HP 16 Epoxy Fittings - National Oilwell Varco · 4 HP 16 Epoxy Fittings View of Fitting Illustrations Reducing Tee Reducing Tee(1) - 1"-16" parts are available in Green Thread HP

[email protected] nov.com/fgs

90° Elbow(1) - 1"-16" parts are available in Green Thread HP ONLY

General Notes:1. 2”-16” Green Thread™ HP fittings are be used with both Green Thread HP and Red Thread™ HP piping. Refer to “Chemical Resistance Guide”,

Bulletin No. ENG5615, for chemical recommendations.2. 2”-16” Red Thread HP fittings may be used only on Red Thread HP piping.3. 1”-1½” fittings are available in Green Thread HP products only. All fitting ratings are for 200°F (93°C). Red Thread fittings are serviceable up

to 210°F (98.9°C) by applying a 0.92 de-rating factor. Green Thread fittings are serviceable up to 230°F (110°C) by applying a 0.76 de-rating factor.

Fiber Glass Systems provides a broad range of low pressure fiberglass fittings and accessories to accompany our low pressure line pipe. This allows for a complete corrosion free piping system. All of these fittings are manufactured using the filament winding or molded method of fabrication, using premium glass fibers, and quality epoxy resins. This ensures maximum pressure capabilities of these composite elements.

O I L & G A S C H E M I C A L& I N D U S T R I A L

O F F S H O R EM A R I N E M I N I N GF U E LH A N D L I N G

HP 16 Epoxy Fittings(Filament wound with reinforced epoxy inner liner - Compatible with Red Thread and Green Thread HP 16 piping systems)

View of Fitting Illustrations

90° Elbow

PipeSize A B C D

BoltHole Size # of

BoltsO(3)

X(2)

GT PipeX(2)

RT PipeWeightBxB

WeightBxF

WeightFxF

Steady Pressure

in mm in mm in mm in mm in mm in mm in mm in mm in mm lb kg lb kg lb kg psig bar

1 25 2¾ 70 3½ 89 ¾ 19 3⅛ 79 ⅝ 16 4 4¼ 108 1 25 - - 0.4 0.2 1.0 0.5 1.7 0.8 435 30

1½ 40 3⅜ 86 4 102 ¾ 19 3⅞ 98 ⅝ 16 4 5 127 1⅛ 29 - - 0.6 0.3 1.5 0.7 2.4 1.1 435 30

2 50 3⅜ 86 4½ 114 ¾ 19 4¾ 121 ¾ 19 4 6 152 1⅝ 41 1⅝ 41 1.2 0.5 2.5 1.1 3.6 1.6 435 30

3 80 4⅝ 117 5½ 140 1⅜ 35 6 152 ¾ 19 4 7 ½ 190 1⅞ 48 1¾ 44 2.3 1.0 4.6 2.1 10 4.5 435 30

4 100 5⅛ 130 6½ 165 1⅜ 35 7½ 190 ¾ 19 8 9 229 2 51 1⅝ 41 3.3 1.5 6.4 2.9 15.9 7.2 232 16

6 150 6⅛ 156 8 203 1½ 38 9½ 241 ⅞ 22 8 11 279 2¼ 57 2¼ 57 7.2 3.3 11.8 5.4 15.9 7.2 232 16

8 200 11⅝ 295 9 229 1¾ 44 11¾ 298 ⅞ 22 8 13½ 343 3 76 3⅜ 86 10.9 4.9 15.4 7.0 19.9 9.0 232 16

10 250 13 330 11 279 2 51 14¼ 362 1 25 12 16 406 3¼ 83 3½ 89 14.9 6.8 23.8 10.8 32.8 14.9 232 16

12 300 14 356 12 305 2¼ 57 17 432 1 25 12 19 483 3⅜ 86 3⅞ 98 22.6 10.3 38.3 17.4 54.0 24.5 232 16

14 350 19 483 14 356 2½ 64 18¾ 476 1⅛ 29 12 20¾ 527 5⅜ 137 5½ 140 26.5 12.0 45.0 20.4 65.0 29.5 232 16

16 400 20¼ 514 15 381 2½ 64 21¼ 540 1⅛ 29 16 23¼ 591 5½ 140 5½ 140 45.0 20.4 65.0 29.5 108 49.0 232 16(1) ”A” dimensions shown are for Green Thread HP fittings. 1”-6” fittings are compression molded; 8”-16” fittings are filament wound. 1”-6” filament wound fittings are in CI1370.(2) Nominal make-up dimension for drawing layout work only using non-threaded spigots. Do not use for assembly dimensions.(3) Flanges should be joined to flat-faced flanges. When joining to raised-faced flange connections, consult installation or engineering manuals. Bolt torque, gasket thickness and hardness recommendations are in Manual INS6000.

2 HP 16 Epoxy Fittings


Reducing Tee

45° Elbow(1) - 1"-16" parts are available in Green Thread HP ONLY

PipeSize A B C D

BoltHole Size # of

BoltsO(3)

X(2)

GT PipeX(2)

RT PipeWeightBxB

WeightBxF

WeightFxF

Steady Pressure

in mm in mm in mm in mm in mm in mm in mm in mm in mm lb kg lb kg lb kg psig bar

1 25 2⅜ 60 2 51 ¾ 19 3⅛ 79 ⅝ 16 4 4¼ 108 1 25 - - 0.3 0.14 0.8 0.36 1.4 0.64 435 30

1½ 40 2⅞ 73 2¼ 57 ¾ 19 3⅞ 98 ⅝ 16 4 5 127 1⅛ 29 - - 0.4 0.18 1.2 0.54 2.0 0.91 435 30

2 50 2⅝ 67 2½ 64 ¾ 19 4¾ 121 ¾ 19 4 6 152 1⅝ 41 1⅝ 41 0.9 0.41 1.9 0.86 2.8 1.27 435 30

3 80 3¾ 95 3 76 1⅜ 35 6 152 ¾ 19 4 7½ 190 1⅞ 48 1¾ 44 1.6 0.73 3.5 1.59 7.9 3.58 435 30

4 100 3⅞ 98 4 102 1⅜ 35 7½ 190 ¾ 19 8 9 229 2 51 1⅝ 41 2.4 1.09 5.1 2.31 13.1 5.94 232 16

6 150 4⅜ 111 5 127 1½ 38 9½ 241 ⅞ 22 8 11 279 2¼ 57 2¼ 57 4.8 2.18 8.4 3.81 12.5 5.67 232 16

8 200 8⅛ 206 5½ 140 1¾ 44 11¾ 298 ⅞ 22 8 13½ 343 3 76 3⅜ 86 6.9 3.11 11.9 5.4 16.8 7.62 232 16

10 250 8⅝ 219 6½ 165 2 51 14¼ 362 1 25 12 16 406 3¼ 83 3½ 89 8.9 4.04 18.5 8.39 28.2 12.79 232 16

12 300 9½ 241 7½ 190 2¼ 57 17 432 1 25 12 19 483 3⅜ 86 3⅞ 98 14.0 6.35 32.6 14.8 47.2 21.41 232 16

14 350 12½ 318 7½ 191 2½ 64 18¾ 476 1⅛ 29 12 20¾ 527 5⅜ 137 5½ 140 17.0 7.71 46.0 20.9 73.0 33.11 232 16

16 400 13¼ 337 8 203 2½ 64 21¼ 540 1⅛ 29 16 23¼ 591 5½ 140 5½ 140 25.0 11.3 56.0 25.4 84.0 38.1 232 16(1) ”A” dimensions shown are for GREEN THREAD HP fittings. 1”-6” fittings are compression molded; 8”-16” fittings are filament wound. 1”-6” filament wound fittings are in CI1370.(2) Nominal make-up dimension for drawing layout work only using non-threaded spigots. Do not use for assembly dimensions.(3) Flanges should be joined to flat-faced flanges. When joining to raised-faced flange connections, consult installation or engineering Manuals INS1000 & ENG1000. Bolt torque, gasket thickness and hardness recommendations are in Manual INS1000.

