HT417/HT417H HAY TEDDER - Bush Hog

Important Operatingand Safety Instructionsare found in the MowerSafety Video that canbe instantly accessedon the internet at:www.algqr.com/bve

An Operator’s Manual was shipped with the

equipment. The Operator’s Manual is an integral

part of the safe operation of this machine and

must be maintained with the unit at all times.

READ, UNDERSTAND, and FOLLOW the

Safety and Operation Instructions contained in

this manual before operating the equipment. If

the Operator’s Manual is not with the equipment,

contact your dealer or Bush Hog to obtain a copy

before operating the equipment.

PARTS MANUALSECTION 17

Published 05/12 MATERIAL HANDLING PARTS MANUAL

HT417/HT417H

HAY TEDDER

©2009 Alamo Group Inc.

PARTS ORDERING GUIDE

The following instructions are offered to help eliminate needless delay and error in pro-cessing purchase orders for the equipment in this section.

1. The Parts Section is prepared in logical sequence and grouping of parts that belong to the basic machine featured in this manual. Part Numbers and Descriptions are given to help locate the parts and quantities required.

2. The Purchase Order must include the name and address of the person or organiza-tion ordering the parts, who should be charged, and if possible, the serial number of the machine for which the parts are ordered.

3. The Purchase Order must clearly list the quantity of each part, the complete and correct part number (be sure to include all periods), and the basic name of the part.

4. The Manufacturer reserves the right to substitute parts where applicable.

5. Some parts are unlisted items which are special production items not normally stocked and are subject to special handling. Request a quotation for such parts before sending a Purchase Order.

6. The Manufacturer reserves the right to change prices without prior notice.

For maximum safety and to guarantee optimum product reliability, always use genuine BUSH HOG Parts. The use of inferior replacement parts may causepremature or catastrophic failure which could result in serious injury or death.Direct any questions regarding parts to:

BUSH HOG2501 Griffin Ave. Selma, AL 36703www.bushhog.comContact Us800-304-2836

To the Owner/Operator/Dealer

All implements with moving parts are potentially hazardous. There is no substitute for a cautious, safe-mindedoperator who recognizes the potential hazards and follows reasonable safety practices. The manufacturer hasdesigned this implement to be used with all its safety equipment properly attached to minimize the chance ofaccidents.

BEFORE YOU START! Read the safety messages on the implement and shown in your manual. Observe the rulesof safety and common sense!

WARRANTY INFORMATION:Read and understand the complete Warranty Statement found in this Manual. Fill out the Warranty RegistrationForm in full and return it to within 30 Days. Make certain the Serial Number of the Machine is recorded on theWarranty Card and on the Warranty Form that you retain.

LIMITED WARRANTY

Bush Hog warrants to the original purchaser of any new Bush Hog equipment, purchased from an authorized BushHog dealer, that the equipment be free from defects in material and workmanship for a period of one (1) year fornon-commercial, state and municipalities’ use and ninety (90) days for commercial use from date of retail sale. Theobligation of Bush Hog to the purchaser under this warranty is limited to the repair or replacement of defectiveparts.

Replacement or repair parts installed in the equipment covered by this limited warranty are warranted for ninety(90) days from the date of purchase of such part or to the expiration of the applicable new equipment warrantyperiod, whichever occurs later. Warranted parts shall be provided at no cost to the user at an authorized Bush Hogdealer during regular working hours. Bush Hog reserves the right to inspect any equipment or parts which areclaimed to have been defective in material or workmanship.

DISCLAIMER OF IMPLIED WARRANTIES & CONSEQUENTIAL DAMAGESBush Hog’s obligation under this limited warranty, to the extent allowed by law, is in lieu of all warranties, implied orexpressed, INCLUDING IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR APARTICULAR PURPOSE and any liability for incidental and consequential damages with respect to the sale oruse of the items warranted. Such incidental and consequential damages shall include but not be limited to:transportation charges other than normal freight charges; cost of installation other than cost approved by BushHog; duty; taxes; charges for normal service or adjustment; loss of crops or any other loss of income; rental ofsubstitute equipment, expenses due to loss, damage, detention or delay in the delivery of equipment or partsresulting from acts beyond the control of Bush Hog.

THIS LIMITED WARRANTY SHALL NOT APPLY:1. To vendor items which carry their own warranties, such as engines, tires, and tubes.

