


Name

Remarks

Rev: C


µm2nd Coat

µm


Finisher


µm3rd Coat

µm1st Coat

µm

CABLE LOCKER NO. 1 4BA 32.6 INTERIOR SURFACES 76 C183 64 PERFORATED GALVINIZED LINING

UNPAINTED

CABLE LOCKER NO. 1 4BA 10.3 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480 ABOVE BOOT TOP

CABLE LOCKER NO. 2 4BA 32.6 INTERIOR SURFACES 76 C183 64 PERFORATED GALVINIZED LINING

UNPAINTED

CABLE LOCKER NO. 2 4BA 10.3 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480 ABOVE BOOT TOP

BAGGAGE STORE 4BZ 6.6 ST DECK TRAFFIC 76 C183 125-150 1-GP-200 750-1000 GREY 36076

BAGGAGE STORE 4BZ 2.2 ST DECK NON-TRAFFIC

C413 AND C045 C061 OR C177 30 30 GREY 16076

BAGGAGE STORE 4BZ 14.3 DECKHEAD C212 36 36 NOTE 4 C061 30 30 WHITE 27925 PART INSULATION

BAGGAGE STORE 4BZ 10.3 FORWARD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925BAGGAGE STORE 4BZ 13.1 AFT C212 36 36 C061 30 30 WHITE 27925BAGGAGE STORE 4BZ 7.5 PORT C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925BAGGAGE STORE 4BZ 7.5 STBD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925BAGGAGE STORE 4BZ 15.0 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480 ABOVE BOOT TOPBAGGAGE STORE 4BZ 10.8 OTHERS C061 30 30 GREY 16076 DADO 900mm HIGH

57MM MAGAZINE 4CA 14.1 ST DECK TRAFFIC C413 C200 750-1000 GREY 36076

57MM MAGAZINE 4CA 24.2 ST DECK NON-TRAFFIC

C413 AND C045 C061 OR C177 30 30 GREY 16076

57MM MAGAZINE 4CA 56.4 DECKHEAD C212 36 36 NOTE 4 C061 30 30 WHITE 27925 PART INSULATION57MM MAGAZINE 4CA 13.1 FORWARD C212 36 36 NOTE 4 C061 30 30 WHITE 27925 PART INSULATION57MM MAGAZINE 4CA 25.6 AFT C212 36 36 C061 30 30 WHITE 2792557MM MAGAZINE 4CA 17.4 PORT C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 2792557MM MAGAZINE 4CA 22.4 STBD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 2792557MM MAGAZINE 4CA 39.8 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480 ABOVE BOOT TOP57MM MAGAZINE 4CA 4.1 OTHERS C061 30 30 GREY 16076 DADO 150mm HIGH

RAS TRUNK 4CB0 34.3 ALL INTERIOR SURFACES 76

LOBBY 4CB2 5.5 ST DECK TRAFFIC C413 64 C200 750-1000 GREY 36076

LOBBY 4CB2 2.0 ST DECK NON-TRAFFIC

C413 AND C045 C061 OR C177 30 30 GREY 16076

LOBBY 4CB2 11.3 DECKHEAD C212 36 36 NOTE 4 C061 30 30 WHITE 27925 PART INSULATIONLOBBY 4CB2 8.4 FORWARD C212 36 36 C061 30 30 GREY 27880LOBBY 4CB2 10.2 AFT C212 36 36 C061 30 30 GREY 27880LOBBY 4CB2 7.4 PORT C212 36 36 INSULATION NOTE 4 C061 30 30 GREY 27880LOBBY 4CB2 7.8 STBD C212 36 36 C061 30 30 GREY 27880LOBBY 4CB2 7.4 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480 ABOVE BOOT TOPLOBBY 4CB2 1.7 OTHERS C061 30 30 GREY 16076 DADO 150mm HIGH

CCER NO. 4 4CZ 15.3 ST DECK TRAFFIC C413 C200 750-1000 GREY 16076

CCER NO. 4 4CZ 8.2 ST DECK NON-TRAFFIC

C413 AND C045 C061 OR C177 30 30 GREY 16076

CCER NO. 4 4CZ 32.4 DECKHEAD C212 36 36 NOTE 4 C061 30 30 WHITE 27925 PART INSULATIONCCER NO. 4 4CZ 24.9 FORWARD C212 36 36 NOTE 4 C061 30 30 WHITE 27925 PART INSULATIONCCER NO. 4 4CZ 24.3 AFT C212 36 36 C061 30 30 WHITE 27925CCER NO. 4 4CZ 7.4 PORT C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925CCER NO. 4 4CZ 9.9 STBD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925


Primer

DCZ Area M2

Surface1st Coat

µm


Name

Remarks

Rev: C


µm2nd Coat

µm


Finisher


µm3rd Coat

µm1st Coat

µm

CCER NO. 4 4CZ 17.3 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480 ABOVE BOOT TOP

FORWARD SONAR INSTRUMENT SPACE 4DA 16.5 ST DECK TRAFFIC C413 Manufact

urer

FORWARD SONAR INSTRUMENT SPACE 4DA 16.5 ST DECK TRAFFIC C413 Manufact

urer

FORWARD SONAR INSTRUMENT SPACE 4DA 16.5 ST DECK TRAFFIC C200 750-1000 36076 4th COAT OF FINISHER APPLIED THE

SAME AS 3rd COAT

FORWARD SONAR INSTRUMENT SPACE 4DA 15.7 ST DECK NON-TRAFFIC C413 Manufact

urer

FORWARD SONAR INSTRUMENT SPACE 4DA 15.7 ST DECK NON-TRAFFIC C413 Manufact

urer

FORWARD SONAR INSTRUMENT SPACE 4DA 15.7 ST DECK NON-TRAFFIC C404 40 16076 4th COAT OF FINISHER APPLIED THE

SAME AS 3rd COAT

FORWARD SONAR INSTRUMENT SPACE 4DA 41.9 DECKHEAD NOTE 4 C212 40 40 RED PART INSULATION.

FORWARD SONAR INSTRUMENT SPACE 4DA 41.9 DECKHEAD NOTE 4 C061 40 27925PART INSULATION. 4th COAT OF FINISHER APPLIED THE SAME AS 3rd COAT

FORWARD SONAR INSTRUMENT SPACE 4DA 24.3 FORWARD C212 40 40 RED

FORWARD SONAR INSTRUMENT SPACE 4DA 24.3 FORWARD C061 40 27925 4th COAT OF FINISHER APPLIED THE SAME AS 3rd COAT

FORWARD SONAR INSTRUMENT SPACE 4DA 26.9 AFT C212 40 40 RED

FORWARD SONAR INSTRUMENT SPACE 4DA 26.9 AFT C061 40 27925 4th COAT OF FINISHER APPLIED THE SAME AS 3rd COAT

FORWARD SONAR INSTRUMENT SPACE 4DA 9.9 PORT INSULATION NOTE 4 C212 40 40 RED

FORWARD SONAR INSTRUMENT SPACE 4DA 9.9 PORT INSULATION NOTE 4 C061 40 27925 4th COAT OF FINISHER APPLIED THE SAME AS 3rd COAT

FORWARD SONAR INSTRUMENT SPACE 4DA 9.9 STBD INSULATION NOTE 4 C212 40 40 RED

FORWARD SONAR INSTRUMENT SPACE 4DA 9.9 STBD INSULATION NOTE 4 C061 40 27925 4th COAT OF FINISHER APPLIED THE SAME AS 3rd COAT

FORWARD GYRO ROOM 4DB0 3.2 ST DECK TRAFFIC C413 Manufact

urer

FORWARD GYRO ROOM 4DB0 3.2 ST DECK TRAFFIC C413 Manufact

urer

FORWARD GYRO ROOM 4DB0 3.2 ST DECK TRAFFIC C200 750-1000 36076 4th COAT OF FINISHER APPLIED THE

SAME AS 3rd COAT

FORWARD GYRO ROOM 4DB0 2.3 ST DECK NON-TRAFFIC C413 Manufact

urer

FORWARD GYRO ROOM 4DB0 2.3 ST DECK NON-TRAFFIC C413 Manufact

urer

FORWARD GYRO ROOM 4DB0 2.3 ST DECK NON-TRAFFIC C404 40 16076 4th COAT OF FINISHER APPLIED THE

SAME AS 3rd COAT

FORWARD GYRO ROOM 4DB0 5.5 DECKHEAD C212 40 40 RED

FORWARD GYRO ROOM 4DB0 5.5 DECKHEAD C061 40 27925 4th COAT OF FINISHER APPLIED THE SAME AS 3rd COAT

FORWARD GYRO ROOM 4DB0 6.7 FORWARD C212 40 40 RED

FORWARD GYRO ROOM 4DB0 6.7 FORWARD C061 40 27925 4th COAT OF FINISHER APPLIED THE SAME AS 3rd COAT

FORWARD GYRO ROOM 4DB0 6.7 AFT C212 40 40 RED

FORWARD GYRO ROOM 4DB0 6.7 AFT C061 40 27925 4th COAT OF FINISHER APPLIED THE SAME AS 3rd COAT

FORWARD GYRO ROOM 4DB0 4.9 PORT C212 40 40 RED


Primer

DCZ Area M2

Surface1st Coat

µm


Name

Remarks

Rev: C


µm2nd Coat

µm


Finisher


µm3rd Coat

µm1st Coat

µm

FORWARD GYRO ROOM 4DB0 4.9 PORT C061 40 27925 4th COAT OF FINISHER APPLIED THE SAME AS 3rd COAT

FORWARD GYRO ROOM 4DB0 4.9 STBD C212 40 40 RED

FORWARD GYRO ROOM 4DB0 4.9 STBD C061 40 27925 4th COAT OF FINISHER APPLIED THE SAME AS 3rd COAT

FREEZER STOREROOM 4DC1 31.7 ST DECK C413 125-150 125-150

FREEZER STOREROOM 4DC1 36.5 DECKHEAD C212 36 36 SEE INSULATED REFRIGERATED SPACES DRAWING

FREEZER STOREROOM 4DC1 4.1 FORWARD C212 36 36 SEE INSULATED REFRIGERATED SPACES DRAWING

FREEZER STOREROOM 4DC1 12.8 AFT C212 36 36 SEE INSULATED REFRIGERATED SPACES DRAWING

FREEZER STOREROOM 4DC1 13.7 PORT C212 36 36 SEE INSULATED REFRIGERATED SPACES DRAWING

FREEZER STOREROOM 4DC1 20.3 STBD C212 36 36 SEE INSULATED REFRIGERATED SPACES DRAWING

FREEZER STOREROOM 4DC1 20.6 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480 ABOVE BOOTTOP

DAIRY STOREROOM 4DC2 31.1 ST DECK C402 Manufacturer

SEE INSULATED REFRIGERATED SPACES DRAWING

DAIRY STOREROOM 4DC2 31.1 ST DECK C403 Manufacturer


DAIRY STOREROOM 4DC2 41.1 DECKHEAD C212 40 40 RED SEE INSULATED REFRIGERATED SPACES DRAWING

DAIRY STOREROOM 4DC2 9.7 FORWARD C212 40 40 RED SEE INSULATED REFRIGERATED SPACES DRAWING

DAIRY STOREROOM 4DC2 15.3 AFT C212 40 40 RED SEE INSULATED REFRIGERATED SPACES DRAWING

DAIRY STOREROOM 4DC2 18.7 PORT C212 40 40 RED SEE INSULATED REFRIGERATED SPACES DRAWING

DAIRY STOREROOM 4DC2 22.2 STBD C212 40 40 RED SEE INSULATED REFRIGERATED SPACES DRAWING

POTATO LOCKER 4DY2 3.6 ST DECK C402 Manufacturer


POTATO LOCKER 4DY2 3.6 ST DECK C403 Manufacturer


POTATO LOCKER 4DY2 5.7 DECKHEAD C212 40 40 RED SEE INSULATED REFRIGERATED SPACES DRAWING

POTATO LOCKER 4DY2 7.0 FORWARD C212 40 40 RED SEE INSULATED REFRIGERATED SPACES DRAWING

POTATO LOCKER 4DY2 7.6 AFT C212 40 40 RED SEE INSULATED REFRIGERATED SPACES DRAWING

POTATO LOCKER 4DY2 4.6 PORT C212 40 40 RED SEE INSULATED REFRIGERATED SPACES DRAWING

POTATO LOCKER 4DY2 4.9 STBD C212 40 40 RED SEE INSULATED REFRIGERATED SPACES DRAWING

REFER MACHINERY SPACE 4DZ0 2.8 ST DECK TRAFFIC C413 C200 750-1000 GREY 36076

REFER MACHINERY SPACE 4DZ0 25.9 ST DECK NON TRAFFIC

C413 AND C045 C061 OR C177 30 30 GREY 16076

REFER MACHINERY SPACE 4DZ0 33.1 DECKHEAD C212 36 36 INSULATION C061 30 30 WHITE 27925REFER MACHINERY SPACE 4DZ0 14.3 FORWARD C212 36 36 C061 30 30 WHITE 27925REFER MACHINERY SPACE 4DZ0 16.5 AFT C212 36 36 C061 30 30 WHITE 27925REFER MACHINERY SPACE 4DZ0 14.4 PORT C212 36 36 C061 30 30 WHITE 27925REFER MACHINERY SPACE 4DZ0 14.4 STBD C212 36 36 C061 30 30 WHITE 27925


Primer

DCZ Area M2

Surface1st Coat

µm


Name

Remarks

Rev: C


µm2nd Coat

µm


Finisher


µm3rd Coat

µm1st Coat

µm

REFER MACHINERY SPACE 4DZ0 OTHERS C061 30 30 GREY 16076 DADO (150mm HIGH)FRUIT & VEG STOREROOM 4DZ1 13.2 ST DECK C413 125-150 125-150

FRUIT & VEG STOREROOM 4DZ1 15.2 DECKHEAD C212 36 36 SEE INSULATED REFRIGERATED SPACES DRAWING

FRUIT & VEG STOREROOM 4DZ1 6.9 FORWARD C212 36 36 SEE INSULATED REFRIGERATED SPACES DRAWING

FRUIT & VEG STOREROOM 4DZ1 8.6 AFT C212 36 36 SEE INSULATED REFRIGERATED SPACES DRAWING

FRUIT & VEG STOREROOM 4DZ1 11.8 PORT C212 36 36 SEE INSULATED REFRIGERATED SPACES DRAWING

FRUIT & VEG STOREROOM 4DZ1 11.8 STBD C212 36 36 SEE INSULATED REFRIGERATED SPACES DRAWING

FRUIT & VEG STOREROOM 4DZ1 12.1 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480 ABOVE BOOTTOP

FLOUR STORE 4DZ2 7.8 ST DECK DK COVERING C402 Manufacturer

FLOUR STORE 4DZ2 7.8 ST DECK DK COVERING C403 Manufacturer

FLOUR STORE 4DZ2 10.0 DECKHEAD INSULATION C212 40 40 RED

FLOUR STORE 4DZ2 10.0 DECKHEAD INSULATION C061 40 27925 4th COAT OF FINISHER APPLIED THE SAME AS 3rd COAT

FLOUR STORE 4DZ2 7.9 FORWARD INSULATION C212 40 40 RED

FLOUR STORE 4DZ2 7.9 FORWARD INSULATION C061 40 27925 4th COAT OF FINISHER APPLIED THE SAME AS 3rd COAT

FLOUR STORE 4DZ2 8.5 AFT C212 40 40 RED

FLOUR STORE 4DZ2 8.5 AFT C061 40 27925 4th COAT OF FINISHER APPLIED THE SAME AS 3rd COAT

FLOUR STORE 4DZ2 7.4 PORT INSULATION C212 40 40 RED

FLOUR STORE 4DZ2 7.4 PORT INSULATION C061 40 27925 4th COAT OF FINISHER APPLIED THE SAME AS 3rd COAT

FLOUR STORE 4DZ2 7.3 STBD C212 40 40 RED

FLOUR STORE 4DZ2 7.3 STBD C061 40 27925 4th COAT OF FINISHER APPLIED THE SAME AS 3rd COAT

FLOUR STORE 4DZ2 10.1 OTHERS C212 40 40 RED

FLOUR STORE 4DZ2 10.1 OTHERS C061 40 16076DADO 900mm HIGH. 4th COAT OF FINISHER APPLIED THE SAME AS 3rd COAT

LUBE OIL STORAGE TANK NO. 1 4EA0 30.1 ALL INTERIOR SURFACES C193 125 GREY

LUBE OIL STORAGE TANK NO. 1 4EA0 30.1 ALL INTERIOR SURFACES C193 125 WHITE

LUBE OIL STORAGE TANK NO.2 4HA1 27.4 INTERIOR SURFACE C193 125 GREY

LUBE OIL STORAGE TANK NO.2 4HA1 27.4 INTERIOR SURFACE C193 125 WHITE

AFTER GYRO ROOM 4JA0 4.9 ST DECK TRAFFIC C413 125-150 C200 675 GREY 36076

AFTER GYRO ROOM 4JA0 2.1 ST DECK NON TRAFFIC

C413 AND C045 C061 OR C177 30 30 GREY 16076

AFTER GYRO ROOM 4JA0 7.6 DECKHEAD C212 36 36 C061 30 30 WHITE 27925AFTER GYRO ROOM 4JA0 7.2 FORWARD C212 36 36 C061 30 30 WHITE 27925AFTER GYRO ROOM 4JA0 7.1 AFT C212 36 36 C061 30 30 WHITE 27925AFTER GYRO ROOM 4JA0 6.7 PORT C212 36 36 C061 30 30 WHITE 27925AFTER GYRO ROOM 4JA0 6.0 STBD C212 36 36 C061 30 30 WHITE 27925LAUNDRY 4JA1 39.8 ST DECK C413 125-150 DK COVERINGLAUNDRY 4JA1 48.3 DECKHEAD C212 36 36 NOTE 4 C061 30 30 WHITE 27925 PART INSULATED.LAUNDRY 4JA1 16.6 FORWARD C212 36 36 C061 30 30 WHITE 27925


Primer

DCZ Area M2

Surface1st Coat

µm


Name

Remarks

Rev: C


µm2nd Coat

µm


Finisher


µm3rd Coat

µm1st Coat

µm

LAUNDRY 4JA1 10.0 AFT C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925LAUNDRY 4JA1 27.3 PORT C212 36 36 C061 30 30 WHITE 27925

LAUNDRY 4JA1 23.7 STBD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925

CLEAR OF FIBREGLASS LINING. APPLY 2 COATS 38 µm OF C021 TO THE DOUBLE LAYER OF FIBREGLASS, COLOUR TO BE WHITE.

LAUNDRY 4JA1 22.0 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480 ABOVE BOOTTOPLOBBY SHELTER STATION NO. 2 4JA2 24.3 ST DECK C413 125-150 DK COVERINGLOBBY SHELTER STATION NO. 2 4JA2 26.1 DECKHEAD C212 36 36 C061 30 30 WHITE 27925LOBBY SHELTER STATION NO. 2 4JA2 17.6 FORWARD C212 36 36 C061 30 30 GREY 27880LOBBY SHELTER STATION NO. 2 4JA2 15.2 AFT C212 36 36 C061 30 30 GREY 27880LOBBY SHELTER STATION NO. 2 4JA2 14.7 PORT C212 36 36 C061 30 30 GREY 27880LOBBY SHELTER STATION NO. 2 4JA2 3.8 STBD C212 36 36 C061 30 30 GREY 27880LOBBY SHELTER STATION NO. 2 4JA2 3.1 OTHERS C061 30 30 GREY 16076 DADO (150 mm HIGH)CBRN STORE 4JA4 10.9 ST DECK C413 125-150 DK COVERINGCBRN STORE 4JA4 13.2 DECKHEAD C212 36 36 NOTE 4 C061 30 30 WHITE 27925 PART INSULATED.CBRN STORE 4JA4 11.0 FORWARD C212 36 36 C061 30 30 WHITE 27925CBRN STORE 4JA4 10.1 AFT C212 36 36 C061 30 30 WHITE 27925CBRN STORE 4JA4 7.9 PORT C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925CBRN STORE 4JA4 7.4 STBD C212 36 36 C061 30 30 WHITE 27925CBRN STORE 4JA4 7.4 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480 ABOVE BOOTTOPCBRN STORE 4JA4 12.7 OTHERS C061 30 30 GREY 16076 DADO (900 mm HIGH)CREW'S LAUNDROMAT 4JB2 9.5 ST DECK C413 DK COVERINGCREW'S LAUNDROMAT 4JB2 11.9 DECKHEAD C212 36 36 NOTE 4 C061 30 30 WHITE 27925 PART INSULATED.CREW'S LAUNDROMAT 4JB2 10.1 FORWARD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925CREW'S LAUNDROMAT 4JB2 10.8 AFT C212 36 36 C061 30 30 WHITE 27925CREW'S LAUNDROMAT 4JB2 7.9 PORT C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925CREW'S LAUNDROMAT 4JB2 5.1 STBD C212 36 36 C061 30 30 WHITE 27925CREW'S LAUNDROMAT 4JB2 7.4 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480 ABOVE BOOTTOP

FCER NO. 3 4JZ0 18.4 ST DECK TRAFFIC C413 C200 750-1000 GREY 36076

FCER NO. 3 4JZ0 7.9 ST DECK NON TRAFFIC

C413 AND C045 C061 OR C177 30 30 GREY 16076

FCER NO. 3 4JZ0 28.4 DECKHEAD C212 36 36 C061 30 30 WHITE 27925FCER NO. 3 4JZ0 21.1 FORWARD C212 36 36 C061 30 30 WHITE 27925FCER NO. 3 4JZ0 17.6 AFT C212 36 36 C061 30 30 WHITE 27925FCER NO. 3 4JZ0 7.3 PORT C212 36 36 C061 30 30 WHITE 27925FCER NO. 3 4JZ0 12.3 STBD C212 36 36 C061 30 30 WHITE 27925ENTERTAINMENT BROADCAST ROOM 4JZ2 11.0 ST DECK C413 125-150 DK COVERINGENTERTAINMENT BROADCAST ROOM 4JZ2 13.7 DECKHEAD C212 36 36 NOTE 4 C061 30 30 WHITE 27925 PART INSULATED.ENTERTAINMENT BROADCAST ROOM 4JZ2 10.8 FORWARD C212 36 36 C061 30 30 WHITE 27925ENTERTAINMENT BROADCAST ROOM 4JZ2 9.3 AFT C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925ENTERTAINMENT BROADCAST ROOM 4JZ2 7.9 PORT C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925ENTERTAINMENT BROADCAST ROOM 4JZ2 9.2 STBD C212 36 36 C061 30 30 WHITE 27925ENTERTAINMENT BROADCAST ROOM 4JZ2 7.4 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480 ABOVE BOOTTOP

AIR LOCK 4KA0 0.6 ST DECK TRAFFIC C413 C200 750-1000 GREY 36076

AIR LOCK 4KA0 2.5 ST DECK NON TRAFFIC

C413 AND C045 C061 OR C177 30 30 GREY 16076

AIR LOCK 4KA0 3.3 DECKHEAD C212 36 36 C061 30 30 WHITE 27925AIR LOCK 4KA0 2.7 FORWARD C212 36 36 C061 30 30 GREY 27880AIR LOCK 4KA0 2.7 AFT C212 36 36 C061 30 30 GREY 27880AIR LOCK 4KA0 7.2 PORT C212 36 36 C061 30 30 GREY 27880AIR LOCK 4KA0 7.2 STBD C212 36 36 C061 30 30 GREY 27880


Primer

DCZ Area M2

Surface1st Coat

µm


Name

Remarks

Rev: C


µm2nd Coat

µm


Finisher


µm3rd Coat

µm1st Coat

µm

AIR LOCK 4KA0 1.2 OTHERS C061 30 30 GREY 16076 DADO (150 mm HIGH)

JP5 PUMP ROOM 4KA1 8.5 ST DECK TRAFFIC C413 125-150 C200 750-1000 GREY 36076

JP5 PUMP ROOM 4KA1 8.5 ST DECK NON TRAFFIC

C413 AND C045 C061 OR C177 30 30 GREY 16076

JP5 PUMP ROOM 4KA1 18.3 DECKHEAD C212 36 36 INSULATION C061 30 30 WHITE 27925JP5 PUMP ROOM 4KA1 8.8 FORWARD C212 36 36 INSULATION NOTE 5 WHITE 27925JP5 PUMP ROOM 4KA1 8.8 AFT C212 36 36 INSULATION NOTE 5 WHITE 27925JP5 PUMP ROOM 4KA1 21.2 PORT C212 36 36 INSULATION NOTE 5 WHITE 27925JP5 PUMP ROOM 4KA1 21.2 STBD C212 36 36 INSULATION NOTE 5 WHITE 27925JP5 PUMP ROOM 4KA1 2.6 OTHERS C061 30 30 GREY 16076 DADO (900 mm HIGH)LOBBY 4KA2 3.8 ST DECK C413 125-150 DK COVERINGLOBBY 4KA2 4.1 DECKHEAD C212 36 36 C061 30 30 WHITE 27925LOBBY 4KA2 3.1 FORWARD C212 36 36 C061 30 30 GREY 27880LOBBY 4KA2 3.1 AFT C212 36 36 C061 30 30 GREY 27880LOBBY 4KA2 7.2 PORT C212 36 36 C061 30 30 GREY 27880LOBBY 4KA2 7.2 STBD C212 36 36 C061 30 30 GREY 27880LOBBY 4KA2 1.2 OTHERS C061 30 30 GREY 16076 DADO (150 mm HIGH)GENERAL STORE NO. 2 4KZ 98.2 ST DECK C413 125-150 DK COVERING FALSE DECK AT SHIPS SIDEGENERAL STORE NO. 2 4KZ 125.8 DECKHEAD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925GENERAL STORE NO. 2 4KZ 57.5 FORWARD C212 36 36 C061 30 30 WHITE 27925GENERAL STORE NO. 2 4KZ 36.0 AFT C212 36 36 C061 30 30 WHITE 27925GENERAL STORE NO. 2 4KZ 26.5 PORT C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925GENERAL STORE NO. 2 4KZ 26.5 STBD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925GENERAL STORE NO. 2 4KZ 49.0 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480 ABOVE BOOTTOPGENERAL STORE NO. 2 4KZ 48.8 OTHERS C061 30 30 GREY 16076 DADO (900 mm HIGH)

GENERAL STORE NO. 3 4L 57.1 ST DECK C207 See Remarks BUFF BELOW FALSE DECK. D.F.T. PER

COAT IS 125-150 MICRONS

GENERAL STORE NO. 3 4L 57.1 ST DECK C207 See Remarks OFF WHITE BELOW FALSE DECK. D.F.T. PER

COAT IS 125-150 MICRONSGENERAL STORE NO. 3 4L 78.0 DECKHEAD C212 36 36 C061 30 30 WHITE 27925 PART INSULATION SEE NOTE 4GENERAL STORE NO. 3 4L 53.1 FORWARD C212 36 36 C061 30 30 WHITE 27925GENERAL STORE NO. 3 4L 21.3 AFT C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925GENERAL STORE NO. 3 4L 24.4 PORT C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925GENERAL STORE NO. 3 4L 24.4 STBD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925GENERAL STORE NO. 3 4L 45.2 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480 ABOVE BOOT TOP

EMERGENCY FIRE PUMP ROOM 4LA0 11.7 ST DECK C207 See Remarks BUFF BELOW FALSE DECK. D.F.T. PER

COAT IS 125-150 MICRONS

EMERGENCY FIRE PUMP ROOM 4LA0 11.7 ST DECK C207 See Remarks OFF WHITE BELOW FALSE DECK. D.F.T. PER

COAT IS 125-150 MICRONSEMERGENCY FIRE PUMP ROOM 4LA0 12.6 DECKHEAD C212 36 36 NOTE 4 C061 30 30 WHITE 27925 PART INSULATIONEMERGENCY FIRE PUMP ROOM 4LA0 7.1 FORWARD C212 36 36 C061 30 30 WHITE 27925EMERGENCY FIRE PUMP ROOM 4LA0 7.1 AFT C212 36 36 C061 30 30 WHITE 27925EMERGENCY FIRE PUMP ROOM 4LA0 9.8 PORT C212 36 36 C061 30 30 WHITE 27925EMERGENCY FIRE PUMP ROOM 4LA0 9.8 STBD C212 36 36 C061 30 30 WHITE 27925

VOID 4MA 188.6 ALL INTERIOR SURFACES C207 See

Remarks BUFF D.F.T. PER COAT IS 125-150 ICRONS

VOID 4MA 188.6 ALL INTERIOR SURFACES C207 See

Remarks OFF WHITE D.F.T. PER COAT IS 125-150 ICRONS

VOID 4MA 70.0 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480 ABOVE BOOT TOP

TOWED ARRAY/TORPEDO DECOY DRAIN TANK 4MZ 121.4 ALL INTERIOR SURFACES C207 See

Remarks BUFF D.F.T. PER COAT IS 125-150 ICRONS

TOWED ARRAY/TORPEDO DECOY DRAIN TANK 4MZ 121.4 ALL INTERIOR SURFACES C207 See

Remarks OFF WHITE D.F.T. PER COAT IS 125-150 ICRONS


Primer

DCZ Area M2

Surface1st Coat

µm


Name

Remarks

Rev: C


µm2nd Coat

µm


Finisher


µm3rd Coat

µm1st Coat

µm

TOWED ARRAY/TORPEDO DECOY DRAIN TANK 4MZ 40.6 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480 ABOVE BOOT TOP

SPIRIT & TOBACCO STORE 3BZ 14.3 ST DECK C413 125-150 DK COVERINGSPIRIT & TOBACCO STORE 3BZ 21.7 DECKHEAD C212 36 36 NOTE 4 C061 30 30 WHITE 27925 PART INSULATIONSPIRIT & TOBACCO STORE 3BZ 16.1 FORWARD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925SPIRIT & TOBACCO STORE 3BZ 19.4 AFT C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925SPIRIT & TOBACCO STORE 3BZ 7.5 PORT C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925SPIRIT & TOBACCO STORE 3BZ 7.5 STBD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925SPIRIT & TOBACCO STORE 3BZ 15.0 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480 ABOVE BOOT TOPSPIRIT & TOBACCO STORE 3BZ 14.1 OTHERS C061 30 30 GREY 16076 DADO 900mm HIGH.MESS NO. 7 3CA 34.3 ST DECK C413 125-150 DK COVERINGMESS NO. 7 3CA 49.2 DECKHEAD C212 36 36 NOTE 4 C061 30 30 WHITE 27925 PART INSULATIONMESS NO. 7 3CA 19.4 FORWARD C212 36 36 C061 30 30 GREY 27886MESS NO. 7 3CA 31.4 AFT C061 30 30 GREY 27886 JOINER BULKHEADMESS NO. 7 3CA 17.5 PORT C212 36 36 INSULATION NOTE 4 C061 30 30 GREY 27886MESS NO. 7 3CA 10.9 STBD C212 36 36 INSULATION NOTE 4 C061 30 30 GREY 27886MESS NO. 7 3CA 28.4 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480MESS NO. 8 3CB0 35.8 ST DECK C413 125-150 DK COVERINGMESS NO. 8 3CB0 47.1 DECKHEAD C212 36 36 NOTE 4 C061 30 30 WHITE 27925 PART INSULATIONMESS NO. 8 3CB0 12.6 FORWARD C061 30 30 GREY 27875 JOINER BULKHEADMESS NO. 8 3CB0 13.4 AFT C212 36 36 C061 30 30 GREY 27875

MESS NO. 8 3CB0 24.9 PORT C212 36 36 NOTE 4 C061 30 30 GREY 27875 PART INSULATION. CLEAR OF JOINER BULKHEAD.

MESS NO. 8 3CB0 21.4 STBD C212 36 36 INSULATION NOTE 4 C061 30 30 GREY 27875MESS NO. 8 3CB0 21.4 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480

CLEANING GEAR LOCKER 3CB2 1.1 ST DECK TRAFFIC C413 125-150 C200 750-1000 GREY 36076

CLEANING GEAR LOCKER 3CB2 1.7 ST DECK NON-TRAFFIC 76 C061 30 30 GREY 16076

CLEANING GEAR LOCKER 3CB2 5.6 DECKHEAD C212 36 36 NOTE 4 C061 30 30 WHITE 513-201 PART INSULATIONCLEANING GEAR LOCKER 3CB2 6.4 FORWARD C061 30 30 WHITE 513-201 JOINER BULKHEADCLEANING GEAR LOCKER 3CB2 7.2 AFT C061 30 30 WHITE 513-201 JOINER BULKHEAD

CLEANING GEAR LOCKER 3CB2 5.0 PORT C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 513-201

CLEANING GEAR LOCKER 3CB2 4.9 STBD C061 30 30 WHITE 513-201 JOINER BULKHEAD

CLEANING GEAR LOCKER 3CB2 5 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480

CLEANING GEAR LOCKER 3CB2 1.0 OTHERS C061 30 30 GREY 16076 DADO 150mm HIGH

CREWS WP & HEADS NO. 2 3CZ0 11.2 ST DECK C413 125-150 DK COVERING

CREWS WP & HEADS NO. 2 3CZ0 11.2 DECKHEAD C212 36 36 C061 30 30 WHITE 27925

CREWS WP & HEADS NO. 2 3CZ0 10.3 FORWARD C212 36 36 NOTE 4 C061 30 30 GREY 27880 PART INSULATION

CREWS WP & HEADS NO. 2 3CZ0 10.1 AFT C212 36 36 C061 30 30 GREY 27880

CREWS WP & HEADS NO. 2 3CZ0 6.3 PORT C061 30 30 GREY 27880 JOINER BULKHEAD

CREWS WP & HEADS NO. 2 3CZ0 6.9 STBD C212 36 36 C061 30 30 GREY 27880

CREWS WP & HEADS NO. 2 3CZ0 4.1 OTHERS C212 36 36 C061 30 30 GREY 27880 SHOWER PARTITIONS


Primer

DCZ Area M2

Surface1st Coat

µm


Name

Remarks

Rev: C


µm2nd Coat

µm


Finisher


µm3rd Coat

µm1st Coat

µm

CREWS WP & HEADS NO. 2 3CZ0 6.6 OTHERS C061 30 30 GREY 27880 W.C. PARTITIONS

LOBBY 3CZ2 15.5 ST DECK C413 125-150 DK COVERINGLOBBY 3CZ2 20.8 DECKHEAD C212 36 36 NOTE 4 C061 30 30 WHITE 27925 PART INSULATIONLOBBY 3CZ2 19.8 FORWARD C061 30 30 GREY 27880 JOINER BULKHEADLOBBY 3CZ2 7.2 AFT C212 36 36 C061 30 30 GREY 27880LOBBY 3CZ2 9.9 PORT C212 36 36 INSULATION NOTE 4 C061 30 30 GREY 27880

LOBBY 3CZ2 24.4 STBD C212 36 36 NOTE 4 C061 30 30 GREY 27880 PART INSULATION. CLEAR OF JOINER BULKHEAD

LOBBY 3CZ2 9.9 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480LOBBY 3CZ2 3.4 OTHERS C061 30 30 GREY 16076 DADO 150mm HIGH

COMMAND & CONTROL EQUIPMENT RM NO.3 3DA0 3.2 ST DECK TRAFFIC C413 125-150 C200 750-1000 GREY 36076

COMMAND & CONTROL EQUIPMENT RM NO.3 3DA0 31.7 ST DECK NON TRAFFIC

C413 AND C045 C061 OR C177 30 30 GREY 16076

COMMAND & CONTROL EQUIPMENT RM NO.3 3DA0 34.2 DECKHEAD C212 36 36 NOTE 4 C061 30 30 WHITE 27925 PART INSULATIONCOMMAND & CONTROL EQUIPMENT RM NO.3 3DA0 22.4 FORWARD C212 36 36 C061 30 30 WHITE 27925COMMAND & CONTROL EQUIPMENT RM NO.3 3DA0 22.4 AFT C212 36 36 C061 30 30 WHITE 27925COMMAND & CONTROL EQUIPMENT RM NO.3 3DA0 10.8 PORT C212 36 36 C061 30 30 WHITE 27925COMMAND & CONTROL EQUIPMENT RM NO.3 3DA0 10.8 STBD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925COMMAND & CONTROL EQUIPMENT RM NO.3 3DA0 10.8 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480PASSAGEWAY 3DA2 43.0 ST DECK C413 125-150 DK COVERINGPASSAGEWAY 3DA2 46.4 DECKHEAD C212 36 36 NOTE 4 C061 30 30 WHITE 27925 PART INSULATIONPASSAGEWAY 3DA2 18.3 FORWARD C212 36 36 C061 30 30 GREY 26132PASSAGEWAY 3DA2 5.7 AFT C212 36 36 C061 30 30 GREY 26132PASSAGEWAY 3DA2 46.2 PORT C212 36 36 INSULATION NOTE 4 C061 30 30 GREY 26132PASSAGEWAY 3DA2 42.8 STBD C212 36 36 C061 30 30 GREY 26132 CLEAR OF JOINER BHDPASSAGEWAY 3DA2 46.2 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480PASSAGEWAY 3DA2 7.5 OTHERS C061 30 30 WHITE 16076 DADO (150mm HIGH)DISH WASHING COMPARTMENT 3DY0 5.7 ST DECK C413 125-150 DK COVERINGDISH WASHING COMPARTMENT 3DY0 6.2 DECKHEAD C212 36 36 C061 30 30 WHITE 27925DISH WASHING COMPARTMENT 3DY0 8.3 FORWARD C061 30 30 WHITE 27925 JOINER BULKHEADDISH WASHING COMPARTMENT 3DY0 8.3 AFT C061 30 30 WHITE 27925 JOINER BULKHEADDISH WASHING COMPARTMENT 3DY0 4.5 PORT C061 30 30 WHITE 27925 JOINER BULKHEADDISH WASHING COMPARTMENT 3DY0 4.5 STBD C061 30 30 WHITE 27925 JOINER BULKHEADCREWS LOUNGE (CASUALTY CLEARING STATION) 3DZ0 45.5 ST DECK C413 125-150 DK COVERING

CREWS LOUNGE (CASUALTY CLEARING STATION) 3DZ0 49.1 DECKHEAD C212 36 36 C061 30 30 WHITE 27925

CREWS LOUNGE (CASUALTY CLEARING STATION) 3DZ0 14.3 FORWARD C212 36 36 C061 30 30 GREY 27886

CREWS LOUNGE (CASUALTY CLEARING STATION) 3DZ0 14.3 AFT C061 30 30 GREY 27886 JOINER BULKHEAD

CREWS LOUNGE (CASUALTY CLEARING STATION) 3DZ0 19.8 PORT C061 30 30 GREY 27886 JOINER BULKHEAD

CREWS LOUNGE (CASUALTY CLEARING STATION) 3DZ0 9.9 STBD C061 30 30 GREY 27886 JOINER BULKHEAD

CREWS CAFETERIA 3DZ0 59.1 ST DECK C413 125-150 DK COVERINGCREWS CAFETERIA 3DZ0 63.8 DECKHEAD C212 36 36 NOTE 4 C061 30 30 WHITE 27925 PART INSULATIONCREWS CAFETERIA 3DZ0 18.1 FORWARD C212 36 36 1-GP-52M 30 30 GREY 27880 JOINER BULKHEADCREWS CAFETERIA 3DZ0 18.1 AFT C212 36 36 1-GP-52M 30 30 GREY 27880 LININGCREWS CAFETERIA 3DZ0 32.5 PORT 1-GP-52M 30 30 GREY 27880 JOINER BULKHEADCREWS CAFETERIA 3DZ0 35.1 STBD C212 36 36 INSULATION 1-GP-52M 30 30 GREY 27880 LINING


Primer

DCZ Area M2

Surface1st Coat

µm


Name

Remarks

Rev: C


µm2nd Coat

µm


Finisher


µm3rd Coat

µm1st Coat

µm

CREWS CAFETERIA 3DZ0 35.1 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480CREWS LOUNGE HEADS 3DZ2 4.4 ST DECK C413 125-150 DK COVERINGCREWS LOUNGE HEADS 3DZ2 4.8 DECKHEAD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925CREWS LOUNGE HEADS 3DZ2 1.5 FORWARD C061 30 30 GREY 27880 JOINER BULKHEADCREWS LOUNGE HEADS 3DZ2 2.6 AFT C212 36 36 C061 30 30 GREY 27880

CREWS LOUNGE HEADS 3DZ2 7.5 PORT C212 36 36 INSULATION NOTE 4 C061 30 30 GREY 27880

CLEAR OF FIBREGLASS LINING. FOR FFH 330,331,332,334 & 335 APPLY 1 COAT 38 µm OF C021 TO THE DOUBLE LAYER OF FIBREGLASS, COLOUR TO BE GREY 27880. SEE NOTE 18 FOR FFH 333, 336 TO 341.