HP 16 Epoxy Fittings 3


Tee(1) - 1"-16" parts are available in Green Thread HP ONLY

PipeSize A B C D

BoltHole Size # of

BoltsO(3)

X(2)

GT PipeX(2)

RT PipeWeight3B

Weight1F

Weight2F

Weight3F

Steady Pressure

in mm in mm in mm in mm in mm in mm in mm in mm in mm lb kg lb kg lb kg lb kg psig bar1 25 2¾ 70 3½ 89 ¾ 19 3⅛ 79 ⅝ 16 4 4¼ 108 1 25 - - 0.5 0.2 1.1 0.5 1.8 0.8 2.5 1.1 435 301½ 40 3⅜ 86 4 102 ¾ 19 3⅞ 98 ⅝ 16 4 5 127 1⅛ 29 - - 0.9 0.4 1.9 0.9 2.8 1.3 3.6 1.6 435 302 50 3⅜ 86 4½ 114 ¾ 19 4¾ 121 ¾ 19 4 6 152 1⅝ 41 1⅝ 41 1.9 0.9 3.1 1.4 4.8 2.2 5.5 2.5 435 303 80 4⅝ 117 5½ 127 1⅜ 35 6 152 ¾ 19 4 7½ 190 1⅞ 48 1¾ 44 3.6 1.6 5.8 2.6 8.0 3.6 14.5 6.6 435 304 100 5⅛ 130 6½ 165 1⅜ 35 7½ 190 ¾ 19 8 9 229 2 51 1⅝ 41 4.9 2.2 8.0 3.6 11.3 5.1 22.7 10.3 232 166 150 6⅛ 156 8 203 1½ 38 9½ 241 ⅞ 22 8 11 279 2¼ 57 2¼ 57 10.1 4.6 14.3 6.5 19.0 8.6 22.3 10.1 232 168 200 11⅝ 295 9 229 1¾ 44 11¾ 298 ⅞ 22 8 13½ 343 3 76 3⅜ 86 16.1 7.3 20.4 9.3 24.6 11.2 28.9 13.1 232 1610 250 13 330 11 279 2 51 14¼ 362 1 25 12 16 406 3¼ 83 3½ 89 26.2 11.9 34.1 15.5 42.0 19.1 49.8 22.6 232 1612 300 14 356 12 305 2¼ 57 17 432 1 25 12 19 483 3⅜ 86 3⅞ 98 31.8 14.4 47.1 21.4 62.5 28.3 77.8 35.3 232 1614 350 19 483 14 356 2½ 64 18¾ 476 1⅛ 29 12 20¾ 527 5⅜ 137 5½ 140 52.0 23.6 75.5 34.2 99.5 45.1 127 57.6 232 1616 400 20¼ 514 15 381 2½ 64 21¼ 540 1⅛ 29 16 23¼ 591 5½ 140 5½ 140 68.0 30.8 107 48.5 135 61.2 170 77.1 232 16(1) ”A” dimensions shown are for Green Thread HP fittings. 1”-6” fittings are compression molded; 8”-16” fittings are filament wound. 1”-6” filament wound fittings are in CI1370.(2) Nominal make-up dimension for drawing layout work only using non-threaded spigots. Do not use for assembly dimensions.(3) Flanges should be joined to flat-faced flanges. When joining to raised-faced flange connections, consult installation or engineering Manuals INS1000 & ENG1000. Bolt torque, gasket thickness and hardness recommendations are in Manual INS1000 are in Manual INS6000.


Tees



Reducing Tee

Reducing Tee(1) - 1"-16" parts are available in Green Thread HP ONLY

PipeSize AT X1 GT Pipe(1) X1 RT Pipe(1) AS X2 GT Pipe(1) X2 RT Pipe(1) Weight

SteadyPressure

in mm in mm in mm in mm in mm in mm in mm lb kg psig bar

8 x 6 200 x 150 11 ⅝ 295 3 76 3 ⅜ 86 10 ¼ 260 2 7/8 73 2 7/8 73 23 10.4 232 16

8 x 4 200 x 100 11 ⅝ 295 3 76 3 ⅜ 86 10 ¼ 260 4 ⅜ 111 4 102 21 9.5 232 16

8 x 3 200 x 80 11 ⅝ 295 3 76 3 ⅜ 86 9 ⅞ 251 3 76 2 7/8 73 20 9.1 232 16

8 x 2 200 x 50 11 ⅝ 295 3 76 3 ⅜ 86 9 13/16 249 1 ½ 38 1 ½ 38 19 8.6 232 16

10 x 8 250 x 200 13 1/16 332 3 ¼ 83 3 ½ 89 13 ⅝ 346 3 76 3 ⅜ 86 39 17.7 232 16

10 x 6 250 x 150 13 1/16 332 3 ¼ 83 3 ½ 89 11 ¾ 298 2 7/8 73 2 7/8 73 36 16.3 232 16

10 x 4 250 x 100 13 1/16 332 3 ¼ 83 3 ½ 89 11 ¾ 298 4 ⅜ 111 4 102 33 14.9 232 16

10 x 3 250 x 80 13 1/16 332 3 ¼ 83 3 ½ 89 11 ⅜ 289 3 76 2 7/8 73 32 14.5 232 16

12 x 10 300 x 250 13 15/16 354 3 ⅜ 86 3 7/8 98 15 1/16 383 3 ¼ 83 3 ½ 89 51 23.1 232 16

12 x 8 300 x 200 13 15/16 354 3 ⅜ 86 3 7/8 98 15 ⅛ 383 3 76 3 ⅜ 86 48 21.8 232 16

12 x 6 300 x 150 13 15/16 354 3 ⅜ 86 3 7/8 98 13 ¼ 337 2 7/8 73 2 7/8 73 45 20.4 232 16

12 x 4 300 x 100 13 15/16 354 3 ⅜ 86 3 7/8 98 13 ¼ 337 4 ⅜ 111 4 101 42 19.1 232 16

14 x 12 350 x 300 19 1/16 484 5 ⅜ 137 5 ½ 140 15 15/16 405 3 ⅜ 86 3 7/8 98 67 30.4 232 16

14 x 10 350 x 250 19 1/16 484 5 ⅜ 137 5 ½ 140 15 9/16 395 3 ¼ 83 3 ½ 89 64 29.0 232 16

14 x 8 350 x 200 19 1/16 484 5 ⅜ 137 5 ½ 140 15 ⅝ 390 3 76 3 ⅜ 86 60 27.2 232 16

14 x 6 350 x 150 19 1/16 484 5 ⅜ 137 5 ½ 140 13 ¾ 349 2 7/8 73 2 7/8 73 57 25.9 232 16

16 x 14 400 x 350 20 ¼ 514 5 ½ 140 5 ½ 140 19 ½ 495 5 ⅜ 137 5 ½ 140 103 46.7 232 16

16 x 12 400 x 300 20 ¼ 514 5 ½ 140 5 ½ 140 16 15/16 430 3 ⅜ 86 3 7/8 98 99 44.9 232 16

16 x 10 400 x 250 20 ¼ 514 5 ½ 140 5 ½ 140 16 ⅝ 422 3 ¼ 83 3 ½ 89 94 42.6 232 16

16 x 8 400 x 200 20 ¼ 514 5 ½ 140 5 ½ 140 16 ⅝ 422 3 76 3 ⅜ 86 90 40.8 232 16(1) Nominal make-up dimension for drawing layout work only using non-threaded spigots. Do not use for assembly dimensions.