2. If the unit has been subjected to misapplication, abuse, misuse, negligence, fire or other accident.

3. If parts not made or supplied by Bush Hog have been used in connection with the unit, if, in the sole judgementof Bush Hog such use affects its performance, stability or reliability.

4. If the unit has been altered or repaired outside of an authorized Bush Hog dealership in a manner which, in thesole judgement of Bush Hog, affects its performance, stability or reliability.

5. To normal maintenance service and normal replacement items such as gearbox lubricant, hydraulic fluid, wornblades, or to normal deterioration of such things as belts and exterior finish due to use or exposure.

6. To expendable or wear items such as teeth, chains, sprockets, belts, springs and any other items that in thecompany’s sole judgement is a wear item.

NO EMPLOYEE OR REPRESENTATIVE OF BUSH HOG IS AUTHORIZED TO CHANGE THIS LIMITEDWARRANTY IN ANY WAY OR GRANT ANY OTHER WARRANTY UNLESS SUCH CHANGE IS MADE INWRITING AND SIGNED BY BUSH HOG’S SERVICE MANAGER, 2501 GRIFFIN AVE., SELMA, ALABAMA36703.

Record the model number, serial number and date

purchased. This information will be helpful to your

dealer if parts or service are required.

MAKE CERTAIN THE WARRANTY

HAS BEEN FILED WITH BUSH HOG

SELMA, ALABAMA

MODEL NUMBER ________________________________

SERIAL NUMBER ________________________________

DATE OF RETAIL SALE ___________________________

BUSH HOG/MATERIAL HANDLING REPAIR PARTS MANUAL MAY, 2012BUSH HOG/MATERIAL HANDLING REPAIR PARTS MANUAL

ALPHABETICAL TABLE OF CONTENTS

HT417/HT417H HAY TEDDER

ITEM PAGE NUMBER

NOTES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17-1-1

Axle Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17-1-2, 17-1-3

Axle Assembly 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17-1-4, 17-1-5

Decals - Bush Hog Marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17-1-16

Drawbar Assembly (Hydraulic Lift) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17-1-6, 17-1-7

Drawbar Assembly (Spring Lift) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17-1-11

Driveline Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17-1-8, 17-1-9

Gearbox Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17-1-10

Hydraulic Cylinder & Hose Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . .17-1-12, 17-1-13

Tire Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17-1-14, 17-1-15

Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Inside Back Cover

BUSH HOG/MATERIAL HANDLING REPAIR PARTS MANUAL APRIL, 2011

NOTES

17-1-1

BUSH HOG/MATERIAL HANDLING REPAIR PARTS MANUAL MAY, 2012

AXLE ASSEMBLY

* SPR

ING

LIF

T VE

RSI

ON

ON

LY (Q

TY. 2

)

** H

YDR

AU

LIC

LIF

T VE

RSI

ON

ON

LY (Q

TY. 6

)

**

*

*

MODELS HT417/HT417H

(SPRING & HYDRAULIC LIFT)

17-1-2


AXLE ASSEMBLY

REF. PARTNO. NO. DESCRIPTION QTY.

1 3676403 Plate, Gearbox Lock 12 3676404 Shaft, Input Gearbox 13 3676400 Housing, Gearbox 14 3676449 RH Center Axle Housing 15 3676450 LH Center Axle Housing 16 3670275 Reinforcement Housing 17 3676451 RH Fork Support Housing 18 3676452 LH Fork Support Housing 19 3676453 Drive Shaft, Output 110 3676900 Gasket, Gearbox 211 3676421 Shaft, Rotor 212 3676454 Tine Disc 213 3676455 Hub, Gearbox 214 3676779 Plug (Spring Lift Version) 2