CREWS LOUNGE HEADS 3DZ2 5.5 STBD C061 30 30 GREY 27880 JOINER BULKHEADCREWS LOUNGE HEADS 3DZ2 7.5 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480CREWS LOUNGE HEADS 3DZ2 2.5 OTHERS C061 30 30 GREY 101-202 WC PARTITIONSPASSAGEWAY(PORT) 3EA0 19.5 ST DECK C413 125-150 DK COVERINGPASSAGEWAY(PORT) 3EA0 21.1 DECKHEAD C212 36 36 C061 30 30 WHITE 27925PASSAGEWAY(PORT) 3EA0 12.3 FORWARD C212 36 36 C061 30 30 GREY 27880PASSAGEWAY(PORT) 3EA0 12.3 AFT C212 36 36 C061 30 30 GREY 27880PASSAGEWAY(PORT) 3EA0 26.5 PORT C212 36 36 C061 30 30 GREY 27880PASSAGEWAY(PORT) 3EA0 26.5 STBD C212 36 36 C061 30 30 GREY 27880 CLEAR OF JOINER BULKHEADPASSAGEWAY(PORT) 3EA0 4.4 OTHERS C061 30 30 GREY 16076 DADO (150mm HIGH)PASSAGEWAY(FORWARD) 3EA0 7.9 ST DECK C413 125-150 DK COVERINGPASSAGEWAY(FORWARD) 3EA0 8.5 DECKHEAD C212 36 36 C061 30 30 WHITE 27925PASSAGEWAY(FORWARD) 3EA0 21.4 FORWARD C212 36 36 C061 30 30 GREY 27880PASSAGEWAY(FORWARD) 3EA0 19.8 AFT C061 30 30 GREY 27880 JOINER BULKHEADPASSAGEWAY(FORWARD) 3EA0 2.6 PORT C212 36 36 C061 30 30 GREY 27880PASSAGEWAY(FORWARD) 3EA0 2.4 STBD C061 30 30 GREY 27880 JOINER BULKHEADPASSAGEWAY(FORWARD) 3EA0 2.7 OTHERS C061 30 30 GREY 16076 DADO (150mm HIGH)DRY GOODS STORAGE 3EA1 2.8 ST DECK C413 125-150 DK COVERINGDRY GOODS STORAGE 3EA1 4.2 DECKHEAD C212 36 36 NOTE 4 C061 30 30 WHITE 27925 PART INSULATIONDRY GOODS STORAGE 3EA1 5.4 FORWARD C212 36 36 C061 30 30 WHITE 27925DRY GOODS STORAGE 3EA1 5.2 AFT C061 30 30 WHITE 27925 JOINER BULKHEADDRY GOODS STORAGE 3EA1 4.9 PORT C061 30 30 WHITE 27925 JOINER BULKHEADDRY GOODS STORAGE 3EA1 5.3 STBD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925DRY GOODS STORAGE 3EA1 5.3 SHELL EXT 76 C061 30 30 30 GREY 26480

FORWARD A/C PLANT 3EA2 11.3 ST DECK TRAFFIC C413 125-150 C200 750-1000 GREY 36076

FORWARD A/C PLANT 3EA2 12.6 ST DECK NON TRAFFIC

C413 AND C045 C061 OR C177 30 30 GREY 16076

FORWARD A/C PLANT 3EA2 31.8 DECKHEAD C212 36 36 INSULATION C061 30 30 WHITE 27925FORWARD A/C PLANT 3EA2 7.6 FORWARD C212 36 36 INSULATION NOTE 5 WHITE 27925FORWARD A/C PLANT 3EA2 8.3 AFT C212 36 36 C061 30 30 WHITE 27925FORWARD A/C PLANT 3EA2 26.5 PORT C212 36 36 INSULATION NOTE 5 WHITE 27925FORWARD A/C PLANT 3EA2 26.5 STBD C212 36 36 INSULATION NOTE 5 WHITE 27925FORWARD A/C PLANT 3EA2 26.5 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480

FORWARD A/C PLANT 3EA2 22.4 OTHERS C061 30 30 GREY 16076 DADO (900mm HIGH) EXCEPT OVER PERFORATED METAL.

DUMB WAITER TRUNK 3EB1 30.1 ALL INTERIOR SURFACES C207 See


DUMB WAITER TRUNK 3EB1 30.1 ALL INTERIOR SURFACES C207 See

Remarks OFF WHITE D.F.T. PER COAT IS 125-150 MICRONS

COOKS OFFICE 3EY1 3.3 ST DECK C413 125-150 DK COVERINGCOOKS OFFICE 3EY1 3.6 DECKHEAD C212 36 36 C061 30 30 WHITE 27925


Primer

DCZ Area M2

Surface1st Coat

µm


Name

Remarks

Rev: C


µm2nd Coat

µm


Finisher


µm3rd Coat

µm1st Coat

µm

COOKS OFFICE 3EY1 5.8 FORWARD C212 36 36 C061 30 30 GREEN 24585COOKS OFFICE 3EY1 5.4 AFT C061 30 30 GREEN 24585 JOINER BULKHEADCOOKS OFFICE 3EY1 3.7 PORT C061 30 30 GREEN 24585 JOINER BULKHEADCOOKS OFFICE 3EY1 4.0 STBD C212 36 36 C061 30 30 GREEN 24585LOBBY 3EY1 9.9 ST DECK C413 125-150 DK COVERINGLOBBY 3EY1 10.7 DECKHEAD C212 36 36 C061 30 30 WHITE 27925LOBBY 3EY1 11.7 FORWARD C212 36 36 C061 30 30 GREY 27880LOBBY 3EY1 11.7 AFT C212 36 36 C061 30 30 GREY 27880LOBBY 3EY1 8.0 PORT C212 36 36 C061 30 30 GREY 27880LOBBY 3EY1 8.0 STBD C212 36 36 C061 30 30 GREY 27880LOBBY 3EY1 2.2 OTHERS C061 30 30 GREY 16076 DADO (150mm HIGH)FAMR ACCESS 3EY2 2.2 ST DECK C413 125-150 C200 750-1000 GREY 36076FAMR ACCESS 3EY2 2.4 DECKHEAD C212 36 36 INSULATION C061 30 30 WHITE 27925FAMR ACCESS 3EY2 2.9 FORWARD C212 36 36 INSULATION NOTE 5 C061 30 30 GREY 27880FAMR ACCESS 3EY2 2.9 AFT C212 36 36 INSULATION NOTE 5 C061 30 30 GREY 27880FAMR ACCESS 3EY2 5.2 PORT C212 36 36 INSULATION NOTE 5 C061 30 30 GREY 27880FAMR ACCESS 3EY2 5.2 STBD C212 36 36 INSULATION NOTE 5 C061 30 30 GREY 27880GALLEY 3EZ1 57.2 ST DECK C413 125-150 DKCOVERINGGALLEY 3EZ1 66.4 DECKHEAD C212 36 36 NOTE 4 C061 30 30 WHITE 27925 PART INSULATIONGALLEY 3EZ1 26.1 FORWARD C061 30 30 WHITE 27925 JOINER BULKHEADGALLEY 3EZ1 38.8 AFT C212 36 36 C061 30 30 WHITE 27925GALLEY 3EZ1 26.5 PORT C212 36 36 C061 30 30 WHITE 27925

GALLEY 3EZ1 26.5 STBD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925

CLEAR OF FIBREGLASS LINING. APPLY 1 COAT 38 µm OF 1-GP-146M TO THE DOUBLE LAYER OF FIBREGLASS, COLOUR TO BE WHITE.

GALLEY 3EZ1 21.2 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480

GALLEY A/C PLANT 3FA1 5.0 ST DECK TRAFFIC C413 125-150 C200 750-1000 GREY 36076

GALLEY A/C PLANT 3FA1 4.7 ST DECK NON TRAFFIC

C413 AND C045 C061 OR C177 30 30 GREY 16076

GALLEY A/C PLANT 3FA1 10.5 DECKHEAD C212 36 36 INSULATION C061 30 30 WHITE 27925GALLEY A/C PLANT 3FA1 5.8 FORWARD C212 36 36 INSULATION NOTE 5 WHITE 27925GALLEY A/C PLANT 3FA1 5.8 AFT C212 36 36 C061 30 30 WHITE 27925GALLEY A/C PLANT 3FA1 13.3 PORT C212 36 36 INSULATION NOTE 5 WHITE 27925GALLEY A/C PLANT 3FA1 13.3 STBD C212 36 36 INSULATION NOTE 5 WHITE 27925GALLEY A/C PLANT 3FA1 13.0 OTHERS C061 30 30 GREY 16076 DADO (900mm HIGH)PASSAGEWAY 3FA2 38.2 ST DECK C413 125-150 DK COVERINGPASSAGEWAY 3FA2 41.3 DECKHEAD C212 36 36 NOTE 4 C061 30 30 WHITE 27925 PART INSULATIONPASSAGEWAY 3FA2 30.5 FORWARD C212 36 36 C061 30 30 GREY 27880PASSAGEWAY 3FA2 30.5 AFT C212 36 36 C061 30 30 GREY 27880PASSAGEWAY 3FA2 41.0 PORT C061 30 30 GREY 27880 JOINER BULKHEADPASSAGEWAY 3FA2 46.9 STBD C212 36 36 C061 30 30 GREY 27880

PASSAGEWAY 3FA2 9.2 OTHERS C061 30 30 GREY 16076 DADO (900mm HIGH) EXCEPT OVER PERFORATED METAL.

CHIEF & PETTY OFFICERS SERVERY NO. 3 DECK 3FA3 11.6 ST DECK C413 125-150 DK COVERING

CHIEF & PETTY OFFICERS SERVERY NO. 3 DECK 3FA3 14.8 DECKHEAD C212 36 36 NOTE 4 C061 30 30 WHITE 27925 PART INSULATION

CHIEF & PETTY OFFICERS SERVERY NO. 3 DECK 3FA3 9.3 FORWARD C212 36 36 C061 30 30 WHITE 27925

CHIEF & PETTY OFFICERS SERVERY NO. 3 DECK 3FA3 8.9 AFT C061 30 30 WHITE 27925 JOINER BULKHEAD


Primer

DCZ Area M2

Surface1st Coat

µm


Name

Remarks

Rev: C


µm2nd Coat

µm


Finisher


µm3rd Coat

µm1st Coat

µm

CHIEF & PETTY OFFICERS SERVERY NO. 3 DECK 3FA3 14.6 PORT C212 36 36 C061 30 30 WHITE 27925

CHIEF & PETTY OFFICERS SERVERY NO. 3 DECK 3FA3 14.6 STBD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925

CHIEF & PETTY OFFICERS SERVERY NO. 3 DECK 3FA3 14.6 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480

MEDICAL STORE 3FA4 2.5 ST DECK TRAFFIC C413 125-150 C200 750-1000 GREY 36076

MEDICAL STORE 3FA4 4.3 ST DECK NON TRAFFIC

C413 AND C045 C061 OR C177 30 30 GREY 16076

MEDICAL STORE 3FA4 8.5 DECKHEAD C212 36 36 NOTE 4 C061 30 30 WHITE 27925 PART INSULATIONMEDICAL STORE 3FA4 8.3 FORWARD C212 36 36 C061 30 30 WHITE 27925MEDICAL STORE 3FA4 8.4 AFT C212 36 36 C061 30 30 WHITE 27925MEDICAL STORE 3FA4 6.9 PORT C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925MEDICAL STORE 3FA4 6.9 STBD C212 36 36 C061 30 30 WHITE 27925MEDICAL STORE 3FA4 6.9 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480MEDICAL STORE 3FA4 9.6 OTHERS C061 30 30 GREY 16076 DADO (900mm HIGH)

ELECTRICAL WORKSHOP 3FB2 3.3 ST DECK TRAFFIC C413 125-150 C200 750-1000 GREY 36076

ELECTRICAL WORKSHOP 3FB2 4.9 ST DECK NON TRAFFIC

C413 AND C045 C061 OR C177 30 30 GREY 16076

ELECTRICAL WORKSHOP 3FB2 10.0 DECKHEAD C212 36 36 NOTE 4 C061 30 30 WHITE 27925 PART INSULATIONELECTRICAL WORKSHOP 3FB2 8.4 FORWARD C212 36 36 C061 30 30 WHITE 27925 JOINER BULKHEADELECTRICAL WORKSHOP 3FB2 7.9 AFT C061 30 30 WHITE 27925 JOINER BULKHEADELECTRICAL WORKSHOP 3FB2 7.7 PORT C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925ELECTRICAL WORKSHOP 3FB2 7.1 STBD C061 30 30 WHITE 27925 JOINER BULKHEADELECTRICAL WORKSHOP 3FB2 7.7 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480ELECTRICAL WORKSHOP 3FB2 10.3 OTHERS C061 30 30 GREY 16076 DADO (900mm HIGH)

MECHANICAL WORKSHOP 3FC2 7.9 ST DECK TRAFFIC C413 125-150 C200 750-1000 GREY 36076

MECHANICAL WORKSHOP 3FC2 10.9 ST DECK NON TRAFFIC

C413 AND C045 C061 OR C177 30 30 GREY 16076

MECHANICAL WORKSHOP 3FC2 22.8 DECKHEAD C212 36 36 NOTE 4 C061 30 30 WHITE 27925 PART INSULATIONMECHANICAL WORKSHOP 3FC2 8.7 FORWARD C061 30 30 WHITE 27925 JOINER BULKHEADMECHANICAL WORKSHOP 3FC2 8.8 AFT C061 30 30 WHITE 27925 JOINER BULKHEADMECHANICAL WORKSHOP 3FC2 17.8 PORT C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925MECHANICAL WORKSHOP 3FC2 16.5 STBD C061 30 30 WHITE 27925 JOINER BULKHEADMECHANICAL WORKSHOP 3FC2 17.8 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480MECHANICAL WORKSHOP 3FC2 18.0 OTHERS C061 30 30 GREY 16076 DADO (900mm HIGH)

TOOL CRIB 3FY2 1.9 ST DECK TRAFFIC C413 125-150 C200 750-1000 GREY 36076

TOOL CRIB 3FY2 3.5 ST DECK NON TRAFFIC

C413 AND C045 C061 OR C177 30 30 GREY 16076

TOOL CRIB 3FY2 6.8 DECKHEAD C212 36 36 NOTE 4 C061 30 30 WHITE 27925 PART INSULATIONTOOL CRIB 3FY2 5.5 FORWARD C061 30 30 WHITE 27925 JOINER BULKHEADTOOL CRIB 3FY2 5.6 AFT C061 30 30 WHITE 27925 JOINER BULKHEADTOOL CRIB 3FY2 7.2 PORT C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925TOOL CRIB 3FY2 6.8 STBD C061 30 30 WHITE 27925 JOINER BULKHEADTOOL CRIB 3FY2 7.2 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480TOOL CRIB 3FY2 8.5 OTHERS C061 30 30 GREY 16076 DADO (900mm HIGH)CHIEF & PETTY OFFICERS LOUNGE 3FZ0 36.3 ST DECK C413 125-150 DK COVERINGCHIEF & PETTY OFFICERS LOUNGE 3FZ0 39.2 DECKHEAD C212 36 36 C061 30 30 WHITE 27925CHIEF & PETTY OFFICERS LOUNGE 3FZ0 17.5 FORWARD C212 36 36 C061 30 30 GREY 27886


Primer

DCZ Area M2

Surface1st Coat

µm


Name

Remarks

Rev: C


µm2nd Coat

µm


Finisher


µm3rd Coat

µm1st Coat

µm

CHIEF & PETTY OFFICERS LOUNGE 3FZ0 17.5 AFT C212 36 36 C061 30 30 GREY 27886 LININGCHIEF & PETTY OFFICERS LOUNGE 3FZ0 15.9 PORT C212 36 36 C061 30 30 GREY 27886 LININGCHIEF & PETTY OFFICERS LOUNGE 3FZ0 15.9 STBD C212 36 36 C061 30 30 GREY 27886 LININGCHIEF & PETTY OFFICERS DINING ROOM NO. 3 DECK 3FZ1 46.6 ST DECK C413 125-150 DK COVERING

CHIEF & PETTY OFFICERS DINING ROOM NO. 3 DECK 3FZ1 54.5 DECKHEAD C212 36 36 NOTE 4 C061 30 30 WHITE 27925 PART INSULATION

CHIEF & PETTY OFFICERS DINING ROOM NO. 3 DECK 3FZ1 11.1 FORWARD C061 30 30 GREY 27880 JOINER BULKHEAD

CHIEF & PETTY OFFICERS DINING ROOM NO. 3 DECK 3FZ1 12.2 AFT C212 36 36 C061 30 30 GREY 27880 LINING

CHIEF & PETTY OFFICERS DINING ROOM NO. 3 DECK 3FZ1 31.8 PORT C212 36 36 C061 30 30 GREY 27880

CHIEF & PETTY OFFICERS DINING ROOM NO. 3 DECK 3FZ1 31.8 STBD C212 36 36 INSULATION C061 30 30 GREY 27880 LINING

CHIEF & PETTY OFFICERS DINING ROOM NO. 3 DECK 3FZ1 30.3 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480

FER ACCESS 3FZ2 1.7 ST DECK TRAFFIC C413 125-150 C200 750-1000 GREY 36076

FER ACCESS 3FZ2 0.7 ST DECK NON TRAFFIC

C413 AND C045 C061 OR C177 30 30 GREY 16076

FER ACCESS 3FZ2 3.6 DECKHEAD C212 36 36 C061 30 30 WHITE 27925FER ACCESS 3FZ2 4.3 FORWARD C212 36 36 INSULATION NOTE 5 GREY 27880FER ACCESS 3FZ2 4.3 AFT C212 36 36 INSULATION NOTE 5 GREY 27880FER ACCESS 3FZ2 5.3 PORT C212 36 36 INSULATION NOTE 5 GREY 27880FER ACCESS 3FZ2 5.3 STBD C212 36 36 INSULATION NOTE 5 GREY 27880C & PO'S LOUNGE HEADS 3FZ4 5.6 ST DECK C413 125-150 DK COVERINGC & PO'S LOUNGE HEADS 3FZ4 6.7 DECKHEAD C212 36 36 NOTE 4 PART INSULATIONC & PO'S LOUNGE HEADS 3FZ4 8.0 FORWARD C061 30 30 GREY 27880 JOINER BULKHEADC & PO'S LOUNGE HEADS 3FZ4 8.6 AFT C212 36 36 C061 30 30 GREY 27880

C & PO'S LOUNGE HEADS 3FZ4 5.3 PORT C212 36 36 INSULATION NOTE 4 C061 30 30 GREY 27880

CLEAR OF FIBREGLASS LINING. FOR FFH 330,331,332,334 & 335 APPLY 1 COAT 38 µm OF 1-GP-146M TO THE DOUBLE LAYER OF FIBREGLASS, COLOUR TO BE GREY 101-202. SEE NOTE 18 FOR FFH 333, 336 TO 341.

C & PO'S LOUNGE HEADS 3FZ4 4.9 STBD C061 30 30 GREY 27880 JOINER BULKHEADC & PO'S LOUNGE HEADS 3FZ4 5.3 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480C & PO'S LOUNGE HEADS 3FZ4 6.0 OTHERS C061 30 30 GREY 27880 W.C. PARTITIONS

DEGAUSSING EQUIPMENT ROOM 3GA1 8.3 ST DECK TRAFFIC C413 125-150 C200 750-1000 GREY 36076

DEGAUSSING EQUIPMENT ROOM 3GA1 8.0 ST DECK NON TRAFFIC

C413 AND C045 C061 OR C177 30 30 GREY 16076

DEGAUSSING EQUIPMENT ROOM 3GA1 19.9 DECKHEAD C212 36 36 INSULATION NOTE 5 WHITE 27925DEGAUSSING EQUIPMENT ROOM 3GA1 12.2 FORWARD C212 36 36 INSULATION NOTE 5 WHITE 27925DEGAUSSING EQUIPMENT ROOM 3GA1 12.2 AFT C212 36 36 INSULATION NOTE 5 WHITE 27925DEGAUSSING EQUIPMENT ROOM 3GA1 10.6 PORT C212 36 36 INSULATION NOTE 5 WHITE 27925DEGAUSSING EQUIPMENT ROOM 3GA1 10.6 STBD C212 36 36 INSULATION NOTE 5 WHITE 27925DEGAUSSING EQUIPMENT ROOM 3GA1 10.6 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480PASSAGEWAY 3GA2 19.4 ST DECK C413 125-150 DK COVERINGPASSAGEWAY 3GA2 20.9 DECKHEAD C212 36 36 NOTE 4 C061 30 30 WHITE 27925 PART INSULATIONPASSAGEWAY 3GA2 8.7 FORWARD C212 36 36 C061 30 30 GREY 27880


Primer

DCZ Area M2

Surface1st Coat

µm


Name

Remarks

Rev: C


µm2nd Coat

µm


Finisher


µm3rd Coat

µm1st Coat

µm

PASSAGEWAY 3GA2 8.7 AFT C212 36 36 C061 30 30 GREY 27880PASSAGEWAY 3GA2 24.5 PORT C061 30 30 GREY 27880 JOINER BULKHEADPASSAGEWAY 3GA2 26.5 STBD C212 36 36 C061 30 30 GREY 27880PASSAGEWAY 3GA2 3.4 OTHERS C061 30 30 GREY 16076 DADO (150mm HIGH)

CONTROL SYSTEMS WORKSHOP 3GA4 3.1 ST DECK TRAFFIC C413 125-150 C200 750-1000 GREY 36076

CONTROL SYSTEMS WORKSHOP 3GA4 2.5 ST DECK NON TRAFFIC

C413 AND C045 C061 OR C177 30 30 GREY 16076

CONTROL SYSTEMS WORKSHOP 3GA4 6.7 DECKHEAD C212 36 36 NOTE 4 C061 30 30 WHITE 27925 PART INSULATIONCONTROL SYSTEMS WORKSHOP 3GA4 8.7 FORWARD C212 36 36 C061 30 30 WHITE 27925CONTROL SYSTEMS WORKSHOP 3GA4 8.1 AFT C061 30 30 WHITE 27925 JOINER BULKHEADCONTROL SYSTEMS WORKSHOP 3GA4 5.3 PORT C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925CONTROL SYSTEMS WORKSHOP 3GA4 4.9 STBD C061 30 30 WHITE 27925 JOINER BULKHEADCONTROL SYSTEMS WORKSHOP 3GA4 5.3 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480CONTROL SYSTEMS WORKSHOP 3GA4 9.0 OTHERS C061 30 30 GREY 16076 DADO (900mm HIGH)AER ACCESS 3GB2 3.5 ST DECK C413 125-150 C200 750-1000 GREY 36076AER ACCESS 3GB2 4.3 DECKHEAD C212 36 36 C061 30 30 WHITE 27925AER ACCESS 3GB2 4.3 FORWARD C212 36 36 INSULATION NOTE 5 GREY 27880AER ACCESS 3GB2 4.3 AFT C212 36 36 INSULATION NOTE 5 GREY 27880AER ACCESS 3GB2 6.4 PORT C212 36 36 INSULATION NOTE 5 GREY 27880AER ACCESS 3GB2 6.4 STBD C212 36 36 INSULATION NOTE 5 GREY 27880AER ACCESS 3GB2 1.2 OTHERS C061 30 30 GREY 16076 DADO (150mm HIGH)STORES OFFICE 3GB4 14.9 ST DECK C413 125-150 DK COVERINGSTORES OFFICE 3GB4 17.7 DECKHEAD C212 36 36 NOTE 4 C061 30 30 WHITE 27925 PART INSULATIONSTORES OFFICE 3GB4 8.1 FORWARD C061 30 30 GREEN 24585 JOINER BULKHEADSTORES OFFICE 3GB4 8.1 AFT C061 30 30 GREEN 24585 JOINER BULKHEADSTORES OFFICE 3GB4 13.2 PORT C212 36 36 INSULATION NOTE 4 C061 30 30 GREEN 24585STORES OFFICE 3GB4 12.2 STBD C061 30 30 GREEN 24585 JOINER BULKHEADSTORES OFFICE 3GB4 13.2 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480STORES OFFICE 3GB4 14.3 OTHERS C061 30 30 GREY 16076 DADO (900mm HIGH)CBRND HEADQUARTERS & MACHINERY CONTROL ROOM 3GZ0 55.4 ST DECK C413 125-150 NOTE 15 BELOW FALSE DECK

CBRND HEADQUARTERS & MACHINERY CONTROL ROOM 3GZ0 61.8 DECKHEAD C212 36 36 INSULATION NOTE 5 WHITE 27925

CBRND HEADQUARTERS & MACHINERY CONTROL ROOM 3GZ0 25.3 FORWARD C212 36 36 INSULATION NOTE 5 GREEN 17773

CBRND HEADQUARTERS & MACHINERY CONTROL ROOM 3GZ0 25.3 AFT C212 36 36 INSULATION NOTE 5 GREEN 17773

CBRND HEADQUARTERS & MACHINERY CONTROL ROOM 3GZ0 15.9 PORT C212 36 36 INSULATION NOTE 5 GREEN 17773

CBRND HEADQUARTERS & MACHINERY CONTROL ROOM 3GZ0 15.9 STBD C212 36 36 INSULATION NOTE 5 GREEN 17773

CBRND HEADQUARTERS & MACHINERY CONTROL ROOM 3GZ0 15.9 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480

COXSWAINS OFFICE 3GZ2 9.0 ST DECK C413 125-150 DKCOVERINGCOXSWAINS OFFICE 3GZ2 10.7 DECKHEAD C212 36 36 NOTE 4 C061 30 30 WHITE 27925 PART INSULATIONCOXSWAINS OFFICE 3GZ2 8.0 FORWARD C061 30 30 GREEN 24585 JOINER BULKHEADCOXSWAINS OFFICE 3GZ2 8.6 AFT C212 36 36 C061 30 30 GREEN 24585COXSWAINS OFFICE 3GZ2 8.0 PORT C212 36 36 INSULATION NOTE 4 C061 30 30 GREEN 24585COXSWAINS OFFICE 3GZ2 7.4 STBD C061 30 30 GREEN 24585 JOINER BULKHEADCOXSWAINS OFFICE 3GZ2 8.0 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480


Primer

DCZ Area M2

Surface1st Coat

µm


Name

Remarks

Rev: C


µm2nd Coat

µm


Finisher


µm3rd Coat

µm1st Coat

µm

AFTER SWITCHBOARD ROOM 3HA1 19.7 ST DECK TRAFFIC C413 125-150 C200 750-1000 GREY 36076

AFTER SWITCHBOARD ROOM 3HA1 8.9 ST DECK NON TRAFFIC

C413 AND C045 C061 OR C177 30 30 GREY 16076

AFTER SWITCHBOARD ROOM 3HA1 32.2 DECKHEAD C212 36 36 NOTE 4 C061 30 30 WHITE 27925 PART INSULATIONAFTER SWITCHBOARD ROOM 3HA1 20.8 FORWARD C212 36 36 C061 30 30 WHITE 27925AFTER SWITCHBOARD ROOM 3HA1 20.7 AFT C212 36 36 C061 30 30 WHITE 27925AFTER SWITCHBOARD ROOM 3HA1 10.6 PORT C212 36 36 C061 30 30 WHITE 27925AFTER SWITCHBOARD ROOM 3HA1 10.6 STBD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925AFTER SWITCHBOARD ROOM 3HA1 10.6 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480ADMINISTRATION OFFICE 3HA2 18.6 ST DECK C413 125-150 DK COVERINGADMINISTRATION OFFICE 3HA2 21.9 DECKHEAD C212 36 36 NOTE 4 C061 30 30 WHITE 27925 PART INSULATIONADMINISTRATION OFFICE 3HA2 10.3 FORWARD C212 36 36 C061 30 30 GREY 24585ADMINISTRATION OFFICE 3HA2 9.3 AFT C061 30 30 GREY 24585 JOINER BULKHEADADMINISTRATION OFFICE 3HA2 14.0 PORT C212 36 36 INSULATION NOTE 4 C061 30 30 GREY 24585ADMINISTRATION OFFICE 3HA2 13.0 STBD C061 30 30 GREY 24585 JOINER BULKHEADADMINISTRATION OFFICE 3HA2 14.0 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480AAMR ACCESS 3HB1 2.4 ST DECK C413 125-150 C200 750-1000 GREY 36076AAMR ACCESS 3HB1 3.5 DECKHEAD C212 36 36 C061 30 30 WHITE 27925AAMR ACCESS 3HB1 6.6 FORWARD C212 36 36 C061 30 30 GREY 27880AAMR ACCESS 3HB1 6.6 AFT C212 36 36 C061 30 30 GREY 27880AAMR ACCESS 3HB1 3.5 PORT C212 36 36 C061 30 30 GREY 27880AAMR ACCESS 3HB1 3.5 STBD C212 36 36 C061 30 30 GREY 27880AAMR ACCESS 3HB1 1.1 OTHERS C061 30 30 GREY 16076 DADO (150mm HIGH)PASSAGEWAY 3HZ0 31.0 ST DECK C413 125-150 DK COVERINGPASSAGEWAY 3HZ0 35.2 DECKHEAD C212 36 36 C061 30 30 WHITE 27925PASSAGEWAY 3HZ0 16.4 FORWARD C212 36 36 C061 30 30 GREY 27880PASSAGEWAY 3HZ0 16.4 AFT C212 36 36 C061 30 30 GREY 27880PASSAGEWAY 3HZ0 19.6 PORT C212 36 36 C061 30 30 GREY 27880PASSAGEWAY 3HZ0 21.2 STBD C212 36 36 C061 30 30 GREY 27880 CLEAR OF JOINER BULKHEADPASSAGEWAY 3HZ0 4.3 OTHERS C061 30 30 GREY 16076 DADO (150mm HIGH)CANTEEN 3HZ1 5.9 ST DECK C413 125-150 DK COVERINGCANTEEN 3HZ1 6.4 DECKHEAD C212 36 36 C061 30 30 WHITE 27925CANTEEN 3HZ1 5.8 FORWARD C212 36 36 C061 30 30 WHITE 27925CANTEEN 3HZ1 5.8 AFT C212 36 36 C061 30 30 WHITE 27925CANTEEN 3HZ1 6.6 PORT C061 30 30 WHITE 27925 JOINER BULKHEADCANTEEN 3HZ1 6.6 STBD C061 30 30 WHITE 27925 JOINER BULKHEADPAY OFFICE 3HZ2 10.2 ST DECK C413 125-150 DK COVERINGPAY OFFICE 3HZ2 11.0 DECKHEAD C212 36 36 NOTE 4 C061 30 30 WHITE 27925 PART INSULATIONPAY OFFICE 3HZ2 9.3 FORWARD C061 30 30 GREY 24585 JOINER BULKHEADPAY OFFICE 3HZ2 9.9 AFT C212 36 36 C061 30 30 GREY 24585PAY OFFICE 3HZ2 7.1 PORT C212 36 36 INSULATION NOTE 4 C061 30 30 GREY 24585PAY OFFICE 3HZ2 6.6 STBD C061 30 30 GREY 24585 JOINER BULKHEADPAY OFFICE 3HZ2 7.1 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480

CANTEEN STORE 3HZ3 5.9 ST DECK TRAFFIC C413 125-150 C200 750-1000 GREY 36076

CANTEEN STORE 3HZ3 6 ST DECK NON TRAFFIC

C413 AND C045 C061 OR C177 30 30 GREY 16076

CANTEEN STORE 3HZ3 14.3 DECKHEAD C212 36 36 NOTE 4 C061 30 30 WHITE 27925 PART INSULATIONCANTEEN STORE 3HZ3 9.1 FORWARD C212 36 36 C061 30 30 WHITE 27925CANTEEN STORE 3HZ3 9.0 AFT C212 36 36 C061 30 30 WHITE 27925


Primer

DCZ Area M2

Surface1st Coat

µm


Name

Remarks

Rev: C


µm2nd Coat

µm


Finisher


µm3rd Coat

µm1st Coat

µm

CANTEEN STORE 3HZ3 10.6 PORT C212 36 36 C061 30 30 WHITE 27925CANTEEN STORE 3HZ3 10.6 STBD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925CANTEEN STORE 3HZ3 10.6 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480CANTEEN STORE 3HZ3 12.7 OTHERS C061 30 30 GREY 16076 DADO (900mm HIGH)PO'S WP & HEADS NO. 2 3JA0 18.3 ST DECK C413 125-150 DK COVERINGPO'S WP & HEADS NO. 2 3JA0 19.8 DECKHEAD C212 36 36 C061 30 30 WHITE 27925PO'S WP & HEADS NO. 2 3JA0 16.2 FORWARD C212 36 36 C061 30 30 GREY 27880PO'S WP & HEADS NO. 2 3JA0 15.0 AFT C061 30 30 GREY 27880 JOINER BULKHEADPO'S WP & HEADS NO. 2 3JA0 7.3 PORT C061 30 30 GREY 27880 JOINER BULKHEADPO'S WP & HEADS NO. 2 3JA0 8.0 STBD C212 36 36 C061 30 30 GREY 27880PO'S WP & HEADS NO. 2 3JA0 8.8 OTHERS C212 36 36 C061 30 30 GREY 27880 SHOWER PARTITIONSPO'S WP & HEADS NO. 2 3JA0 34.2 OTHERS C061 30 30 GREY 27880 W.C. PARTITIONSMESS NO. 9 3JA1 16.1 ST DECK C413 125-150 DK COVERINGMESS NO. 9 3JA1 19.0 DECKHEAD C212 36 36 NOTE 4 C061 30 30 WHITE 27925 PART INSULATIONMESS NO. 9 3JA1 12.6 FORWARD C212 36 36 C061 30 30 GREY 27875MESS NO. 9 3JA1 11.4 AFT C061 30 30 GREY 27875 JOINER BULKHEADMESS NO. 9 3JA1 11.4 PORT C061 30 30 GREY 27875 CLEAR OF JOINER BULKHEADMESS NO. 9 3JA1 12.3 STBD C212 36 36 INSULATION NOTE 4 C061 30 30 GREY 27875MESS NO. 9 3JA1 11.4 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480PASSAGEWAY 3JA2 23.3 ST DECK C413 125-150 DK COVERINGPASSAGEWAY 3JA2 26.0 DECKHEAD C212 36 36 C061 30 30 WHITE 27925PASSAGEWAY 3JA2 18.6 FORWARD C212 36 36 C061 30 30 GREY 27880PASSAGEWAY 3JA2 18.6 AFT C212 36 36 C061 30 30 GREY 27880PASSAGEWAY 3JA2 22.1 PORT C061 30 30 GREY 27880 JOINER BULKHEADPASSAGEWAY 3JA2 22.1 STBD C061 30 30 GREY 27880 JOINER BULKHEADPASSAGEWAY 3JA2 4.8 OTHERS C061 30 30 GREY 16076 DADO (150mm HIGH)MESS NO. 10 3JA4 29.7 ST DECK C413 125-150 DKCOVERINGMESS NO. 10 3JA4 35.4 DECKHEAD C212 36 36 NOTE 4 C061 30 30 WHITE 27925 PART INSULATIONMESS NO. 10 3JA4 10.4 FORWARD C212 36 36 C061 30 30 GREY 27875MESS NO. 10 3JA4 9.7 AFT C212 36 36 C061 30 30 GREY 27875MESS NO. 10 3JA4 23.9 PORT C212 36 36 INSULATION NOTE 4 C061 30 30 GREY 27875MESS NO. 10 3JA4 22.1 STBD C061 30 30 GREY 27875 JOINER BULKHEADMESS NO. 10 3JA4 22.1 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480MESS NO. 12 3JZ0 14.2 ST DECK C413 125-150 DK COVERINGMESS NO. 12 3JZ0 15.3 DECKHEAD C212 36 36 NOTE 4 C061 30 30 WHITE 27925 PART INSULATIONMESS NO. 12 3JZ0 7.0 FORWARD C061 30 30 GREY 27875 JOINER BULKHEADMESS NO. 12 3JZ0 7.6 AFT C212 36 36 C061 30 30 GREY 27875MESS NO. 12 3JZ0 12.2 PORT C061 30 30 GREY 27875 JOINER BULKHEADMESS NO. 12 3JZ0 12.2 STBD C061 30 30 GREY 27875 JOINER BULKHEADMESS NO. 11 3JZ1 30.7 ST DECK C413 125-150 DK COVERINGMESS NO. 11 3JZ1 33.2 DECKHEAD C212 36 36 NOTE 4 C061 30 30 WHITE 27925 PART INSULATIONMESS NO. 11 3JZ1 16.6 FORWARD C061 30 30 GREY 27875 JOINER BULKHEADMESS NO. 11 3JZ1 17.7 AFT C212 36 36 C061 30 30 GREY 27875MESS NO. 11 3JZ1 12.2 PORT C061 30 30 GREY 27875 JOINER BULKHEADMESS NO. 11 3JZ1 13.2 STBD C212 36 36 INSULATION NOTE 4 C061 30 30 GREY 27875MESS NO. 11 3JZ1 10.7 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480MESS NO. 15 3KA0 47.8 ST DECK C413 125-150 DK COVERINGMESS NO. 15 3KA0 53.8 DECKHEAD C212 36 36 NOTE 4 C061 30 30 WHITE 27925 PART INSULATIONMESS NO. 15 3KA0 25.3 FORWARD C212 36 36 C061 30 30 GREY 27886MESS NO. 15 3KA0 22.9 AFT C061 30 30 GREY 27886 JOINER BULKHEAD