5HP 16 Epoxy Fittings


Flanges

PipeSize B C CC D

EBolt Hole Size - # O

X(1)

GT PipeX(1)

RT PipeBolt Torque(2)

ft-lbs

WeightFlange

Wt. Blind Flange

SteadyPressure Rating (psi)

M FW M FW M FW M FW Blind(3)

in in in in in in-no. in in in in in min max lbs lbs lbs psig1 1 3/4 3/4 3/4 3 1/8 5/8 - 4 4 1/4 1 1 - - 20 25 0.6 0.6 0.8 435 435 3001 1/2 1 3/4 3/4 3/4 3 7/8 5/8 - 4 5 1 1 1/8 - - 20 25 0.9 0.9 0.9 435 435 3002 2 1/4 3/4 3/4 4 3/4 3/4 - 4 6 1 ⅝ 1 ⅝ 1 ⅝ 1 ⅝ 25 30 1.3 1.3 1.3 435 435(4) 3003 2 5/8 1 3/8 1 6 3/4 - 4 7 1/2 1 7/8 1 7/8 1 ¾ 1 ¾ 25 30 2.6 3.4 3 435 300(4) 3004 2 5/8 1 3/8 1 7 1/2 3/4 - 8 9 2 2 3/8 1 ⅝ 1 ⅝ 25 30 3.6 4.9 4 232 232(4) 1506 3 1 1/2 1 1/8 9 1/2 7/8 - 8 11 2 ½ 2 ¼ 2 ¼ 2 ¼ 25 30 4.4 6.5 6.6 232 232(4) 1508 4 1 3/4 1 1/8 11 3/4 7/8 - 8 13 1/2 2 3/8 2 1/8 2 7/8 2 ⅝ 80 100 9.3 11 10.6 232 232 13510 4 3/4 2 1 1/4 14 1/4 1 - 12 16 3 7/8 3 1/8 4 1/8 3 3/8 80 100 16 15.8 16.3 232 232 9512 5 2 1/4 1 1/4 17 1 - 12 19 3 7/8 2 7/8 4 3 1/8 80 100 24 25.8 24 232 232 6514 3 1/8 2 1/2 1 7/8 18 3/4 1 1/8 - 12 20 3/4 - 3 - 3 80 100 - 30.7 44.8 - 232 15016 3 1/8 2 1/2 2 1/4 21 1/4 1 1/8 - 16 23 1/4 - 3 - 3 80 100 - 37 67.3 - 232 150

All flanges meet ANSI B16.5 Class 150 Bolt Hole Standards. The following flanges are available as standard parts:

Flanges: 1”-12” Green Thread HP2”-6” Red Thread HP14”-16” Red Thread or Green Thread HP

Compression Molded (M) or Filament Wound (FW)Filament Wound (FW)Filament Wound (FW)

Blind Flanges: 1”-12” Green Thread HP14”-16” Red Thread or Green Thread HP

Compression Molded (M)Contact Molded (M)

Heavy Duty Flange Dimensions

Sizes B Cin in in2 3 2 3/43 3 1/4 34 4 3/4 3 1/26 4 1/4 4

PipeSize B C CC D

EBolt Hole Size - # O

X(1)

GT PipeX(1)

RT PipeBolt Torque(2)

N-m

WeightFlange

Wt. Blind Flange


M FW M FW M FW M FW Blind(3)

mm mm mm mm mm mm mm mm mm mm mm min max kg kg kg bar25 44 19 19 79 16 D - 4 108 25 25 - - 27 34 0.27 0.27 0.36 30 30 20.740 44 19 19 98 16 D - 4 127 25 29 - - 27 34 0.41 0.41 0.41 30 30 20.750 57 19 19 121 19 D - 4 152 41 41 41 41 34 41 0.59 0.59 0.59 30 30(4) 20.780 67 35 25 152 19 D - 4 191 48 48 44 44 34 41 1.18 1.54 1.36 30 21(4) 20.7100 67 35 25 191 19 D - 8 229 51 60 41 41 34 41 1.63 2.22 1.81 16 16(4) 10.3150 76 38 29 241 22 D - 8 279 64 57 57 57 34 41 2.00 2.95 2.99 16 16(4) 10.3200 102 44 29 298 22 D - 8 343 60 54 73 67 41 135 4.22 4.99 4.81 16 16 9.3250 121 51 32 362 25 D - 12 406 98 79 105 86 108 135 7.26 7.17 7.39 16 16 6.5300 127 57 32 432 25 D - 12 483 98 73 102 79 108 135 10.89 11.7 10.89 16 16 4.5350 79 64 48 476 28 D - 12 527 - 76 - 76 108 135 - 13.93 20.32 - 16 10.3400 79 64 57 540 28 D - 16 594 - 76 - 76 108 135 - 16.78 30.53 - 16 10.3(1) Nominal make-up dimension for drawing layout work only using non-threaded spigots. Do not use for assembly dimension.(2) Flanges should be joined to flat-faced flanges. When joining to raised-faced flange connections, consult FGS installation or engineering Manuals INS1000 & ENG1000. Bolt torque, gasket thickness and hardness recommendations are in Manual INS1000.(3) Steel back-up plates must be used to achieve pressure ratings equivalent to the pipe.(4) Heavy duty ANSI 16.5 Class 150 and 300 flanges rated to 450 psig (3.10 MPa) are available. Dimensions are shown in the “Heavy Duty Flange Dimensions” table. The maximum bolt torque for 2”-6” is 100 ft. lbs.