3676779 Plug (Hyd. Lift Version) 615 3676904 Shim 216 3676417 Joint, Double U- 217 3676424 Yoke 218 3676425 Kit, Cross & Bearing 419 3676426 Yoke, Center Double 220 3676427 Yoke, Splined 221 --------- Guard, Plastic Shaft 122 3676778 Guard, IID Protection 123 3676800 Seal, Oil 35 x 52 x 10 124 00766021 Ring E35 UNI 7435 126 00764417 Bearing, Ball 1-1.77 ID x 3.346 OD 127 3676407 Plug, Gearbox Oil 228 3676802 Seal, Oil 30 x 62 x 10 129 3236004 Ball Bearing, 30 x 62 x 16 W/O Seal 230 3676801 Seal, Oil 30 x 56 x 10 131 3636003 Bearing, Ball Two Rubber Seals 232 00754459 Bearing, 35 x 72 x 17 533 3676405 Gear, Pinion 134 3676408 Gear, Crown 135 3676419 Gear, Pinion 236 3676456 Crown Gear 237 703616W Roll Pin, M10 x 55 238 703417W Roll Pin, M6 x 55 239 001465 Grease Fitting, Straight, M6 240 00766457 Grease Fitting M10 x 1.5 Str PG 241 710640 Key, Rnd End 8 x 7 x 40 242 710630 Rnd End Key 8 x 7 x 30 MM 243 3678401 Bolt, Stud M8 x 1.25 x 30 Gr 8.8 244 00755934 Nut, M8 x 1.25 245 70093C Locknut, Toplock M8 x 1.25 246 02958784 Bolt Metric M8 x 1.25 x 20 Gr 8.8 247 701611C Lockwasher, M8 248 --------- Capscrew, M12 x 1.75 x 45 449 701613C Lockwasher, M12 2850 00772648 Nut, M12 x 1.75 Gr 8.8 451 00766177 Capscrew, M12 x 1.75 x 45 Gr 8.8 852 00754565 Socket Head Capscrew, M12 x 1.75 x 35 2053 00762462 Capscrew, M12 x 1.75 x 25 Gr 8.8 12

17-1-3

MODELS HT417/HT417H(SPRING & HYDRAULIC LIFT)


* SPR

ING

LIF

T VE

RSI

ON

ON

LY

* *

* * * * * *

* ***

*

*

**

*

*

* * ** *

HYD

RA

ULI

C L

IFT

VER

SIO

N O

NLY

AXLE ASSEMBLY 2

17-1-4

MODELS HT417/HT417H



REF. PART

NO. NO. DESCRIPTION QTY.

1 3670276 RH Lateral Axle 12 3670277 LH Lateral Axle 13 3676457 Fork Housing 24 --------- Shaft, Gearbox Lateral 25 3677552 Inner Tube 26 3677424 Spring 27 3670278 Outer RH Tube 18 3670279 Outer LH Tube 19 3670227 Wdmt, Spring Hitch 2

10 3677517 Pin, Bent 211 3677423 Spring 212 3678702 Guard Flap-Rubber 213 3677553 Plate, Guard 214 3677554 Plate, Guard 215 3677518 Pin 416 3677515 Bushing 417 3636003 Bearing, Ball Two Rubber Seals 218 3678200 Ring, Ext. Retaining Snap E30 819 3678402 Screw, Set, M8 x 1.25 x 12 420 3676906 Shim 421 3676907 Shim 422 00754565 Socket Head Capscrew, M12 x 1.75 x 35 1423 701613C Lockwasher, M12 1424 61354C8 Capscrew, M8 x 1.25 x 16 Gr 8.8 825 701511C Lockwasher, M8 826 703415W Roll Pin, 6 MM x 45 MM 627 70349 Roll Pin, 6 MM x 26 MM 228 001465 Grease Fitting, Straight, M6 429 3678205 Ring, Ext. Retaining Snap E29 430 3670280 RH Lateral Axle 131 3670281 LH Lateral Axle 1

AXLE ASSEMBLY 2

17-1-5

MODELS HT417/HT417H



DRAWBAR ASSEMBLY

17-1-6

MODEL HT417H

(HYDRAULIC LIFT)


DRAWBAR ASSEMBLY

REF. PART


1 3670272 Drawbar 12 3670208 Wdmt, Center Guard 13 3670219 Wdmt, RH Lateral Guard 14 3670220 Wdmt, LH Lateral Guard 15 3670207 Wdmt, Stand 16 3670211 Pin 17 3677548 Pin, Drawbar 18 3670204 Wdmt, Handle 19 3677549 Pin 1