Primer

DCZ Area M2

Surface1st Coat

µm


Name

Remarks

Rev: C


µm2nd Coat

µm


Finisher


µm3rd Coat

µm1st Coat

µm

MESS NO. 15 3KA0 13.2 PORT C061 30 30 GREY 27886 JOINER BULKHEADMESS NO. 15 3KA0 15.2 STBD C212 36 36 INSULATION NOTE 4 C061 30 30 GREY 27886MESS NO. 15 3KA0 13.7 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480PASSAGEWAY 3KA2 17.1 ST DECK C413 125-150 DK COVERINGPASSAGEWAY 3KA2 19.4 DECKHEAD C212 36 36 C061 30 30 WHITE 27925PASSAGEWAY 3KA2 9.3 FORWARD C212 36 36 C061 30 30 GREY 27880PASSAGEWAY 3KA2 9.2 AFT C212 36 36 C061 30 30 GREY 27880PASSAGEWAY 3KA2 24.5 PORT C061 30 30 GREY 27880 JOINER BULKHEADPASSAGEWAY 3KA2 24.5 STBD C061 30 30 GREY 27880 JOINER BULKHEADPASSAGEWAY 3KA2 4.0 OTHERS C061 30 30 GREY 16076 DADO (150mm HIGH)MESS NO. 14 3KA4 22.6 ST DECK C413 125-150 DK COVERINGMESS NO. 14 3KA4 26.8 DECKHEAD C212 36 36 INSULATION NOTE 5 WHITE 27925MESS NO. 14 3KA4 11.1 FORWARD C212 36 36 C061 30 30 GREY 27886MESS NO. 14 3KA4 9.8 AFT C061 30 30 GREY 27886 JOINER BULKHEADMESS NO. 14 3KA4 16.4 PORT C212 36 36 INSULATION NOTE 4 C061 30 30 GREY 27886MESS NO. 14 3KA4 15.2 STBD C061 30 30 GREY 27886 JOINER BULKHEADMESS NO. 14 3KA4 15.2 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480MESS NO. 16 3KZ0 38.9 ST DECK C413 125-150 DK COVERINGMESS NO. 16 3KZ0 43.7 DECKHEAD C212 36 36 NOTE 4 C061 30 30 WHITE 27925 PART INSULATIONMESS NO. 16 3KZ0 22.9 FORWARD C061 30 30 GREY 27875 JOINER BULKHEADMESS NO. 16 3KZ0 24.3 AFT C212 36 36 C061 30 30 GREY 27875MESS NO. 16 3KZ0 10.8 PORT C061 30 30 GREY 27875 JOINER BULKHEADMESS NO. 16 3KZ0 11.7 STBD C212 36 36 INSULATION NOTE 4 C061 30 30 GREY 27875MESS NO. 16 3KZ0 10.8 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480CREWS HEADS NO. 3 3KZ2 12.7 ST DECK C413 125-150 DK COVERING GREY 27880CREWS HEADS NO. 3 3KZ2 15.3 DECKHEAD C212 36 36 NOTE 4 C061 30 30 WHITE 27925 PART INSULATIONCREWS HEADS NO. 3 3KZ2 9.8 FORWARD C061 30 30 GREY 27880 JOINER BULKHEADCREWS HEADS NO. 3 3KZ2 10.3 AFT C212 36 36 C061 30 30 GREY 27880

CREWS HEADS NO. 3 3KZ2 10.0 PORT C212 36 36 INSULATION NOTE 4 C061 30 30 GREY 27880


CREWS HEADS NO. 3 3KZ2 9.3 STBD C212 36 36 C061 30 30 GREY 27880 JOINER BULKHEADCREWS HEADS NO. 3 3KZ2 9.3 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480CREWS HEADS NO. 3 3KZ2 36.3 OTHERS C061 30 30 GREY 27880 W.C. PARTITIONSCREWS WASHPLACE NO. 3 3LA0 21.1 ST DECK C413 125-150 DK COVERING GREY 27880CREWS WASHPLACE NO. 3 3LA0 22.2 DECKHEAD C212 36 36 NOTE 4 C061 30 30 WHITE 27925 PART INSULATIONCREWS WASHPLACE NO. 3 3LA0 21.3 FORWARD C212 36 36 C061 30 30 GREY 27880CREWS WASHPLACE NO. 3 3LA0 19.3 AFT C212 36 36 C061 30 30 GREY 27880CREWS WASHPLACE NO. 3 3LA0 7.3 PORT C061 30 30 GREY 27880 JOINER BULKHEAD

CREWS WASHPLACE NO. 3 3LA0 8.0 STBD C212 36 36 INSULATION NOTE 4 C061 30 30 GREY 27880


CREWS WASHPLACE NO. 3 3LA0 7.4 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480CREWS WASHPLACE NO. 3 3LA0 22.8 OTHERS C212 36 36 C061 30 30 GREY 27880 SHOWER PARTITIONSPASSAGEWAY 3LA2 18.8 ST DECK C413 125-150 DK COVERINGPASSAGEWAY 3LA2 20.3 DECKHEAD C212 36 36 C061 30 30 WHITE 27925


Primer

DCZ Area M2

Surface1st Coat

µm


Name

Remarks

Rev: C


µm2nd Coat

µm


Finisher


µm3rd Coat

µm1st Coat

µm

PASSAGEWAY 3LA2 8.2 FORWARD C212 36 36 C061 30 30 GREY 27880PASSAGEWAY 3LA2 8.2 AFT C212 36 36 C061 30 30 GREY 27880PASSAGEWAY 3LA2 26.9 PORT C061 30 30 GREY 27880 JOINER BULKHEADPASSAGEWAY 3LA2 26.9 STBD C061 30 30 GREY 27880 JOINER BULKHEADPASSAGEWAY 3LA2 4.2 OTHERS C061 30 30 GREY 16076 DADO (150mm HIGH)MESS NO. 18 3LA4 34.6 ST DECK C413 125-150 DK COVERINGMESS NO. 18 3LA4 41.9 DECKHEAD C212 36 36 C061 30 30 WHITE 27925 PART INSULATION SEE NOTE 4MESS NO. 18 3LA4 14.7 FORWARD C212 36 36 C061 30 30 GREY 27875MESS NO. 18 3LA4 13.3 AFT C212 36 36 C061 30 30 GREY 27875MESS NO. 18 3LA4 29.2 PORT C212 36 36 INSULATION NOTE 4 C061 30 30 GREY 27875MESS NO. 18 3LA4 27.0 STBD C061 30 30 GREY 27875 JOINER BULKHEADMESS NO. 18 3LA4 27.0 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480MESS NO. 17 3LB0 33.7 ST DECK C413 125-150 DK COVERINGMESS NO. 17 3LB0 35.1 DECKHEAD C212 36 36 NOTE 4 C061 30 30 WHITE 27925 PART INSULATIONMESS NO. 17 3LB0 22.2 FORWARD C212 36 36 C061 30 30 GREY 27886MESS NO. 17 3LB0 21.7 AFT C061 30 30 GREY 27886 JOINER BULKHEADMESS NO. 17 3LB0 10.6 PORT C061 30 30 GREY 27886 JOINER BULKHEADMESS NO. 17 3LB0 11.3 STBD C212 36 36 INSULATION NOTE 4 C061 30 30 GREY 27886MESS NO. 17 3LB0 8.6 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480MESS NO. 19 3LZ0 33.9 ST DECK C413 125-150 DK COVERINGMESS NO. 19 3LZ0 35.7 DECKHEAD C212 36 36 NOTE 5 C061 30 30 WHITE 27925 PART INSULATIONMESS NO. 19 3LZ0 21.8 FORWARD C061 30 30 GREY 27875 JOINER BULKHEADMESS NO. 19 3LZ0 22.9 AFT C212 36 36 C061 30 30 GREY 27875MESS NO. 19 3LZ0 11.0 PORT C061 30 30 GREY 27875 JOINER BULKHEADMESS NO. 19 3LZ0 12.0 STBD C212 36 36 INSULATION NOTE 4 C061 30 30 GREY 27875MESS NO. 19 3LZ0 11.0 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480

STEERING GEAR COMPARTMENT 3MA0 6.2 ST DECK TRAFFIC C413 125-150 C200 750-1000 GREY 36076

STEERING GEAR COMPARTMENT 3MA0 18.9 ST DECK NON TRAFFIC 76 C413 AND

C045 C061 OR C177 30 30 GREY 16076

STEERING GEAR COMPARTMENT 3MA0 29.8 DECKHEAD C212 36 36 INSULATION C061 30 30 WHITE 27925STEERING GEAR COMPARTMENT 3MA0 17.5 FORWARD C212 36 36 INSULATION NOTE 5 WHITE 27925STEERING GEAR COMPARTMENT 3MA0 17.5 AFT C212 36 36 INSULATION NOTE 5 WHITE 27925STEERING GEAR COMPARTMENT 3MA0 15.9 PORT C212 36 36 INSULATION NOTE 5 WHITE 27925STEERING GEAR COMPARTMENT 3MA0 47.6 STBD C212 36 36 INSULATION NOTE 5 WHITE 27925STEERING GEAR COMPARTMENT 3MA0 28.0 OTHERS C061 30 30 GREY 16076 DADO (900mm HIGH)

ROPE STORE 3MA1 9.9 ST DECK TRAFFIC C413 125-150 C200 750-1000 GREY 36076

ROPE STORE 3MA1 13.7 ST DECK NON TRAFFIC

C413 AND C045 C061 OR C177 30 30 GREY 16076

ROPE STORE 3MA1 37.3 DECKHEAD C212 36 36 NOTE 4 C061 30 30 WHITE 27925 PART INSULATIONROPE STORE 3MA1 27.6 FORWARD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925ROPE STORE 3MA1 25.6 AFT C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925ROPE STORE 3MA1 33.4 PORT C212 36 36 C061 30 30 WHITE 27925ROPE STORE 3MA1 33.5 STBD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925ROPE STORE 3MA1 40.6 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480ROPE STORE 3MA1 29.9 OTHERS C061 30 30 GREY 16076 DADO (900mm HIGH)

LOBBY 3MA2 8.0 ST DECK TRAFFIC C413 125-150 C200 750-1000 GREY 36076

LOBBY 3MA2 3.8 ST DECK NON TRAFFIC

C413 AND C045 C061 OR C177 30 30 GREY 16076

LOBBY 3MA2 13.6 DECKHEAD C212 36 36 C061 30 30 WHITE 27925LOBBY 3MA2 20.9 FORWARD C212 36 36 C061 30 30 GREY 27880


Primer

DCZ Area M2

Surface1st Coat

µm


Name

Remarks

Rev: C


µm2nd Coat

µm


Finisher


µm3rd Coat

µm1st Coat

µm

LOBBY 3MA2 19.2 AFT C212 36 36 C061 30 30 GREY 27880LOBBY 3MA2 17.6 PORT C061 30 30 GREY 27880 JOINER BULKHEADLOBBY 3MA2 22.2 STBD C212 36 36 C061 30 30 GREY 27880LOBBY 3MA2 3.9 OTHERS C061 30 30 GREY 16076 DADO (150mm HIGH)DRY GARBAGE STORE(FFH330-FFH332), RESERVED SPACE(FFH333-FFH341) 3MA4 8.3 ST DECK

TRAFFIC C413 125-150 C200 750-1000 GREY 36076

DRY GARBAGE STORE(FFH330-FFH332), RESERVED SPACE(FFH333-FFH341) 3MA4 3.8 ST DECK NON

TRAFFICC413 AND

C045 C061 OR C177 30 30 GREY 16076

DRY GARBAGE STORE(FFH330-FFH332), RESERVED SPACE(FFH333-FFH341) 3MA4 17.0 DECKHEAD C212 36 36 NOTE 4 C061 30 30 WHITE 27925 PART INSULATION

DRY GARBAGE STORE(FFH330-FFH332), RESERVED SPACE(FFH333-FFH341) 3MA4 9.9 FORWARD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925

DRY GARBAGE STORE(FFH330-FFH332), RESERVED SPACE(FFH333-FFH341) 3MA4 8.5 AFT C212 36 36 C061 30 30 WHITE 27925

DRY GARBAGE STORE(FFH330-FFH332), RESERVED SPACE(FFH333-FFH341) 3MA4 16.0 PORT C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925

DRY GARBAGE STORE(FFH330-FFH332), RESERVED SPACE(FFH333-FFH341) 3MA4 14.7 STBD C061 30 30 WHITE 27925 JOINER BULKHEAD

DRY GARBAGE STORE(FFH330-FFH332), RESERVED SPACE(FFH333-FFH341) 3MA4 14.8 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480

DRY GARBAGE STORE(FFH330-FFH332), RESERVED SPACE(FFH333-FFH341) 3MA4 13.6 OTHERS C061 30 30 GREY 16076 DADO (900mm HIGH)

AFTER CLEANING GEAR STORE 3MZ0 2.1 ST DECK TRAFFIC C413 125-150 C200 750-1000 GREY 36076

AFTER CLEANING GEAR STORE 3MZ0 3.9 ST DECK NON TRAFFIC

C413 AND C045 C061 OR C177 30 30 GREY 16076

AFTER CLEANING GEAR STORE 3MZ0 10.7 DECKHEAD C212 36 36 NOTE 4 C061 30 30 WHITE 27925 PART INSULATIONAFTER CLEANING GEAR STORE 3MZ0 9.8 FORWARD C061 30 30 WHITE 27925 CLEAR OF JOINER BULKHEADAFTER CLEANING GEAR STORE 3MZ0 10.6 AFT C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925AFTER CLEANING GEAR STORE 3MZ0 10.9 PORT C212 36 36 C061 30 30 WHITE 27925AFTER CLEANING GEAR STORE 3MZ0 10.0 STBD C212 36 36 C061 30 30 WHITE 27925AFTER CLEANING GEAR STORE 3MZ0 9.7 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480AFTER CLEANING GEAR STORE 3MZ0 10.0 OTHERS C061 30 30 GREY 16076 DADO (900mm HIGH)

LOAN CLOTHING STORE 3MZ2 3.7 ST DECK TRAFFIC C413 125-150 C200 750-1000 GREY 36076

LOAN CLOTHING STORE 3MZ2 7.8 ST DECK NON TRAFFIC

C413 AND C045 C061 OR C177 30 30 GREY 16076

LOAN CLOTHING STORE 3MZ2 20.2 DECKHEAD C212 36 36 NOTE 4 C061 30 30 WHITE 27925 PART INSULATIONLOAN CLOTHING STORE 3MZ2 14.7 FORWARD C212 36 36 C061 30 30 WHITE 27925 CLEAR OF JOINER BULKHEADLOAN CLOTHING STORE 3MZ2 13.8 AFT C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925LOAN CLOTHING STORE 3MZ2 12.2 PORT C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925LOAN CLOTHING STORE 3MZ2 14.0 STBD C212 36 36 C061 30 30 WHITE 27925LOAN CLOTHING STORE 3MZ2 25.7 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480LOAN CLOTHING STORE 3MZ2 13.0 OTHERS C061 OR C177 30 30 GREY 16076 DADO (900mm HIGH)

PAINT STORE 2AA 15.1 ST DECK TRAFFIC C413 125-150 C200 750-1000 GREY 36076

PAINT STORE 2AA 1.5 ST DECK NON TRAFFIC

C413 AND C045 C061 OR C177 30 30 GREY 16076

PAINT STORE 2AA 30.0 DECKHEAD C212 36 36 NOTE 4 C061 30 30 WHITE 27925 PART INSULATIONPAINT STORE 2AA 2.0 FORWARD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925PAINT STORE 2AA 8.0 AFT C212 36 36 C061 30 30 WHITE 27925PAINT STORE 2AA 15.3 PORT C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925


Primer

DCZ Area M2

Surface1st Coat

µm


Name

Remarks

Rev: C


µm2nd Coat

µm


Finisher


µm3rd Coat

µm1st Coat

µm

PAINT STORE 2AA 15.3 STBD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925PAINT STORE 2AA 30.6 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480PAINT STORE 2AA 16.7 OTHERS C061 30 30 GREY 16076 DADO (900mm HIGH)

PAINT LOCKER 2AZ1 4.2 ST DECK TRAFFIC C413 125-150 C200 750-1000 GREY 36076

PAINT LOCKER 2AZ1 0.5 ST DECK NON TRAFFIC

C413 AND C045 C061 OR C177 30 30 GREY 16076

PAINT LOCKER 2AZ1 7.0 DECKHEAD C212 36 36 NOTE 4 C061 30 30 WHITE 27925 PART INSULATIONPAINT LOCKER 2AZ1 4.0 FORWARD C212 36 36 C061 30 30 WHITE 27925PAINT LOCKER 2AZ1 5.0 AFT C212 36 36 C061 30 30 WHITE 27925PAINT LOCKER 2AZ1 4.0 PORT C212 36 36 C061 30 30 WHITE 27925PAINT LOCKER 2AZ1 6.0 STBD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925PAINT LOCKER 2AZ1 6.0 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480PAINT LOCKER 2AZ1 7.8 OTHERS C061 30 30 GREY 16076 DADO (900mm HIGH)

FORWARD CLEANING GEAR STORE 2AZ2 4.2 ST DECK TRAFFIC C413 125-150 C200 750-1000 GREY 36076

FORWARD CLEANING GEAR STORE 2AZ2 0.5 ST DECK NON TRAFFIC

C413 AND C045 C061 OR C177 30 30 GREY 16076

FORWARD CLEANING GEAR STORE 2AZ2 7.0 DECKHEAD C212 36 36 NOTE 4 C061 30 30 WHITE 27925 PART INSULATIONFORWARD CLEANING GEAR STORE 2AZ2 7.8 FORWARD C212 36 36 C061 30 30 WHITE 27925FORWARD CLEANING GEAR STORE 2AZ2 8.4 AFT C212 36 36 C061 30 30 WHITE 27925FORWARD CLEANING GEAR STORE 2AZ2 9.2 PORT C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925FORWARD CLEANING GEAR STORE 2AZ2 7.8 STBD C212 36 36 C061 30 30 WHITE 27925FORWARD CLEANING GEAR STORE 2AZ2 9.2 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480FORWARD CLEANING GEAR STORE 2AZ2 7.8 OTHERS C061 30 30 GREY 16076 DADO (900mm HIGH)

ANCHOR CAPSTAN COMPARTMENT 2BA 26.4 ST DECK TRAFFIC C413 125-150 C200 750-1000 GREY 36076

ANCHOR CAPSTAN COMPARTMENT 2BA 2.9 ST DECK NON TRAFFIC

C413 AND C045 C061 OR C177 30 30 GREY 16076

ANCHOR CAPSTAN COMPARTMENT 2BA 53.9 DECKHEAD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925ANCHOR CAPSTAN COMPARTMENT 2BA 19.5 FORWARD C212 36 36 C061 30 30 WHITE 27925ANCHOR CAPSTAN COMPARTMENT 2BA 27.3 AFT C212 36 36 C061 30 30 WHITE 27925ANCHOR CAPSTAN COMPARTMENT 2BA 14.9 PORT C212 36 36 NOTE 4 C061 30 30 WHITE 27925 PART INSULATIONANCHOR CAPSTAN COMPARTMENT 2BA 28.0 STBD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925ANCHOR CAPSTAN COMPARTMENT 2BA 42.9 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480ANCHOR CAPSTAN COMPARTMENT 2BA 21.5 OTHERS C061 30 30 GREY 16076 DADO (900mm HIGH)PLATFORM (IN ANCHOR CAPSTAN COMPARTMENT) 2BA 9.6 ST DECK C413 125-150 C200 750-1000 GREY 36076

GENERAL STORE NO.1B 2BA 8.8 ST DECK TRAFFIC C413 125-150 C200 750-1000 GREY 36076

GENERAL STORE NO.1B 2BA 1.5 ST DECK NON TRAFFIC

C413 AND C045 C061 OR C177 30 30 GREY 16076

GENERAL STORE NO.1B 2BA 18.3 DECKHEAD C212 36 36 C061 30 30 WHITE 27925 DECKHEAD SUPPORT STRUCTURE ONLY

GENERAL STORE NO.1B 2BA 5.6 FORWARD C212 36 36 C061 30 30 WHITE 27925GENERAL STORE NO.1B 2BA 7.4 AFT C212 36 36 C061 30 30 WHITE 27925GENERAL STORE NO.1B 2BA 8.0 PORT C212 36 36 C061 30 30 WHITE 27925GENERAL STORE NO.1B 2BA 8.4 STBD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925GENERAL STORE NO.1B 2BA 8.4 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480GENERAL STORE NO.1B 2BA 10.5 OTHERS C061 30 30 GREY 16076 DADO (900MM HIGH)GENERAL STORE NO.1A 2BA 19.2 DECKHEAD C212 36 36 NOTE 4 C061 30 30 WHITE 27925 PART INSULATION


Primer

DCZ Area M2

Surface1st Coat

µm


Name

Remarks

Rev: C


µm2nd Coat

µm


Finisher


µm3rd Coat

µm1st Coat

µm

GENERAL STORE NO.1A 2BA 5.0 FORWARD C212 36 36 C061 30 30 WHITE 27925GENERAL STORE NO.1A 2BA 6.8 AFT C212 36 36 C061 30 30 WHITE 27925GENERAL STORE NO.1A 2BA 12.0 PORT C212 36 36 C061 30 30 WHITE 27925GENERAL STORE NO.1A 2BA 9.9 STBD C212 36 36 NOTE 4 C061 30 30 WHITE 27925 PART INSULATIONGENERAL STORE NO.1A 2BA 9.9 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480GENERAL STORE NO.1C (FFH330 TO FFH335) 2BA 13.0 DECKHEAD C212 36 36 NOTE 4 C061 30 30 WHITE 27925 PART INSULATIONGENERAL STORE NO.1C (FFH330 TO FFH335) 2BA 6.4 FORWARD C212 36 36 C061 30 30 WHITE 27925GENERAL STORE NO.1C (FFH330 TO FFH335) 2BA 5.6 AFT C212 36 36 C061 30 30 WHITE 27925GENERAL STORE NO.1C (FFH330 TO FFH335) 2BA 8.0 PORT C212 36 36 NOTE 4 C061 30 30 WHITE 27925 PART INSULATIONGENERAL STORE NO.1C (FFH330 TO FFH335) 2BA 6.0 STBD C212 36 36 C061 30 30 WHITE 27925GENERAL STORE NO.1C (FFH330 TO FFH335) 2BA 8.0 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480

LOBBY 2BZ0 3.5 ST DECK TRAFFIC C413 125-150 C200 750-1000 GREY 36076

LOBBY 2BZ0 0.4 ST DECK NON TRAFFIC

C413 AND C045 C061 OR C177 30 30 GREY 16076

LOBBY 2BZ0 3.9 DECKHEAD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925LOBBY 2BZ0 7.4 FORWARD C212 36 36 C061 30 30 GREY 27880LOBBY 2BZ0 7.4 AFT C212 36 36 C061 30 30 GREY 27880LOBBY 2BZ0 27.0 PORT C212 36 36 C061 30 30 GREY 27880LOBBY 2BZ0 2.7 STBD C212 36 36 C061 30 30 GREY 27880LOBBY 2BZ0 1.4 OTHERS C061 30 30 GREY 16076 DADO (150mm HIGH)UNDRESS 2BZ2 4.6 ST DECK C413 125-150 DK COVERINGUNDRESS 2BZ2 12.5 DECKHEAD C021 100 C021 100 WHITEUNDRESS 2BZ2 2.9 FORWARD C021 100 C021 100 WHITEUNDRESS 2BZ2 4.2 AFT C021 100 C021 100 WHITEUNDRESS 2BZ2 13.9 PORT C212 36 36 INSULATION C021 100 WHITEUNDRESS 2BZ2 6.3 STBD C021 100 C021 100 WHITEUNDRESS 2BZ2 13.9 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480DC SECTION BASE NO.1 2CA0 6.5 ST DECK C413 125-150 DK COVERINGDC SECTION BASE NO.1 2CA0 6.5 DECKHEAD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925DC SECTION BASE NO.1 2CA0 13.9 FORWARD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925DC SECTION BASE NO.1 2CA0 12.9 AFT C212 36 36 C061 30 30 WHITE 27925DC SECTION BASE NO.1 2CA0 7.8 PORT C061 30 30 WHITE 27925 JOINER BULKHEADDC SECTION BASE NO.1 2CA0 8.4 STBD C212 36 36 C061 30 30 WHITE 27925

WEAPONS WORKSHOP 2CA1 9.6 ST DECK TRAFFIC C413 125-150 C200 750-1000 GREY 36076

WEAPONS WORKSHOP 2CA1 1.7 ST DECK NON TRAFFIC

C413 AND C045 C061 OR C177 30 30 GREY 16076

WEAPONS WORKSHOP 2CA1 22.9 DECKHEAD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925WEAPONS WORKSHOP 2CA1 7.9 FORWARD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925WEAPONS WORKSHOP 2CA1 12.5 AFT C212 36 36 C061 30 30 WHITE 27925WEAPONS WORKSHOP 2CA1 21.4 PORT C212 36 36 C061 30 30 WHITE 27925WEAPONS WORKSHOP 2CA1 24.0 STBD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925WEAPONS WORKSHOP 2CA1 21.4 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480WEAPONS WORKSHOP 2CA1 13.0 OTHERS C061 30 30 GREY 16076 DADO (900mm HIGH)LOBBY 2CB0 10.5 ST DECK C413 125-150 DK COVERINGLOBBY 2CB0 16.1 DECKHEAD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925LOBBY 2CB0 11.5 FORWARD C212 36 36 C061 30 30 GREY 27880LOBBY 2CB0 11.5 AFT C061 30 30 GREY 27880 JOINER BULKHEADLOBBY 2CB0 24.5 PORT C212 36 36 C061 30 30 GREY 27880 CLEAR OF JOINER BULKHEADLOBBY 2CB0 24.5 STBD C061 30 30 GREY 27880 JOINER BULKHEAD


Primer

DCZ Area M2

Surface1st Coat

µm


Name

Remarks

Rev: C


µm2nd Coat

µm


Finisher


µm3rd Coat

µm1st Coat

µm

LOBBY 2CB0 2.1 OTHERS C061 30 30 GREY 16076 DADO (150mm HIGH)DAMAGE CONTROL LOBBY 2CB0 15.4 ST DECK C413 125-150 DK COVERINGDAMAGE CONTROL LOBBY 2CB0 23.1 DECKHEAD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925DAMAGE CONTROL LOBBY 2CB0 21.1 FORWARD C212 36 36 C061 30 30 WHITE 27925DAMAGE CONTROL LOBBY 2CB0 21.1 AFT C212 36 36 C061 30 30 WHITE 27925DAMAGE CONTROL LOBBY 2CB0 24.0 PORT C212 36 36 C061 30 30 WHITE 27925DAMAGE CONTROL LOBBY 2CB0 24.0 STBD C212 36 36 C061 30 30 WHITE 27925DAMAGE CONTROL LOBBY 2CB0 2.8 OTHERS C061 30 30 GREY 16076 DADO (150mm HIGH)FORWARD CLEANSING STATION (CLEANSE) 2CB2 9.5 ST DECK C413 125-150 DK COVERINGFORWARD CLEANSING STATION (CLEANSE) 2CB2 18.6 DECKHEAD C212 36 36 INSULATION C021 100 WHITEFORWARD CLEANSING STATION (CLEANSE) FFH330 2CB2 9.6 FORWARD C212 36 36 C418 50 50 WHITE

FORWARD CLEANSING STATION (CLEANSE) FFH331 TO FFH341 2CB2 9.6 FORWARD C021 100 C021 100 WHITE SHIPS FFH 331 TO FFH 341 ONLY

FORWARD CLEANSING STATION (CLEANSE) FFH330 2CB2 13.5 AFT C212 36 36 C418 50 50 WHITE

FORWARD CLEANSING STATION (CLEANSE) FFH331 TO FFH341 2CB2 13.5 AFT C021 100 C021 100 WHITE SHIPS FFH 331 TO FFH 341 ONLY

FORWARD CLEANSING STATION (CLEANSE) 2CB2 17.1 PORT C212 36 36 INSULATION C021 100 WHITEFORWARD CLEANSING STATION (CLEANSE) FFH330 2CB2 16.0 STBD C212 36 36 C418 50 50 WHITE

FORWARD CLEANSING STATION (CLEANSE) FFH331 TO FFH341 2CB2 16.0 STBD C021 100 C021 100 WHITE SHIPS FFH 331 TO FFH 341 ONLY

FORWARD CLEANSING STATION (CLEANSE) 2CB2 17.1 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480FORWARD CLEANSING STATION (STRIP) 2CA2 6.7 ST DECK C413 125-150 DK COVERINGFORWARD CLEANSING STATION (STRIP) 2CA2 16.8 DECKHEAD C212 36 36 INSULATION C021 100 WHITEFORWARD CLEANSING STATION (CLEANSE) FFH330 2CA2 6.7 FORWARD C212 36 36 C418 50 50 WHITE

FORWARD CLEANSING STATION (STRIP) FFH331 TO FFH341 2CA2 6.7 FORWARD C021 100 C021 100 WHITE SHIPS FFH 331 TO FFH 341 ONLY

FORWARD CLEANSING STATION (CLEANSE) FFH330 2CA2 6.7 AFT C212 36 36 C418 50 50 WHITE

FORWARD CLEANSING STATION (STRIP) FFH331 TO FFH341 2CA2 6.7 AFT C021 100 C021 100 WHITE SHIPS FFH 331 TO FFH 341 ONLY

FORWARD CLEANSING STATION (STRIP) 2CA2 19.2 PORT C212 36 36 INSULATION C021 100 WHITEFORWARD CLEANSING STATION (CLEANSE) FFH330 2CA2 19.2 STBD C212 36 36 C418 50 50 WHITE

FORWARD CLEANSING STATION (STRIP) FFH331 TO FFH341 2CA2 19.2 STBD C021 100 C021 100 WHITE SHIPS FFH 331 TO FFH 341 ONLY

FORWARD CLEANSING STATION (STRIP) 2CA2 1.8 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480MESS NO.1 2CY0 19.9 ST DECK C413 125-150 DK COVERINGMESS NO.1 2CY0 30.0 DECKHEAD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925MESS NO.1 2CY0 24.0 FORWARD C212 36 36 C061 30 30 GREY 27886MESS NO.1 2CY0 24.0 AFT C212 36 36 INSULATION NOTE 4 C061 30 30 GREY 27886 CLEAR OF JOINER BULKHEADMESS NO.1 2CY0 18.7 PORT C061 30 30 GREY 27886 JOINER BULKHEADMESS NO.1 2CY0 18.7 STBD C212 36 36 INSULATION NOTE 4 C061 30 30 GREY 27886MESS NO.1 2CY0 15.6 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480AIR LOCK 2CY2 1.6 ST DECK C413 125-150 DK COVERINGAIR LOCK 2CY2 1.6 DECKHEAD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925AIR LOCK 2CY2 5.3 FORWARD C212 36 36 C061 30 30 GREY 27880AIR LOCK 2CY2 5.3 AFT C212 36 36 C061 30 30 GREY 27880


Primer

DCZ Area M2

Surface1st Coat

µm


Name

Remarks

Rev: C


µm2nd Coat

µm


Finisher


µm3rd Coat

µm1st Coat

µm

AIR LOCK 2CY2 6.7 PORT C212 36 36 C061 30 30 GREY 27880AIR LOCK 2CY2 6.7 STBD C212 36 36 C061 30 30 GREY 27880AIR LOCK 2CY2 0.8 OTHERS C061 30 30 GREY 16076 DADO (150mm HIGH)CREWS WASHPLACE & HEAD NO.1 2CY4 13.2 ST DECK C413 125-150 DK COVERING GREY 27880CREWS WASHPLACE & HEAD NO.1 2CY4 24.8 DECKHEAD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925CREWS WASHPLACE & HEAD NO.1 2CY4 23.5 FORWARD C212 36 36 C061 30 30 GREY 27880CREWS WASHPLACE & HEAD NO.1 2CY4 23.5 AFT C212 36 36 C061 30 30 GREY 27880 CLEAR OF JOINER BULKHEAD

CREWS WASHPLACE & HEAD NO.1 2CY4 19.8 PORT C212 36 36 INSULATION NOTE 4 C061 30 30 GREY 27880

CLEAR OF FIBREGLASS LAYER. FOR FFH 330,331,332,334 & 335 APPLY 1 COAT 38 µm OF 1-GP-146M TO THE DOUBLE LAYER OF FIBREGLASS, COLOUR TO BE GREY 101-202. SEE NOTE 18 FOR FFH 333, 336 TO 341.

CREWS WASHPLACE & HEAD NO.1 2CY4 25.4 STBD C212 36 36 C061 30 30 GREY 27880 CLEAR OF JOINER BULKHEADCREWS WASHPLACE & HEAD NO.1 2CY4 19.8 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480CREWS WASHPLACE & HEAD NO.1 2CY4 6.0 OTHERS C212 36 36 C061 30 30 GREY 27880 SHOWER PARTITIONSCREWS WASHPLACE & HEAD NO.1 2CY4 6.0 OTHERS C061 30 30 GREY 27880 W.C. PARTITIONSMESS NO.2 2CZ 41.9 ST DECK C413 125-150 DK COVERINGMESS NO.2 2CZ 53.2 DECKHEAD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925MESS NO.2 2CZ 48.3 FORWARD C061 30 30 GREY 27875 JOINER BULKHEADMESS NO.2 2CZ 48.3 AFT C212 36 36 C061 30 30 GREY 27875MESS NO.2 2CZ 14.5 PORT C212 36 36 INSULATION NOTE 4 C061 30 30 GREY 27875MESS NO.2 2CZ 14.5 STBD C212 36 36 INSULATION NOTE 4 C061 30 30 GREY 27875MESS NO.2 2CZ 29.0 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480OPERATIONS ROOM 2DA 107.3 ST DECK C413 125-150 NOTE 15 BELOW FALSE DECKOPERATIONS ROOM 2DA 115.9 DECKHEAD C212 36 36 INSULATION NOTE 5 WHITE 27925OPERATIONS ROOM 2DA 25.9 FORWARD C212 36 36 INSULATION NOTE 5 GREEN 24664OPERATIONS ROOM 2DA 28.0 AFT C212 36 36 INSULATION NOTE 5 GREEN 24664OPERATIONS ROOM 2DA 17.3 PORT C212 36 36 INSULATION NOTE 5 GREEN 24664OPERATIONS ROOM 2DA 17.3 STBD C212 36 36 INSULATION NOTE 5 GREEN 24664OPERATIONS ROOM 2DA 61.1 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480

COMMAND & CONTROL EQUIPMENT ROOM NO.2 2DB0 22.0 ST DECK TRAFFIC C413 125-150 C200 750-1000 GREY 36076

COMMAND & CONTROL EQUIPMENT ROOM NO.2 2DB0 2.2 ST DECK NON TRAFFIC

C413 AND C045 C061 OR C177 30 30 GREY 16076

COMMAND & CONTROL EQUIPMENT ROOM NO.2 2DB0 23.8 DECKHEAD C212 36 36 INSULATION C061 30 30 WHITE 27925

COMMAND & CONTROL EQUIPMENT ROOM NO.2 2DB0 11.9 FORWARD C212 36 36 INSULATION NOTE 5 WHITE 27925

COMMAND & CONTROL EQUIPMENT ROOM NO.2 2DB0 11.9 AFT C212 36 36 INSULATION NOTE 5 WHITE 27925

COMMAND & CONTROL EQUIPMENT ROOM NO.2 2DB0 8.6 PORT C212 36 36 INSULATION NOTE 5 WHITE 27925

COMMAND & CONTROL EQUIPMENT ROOM NO.2 2DB0 8.6 STBD C212 36 36 INSULATION NOTE 5 WHITE 27925

SPS 49 COOLING EQUIPMENT ROOM 2DB1 40.5 ST DECK TRAFFIC C413 125-150 C200 750-1000 GREY 36076

SPS 49 COOLING EQUIPMENT ROOM 2DB1 4.1 ST DECK NON TRAFFIC

C413 AND C045 C061 OR C177 30 30 GREY 16076

SPS 49 COOLING EQUIPMENT ROOM 2DB1 9.3 DECKHEAD C212 36 36 INSULATION C061 30 30 WHITE 27925SPS 49 COOLING EQUIPMENT ROOM 2DB1 7.8 FORWARD C212 36 36 INSULATION NOTE 5 WHITE 27925


Primer

DCZ Area M2

Surface1st Coat

µm


Name

Remarks

Rev: C


µm2nd Coat

µm


Finisher


µm3rd Coat

µm1st Coat

µm

SPS 49 COOLING EQUIPMENT ROOM 2DB1 7.8 AFT C212 36 36 INSULATION NOTE 5 WHITE 27925SPS 49 COOLING EQUIPMENT ROOM 2DB1 4.0 PORT C212 36 36 INSULATION NOTE 5 WHITE 27925SPS 49 COOLING EQUIPMENT ROOM 2DB1 4.0 STBD C212 36 36 INSULATION NOTE 5 WHITE 27925SPS 49 COOLING EQUIPMENT ROOM 2DB1 7.0 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480

OPERATIONS ROOM A/C PLANT 2DB2 8.0 ST DECK TRAFFIC C413 125-150 C200 750-1000 GREY 36076

OPERATIONS ROOM A/C PLANT 2DB2 1.0 ST DECK NON TRAFFIC

C413 AND C045 C061 OR C177 30 30 GREY 16076

OPERATIONS ROOM A/C PLANT 2DB2 9.7 DECKHEAD C212 36 36 INSULATION C061 30 30 WHITE 27925OPERATIONS ROOM A/C PLANT 2DB2 5.4 FORWARD C212 36 36 INSULATION NOTE 5 WHITE 27925OPERATIONS ROOM A/C PLANT 2DB2 5.0 AFT C212 36 36 INSULATION NOTE 5 WHITE 27925OPERATIONS ROOM A/C PLANT 2DB2 7.6 PORT C212 36 36 INSULATION NOTE 5 WHITE 27925OPERATIONS ROOM A/C PLANT 2DB2 7.6 STBD C212 36 36 INSULATION NOTE 5 WHITE 27925OPERATIONS ROOM A/C PLANT 2DB2 7.6 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480

OPERATIONS ROOM A/C PLANT 2DB2 10.9 OTHERS C061 OR C177 30 30 GREY 501-102 DADO (900mm HIGH) EXCEPT OVER PERFORATED METAL.

