HP.actualtests.hp2 Z26.v2014!03!17.by.rose

8/12/2019 HP.actualtests.hp2 Z26.v2014!03!17.by.rose

1/33


2/33

A

QUESTION 1A network administrator is building two IRF domains:

- One domain for the two distribution layer switches- One domain for the access layer switches

Each access layer switch should have a connection to each distribution layer switch. In this design, how manyaccess switches can the administrator have in the access layer IRF domain before spanning tree is required toremove loops between the two IRF domains?

A. 2

B. 4

C. 6

D. 8

E. 12

Correct Answer: CSection: (none)

Explanation

Explanation/Reference:

QUESTION 2A network administrator configures the following information on an HP Provision switch:

Provision(config)# spanning treeProvision(config)# spanning tree instance 0 priority 2

Based on this information, what is the priority assigned to this switch for instance 0?

A. 0B. 2

C. 4.096

D. 8.192

E. 16.384

Correct Answer: DSection: (none)Explanation


QUESTION 3


3/33

Switch-A and Switch-B are both configured for static LACP. User 1 is constantly sending traffic to the treeservers connected to Switch-A. A network administrator logs into Switch-B and executes these commands:


4/33


5/33

What is the state of the VLAN 1 interface?

A. All interfaces in VLAN 1 are down.

B. The IP address of VLAN 1 conflicts with another device in VLAN 1.

C. The IP address for VLAN 1 is a duplicate of another VLAN interface on the switch.

D. VLAN 1 has a single port in a down state.



QUESTION 5Which configuration tool do HP Provision switches support that HP Comware switches do not support?

A. Menu system

B. SNMP

C. Web-based

D. Auto configuration tool

Correct Answer:A

Section: (none)Explanation


QUESTION 6Which statements are true about the Network Time Protocol (NTP)? (Select two.)

A. It can deliver time-stamped messages via a multicast delivery system.

B. It delivers time-stamped messages using TCP to port 123.

C. The most precise time source is a stratum level 16 clock.

D. Timestamps can be digitally signed with certificates.

E. Timestamps can be digitally signed for verification.

Correct Answer:AESection: (none)Explanation


QUESTION 7


6/33

What are the participants in the 802 1X authentication process? (Select two.)

A. Supplicant

B. Client

C. Access point (AP)

D. Intermediary

E. Authenticator



QUESTION 8Which HP Provision switch command lists the operating system that is currently loaded?

A. Show boot-set

B. Show flashC. Show boot-files

D. Show version



QUESTION 9

Based on this topology, which statements are true? (Select two)

A. A break exists in the topology.

B. The topology is functioning normally.

C. There is a split stack.

D. This is a ring topology.

E. This is a daisy chain topology.

Correct Answer: BDSection: (none)Explanation


7/33


QUESTION 10

A network administrator needs to configure DHCP on an HP Comware switch. The network administratorconfigures the following information:

After setting up DHCP relay, the network administrator has the DHCP client try to acquire addressinginformation, but the process fails. What should the network administrator do to solve this problem?

A. Execute the r out i ng command on SwitchA.

B. Execute the dhcp enabl e command on SwitchA.

C. Configure DHCP relay on SwitchB.

D. Enable DHCP Snooping on SwitchA.

Correct Answer: BSection: (none)Explanation

Explanation/Reference:(Explanation: The correct answer is B. Choice A is incorrect because routing is enabled on Comware switches,by default. Choice C is incorrect because DHCP relay is not necessary on SwitchB since both ports are in

VLAN 3. Choice D is incorrect because DHCP Snooping is used to detect rogue DHCP servers. )

QUESTION 11Which HP Comware command saves the startup configuration file to a TFTP server?

A. Restore

B. Backup

C. Startup

D. Copy



QUESTION 12


8/33


9/33

A network administrator experiences a problem in which a user brought in a generic switch from home andconnected it to the network. The users switch does not support any spanning tree protocols. The users switch

has two connections to the network on switch ports that are defined as edge ports. Assume the companysswitches are HP ProVision switches.

Which solution effectively manages this problem?

A. BPDU Protection

B. Loop Protection

C. STP Protection

D. Root Protection

Correct Answer: BSection: (none)

Explanation


QUESTION 15Which standards do HP products support for Power over Ethernet (PoE)?

A. 802.1ah

B. 802 3af

C. 802.3at

D. 802.1az

E. 802.3av

Correct Answer: BCSection: (none)Explanation


10/33


QUESTION 16A network administrator is examining the routing table on an HP Comware switch. The network administratorsees two routes. 10.1.1.0/24, with the same neighbor's address (10.1.1.1). What would create this result?