10 3677507 Screw, Tie Rod 111 3670271 Fork 112 3677550 Pin 113 3676776 Plug, Plastic 114 3638400 Hairpin, Cotter, M3 115 3676775 Plug,Plastic 616 703315W Roll Pin 517 70349 Roll Pin, 6 MM x 26 MM 118 001465 Grease Fitting, Straight, M6 319 3676907 Shim 220 70209C A12 External Serrated Washer 821 00762395 Capscrew M12 x 1.75 x 20 Gr 8.8 422 00762462 Capscrew M12 x 1.75 x 25 Gr 8.8 623 3678600 Rope 124 3677125 RH Cylinder 125 3677126 LH Cylinder 126 3670215 Wdmt, RH Coupler Latch 127 3670216 Wdmt, LH Coupler Latch 128 3677420 Spring, RH 129 3677421 Spring, LH 130 3670273 Hitch 231 3670274 Support 132 701613C Lockwasher, M12 233 3677511 Pin 234 3677551 Pin 235 703413W Roll Pin, M6 x 36 1036 703411 Roll Pin, M6 x 30 237 701513C Flatwasher, M12 638 00754565 Socket Head Capscrew M12 x 1.75 x 35 439 --------- Nut M12 x 1.75 Gr. 8.8 440 00762399 Capscrew M6 x 1 x 16 241 70092C Locknut, Toplock, M6 x 1 2

17-1-7

MODEL HT417H

(HYDRAULIC LIFT)


DRIVELINE ASSEMBLY

17-1-8

MODELS HT417/HT417H



DRIVELINE ASSEMBLY

REF. PART


3676461 Driveline Assembly 11 3616514 Yoke 12 3616429 Cross Journal Assembly 23 3616430 Outer Yoke Tube 14 703518W Flexible Pin 15 3616415 Cardan Tube 16 3616400 Cardan Tube 17 703517W Flexible Pin 18 3616432 Inner Tube Yoke 19 3616516 Torque Limiter LW3 S60 x 04 1

10 ------ Cone Shield Bell 03-04 211 ------ Outer Bearing 03-04 112 ------ Outer Base Cone 03-04 113 ------ Screw 614 ------ Outer Safety Tube 115 ------ Inner Safety Tube 116 ------ Cone, Inner Base 03-04 117 ------ Inner Bearing 03-04 118 ------ Chain 119 00756005 Label Danger Outer Drive Tube 120 00756004 External Shield Label 121 3616512 Ball Collar Kit 222 1416449 Grease Nipple 123 3616417 Casing w/Yoke 124 2516548 Ratchet Tooth 2425 3616517 Hub 126 2516550 Retaining Washer 127 2516551 Circlip 128 --------- Outer Half Shaft 129 --------- Inner Half Shaft 130 3616518 Safety Guard 1

17-1-9

MODELS HT417/HT417H



GEARBOX ASSEMBLY

REF. PART


1 3676458 Gearbox, Outer Housing 22 3676411 Shaft, Rotor 23 3676419 Gear, Pinion 24 3676456 Crown Gearbox 25 3676454 Tine Disc 26 3676455 Hub 27 3636003 Bearing, Ball Two Rubbe Seals 28 710630 Flat Key, Rnd End, 8 x 7 x 30mm 29 703616W Roll Pin, M10 x 55 2

10 703417W Roll Pin, M6 x 55 211 00754459 Bearing, 35 x 72 x 17 412 701613C Lockwasher, M12 813 00754565 Socket Head Capscrew, M12 x 1.75 x 35 814 61377C8 Capscrew, M12 x 1.75 x 30 Gr. 8.8 1215 00766457 Grease Fitting M10 x 1.5 Str PG 2

17-1-10

MODELS HT417/HT417H



DRAWBAR ASSEMBLY

REF. PART


1 3670270 Drawbar 12 3670208 Wdmt, Center Guard 13 3670210 Wdmt, RH Lateral Guard 14 3670209 Wdmt, LH Lateral Guard 15 3670207 Wdmt, Stand 16 3670211 Wdmt, Pin 17 3677548 Pin, Drawbar 18 3670204 Handle 19 3677549 Pin 1

10 3677507 Tie Rod 111 3670271 Fork 112 3677550 Pin 113 3676776 Plug, Plastic 114 3638400 Hairpin, Cotter, M3 115 3676775 Plug, Plastic 616 703315W Roll Pin 517 70349 Roll Pin, 6 MM x 26 MM 118 001465 Grease Fitting, Straight, M6 319 3676907 Shim 220 70209C A12 External Serrated Washer 821 00762395 Capscrew M12 x 1.75 x 20 Gr 8.8 422 00762462 Capscrew M12 x 1.75 x 25 Gr 8.8 4