FEMALE OFFICERS WASHPLACE & HEAD 2DY2 3.1 ST DECK C413 125-150 DK COVERINGFEMALE OFFICERS WASHPLACE & HEAD 2DY2 3.4 DECKHEAD C061 36 36 C061 30 30 WHITE 27925FEMALE OFFICERS WASHPLACE & HEAD 2DY2 3.8 FORWARD C061 30 30 GREY 27880 JOINER BULKHEADFEMALE OFFICERS WASHPLACE & HEAD 2DY2 3.8 AFT C061 30 30 GREY 27880 JOINER BULKHEADFEMALE OFFICERS WASHPLACE & HEAD 2DY2 4.0 PORT C061 30 30 GREY 27880 JOINER BULKHEADFEMALE OFFICERS WASHPLACE & HEAD 2DY2 4.0 STBD C061 30 30 GREY 27880 JOINER BULKHEADFEMALE OFFICERS WASHPLACE & HEAD 2DY2 2.4 OTHERS C061 36 36 C061 30 30 GREY 27880 SHOWER PARTITIONSOPERATIONS ROOM ADMINISTRATION AREA 2DY4 3.9 ST DECK C413 125-150 NOTE 15 BELOW FALSE DECKOPERATIONS ROOM ADMINISTRATION AREA 2DY4 4.3 DECK HEAD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925OPERATIONS ROOM ADMINISTRATION AREA 2DY4 5.2 FORWARD C212 36 36 C061 30 30 GREEN 24664OPERATIONS ROOM ADMINISTRATION AREA 2DY4 5.2 AFT C061 30 30 GREEN 24664 JOINER BULKHEADOPERATIONS ROOM ADMINISTRATION AREA 2DY4 3.2 PORT C212 36 36 INSULATION NOTE 4 C061 30 30 GREEN 24664OPERATIONS ROOM ADMINISTRATION AREA 2DY4 3.0 STBD C061 30 30 GREEN 24664 JOINER BULKHEADOPERATIONS ROOM ADMINISTRATION AREA 2DY4 4.3 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480

RADAR ROOM NO.2 2DZ0 40.5 ST DECK TRAFFIC C413 64 C200 750-1000 GREY 36076

RADAR ROOM NO.2 2DZ0 4.1 ST DECK NON TRAFFIC

C413 AND C045 C061 OR C177 30 30 GREY 16076

RADAR ROOM NO.2 2DZ0 43.7 DECKHEAD C212 36 36 INSULATION WHITE 27925RADAR ROOM NO.2 2DZ0 20.5 FORWARD C212 36 36 INSULATION NOTE 5 WHITE 27925RADAR ROOM NO.2 2DZ0 20.5 AFT C212 36 36 INSULATION NOTE 5 WHITE 27925RADAR ROOM NO.2 2DZ0 10.0 PORT C061 30 WHITE 27925 JOINER BULKHEADRADAR ROOM NO.2 2DZ0 10.8 STBD C212 36 36 INSULATION NOTE 5 WHITE 27925RADAR ROOM NO.2 2DZ0 15.0 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480PASSAGEWAY 2DZ2 26.3 ST DECK C413 125-150 DK COVERINGPASSAGEWAY 2DZ2 28.4 DECKHEAD C212 36 36 NOTE 4 C061 30 30 WHITE 27925 PART INSULATIONPASSAGEWAY 2DZ2 9.8 FORWARD C212 36 36 C061 30 30 GREY 27880PASSAGEWAY 2DZ2 9.8 AFT C212 36 36 C061 30 30 GREY 27880PASSAGEWAY 2DZ2 18.0 PORT C212 36 36 C061 30 30 GREY 27880 CLEAR OF JOINER BULKHEADPASSAGEWAY 2DZ2 18.0 STBD C212 36 36 C061 30 30 GREY 27880 CLEAR OF JOINER BULKHEADFEMALE OFFICERS CABIN 2DZ4 10.7 ST DECK C413 125-150 DK COVERINGFEMALE OFFICERS CABIN 2DZ4 11.5 DECKHEAD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925FEMALE OFFICERS CABIN 2DZ4 5.2 FORWARD C061 30 30 GREY 27886 JOINER BULKHEADFEMALE OFFICERS CABIN 2DZ4 5.6 AFT C212 36 36 C061 30 30 GREY 27886FEMALE OFFICERS CABIN 2DZ4 8.5 PORT C212 36 36 INSULATION NOTE 4 C061 30 30 GREY 27886FEMALE OFFICERS CABIN 2DZ4 8.0 STBD C061 30 30 GREY 27886 JOINER BULKHEADFEMALE OFFICERS CABIN 2DZ4 11.7 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480WARDROOM SERVERY 2EA0 11.8 ST DECK C413 125-150 DK COVERINGWARDROOM SERVERY 2EA0 12.7 DECKHEAD C212 36 36 C061 30 30 WHITE 27925WARDROOM SERVERY 2EA0 10.7 FORWARD C212 36 36 C061 30 30 WHITE 27925


Primer

DCZ Area M2

Surface1st Coat

µm


Name

Remarks

Rev: C


µm2nd Coat

µm


Finisher


µm3rd Coat

µm1st Coat

µm

WARDROOM SERVERY 2EA0 10.7 AFT C212 36 36 C061 30 30 WHITE 27925WARDROOM SERVERY 2EA0 11.9 PORT C212 36 36 C061 30 30 WHITE 27925WARDROOM SERVERY 2EA0 11.0 STBD C061 30 30 WHITE 27925 JOINER BULKHEADWARDROOM & ANTEROOM 2EA1 59.0 ST DECK C413 125-150 DK COVERINGWARDROOM & ANTEROOM 2EA1 69.4 DECKHEAD C212 36 36 NOTE 4 C061 30 30 WHITE 27925 PART INSULATIONWARDROOM & ANTEROOM 2EA1 23.0 FORWARD C212 36 36 C061 30 30 GREY 27886 LINING ON BULKHEADWARDROOM & ANTEROOM 2EA1 23.2 AFT C212 36 36 C061 30 30 GREY 27886 LINING ON BULKHEADWARDROOM & ANTEROOM 2EA1 29.7 PORT C212 36 36 C061 30 30 GREY 27886 LINING OVER STEEL BHDWARDROOM & ANTEROOM 2EA1 29.7 STBD C212 36 36 INSULATION C061 30 30 GREY 27886 LINING OVER INSULATIONWARDROOM & ANTEROOM 2EA1 29.7 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480PASSAGEWAY 2EA2 19.2 ST DECK C413 125-150 DK COVERINGPASSAGEWAY 2EA2 20.7 DECKHEAD C212 36 36 NOTE 4 C061 30 30 WHITE 27925 PART INSULATIONPASSAGEWAY 2EA2 11.4 FORWARD C212 36 36 C061 30 30 GREY 27880PASSAGEWAY 2EA2 11.4 AFT C212 36 36 C061 30 30 GREY 27880PASSAGEWAY 2EA2 29.7 PORT C212 36 36 C061 30 30 GREY 27880PASSAGEWAY 2EA2 29.7 STBD C212 36 36 C061 30 30 GREY 27880PASSAGEWAY 2EA2 4.2 OTHERS C061 30 30 GREY 16076 DADO (150mm HIGH)CONFIDENTIAL BOOKS OFFICE 2EA4 6.8 ST DECK C413 125-150 DK COVERINGCONFIDENTIAL BOOKS OFFICE 2EA4 9.0 DECKHEAD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925CONFIDENTIAL BOOKS OFFICE 2EA4 9.3 FORWARD C212 36 36 C061 30 30 GREEN 24585CONFIDENTIAL BOOKS OFFICE 2EA4 9.4 AFT C212 36 36 C061 30 30 GREEN 24585CONFIDENTIAL BOOKS OFFICE 2EA4 7.9 PORT C212 36 36 INSULATION NOTE 4 C061 30 30 GREEN 24585CONFIDENTIAL BOOKS OFFICE 2EA4 7.3 STBD C061 30 30 GREEN 24585 JOINER BULKHEADCONFIDENTIAL BOOKS OFFICE 2EA4 7.9 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480

WARDROOM LOCKER 2EB1 0.8 ST DECK TRAFFIC 76 C413 125-150 C200 750-1000 GREY 36076

WARDROOM LOCKER 2EB1 2.6 ST DECK NON TRAFFIC

C413 AND C045 C061 OR C177 30 30 GREY 16076

WARDROOM LOCKER 2EB1 3.7 DECKHEAD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925WARDROOM LOCKER 2EB1 6.6 FORWARD C212 36 36 C061 30 30 WHITE 27925WARDROOM LOCKER 2EB1 6.1 AFT C061 30 30 WHITE 27925 JOINER BULKHEADWARDROOM LOCKER 2EB1 4.3 PORT C061 30 30 WHITE 27925 JOINER BULKHEADWARDROOM LOCKER 2EB1 4.6 STBD C212 36 36 C061 30 30 WHITE 27925LOBBY 2EB1 8.8 ST DECK C413 125-150 DK COVERINGLOBBY 2EB1 10.6 DECKHEAD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925LOBBY 2EB1 13.1 FORWARD C212 36 36 C061 30 30 GREY 27880 CLEAR OF JOINER BULKHEADLOBBY 2EB1 13.1 AFT C212 36 36 C061 30 30 GREY 27880LOBBY 2EB1 9.0 PORT C212 36 36 C061 30 30 GREY 27880 CLEAR OF JOINER BULKHEADLOBBY 2EB1 9.0 STBD C212 36 36 C061 30 30 GREY 27880LOBBY 2EB1 2.2 OTHERS C061 30 30 GREY 16076 DADO (150mm HIGH)

FORWARD SWITCHBOARD ROOM 2EZ2 15.1 ST DECK TRAFFIC C413 125-150 C200 750-1000 GREY 36076

FORWARD SWITCHBOARD ROOM 2EZ2 13.0 ST DECK NON TRAFFIC

C413 AND C045 C061 OR C177 30 30 GREY 16076

FORWARD SWITCHBOARD ROOM 2EZ2 34.3 DECKHEAD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925FORWARD SWITCHBOARD ROOM 2EZ2 13.3 FORWARD C212 36 36 INSULATION NOTE 5 WHITE 27925FORWARD SWITCHBOARD ROOM 2EZ2 13.4 AFT C212 36 36 INSULATION NOTE 5 WHITE 27925FORWARD SWITCHBOARD ROOM 2EZ2 21.9 PORT C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925FORWARD SWITCHBOARD ROOM 2EZ2 21.9 STBD C212 36 36 C061 30 30 WHITE 27925FORWARD SWITCHBOARD ROOM 2EZ2 21.9 SHELL EXT 76 C045 50 C411 30 30 30 GREY 26480PASSAGEWAY(PORT) 2FA0 21.6 ST DECK C413 125-150 DK COVERINGPASSAGEWAY(PORT) 2FA0 24.1 DECKHEAD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925


Primer

DCZ Area M2

Surface1st Coat

µm


Name

Remarks

Rev: C


µm2nd Coat

µm


Finisher


µm3rd Coat

µm1st Coat

µm

PASSAGEWAY(PORT) 2FA0 4.3 FORWARD C212 36 36 C061 30 30 GREY 27880PASSAGEWAY(PORT) 2FA0 4.3 AFT C212 36 36 C061 30 30 GREY 27880PASSAGEWAY(PORT) 2FA0 60.2 PORT C061 30 30 GREY 27880 JOINER BULKHEADPASSAGEWAY(PORT) 2FA0 50.5 STBD C212 36 36 C061 30 30 GREY 27880PASSAGEWAY(PORT) 2FA0 6.3 OTHERS C061 30 30 GREY 16076 DADO (150mm HIGH)PASSAGEWAY(STBD) 2FA0 16.4 ST DECK C413 125-150 DK COVERINGPASSAGEWAY(STBD) 2FA0 18.3 DECKHEAD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925PASSAGEWAY(STBD) 2FA0 3.2 FORWARD C212 36 36 C061 30 30 GREY 27880PASSAGEWAY(STBD) 2FA0 3.0 AFT C061 30 30 GREY 27880 JOINER BULKHEADPASSAGEWAY(STBD) 2FA0 43.5 PORT C212 36 36 C061 30 30 GREY 27880PASSAGEWAY(STBD) 2FA0 44.2 STBD C061 30 30 GREY 27880 JOINER BULKHEADPASSAGEWAY(STBD) 2FA0 4.9 OTHERS C061 30 30 GREY 16076 DADO (150mm HIGH)PASSAGEWAY(CENTRE) 2FA0 9.1 ST DECK C413 125-150 DK COVERINGPASSAGEWAY(CENTRE) 2FA0 9.8 DECKHEAD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925PASSAGEWAY(CENTRE) 2FA0 19.7 FORWARD C212 36 36 C061 30 30 GREY 27880PASSAGEWAY(CENTRE) 2FA0 21.6 AFT C212 36 36 C061 30 30 GREY 27880PASSAGEWAY(CENTRE) 2FA0 4.3 PORT C212 36 36 C061 30 30 GREY 27880PASSAGEWAY(CENTRE) 2FA0 4.3 STBD C212 36 36 C061 30 30 GREY 27880PASSAGEWAY(CENTRE) 2FA0 2.5 OTHERS C061 30 30 GREY 16076 DADO (150mm HIGH)DOUBLE CABIN NO. 1 2FA1 10.6 ST DECK C413 125-150 DK COVERINGDOUBLE CABIN NO. 1 2FA1 12.9 DECKHEAD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925DOUBLE CABIN NO. 1 2FA1 11.2 FORWARD C212 36 36 C061 30 30 GREY 27886DOUBLE CABIN NO. 1 2FA1 10.4 AFT C061 30 30 GREY 27886 JOINER BULKHEADDOUBLE CABIN NO. 1 2FA1 8.7 PORT C061 30 30 GREY 27886 JOINER BULKHEADDOUBLE CABIN NO. 1 2FA1 9.4 STBD C212 36 36 INSULATION C061 30 30 GREY 27886DOUBLE CABIN NO. 1 2FA1 9.4 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480XO'S CABIN NO. 2 2FA2 8.2 ST DECK C413 125-150 DK COVERINGXO'S CABIN NO. 2 2FA2 10.0 DECKHEAD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925XO'S CABIN NO. 2 2FA2 11.1 FORWARD C212 36 36 C061 30 30 GREY 27886 LININGXO'S CABIN NO. 2 2FA2 10.4 AFT C061 30 30 GREY 27886 JOINER BULKHEADXO'S CABIN NO. 2 2FA2 7.8 PORT C212 36 36 INSULATION C061 30 30 GREY 27886XO'S CABIN NO. 2 2FA2 7.2 STBD C061 30 30 GREY 27886 JOINER BULKHEADXO'S CABIN NO. 2 2FA2 7.8 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480

HALON GAS COMPARTMENT 2FB0 3.7 ST DECK TRAFFIC C413 125-150 C200 750-1000 GREY 36076

HALON GAS COMPARTMENT 2FB0 4.9 ST DECK NON TRAFFIC

C413 AND C045 C411 30 30 GREY 16076

HALON GAS COMPARTMENT 2FB0 9.3 DECKHEAD C212 36 36 INSULATION C061 30 30 WHITE 27925HALON GAS COMPARTMENT 2FB0 19.7 FORWARD C212 36 36 C061 30 30 WHITE 27925HALON GAS COMPARTMENT 2FB0 19.7 AFT C212 36 36 C061 30 30 WHITE 27925HALON GAS COMPARTMENT 2FB0 3.9 PORT C212 36 36 INSULATION NOTE 5 WHITE 27925HALON GAS COMPARTMENT 2FB0 3.9 STBD C212 36 36 INSULATION NOTE 5 WHITE 27925HALON GAS COMPARTMENT 2FB0 14.2 OTHERS C061 30 30 GREY 16076 DADO (900mm HIGH)DOUBLE CABIN NO. 3 2FB1 9.9 ST DECK C413 125-150 DK COVERINGDOUBLE CABIN NO. 3 2FB1 10.9 DECKHEAD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925DOUBLE CABIN NO. 3 2FB1 9.9 FORWARD C061 30 30 GREY 27886 JOINER BULKHEADDOUBLE CABIN NO. 3 2FB1 10.4 AFT C061 30 30 GREY 27886 JOINER BULKHEADDOUBLE CABIN NO. 3 2FB1 8.5 PORT C061 30 30 GREY 27886 JOINER BULKHEADDOUBLE CABIN NO. 3 2FB1 8.7 STBD C212 36 36 INSULATION C061 30 30 GREY 27886DOUBLE CABIN NO. 3 2FB1 8.7 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480DOUBLE CABIN NO. 4 2FB2 10.1 ST DECK 76 C413 125-150 DK COVERINGDOUBLE CABIN NO. 4 2FB2 12.1 DECKHEAD C061 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925DOUBLE CABIN NO. 4 2FB2 10.4 FORWARD C061 30 30 GREY 27886 JOINER BULKHEAD


Primer

DCZ Area M2

Surface1st Coat

µm


Name

Remarks

Rev: C


µm2nd Coat

µm


Finisher


µm3rd Coat

µm1st Coat

µm

DOUBLE CABIN NO. 4 2FB2 10.4 AFT C061 30 30 GREY 27886 JOINER BULKHEADDOUBLE CABIN NO. 4 2FB2 9.1 PORT C061 36 36 INSULATION C061 30 30 GREY 27886DOUBLE CABIN NO. 4 2FB2 8.4 STBD C061 30 30 GREY 27886 JOINER BULKHEADDOUBLE CABIN NO. 4 2FB2 9.1 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480DOUBLE CABIN NO. 5 2FC1 9.9 ST DECK C413 125-150 DK COVERINGDOUBLE CABIN NO. 5 2FC1 10.9 DECKHEAD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925DOUBLE CABIN NO. 5 2FC1 9.7 FORWARD C061 30 30 GREY 27886 JOINER BULKHEADDOUBLE CABIN NO. 5 2FC1 10.4 AFT C061 30 30 GREY 27886 JOINER BULKHEADDOUBLE CABIN NO. 5 2FC1 8.8 PORT C061 30 30 GREY 27886 JOINER BULKHEADDOUBLE CABIN NO. 5 2FC1 8.7 STBD C212 36 36 INSULATION C061 30 30 GREY 27886DOUBLE CABIN NO. 5 2FC1 8.7 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480DOUBLE CABIN NO. 6 2FC2 21.2 ST DECK C413 125-150 DK COVERINGDOUBLE CABIN NO. 6 2FC2 25.1 DECKHEAD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925DOUBLE CABIN NO. 6 2FC2 10.4 FORWARD C061 30 30 GREY 27886 JOINER BULKHEADDOUBLE CABIN NO. 6 2FC2 10.4 AFT C061 30 30 GREY 27886 JOINER BULKHEADDOUBLE CABIN NO. 6 2FC2 18.8 PORT C212 36 36 INSULATION C061 30 30 GREY 27886DOUBLE CABIN NO. 6 2FC2 17.4 STBD C061 30 30 GREY 27886 JOINER BULKHEADDOUBLE CABIN NO. 6 2FC2 18.8 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480DOUBLE CABIN NO. 7 2FX1 9.4 ST DECK C413 125-150 DK COVERINGDOUBLE CABIN NO. 7 2FX1 10.3 DECKHEAD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925DOUBLE CABIN NO. 7 2FX1 9.7 FORWARD C061 30 30 GREY 27886 JOINER BULKHEADDOUBLE CABIN NO. 7 2FX1 10.4 AFT C061 30 30 GREY 27886 JOINER BULKHEADDOUBLE CABIN NO. 7 2FX1 8.4 PORT C061 30 30 GREY 27886 JOINER BULKHEADDOUBLE CABIN NO. 7 2FX1 8.3 STBD C212 36 36 INSULATION C061 30 30 GREY 27886DOUBLE CABIN NO. 7 2FX1 8.3 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480DOUBLE CABIN NO. 9 2FY1 10.8 ST DECK C413 125-150 DK COVERINGDOUBLE CABIN NO. 9 2FY1 11.7 DECKHEAD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925DOUBLE CABIN NO. 9 2FY1 10.4 FORWARD C061 30 30 GREY 27886 JOINER BULKHEADDOUBLE CABIN NO. 9 2FY1 10.4 AFT C061 30 30 GREY 27886 JOINER BULKHEADDOUBLE CABIN NO. 9 2FY1 7.8 PORT C061 30 30 GREY 27886 JOINER BULKHEADDOUBLE CABIN NO. 9 2FY1 8.4 STBD C212 36 36 INSULATION C061 30 30 GREY 27886DOUBLE CABIN NO. 9 2FY1 8.4 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480MEO'S CABIN NO. 10 2FY2 7.6 ST DECK C413 125-150 DK COVERINGMEO'S CABIN NO. 10 2FY2 9.1 DECKHEAD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925MEO'S CABIN NO. 10 2FY2 10.4 FORWARD C061 30 30 GREY 27886 JOINER BULKHEADMEO'S CABIN NO. 10 2FY2 10.4 AFT C061 30 30 GREY 27886 JOINER BULKHEADMEO'S CABIN NO. 10 2FY2 7.5 PORT C212 36 36 INSULATION C061 30 30 GREY 27886MEO'S CABIN NO. 10 2FY2 6.9 STBD C061 30 30 GREY 27886 JOINER BULKHEADMEO'S CABIN NO. 10 2FY2 7.5 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480OFFICERS WASHPLACE & HEADS 2FZ0 16.3 ST DECK C413 125-150 DK COVERINGOFFICERS WASHPLACE & HEADS 2FZ0 17.6 DECKHEAD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925OFFICERS WASHPLACE & HEADS 2FZ0 13.7 FORWARD C212 36 36 C061 30 30 GREY 27880OFFICERS WASHPLACE & HEADS 2FZ0 23.3 AFT C212 36 36 C061 30 30 GREY 27880OFFICERS WASHPLACE & HEADS 2FZ0 4.6 PORT C212 36 36 C061 30 30 GREY 27880OFFICERS WASHPLACE & HEADS 2FZ0 16.2 STBD C212 36 36 C061 30 30 GREY 27880OFFICERS WASHPLACE & HEADS 2FZ0 13.3 OTHERS C212 36 36 C061 30 30 GREY 27880 SHOWER PARTITIONSOFFICERS WASHPLACE & HEADS 2FZ0 24.8 OTHERS C061 30 30 GREY 27880 W.C. PARTITIONSSUPPLY OFFICERS CABIN NO. 14 2FZ1 9.3 ST DECK C413 125-150 DK COVERINGSUPPLY OFFICERS CABIN NO. 14 2FZ1 10.0 DECKHEAD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925SUPPLY OFFICERS CABIN NO. 14 2FZ1 6.4 FORWARD C212 36 36 C061 30 30 GREY 27886 JOINER BULKHEADSUPPLY OFFICERS CABIN NO. 14 2FZ1 5.2 AFT C212 36 36 C061 30 30 GREY 27886 LININGSUPPLY OFFICERS CABIN NO. 14 2FZ1 14.1 PORT C212 36 36 C061 30 30 GREY 27886 JOINER BULKHEADSUPPLY OFFICERS CABIN NO. 14 2FZ1 13.5 STBD C212 36 36 C061 30 30 GREY 27886 LININGAIR LOCK 2FZ2 5.4 DECKHEAD C212 36 36 NOTE 6 C061 30 30 WHITE 27925 PART INSULATION


Primer

DCZ Area M2

Surface1st Coat

µm


Name

Remarks

Rev: C


µm2nd Coat

µm


Finisher


µm3rd Coat

µm1st Coat

µm

AIR LOCK 2FZ2 4.9 FORWARD C212 36 36 INSULATION NOTE 5 GREY 27880AIR LOCK 2FZ2 4.9 AFT C212 36 36 INSULATION NOTE 5 GREY 27880AIR LOCK 2FZ2 9.0 PORT C212 36 36 INSULATION NOTE 5 GREY 27880AIR LOCK 2FZ2 9.0 STBD C212 36 36 INSULATION NOTE 5 GREY 27880AIR LOCK 2FZ2 1.4 OTHERS C061 30 30 GREY 16076 DADO (150mm HIGH)CSE/AIR OFFICERS CABIN NO. 11 2FZ3 10.8 ST DECK C413 125-150 DK COVERINGCSE/AIR OFFICERS CABIN NO. 11 2FZ3 12.4 DECKHEAD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925CSE/AIR OFFICERS CABIN NO. 11 2FZ3 13.5 FORWARD C061 30 30 GREY 27886 JOINER BULKHEADCSE/AIR OFFICERS CABIN NO. 11 2FZ3 14.6 AFT C212 36 36 C061 30 30 GREY 27886 LININGCSE/AIR OFFICERS CABIN NO. 11 2FZ3 6.9 PORT C212 36 36 C061 30 30 GREY 27886CSE/AIR OFFICERS CABIN NO. 11 2FZ3 6.9 STBD C212 36 36 INSULATION C061 30 30 GREY 27886CSE/AIR OFFICERS CABIN NO. 11 2FZ3 6.9 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480COMBAT OFFICERS CABIN NO. 12 2FZ4 7.7 ST DECK C413 125-150 DK COVERINGCOMBAT OFFICERS CABIN NO. 12 2FZ4 9.2 DECKHEAD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925COMBAT OFFICERS CABIN NO. 12 2FZ4 10.4 FORWARD C061 30 30 GREY 27886 JOINER BULKHEADCOMBAT OFFICERS CABIN NO. 12 2FZ4 11.2 AFT C212 36 36 C061 30 30 GREY 27886 LININGCOMBAT OFFICERS CABIN NO. 12 2FZ4 7.3 PORT C212 36 36 INSULATION C061 30 30 GREY 27886COMBAT OFFICERS CABIN NO. 12 2FZ4 6.8 STBD C061 30 30 GREY 27886 JOINER BULKHEADCOMBAT OFFICERS CABIN NO. 12 2FZ4 7.3 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480MESS NO. 3 2GA1 21.3 ST DECK C413 64 DK COVERINGMESS NO. 3 2GA1 24.5 DECKHEAD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925MESS NO. 3 2GA1 14.6 FORWARD C212 36 36 C061 30 30 GREY 27875MESS NO. 3 2GA1 13.3 AFT C061 30 30 GREY 27875 JOINER BULKHEADMESS NO. 3 2GA1 13.8 PORT C212 36 36 C061 30 30 GREY 27875MESS NO. 3 2GA1 13.7 STBD C212 36 36 INSULATION NOTE 4 C061 30 30 GREY 27875MESS NO. 3 2GA1 13.7 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480AIR LOCK 2GA2 2.6 ST DECK C413 125-150 DK COVERINGAIR LOCK 2GA2 2.8 DECKHEAD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925AIR LOCK 2GA2 3.8 FORWARD C212 36 36 C061 30 30 GREY 27880AIR LOCK 2GA2 3.8 AFT C212 36 36 C061 30 30 GREY 27880AIR LOCK 2GA2 5.9 PORT C212 36 36 C061 30 30 GREY 27880AIR LOCK 2GA2 5.9 STBD C212 36 36 C061 30 30 GREY 27880AIR LOCK 2GA2 1.0 OTHERS C061 30 30 GREY 16076 DADO (150mm HIGH)OPERATING & TREATMENT ROOM 2GA4 9.9 ST DECK C413 125-150 DK COVERINGOPERATING & TREATMENT ROOM 2GA4 11.6 DECKHEAD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925OPERATING & TREATMENT ROOM 2GA4 10.3 FORWARD C061 30 30 GREY 27880 JOINER BULKHEADOPERATING & TREATMENT ROOM 2GA4 11.3 AFT C212 36 36 C061 30 30 GREY 27880

OPERATING & TREATMENT ROOM 2GA4 8.3 PORT C212 36 36 INSULATION C021 100 GREY 27880


OPERATING & TREATMENT ROOM 2GA4 7.7 STBD C061 30 30 GREY 27880 JOINER BULKHEADOPERATING & TREATMENT ROOM 2GA4 8.3 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480ADMINISTRATION & RECEPTION AREA 2GA4 13.2 ST DECK C413 125-150 DK COVERINGADMINISTRATION & RECEPTION AREA 2GA4 15.9 DECKHEAD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925ADMINISTRATION & RECEPTION AREA 2GA4 9.9 FORWARD C061 30 30 GREY 27880 JOINER BULKHEADADMINISTRATION & RECEPTION AREA 2GA4 10.3 AFT C061 30 30 GREY 27880 JOINER BULKHEAD


Primer

DCZ Area M2

Surface1st Coat

µm


Name

Remarks

Rev: C


µm2nd Coat

µm


Finisher


µm3rd Coat

µm1st Coat

µm

ADMINISTRATION & RECEPTION AREA 2GA4 14.8 PORT C212 36 36 INSULATION C021 100 GREY 27880


ADMINISTRATION & RECEPTION AREA 2GA4 22.9 STBD C061 30 30 GREY 27880 JOINER BULKHEADADMINISTRATION & RECEPTION AREA 2GA4 14.8 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480RECUPERATION AREA 2GA4 7.3 ST DECK C413 125-150 DK COVERINGRECUPERATION AREA 2GA4 8.5 DECKHEAD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925RECUPERATION AREA 2GA4 10.7 FORWARD C212 36 36 C061 30 30 GREY 27880RECUPERATION AREA 2GA4 9.9 AFT C061 30 30 GREY 27880 JOINER BULKHEAD

RECUPERATION AREA 2GA4 6.6 PORT C212 36 36 INSULATION C021 100 GREY 27880


RECUPERATION AREA 2GA4 6.1 STBD C212 36 36 C061 30 30 GREY 27880RECUPERATION AREA 2GA4 6.6 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480

EIC COMPARTMENT 2GB1 4.5 ST DECK TRAFFIC C413 125-150 C200 750-1000 GREY 36076

EIC COMPARTMENT 2GB1 3.4 ST DECK NON TRAFFIC

C413 AND C045 C061 OR C177 30 30 GREY 16076

EIC COMPARTMENT 2GB1 8.5 DECKHEAD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925EIC COMPARTMENT 2GB1 9.8 FORWARD C212 36 36 C061 30 30 WHITE 27925EIC COMPARTMENT 2GB1 10.6 AFT C212 36 36 C061 30 30 WHITE 27925EIC COMPARTMENT 2GB1 6.8 PORT C212 36 36 C061 30 30 WHITE 27925EIC COMPARTMENT 2GB1 6.8 STBD C212 36 36 C061 30 30 WHITE 27925BATHROOM 2GB2 3.4 ST DECK C413 125-150 DK COVERINGBATHROOM 2GB2 3.7 DECKHEAD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925BATHROOM 2GB2 4.6 FORWARD C061 30 30 GREY 27880 JOINER BULKHEADBATHROOM 2GB2 4.6 AFT C061 30 30 GREY 27880 JOINER BULKHEADBATHROOM 2GB2 5.6 PORT C061 30 30 GREY 27880 JOINER BULKHEADBATHROOM 2GB2 5.6 STBD C061 30 30 GREY 27880 JOINER BULKHEAD

AFFF EQUIPMENT ROOM 2GZ1 7.1 ST DECK TRAFFIC C413 125-150 C200 750-1000 GREY 36076

AFFF EQUIPMENT ROOM 2GZ1 5.4 ST DECK NON TRAFFIC

C413 AND C045 C061 OR C177 30 30 GREY 16076

AFFF EQUIPMENT ROOM 2GZ1 13.5 DECKHEAD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925AFFF EQUIPMENT ROOM 2GZ1 10.6 FORWARD C212 36 36 C061 30 30 WHITE 27925AFFF EQUIPMENT ROOM 2GZ1 10.3 AFT C212 36 36 C061 30 30 WHITE 27925AFFF EQUIPMENT ROOM 2GZ1 12.6 PORT C212 36 36 C061 30 30 WHITE 27925AFFF EQUIPMENT ROOM 2GZ1 11.1 STBD C212 36 36 C061 30 30 WHITE 27925AFFF EQUIPMENT ROOM 2GZ1 13.5 OTHERS C061 30 30 GREY 16076 DADO (900mm HIGH)PASSAGEWAY 2GZ2 13.6 ST DECK C413 125-150 DK COVERINGPASSAGEWAY 2GZ2 15.4 DECKHEAD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925PASSAGEWAY 2GZ2 3.8 FORWARD C212 36 36 C061 30 30 GREY 27880PASSAGEWAY 2GZ2 4.8 AFT C212 36 36 C061 30 30 GREY 27880PASSAGEWAY 2GZ2 22.1 PORT C061 30 30 GREY 27880 JOINER BULKHEADPASSAGEWAY 2GZ2 32.0 STBD C212 36 36 C061 30 30 GREY 27880PASSAGEWAY 2GZ2 3.3 OTHERS C061 30 30 GREY 16076 DADO (150mm HIGH)


Primer

DCZ Area M2

Surface1st Coat

µm


Name

Remarks

Rev: C


µm2nd Coat

µm


Finisher


µm3rd Coat

µm1st Coat

µm

ENGINE ROOM TRUNKED ESCAPE 2GZ2 2.2 ST DECK C413 125-150 C200 750-1000 GREY 36076ENGINE ROOM TRUNKED ESCAPE 2GZ2 2.4 DECKHEAD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925ENGINE ROOM TRUNKED ESCAPE 2GZ2 3.9 FORWARD C212 36 36 INSULATION NOTE 5 WHITE 27925ENGINE ROOM TRUNKED ESCAPE 2GZ2 3.9 AFT C212 36 36 INSULATION NOTE 5 WHITE 27925ENGINE ROOM TRUNKED ESCAPE 2GZ2 4.9 PORT C212 36 36 INSULATION NOTE 5 WHITE 27925ENGINE ROOM TRUNKED ESCAPE 2GZ2 4.9 STBD C212 36 36 INSULATION NOTE 5 WHITE 27925LOBBY 2GZ3 6.7 ST DECK C413 125-150 DK COVERINGLOBBY 2GZ3 7.7 DECKHEAD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925LOBBY 2GZ3 3.7 FORWARD C061 30 30 GREY 27880 JOINER BULKHEADLOBBY 2GZ3 4.0 AFT C212 36 36 C061 30 30 GREY 27880LOBBY 2GZ3 16.1 PORT C212 36 36 C061 30 30 GREY 27880LOBBY 2GZ3 15.9 STBD C061 30 30 GREY 27880 JOINER BULKHEADLOBBY 2GZ3 2.1 OTHERS C061 30 30 GREY 16076 DADO (150mm HIGH)MESS NO. 4 2GZ5 15.4 ST DECK C413 125-150 DK COVERINGMESS NO. 4 2GZ5 18.5 DECKHEAD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925MESS NO. 4 2GZ5 9.6 FORWARD C061 30 30 GREY 27875 JOINER BULKHEADMESS NO. 4 2GZ5 8.4 AFT C212 36 36 C061 30 30 GREY 27875MESS NO. 4 2GZ5 15.9 PORT C061 30 30 GREY 27875 JOINER BULKHEADMESS NO. 4 2GZ5 16.0 STBD C212 36 36 INSULATION NOTE 4 C061 30 30 GREY 27875MESS NO. 4 2GZ5 16.0 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480

FCER NO. 2 2HA1 12.9 ST DECK TRAFFIC C413 125-150 C200 750-1000 GREY 36076

FCER NO. 2 2HA1 13.1 ST DECK NON TRAFFIC

C413 AND C045 C061 OR C177 30 30 GREY 16076

FCER NO. 2 2HA1 28.1 DECKHEAD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925FCER NO. 2 2HA1 10.3 FORWARD C212 36 36 C061 30 30 WHITE 27925FCER NO. 2 2HA1 12.2 AFT C212 36 36 C061 30 30 WHITE 27925FCER NO. 2 2HA1 22.1 PORT C212 36 36 C061 30 30 WHITE 27925FCER NO. 2 2HA1 20.8 STBD C212 36 36 C061 30 30 WHITE 27925MAINTENANCE CO-ORD/MSE OFFICE 2HA2 19.2 ST DECK C413 125-150 DK COVERINGMAINTENANCE CO-ORD/MSE OFFICE 2HA2 22.5 DECKHEAD C212 36 36 NOTE 4 C061 30 30 WHITE 27925 PART INSULATIONMAINTENANCE CO-ORD/MSE OFFICE 2HA2 12.4 FORWARD C212 36 36 C061 30 30 GREEN 24585MAINTENANCE CO-ORD/MSE OFFICE 2HA2 11.4 AFT C061 30 30 GREEN 24585 JOINER BULKHEADMAINTENANCE CO-ORD/MSE OFFICE 2HA2 14.8 PORT C212 36 36 INSULATION NOTE 4 C061 30 30 GREEN 24585MAINTENANCE CO-ORD/MSE OFFICE 2HA2 14.8 STBD C212 36 36 C061 30 30 GREEN 24585MAINTENANCE CO-ORD/MSE OFFICE 2HA2 14.8 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480C & PO'S WASHPLACE & HEADS (FEMALE) 2HA3 8.4 ST DECK C413 125-150 DK COVERING GREY 27880C & PO'S WASHPLACE & HEADS (FEMALE) 2HA3 10.2 DECKHEAD C212 36 36 NOTE 4 C061 30 30 WHITE 27925 PART INSULATIONC & PO'S WASHPLACE & HEADS (FEMALE) 2HA3 7.7 FORWARD C061 30 30 GREY 27880 JOINER BULKHEADC & PO'S WASHPLACE & HEADS (FEMALE) 2HA3 9.1 AFT C212 36 36 C061 30 30 GREY 27880C & PO'S WASHPLACE & HEADS (FEMALE) 2HA3 10.6 PORT C212 36 36 C061 30 30 GREY 27880 CLEAR OF JOINER BULKHEAD

C & PO'S WASHPLACE & HEADS (FEMALE) 2HA3 9.6 STBD C212 36 36 INSULATION NOTE 4 C061 30 30 GREY 27880

CLEAR OF FIBREGLASS LAYER. FOR FFH 330,331,332,334 & 335 APPLY 1 COAT 38 µm OF C021 TO THE DOUBLE LAYER OF FIBREGLASS, COLOUR TO BE GREY 27880. SEE NOTE 18 FOR FFH 333, 336 TO 341.