Flange


Orifice Flanges - 2”-8” parts are available inGreen Thread HP ONLY (Note: the 2” orifice flange has only one orifice)

PipeSize B C D

EBolt Hole Size -# of Holes H (NPT) J O

X(2)

GT PipeX(2)

RT Pipe

FlangeBolt Torque(2)

ft-lbs (N-M(2)) Weight


in mm in mm in mm in mm in-no. mm-no. in mm in mm in mm in mm in mm to seal max lbs kg M FW2 50 4¼ 108 2 51 4¾ 121 ¾ - 4 19 - 4 ½ 12.7 1 25 6 152 1⅝ 41 1⅝ 41 25 34 30 41 3.6 1.6 435 303 80 5 127 2 51 6 152 ¾ - 4 19 - 4 ½ 12.7 1 25 7½ 191 1⅞ 48 1⅜ 35 25 34 30 41 5.3 2.4 435 304 100 5 127 2 51 7½ 191 ¾ - 8 19 - 8 ½ 12.7 1 25 9 229 1⅝ 41 2 51 25 34 30 41 6.6 3.0 232 166 150 6 152 2 51 9½ 241 ⅞ - 8 22 - 8 ½ 12.7 1 25 11 279 2¼ 57 2¼ 57 25 34 30 41 8.8 4.0 232 168 200 8¾ 222 2 51 11¾ 298 ⅞ - 8 22 - 8 ½ 12.7 1 25 13½ 343 3⅛ 79 3½ 89 30 41 100 135 14.5 6.6 232 16(1) Nominal make-up dimension for drawing layout work only using non-threaded spigots. Do not use for assembly dimensions.(2) Flanges should be joined to flat-faced flanges. When joining to raised-faced flange connections, consult installation or engineering Manuals INS1000 & ENG1000. Gasket thickness and hardness

recommendations are in Manual INS1000.

Stub EndsNominalPipe Size

PressureRating Bolt Torque A B D X Weight

in mm psi bar ft-lb kg-mm in mm in mm in mm in mm lbs kg2 50 250 17 66 98 2.75 70 0.27 7 3.91 99 2.13 54 0.5 0.223 80 200 14 66 98 2.88 73 0.28 7 5.16 131 2.26 57 0.7 0.314 100 150 10 66 98 2.88 73 0.28 7 6.66 169 2.1 53 1.0 0.456 150 150 10 111 165 3.88 99 0.39 10 8.53 217 3.69 94 2.4 1.08

Flange Rings - ANSI B16.5 Class 150

NominalPipe Size A B E Bolt Hole Size

# of Holes Weight

in mm in mm in mm in mm in mm # lbs kg2 50 2.78 71 0.82 21 6.0 152 3/4 19 4 1.1 0.503 70 3.90 99 1.10 28 7.5 191 3/4 19 4 2.1 0.954 100 4.90 124 1.10 28 9.0 229 3/4 19 8 2.9 1.326 150 7.26 184 1.25 32 11.0 279 7/8 22 8 3.8 1.73

XA

B D

H

E A

B


Stub EndOrfice Flange Flange Rings



Nipples - ANSI B16.5 Class 150

Size Close 4" 6" 8" 10" 12" 16" 24" 36"

in mm GT RT GT RT GT RT GT RT GT RT GT RT GT RT GT RT GT RT1 25 2 ½ - - - X - X - - - - - - - - - - -1 ½ 40 3 ⅛ - - - X - X - - - - - - - - - - -2 50 4 ½ X - X(3) X X X X - X - X - - - - - -3 80 5 ⅛ 5 ⅛ - - X X(4) X X - X - X - - - - - -4 100 5 ⅜ 5 ⅜ - - X X X X - X - X - - - - - -6 150 6 ⅛ 6 ⅛ - - X(4) X(5) X X - X X X - - - - - -8 200 8 ⅝ 9 ⅜ - - - - - - - - X X X X - X - -10 250 9 ⅜ 9 ⅜ - - - - - - - - X X X X - X - X12 300 9 ⅜ 10 ¼ - - - - - - - - X X X X - X - X14 350 - X - - - - - - - - - - X X - X - X16 400 - - - - - - - - - - - - X X - X - XGT - Green Thread, RT - Red Thread, X - Standard available size(3) Actual length 4 ¼”(4) Actual length 6 ¼”(5) Actual length 6 ⅛”

Sleeve Couplings - Green Thread HP

Pipe Size A B X(1) WeightSteady Pressure

in mm in mm in mm lbs kg psig bar1 25 2 ¾ 70 1 ½ 38 1 25 0.1 0.05 435 301 ½ 40 3 ¼ 83 2 52 1 ⅛ 29 0.1 0.05 435 302 50 4 ⅞ 124 2 ⅝ 67 1 ⅝ 41 0.4 0.18 435 303 80 5 127 3 ¾ 95 2 51 0.8 0.36 435 304 100 5 127 4 ¾ 121 2 51 0.9 0.41 232 166 150 7 178 6 ⅞ 175 2 ¼ 57 1.9 0.86 232 168 200 10 254 9 229 3 ⅛ 79 3.4 1.54 232 1610 250 10 ½ 268 11 279 3 ⅛ 79 5.2 2.36 232 1612 300 11 279 13 ⅛ 333 3 ¼ 83 7.5 3.40 232 1614 350 12 ½ 318 15 381 3 ⅞ 98 11.2 5.08 232 1616 400 13 330 17 ⅛ 435 4 ⅛ 105 16.0 7.26 232 16

Sleeve Couplings - Red Thread HP

Pipe Size A B X(1) WeightSteady Pressure

in mm in mm in mm lbs kg psig bar1 25 - - - - - - - - - -1 ½ 40 - - - - - - - - - -2 50 6 152 2 ⅝ 67 1 ⅝ 41 0.40 0.18 435 303 80 6 152 3 ¾ 95 1 ⅞ 48 0.80 0.36 435 304 100 7 178 4 ⅞ 124 2 51 1.40 0.64 435 306 150 8 ⅜ 213 7 ⅛ 181 2 ¾ 70 2.80 1.27 435 308 200 10 254 9 229 2 ⅞ 73 3.30 1.50 232 1610 250 10 ½ 268 11 ⅛ 283 3 ⅜ 86 4.70 2.13 232 1612 300 11 279 13 ⅛ 333 3 ½ 89 6.80 3.08 232 1614 350 12 ½ 318 15 381 4 102 11.2 5.08 232 1616 400 13 330 17 ⅛ 435 4 ⅛ 105 16.0 7.26 232 16


Nipple Sleeve Coupling


Adapter (Bell x Male) - 1” and 1 ½” parts are available in Green Thread ONLY; 2”-8” parts are available in Green Thread or Red Thread HP

Pipe Size A BX(1)

GT PipeX(1)

RT PipeWeightGT

WeightRT

SteadyPressure Rating

in mm in mm in mm in mm in mm lbs kg lbs kg psig bar1 25 3 ½ 89 1 25 1 25 - - 0.1 0.05 - - 435 301 ½ 40 3 ¾ 99 1 ½ 38 1 ⅛ 29 - - 0.3 0.14 - - 435 302 50 4 ¼ 108 2 51 1 ⅝ 41 1 ⅜ 35 0.4 0.18 0.3 0.14 435 303 80 5 ½ 140 3 76 1 ⅞ 48 1 ⅜ 35 0.9 0.41 0.6 0.27 300 20.74 100 5 ½ 140 4 102 2 51 1 ⅝ 41 1.6 0.73 1.0 0.45 232 166 150 6 152 6 152 2 ¼ 57 2 ¼ 57 2.6 1.18 1.8 0.82 232 168 200 9 ¼ 235 8 203 3 ⅛ 79 3 ½ 89 7.2 3.27 6.6 2.99 232 16

Adapter (Spigot x Male) - 1” and 1 ½” parts are available in Green Thread ONLY; 2”-8” parts are available in Green Thread or Red Thread HP

Pipe Size A BX(1)

GT PipeX(1)