A. There is an aggregated link with two connections between the two routers.

B. The bandwidth of the two routes is the same.

C. The administrative distance of the two routes is the same.

D. The cost of the two routes is the same.

Correct Answer:ASection: (none)Explanation


QUESTION 17

A company has two buildings that are 15 meters apart. The company needs to connect the buildings'networks. The CFO does not want the cost of installing fiber between the two buildings and thus is exploringwireless options.

If the company selects an 802 11n wireless solution, which wireless mode should they use?

A. Bridge mode

B. Infrastructure mode

C. In-cell relay mode

D. Point-to-Point mode

Correct Answer: CSection: (none)Explanation


QUESTION 18A network administrator is implementing a network with HP Comware and HP Provision switches. When thenetwork administrator boots the switches for the first time, what are the factory default settings of all of theswitches in the network? (Select two.)

A. All interfaces are enabled.

B. Routing is enabled.

C. SSH is enabled.D. DHCP client is defined for all VLANs.

E. No passwords are defined.




11/33

QUESTION 19Refer to the link aggregation between two HP switches.

The link aggregation is failing between the HP Provision and HP Comware switches. Which solution solves thisproblem?

A. The Provision switch must be reconfigured for static LACP.

B. TheProvision switch must be reconfigured for dynamic link aggregation.

C. TheComware switch must be reconfigured for dynamic LACP active mode.

D. TheComware switch must be reconfigured for static LACP.



QUESTION 20A network administrator has an HP Comware switch that is configured with OSPF. The network administratorviews the routing table and sees that a default route was learned from an OSPF neighbor (10.1.1.1). However,the network administrator wants to override this action and use a different neighbor (10.1.1.2) for the defaultroute.

The network administrator configures this command:

[Commware] ip route-static 0.0.0.0 0 10.1.1.2

After configuring the command, the network administrator examines the routing table and notices that theoriginal neighbor's default route is still in the routing table, but the static route is missing.

What is the cause of this problem?

A. OSPF routes have a lower precedence value.

B. Only one routing protocol can be operational on a Comware device.

C. The ip default-gate way command must be used when creating a default route.

D. The static route has a syntax mistake.


12/33


13/33


QUESTION 24Which HP Provision and HP Comware commands restore a configuration file from a TFTP server to theswitches' flash? (Select two.)

A. Restore startup-configuration from 10.1.1.1 config.cfg

B. Copy tftp://10.1.1.1/config.cfg flash:

C. Restore tftp://10.1.1.1/startup-configuration config.cfg

D. Copy tftp 10.1.1.1 config.cfg config config.cfg pc

E. Copy tftp config config.cfg 10.1.1.1 config.cfg pc



QUESTION 25Which Software-Defined Network (SDN) layer includes HP Provision and HP Comware switches?

A. Infrastructure

B. Application

C. Operational

D. Control



QUESTION 26Which IMC agent starts and stops the IMC server and allows a network administrator to view the status of theIMC processes?

A. IMC Processing Agent (IPA)

B. Deployment Monitoring Agent (DMA)

C. Policy Administration Agent (PAA)

D. Administration Deployment Agent (ADA)



QUESTION 27


14/33

Switch 1 and 2 are HP Provision switches. VLAN 33 has been defined as the management VLAN on bothswitches. Switch 1 is a layer 2 switch, and switch 2 is a layer 3 switch, with routing configured.

Based on this topology, which management connections to Switch 1 are out-of-band? (Select two)

A. User4

B. User-1

C. User-3

D. User-1

E. User-2

Correct Answer: CESection: (none)Explanation


QUESTION 28Refer to the partial command output.


15/33

Based on this output, which statement is true?

A. Static LACP is used, and load sharing is functioning.

B. Dynamic LACP is used, and load sharing has failed.

C. Static LACP is used, and load sharing has failed.

D. Dynamic LACP is used, and load sharing is functioning.



QUESTION 29Based on the default precedence used to rank routing protocols in HP Comware switches, if a default route(0.0.0.0/0) is learned from multiple routing protocols, which source would the Comware operating systemprefer?

A. Static

B. RIP

C. External BGP

D. Internal OSPF



QUESTION 30

A.

Correct Answer:A




16/33

QUESTION 31


17/33

A network administrator has created a layer 2 network based on the design shown in the exhibit. Switch-A andSwitch-B are distribution layer switches. Switch-C is an access layer switch. What is the best spanning treesolution for this environment?