C & PO'S WASHPLACE & HEADS (FEMALE) 2HA3 9.6 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480C & PO'S WASHPLACE & HEADS (FEMALE) 2HA3 4.5 OTHERS C212 36 36 C061 30 30 GREY 16076 SHOWER PARTITIONSC & PO'S WASHPLACE & HEADS (FEMALE) 2HA3 19.0 OTHERS C061 30 30 GREY 16076 W.C. PARTITIONS

PASSAGEWAY(CASUALTY CLEARING STATION) 2HZ0 33.7 ST DECK C413 125-150 DK COVERING


Primer

DCZ Area M2

Surface1st Coat

µm


Name

Remarks

Rev: C


µm2nd Coat

µm


Finisher


µm3rd Coat

µm1st Coat

µm

PASSAGEWAY(CASUALTY CLEARING STATION) 2HZ0 25.6 DECKHEAD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925

PASSAGEWAY(CASUALTY CLEARING STATION) 2HZ0 20.8 FORWARD C212 36 36 C061 30 30 GREY 27880

PASSAGEWAY(CASUALTY CLEARING STATION) 2HZ0 11.9 AFT C212 36 36 C061 30 30 GREY 27880

PASSAGEWAY(CASUALTY CLEARING STATION) 2HZ0 23.8 PORT C212 36 36 C061 30 30 GREY 27880

PASSAGEWAY(CASUALTY CLEARING STATION) 2HZ0 14.9 STBD C212 36 36 C061 30 30 GREY 27880

PASSAGEWAY(CASUALTY CLEARING STATION) 2HZ0 3.6 OTHERS C061 30 30 GREY 16076 DADO (150mm HIGH)PASSAGEWAY(STBD) 2HZ0 10.0 ST DECK C413 125-150 DK COVERINGPASSAGEWAY(STBD) 2HZ0 10.8 DECKHEAD C212 36 36 C061 30 30 WHITE 27925PASSAGEWAY(STBD) 2HZ0 4.2 FORWARD C212 36 36 C061 30 30 GREY 27880PASSAGEWAY(STBD) 2HZ0 4.2 AFT C212 36 36 C061 30 30 GREY 27880PASSAGEWAY(STBD) 2HZ0 23.8 PORT C212 36 36 C061 30 30 GREY 27880PASSAGEWAY(STBD) 2HZ0 25.7 STBD C212 36 36 C061 30 30 GREY 27880 CLEAR OF JOINER BULKHEADPASSAGEWAY(STBD) 2HZ0 2.9 OTHERS C061 30 30 GREY 16076 DADO (150mm HIGH)PASSAGEWAY(CENTRELINE) 2HZ0 4.4 ST DECK C413 125-150 DK COVERINGPASSAGEWAY(CENTRELINE) 2HZ0 4.8 DECKHEAD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925PASSAGEWAY(CENTRELINE) 2HZ0 12.2 FORWARD C212 36 36 C061 30 30 GREY 27880PASSAGEWAY(CENTRELINE) 2HZ0 11.9 AFT C212 36 36 C061 30 30 GREY 27880PASSAGEWAY(CENTRELINE) 2HZ0 3.2 PORT C212 36 36 C061 30 30 GREY 27880PASSAGEWAY(CENTRELINE) 2HZ0 2.9 STBD C212 36 36 C061 30 30 GREY 27880PASSAGEWAY(CENTRELINE) 2HZ0 1.4 OTHERS C061 30 30 GREY 16076 DADO (150mm HIGH)CPO'S & P1'S WASHPLACE & HEADS (MALE) 2HZ1 12.2 ST DECK 76 C143 125-150 DK COVERING GREY 27880CPO'S & P1'S WASHPLACE & HEADS (MALE) 2HZ1 14.8 DECKHEAD C212 36 36 NOTE 4 C061 30 30 WHITE 27925 PART INSULATIONCPO'S & P1'S WASHPLACE & HEADS (MALE) 2HZ1 9.1 FORWARD C212 36 36 C061 30 30 GREY 27880CPO'S & P1'S WASHPLACE & HEADS (MALE) 2HZ1 7.9 AFT C212 36 36 C061 30 30 GREY 27880CPO'S & P1'S WASHPLACE & HEADS (MALE) 2HZ1 18.8 PORT C212 36 36 C061 30 30 GREY 27880 CLEAR OF JOINER BULKHEAD

CPO'S & P1'S WASHPLACE & HEADS (MALE) 2HZ1 14.1 STBD C212 36 36 INSULATION NOTE 4 C061 30 30 GREY 27880

CLEAR OF FIBREGLASS LAYER. FOR FFH 330,331,332,334 & 335 APPLY 1 COAT 38 µm OF C021 TO THE DOUBLE LAYER OF FIBREGLASS, COLOUR TO BE GREY 27880. SEE NOTE 18 FOR FFH 333, 336 TO 341.

CPO'S & P1'S WASHPLACE & HEADS (MALE) 2HZ1 14.1 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480CPO'S & P1'S WASHPLACE & HEADS (MALE) 2HZ1 6.0 OTHERS C212 36 36 C061 30 30 GREY 16076 SHOWER PARTITIONSCPO'S & P1'S WASHPLACE & HEADS (MALE) 2HZ1 18.5 OTHERS C061 30 30 GREY 16076 W.C. PARTITIONSCSE OFFICE 2HZ2 11.4 ST DECK C413 125-150 DK COVERINGCSE OFFICE 2HZ2 13.4 DECKHEAD C212 36 36 NOTE 4 C061 30 30 WHITE 27925 PART INSULATIONCSE OFFICE 2HZ2 11.4 FORWARD C061 30 30 GREEN 24585 JOINER BULKHEADCSE OFFICE 2HZ2 12.2 AFT C212 36 36 C061 30 30 GREEN 24585CSE OFFICE 2HZ2 9.0 PORT C212 36 36 INSULATION NOTE 4 C061 30 30 GREEN 24585CSE OFFICE 2HZ2 9.0 STBD C212 36 36 C061 30 30 GREEN 24585CSE OFFICE 2HZ2 9.0 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480

AVIONICS WORKSHOP 2JA0 8.3 ST DECK TRAFFIC C413 125-150 C200 750-1000 GREY 36076

AVIONICS WORKSHOP 2JA0 5.5 ST DECK NON TRAFFIC

C413 AND C045 C061 OR C177 30 30 GREY 16076

AVIONICS WORKSHOP 2JA0 15.0 DECKHEAD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925AVIONICS WORKSHOP 2JA0 13.2 FORWARD C212 36 36 C061 30 30 WHITE 27925AVIONICS WORKSHOP 2JA0 13.4 AFT C061 30 30 WHITE 27925 JOINER BULKHEAD


Primer

DCZ Area M2

Surface1st Coat

µm


Name

Remarks

Rev: C


µm2nd Coat

µm


Finisher


µm3rd Coat

µm1st Coat

µm

AVIONICS WORKSHOP 2JA0 13.4 PORT C061 30 30 WHITE 27925 JOINER BULKHEADAVIONICS WORKSHOP 2JA0 8.8 STBD C061 30 30 WHITE 27925 JOINER BULKHEADAVIONICS WORKSHOP 2JA0 15.7 OTHERS C061 30 30 GREY 16076 DADO (900 mm HIGH)LOBBY 2JA1 7.9 ST DECK C413 125-150 DK COVERINGLOBBY 2JA1 8.5 DECKHEAD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925LOBBY 2JA1 4.6 FORWARD C212 36 36 C061 30 30 GREY 27880LOBBY 2JA1 3.0 AFT C061 30 30 GREY 27880 JOINER BULKHEADLOBBY 2JA1 17.3 PORT C061 30 30 GREY 27880 JOINER BULKHEADLOBBY 2JA1 15.8 STBD C212 36 36 C061 30 30 GREY 27880LOBBY 2JA1 2.2 OTHERS C061 30 30 GREY 16076 DADO (150 mm HIGH)PASSAGEWAY/LOBBY 2JA2 22.1 ST DECK C413 125-150 DK COVERINGPASSAGEWAY/LOBBY 2JA2 22.1 DECKHEAD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925PASSAGEWAY/LOBBY 2JA2 12.3 FORWARD C212 36 36 C061 30 30 GREY 27880PASSAGEWAY/LOBBY 2JA2 12.3 AFT C212 36 36 C061 30 30 GREY 27880PASSAGEWAY/LOBBY 2JA2 31.9 PORT C212 36 36 C061 30 30 GREY 27880PASSAGEWAY/LOBBY 2JA2 39.9 STBD C061 30 30 GREY 27880 JOINER BULKHEADPASSAGEWAY/LOBBY 2JA2 5.1 OTHERS C061 30 30 GREY 16076 DADO (150 mm HIGH)MESS NO. 5 2JA3 15.4 ST DECK C413 125-150 DK COVERINGMESS NO. 5 2JA3 18.2 DECKHEAD C212 36 36 NOTE 4 C061 30 30 WHITE 27925 PART INSULATIONMESS NO. 5 2JA3 11.5 FORWARD C212 36 36 C061 30 30 GREY 27875MESS NO. 5 2JA3 10.7 AFT C061 30 30 GREY 27875 JOINER BULKHEADMESS NO. 5 2JA3 11.8 PORT C212 36 36 C061 30 30 GREY 27875MESS NO. 5 2JA3 12.5 STBD C212 36 36 INSULATION NOTE 4 C061 30 30 GREY 27875MESS NO. 5 2JA3 11.6 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480AIR DETACHMENT ROOM 2JA4 16.6 ST DECK C413 125-150 DK COVERINGAIR DETACHMENT ROOM 2JA4 18.1 DECKHEAD C212 36 36 NOTE 4 C061 30 30 WHITE 27925 PART INSULATIONAIR DETACHMENT ROOM 2JA4 11.3 FORWARD C212 36 36 C061 30 30 GREEN 24585AIR DETACHMENT ROOM 2JA4 10.5 AFT C061 30 30 GREEN 24585 JOINER BULKHEADAIR DETACHMENT ROOM 2JA4 13.2 PORT C212 36 36 INSULATION NOTE 4 C061 30 30 GREEN 24585AIR DETACHMENT ROOM 2JA4 13.2 STBD C212 36 36 C061 30 30 GREEN 24585AIR DETACHMENT ROOM 2JA4 12.3 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480

AVIATION STORE 2JB0 4.1 ST DECK TRAFFIC C413 125-150 C200 750-1000 GREY 36076

AVIATION STORE 2JB0 9.8 ST DECK NON TRAFFIC

C413 AND C045 C061 OR C177 30 30 GREY 16076

AVIATION STORE 2JB0 15.0 DECKHEAD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925AVIATION STORE 2JB0 13.4 FORWARD C061 30 30 WHITE 27925 JOINER BULKHEADAVIATION STORE 2JB0 14.3 AFT C212 36 36 C061 30 30 WHITE 27925 CLEAR OF JOINER BULKHEADAVIATION STORE 2JB0 7.5 PORT C061 30 30 WHITE 27925 JOINER BULKHEADAVIATION STORE 2JB0 8.2 STBD C061 30 30 WHITE 27925 JOINER BULKHEADAVIATION STORE 2JB0 14.3 OTHERS C061 30 30 GREY 16076 DADO (900 mm HIGH)AIR DETACHMENT ROOM HEADS 2JB2 2.7 ST DECK C413 125-150 DK COVERING GREY 27880AIR DETACHMENT ROOM HEADS 2JB2 3.6 DECKHEAD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925AIR DETACHMENT ROOM HEADS 2JB2 3.3 FORWARD C061 30 30 GREY 27880 JOINER BULKHEADAIR DETACHMENT ROOM HEADS 2JB2 3.3 AFT C061 30 30 GREY 27880 JOINER BULKHEAD

AIR DETACHMENT ROOM HEADS 2JB2 7.7 PORT C212 36 36 INSULATION NOTE 4 C061 30 30 GREY 27880


AIR DETACHMENT ROOM HEADS 2JB2 7.2 STBD C061 30 30 GREY 27880 JOINER BULKHEADAIR DETACHMENT ROOM HEADS 2JB2 7.2 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480


Primer

DCZ Area M2

Surface1st Coat

µm


Name

Remarks

Rev: C


µm2nd Coat

µm


Finisher


µm3rd Coat

µm1st Coat

µm

AIR MECHANICS & AIR ARMAMENT WORKSHOP 2JZ0 7.8 ST DECK TRAFFIC C413 125-150 C200 750-1000 GREY 36076

AIR MECHANICS & AIR ARMAMENT WORKSHOP 2JZ0 5.3 ST DECK NON TRAFFIC

C413 AND C045 C061 30 30 GREY 16076

AIR MECHANICS & AIR ARMAMENT WORKSHOP 2JZ0 14.1 DECKHEAD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925

AIR MECHANICS & AIR ARMAMENT WORKSHOP 2JZ0 10.6 FORWARD C061 30 30 WHITE 27925 JOINER BULKHEAD

AIR MECHANICS & AIR ARMAMENT WORKSHOP 2JZ0 11.4 AFT C212 36 36 C061 30 30 WHITE 27925

AIR MECHANICS & AIR ARMAMENT WORKSHOP 2JZ0 11.2 PORT C061 30 30 WHITE 27925 JOINER BULKHEAD

AIR MECHANICS & AIR ARMAMENT WORKSHOP 2JZ0 8.9 STBD C212 36 36 C061 30 30 WHITE 27925

AIR MECHANICS & AIR ARMAMENT WORKSHOP 2JZ0 13.6 OTHERS C061 30 30 GREY 16076 DADO (900 mm HIGH)

COXWAIN'S SINGLE CABIN 2JZ1 7.6 ST DECK C413 125-150 DK COVERINGCOXWAIN'S SINGLE CABIN 2JZ1 8.2 DECKHEAD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925COXWAIN'S SINGLE CABIN 2JZ1 6.4 FORWARD C212 36 36 C061 30 30 GREY 27875COXWAIN'S SINGLE CABIN 2JZ1 6.9 AFT C212 36 36 C061 30 30 GREY 27875COXWAIN'S SINGLE CABIN 2JZ1 8.9 PORT C212 36 36 C061 30 30 GREY 27875COXWAIN'S SINGLE CABIN 2JZ1 8.9 STBD C212 36 36 C061 30 30 GREY 27875AIR MAINTENANCE CONTROL OFFICE 2JZ2 6.6 ST DECK C413 125-150 DK COVERINGAIR MAINTENANCE CONTROL OFFICE 2JZ2 7.3 DECKHEAD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925AIR MAINTENANCE CONTROL OFFICE 2JZ2 10.5 FORWARD C061 30 30 GREEN 24585 JOINER BULKHEADAIR MAINTENANCE CONTROL OFFICE 2JZ2 11.3 AFT C212 36 36 C061 30 30 GREEN 24585AIR MAINTENANCE CONTROL OFFICE 2JZ2 5.5 PORT C212 36 36 INSULATION NOTE 4 C061 30 30 GREEN 24585AIR MAINTENANCE CONTROL OFFICE 2JZ2 5.5 STBD C212 36 36 C061 30 30 GREEN 24585AIR MAINTENANCE CONTROL OFFICE 2JZ2 5.1 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480MESS NO. 6 2JZ3 19.1 ST DECK C413 125-150 DK COVERINGMESS NO. 6 2JZ3 20.6 DECKHEAD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925MESS NO. 6 2JZ3 10.7 FORWARD C061 30 30 GREY 27875 JOINER BULKHEADMESS NO. 6 2JZ3 11.8 AFT C212 36 36 C061 30 30 GREY 27875MESS NO. 6 2JZ3 14.8 PORT C212 36 36 C061 30 30 GREY 27875MESS NO. 6 2JZ3 13.5 STBD C212 36 36 INSULATION NOTE 4 C061 30 30 GREY 27875MESS NO. 6 2JZ3 13.2 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480

SHINCOM EQUIPMENT ROOM 2KA0 10.0 ST DECK TRAFFIC C413 125-150 C200 750-1000 GREY 36076

SHINCOM EQUIPMENT ROOM 2KA0 3.0 ST DECK NON TRAFFIC

C413 AND C045 C061 30 30 GREY 16076

SHINCOM EQUIPMENT ROOM 2KA0 13.0 DECKHEAD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925SHINCOM EQUIPMENT ROOM 2KA0 15.6 FORWARD C212 36 36 C061 30 30 WHITE 27925SHINCOM EQUIPMENT ROOM 2KA0 12.5 AFT C212 36 36 C061 30 30 WHITE 27925SHINCOM EQUIPMENT ROOM 2KA0 8.8 PORT C212 36 36 C061 30 30 WHITE 27925SHINCOM EQUIPMENT ROOM 2KA0 7.4 STBD C212 36 36 C061 30 30 WHITE 27925GUNNERS STORE (FFH 330 - FFH 335) OR GENERAL STORE NO. 4 (FFH 336 - FFH 341) 2KA1 8.0 ST DECK

TRAFFIC C413 125-150 C200 750-1000 GREY 36076

GUNNERS STORE (FFH 330 - FFH 335) OR GENERAL STORE NO. 4 (FFH 336 - FFH 341) 2KA1 3.1 ST DECK NON

TRAFFICC413 AND

C045 C061 30 30 GREY 16076

GUNNERS STORE (FFH 330 - FFH 335) OR GENERAL STORE NO. 4 (FFH 336 - FFH 341) 2KA1 12.2 DECKHEAD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925

GUNNERS STORE (FFH 330 - FFH 335) OR GENERAL STORE NO. 4 (FFH 336 - FFH 341) 2KA1 10.2 FORWARD C212 36 36 C061 30 30 WHITE 27925

GUNNERS STORE (FFH 330 - FFH 335) OR GENERAL STORE NO. 4 (FFH 336 - FFH 341) 2KA1 11.8 AFT C212 36 36 C061 30 30 WHITE 27925


Primer

DCZ Area M2

Surface1st Coat

µm


Name

Remarks

Rev: C


µm2nd Coat

µm


Finisher


µm3rd Coat

µm1st Coat

µm

GUNNERS STORE (FFH 330 - FFH 335) OR GENERAL STORE NO. 4 (FFH 336 - FFH 341) 2KA1 8.3 PORT C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925

GUNNERS STORE (FFH 330 - FFH 335) OR GENERAL STORE NO. 4 (FFH 336 - FFH 341) 2KA1 9.0 STBD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925

GUNNERS STORE (FFH 330 - FFH 335) OR GENERAL STORE NO. 4 (FFH 336 - FFH 341) 2KA1 8.3 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480

GUNNERS STORE (FFH 330 - FFH 335) OR GENERAL STORE NO. 4 (FFH 336 - FFH 341) 2KA1 12.1 OTHERS C061 30 30 GREY 16076 DADO (900 mm HIGH)

PASSAGEWAY 2KA2 16.9 ST DECK C413 125-150 DK COVERINGPASSAGEWAY 2KA2 16.9 DECKHEAD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925PASSAGEWAY 2KA2 6.3 FORWARD C212 36 36 C061 30 30 GREY 27880PASSAGEWAY 2KA2 4.1 AFT C212 36 36 C061 30 30 GREY 27880PASSAGEWAY 2KA2 27.6 PORT C212 36 36 C061 30 30 GREY 27880PASSAGEWAY 2KA2 34.3 STBD C212 36 36 C061 30 30 GREY 27880PASSAGEWAY 2KA2 3.9 OTHERS C061 30 30 GREY 16076 DADO (150 mm HIGH)

HELO POWER 2KA4 4.0 ST DECK TRAFFIC C413 125-150 C200 750-1000 GREY 36076

HELO POWER 2KA4 2.0 ST DECK NON TRAFFIC

C413 AND C045 C061 OR C177 30 30 GREY 16076

HELO POWER 2KA4 6.6 DECKHEAD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925HELO POWER 2KA4 10.2 FORWARD C212 36 36 C061 30 30 WHITE 27925HELO POWER 2KA4 10.7 AFT C212 36 36 C061 30 30 WHITE 27925HELO POWER 2KA4 4.7 PORT C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925HELO POWER 2KA4 5.0 STBD C212 36 36 C061 30 30 WHITE 27925HELO POWER 2KA4 4.4 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480

EMERGENCY RADIO ROOM 2KB0 9.0 ST DECK TRAFFIC C413 125-150 C200 750-1000 GREY 36076

EMERGENCY RADIO ROOM 2KB0 3.9 ST DECK NON TRAFFIC

C413 AND C045 C061 OR C177 30 30 GREY 16076

EMERGENCY RADIO ROOM 2KB0 12.9 DECKHEAD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925EMERGENCY RADIO ROOM 2KB0 12.5 FORWARD C212 36 36 C061 30 30 WHITE 27925EMERGENCY RADIO ROOM 2KB0 14.1 AFT C212 36 36 C061 30 30 WHITE 27925EMERGENCY RADIO ROOM 2KB0 9.6 PORT C212 36 36 C061 30 30 WHITE 27925EMERGENCY RADIO ROOM 2KB0 7.3 STBD C212 36 36 C061 30 30 WHITE 27925

LSO COMPARTMENT 2KB1 3.0 ST DECK TRAFFIC C413 125-150 C200 750-1000 GREY 36076

LSO COMPARTMENT 2KB1 1.9 ST DECK NON TRAFFIC

C413 AND C045 C061 OR C177 30 30 GREY 16076

LSO COMPARTMENT 2KB1 5.6 DECKHEAD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925LSO COMPARTMENT 2KB1 7.3 FORWARD C212 36 36 C061 30 30 WHITE 27925LSO COMPARTMENT 2KB1 7.8 AFT C212 36 36 C061 30 30 WHITE 27925LSO COMPARTMENT 2KB1 5.9 PORT C212 36 36 C061 30 30 WHITE 27925LSO COMPARTMENT 2KB1 5.9 STBD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925LSO COMPARTMENT 2KB1 5.5 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480

AFTER AC PLANT 2KB2 20.0 ST DECK TRAFFIC C413 125-150 C200 750-1000 GREY 36076

AFTER AC PLANT 2KB2 6.9 ST DECK NON TRAFFIC

C413 AND C045 C061 30 30 GREY 16076

AFTER AC PLANT 2KB2 29.5 DECKHEAD C212 36 36 INSULATION C061 30 30 WHITE 27925AFTER AC PLANT 2KB2 11.0 FORWARD C212 36 36 INSULATION NOTE 5 WHITE 27925AFTER AC PLANT 2KB2 11.0 AFT C212 36 36 INSULATION NOTE 5 C061 30 30 WHITE 27925AFTER AC PLANT 2KB2 20.4 PORT C212 36 36 INSULATION NOTE 5 WHITE 27925AFTER AC PLANT 2KB2 20.2 STBD C212 36 36 INSULATION NOTE 5 WHITE 27925


Primer

DCZ Area M2

Surface1st Coat

µm


Name

Remarks

Rev: C


µm2nd Coat

µm


Finisher


µm3rd Coat

µm1st Coat

µm

AFTER AC PLANT 2KB2 18.9 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480

AFTER AC PLANT 2KB2 19.2 OTHERS C061 30 30 GREY 16076 DADO (900 mm HIGH) EXCEPT OVER PERFORATED METAL.

HELO FUEL/DEFUEL COMPARTMENT 2KY1 5.0 ST DECK TRAFFIC C413 125-150 C200 750-1000 GREY 36076

HELO FUEL/DEFUEL COMPARTMENT 2KY1 1.7 ST DECK NON TRAFFIC

C413 AND C045 C061 OR C177 30 30 GREY 16076

HELO FUEL/DEFUEL COMPARTMENT 2KY1 7.7 DECKHEAD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925HELO FUEL/DEFUEL COMPARTMENT 2KY1 8.6 FORWARD C212 36 36 C061 30 30 WHITE 27925HELO FUEL/DEFUEL COMPARTMENT 2KY1 6.9 AFT C212 36 36 C061 30 30 WHITE 27925HELO FUEL/DEFUEL COMPARTMENT 2KY1 7.7 PORT C212 36 36 C061 30 30 WHITE 27925HELO FUEL/DEFUEL COMPARTMENT 2KY1 7.3 STBD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925HELO FUEL/DEFUEL COMPARTMENT 2KY1 6.8 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480

AFTER SONAR INSTRUMENT SPACE 2KZ0 16.0 ST DECK TRAFFIC C413 125-150 C200 750-1000 GREY 36076

AFTER SONAR INSTRUMENT SPACE 2KZ0 10.5 ST DECK NON TRAFFIC

C413 AND C045 C061 OR C177 30 30 GREY 16076

AFTER SONAR INSTRUMENT SPACE 2KZ0 26.5 DECKHEAD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925AFTER SONAR INSTRUMENT SPACE 2KZ0 15.1 FORWARD C212 36 36 C061 30 30 WHITE 27925AFTER SONAR INSTRUMENT SPACE 2KZ0 15.1 AFT C212 36 36 C061 30 30 WHITE 27925AFTER SONAR INSTRUMENT SPACE 2KZ0 15.6 PORT C061 30 30 WHITE 27925 JOINER BULKHEADAFTER SONAR INSTRUMENT SPACE 2KZ0 14.9 STBD C212 36 36 C061 30 30 WHITE 27925LOBBY 2KZ1 9.0 ST DECK C413 125-150 DK COVERINGLOBBY 2KZ1 9.0 DECKHEAD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925LOBBY 2KZ1 3.8 FORWARD C212 36 36 C061 30 30 GREY 27880LOBBY 2KZ1 3.0 AFT C212 36 36 C061 30 30 GREY 27880LOBBY 2KZ1 19.2 PORT C212 36 36 C061 30 30 GREY 27880LOBBY 2KZ1 22.3 STBD C212 36 36 C061 30 30 GREY 27880LOBBY 2KZ1 2.6 OTHERS C061 30 30 GREY 16076 DADO (150 mm HIGH)

SMALL ARMS MAGAZINE 2KZ2 4.0 ST DECK TRAFFIC C413 125-150 C200 750-1000 GREY 36076

SMALL ARMS MAGAZINE 2KZ2 2.9 ST DECK NON TRAFFIC

C413 AND C045 C061 OR C177 30 30 GREY 16076

SMALL ARMS MAGAZINE 2KZ2 6.5 DECKHEAD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925SMALL ARMS MAGAZINE 2KZ2 11.5 FORWARD C212 36 36 C061 30 30 WHITE 27925SMALL ARMS MAGAZINE 2KZ2 12.5 AFT C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925SMALL ARMS MAGAZINE 2KZ2 4.6 PORT C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925SMALL ARMS MAGAZINE 2KZ2 4.3 STBD C212 36 36 C061 30 30 WHITE 27925SMALL ARMS MAGAZINE 2KZ2 4.3 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480SMALL ARMS MAGAZINE 2KZ2 9.7 OTHERS C061 30 30 GREY 16076 DADO (900 mm HIGH)

TAU COMPARTMENT 2KZ3 6.0 ST DECK TRAFFIC C413 125-150 C200 750-1000 GREY 36076

TAU COMPARTMENT 2KZ3 1.4 ST DECK NON TRAFFIC

C413 AND C045 C061 OR C177 30 30 GREY 16076

TAU COMPARTMENT 2KZ3 8.0 DECKHEAD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925TAU COMPARTMENT 2KZ3 8.1 FORWARD C212 36 36 C061 30 30 WHITE 27925TAU COMPARTMENT 2KZ3 8.7 AFT C212 36 36 C061 30 30 WHITE 27925TAU COMPARTMENT 2KZ3 6.9 PORT C212 36 36 C061 30 30 WHITE 27925TAU COMPARTMENT 2KZ3 7.4 STBD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925TAU COMPARTMENT 2KZ3 6.9 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480PASSAGEWAY 2LA0 12.4 ST DECK C413 125-150 DK COVERINGPASSAGEWAY 2LA0 13.3 DECKHEAD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925PASSAGEWAY 2LA0 N/A FORWARD C212 36 36 C061 30 30 GREY 27880 SEE DAMAGE CONTROL LOBBYPASSAGEWAY 2LA0 4.1 AFT C212 36 36 C061 30 30 GREY 27880PASSAGEWAY 2LA0 27.9 PORT C212 36 36 C061 30 30 GREY 27880


Primer

DCZ Area M2

Surface1st Coat

µm


Name

Remarks

Rev: C


µm2nd Coat

µm


Finisher


µm3rd Coat

µm1st Coat

µm

PASSAGEWAY 2LA0 15.9 STBD C212 36 36 C061 30 30 GREY 27880PASSAGEWAY 2LA0 2.6 OTHERS C061 30 30 GREY 16076 DADO (150 mm HIGH)DAMAGE CONTROL LOBBY 2LA0 27.3 ST DECK C413 125-150 DK COVERINGDAMAGE CONTROL LOBBY 2LA0 29.5 DECKHEAD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925DAMAGE CONTROL LOBBY 2LA0 22.0 FORWARD C212 36 36 C061 30 30 GREY 27880DAMAGE CONTROL LOBBY 2LA0 18.1 AFT C212 36 36 C061 30 30 GREY 27880DAMAGE CONTROL LOBBY 2LA0 3.5 PORT C212 36 36 C061 30 30 GREY 27880DAMAGE CONTROL LOBBY 2LA0 13.8 STBD C212 36 36 C061 30 30 GREY 27880DC SECTION BASE NO. 2 2LA1 9.1 ST DECK C413 125-150 DK COVERINGDC SECTION BASE NO. 2 2LA1 10.5 DECKHEAD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925DC SECTION BASE NO. 2 2LA1 7.7 FORWARD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925DC SECTION BASE NO. 2 2LA1 7.7 AFT C212 36 36 C061 30 30 WHITE 27925DC SECTION BASE NO. 2 2LA1 9.4 PORT C212 36 36 C061 30 30 WHITE 27925DC SECTION BASE NO. 2 2LA1 10.1 STBD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925DC SECTION BASE NO. 2 2LA1 9.4 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480DAMAGE CONTROL STORE (FFH 330 - FFH 335) OR GUNNERS STORE (FFH 336 - FFH 341) 2LA2 6.0 ST DECK

TRAFFIC C413 125-150 C200 750-1000 GREY 36076

DAMAGE CONTROL STORE (FFH 330 - FFH 335) OR GUNNERS STORE (FFH 336 - FFH 341) 2LA2 2.6 ST DECK NON

TRAFFICC413 AND

C045 C061 OR C177 30 30 GREY 16076

DAMAGE CONTROL STORE (FFH 330 - FFH 335) OR GUNNERS STORE (FFH 336 - FFH 341) 2LA2 9.6 DECKHEAD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925

DAMAGE CONTROL STORE (FFH 330 - FFH 335) OR GUNNERS STORE (FFH 336 - FFH 341) 2LA2 10.4 FORWARD C212 36 36 C061 30 30 WHITE 27925

DAMAGE CONTROL STORE (FFH 330 - FFH 335) OR GUNNERS STORE (FFH 336 - FFH 341) 2LA2 10.4 AFT C212 36 36 C061 30 30 WHITE 27925

DAMAGE CONTROL STORE (FFH 330 - FFH 335) OR GUNNERS STORE (FFH 336 - FFH 341) 2LA2 7.5 PORT C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925

DAMAGE CONTROL STORE (FFH 330 - FFH 335) OR GUNNERS STORE (FFH 336 - FFH 341) 2LA2 6.8 STBD C212 36 36 C061 30 30 WHITE 27925

DAMAGE CONTROL STORE (FFH 330 - FFH 335) OR GUNNERS STORE (FFH 336 - FFH 341) 2LA2 6.9 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480

DAMAGE CONTROL STORE (FFH 330 - FFH 335) OR GUNNERS STORE (FFH 336 - FFH 341) 2LA2 10.8 OTHERS C061 30 30 GREY 16076 DADO (900 mm HIGH)

AIR LOCK 2LB1 1.7 ST DECK TRAFFIC C413 125-150 C200 750-1000 GREY 36076

AIR LOCK 2LB1 3.0 ST DECK NON TRAFFIC

C413 AND C045 C061 OR C177 30 30 GREY 16076

AIR LOCK 2LB1 5.5 DECKHEAD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925AIR LOCK 2LB1 7.7 FORWARD C212 36 36 C061 30 30 GREY 27880AIR LOCK 2LB1 8.2 AFT C212 36 36 C061 30 30 GREY 27880AIR LOCK 2LB1 4.4 PORT C212 36 36 C061 30 30 GREY 27880AIR LOCK 2LB1 6.0 STBD C212 36 36 INSULATION NOTE 4 C061 30 30 GREY 27880AIR LOCK 2LB1 5.0 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480AIR LOCK 2LB1 8.2 OTHERS C061 30 30 GREY 16076 DADO (150 mm HIGH)F.F. EQUIP. STORE (FFH 330 - FFH 335) OR F.F. EQUIP. AND DC STORE (FFH 336 - FFH 341) 2LB2 6.0 ST DECK

TRAFFIC C413 125-150 C200 750-1000 GREY 36076

F.F. EQUIP. STORE (FFH 330 - FFH 335) OR F.F. EQUIP. AND DC STORE (FFH 336 - FFH 341) 2LB2 3.0 ST DECK NON

TRAFFICC413 AND

C045 C061 OR C177 30 30 GREY 16076

F.F. EQUIP. STORE (FFH 330 - FFH 335) OR F.F. EQUIP. AND DC STORE (FFH 336 - FFH 341) 2LB2 10.0 DECKHEAD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925

F.F. EQUIP. STORE (FFH 330 - FFH 335) OR F.F. EQUIP. AND DC STORE (FFH 336 - FFH 341) 2LB2 10.4 FORWARD C212 36 36 C061 30 30 WHITE 27925

F.F. EQUIP. STORE (FFH 330 - FFH 335) OR F.F. EQUIP. AND DC STORE (FFH 336 - FFH 341) 2LB2 10.4 AFT C212 36 36 C061 30 30 WHITE 27925


Primer

DCZ Area M2

Surface1st Coat

µm


Name

Remarks

Rev: C


µm2nd Coat

µm


Finisher


µm3rd Coat

µm1st Coat

µm

F.F. EQUIP. STORE (FFH 330 - FFH 335) OR F.F. EQUIP. AND DC STORE (FFH 336 - FFH 341) 2LB2 7.5 PORT C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925

F.F. EQUIP. STORE (FFH 330 - FFH 335) OR F.F. EQUIP. AND DC STORE (FFH 336 - FFH 341) 2LB2 7.7 STBD C212 36 36 C061 30 30 WHITE 27925

F.F. EQUIP. STORE (FFH 330 - FFH 335) OR F.F. EQUIP. AND DC STORE (FFH 336 - FFH 341) 2LB2 6.9 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480

F.F. EQUIP. STORE (FFH 330 - FFH 335) OR F.F. EQUIP. AND DC STORE (FFH 336 - FFH 341) 2LB2 11.3 OTHERS C061 30 30 GREY 16076 DADO (900 mm HIGH)