RT PipeWeightGT

WeightRT


in mm in mm in mm in mm in mm lbs kg lbs kg psig bar1 25 2 ⅝ 67 1 25 - - - - 0.1 0.05 - - 435 301 ½ 40 2 ¾ 70 1 ¼ 38 - - - - 0.3 0.14 - - 435 302 50 3 ⅝ 92 2 51 - - - - 0.4 0.18 0.3 0.1 435 303 80 4 ⅝ 117 3 76 - - - - 0.9 0.41 0.6 0.2 300 20.74 100 4 ⅞ 124 4 102 - - - - 1.1 0.5 1 0.4 232 166 150 6 ⅞ 175 6 152 - - - - 2.6 1.18 2 0.9 232 168 200 8 203 8 203 - - - - 5.6 2.54 4.9 2.2 232 16

Adapter (Bell x Female) - 1” and 1 ½” parts are available in Green Thread ONLY; 2”-8” parts are available in Green Thread or Red Thread HP

Pipe Size A BX(1)

GT PipeX(1)

RT PipeWeightGT

WeightRT


in mm in mm in mm in mm in mm lbs kg lbs kg psig bar1 25 2 ⅝ 67 - - 1 25 - - 0.1 0.05 - - 435 301 ½ 40 2 ¾ 70 - - 1 ⅛ 29 - - 0.3 0.14 - - 435 302 50 3 ½ 89 - - 1 ⅝ 41 1 ⅜ 35 0.6 0.27 0.3 0.1 435 303 80 4 ½ 114 - - 1 ⅞ 48 1 ⅜ 35 0.6 0.27 0.5 0.2 300 20.74 100 4 ½ 114 - - 2 51 1 ⅝ 41 0.6 0.27 0.5 0.2 232 166 150 5 ½ 140 - - 2 ¼ 57 2 ¼ 57 1.9 0.86 1.3 0.6 232 168 200 7 178 - - 3 ⅛ 79 3 ½ 89 5.1 2.31 3.5 1.6 150 10.3(1) Nominal make-up dimension for drawing layout work only using non-threaded spigots. Do not use for assembly dimensions.


Adapter (Spigot x Male)Adapter (Bell x Male) Adapter (Male x Female)



Adapter (Spigot x Female) - 1” and 1½” parts are available in Green Thread ONLY; 2”-8” parts are available in Green Thread or Red Thread HP; 10” and 12” are available in Red Thread HP

Pipe Size A BX(1)

GT PipeX(1)

RT PipeWeightGT

WeightRT


in mm in mm in mm in mm in mm lbs kg lbs kg psig bar1 25 3 ⅝ 92 1 25 - - - - 0.2 0.09 - - 435 301 ½ 40 4 102 1 ½ 38 - - - - 0.3 0.14 - - 435 302 50 3 ⅞ 98 2 51 - - - - 0.4 0.18 0.3 0.14 435 303 80 4 ¾ 121 3 ⅛ 76 - - - - 0.8 0.36 0.5 0.23 290 20.74 100 4 ⅞ 124 4 ⅛ 102 - - - - 1.0 0.45 0.6 0.27 232 166 150 6 ¾ 171 6 152 - - - - 3.4 1.54 2.6 1.18 232 168 200 10 254 8 203 - - - - 8.0 3.63 7.1 3.22 150 10

Pipe Size A BX(1)

GT PipeX(1)

RT PipeWeightGT

WeightRT


in mm in mm in mm in mm in mm lbs kg lbs kg psig bar1 25 3 ½ 89 ⅞ 22 1 25 - - 0.3 0.14 - - 435 301 ½ 40 3 ⅞ 98 1½ 38 1 ⅛ 29 - - 0.5 0.23 - - 435 302 50 4 ¼ 108 2 51 1 ⅝ 41 1 ⅜ 35 0.5 0.23 0.3 0.14 435 303 80 5 127 3 76 1 ⅞ 48 1 ⅜ 35 0.9 0.41 0.6 0.27 290 20.74 100 5 127 4 102 2 51 1 ⅝ 41 1.0 0.45 0.8 0.63 232 166 150 5 ⅝ 143 6 152 2 ¼ 57 2 ¼ 57 2.3 1.04 1.8 0.84 232 168 200 8 ¼ 210 8 203 3 ⅛ 79 3 ½ 89 5.8 2.63 4.9 2.22 232 1610 250 8 ¼ 210 10 ⅛ 257 - - 3 ¾ 95 - - 6.3 2.86 190 13.1


Adapter - Bell x GroovedAdapter - Spigot x Female

Adapter (Bell x Grooved(2)) - 1” and 1½” parts are available in Green Thread ONLY; 2”-8” parts are available in Green Thread or Red Thread HP; 10” and 12” are available in Red Thread HP

Pipe Size A BX(1)

GT PipeX(1)

RT PipeWeightGT

WeightRT


in mm in mm in mm in mm in mm lbs kg lbs kg psig bar1 25 2 ¾ 70 ⅞ 22 - - - - 0.1 0.05 - - 435 301 ½ 40 3 ⅛ 79 1 ½ 38 - - - - 0.2 0.09 - - 435 302 50 3 ⅝ 92 2 51 - - - - 0.3 0.14 0.3 0.14 435 303 80 4 ¼ 127 3 76 - - - - 0.9 0.41 0.6 0.27 290 204 100 4 ½ 114 4 102 - - - - 1.0 0.45 0.9 0.41 232 166 150 5 127 6 152 - - - - 2.6 1.18 2.0 0.91 232 168 200 7 178 8 203 - - - - 4.4 2 4.1 1.86 232 1610 250 7 178 10 ⅛ 257 - - - - - - 5.6 2.54 190 13.112 300 7 178 12 305 - - - - - - 6.8 3.08 150 10.3(1) Nominal make-up dimension for drawing layout work only using non-threaded spigots. Do not use for assembly dimensions.(2) Compatible with Victaulic® HP70ES couplings.

Adapter (Spigot x Grooved(2)) - 1” and 1½” parts are available in Green Thread ONLY; 2”-8” parts are available in Green Thread or Red Thread HP; 10” and 12” are available in Red Thread HP

Adapter - Spigot x Grooved



Concentric Reducer - Bell x Bell

Concentric Reducer (Bell x Bell) - 1”-16 parts are available in Green Thread ONLY

Pipe Size AX(1)

GT PipeX(1)

GT PipeX(1)

RT PipeX(1)