A. STP

B. RSTP

C. PVST+

D. MSTP

Correct Answer: D



QUESTION 32A network administrator has installed IMC and the appropriate licenses. The network administrator isattempting to import the HP Comware and HP Provision switches into IMC but is experiencing problemsimporting the Comware switches. The network administrator verifies the SNMPv2c configuration on both setsof switches and the SNMP configuration in IMC. The SNMP parameters are correct.

What is the cause of the import problem?

A. Comware switches are not fully supported by IMC.

B. Comware switches implement SNMPv3 by default.

C. Comware switches require SSH to be configured for remote CLI access.

D. Comware switches do not have telnet fully configured.



18/33


19/33

A network administrator needs to configure link aggregation using static LACP on Switch-A. Which is an HP

Comware switch. Which configuration accomplishes this goal?

A.

B.


20/33

C.

D.



QUESTION 36

What is the default state of spanning tree on HP Comware switches?

A. MSTP is enabled.

B. RSTP is enabled.

C. STP is disabled.

D. PVST is enabled.

Correct Answer: C



QUESTION 37Refer to the network exhibit.


21/33

Assume the network shown in the exhibit has implemented RSTP Based on the topology, which ports are rootports? (Select two)

A. SwitchA port 2

B. SwitchB port 2

C. SwitchB port 1

D. SwitchD port 2

E. SwitchC port 2

Correct Answer:ACSection: (none)Explanation


QUESTION 38A network administrator has two distribution layer switches and four access layer switches. The networkadministrator is constantly resolving spanning tree problems and is looking for an alternative solution thatprovides redundancy and no spanning tree. Which solutions meet the network administrators requirements?(Select two)

A. HP ProVision switches with IRF

B. HP ProVision switches with distributed trunking

C. HP ProVision switches with routing

D. HP Comware switches with IRF

E. HP Comware switches with distributed trunking

Correct Answer: BDSection: (none)


22/33

Explanation


QUESTION 39Refer to the network and ARP table exhibit.

The user on the left side of the exhibit wants to build a connection to the server on the right Assume thatSwitchA and SwitchB are HP Comware switches. For which IP address does the user generate an ARP?

A. The user generates an ARP for the MAC address that corresponds to 10.1.11.1

B. The user generates an ARP for the MAC address that corresponds to 10.1.12.1

C. The user generates an ARP for the MAC address that corresponds to 10.1.12.2

D. The user generates an ARP for the MAC address that corresponds to 10.1.11.11



QUESTION 40

A network administrator enables debug to troubleshoot an OSPF adjacency on an HP Comware switch. Thenetwork administrator then disables and then re-enables an interface connected to another switch runningOSPF. After waiting for a few minutes, no output displays on the console.

Which action must the network administrator take to resolve this problem?

A. Execute the terminal logging command

B. Restart the OSPF process.

C. Re-initialize OSPF on the respective interface.

D. Execute the terminal debugging command.


23/33



QUESTION 41A network administrator wants to redirect log messages on the HP Comware switches to a syslog server.Which configuration implements the desired result?

A.

B.

C.

D.



QUESTION 42An HP Comware switch and HP ProVision switch are connected by using port g1/0/1 on the Comware switchand port A1 on the ProVision switch. The configuration of the two switches is as follows:


24/33

Based on this information, which statement is true?

A. The switches cannot ping each other in VLAN 1 because VLAN 1 has not been added to the Comwaretrunk.

B. The switches cannot ping each other in VLAN 2 or 3 because these VLANs need to be untagged on theProVision switch.

C. The switches cannot ping each other in any VLAN since the trunk mode is not static LACP.

D. The switches can ping each other in VLAN 1.

Correct Answer:A



QUESTION 43A network administrator is setting up OSPF between an HP Provision and HP Comware switch. Once theconfiguration is finished, the network administrator sees log messages in the Comware session about thesuccessful establishment of the adjacency. However, the network administrator does not see similar messageson the Provision console.


25/33

How can the network administrator see these log messages about the new OSPF adjacencies on theProvision console?

A. Use the show event-log command.

B. Use the terminal logging command.

C. Use the terminal monitor command.

D. Use the show logging command.



QUESTION 44Which HP redundancy features are supported by both HP Provision and HP Comware switches? (Select two.)

A. Dynamic LACP meshed stacking

B. Distributed trunking

C. Static link aggregation

D. Static LACP

Correct Answer: CDSection: (none)Explanation


QUESTION 45Identify the port types that can be configured for HP Provision and HP Comware switches.(Options can be used more than once.)