17-1-11

MODEL HT417

(SPRING LIFT)


HYDRAULIC CYLINDER & HOSE ASSEMBLY

17-1-12

MODEL HT417H

(HYDRAULIC LIFT)


HYDRAULIC CYLINDER & HOSE ASSEMBLY

REF. PART


1 --------- Cylinder Tube, RH 12 --------- Cylinder Tube, LH 13 --------- Rod, Cylinder 24 --------- Spring, Cylinder 25 3687104 Head, Cylinder 26 --------- Piston, Cylinder 27 --------- Gasket 28 --------- Gasket 29 --------- Gasket 2

10 --------- Gasket 211 --------- Gasket 212 3677105 Kit, Seal 213 --------- Roll Pin, 3.5 MM x 18 MM 214 3677125 RH Cylinder, Complete 115 3677126 LH Cylinder, Complete 116 3677102 Bolt, Hydraulic 217 3678400 Washer, Copper 418 3677206 Hose (1/4”) 219 3677103 Tee, Hydraulic Union 120 3677104 Fitting, Hyd. Nipple Adapter 121 3677207 Hose (3/8”) 122 3638408 Copper Washer, 1/2 ID 123 3637102 Male Coupling Tip 124 3668424 Collar, Hose 625 --------- Socket Head Capscrew, Metric 6

17-1-13

MODEL HT417H

(HYDRAULIC LIFT)


TIRE ASSEMBLY

17-1-14

MODELS HT417/HT417H



TIRE ASSEMBLY

REF. PART


1 3670231 Wdmt, RH Support Spindle 12 3670230 Wdmt, LH Support Spindle 13 3670226 Wdmt, LH Center Support Spindle 14 3670225 Wdmt, RH Center Support Spindle 15 3677555 Spacer 46 3676908 Shim 47 3676909 Shim 48 3676905 Shim 49 3676903 Gasket 47, 63 x 3, 53 4

10 3677556 Arm, Tine 2411 3677422 Tine, Spring 2412 00766177 Capscrew M12 x 1.75 x 45 Gr 8.8 2413 3677512 Plate, Tine 2414 00772648 Locknut, Toplock M12 X 1.75 Gr. 10.9 4815 00754529 Capscrew, M12 x 1.75 x 30 Gr. 8.8 2416 00754565 Socket Head Capscrew, M12 x 1.75 x 35 2417 703616W Roll Pin, M10 x 55 418 703417W Roll Pin, M6 x 55 419 701613C Lockwasher, M12 2420 3678414 Washer 2421 3676700 Cover, Inside Dust 422 3676002 Bearing, Ball 6205 2RS 823 3677514 Spacer 424 3677600 Rim, 16 x 6.50-8 425 3677800 Tube 16 x 6.50 426 3677801 Tire 16 x 6.50-8 6 Ply 427 3676701 Cover, Outer Dust 428 701515C Flatwasher, M16 429 3038445 Locknut, Toplock M16 x 2.0 430 3670100 Tire Assy (16 x 6.50-8, 6 Ply) 4

17-1-15

MODELS HT417/HT417H


BUSH HOG/MATERIAL HANDLING REPAIR PARTS MANUAL APRIL, 2011

DECALS - BUSH HOG MARKING

MODELS HT417/HT417H

REF. PART


1 50068924 Decal, Model HT417 22 00725746 Decal, Peligro 13 00786980 Decal, Genuine Bush Hog Parts 14 999001 Decal, Warning - Tractor Weight 15 50068925 Decal, Model HT417H 26 3678303 Decal, Danger - Rotors 17 999200 Decal, General Warning - All Unit 18 00756004 Decal, Danger - Guard Missing 19 00763977 Decal, Important - Notice to Owner 1

10 00776031 Canister, Parts Manual 111 03200347 Emblem, SMV 112 00777394 Decal, Tow 113 02962764 Decal, Pinch Points 114 02965262 Decal, Warning-Oil Leak 115 50063360 Decal, Bush Hog 8” 216 2738332 Decal, Red Oblong Reflector 117 2738333 Decal, Yellow Oblong Reflector 118 00756005 Decal, Rotating Driveline (Not Shown) 1

1

4

7

10

3

6

9

2

5

8

11

12

13 14 15

16 17

17-1-16

Documents

HT417/HT417H HAY TEDDER - Bush Hog