RT Pipe WeightSteadyPressure Rating

in mm in mm in mm in mm in mm in mm lbs kg psig bar

2 x 1 50 x 25 5 ½ 140 1 ⅝ 41 1 25 1 ⅝ 41 NA NA 0.6 0.27 435 30

2 x 1 ½ 50 x 40 5 127 1 ⅝ 41 1 ⅛ 29 1 ⅝ 41 NA NA 0.6 0.27 435 30

3 x 1 80 x 25 6 ¼ 159 1 ⅞ 48 1 25 1 ⅞ 48 NA NA 1.0 0.45 435 30

3 x 1 ½ 80 x 40 6 ¼ 159 1 ⅞ 48 1 ⅛ 29 1 ¾ 44 NA NA 1.1 0.5 435 30

3 x 2 80 x 50 6 152 1⅞ 48 1 ⅛ 29 1 ⅞ 48 1 ⅝ 41 1.1 0.5 435 30

4 x 1 ½ 100 x 40 7 ⅜ 187 2 51 1 ⅛ 29 1 ⅝ 41 NA NA 1.8 0.82 232 16

4 x 2 100 x 50 8¼ 210 2 51 1 ⅝ 41 1 ⅝ 41 1 ⅝ 41 2.0 0.91 232 16

4 x 3 100 x 80 7 178 2 51 1 ⅞ 48 1 ⅝ 41 1 ⅞ 48 1.7 0.77 232 16

6 x 3 150 x 80 10 ⅞ 276 2 ⅞ 73 1 ⅞ 48 2 ⅞ 73 1 ⅞ 48 4.3 1.95 232 16

6 x 4 150 x 100 9 229 2 ¼ 57 2 51 2 ¼ 57 1 ⅝ 41 3.4 1.54 232 16

8 x 4 200 x 100 14 356 3 76 2 51 3 ⅜ 86 1 ⅝ 41 6.7 3.04 232 16

8 x 6 200 x 150 15 ¼ 387 3 76 2 ⅞ 73 3 ⅜ 86 2 ⅞ 73 7.3 3.31 232 16

10 x 6 250 x 150 15 ¼ 387 3 ¼ 83 2 ⅞ 73 3 ½ 89 2 ⅝ 67 10.5 4.76 232 16

10 x 8 250 x 200 16 ½ 419 3 ¼ 83 3 76 3 ½ 89 3 ⅜ 86 11.1 5.03 232 16

12 x 6 300 x 150 17 ⅛ 435 3 ⅜ 86 2 ⅞ 73 3 ⅞ 98 2 ⅞ 73 18.0 8.16 232 16

12 x 8 300 x 200 18 ⅜ 467 3 ⅜ 86 3 76 3 ⅞ 98 3 ⅜ 86 17.0 7.71 232 16

12 x 10 300 x 250 17 ¾ 451 3 ⅜ 86 3 ¼ 83 3 ⅞ 98 3 ½ 89 16.4 7.44 232 16

14 x 8 350 x 200 23 ½ 597 5 ⅜ 137 3 76 5 ½ 140 3 ⅜ 86 23.0 10.43 232 16

14 x 10 350 x 250 22 ⅞ 581 5 ⅜ 137 3 ¼ 83 5 ½ 140 3 ½ 89 21.9 9.93 232 16

14 x 12 350 x 300 22 ¾ 578 5 ⅜ 137 3 ⅜ 86 5 ½ 140 3 ⅞ 98 21.8 9.89 232 16

16 x 10 400 x 250 25 ⅛ 638 5 1/2 140 3 ¼ 83 5 1/2 140 3 ½ 89 28.0 12.7 232 16

16 x 12 400 x 300 25 635 5 1/2 140 3 ⅜ 86 5 1/2 140 3 ⅞ 98 27.7 12.56 232 16

16 x 14 400 x 350 28 711 5 1/2 140 5 3/8 137 5 1/2 140 5 3/8 137 31.1 14.11 232 16

NOTE: MULTI-STEP reducers are available through 16” sizes. Information is available on request.(1) Nominal make-up dimension for drawing layout work only using non-threaded spigots. Do not use for assembly dimensions.(2) Flanges should be joined to flat-faced flanges. When joining to raised-faced flange connections, consult installation or engineering manuals. Bolt torque, gasket thickness and hardness

recommendations are in manual INS1000. These comments also apply to the flanged concentric reducers on the following page.



Concentric Reducer - Flanged


Concentric Reducer (Flanged(2)) - 1”-16 parts are available in Green Thread ONLY

PipeSize B C D

EBolt Hole Size -# of Holes O G H

JBolt Hole Size - # of Holes P Weight

Steady Pressure Rating

in mm in mm in mm in mm in mm in mm in mm in mm in mm in mm lbs kg psig bar

2x1 50x25 5 127 ¾ 19 4 ¾ 121 ¾ - 4 19 - 4 6 152 ¾ 19 3 ⅞ 98 ⅝ - 4 16 - 4 4 ¼ 108 2.6 1.18 300 20.7

2x1½ 50x40 5 127 ¾ 19 4 ¾ 121 ¾ - 4 19 - 4 6 152 ¾ 19 3 ⅞ 98 ⅝ - 4 16 - 4 5 127 2.6 1.18 300 20.7

3x1½ 80x40 6 152 1 ⅜ 35 6 152 ¾ - 4 19 - 4 7 ½ 191 ¾ 19 4 ¾ 121 ¾ - 4 19 - 4 5 127 4.4 2.00 190 13.1

3x2 80x50 6 152 1 ⅜ 35 6 152 ¾ - 4 19 - 4 7 ½ 191 ¾ 19 4 ¾ 121 ¾ - 4 19 - 4 6 152 4.4 2.00 190 13.1

4x2 100x50 7 178 1 ⅜ 35 7 ½ 191 ¾ - 8 19 - 8 9 229 1 ⅜ 35 6 152 ¾ - 4 19 - 4 6 152 7.1 3.22 150 10.3

4x3 100x80 7 178 1 ⅜ 35 7 ½ 191 ¾ - 8 19 - 8 9 229 1 ⅜ 35 6 152 ¾ - 4 19 - 4 7 ½ 191 7.1 3.22 150 10.3

6x3 150x80 9 229 1 ½ 38 9 ½ 241 ⅞ - 8 22 - 8 11 279 1 ⅜ 35 7 ½ 191 ¾ - 8 19 - 8 7 ½ 191 11.0 4.99 150 10.3

6x4 150x100 9 229 1 ½ 38 9 ½ 241 ⅞ - 8 22 - 8 11 279 1 ⅜ 35 7 ½ 191 ¾ - 8 19 - 8 9 229 11.0 4.99 150 10.3

8x4 200x100 11 279 1 ¾ 44 11 ¾ 298 ⅞ - 8 22 - 8 13 ½ 343 1 ½ 38 9 ½ 241 ⅞ - 8 22 - 8 9 229 17.6 7.98 232 16.0

8x6 200x150 11 279 1 ¾ 44 11 ¾ 298 ⅞ - 8 22 - 8 13 ½ 343 1 ½ 38 9 ½ 241 ⅞ - 8 22 - 8 11 279 17.6 7.98 232 16.0

10x6 250x150 12 305 2 51 14 ¼ 362 1 - 12 25 - 12 16 406 1 ¾ 44 11 ¾ 298 ⅞ - 8 22 - 8 11 279 28.2 12.79 232 16.0

10x8 250x200 12 305 2 51 14 ¼ 362 1 - 12 25 - 12 16 406 1 ¾ 44 11 ¾ 298 ⅞ - 8 22 - 8 13 ½ 343 28.2 12.79 232 16.0

12x8 300x200 14 356 2 ¼ 57 17 432 1 - 12 25 - 12 19 483 2 51 14 ¼ 362 1 - 12 25 - 12 13 ½ 343 43.0 19.50 232 16.0

12x10 300x250 14 356 2 ¼ 57 17 432 1 - 12 25 - 12 19 483 2 51 14 ¼ 362 1 - 12 25 - 12 16 406 43.0 19.50 232 16.0

14x10 350x250 16 406 2 ½ 64 18 ¾ 476 1 ⅛ - 12 29 - 12 20 ¾ 527 2 ¼ 57 17 432 1 - 12 25 - 12 16 406 55.0 24.95 232 16.0