RAST EQUIPMENT ROOM 2LY0 12.0 ST DECK TRAFFIC C413 125-150 C200 750-1000 GREY 36076

RAST EQUIPMENT ROOM 2LY0 8.7 ST DECK NON TRAFFIC

C413 AND C045 C061 OR C177 30 30 GREY 16076

RAST EQUIPMENT ROOM 2LY0 20.7 DECKHEAD C212 36 36 INSULATION C061 30 30 WHITE 27925RAST EQUIPMENT ROOM 2LY0 13.0 FORWARD C212 36 36 INSULATION NOTE 5 WHITE 27925RAST EQUIPMENT ROOM 2LY0 13.0 AFT C212 36 36 INSULATION NOTE 5 WHITE 27925RAST EQUIPMENT ROOM 2LY0 13.9 PORT C212 36 36 INSULATION NOTE 5 WHITE 27925RAST EQUIPMENT ROOM 2LY0 13.9 STBD C212 36 36 INSULATION NOTE 5 WHITE 27925RAST EQUIPMENT ROOM 2LY0 16.3 OTHERS C061 30 30 GREY 16076 DADO (900 mm HIGH)

RAST EQUIPMENT ROOM 2LY0 3.0 ST DECK TRAFFIC C413 125-150 C200 750-1000 GREY 36076

RAST EQUIPMENT ROOM 2LY0 1.3 ST DECK NON TRAFFIC

C413 AND C045 C061 OR C177 30 30 GREY 16076

RAST EQUIPMENT ROOM 2LY0 4.3 DECKHEAD C212 36 36 INSULATION C061 30 30 WHITE 27925RAST EQUIPMENT ROOM 2LY0 4.5 FORWARD C212 36 36 C061 30 30 WHITE 27925RAST EQUIPMENT ROOM 2LY0 4.5 AFT C212 36 36 INSULATION NOTE 5 WHITE 27925RAST EQUIPMENT ROOM 2LY0 7.2 PORT C212 36 36 INSULATION NOTE 5 WHITE 27925RAST EQUIPMENT ROOM 2LY0 7.7 STBD C212 36 36 INSULATION NOTE 5 WHITE 27925AFTER CLEANSING STATION CLEANSE 2LY1 7.1 ST DECK C413 125-150 DK COVERINGAFTER CLEANSING STATION CLEANSE 2LY1 8.3 DECKHEAD C212 36 36 INSULATION C021 100 WHITE

AFTER CLEANSING STATION (CLEANSE) FFH330 2LY1 8.2 FORWARD C212 36 36 C418 50 50 WHITE

AFTER CLEANSING STATION (CLEANSE) FFH 331 TO FFH341 2LY1 8.2 FORWARD C021 100 C021 100 WHITE FFH-331 - FFH-341 ONLY

AFTER CLEANSING STATION (CLEANSE) FFH330 2LY1 7.2 AFT C212 36 36 C418 100 WHITE

AFTER CLEANSING STATION (CLEANSE) FFH 331 TO FFH341 2LY1 7.2 AFT C021 100 C021 100 WHITE FFH-331 - FFH-341 ONLY

AFTER CLEANSING STATION (CLEANSE) FFH330 2LY1 8.7 PORT C212 36 36 C418 50 50 WHITE

AFTER CLEANSING STATION (CLEANSE) FFH 331 TO FFH341 2LY1 8.7 PORT C021 100 C021 100 WHITE FFH-331 - FFH-341 ONLY

AFTER CLEANSING STATION CLEANSE 2LY1 8.1 STBD C212 36 36 INSULATION C021 100 WHITE AFTER CLEANSING STATION CLEANSE 2LY1 7.5 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480

SMALL ARMS LOCKER 2LZ0 4.1 ST DECK TRAFFIC C413 125-150 C200 750-1000 GREY 36076

SMALL ARMS LOCKER 2LZ0 3.0 ST DECK NON TRAFFIC

C413 AND C045 C061 OR C177 30 30 GREY 16076

SMALL ARMS LOCKER 2LZ0 7.1 DECKHEAD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925SMALL ARMS LOCKER 2LZ0 7.5 FORWARD C212 36 36 C061 30 30 WHITE 27925SMALL ARMS LOCKER 2LZ0 8.2 AFT C212 36 36 C061 30 30 WHITE 27925SMALL ARMS LOCKER 2LZ0 7.6 PORT C212 36 36 C061 30 30 WHITE 27925SMALL ARMS LOCKER 2LZ0 7.1 STBD C212 36 36 C061 30 30 WHITE 27925


Primer

DCZ Area M2

Surface1st Coat

µm


Name

Remarks

Rev: C


µm2nd Coat

µm


Finisher


µm3rd Coat

µm1st Coat

µm

DIVING GEAR STORE 2LZ1 6.0 ST DECK TRAFFIC C413 125-150 C200 750-1000 GREY 36076

DIVING GEAR STORE 2LZ1 7.2 ST DECK NON TRAFFIC

C413 AND C045 C061 OR C177 30 30 GREY 16076

DIVING GEAR STORE 2LZ1 13.2 DECKHEAD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925DIVING GEAR STORE 2LZ1 6.0 FORWARD C212 36 36 C061 30 30 WHITE 27925DIVING GEAR STORE 2LZ1 7.0 AFT C212 36 36 C061 30 30 WHITE 27925DIVING GEAR STORE 2LZ1 16.5 PORT C212 36 36 C061 30 30 WHITE 27925DIVING GEAR STORE 2LZ1 16.5 STBD C212 36 36 C061 30 30 WHITE 27925DIVING GEAR STORE 2LZ1 14.7 OTHERS C061 30 30 GREY 16076 DADO (900 mm HIGH)

AIR LOCK 2LZ2 1.0 ST DECK TRAFFIC C413 125-150 C200 750-1000 GREY 36076

AIR LOCK 2LZ2 0.6 ST DECK NON TRAFFIC

C413 AND C045 C061 OR C177 30 30 GREY 16076

AIR LOCK 2LZ2 1.6 DECKHEAD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925AIR LOCK 2LZ2 3.0 FORWARD C212 36 36 C061 30 30 GREY 27880AIR LOCK 2LZ2 3.0 AFT C212 36 36 C061 30 30 GREY 27880AIR LOCK 2LZ2 4.1 PORT C212 36 36 C061 30 30 GREY 27880AIR LOCK 2LZ2 4.1 STBD C212 36 36 C061 30 30 GREY 27880AIR LOCK 2LZ2 0.8 OTHERS C061 30 30 GREY 16076 DADO (150 mm HIGH)AFTER CLEANSING STATION STRIP 2LZ3 6.6 ST DECK C413 125-150 DK COVERINGAFTER CLEANSING STATION STRIP 2LZ3 7.8 DECKHEAD C212 36 36 INSULATION C021 100 WHITEAFTER CLEANSING STATION (STRIP) FFH330 2LZ3 7.2 FORWARD C212 36 36 C418 50 50 WHITEAFTER CLEANSING STATION (STRIP) FFH 331 TO FFH341 2LZ3 7.2 FORWARD C021 100 C021 100 WHITE FFH-331 - FFH-341 ONLY

AFTER CLEANSING STATION (STRIP) FFH330 2LZ3 7.2 AFT C212 36 36 C418 50 50 WHITEAFTER CLEANSING STATION (STRIP) FFH 331 TO FFH341 2LZ3 7.2 AFT C021 100 C021 100 WHITE FFH-331 - FFH-341 ONLY

AFTER CLEANSING STATION (STRIP) FFH330 2LZ3 7.8 PORT C212 36 36 C418 50 50 WHITEAFTER CLEANSING STATION (STRIP) FFH 331 TO FFH341 2LZ3 7.8 PORT C021 100 C021 100 WHITE FFH-331 - FFH-341 ONLY

AFTER CLEANSING STATION STRIP 2LZ3 8.4 STBD C212 36 36 INSULATION C021 100 WHITE AFTER CLEANSING STATION STRIP 2LZ3 7.8 SHELL EXT 76 C045 C411 30 30 30 GREY 26480

SHIPWRIGHTS WORKSHOP 2LZ4 10.0 ST DECK TRAFFIC C413 125-150 C200 750-1000 GREY 36076

SHIPWRIGHTS WORKSHOP 2LZ4 10.0 ST DECK NON TRAFFIC

C413 AND C045 C061 OR C177 30 30 GREY 16076

SHIPWRIGHTS WORKSHOP 2LZ4 22.4 DECKHEAD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925SHIPWRIGHTS WORKSHOP 2LZ4 10.5 FORWARD C212 36 36 C061 30 30 WHITE 27925SHIPWRIGHTS WORKSHOP 2LZ4 10.5 AFT C212 36 36 C061 30 30 WHITE 27925SHIPWRIGHTS WORKSHOP 2LZ4 18.0 PORT C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925SHIPWRIGHTS WORKSHOP 2LZ4 19.0 STBD C212 36 36 C061 30 30 WHITE 27925SHIPWRIGHTS WORKSHOP 2LZ4 18.0 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480SHIPWRIGHTS WORKSHOP 2LZ4 17.5 OTHERS C061 30 30 GREY 16076 DADO (900 mm HIGH)

LOBBY/FIRE FIGHTING SHELTER 2MA0 14.5 ST DECK TRAFFIC C413 125-150 C200 750-1000 GREY 36076

LOBBY/FIRE FIGHTING SHELTER 2MA0 4.0 ST DECK NON TRAFFIC

C413 AND C045 C061 OR C177 30 30 GREY 16076

LOBBY/FIRE FIGHTING SHELTER 2MA0 18.8 DECKHEAD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925LOBBY/FIRE FIGHTING SHELTER 2MA0 18.1 FORWARD C212 36 36 C061 30 30 WHITE 27925LOBBY/FIRE FIGHTING SHELTER 2MA0 18.1 AFT C212 36 36 C061 30 30 WHITE 27925LOBBY/FIRE FIGHTING SHELTER 2MA0 33.0 PORT C212 36 36 C061 30 30 WHITE 27925LOBBY/FIRE FIGHTING SHELTER 2MA0 16.5 STBD C212 36 36 C061 30 30 WHITE 27925


Primer

DCZ Area M2

Surface1st Coat

µm


Name

Remarks

Rev: C


µm2nd Coat

µm


Finisher


µm3rd Coat

µm1st Coat

µm

LOBBY/FIRE FIGHTING SHELTER 2MA0 3.5 OTHERS C061 30 30 GREY 16076 DADO (150 mm HIGH)CLEANSING STATION NO. 2 UNDRESS 2MA1 6.5 ST DECK C413 125-150 DK COVERING

CLEANSING STATION NO. 2 UNDRESS 2MA1 7.3 DECKHEAD C212 36 36 INSULATION C021 100 WHITE

CLEAR OF FIBERGLASS LINING. APPLY 2 COATS 3 µm OF C021 TO THE DOUBLE LAYER OF FIBREGLASS, COLOUR TO BE WHITE.

AFTER CLEANSING STATION UNDRESS 2MA1 9.0 FORWARD C021 100 C021 100 WHITEAFTER CLEANSING STATION UNDRESS 2MA1 10.0 AFT C021 100 C021 100 WHITEAFTER CLEANSING STATION UNDRESS 2MA1 5.3 PORT C021 100 C021 100 WHITE

AFTER CLEANSING STATION UNDRESS 2MA1 5.3 STBD C212 36 36 INSULATION C418 50 50 WHITE

CLEAR OF FIBERGLASS LINING. APPLY 2 COATS 3 µm OF C021 TO THE DOUBLE LAYER OF FIBREGLASS, COLOUR TO BE WHITE.

AFTER CLEANSING STATION UNDRESS 2MA1 5.3 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480

CBRN FILTER COMPARTMENT NO. 4 2MA2 3.6 ST DECK TRAFFIC C413 125-150 C200 750-1000 GREY 36076

CBRN FILTER COMPARTMENT NO. 4 2MA2 6.0 ST DECK NON TRAFFIC

C413 AND C045 C061 OR C177 30 30 GREY 16076

CBRN FILTER COMPARTMENT NO. 4 2MA2 11.6 DECKHEAD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925CBRN FILTER COMPARTMENT NO. 4 2MA2 10.0 FORWARD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925CBRN FILTER COMPARTMENT NO. 4 2MA2 9.6 AFT C212 36 36 C061 30 30 WHITE 27925CBRN FILTER COMPARTMENT NO. 4 2MA2 10.0 PORT C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925CBRN FILTER COMPARTMENT NO. 4 2MA2 9.0 STBD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925CBRN FILTER COMPARTMENT NO. 4 2MA2 10.0 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480CBRN FILTER COMPARTMENT NO. 4 2MA2 11.2 OTHERS C061 30 30 GREY 16076 DADO (900 mm HIGH)

DECK STORE NO. 3 2MZ0 17.3 ST DECK TRAFFIC C413 125-150 C200 750-1000 GREY 36076

DECK STORE NO. 3 2MZ0 7.4 ST DECK NON TRAFFIC

C413 AND C045 C061 OR C177 30 30 GREY 16076

DECK STORE NO. 3 2MZ0 28.1 DECKHEAD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925DECK STORE NO. 3 2MZ0 17.8 FORWARD C212 36 36 C061 30 30 WHITE 27925DECK STORE NO. 3 2MZ0 20.0 AFT C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925DECK STORE NO. 3 2MZ0 23.1 PORT C212 36 36 C061 30 30 WHITE 27925DECK STORE NO. 3 2MZ0 23.1 STBD C212 36 36 C061 30 30 WHITE 27925DECK STORE NO. 3 2MZ0 10.0 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480DECK STORE NO. 3 2MZ0 29.3 OTHERS C061 30 30 GREY 16076 DADO (900 mm HIGH)

TOWED ARRAY EQUIPMENT ROOM 2MZ1 10.2 ST DECK TRAFFIC C413 125-150 C200 750-1000 GREY 36076

TOWED ARRAY EQUIPMENT ROOM 2MZ1 23.8 ST DECK NON TRAFFIC

C413 AND C045 C061 OR C177 30 30 GREY 16076

TOWED ARRAY EQUIPMENT ROOM 2MZ1 41.6 DECKHEAD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925TOWED ARRAY EQUIPMENT ROOM 2MZ1 13.3 FORWARD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925TOWED ARRAY EQUIPMENT ROOM 2MZ1 13.0 AFT C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925TOWED ARRAY EQUIPMENT ROOM 2MZ1 21.3 PORT C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925TOWED ARRAY EQUIPMENT ROOM 2MZ1 24.0 STBD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925TOWED ARRAY EQUIPMENT ROOM 2MZ1 37.0 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480TOWED ARRAY EQUIPMENT ROOM 2MZ1 21.6 OTHERS C061 30 30 GREY 16076 DADO (900 mm HIGH)

TORPEDO DECOY & XBT/XSV EQUIPMENT ROOM 2MZ2 18.0 ST DECK TRAFFIC C413 125-150 C200 750-1000 GREY 36076


Primer

DCZ Area M2

Surface1st Coat

µm


Name

Remarks

Rev: C


µm2nd Coat

µm


Finisher


µm3rd Coat

µm1st Coat

µm

TORPEDO DECOY & XBT/XSV EQUIPMENT ROOM 2MZ2 4.9 ST DECK NON TRAFFIC

C413 AND C045 C061 OR C177 30 30 GREY 16076

TORPEDO DECOY & XBT/XSV EQUIPMENT ROOM 2MZ2 28.0 DECKHEAD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925

TORPEDO DECOY & XBT/XSV EQUIPMENT ROOM 2MZ2 14.0 FORWARD C212 36 36 C061 30 30 WHITE 27925

TORPEDO DECOY & XBT/XSV EQUIPMENT ROOM 2MZ2 13.0 AFT C212 36 36 NOTE 4 C061 30 30 WHITE 27925 PART INSULATION

TORPEDO DECOY & XBT/XSV EQUIPMENT ROOM 2MZ2 20.0 PORT C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925

TORPEDO DECOY & XBT/XSV EQUIPMENT ROOM 2MZ2 14.6 STBD C212 36 36 C061 30 30 WHITE 27925

TORPEDO DECOY & XBT/XSV EQUIPMENT ROOM 2MZ2 32.0 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480

TORPEDO DECOY & XBT/XSV EQUIPMENT ROOM 2MZ2 19.7 OTHERS C061 30 30 GREY 16076 DADO (900 mm HIGH)

XBT/XSV STORE 2MZ2 1.0 ST DECK TRAFFIC C413 125-150 C200 750-1000 GREY 36076

XBT/XSV STORE 2MZ2 1.9 ST DECK NON TRAFFIC

C413 AND C045 C061 OR C177 30 30 GREY 16076

XBT/XSV STORE 2MZ2 5.1 DECKHEAD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925XBT/XSV STORE 2MZ2 5.3 FORWARD C212 36 36 C061 30 30 WHITE 27925XBT/XSV STORE 2MZ2 6.0 AFT C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925XBT/XSV STORE 2MZ2 5.0 PORT C212 36 36 C061 30 30 WHITE 27925XBT/XSV STORE 2MZ2 4.0 STBD C212 36 36 C061 30 30 WHITE 27925XBT/XSV STORE 2MZ2 5.3 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480XBT/XSV STORE 2MZ2 6.2 OTHERS C061 30 30 GREY 16076 DADO (900 mm HIGH)

GENERAL STORE NO.1 MAA 14.2 ST DECK TRAFFIC C413 125-150 C200 750-1000 GREY 36076

GENERAL STORE NO.1 MAA 2.0 ST DECK NON TRAFFIC

C413 AND C045 C061 OR C177 30 30 GREY 16076

GENERAL STORE NO.1 MAA 28.6 DECKHEAD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925GENERAL STORE NO.1 MAA 2.2 FORWARD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925GENERAL STORE NO.1 MAA 9.2 AFT C212 36 36 C061 30 30 WHITE 27925GENERAL STORE NO.1 MAA 12.4 PORT C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925GENERAL STORE NO.1 MAA 12.4 STBD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925GENERAL STORE NO.1 MAA 24.8 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480GENERAL STORE NO.1 MAA 14.4 OTHERS C061 30 30 GREY 16076 DADO (900mm HIGH)

ROPE STORE & BOSUNS WORKSHOP MAZ 30.3 ST DECK TRAFFIC C413 125-150 C200 750-1000 GREY 36076

ROPE STORE & BOSUNS WORKSHOP MAZ 3.1 ST DECK NON TRAFFIC

C413 AND C045 C061 OR C177 30 30 GREY 16076

ROPE STORE & BOSUNS WORKSHOP MAZ 45.1 DECKHEAD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925ROPE STORE & BOSUNS WORKSHOP MAZ 9.0 FORWARD C212 36 36 C061 30 30 WHITE 27925ROPE STORE & BOSUNS WORKSHOP MAZ 15.0 AFT C212 36 36 C061 30 30 WHITE 27925ROPE STORE & BOSUNS WORKSHOP MAZ 11.6 PORT C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925ROPE STORE & BOSUNS WORKSHOP MAZ 11.6 STBD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925ROPE STORE & BOSUNS WORKSHOP MAZ 23.2 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480ROPE STORE & BOSUNS WORKSHOP MAZ 2.1 OTHERS C061 30 30 GREY 16076 DADO (900mm HIGH)

COMMUNICATIONS EQUIPMENT ROOM 1DA 17.8 ST DECK TRAFFIC C413 125-150 C200 750-1000 GREY 36076


Primer

DCZ Area M2

Surface1st Coat

µm


Name

Remarks

Rev: C


µm2nd Coat

µm


Finisher


µm3rd Coat

µm1st Coat

µm

COMMUNICATIONS EQUIPMENT ROOM 1DA 20.6 ST DECK NON TRAFFIC

C413 AND C045 C061 OR C177 30 30 GREY 16076

COMMUNICATIONS EQUIPMENT ROOM 1DA 41.5 DECKHEAD C212 36 36 NOTE 4 C061 30 30 WHITE 27925 PART INSULATIONCOMMUNICATIONS EQUIPMENT ROOM 1DA 28.7 FORWARD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925COMMUNICATIONS EQUIPMENT ROOM 1DA 28.4 AFT C212 36 36 C061 30 30 WHITE 27925COMMUNICATIONS EQUIPMENT ROOM 1DA 10.3 PORT C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925COMMUNICATIONS EQUIPMENT ROOM 1DA 10.6 STBD C212 36 36 C061 30 30 WHITE 27925COMMUNICATIONS EQUIPMENT ROOM 1DA 26.6 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480

PASSAGEWAY 1DA2 21.5 ST DECK TRAFFIC C413 125-150 C200 750-1000 GREY 36076

PASSAGEWAY 1DA2 21.4 ST DECK NON TRAFFIC

C413 AND C045 C061 OR C177 30 30 GREY 16076

PASSAGEWAY 1DA2 46.3 DECKHEAD C212 36 36 C061 30 30 WHITE 27925PASSAGEWAY 1DA2 8.4 FORWARD C212 36 36 C061 30 30 GREY 27880PASSAGEWAY 1DA2 9.2 AFT C212 36 36 C061 30 30 GREY 27880PASSAGEWAY 1DA2 42.0 PORT C212 36 36 C061 30 30 GREY 27880PASSAGEWAY 1DA2 53.0 STBD C212 36 36 C061 30 30 GREY 27880PASSAGEWAY 1DA2 55.3 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480PASSAGEWAY 1DA2 6.1 OTHERS C061 30 30 GREY 16076 DADO (150mm HIGH)COMMUNICATIONS CONTROL ROOM 1DB 66.8 ST DECK C413 125-150 DK COVERINGCOMMUNICATIONS CONTROL ROOM 1DB 72.1 DECKHEAD C212 36 36 INSULATION NOTE 5 WHITE 27925COMMUNICATIONS CONTROL ROOM 1DB 49.0 FORWARD C212 36 36 INSULATION NOTE 5 WHITE 27925COMMUNICATIONS CONTROL ROOM 1DB 37.0 AFT C212 36 36 INSULATION NOTE 5 WHITE 27925COMMUNICATIONS CONTROL ROOM 1DB 11.8 PORT C212 36 36 INSULATION NOTE 5 WHITE 27925COMMUNICATIONS CONTROL ROOM 1DB 16.8 STBD C212 36 36 INSULATION NOTE 5 WHITE 27925COMMUNICATIONS CONTROL ROOM 1DB 15.6 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480COMMUNICATIONS CONTROL ROOM 1DB 6.2 OTHERS C061 30 30 GREY 16076 DADO (150mm HIGH)

COMMAND CONTROL EQUIPMENT ROOM NO. 1 1DC0 10.3 ST DECK TRAFFIC C413 125-150 C200 750-1000 GREY 36076

COMMAND CONTROL EQUIPMENT ROOM NO. 1 1DC0 7.3 ST DECK NON TRAFFIC

C413 AND C045 C061 OR C177 30 30 GREY 16076

COMMAND CONTROL EQUIPMENT ROOM NO. 1 1DC0 19.0 DECKHEAD C212 36 36 INSULATION C061 30 30 WHITE 27925

COMMAND CONTROL EQUIPMENT ROOM NO. 1 1DC0 12.1 FORWARD C212 36 36 INSULATION NOTE 5 WHITE 27925

COMMAND CONTROL EQUIPMENT ROOM NO. 1 1DC0 12.1 AFT C212 36 36 INSULATION NOTE 5 WHITE 27925

COMMAND CONTROL EQUIPMENT ROOM NO. 1 1DC0 11.0 PORT C212 36 36 INSULATION NOTE 5 WHITE 27925

COMMAND CONTROL EQUIPMENT ROOM NO. 1 1DC0 11.0 STBD C212 36 36 INSULATION NOTE 5 WHITE 27925

CO'S CABIN 1DC1 10.4 ST DECK C413 125-150 DK COVERINGCO'S CABIN 1DC1 11.2 DECKHEAD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925CO'S CABIN 1DC1 12.8 FORWARD C212 36 36 C061 30 30 GREY 27886 LININGCO'S CABIN 1DC1 12.9 AFT C061 30 30 GREY 27886 JOINER BULKHEADCO'S CABIN 1DC1 5.3 PORT C212 36 36 C061 30 30 GREY 27886 LININGCO'S CABIN 1DC1 6.4 STBD C212 36 36 INSULATION C061 30 30 GREY 27886 LININGCO'S CABIN 1DC1 5.9 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480

ELECTRONICS MAINTENANCE ROOM 1DC2 2.6 ST DECK TRAFFIC C413 125-150 C200 750-1000 GREY 36076

ELECTRONICS MAINTENANCE ROOM 1DC2 3.3 ST DECK NON TRAFFIC

C413 AND C045 C061 OR C177 30 30 GREY 16076

ELECTRONICS MAINTENANCE ROOM 1DC2 6.4 DECKHEAD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925


Primer

DCZ Area M2

Surface1st Coat

µm


Name

Remarks

Rev: C


µm2nd Coat

µm


Finisher


µm3rd Coat

µm1st Coat

µm

ELECTRONICS MAINTENANCE ROOM 1DC2 6.0 FORWARD C212 36 36 C061 30 30 WHITE 27925ELECTRONICS MAINTENANCE ROOM 1DC2 6.0 AFT C212 36 36 C061 30 30 WHITE 27925ELECTRONICS MAINTENANCE ROOM 1DC2 7.3 PORT C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925ELECTRONICS MAINTENANCE ROOM 1DC2 7.3 STBD C212 36 36 C061 30 30 WHITE 27925

DECK STORE NO. 1 1DX2 1.6 ST DECK TRAFFIC C413 125-150 C200 750-1000 GREY 36076

DECK STORE NO. 1 1DX2 2.8 ST DECK NON TRAFFIC

C413 AND C045 C061 OR C177 30 30 GREY 16076

DECK STORE NO. 1 1DX2 4.8 DECKHEAD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925DECK STORE NO. 1 1DX2 6.0 FORWARD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925DECK STORE NO. 1 1DX2 6.0 AFT C212 36 36 C061 30 30 WHITE 27925DECK STORE NO. 1 1DX2 5.5 PORT C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925DECK STORE NO. 1 1DX2 5.5 STBD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925DECK STORE NO. 1 1DX2 7.6 OTHERS C061 30 30 GREY 16076 DADO (900mm HIGH)SO'S CABIN 1DY1 8.8 ST DECK C413 125-150 DK COVERINGSO'S CABIN 1DY1 9.5 DECKHEAD C212 36 36 NOTE 4 C061 30 30 WHITE 27925 PART INSULATIONSO'S CABIN 1DY1 6.0 FORWARD C212 36 36 C061 30 30 GREY 27886 LININGSO'S CABIN 1DY1 5.6 AFT C061 30 30 GREY 27886 JOINER BULKHEADSO'S CABIN 1DY1 10.2 PORT C061 30 30 GREY 27886 JOINER BULKHEADSO'S CABIN 1DY1 11.0 STBD C212 36 36 C061 30 30 GREY 27886 LININGAIR LOCK 1DY2 2.9 ST DECK C413 125-150 DKCOVERINGAIR LOCK 1DY2 3.1 DECKHEAD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925AIR LOCK 1DY2 6.0 FORWARD C212 36 36 C061 30 30 GREY 27880AIR LOCK 1DY2 6.0 AFT C212 36 36 C061 30 30 GREY 27880AIR LOCK 1DY2 3.7 PORT C212 36 36 INSULATION NOTE 4 C061 30 30 GREY 27880AIR LOCK 1DY2 3.7 STBD C212 36 36 INSULATION NOTE 4 C061 30 30 GREY 27880AIR LOCK 1DY2 1.1 OTHERS C061 30 30 GREY 16076 DADO (150mm HIGH)CO'S/SO'S WASHPLACE 1DY3 4.8 ST DECK C413 125-150 DK COVERING GREY 27880CO'S/SO'S WASHPLACE 1DY3 5.2 DECKHEAD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925CO'S/SO'S WASHPLACE 1DY3 3.2 FORWARD C212 36 36 C061 30 30 GREY 27880 SHOWER AREACO'S/SO'S WASHPLACE 1DY3 2.3 AFT C061 30 30 GREY 27880 JOINER BULKHEADCO'S/SO'S WASHPLACE 1DY3 10.4 PORT C212 36 36 C061 30 30 GREY 27880CO'S/SO'S WASHPLACE 1DY3 13.2 STBD C061 30 30 GREY 27880 JOINER BULKHEADLOBBY(AFT) 1DZ0 22.5 ST DECK C413 125-150 DK COVERINGLOBBY(AFT) 1DZ0 26.1 DECKHEAD C212 36 36 NOTE 4 C061 30 30 WHITE 27925 PART INSULATIONLOBBY(AFT) 1DZ0 12.9 FORWARD C212 36 36 C061 30 30 GREY 27880LOBBY(AFT) 1DZ0 18.1 AFT C212 36 36 C061 30 30 GREY 27880LOBBY(AFT) 1DZ0 13.8 PORT C212 36 36 C061 30 30 GREY 27880LOBBY(AFT) 1DZ0 18.4 STBD C061 30 30 GREY 27880 JOINER BULKHEADLOBBY(AFT) 1DZ0 3.5 OTHERS C061 30 30 GREY 16076 DADO (150mm HIGH)LOBBY(CENTRE) 1DZ0 5.6 ST DECK C413 125-150 DK COVERINGLOBBY(CENTRE) 1DZ0 6.8 DECKHEAD C212 36 36 NOTE 4 C061 30 30 WHITE 27925 PART INSULATIONLOBBY(CENTRE) 1DZ0 6.0 FORWARD C212 36 36 C061 30 30 GREY 27880LOBBY(CENTRE) 1DZ0 6.0 AFT C212 36 36 C061 30 30 GREY 27880LOBBY(CENTRE) 1DZ0 7.8 PORT C212 36 36 C061 30 30 GREY 27880LOBBY(CENTRE) 1DZ0 7.8 STBD C212 36 36 C061 30 30 GREY 27880LOBBY(CENTRE) 1DZ0 1.5 OTHERS C061 30 30 GREY 16076 DADO (150mm HIGH)LOBBY(FWD) 1DZ0 2.6 ST DECK C413 125-150 DK COVERINGLOBBY(FWD) 1DZ0 2.8 DECKHEAD C212 36 36 NOTE 4 C061 30 30 WHITE 27925 PART INSULATIONLOBBY(FWD) 1DZ0 6.0 FORWARD C212 36 36 C061 30 30 GREY 27880LOBBY(FWD) 1DZ0 6.0 AFT C212 36 36 C061 30 30 GREY 27880


Primer

DCZ Area M2

Surface1st Coat

µm


Name

Remarks

Rev: C


µm2nd Coat

µm


Finisher


µm3rd Coat

µm1st Coat

µm

LOBBY(FWD) 1DZ0 3.2 PORT C212 36 36 C061 30 30 GREY 27880LOBBY(FWD) 1DZ0 3.2 STBD C212 36 36 C061 30 30 GREY 27880CO'S/SO'S DAY/DINING ROOM 1DZ1 31.5 ST DECK C413 125-150 DK COVERINGCO'S/SO'S DAY/DINING ROOM 1DZ1 34.0 DECKHEAD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925CO'S/SO'S DAY/DINING ROOM 1DZ1 20.6 FORWARD C061 30 30 GREY 27886 JOINER BULKHEADCO'S/SO'S DAY/DINING ROOM 1DZ1 14.1 AFT C212 36 36 C061 30 30 GREY 27886 LININGCO'S/SO'S DAY/DINING ROOM 1DZ1 11.9 PORT C212 36 36 C061 30 30 GREY 27886 LININGCO'S/SO'S DAY/DINING ROOM 1DZ1 18.7 STBD C212 36 36 INSULATION C061 30 30 GREY 27886 LININGCO'S/SO'S DAY/DINING ROOM 1DZ1 21.0 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480

CBRN FILTER COMPARTMENT NO. 1 1DZ2 5.8 ST DECK TRAFFIC C413 125-150 C200 750-1000 GREY 36076

CBRN FILTER COMPARTMENT NO. 1 1DZ2 7.7 ST DECK NON TRAFFIC

C413 AND C045 C061 30 30 GREY 16076

CBRN FILTER COMPARTMENT NO. 1 1DZ2 14.6 DECKHEAD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925CBRN FILTER COMPARTMENT NO. 1 1DZ2 6.0 FORWARD C212 36 36 C061 30 30 WHITE 27925CBRN FILTER COMPARTMENT NO. 1 1DZ2 7.8 AFT C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925CBRN FILTER COMPARTMENT NO. 1 1DZ2 14.5 PORT C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925CBRN FILTER COMPARTMENT NO. 1 1DZ2 19.3 STBD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925CBRN FILTER COMPARTMENT NO. 1 1DZ2 7.2 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480CBRN FILTER COMPARTMENT NO. 1 1DZ2 15.5 OTHERS C061 30 30 GREY 16076 DADO (900mm HIGH)

H.F. TRANSMITTER ROOM 1EA0 11.8 ST DECK TRAFFIC C413 125-150 C200 750-1000 GREY 36076

H.F. TRANSMITTER ROOM 1EA0 7.3 ST DECK NON TRAFFIC

C413 AND C045 C061 OR C177 30 30 GREY 16076

H.F. TRANSMITTER ROOM 1EA0 20.6 DECKHEAD C212 36 36 NOTE 4 C061 30 30 WHITE 27925 PART INSULATIONH.F. TRANSMITTER ROOM 1EA0 12.5 FORWARD C212 36 36 C061 30 30 WHITE 27925H.F. TRANSMITTER ROOM 1EA0 12.9 AFT C212 36 36 C061 30 30 WHITE 27925H.F. TRANSMITTER ROOM 1EA0 11.0 PORT C212 36 36 C061 30 30 WHITE 27925H.F. TRANSMITTER ROOM 1EA0 12.9 STBD C212 36 36 C061 30 30 WHITE 27925CO'S/SO'S SERVERY 1EA1 6.5 ST DECK C413 125-150 DK COVERINGCO'S/SO'S SERVERY 1EA1 7.0 DECKHEAD C212 36 36 NOTE 4 C061 30 30 WHITE 27925 PART INSULATIONCO'S/SO'S SERVERY 1EA1 5.6 FORWARD C212 36 36 C061 30 30 WHITE 27925CO'S/SO'S SERVERY 1EA1 3.0 AFT C212 36 36 C061 30 30 WHITE 27925CO'S/SO'S SERVERY 1EA1 13.6 PORT C212 36 36 C061 30 30 WHITE 27925CO'S/SO'S SERVERY 1EA1 11.0 STBD C212 36 36 C061 30 30 WHITE 27925

DECK STORE NO. 2 1EA3 1.2 ST DECK TRAFFIC C413 125-150 C200 750-1000 GREY 36076

DECK STORE NO. 2 1EA3 2.6 ST DECK NON TRAFFIC

C413 AND C045 C061 OR C177 30 30 GREY 16076

DECK STORE NO. 2 1EA3 4.1 DECKHEAD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925DECK STORE NO. 2 1EA3 4.5 FORWARD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925DECK STORE NO. 2 1EA3 5.8 AFT C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925DECK STORE NO. 2 1EA3 8.2 PORT C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925DECK STORE NO. 2 1EA3 4.5 STBD C212 36 36 C061 30 30 WHITE 27925DECK STORE NO. 2 1EA3 5.4 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480DECK STORE NO. 2 1EA3 7.6 OTHERS C061 30 30 GREY 16076 DADO (900mm HIGH)

RAS FUELLING LOCKER 1EA5 1.2 ST DECK TRAFFIC C413 125-150 C200 750-1000 GREY 36076

RAS FUELLING LOCKER 1EA5 2.6 ST DECK NON TRAFFIC

C413 AND C045 C061 OR C177 30 30 GREY 16076


Primer

DCZ Area M2

Surface1st Coat

µm


Name

Remarks

Rev: C


µm2nd Coat

µm


Finisher


µm3rd Coat

µm1st Coat

µm

RAS FUELLING LOCKER 1EA5 1.8 DECKHEAD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925RAS FUELLING LOCKER 1EA5 5.6 FORWARD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925RAS FUELLING LOCKER 1EA5 7.2 AFT C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925RAS FUELLING LOCKER 1EA5 4.5 PORT C212 36 36 C061 30 30 WHITE 27925RAS FUELLING LOCKER 1EA5 6.7 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480RAS FUELLING LOCKER 1EA5 5.7 OTHERS C061 30 30 GREY 16076 DADO (900mm HIGH)

FAMR CASING(1 DECK TO CASING TOP ) 1EB0 13.2 ST DECK (11700 ABL) 76 C045 40 C076 30 30 GREY 26480

FAMR CASING(1 DECK TO CASING TOP ) 1EB0 8.1 ST DECK (01 DECK) 76 C045 40 C076 30 30 GREY 26480

FAMR CASING(1 DECK TO CASING TOP ) 1EB0 5.9 ST DECK (02 DECK) 76 C045 40 C076 30 30 GREY 26480

FAMR CASING(1 DECK TO CASING TOP ) 1EB0 14.9 FAMR CASING TOP 76 C045 40 C411 30 30 30 GREY 26480

FAMR CASING(1 DECK TO CASING TOP ) 1EB0 19.1DECKHEAD (UNDER 01


FAMR CASING(1 DECK TO CASING TOP ) 1EB0 6.4DECKHEAD (UNDER 02


FAMR CASING(1 DECK TO CASING TOP ) 1EB0 69.8 OUTSIDE OF FAMR CASING 76 C045 40 C411 30 30 30 GREY 26480

FAMR CASING(1 DECK TO CASING TOP ) 1EB0 56.5 FORWARD 76 INSULATION NOTE 5 GREY 26480FAMR CASING(1 DECK TO CASING TOP ) 1EB0 54.0 AFT 76 INSULATION NOTE 5 GREY 26480FAMR CASING(1 DECK TO CASING TOP ) 1EB0 27.1 PORT 76 INSULATION NOTE 5 GREY 26480FAMR CASING(1 DECK TO CASING TOP ) 1EB0 27.1 STBD 76 INSULATION NOTE 5 GREY 26480FAMR CASING (STBD PLENUM) 1EB1 3.3 ST DECK 76 C045 40 C076 30 30 GREY 26480FAMR CASING (STBD PLENUM) 1EB1 3.6 DECKHEAD 76 INSULATION NOTE 4 C076 30 30 GREY 26480FAMR CASING (STBD PLENUM) 1EB1 3.0 FORWARD 76 INSULATION NOTE 5 GREY 26480FAMR CASING (STBD PLENUM) 1EB1 3.0 AFT 76 INSULATION NOTE 5 GREY 26480FAMR CASING (STBD PLENUM) 1EB1 7.7 PORT 76 C076 30 30 GREY 26480FAMR CASING (STBD PLENUM) 1EB1 8.3 STBD 76 INSULATION NOTE 5 GREY 26480FAMR CASING (STBD PLENUM) 1EB1 7.7 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480FAMR CASING (PORT PLENUM) 1EB2 3.3 ST DECK 76 C045 40 C076 30 30 GREY 26480FAMR CASING (PORT PLENUM) 1EB2 3.6 DECKHEAD 76 INSULATION NOTE 4 C076 30 30 GREY 26480FAMR CASING (PORT PLENUM) 1EB2 3.0 FORWARD 76 INSULATION NOTE 5 GREY 26480FAMR CASING (PORT PLENUM) 1EB2 3.0 AFT 76 INSULATION NOTE 5 GREY 26480FAMR CASING (PORT PLENUM) 1EB2 8.3 PORT 76 INSULATION NOTE 5 GREY 26480FAMR CASING (PORT PLENUM) 1EB2 7.7 STBD 76 C076 30 30 GREY 26480FAMR CASING (PORT PLENUM) 1EB2 7.7 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480CBRND FILTER COMPT NO. 2/OUTBOARD MOTOR STORE & HYDRAULIC PUMP ROOM 1EZ 13.2 ST DECK