A.




26/33

QUESTION 46Which item is different between the IEEE 802.3z and 802.3ae standards?

A. Link aggregation

B. Frame sizes

C. Support of copper and fiber cabling

D. Duplexing


Explanation/Reference:Explanation:

802.3z 1998 1000BASE-X GigabitEthernet -; 1 /(125 /)802.3ae 2003 10 Gigabit Ethernet 10 /(1,250 /) Ethernet ; 10GBASE-SR, 10GBASE-LR, 10GBASE-ER, 10GBASE-SW, 10GBASE-LW, 10GBASE-EW

QUESTION 47A network administrator attempts to access the console port of an HP Comware switch. The networkadministrator is immediately prompted for a username and password, but cannot remember the correctaccount information. The network administrator then reboots the switch and accesses the ExtendedBootROMmenu, where this information displays:


27/33

Which option can the network administrator choose to get access to User and System Views from the switch'sconsole port?

A. Option 4

B. Option 5

C. Option 6

D. Option 8



QUESTION 48A network administrator is connected to the console of an HP Comware switch when these messages display:

Based on this information, what has just occurred?

A. A 10 GbE line card was inserted into the slot of the Comware switch.

B. Another member has joined the IRF topology.

C. The main processor card on a 7500 switch has become active.

D. The second processor card on a 5820 switch has become active.



QUESTION 49A network administrator receives a new HP Provision switch and notices that the software version running onthe switch is older than what is currently used in the network. The network administrator copies an updatedversion of the operating system from the new switch's USB port to the secondary flash location. The networkadministrator then executes the following command:

ProVision # boot system flash secondary

The switch reboots using the new operating system. However, when the network administrator turns off the


28/33

switch and turns it back on, the switch boots from the old operating system. Which solution should the networkadministrator use to fix the problem?

A. Execute the startup-default secondary command.

B. Execute the boot-loader file command.

C. Execute the boot set-default flash secondary command.

D. Boot into the switch's Monitor ROM Console and perform the upgrade a second time.

E. Execute the startup-boot secondary command



QUESTION 50Refer to the command output.

Based on this output, which statement is true?

A. This router is the BDR.

B. This router is the DR.

C. This router is a DROTHER.

D. This router is not participating in OSPF in VLAN 220.


Explanation/Reference:The correct answer is A. Answer B is incorrect because 10.0.0.21 is the DR. Answer C is incorrect becausethere is a DR and a DROTHER, which means that this router must be the BDR. Answer D is incorrect becausethis router has formed two adjacencies with other OSPF routers in VLAN 220.

QUESTION 51Which HP information management product manages large data volumes, is known for fast queryperformance, and is available on HP DL380 rack-mount servers?

A. HP Moonshot

B. HP StoreAll

C. HP AppSystem for SAP HANA

D. HP Vertica Analytics System



29/33



The network shown in the exhibit is comprised of four MSTP regions that are interconnected Based on thistopology, which statement is true?

A. PVST should be used instead of MSTP

B. A routing solution must be used between MSTP regions when more than one region exists

C. An optimized topology can be created using MSTP between the regions

D. The switches are running the equivalent of RSTP between the regions





30/33

When should the topology shown in the exhibit be implemented in a network?

A. When roaming is not desired

B. When autonomous mode is needed on the APs

C. When a layer 2 switched network is required

D. When centralized management of APs is required



QUESTION 54Which statements are correct about HP StoreOnce Backup? (Select two.)

A. It provides long term data retention using tape backup libraries with LT0-6 technology.

B. It is a modular, branch-in-a-box solution that reduces the cost of remote installations

C. It transfers only unique data across the network and stores it on the remote backup devices.

D. It reduces bandwidth and storage media use with deduplication technology.

E. It provides high-speed data backup using a 3U rack enclosure with multiple tape arrays.


31/33


32/33


33/33

password cipher 12345678quit

B. user-interface aux0authentication-mode schemequit

username administratorpassword cipher 12345678

quitC. user-interface aux0

authentication-mode schemequit

local-user administratorpassword cipher 12345678quit

D. user-interface con0authentication-mode schemequit

username administratorpassword cipher 12345678quit

Correct Answer:Section: (none)Explanation

Explanation/Reference:The correct answer is C. Choice A is incorrect because Comware switches do not have a con0 port and thereis no local-user authentication mode. Choice B is incorrect because there is no username command.Choice D is incorrect because Comware switches do not have a con0 port and there is no usernamecommand.

Documents

HP.actualtests.hp2 Z26.v2014!03!17.by.rose