14x12 350x300 16 406 2 ½ 64 18 ¾ 476 1 ⅛ - 12 29 - 12 20 ¾ 527 2 ¼ 57 17 432 1 - 12 25 - 12 19 483 55.0 24.95 232 16.0

16x12 400x305 18 457 2 ½ 64 21 ¼ 540 1 ⅛ - 16 29 - 16 23 ¼ 591 2 ½ 64 18 ¾ 476 1⅛ - 12 29 - 12 19 483 89.5 40.60 232 16.0

16x14 400x350 18 457 2 ½ 64 21 ¼ 540 1 ⅛ - 16 29 - 16 23 ¼ 591 2 ½ 64 18 ¾ 476 1⅛ - 12 29 - 12 20 ¾ 527 89.5 40.60 232 16.0



Concentric Reducer - Bell x Bell

Eccentric Reducer (Bell x Bell) - 1”-16 parts are available in Green Thread ONLY

Pipe Size AX(1)

GT PipeX(1)

GT PipeX(1)

RT PipeX(1)



2 x 1 50 x 25 5 ½ 140 1 ⅝ 41 1 25 1 ⅝ 41 NA NA 0.6 0.27 435 30

2 x 1 ½ 50 x 40 5 127 1 ⅝ 41 1 ⅛ 29 1 ⅝ 41 NA NA 0.6 0.27 435 30

3 x 1 80 x 25 6 ¼ 159 1 ⅞ 48 1 25 1 ⅞ 48 NA NA 1.0 0.45 435 30

3 x 1 ½ 80 x 40 6 ¼ 159 1 ⅞ 48 1 ⅛ 29 1 ¾ 44 NA NA 1.1 0.5 435 30

3 x 2 80 x 50 6 152 1⅞ 48 1 ⅛ 29 1 ⅞ 48 1 ⅝ 41 1.1 0.5 435 30

4 x 1 ½ 100 x 40 7 ⅜ 187 2 51 1 ⅛ 29 1 ⅝ 41 NA NA 1.8 0.82 232 16

4 x 2 100 x 50 8¼ 210 2 51 1 ⅝ 41 1 ⅝ 41 1 ⅝ 41 2.0 0.91 232 16

4 x 3 100 x 80 7 178 2 51 1 ⅞ 48 1 ⅝ 41 1 ⅞ 48 1.7 0.77 232 16

6 x 3 150 x 80 10 ⅞ 276 2 ⅞ 73 1 ⅞ 48 2 ⅞ 73 1 ⅞ 48 4.3 1.95 232 16

6 x 4 150 x 100 9 229 2 ¼ 57 2 51 2 ¼ 57 1 ⅝ 41 3.4 1.54 232 16

8 x 4 200 x 100 14 356 3 76 2 51 3 ⅜ 86 1 ⅝ 41 6.7 3.04 232 16

8 x 6 200 x 150 15 ¼ 387 3 76 2 ⅞ 73 3 ⅜ 86 2 ⅞ 73 7.3 3.31 232 16

10 x 6 250 x 150 15 ¼ 387 3 ¼ 83 2 ⅞ 73 3 ½ 89 2 ⅝ 67 10.5 4.76 232 16

10 x 8 250 x 200 16 ½ 419 3 ¼ 83 3 76 3 ½ 89 3 ⅜ 86 11.1 5.03 232 16

12 x 6 300 x 150 17 ⅛ 435 3 ⅜ 86 2 ⅞ 73 3 ⅞ 98 2 ⅞ 73 18.0 8.16 232 16

12 x 8 300 x 200 18 ⅜ 467 3 ⅜ 86 3 76 3 ⅞ 98 3 ⅜ 86 17.0 7.71 232 16

12 x 10 300 x 250 17 ¾ 451 3 ⅜ 86 3 ¼ 83 3 ⅞ 98 3 ½ 89 16.4 7.44 232 16

14 x 8 350 x 200 23 ½ 597 5 ⅜ 137 3 76 5 ½ 140 3 ⅜ 86 23.0 10.43 232 16

14 x 10 350 x 250 22 ⅞ 581 5 ⅜ 137 3 ¼ 83 5 ½ 140 3 ½ 89 21.9 9.93 232 16

14 x 12 350 x 300 22 ¾ 578 5 ⅜ 137 3 ⅜ 86 5 ½ 140 3 ⅞ 98 21.8 9.89 232 16

16 x 10 400 x 250 25 ⅛ 638 5 1/2 140 3 ¼ 83 5 1/2 140 3 ½ 89 28.0 12.7 232 16

16 x 12 400 x 300 25 635 5 1/2 140 3 ⅜ 86 5 1/2 140 3 ⅞ 98 27.7 12.56 232 16

16 x 14 400 x 350 28 711 5 1/2 140 5 3/8 137 5 1/2 140 5 3/8 137 31.1 14.11 232 16

NOTE: MULTI-STEP reducers are available through 16” sizes. Information is available on request.(1) Nominal make-up dimension for drawing layout work only using non-threaded spigots. Do not use for assembly dimensions.(2) Flanges should be joined to flat-faced flanges. When joining to raised-faced flange connections, consult installation or engineering manuals. Bolt torque, gasket thickness and hardness

recommendations are in manual INS1000. These comments also apply to the flanged concentric reducers on the following page.

X1

A

X2



Eccentric Reducer - Flanged


Eccentric Reducer (Flanged(2)) - 1”-16 parts are available in Green Thread ONLY

PipeSize B C D

EBolt Hole Size -# of Holes O G H

JBolt Hole Size - # of Holes P Weight

Steady Pressure Rating

in mm in mm in mm in mm in mm in mm in mm in mm in mm in mm lbs kg psig bar

2x1 50x25 5 127 ¾ 19 4 ¾ 121 ¾ - 4 19 - 4 6 152 ¾ 19 3 ⅞ 98 ⅝ - 4 16 - 4 4 ¼ 108 2.6 1.18 300 20.7

2x1½ 50x40 5 127 ¾ 19 4 ¾ 121 ¾ - 4 19 - 4 6 152 ¾ 19 3 ⅞ 98 ⅝ - 4 16 - 4 5 127 2.6 1.18 300 20.7

3x1 80x25 6 375 1 ⅜ 35 6 152 ¾ - 4 19 - 4 7 ½ 191 ¾ 19 4 ¾ 121 ¾ - 4 19 - 4 5 127 4.4 2.00 190 13

3x1½ 80x40 6 152 1 ⅜ 35 6 152 ¾ - 4 19 - 4 7 ½ 191 ¾ 19 4 ¾ 121 ¾ - 4 19 - 4 5 127 4.4 2.00 190 13.1

3x2 80x50 6 152 1 ⅜ 35 6 152 ¾ - 4 19 - 4 7 ½ 191 ¾ 19 4 ¾ 121 ¾ - 4 19 - 4 6 152 4.4 2.00 190 13.1

4x1½ 100x40 7 391 1 ⅜ 35 7 ½ 191 ¾ - 8 19 - 8 9 229 1 ⅜ 35 6 152 ¾ - 4 19 - 4 6 152 7.1 3.20 150 10