TRAFFIC C413 125-150 C200 750-1000 GREY 36076

CBRND FILTER COMPT NO. 2/OUTBOARD MOTOR STORE & HYDRAULIC PUMP ROOM 1EZ 6.6 ST DECK NON

TRAFFICC413 AND

C045 C061 30 30 GREY 16076

CBRND FILTER COMPT NO. 2/OUTBOARD MOTOR STORE & HYDRAULIC PUMP ROOM 1EZ 21.4 DECKHEAD C212 36 36 INSULATION NOTE 4 C212 30 30 WHITE 27925

CBRND FILTER COMPT NO. 2/OUTBOARD MOTOR STORE & HYDRAULIC PUMP ROOM 1EZ 18.1 FORWARD C212 36 36 C212 30 30 WHITE 27925

CBRND FILTER COMPT NO. 2/OUTBOARD MOTOR STORE & HYDRAULIC PUMP ROOM 1EZ 18.1 AFT C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925

CBRND FILTER COMPT NO. 2/OUTBOARD MOTOR STORE & HYDRAULIC PUMP ROOM 1EZ 8.3 PORT C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925


Primer

DCZ Area M2

Surface1st Coat

µm


Name

Remarks

Rev: C


µm2nd Coat

µm


Finisher


µm3rd Coat

µm1st Coat

µm

CBRND FILTER COMPT NO. 2/OUTBOARD MOTOR STORE & HYDRAULIC PUMP ROOM 1EZ 8.3 STBD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925

CBRND FILTER COMPT NO. 2/OUTBOARD MOTOR STORE & HYDRAULIC PUMP ROOM 1EZ 15.4 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480

CBRND FILTER COMPT NO. 2/OUTBOARD MOTOR STORE & HYDRAULIC PUMP ROOM 1EZ 17.3 OTHERS C061 30 30 GREY 16076 DADO (900mm HIGH)

FER INTAKES(1 DECK TO TOP OF INTAKES) 1FA 22.9 ST DECK (1 DECK)

C413 AND C045 125-150 C076 30 30 GREY 26480

FER INTAKES(1 DECK TO TOP OF INTAKES) 1FA 44.7 FER INTAKES TOP UNDERSIDE 76 C045 40 C076 30 30 GREY 26480

FER INTAKES(1 DECK TO TOP OF INTAKES) 1FA 31.5 FORWARD 76 C045 40 C076 30 30 GREY 26480FER INTAKES(1 DECK TO TOP OF INTAKES) 1FA 142.6 AFT 76 C045 40 C076 30 30 GREY 26480FER INTAKES(1 DECK TO TOP OF INTAKES) 1FA 29.4 PORT 76 C045 40 C076 30 30 GREY 26480FER INTAKES(1 DECK TO TOP OF INTAKES) 1FA 29.4 STBD 76 C045 40 C076 30 30 GREY 26480FER INTAKES(1 DECK TO TOP OF INTAKES) 1FA 58.8 CENTRELINE 76 C045 40 C076 30 30 GREY 26480

FER INTAKES(1 DECK TO TOP OF INTAKES) 1FA 152.7 OUTSIDE OF FER INTAKES 76 C045 40 C411 30 30 30 GREY 26480

SOLID WASTE HANDLING COMPARTMENT 1FZ0 9.8 ST DECK TRAFFIC 125-150 C200 750-1000 WHITE

SOLID WASTE HANDLING COMPARTMENT 1FZ0 13.3 ST DECK NON TRAFFIC C061 OR C177 30 30 WHITE

SOLID WASTE HANDLING COMPARTMENT 1FZ0 24.9 DECKHEAD 36 36 INSULATION NOTE 4 C061 30 30 WHITESOLID WASTE HANDLING COMPARTMENT 1FZ0 32.1 FORWARD 36 36 C061 30 30 WHITESOLID WASTE HANDLING COMPARTMENT 1FZ0 24.1 AFT 36 36 C061 30 30 WHITESOLID WASTE HANDLING COMPARTMENT 1FZ0 27.4 PORT 36 36 INSULATION NOTE 4 C061 30 30 WHITESOLID WASTE HANDLING COMPARTMENT 1FZ0 19.4 STBD 36 36 INSULATION NOTE 4 C061 30 30 WHITESOLID WASTE HANDLING COMPARTMENT 1FZ0 27.0 SHELL EXT 76 C411 30 30 30 WHITESOLID WASTE HANDLING COMPARTMENT 1FZ0 19.1 OTHERS C061 30 30 WHITE DADO (900mm HIGH)

AIR LOCK 1FZ2 13.2 ST DECK TRAFFIC C413 125-150 C200 750-1000 GREY 36076

AIR LOCK 1FZ2 6.6 ST DECK NON TRAFFIC

C413 AND C045 C061 OR C177 30 30 GREY 16076

AIR LOCK 1FZ2 3.6 DECKHEAD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925AIR LOCK 1FZ2 4.1 FORWARD C212 36 36 C061 30 30 WHITE 27925AIR LOCK 1FZ2 4.1 AFT C212 36 36 C061 30 30 WHITE 27925AIR LOCK 1FZ2 5.0 PORT C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925AIR LOCK 1FZ2 5.0 STBD C212 36 36 C061 30 30 WHITE 27925AIR LOCK 1FZ2 4.6 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480AIR LOCK 1FZ2 1.1 OTHERS C061 30 30 GREY 16076 DADO (150mm HIGH)

AER CASING(1 DECK TO FUNNEL TOP) 1GA 15.7 ST DECK (1 DECK)

C413 AND C045 C076 30 30 GREY 26480

AER CASING(1 DECK TO FUNNEL TOP) 1GA 30.8ST DECK

(FUNNEL HOUSE TOP)

76 C045 40 C076 30 30 BLACK 17038

AER CASING(1 DECK TO FUNNEL TOP) 1GA 12.5DECKHEAD

(FUNNEL HOUSE TOP)

76 INSULATION C076 30 30 GREY 26480

AER CASING(1 DECK TO FUNNEL TOP) 1GA 25.2 AER CASING TOP UNDERSIDE 76 INSULATION NOTE 4 C076 30 30 BLACK 17038

AER CASING(1 DECK TO FUNNEL TOP) 1GA 32.1FORWARD (1

DECK TO FUNNEL HOUSE

76 INSULATION NOTE 5 GREY 26480


Primer

DCZ Area M2

Surface1st Coat

µm


Name

Remarks

Rev: C


µm2nd Coat

µm


Finisher


µm3rd Coat

µm1st Coat

µm

AER CASING(1 DECK TO FUNNEL TOP) 1GA 33.5AFT(1 DECK TO FUNNEL HOUSE

TOP)76 INSULATION NOTE 5 GREY 26480

AER CASING(1 DECK TO FUNNEL TOP) 1GA 17.9PORT (1 DECK

TO FUNNEL HOUSE TOP)


AER CASING(1 DECK TO FUNNEL TOP) 1GA 17.9STBD (1 DECK

TO FUNNEL HOUSE TOP)


AER CASING(1 DECK TO FUNNEL TOP) 1GA 47.4

FORWARD (FUNNEL HOUSE TOP TO FUNNEL

TOP)

76 C045 40 C076 30 30 BLACK 17038

AER CASING(1 DECK TO FUNNEL TOP) 1GA 47.3AFT (FUNNEL

HOUSE TOP TO FUNNEL TOP)

76 INSULATION NOTE 5 BLACK 17038

AER CASING(1 DECK TO FUNNEL TOP) 1GA 33.4PORT (FUNNEL HOUSE TOP TO FUNNEL TOP)


AER CASING(1 DECK TO FUNNEL TOP) 1GA 33.4STBD(FUNNEL HOUSE TOP TO FUNNEL TOP)


AER CASING(1 DECK TO FUNNEL TOP) 1GA 23.3 AER FUNNEL TOP 76 C045 40 C076 30 30 30 BLACK 17038

AER CASING(1 DECK TO FUNNEL TOP) 1GA 176.6 AER CASING EXTERIOR 76 C045 40 C411 30 30 30 GREY 26480

CBRN FILTER COMPT NO. 3 1GZ1 3.0 ST DECK TRAFFIC C413 125-150 C200 750-1000 GREY 36076

CBRN FILTER COMPT NO. 3 1GZ1 5.0 ST DECK NON TRAFFIC

C413 AND C045 C061 OR C177 30 30 GREY 16076

CBRN FILTER COMPT NO. 3 1GZ1 8.6 DECKHEAD C212 36 36 NOTE 4 C061 30 30 WHITE 27925 PART INSULATIONCBRN FILTER COMPT NO. 3 1GZ1 7.2 FORWARD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925CBRN FILTER COMPT NO. 3 1GZ1 11.3 AFT C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925CBRN FILTER COMPT NO. 3 1GZ1 9.1 PORT C212 36 36 C061 30 30 WHITE 27925CBRN FILTER COMPT NO. 3 1GZ1 9.9 STBD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925CBRN FILTER COMPT NO. 3 1GZ1 10.4 OTHERS C061 30 30 GREY 16076 DADO (900mm HIGH)

TORPEDO MAGAZINE NO. 1 1HA1 17.1 ST DECK TRAFFIC C413 125-150 C200 750-1000 GREY 36076

TORPEDO MAGAZINE NO. 1 1HA1 13.1 ST DECK NON TRAFFIC

C413 AND C045 C061 OR C177 30 30 GREY 16076

TORPEDO MAGAZINE NO. 1 1HA1 35.6 DECKHEAD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925TORPEDO MAGAZINE NO. 1 1HA1 20.5 FORWARD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925TORPEDO MAGAZINE NO. 1 1HA1 13.0 AFT C212 36 36 C061 30 30 WHITE 27925TORPEDO MAGAZINE NO. 1 1HA1 22.8 PORT C212 36 36 C061 30 30 WHITE 27925TORPEDO MAGAZINE NO. 1 1HA1 30.6 STBD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925TORPEDO MAGAZINE NO. 1 1HA1 4.0 OTHERS C061 30 30 GREY 16076 DADO (150mm HIGH)TORPEDO MAGAZINE NO. 1 1HA1 7.1 OTHERS C212 36 36 C061 30 30 WHITE 27925 UNDER TORPEDO STOWAGE

TORPEDO MAGAZINE NO. 2 1HA2 17.1 ST DECK TRAFFIC C413 64 C200 750-1000 GREY 36076

TORPEDO MAGAZINE NO. 2 1HA2 13.1 ST DECK NON TRAFFIC

C413 AND C045 C061 OR C177 30 30 GREY 16076

TORPEDO MAGAZINE NO. 2 1HA2 35.6 DECKHEAD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925TORPEDO MAGAZINE NO. 2 1HA2 20.5 FORWARD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925


Primer

DCZ Area M2

Surface1st Coat

µm


Name

Remarks

Rev: C


µm2nd Coat

µm


Finisher


µm3rd Coat

µm1st Coat

µm

TORPEDO MAGAZINE NO. 2 1HA2 13.0 AFT C212 36 36 C061 30 30 WHITE 27925TORPEDO MAGAZINE NO. 2 1HA2 30.6 PORT C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925TORPEDO MAGAZINE NO. 2 1HA2 22.8 STBD C212 36 36 C061 30 30 WHITE 27925TORPEDO MAGAZINE NO. 2 1HA2 4.0 OTHERS C061 30 30 GREY 16076 DADO (150mm HIGH)TORPEDO MAGAZINE NO. 2 1HA2 7.1 OTHERS C212 36 36 C061 30 30 WHITE 27925 UNDER TORPEDO STOWAGEHANGAR(1 DECK TO 01 DECK) 1JA0 137.3 ST DECK C413 125-150 C200 750-1000 GREY 36076HANGAR(1 DECK TO 01 DECK) 1JA0 26.1 FORWARD C212 36 36 C061 30 30 WHITE 27925HANGAR(1 DECK TO 01 DECK) 1JA0 26.1 AFT C212 36 36 C061 30 30 WHITE 27925HANGAR(1 DECK TO 01 DECK) 1JA0 55.1 PORT C212 36 36 C061 30 30 WHITE 27925HANGAR(1 DECK TO 01 DECK) 1JA0 55.1 STBD C212 36 36 C061 30 30 WHITE 27925HANGAR(1 DECK TO 01 DECK) 1JA0 45.1 OTHERS C061 30 30 GREY 16076 DADO (900mm HIGH)

LOBBY(PORT-FWD) 1JA0 4.2 ST DECK TRAFFIC C413 125-150 C200 750-1000 GREY 36076

LOBBY(PORT-FWD) 1JA0 1.7 ST DECK NON TRAFFIC

C413 AND C045 C061 OR C177 30 30 GREY 16076

LOBBY(PORT-FWD) 1JA0 6.4 DECKHEAD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925LOBBY(PORT-FWD) 1JA0 8.3 FORWARD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925LOBBY(PORT-FWD) 1JA0 14.1 AFT C212 36 36 C061 30 30 WHITE 27925LOBBY(PORT-FWD) 1JA0 1.6 PORT C212 36 36 C061 30 30 WHITE 27925LOBBY(PORT-FWD) 1JA0 12.9 STBD C212 36 36 C061 30 30 WHITE 27925LOBBY(PORT-FWD) 1JA0 1.7 OTHERS C061 30 30 GREY 16076 DADO (150mm HIGH)

LOBBY(STBD-FWD) 1JA0 4.2 ST DECK TRAFFIC C413 125-150 C200 750-1000 GREY 36076

LOBBY(STBD-FWD) 1JA0 1.7 ST DECK NON TRAFFIC

C413 AND C045 C061 OR C177 30 30 GREY 16076

LOBBY(STBD-FWD) 1JA0 6.4 DECKHEAD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925LOBBY(STBD-FWD) 1JA0 8.3 FORWARD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925LOBBY(STBD-FWD) 1JA0 14.1 AFT C212 36 36 C061 30 30 WHITE 27925LOBBY(STBD-FWD) 1JA0 12.9 PORT C212 36 36 C061 30 30 WHITE 27925LOBBY(STBD-FWD) 1JA0 1.6 STBD C212 36 36 C061 30 30 WHITE 27925LOBBY(STBD-FWD) 1JA0 1.7 OTHERS C061 30 30 GREY 16076 DADO (150mm HIGH)HELO TAIL PROBE MARK 1JA0 0.01 DECKHEAD C061 30 30 WHITE 37925HANGAR(01 DECK TO HANGAR TOP) 1JA0 120.4 DECKHEAD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925HANGAR(01 DECK TO HANGAR TOP) 1JA0 27.5 FORWARD C212 36 36 C061 30 30 WHITE 27925HANGAR(01 DECK TO HANGAR TOP) 1JA0 32.6 AFT C212 36 36 NOTE 4 C061 30 30 WHITE 27925 PART INSULATIONHANGAR(01 DECK TO HANGAR TOP) 1JA0 71.7 PORT C212 36 36 NOTE 4 C061 30 30 WHITE 27925 PART INSULATIONHANGAR(01 DECK TO HANGAR TOP) 1JA0 71.7 STBD C212 36 36 NOTE 4 C061 30 30 WHITE 27925 PART INSULATIONHANGAR(01 DECK TO HANGAR TOP) 1JA0 206.3 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480

LOBBY(STBD-AFT) 1JA1 8.2 ST DECK TRAFFIC C413 125-150 C200 750-1000 GREY 36076

LOBBY(STBD-AFT) 1JA1 2.2 ST DECK NON TRAFFIC

C413 AND C045 C061 OR C177 30 30 GREY 16076

LOBBY(STBD-AFT) 1JA1 11.4 DECKHEAD C212 36 36 NOTE 4 C061 30 30 WHITE 27925 PART INSULATIONLOBBY(STBD-AFT) 1JA1 6.6 FORWARD C212 36 36 C061 30 30 WHITE 27925LOBBY(STBD-AFT) 1JA1 5.6 AFT C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925LOBBY(STBD-AFT) 1JA1 19.4 PORT C212 36 36 C061 30 30 WHITE 27925LOBBY(STBD-AFT) 1JA1 20.4 STBD C212 36 36 C061 30 30 WHITE 27925LOBBY(STBD-AFT) 1JA1 2.4 OTHERS C061 30 30 GREY 16076 DADO (150mm HIGH)

LOBBY(PORT-AFT) 1JA2 12.8 ST DECK TRAFFIC C413 125-150 C200 750-1000 GREY 36076


Primer

DCZ Area M2

Surface1st Coat

µm


Name

Remarks

Rev: C


µm2nd Coat

µm


Finisher


µm3rd Coat

µm1st Coat

µm

LOBBY(PORT-AFT) 1JA2 8.2 ST DECK NON TRAFFIC

C413 AND C045 C061 OR C177 30 30 GREY 16076

LOBBY(PORT-AFT) 1JA2 20.2 DECKHEAD C212 36 36 NOTE 4 C061 30 30 WHITE 27925 PART INSULATIONLOBBY(PORT-AFT) 1JA2 13.0 FORWARD C212 36 36 C061 30 30 WHITE 27925LOBBY(PORT-AFT) 1JA2 15.9 AFT C212 36 36 NOTE 4 C061 30 30 WHITE 27925 PART INSULATIONLOBBY(PORT-AFT) 1JA2 16.4 PORT C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925LOBBY(PORT-AFT) 1JA2 19.4 STBD C212 36 36 C061 30 30 WHITE 27925LOBBY(PORT-AFT) 1JA2 3.0 OTHERS C061 30 30 GREY 16076 DADO (150mm HIGH)

SONOBUOY STORE NO. 2 1JA3 2.6 ST DECK TRAFFIC C413 125-150 C200 750-1000 GREY 36076

SONOBUOY STORE NO. 2 1JA3 5.9 ST DECK NON TRAFFIC

C413 AND C045 C061 OR C177 30 30 GREY 16076

SONOBUOY STORE NO. 2 1JA3 7.2 DECKHEAD C212 36 36 NOTE 4 C061 30 30 WHITE 27925 PART INSULATIONSONOBUOY STORE NO. 2 1JA3 6.5 FORWARD C212 36 36 C061 30 30 WHITE 27925SONOBUOY STORE NO. 2 1JA3 7.1 AFT C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925SONOBUOY STORE NO. 2 1JA3 14.0 PORT C212 36 36 C061 30 30 WHITE 27925SONOBUOY STORE NO. 2 1JA3 13.2 STBD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925SONOBUOY STORE NO. 2 1JA3 1.9 OTHERS C061 30 30 GREY 16076 DADO (150mm HIGH)

HELO READY USE LUB LOCKER 1JZ1 1.6 ST DECK TRAFFIC C413 125-150 C200 750-1000 GREY 36076

HELO READY USE LUB LOCKER 1JZ1 2.7 ST DECK NON TRAFFIC

C413 AND C045 C061 OR C177 30 30 GREY 16076

HELO READY USE LUB LOCKER 1JZ1 3.5 DECKHEAD C212 36 36 NOTE 4 C061 30 30 WHITE 27925 PART INSULATIONHELO READY USE LUB LOCKER 1JZ1 7.1 FORWARD C212 36 36 C061 30 30 WHITE 27925HELO READY USE LUB LOCKER 1JZ1 6.9 AFT C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925HELO READY USE LUB LOCKER 1JZ1 6.5 PORT C212 36 36 C061 30 30 WHITE 27925HELO READY USE LUB LOCKER 1JZ1 6.5 STBD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925

Q.M'S LOBBY 1JZ2 2.7 ST DECK TRAFFIC C413 125-150 C200 750-1000 GREY 36076

Q.M'S LOBBY 1JZ2 2.1 ST DECK NON TRAFFIC

C413 AND C045 C061 OR C177 30 30 GREY 16076

Q.M'S LOBBY 1JZ2 3.9 DECKHEAD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925Q.M'S LOBBY 1JZ2 8.4 FORWARD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925Q.M'S LOBBY 1JZ2 5.9 AFT C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925Q.M'S LOBBY 1JZ2 6.5 PORT C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925Q.M'S LOBBY 1JZ2 7.2 STBD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925Q.M'S LOBBY 1JZ2 1.3 OTHERS C061 30 30 GREY 16076 DADO (150mm HIGH)

PLENUM(1 DECK, AFT FR 59) 1MA0 0.7 ST DECK TRAFFIC C413 125-150 C200 750-1000 GREY 36076

PLENUM(1 DECK, AFT FR 59) 1MA0 0.4 ST DECK NON TRAFFIC

C413 AND C045 C061 OR C177 30 30 GREY 16076

PLENUM(1 DECK, AFT FR 59) 1MA0 1.2 DECKHEAD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925PLENUM(1 DECK, AFT FR 59) 1MA0 0.6 FORWARD C212 36 36 C061 30 30 WHITE 27925PLENUM(1 DECK, AFT FR 59) 1MA0 0.6 AFT C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925PLENUM(1 DECK, AFT FR 59) 1MA0 1.3 PORT C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925PLENUM(1 DECK, AFT FR 59) 1MA0 1.3 STBD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925PLENUM(1 DECK, AFT FR 59) 1MA0 0.7 OTHERS C061 30 30 GREY 16076 DADO (150mm HIGH)

PLENUM(1 DECK, AFT FR 59) 1MA2 0.8 ST DECK C413 AND C045 C061 30 30 GREY 16076



Primer

DCZ Area M2

Surface1st Coat

µm


Name

Remarks

Rev: C


µm2nd Coat

µm


Finisher


µm3rd Coat

µm1st Coat

µm

PLENUM(1 DECK, AFT FR 59) 1MA4 0.9 ST DECK C413 AND C045 C061 30 30 GREY 16076


PLENUM(1 DECK, AFT FR 59) 1MZ0 1.6 ST DECK TRAFFIC C413 125-150 C200 750-1000 GREY 36076

PLENUM(1 DECK, AFT FR 59) 1MZ0 0.8 ST DECK NON TRAFFIC

C413 AND C045 C061 OR C177 30 30 GREY 16076

PLENUM(1 DECK, AFT FR 59) 1MZ0 2.6 DECKHEAD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925PLENUM(1 DECK, AFT FR 59) 1MZ0 3.1 FORWARD C212 36 36 C061 30 30 WHITE 27925PLENUM(1 DECK, AFT FR 59) 1MZ0 2.3 AFT C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925PLENUM(1 DECK, AFT FR 59) 1MZ0 0.8 PORT C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925PLENUM(1 DECK, AFT FR 59) 1MZ0 1.4 STBD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925PLENUM(1 DECK, AFT FR 59) 1MZ0 1.3 OTHERS C061 30 30 GREY 16076 DADO (150mm HIGH)

PLENUM(1 DECK, AFT FR 59) 1MZ2 1.1 ST DECK TRAFFIC C413 125-150 C200 750-1000 GREY 36076

PLENUM(1 DECK, AFT FR 59) 1MZ2 0.6 ST DECK NON TRAFFIC

C413 AND C045 C061 OR C177 30 30 GREY 16076

PLENUM(1 DECK, AFT FR 59) 1MZ2 1.8 DECKHEAD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925PLENUM(1 DECK, AFT FR 59) 1MZ2 0.6 FORWARD C212 36 36 C061 30 30 WHITE 27925PLENUM(1 DECK, AFT FR 59) 1MZ2 0.6 AFT C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925PLENUM(1 DECK, AFT FR 59) 1MZ2 2.1 PORT C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925PLENUM(1 DECK, AFT FR 59) 1MZ2 2.1 STBD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925PLENUM(1 DECK, AFT FR 59) 1MZ2 0.9 OTHERS C061 30 30 GREY 16076 DADO (150mm HIGH)BRIDGE 01DA 66.5 ST DECK C413 125-150 NOTE 15 BELOW FALSE DECKBRIDGE 01DA 71.8 DECKHEAD C212 36 36 INSULATION NOTE 5 WHITE 27925BRIDGE 01DA 19.5 FORWARD C212 36 36 INSULATION NOTE 5 GREEN 24670BRIDGE 01DA 35.4 AFT C212 36 36 INSULATION NOTE 5 GREEN 24670BRIDGE 01DA 31.4 PORT C212 36 36 INSULATION NOTE 5 GREEN 24670BRIDGE 01DA 31.5 STBD C212 36 36 INSULATION NOTE 5 GREEN 24670BRIDGE 01DA 76.4 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480CHART ROOM 01DB0 12.1 ST DECK C413 125-150 DK COVERINGCHART ROOM 01DB0 13.1 DECKHEAD C212 36 36 INSULATION NOTE 5 WHITE 27925CHART ROOM 01DB0 11.2 FORWARD C212 36 36 C061 30 30 GREEN 24670CHART ROOM 01DB0 11.2 AFT C212 36 36 C061 30 30 GREEN 24670CHART ROOM 01DB0 8.5 PORT C212 36 36 C061 30 30 GREEN 24670CHART ROOM 01DB0 8.5 STBD C212 36 36 C061 30 30 GREEN 24670

FIRE CONTROL EQUIPMENT ROOM NO. 1 01DC0 11.8 ST DECK TRAFFIC C413 125-150 C200 750-1000 GREY 36076

FIRE CONTROL EQUIPMENT ROOM NO. 1 01DC0 8.9 ST DECK NON TRAFFIC

C413 AND C045 C061 OR C177 30 30 GREY 16076

FIRE CONTROL EQUIPMENT ROOM NO. 1 01DC0 22.4 DECKHEAD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925FIRE CONTROL EQUIPMENT ROOM NO. 1 01DC0 14.0 FORWARD C212 36 36 C061 30 30 WHITE 27925FIRE CONTROL EQUIPMENT ROOM NO. 1 01DC0 14.0 AFT C212 36 36 C061 30 30 WHITE 27925FIRE CONTROL EQUIPMENT ROOM NO. 1 01DC0 12.2 PORT C061 30 30 WHITE 27925 JOINER BULKHEADFIRE CONTROL EQUIPMENT ROOM NO. 1 01DC0 11.2 STBD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925FIRE CONTROL EQUIPMENT ROOM NO. 1 01DC0 10.4 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480


Primer

DCZ Area M2

Surface1st Coat

µm


Name

Remarks

Rev: C


µm2nd Coat

µm


Finisher


µm3rd Coat

µm1st Coat

µm

COMMUNICATION LOCKER 01DY1 0.7 ST DECK TRAFFIC C413 125-150 C200 750-1000 GREY 36076

COMMUNICATION LOCKER 01DY1 0.2 ST DECK NON TRAFFIC

C413 AND C045 C061 OR C177 30 30 GREY 16076

COMMUNICATION LOCKER 01DY1 0.9 DECKHEAD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925COMMUNICATION LOCKER 01DY1 2.2 FORWARD C061 30 30 WHITE 27925 JOINER BULKHEADCOMMUNICATION LOCKER 01DY1 2.4 AFT C212 36 36 C061 30 30 WHITE 27925COMMUNICATION LOCKER 01DY1 2.4 PORT C061 30 30 WHITE 27925 JOINER BULKHEADCOMMUNICATION LOCKER 01DY1 2.6 STBD C212 36 36 C061 30 30 WHITE 27925SEA HEAD 01DY3 1.8 ST DECK C413 125-150 DK COVERINGSEA HEAD 01DY3 1.9 DECKHEAD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925SEA HEAD 01DY3 5.2 FORWARD C061 30 30 GREY 27880 JOINER BULKHEADSEA HEAD 01DY3 5.6 AFT C212 36 36 C061 30 30 GREY 27880SEA HEAD 01DY3 2.3 PORT C212 36 36 C061 30 30 GREY 27880

SEA HEAD 01DY3 2.5 STBD C212 36 36 INSULATION NOTE 4 C061 30 30 GREY 27880


SEA HEAD 01DY3 2.3 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480

RADAR ROOM NO. 1 01DZ0 10.0 ST DECK TRAFFIC C413 125-150 C200 750-1000 GREY 36076

RADAR ROOM NO. 1 01DZ0 5.4 ST DECK NON TRAFFIC

C413 AND C045 C061 OR C177 30 30 GREY 16076

RADAR ROOM NO. 1 01DZ0 16.6 DECKHEAD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925RADAR ROOM NO. 1 01DZ0 15.0 FORWARD C212 36 36 C061 30 30 WHITE 27925RADAR ROOM NO. 1 01DZ0 14.0 AFT C212 36 36 C061 30 30 WHITE 27925RADAR ROOM NO. 1 01DZ0 8.7 PORT C061 30 30 WHITE 27925 JOINER BULKHEADRADAR ROOM NO. 1 01DZ0 8.4 STBD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925RADAR ROOM NO. 1 01DZ0 7.8 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480LOBBY(FWD OF FR 16) 01DZ2 1.5 ST DECK C413 125-150 DK COVERINGLOBBY(FWD OF FR 16) 01DZ2 1.6 DECKHEAD C212 36 36 INSULATION NOTE 5 WHITE 27925LOBBY(FWD OF FR 16) 01DZ2 3.6 FORWARD C212 36 36 C061 30 30 GREY 27880LOBBY(FWD OF FR 16) 01DZ2 3.6 AFT C212 36 36 C061 30 30 GREY 27880LOBBY(FWD OF FR 16) 01DZ2 3.2 PORT C212 36 36 C061 30 30 GREY 27880LOBBY(FWD OF FR 16) 01DZ2 3.2 STBD C212 36 36 C061 30 30 GREY 27880LOBBY(FWD OF FR 16) 01DZ2 0.7 OTHERS C061 30 30 GREY 16076 DADO(150mm HIGH)LOBBY(FR 20.5 T0 FR 19) 01DZ2 4.5 ST DECK C413 125-150 DK COVERINGLOBBY(FR 20.5 T0 FR 19) 01DZ2 4.9 DECKHEAD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925LOBBY(FR 20.5 T0 FR 19) 01DZ2 3.6 FORWARD C212 36 36 INSULATION NOTE 4 C061 30 30 GREY 27880LOBBY(FR 20.5 T0 FR 19) 01DZ2 4.5 AFT C212 36 36 INSULATION NOTE 4 C061 30 30 GREY 27880LOBBY(FR 20.5 T0 FR 19) 01DZ2 8.5 PORT C212 36 36 INSULATION NOTE 4 C061 30 30 GREY 27880LOBBY(FR 20.5 T0 FR 19) 01DZ2 8.7 STBD C061 30 30 GREY 27880 JOINER BULKHEADLOBBY(FR 20.5 T0 FR 19) 01DZ2 7.9 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480LOBBY(FR 20.5 T0 FR 19) 01DZ2 1.4 OTHERS C061 30 30 GREY 16076 DADO(150mm HIGH)LOBBY(FR 19 TO FR 18) 01DZ2 9.6 ST DECK C413 125-150 DK COVERINGLOBBY(FR 19 TO FR 18) 01DZ2 11.4 DECKHEAD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925LOBBY(FR 19 TO FR 18) 01DZ2 18.6 FORWARD C212 36 36 C061 30 30 GREY 27880LOBBY(FR 19 TO FR 18) 01DZ2 21.2 AFT C212 36 36 C061 30 30 GREY 27880 CLEAR OF JOINER BULKHEAD


Primer

DCZ Area M2

Surface1st Coat

µm


Name

Remarks

Rev: C


µm2nd Coat

µm


Finisher


µm3rd Coat

µm1st Coat

µm

LOBBY(FR 19 TO FR 18) 01DZ2 5.5 PORT C212 36 36 INSULATION NOTE 4 C061 30 30 GREY 27880LOBBY(FR 19 TO FR 18) 01DZ2 3.0 STBD C212 36 36 INSULATION NOTE 4 C061 30 30 GREY 27880LOBBY(FR 19 TO FR 18) 01DZ2 7.9 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480LOBBY(FR 19 TO FR 18) 01DZ2 2.6 OTHERS C061 30 30 GREY 16076 DADO(150mm HIGH)LOBBY(FR 18 TO FR 16) 01DZ2 5.9 ST DECK C413 125-150 DK COVERINGLOBBY(FR 18 TO FR 16) 01DZ2 6.4 DECKHEAD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925LOBBY(FR 18 TO FR 16) 01DZ2 4.5 FORWARD C212 36 36 C061 30 30 GREY 27880LOBBY(FR 18 TO FR 16) 01DZ2 4.5 AFT C212 36 36 C061 30 30 GREY 27880LOBBY(FR 18 TO FR 16) 01DZ2 11.2 PORT C212 36 36 INSULATION NOTE 4 C061 30 30 GREY 27880LOBBY(FR 18 TO FR 16) 01DZ2 12.2 STBD C061 30 30 GREY 27880 JOINER BULKHEADLOBBY(FR 18 TO FR 16) 01DZ2 10.4 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480LOBBY(FR 18 TO FR 16) 01DZ2 1.8 OTHERS C061 30 30 GREY 16076 DADO(150mm HIGH)

ELECTRONIC WARFARE EQUIPMENT ROOM 01EA 10.2 ST DECK TRAFFIC C413 125-150 C200 750-1000 GREY 36076

ELECTRONIC WARFARE EQUIPMENT ROOM 01EA 5.8 ST DECK NON TRAFFIC

C413 AND C045 C061 OR C177 30 30 GREY 16076

ELECTRONIC WARFARE EQUIPMENT ROOM 01EA 17.3 DECKHEAD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925ELECTRONIC WARFARE EQUIPMENT ROOM 01EA 18.6 FORWARD C212 36 36 C061 30 30 WHITE 27925ELECTRONIC WARFARE EQUIPMENT ROOM 01EA 18.6 AFT C212 36 36 C061 30 30 WHITE 27925ELECTRONIC WARFARE EQUIPMENT ROOM 01EA 6.8 PORT C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925ELECTRONIC WARFARE EQUIPMENT ROOM 01EA 6.8 STBD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925ELECTRONIC WARFARE EQUIPMENT ROOM 01EA 12.6 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480CHAFF MAGAZINE 01EB 10.5 ST DECK C413 125-150 DK COVERINGCHAFF MAGAZINE 01EB 11.3 DECKHEAD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925CHAFF MAGAZINE 01EB 18.6 FORWARD C212 36 36 C061 30 30 WHITE 27925CHAFF MAGAZINE 01EB 18.6 AFT C212 36 36 C061 30 30 WHITE 27925CHAFF MAGAZINE 01EB 4.4 PORT C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925CHAFF MAGAZINE 01EB 4.4 STBD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925CHAFF MAGAZINE 01EB 4.1 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480STBD FER UPTAKES(13200 G.T. FLAT TO 19600 G.T. FLAT) 01FZ1 15.8 ST DECK (13200

G.T. FLAT) 76 C045 40 C076 30 30 BLACK 17038

STBD FER UPTAKES(13200 G.T. FLAT TO 19600 G.T. FLAT) 01FZ1 3.7

ST DECK (FUNNEL HOUSE

TOP)76 C045 40 C076 30 30 BLACK 17038


DECKHEAD (FUNNEL HOUSE

TOP)76 INSULATION C076 30 30 GREY 26480


DECKHEAD (19600 G.T.

FLAT)76 INSULATION NOTE 4 C076 30 30 BLACK 17038

STBD FER UPTAKES(13200 G.T. FLAT TO 19600 G.T. FLAT) 01FZ1 23.9 FORWARD 76 INSULATION NOTE 5 GREY 26480

STBD FER UPTAKES(13200 G.T. FLAT TO 19600 G.T. FLAT) 01FZ1 98.9 AFT (INCLUDES

PLENUM) 76 C045 40 C076 30 30 BLACK 17038

STBD FER UPTAKES(13200 G.T. FLAT TO 19600 G.T. FLAT) 01FZ1 40.5 PORT 76 INSULATION NOTE 5 GREY 26480

STBD FER UPTAKES(13200 G.T. FLAT TO 19600 G.T. FLAT) 01FZ1 40.5 STBD 76 INSULATION NOTE 5 GREY 26480

STBD FER UPTAKES(13200 G.T. FLAT TO 19600 G.T. FLAT) 01FZ1 59.3 OUTSIDE OF

FER UPTAKES 76 C045 40 C061 30 30 30 GREY 26480

PORT FER UPTAKES(13200 G.T. FLAT TO 19600 G.T. FLAT) 01FZ2 15.8 ST DECK (13200

G.T. FLAT) 76 C045 40 C076 30 30 BLACK 17038


Primer

DCZ Area M2

Surface1st Coat

µm


Name

Remarks

Rev: C


µm2nd Coat

µm


Finisher


µm3rd Coat

µm1st Coat

µm

PORT FER UPTAKES(13200 G.T. FLAT TO 19600 G.T. FLAT) 01FZ2 3.7

ST DECK (FUNNEL HOUSE

TOP)76 C045 40 C076 30 30 BLACK 17038


DECKHEAD (FUNNEL HOUSE

TOP)76 INSULATION C076 30 30 GREY 26480


DECKHEAD (19600 G.T.

FLAT)76 INSULATION NOTE 4 C076 30 30 BLACK 17038

PORT FER UPTAKES(13200 G.T. FLAT TO 19600 G.T. FLAT) 01FZ2 23.9 FORWARD 76 INSULATION NOTE 5 GREY 26480

PORT FER UPTAKES(13200 G.T. FLAT TO 19600 G.T. FLAT) 01FZ2 98.9 AFT(INCLUDES

PLENUM) 76 C045 40 C076 30 30 BLACK 17038

PORT FER UPTAKES(13200 G.T. FLAT TO 19600 G.T. FLAT) 01FZ2 40.5 PORT 76 INSULATION NOTE 5 GREY 26480

PORT FER UPTAKES(13200 G.T. FLAT TO 19600 G.T. FLAT) 01FZ2 40.5 STBD 76 INSULATION NOTE 5 GREY 26480

PORT FER UPTAKES(13200 G.T. FLAT TO 19600 G.T. FLAT) 01FZ2 59.3 OUTSIDE OF


AAMR CASING(01 DECK TO AAMR CASING TOP) 01GZ0 12.4 ST DECK (01 DECK) 76 C045 40 C076 30 30 GREY 26480

AAMR CASING(01 DECK TO AAMR CASING TOP) 01GZ0 8.0 ST DECK (HANGAR TOP) 76 C045 40 C076 30 30 GREY 26480

AAMR CASING(01 DECK TO AAMR CASING TOP) 01GZ0 8.6 DECKHEAD (HANGAR TOP) 76 INSULATION NOTE 4 C076 30 30 GREY 26480

AAMR CASING(01 DECK TO AAMR CASING TOP) 01GZ0 4.6 AAMR CASING TOP UNDERSIDE 76 INSULATION NOTE 4 C076 30 30 GREY 26480

AAMR CASING(01 DECK TO AAMR CASING TOP) 01GZ0 21.3 FORWARD 76 INSULATION NOTE 5 GREY 26480

AAMR CASING(01 DECK TO AAMR CASING TOP) 01GZ0 26.4 AFT 76 INSULATION NOTE 5 GREY 26480

AAMR CASING(01 DECK TO AAMR CASING TOP) 01GZ0 17.6 PORT 76 INSULATION NOTE 5 GREY 26480

AAMR CASING(01 DECK TO AAMR CASING TOP) 01GZ0 16.6 STBD 76 INSULATION NOTE 5 GREY 26480

AAMR CASING(01 DECK TO AAMR CASING TOP) 01GZ0 4.3 AAMR CASING TOP 76 C045 40 C411 30 30 30 GREY 26480

AAMR CASING(01 DECK TO AAMR CASING TOP) 01GZ0 46.5 AAMR CASING EXTERIOR 76 C045 40 C411 30 30 30 GREY 26480

ENGINEER'S STORE 01GZ1 2.8 ST DECK TRAFFIC C413 125-150 C200 750-1000 GREY 36076

ENGINEER'S STORE 01GZ1 3.6 ST DECK NON TRAFFIC

C413 AND C045 C061 OR C177 30 30 GREY 16076

ENGINEER'S STORE 01GZ1 3.1 DECKHEAD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925ENGINEER'S STORE 01GZ1 4.2 FORWARDENGINEER'S STORE 01GZ1 9.3 AFT C212 36 36 C061 30 30 WHITE 27925ENGINEER'S STORE 01GZ1 11.4 PORT C212 36 36 C061 30 30 WHITE 27925ENGINEER'S STORE 01GZ1 13.2 STBD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925ENGINEER'S STORE 01GZ1 18.9 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480ENGINEER'S STORE 01GZ1 9.4 OTHERS C061 30 30 GREY 16076 DADO (900mm HIGH)

CIWS MAGAZINE 01JA1 6.1 ST DECK TRAFFIC C413 125-150 C200 750-1000 GREY 36076

CIWS MAGAZINE 01JA1 5.8 ST DECK NON TRAFFIC

C413 AND C045 C061 OR C177 30 30 GREY 16076


Primer

DCZ Area M2

Surface1st Coat

µm


Name

Remarks

Rev: C


µm2nd Coat

µm


Finisher


µm3rd Coat

µm1st Coat

µm

CIWS MAGAZINE 01JA1 9.7 DECKHEAD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925CIWS MAGAZINE 01JA1 12.6 FORWARD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925CIWS MAGAZINE 01JA1 8.3 AFT C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925CIWS MAGAZINE 01JA1 25.8 PORT C212 36 36 C061 30 30 WHITE 27925CIWS MAGAZINE 01JA1 15.6 STBD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925CIWS MAGAZINE 01JA1 22.6 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480CIWS MAGAZINE 01JA1 2.5 OTHERS C061 30 30 GREY 16076 DADO (150mm HIGH)

SONOBUOY STORE NO. 1 01JA2 5.2 ST DECK TRAFFIC C413 125-150 C200 750-1000 GREY 36076

SONOBUOY STORE NO. 1 01JA2 4.6 ST DECK NON TRAFFIC

C413 AND C045 C061 OR C177 30 30 GREY 16076

SONOBUOY STORE NO. 1 01JA2 7.7 DECKHEAD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925SONOBUOY STORE NO. 1 01JA2 12.7 FORWARD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925SONOBUOY STORE NO. 1 01JA2 7.8 AFT C061 30 30 WHITE 27925 JOINER BULKHEADSONOBUOY STORE NO. 1 01JA2 13.7 PORT C061 30 30 WHITE 27925 JOINER BULKHEADSONOBUOY STORE NO. 1 01JA2 23.9 STBD C212 36 36 C061 30 30 WHITE 27925SONOBUOY STORE NO. 1 01JA2 18.8 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480SONOBUOY STORE NO. 1 01JA2 13.1 OTHERS C061 30 30 GREY 16076 DADO (900mm HIGH)

SPORTS GEAR STORE 01JZ1 6.9 ST DECK TRAFFIC C413 125-150 C200 750-1000 GREY 36076

SPORTS GEAR STORE 01JZ1 5.5 ST DECK NON TRAFFIC

C413 AND C045 C061 OR C177 30 30 GREY 16076

SPORTS GEAR STORE 01JZ1 8.6 DECKHEAD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925SPORTS GEAR STORE 01JZ1 15.8 FORWARD C212 36 36 NOTE 4 C061 30 30 WHITE 27925 PART INSULATIONSPORTS GEAR STORE 01JZ1 14.3 AFT C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925SPORTS GEAR STORE 01JZ1 25.3 PORT C212 36 36 NOTE 4 C061 30 30 WHITE 27925 PART INSULATIONSPORTS GEAR STORE 01JZ1 18.3 STBD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925SPORTS GEAR STORE 01JZ1 52.5 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480SPORTS GEAR STORE 01JZ1 16.8 OTHERS C061 30 30 GREY 16076 DADO (900mm HIGH)FDCR & DC SECTION BASE NO. 3 01JZ2 26.1 ST DECK C413 125-150 DK COVERINGFDCR & DC SECTION BASE NO. 3 01JZ2 20.8 DECKHEAD C212 36 36 INSULATION C061 30 30 WHITE 27925FDCR & DC SECTION BASE NO. 3 01JZ2 17.8 FORWARD C212 36 36 C061 30 30 WHITE 27925 CLEAR OF JOINER BULKHEADFDCR & DC SECTION BASE NO. 3 01JZ2 16.2 AFT C212 36 36 INSULATION NOTE 5 WHITE 27925FDCR & DC SECTION BASE NO. 3 01JZ2 19.0 PORT C212 36 36 INSULATION NOTE 5 WHITE 27925FDCR & DC SECTION BASE NO. 3 01JZ2 35.5 STBD C212 36 36 C061 30 30 WHITE 27925 CLEAR OF JOINER BULKHEADFDCR & DC SECTION BASE NO. 3 01JZ2 67.9 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480

E.C.M. COMPARTMENT 02EA 14.0 ST DECK TRAFFIC C413 125-150 C200 750-1000 GREY 36076

E.C.M. COMPARTMENT 02EA 10.7 ST DECK NON TRAFFIC

C413 AND C045 C061 OR C177 30 30 GREY 16076

E.C.M. COMPARTMENT 02EA 17.9 DECKHEAD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925E.C.M. COMPARTMENT 02EA 22.0 FORWARD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925E.C.M. COMPARTMENT 02EA 22.4 AFT C212 36 36 C061 30 30 WHITE 27925E.C.M. COMPARTMENT 02EA 14.4 PORT C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925E.C.M. COMPARTMENT 02EA 14.4 STBD C212 36 36 INSULATION NOTE 4 C061 30 30 WHITE 27925

E.C.M. COMPARTMENT 02EA 76.2 HOUSE SIDES OF E.C.M. COMP 76 C045 40 C411 30 30 30 GREY 26480

E.C.M. COMPARTMENT 02EA 1.9 COMPT TOP TRAFFIC C413 125-150 C200 750-1000 GREY 36076


Primer

DCZ Area M2

Surface1st Coat

µm


Name

Remarks

Rev: C


µm2nd Coat

µm


Finisher


µm3rd Coat

µm1st Coat

µm

E.C.M. COMPARTMENT 02EA 14.7 COMPT TOP NON-TRAFFIC

C413 AND C045 C061 OR C177 30 30 30 GREY 16076

FER UPTAKES(19600 G.T. FLAT TO TOP OF FUNNEL) 02FZ 22.3 ST DECK (19600

G.T. FLAT) 76 C045 40 C076 30 30 BLACK 17038

FER UPTAKES(19600 G.T. FLAT TO TOP OF FUNNEL) 02FZ 21.2 FER UPTAKES

TOP UNDERSIDE 76 C045 40 C076 30 30 BLACK 17038

FER UPTAKES(19600 G.T. FLAT TO TOP OF FUNNEL) 02FZ 25.5 FORWARD 76 C045 40 C076 30 30 BLACK 17038

FER UPTAKES(19600 G.T. FLAT TO TOP OF FUNNEL) 02FZ 21.1 AFT 76 C045 40 C076 30 30 BLACK 17038

FER UPTAKES(19600 G.T. FLAT TO TOP OF FUNNEL) 02FZ 18.6 PORT 76 C045 40 C076 30 30 BLACK 17038

FER UPTAKES(19600 G.T. FLAT TO TOP OF FUNNEL) 02FZ 18.6 STBD 76 C045 40 C076 30 30 BLACK 17038

FER UPTAKES(19600 G.T. FLAT TO TOP OF FUNNEL) 02FZ 77.4 OUTSIDE OF


WEATHER DECK, HANGAR TOP (FR 37.5 TO FR 48 ) 02J 112.6 ST DECK

TRAFFIC C413 125-150 C200 750-1000 GREY 36076

WEATHER DECK, HANGAR TOP (FR 37.5 TO FR 48 ) 02J 38.4 ST DECK NON

TRAFFICC413 AND

C045 C061 OR C177 30 30 GREY 16076

1 DECK, WEATHER DECK (FR 12 TO FWD) N/A 128.2 ST DECK TRAFFIC C413 125-150 C200 750-1000 GREY 36076

1 DECK, WEATHER DECK (FR 12 TO FWD) N/A 42.7 ST DECK NON TRAFFIC

C413 AND C045 C061 OR C177 30 30 30 GREY 16076

1 DECK, WEATHER DECK (FR 20.75 TO FR 40) N/A 267.9 ST DECK TRAFFIC C413 125-150 C200 750-1000 GREY 36076

1 DECK, WEATHER DECK (FR 20.75 TO FR 40) N/A 107.3 ST DECK NON TRAFFIC

C413 AND C045 C061 OR C177 30 30 GREY 16076

1 DECK, WEATHER DECK (FR 48 TO FR 59) N/A 341.4 ST DECK C413 125-150 C200 750-1000 GREY 36076

1 DECK, WEATHER DECK (FR 59 TO TRANSOM) N/A 73.3 ST DECK TRAFFIC C413 125-150 C200 750-1000 GREY 36076

1 DECK, WEATHER DECK (FR 59 TO TRANSOM) N/A 38.9 ST DECK NON TRAFFIC

C413 AND C045 C061 OR C177 30 30 GREY 16076

1 DECK, WEATHER DECK (LSO COMPT CANOPY) N/A 2.5 SHELL EXT 76 C045 40 C411 30 30 30 GREY 26480

01 DECK, WEATHER DECK (FR 12 TO FR 22 ) N/A 47.4 ST DECK TRAFFIC C413 125-150 C200 750-1000 GREY 36076

01 DECK, WEATHER DECK (FR 12 TO FR 22 ) N/A 90.0 ST DECK NON TRAFFIC

C413 AND C045 C061 OR C177 30 30 GREY 16076

01 DECK, WEATHER DECK (FR 39 TO FR 45 ) N/A 41.9 ST DECK TRAFFIC C413 125-150 C200 750-1000 GREY 36076

01 DECK, WEATHER DECK (FR 39 TO FR 45 ) N/A 30.6 ST DECK NON TRAFFIC

C413 AND C045 C061 OR C177 30 30 GREY 16076

02 DECK, WEATHER DECK, BRIDGE TOP (FR 12 TO FR 20.5 ) N/A 126.0 ST DECK

TRAFFIC C413 125-150 C200 750-1000 GREY 36076

02 DECK, WEATHER DECK, BRIDGE TOP (FR 12 TO FR 20.5 ) N/A 23.2 ST DECK NON

TRAFFICC413 AND

C045 C061 OR C177 30 30 GREY 16076

AAMR CASING TOP (FR 48 -36) N/A N/A 76 C045 40 C411 30 30 30 GREY 26480ACCOMM LADDER STEP PLATE - BASE N/A N/A C212 36 36 C411 30 30 30 GREY 26480ACCOMM LADDER STEP PLATE - LETTERS N/A N/A C212 36 36 C061 30 30 BLACK 17038AIR SEARCH RADAR MAST N/A N/A 76 C045 40 C411 30 30 30 GREY 26480 EXTERIORANCHOR N/A N/A 76 C045 40 C411 30 30 30 GREY 26480

ANCHOR CHAIN N/A N/A 76 C045 40 C061 30 30 30 WHITE 27925 ONE COAT BOILED LINSEED OIL C002 (VENDOR APPLIED) REF DWG NO 5


Primer

DCZ Area M2

Surface1st Coat

µm


Name

Remarks

Rev: C


µm2nd Coat

µm


Finisher


µm3rd Coat

µm1st Coat

µm

ANCHOR CHAIN N/A N/A 76 C045 40 C061 30 30 30 RED 11350 ONE COAT BOILED LINSEED OIL C002 (VENDOR APPLIED) REF DWG NO 5

ANCHOR CHAIN N/A N/A 76 C045 40 C061 30 30 30 BLUE 15052 ONE COAT BOILED LINSEED OIL C002 (VENDOR APPLIED) REF DWG NO 5

AWNING STANCHIONS N/A N/A C045 40 C061 30 30 30 WHITE 27925

BILGE KEELS N/A N/ATWICE FILLED & DRAINED WITH C161 ALLOWING 24 HOURS BETWEEN COATS

BOAT DAVIT (FR 36 - 28) N/A N/A 76 C045 40 C411 30 30 30 GREY 26480BOLLARDS, FAIRLEADS, EYEPADS & CLEATS -WEATHER DECK N/A N/A 76 C045 40 C061 30 30 30 BLACK 17038

BREAKWATER (FR 12 TO FWD) N/A N/A 76 C045 40 C411 30 30 30 GREY 26480BULLRING (FR 12 TO FWD) N/A N/A 76 C045 40 C061 30 30 30 BLACK 17038

C5 SONAR HYDRAULIC DOWN-LOCK ASSY, CYLINDER HOUSING ONLY N/A N/A INTERGARD

251 62 INTERGARD 740 45 GREY 26480 DEGREASE WITH C070 PRIOR TO

PAINTING

C5 SONAR HYDRAULIC DOWN-LOCK ASSY, EXCL CYLINDER HOUSING + ROD N/A N/A C212 36 36 C061 30 30 30 GREY 26480

CABLE HANGERS N/A N/A C212 36 C061 30 30 FINISH COLOURS TO BE THE SAME AS THE ADJACENT STRUCTURE

CHAIN PIPE (INTERIOR) N/A N/A 76 C183 64CHAIN PIPE BOLSTER (FR 12 TO FWD) N/A N/A 76 C045 40 C061 30 30 30 BLACK 17038

COVERING (DECK COVERING) N/A N/A C061 30 30 GREY 16076 FINISH COLOURS TO BE THE SAME AS THE ADJACENT STRUCTURE

CRPP HYDRAULIC COMPONENTS - HUBS (INTERNAL), OIL TUBES (OUTER SURFACES) N/A N/A PAINTED WITH KERATOL KD3 PAINT

DECK MARKINGS (VERTREP) (FR 12 TO FWD) N/A N/A C177 30 YELLOW 13655 REFER TO SPEC B-OG-282-000/FP-000 (SHOP) & STANAG 1162

DOORS (JOINER) N/A N/A 76 C045 40 C061 30 30

A COATING SYSTEM AND COLOUR SCHEME IDENTICAL TO THE PAINTED SURROUNDING SURFACE WHEN IN THE CLOSED POSITION

DOORS WT & AT N/A N/A 76 C045 40


DRAFT MARKS - ABOVE BOOT TOPPING N/A N/A C061 30 30 BLACK 17038DRAFT MARKS - FROM TOP OF BOOT TOPPING DOWN TO KEEL N/A N/A C061 30 30 WHITE 27925

DRAFT MARKS - PENNANT NUMBERS N/A N/A C061 30 30 BLACK 17038

EDFW EXPANSION TANK N/A N/A C021 125 WHITE

EDFW EXPANSION TANK N/A N/A C021 125 GREY

EDFW EXPANSION TANK N/A N/A C021 125 WHITE

ENGINE CASING EXTERIOR (FR 36 - 28) N/A N/A 76 C045 40 C411 30 30 30 GREY 26480ENSIGN STAFF (AFT - FR 48) N/A N/A C045 40 C061 30 30 30 WHITE 27925EXTERIOR DOORS/HATCHES - FLASHING N/A N/A C045 40 C061 30 30 BLACK 17038EXTERIOR DOORS/HATCHES - LEVER NUTS FOR FABRICATED LOCKERS N/A N/A C183 64 C207 125 GREY

EXTERIOR DOORS/HATCHES - WOODEN RAMPS FOR HATCH COAMINGS N/A N/A C099 14 18 NOTE 19 C099 22 22 22 CLEAR NON-SLIP AGGEGATE TO BE ADDED

TO FIRST FINISHER COAT


Primer

DCZ Area M2

Surface1st Coat

µm


Name

Remarks

Rev: C


µm2nd Coat

µm


Finisher


µm3rd Coat

µm1st Coat

µm

EXTERIOR OF VENTILATION & AIR-CONDITIONING TRUNKING (ALUM) - INSULATED N/A N/A C045 40 INSULATION NOTE 4 FINISH COLOURS TO BE THE SAME

AS THE ADJACENT STRUCTURE

EXTERIOR OF VENTILATION & AIR-CONDITIONING TRUNKING (ALUM) - NOT INSULATED

N/A N/A C045 40 FINISH COLOURS TO BE THE SAME AS THE ADJACENT STRUCTURE

EXTERIOR OF VENTILATION & AIR-CONDITIONING TRUNKING (STEEL) - INSULATED N/A N/A C212 36 INSULATION NOTE 4 FINISH COLOURS TO BE THE SAME

AS THE ADJACENT STRUCTUREEXTERIOR OF VENTILATION & AIR-CONDITIONING TRUNKING (STEEL) - NOT INSULATED


FAMR CASING TOP & ECM COMPARTMENT TOP (FR 28 - 12) N/A N/A 76 C045 40 C411 30 30 30 GREY 26480

FISH TAIL GUIDE BARS (AFT - FR 48) N/A N/A 76 C045 40 C061 30 30 30 GREEN 14120FLAG STAFF (FR 12 TO FWD) N/A N/A C045 40 C061 30 30 30 WHITE 27925

FLIGHT DECK MARKINGS (AFT - FR 48) N/A N/A 3600-05A C177 30 30 YELLOW 13655 REFER TO SPEC D0003/F/6000/B-0G-282-000/FP-000 AND STANAG 1162

FLIGHT DECK MARKINGS (AFT - FR 48) N/A N/A 3600-05B C177 30 30 WHITE 17925 REFER TO SPEC D0003/F/6000/B-0G-282-000/FP-000 AND STANAG 1162

FOUNDATIONS & BACKGROUND (FR 28 - 12) N/A N/A 76 C045 40 C061 30 30 30 BLACK 17038FUNNEL EXTERIOR (FR 36 - 28) N/A N/A 76 C045 40 C411 30 30 30 GREY 26480FUNNEL TOP (FR 36 - 28) N/A N/A 76 C045 40 C076 30 30 30 BLACK 17038GASOLINE CANISTER STOWAGE RACK (FR 48-36) N/A N/A 76 C045 40 C411 30 30 30 GREY 26480

GUARD RAIL STANCHIONS & LIFELINES -EXTERIOR N/A N/A C045 40 C061 30 30 30 WHITE 27925

GUN SEAT NO.1 DECK (FR 12 TO FWD) N/A N/A INTERIOR SURFACE 76 C207 125 GREY

GUN SEAT NO.1 DECK (FR 12 TO FWD) N/A N/A INTERIOR SURFACE 76 C207 125 WHITE

GUN SEAT NO.1 DECK (FR 12 TO FWD) N/A N/A EXTERIOR SURFACE 76 C045 40 C411 30 30 30 GREY 16076

HANGAR FACE & TOP MARKINGS (FR 48 - 36) N/A N/A C061 30 YELLOW 13655 REFER TO SPEC D0003/F/6000/B-0G-282-000/FP-000 AND STANAG 1162

HANGAR SIDES (AFT EXTERIOR SHELL) N/A N/A 76 C045 40 C411 30 30 30 GREY 26480HATCHES- EXTERIOR N/A N/A 76 C045 40 C411 30 30 30 GREY 26480HATCHES -EXTERIOR, FUNNEL TOP W.T. FLAT N/A N/A 76 C045 40 C076 30 30 BLACK 17038

HATCHES -TOPSIDE N/A N/A 76 C045 40 C061 30 30


HATCHES -UNDERSIDE N/A N/A C212 36 36 C061 30 30 WHITE 27925


HAWSE PIPE BOLSTER (FR 12 TO FWD) N/A N/A 76 C045 40 C061 30 30 30 BLACK 17038HAWSE PIPE -INTERIOR N/A N/A 76 C183 64

HELICOPTER TROUGH & DRAINS (AFT - FR 48) N/A N/A 76 C045 40 C061 30 30 30 GREEN 16076 WHERE FINISHER COATS ARE REQUIRED I.E. TOP PLATES

HIGH TEMPERATURE DUCTING (INSULATED) - AUXILIARY BOILERS N/A N/A C143 25 25 INSULATION NOTE 4 C076 30 30 GREY 26480

HIGH TEMPERATURE DUCTING (INSULATED) - CRUISE ENGINES (DIESEL) N/A N/A C143 25 25 INSULATION NOTE 4 C076 30 30 GREY 26480


Primer

DCZ Area M2

Surface1st Coat

µm


Name

Remarks

Rev: C


µm2nd Coat

µm


Finisher


µm3rd Coat

µm1st Coat

µm

HIGH TEMPERATURE DUCTING (INSULATED) - DIESEL GENERATOR N/A N/A C143 25 25 INSULATION NOTE 4 C076 30 30 GREY 26480

HIGH TEMPERATURE DUCTING (INSULATED) - INCINERATOR N/A N/A C143 25 25 INSULATION NOTE 4 C076 30 30 GREY 26480

HIGH TEMPERATURE DUCTING (INSULATED) - MAIN ENGINES (GAS TURBINES) S, ST N/A N/A INSULATION NOTE 4 C076 30 30 GREY 26480

HOSE RACK (FIRE FIGHTING) N/A N/A C045 40 C061 30 30 30 RED 11350 FINISH COLOURS TO BE THE SAME AS THE ADJACENT STRUCTURE

HOUSE FRONT -EXTERIOR (FR 12 TO FWD) N/A N/A 76 C045 40 C411 30 30 30 GREY 26480HOUSE SIDES -EXTERIOR (FR 48 - 36) N/A N/A 76 C045 40 C411 30 30 30 GREY 26480HOUSE SIDES -EXTERIOR, 1 DK TO 01 DK, 01 DK TO 02 DK, 02 DK TO TOP OF ECM COMPARTMENT & FAMR CASING

N/A N/A 76 C045 40 C411 30 30 30 GREY 26480

IDENTIFICATION & CBRND RISK MARKINGS N/A N/A C061 30 RED 11350IDENTIFICATION & CBRND RISK MARKINGS N/A N/A C061 30 BLUE 15052IDENTIFICATION & CBRND RISK MARKINGS N/A N/A C061 30 ORANGE 12473IDENTIFICATION & CBRND RISK MARKINGS N/A N/A C061 30 BLACK 17038IDENTIFICATION & CBRND RISK MARKINGS N/A N/A C061 30 YELLOW 13538IDENTIFICATION & CBRND RISK MARKINGS N/A N/A C061 30 GREEN 14120

INTERIOR OF THE SONAR DOME FAIRING BAND N/A N/A C207SEE

REMARKS

BUFF D.F.T. PER COAT IS 125-150 MICRONS

INTERIOR OF THE SONAR DOME FAIRING BAND N/A N/A C207SEE

REMARKS

OFF-WHITE D.F.T. PER COAT IS 125-150 MICRONS

INTERIOR OF VENTILATION & AIR-CONDITIONING TRUNKING (ALUM) (PRIMED ONLY PRIOR TO ERECTION)


INTERIOR OF VENTILATION & AIR-CONDITIONING TRUNKING (STEEL) (PRIMED ONLY PRIOR TO ERECTION)


JP5 FUEL SUMP TANK N/A N/A C193 125 GREY

JP5 FUEL SUMP TANK N/A N/A C193 125 WHITE

LADDERS & STAIRWAYS -EXTERIOR N/A N/A 76 C045 40 C411 30 30 30 GREY 26480LADDERS, SLOPED -INTERIOR N/A N/A C212 36 36 C061 30 30 GREY 16076 TREADS-UNPAINTEDLADDERS, VERTICAL -INTERIOR N/A N/A C212 36 36 C061 30 30 GREY 16076 OUTSIDE OF TANKS

MAIN FEED TANK, GREY WATER TANKS N/A N/A C207 SEE REMARK BUFF D.F.T. PER COAT IS 125-150 MICRONS

MAIN FEED TANK, GREY WATER TANKS N/A N/A C207 SEE REMARK OFF-WHITE D.F.T. PER COAT IS 125-150 MICRONS

MAIN MAST N/A N/A 76 C045 40 C411 30 30 30 GREY 26480

MAIN MAST N/A N/A LEGS INTERIOR 5769 40 40 RED

RUST-O-CRYLIC (FFH330 TO FFH332). PRIOR TO LEG ACCESS PLATES BEING CLOSED, A ZERUST PIPE STRIP CODE NUMBER PS-2-16 IS TO BE INSTALLED AND ACTIVATED IN ACCORDANCE WITH MANUFACTURERS INSTRUCTIONS.


Primer

DCZ Area M2

Surface1st Coat

µm


Name

Remarks

Rev: C


µm2nd Coat

µm


Finisher


µm3rd Coat

µm1st Coat

µm

MAIN MAST N/A N/A LEGS INTERIOR 5269 40 40 RED

RUST-O-CRYLIC (FFH333 TO FFH341) PRIOR TO LEG ACCESS PLATES BEING CLOSED, A ZERUST PIPE STRIP CODE NUMBER PS-2-16 IS TO BE INSTALLED AND ACTIVATED IN ACCORDANCE WITH MANUFACTURERS INSTRUCTIONS.

MAIN MAST N/A N/A CATWALKS/ PLATFORMS C413 125-150 C200 750-1000 GREY 36076

MAIN MAST - INTERIOR (MAIN SUPPORT LEGS) N/A N/A 5769 40 40

MANHOLE COVERS (TOP) N/A N/A C212 36 36 C061 30 30 GREY 16076


MAPLE LEAFS N/A N/A C045 40 C061 30 30 30 RED 11310

MOORING CHAIN N/A N/A 76 C045 40 C061 30 30 30 WHITE 27925 ONE COAT BOILED LINSEED OIL C002 (VENDOR APPLIED) REF DWG NO 5

NAVIGATION LIGHT SCREENS - PORT N/A N/A C045 40 C061 30 30 BLACK 17038NAVIGATION LIGHT SCREENS - STBD N/A N/A C045 40 C061 30 30 BLACK 17038PIPING SYSTEMS, COPPER & COPPER NICKEL COLD (INSULATED) N/A N/A INSULATION NOTE 4 C061 30 30 FINISH COLOURS TO BE THE SAME

AS THE ADJACENT STRUCTUREPIPING SYSTEMS, COPPER & COPPER NICKEL COLD (PAINTED) N/A N/A C045 40 C061 30 30 FINISH COLOURS TO BE THE SAME

AS THE ADJACENT STRUCTUREPIPING SYSTEMS, COPPER & COPPER NICKEL HOT (INSULATED) N/A N/A INSULATION NOTE 4 C061 30 30 FINISH COLOURS TO BE THE SAME

AS THE ADJACENT STRUCTUREPIPING SYSTEMS, COPPER & COPPER NICKEL HOT (PAINTED) N/A N/A C143 25 25 FINISH COLOURS TO BE THE SAME

AS THE ADJACENT STRUCTURE

PIPING SYSTEMS, MONEL, COLD (PAINTED) N/A N/A C045 40 C061 30 30 FINISH COLOURS TO BE THE SAME AS THE ADJACENT STRUCTURE

PIPING SYSTEMS, MONEL, HOT (PAINTED) N/A N/A C076 30 30 FINISH COLOURS TO BE THE SAME AS THE ADJACENT STRUCTURE

PIPING SYSTEMS, STAINLESS, COLD (PAINTED) N/A N/A C045 40 C061 30 30 FINISH COLOURS TO BE THE SAME AS THE ADJACENT STRUCTURE

PIPING SYSTEMS, STAINLESS, HOT (PAINTED) N/A N/A C143 25 FINISH COLOURS TO BE THE SAME AS THE ADJACENT STRUCTURE

PIPING SYSTEMS, STEEL, COLD (INSULATED) N/A N/A C212 36 INSULATION NOTE 4 C061 30 30 FINISH COLOURS TO BE THE SAME AS THE ADJACENT STRUCTURE

PIPING SYSTEMS, STEEL, COLD (PAINTED) N/A N/A C212 36 C061 30 30 FINISH COLOURS TO BE THE SAME AS THE ADJACENT STRUCTURE

PIPING SYSTEMS, STEEL, HOT (INSULATED) N/A N/A C143 25 INSULATION NOTE 4 C061 30 30 FINISH COLOURS TO BE THE SAME AS THE ADJACENT STRUCTURE

PIPING SYSTEMS, STEEL, HOT (PAINTED) N/A N/A C143 25 25 FINISH COLOURS TO BE THE SAME AS THE ADJACENT STRUCTURE

PORTABLE DAVITS N/A N/A 76 C045 40 C411 30 30 30 GREY 26480RADHAZ MARKINGS 01, 02 DK & FER CASING TOP (FR 28 - 12) N/A N/A C177 AND C061 30 WHITE 17925 REFER TO SPEC 8-0G-282-000/FP-000

(SHOP) AND STANAG 1162RADHAZ MARKINGS 01, 02 DK & FER CASING TOP (FR 28 - 12) N/A N/A C177 AND C061 30 RED 11350 REFER TO SPEC 8-0G-282-000/FP-000

(SHOP) AND STANAG 1162RAS POST TRUNK (FR 12 TO FWD) N/A N/A 76 C045 40 C411 30 30 30 GREY 26480SAFETY NET STANCHIONS (AFT - FR 48) N/A N/A C045 40 C061 30 30 30 WHITE 27925

SAFETY/WARNING MARKINGS (FR 12 TO FWD) N/A N/A 76 C045 40 C061 30 RED 11350 REFER TO SPEC B-OG-282-000/FP-000 (SHOP) & STANAG 1162

SAFETY/WARNING MARKINGS (FR 28 - 12) N/A N/A C061 30 RED 11350 REFER TO SPEC 8-0G-282-000/FP-000 (SHOP) AND STANAG 1162


Primer

DCZ Area M2

Surface1st Coat

µm


Name

Remarks

Rev: C


µm2nd Coat

µm


Finisher


µm3rd Coat

µm1st Coat

µm

SAFETY/WARNING MARKINGS HANGAR TOP (FR 48 - 36) N/A N/A C061 30 RED 11350 REFER TO SPEC 8-0G-282-000/FP-000

(SHOP) AND STANAG 1162

SCUTTLES (TOPSIDE) N/A N/A 76 C045 40 C061 30 30


SCUTTLES (UNDERSIDE) N/A N/A C212 36 36 C061 30 30 RED 11310


SCUTTLES -EXTERIOR N/A N/A 76 C045 40 C061 30 30 30 GREY 16076

SEATING (BULKHEAD) N/A N/A C212 36 36 C061 30 30 FINISH COLOURS TO BE THE SAME AS THE ADJACENT STRUCTURE

SEATING (DECKHEAD) N/A N/A C212 36 36 C061 30 30 WHITE 27925 FINISH COLOURS TO BE THE SAME AS THE ADJACENT STRUCTURE

SEATINGS (ENCLOSED) N/A N/A C207 125 GREY FINISH COLOURS TO BE THE SAME AS THE ADJACENT STRUCTURE

SEATINGS (ENCLOSED) N/A N/A C207 125 WHITE FINISH COLOURS TO BE THE SAME AS THE ADJACENT STRUCTURE

SEATINGS (STANDING DECK) N/A N/A C212 36 36 C061 30 30 GREY 16076 FINISH COLOURS TO BE THE SAME AS THE ADJACENT STRUCTURE

SEATINGS -WEATHER DECK N/A N/A ENCLOSED AREA C207 125 GREY

SEATINGS -WEATHER DECK N/A N/A ENCLOSED AREA C207 125 WHITE

SEATINGS -WEATHER DECK N/A N/A EXTERIOR 76 C045 40 C061 30 30 30 GREY 16076SHADED STERN LIGHT - BOX N/A N/A 76 C045 40 C061 30 30 30 BLACK 17038SHADED STERN LIGHT - MASTHEAD & OVERTAKING LIGHT SCREENS N/A N/A C045 40 C061 30 30 30 WHITE 27925 (ALUM)

SHADED STERN LIGHT - REFLECTOR N/A N/A 76 C045 40 C061 30 30 30 WHITE 27925

SONAR DOME FAIRING MOUNTING BOLT HEADS, SHANK & UNUSED THREADS N/A N/A C207

SEE REMARK

SBUFF D.F.T. PER COAT IS 125-150 MICRONS

SONAR DOME FAIRING MOUNTING BOLT HEADS, SHANK & UNUSED THREADS N/A N/A C207

SEE REMARK

SOFF-WHITE D.F.T. PER COAT IS 125-150 MICRONS

SONAR DOME MOUNTING NUTS & STUDS N/A N/A C207SEE

REMARKS

BUFF

THE LOWER PART OF THE THREAD ON THE STUDS IS TO BE PAINTED PRIOR TO DOME INSTALLATION. THE UPPER PART OF THE STUD'S THREAD AND THE NUT ARE TO BE PAINTED AFTER THE NUTS ARE IN PLACE AND TORQUED. D.F.T. PER COAT IS 125-150 MICRONS.

SONAR DOME MOUNTING NUTS & STUDS N/A N/A C207SEE

REMARKS

OFF-WHITE

THE LOWER PART OF THE THREAD ON THE STUDS IS TO BE PAINTED PRIOR TO DOME INSTALLATION. THE UPPER PART OF THE STUD'S THREAD AND THE NUT ARE TO BE PAINTED AFTER THE NUTS ARE IN PLACE AND TORQUED. D.F.T. PER COAT IS 125-150 MICRONS.

STOWAGE LAMP, SMOKE MARKER AND SUS LOCKERS (FR 28 - 12) N/A N/A ALL 76 C045 40 C411 30 30 30 GREY 26480


Primer

DCZ Area M2

Surface1st Coat

µm


Name

Remarks

Rev: C


µm2nd Coat

µm


Finisher


µm3rd Coat

µm1st Coat

µm

TANKS NONSTRUCTURAL (INTERIOR):- INCINERATOR FUEL TANK, SOLVENT TANK, DIESEL DRIVEN FIRE PUMP DAY TANKS, LUBE OIL READY USE TANK, EMERGENCY FUEL TANK LO CENTRIFUGE DRAIN TANKS, FO CENTRIFUGE SLUDGE TANKS, CRPP HYDRAULIC TANKS, SONAR DOME MTG PLT THREADED HOLES

N/A N/A 31-GP-3A 25

TOWING BRACKETS, TOWING CLEATS & FITTINGS -WEATHER DECK N/A N/A 76 C045 40 C061 30 30 30 BLACK 17038

WAVEGUIDES (EXTERIOR) N/A N/A C045 40 C411 30 30 30 GREY 26480 NON-FERROUS

WINCH SEAT (FR 12 TO FWD) N/A N/A INTERIOR SURFACE C207 125 GREY

WINCH SEAT (FR 12 TO FWD) N/A N/A INTERIOR SURFACE C207 125 WHITE

WINCH SEAT (FR 12 TO FWD) N/A N/A EXTERIOR SURFACE 76 C045 40 C411 30 30 30 GREY 26480

WOOD - VARNISHED, LADDERS, BOOMS, STAFFS, SPURNWATER, BOARD (ASHORE & ON N/A N/A C099 14 18 NOTE 16 C099 22 22 CLEAR

WOODEN SCREENS (FR 28 - 12) N/A N/A C125 40 C061 30 30 30 BLACK 17038 PRIMER COAT THINNED 10% SANDED LIGHTLY BETWEEN COATS