4x2 100x50 7 178 1 ⅜ 35 7 ½ 191 ¾ - 8 19 - 8 9 229 1 ⅜ 35 6 152 ¾ - 4 19 - 4 6 152 7.1 3.22 150 10.3

4x3 100x80 7 178 1 ⅜ 35 7 ½ 191 ¾ - 8 19 - 8 9 229 1 ⅜ 35 6 152 ¾ - 4 19 - 4 7 ½ 191 7.1 3.22 150 10.3

6x3 150x80 9 229 1 ½ 38 9 ½ 241 ⅞ - 8 22 - 8 11 279 1 ⅜ 35 7 ½ 191 ¾ - 8 19 - 8 7 ½ 191 11 4.99 150 10.3

6x4 150x100 9 229 1 ½ 38 9 ½ 241 ⅞ - 8 22 - 8 11 279 1 ⅜ 35 7 ½ 191 ¾ - 8 19 - 8 9 229 11 4.99 150 10.3

8x4 200x100 11 279 1 ¾ 44 11 ¾ 298 ⅞ - 8 22 - 8 13 ½ 343 1 ½ 38 9 ½ 241 ⅞ - 8 22 - 8 9 229 17.6 7.98 232 16

8x6 200x150 11 279 1 ¾ 44 11 ¾ 298 ⅞ - 8 22 - 8 13 ½ 343 1 ½ 38 9 ½ 241 ⅞ - 8 22 - 8 11 279 17.6 7.98 232 16

10x6 250x150 12 305 2 51 14 ¼ 362 1 - 12 25 - 12 16 406 1 ¾ 44 11 ¾ 298 ⅞ - 8 22 - 8 11 279 28.2 12.79 232 16

10x8 250x200 12 305 2 51 14 ¼ 362 1 - 12 25 - 12 16 406 1 ¾ 44 11 ¾ 298 ⅞ - 8 22 - 8 13 ½ 343 28.2 12.79 232 16

12x8 300x200 14 356 2 ¼ 57 17 432 1 - 12 25 - 12 19 483 2 51 14 ¼ 362 1 - 12 25 - 12 13 ½ 343 43.0 19.50 232 16

12x10 300x250 14 356 2 ¼ 57 17 432 1 - 12 25 - 12 19 483 2 51 14 ¼ 362 1 - 12 25 - 12 16 406 43.0 19.50 232 16

14x10 350x250 16 406 2 ½ 64 18 ¾ 476 1 ⅛ - 12 29 - 12 20 ¾ 527 2 ¼ 57 17 432 1 - 12 25 - 12 16 406 55.0 24.95 232 16

14x12 350x300 16 406 2 ½ 64 18 ¾ 476 1 ⅛ - 12 29 - 12 20 ¾ 527 2 ¼ 57 17 432 1 - 12 25 - 12 19 483 55.0 24.95 232 16

16x12 400x305 18 457 2 ½ 64 21 ¼ 540 1 ⅛ - 16 29 - 16 23 ¼ 591 2 ½ 64 18 ¾ 476 1⅛ - 12 29 - 12 19 483 89.5 40.60 232 16

16x14 406x350 18 457 2 ½ 64 21 ¼ 540 1 ⅛ - 16 29 - 16 23 ¼ 591 2 ½ 64 18 ¾ 476 1⅛ - 12 29 - 12 20 ¾ 527 89.5 40.60 232 16

O D

C EG

A

J

H P



Reducer Bushing

Reducer Bushing

Pipe Size AX(1)

GT PipeX(1)


in mm in mm in mm in mm lbs kg psig bar

* * 1 ⅛ 29 - - - - 0.1 0.05 435 30

** ** 1 ⅜ 35 1 25 - - 0.1 0.05 435 30

2 x 1 50 x 25 2 ¼ 57 1 25 - - 0.4 0.18 435 30

2 x 1 NPT 50 x 25 1 ¾ 44 - - - - 0.4 0.18 435 30

2 x 1¼ NPT 50 x 30 1 ¾ 44 - - - - 0.4 0.18 435 30

2 x 1 ½ 50 x 40 2 51 1 ⅛ 29 - - 0.1 0.05 435 30

2 x 1 ½ NPT 50 x 40 1 ¾ 44 - - - - 0.1 0.05 435 30

3 x 2 80 x 50 2 ¼ 57 1 ⅝ 41 1 ⅝ 41 0.8 0.36 435 30

4 x 3 100 x 80 2 ⅝ 67 1 ⅞ 48 1 ⅜ 35 1.0 0.45 232 16

6 x 4 150 x 100 3 ⅛ 79 2 51 1 ½ 38 3.9 1.77 232 16

8 x 6 200 x 150 3 ¼ 83 3 76 2 ⅜ 60 6.8 3.08 232 16

10 x 8 250 x 200 4 102 2 ⅝ 67 3 76 9.9 4.49 232 16

12 x 10 300 x 250 4 ½ 114 3 76 3 ¼ 83 11.8 5.35 232 16

14 x 12 350 x 300 5 ½ 140 3 ⅞ 98 4 ⅛ 105 20.2 9.16 232 16

16 x 14 400 x 350 6 152 4 ½ 114 4 ½ 114 28.9 13.11 232 16

* 1x ¼ NPT, 1x ½ NPT, 1x ¾ NPT, 1 ½x ½ NPT, 1 ½x ¾ NPT**1 ½x1NPT, 1 ½x1(X-GT), 1 ½x1 ¼ NPTNOTE: MULTI-STEP and ECCENTRIC reducers are available through 16” sizes. Information available on request.(1) Nominal make-up dimension for drawing layout work only using non-threaded spigots. Do not use for assembly dimensions.



45° Lateral Flanged45° Lateral Belled


Lateral (45° Lateral Belled)

Pipe Size A FX(1)

GT PipeX(1)


in mm in mm in mm in mm in mm lbs kg psig bar

1 25 3 ⅞ 98 2 ½ 64 1 25 - - 0.6 0.27 150 10.3

1 ½ 40 5 ¼ 133 3 ¼ 83 1 25 - - 1.3 0.59 150 10.3

2 50 7 3/4 197 4 1/4 108 2 1/2 62 2 5/8 67 5.3 2.42 150 10.3

3 80 7 3/4 197 4 1/4 108 2 1/2 62 2 5/8 67 6.2 2.82 150 10.3

4 100 9 229 4 3/8 111 3 76 3 1/4 81 8.5 3.86 150 10.3

6 150 12 1/2 318 5 3/4 146 2 3/4 69 3 74 12.5 5.68 135 9.3

8 200 16 1/4 413 7 3/8 187 3 76 3 3/8 86 36.0 16.36 135 9.3

10 250 19 5/8 498 8 3/4 222 3 1/4 83 3 1/2 89 57.0 25.91 120 8.3

12 300 24 3/4 629 11 3/4 298 3 3/8 86 3 7/8 98 85.0 38.64 90 6.2

14 350 32 ½ 826 15 ¾ 400 3 ⅞ 98 4 102 154.2 69.94 75 5.2

16 400 35 ¾ 908 17 ¾ 451 4 ⅛ 105 4 ⅛ 105 222.6 101.00 75 5.2

Lateral (45° Lateral Flanged(2))

Pipe Size B C D

EBolt HoleSize # of

HolesF O Weight


in mm in mm in mm in mm in mm in mm in mm lbs kg psig bar

1 25 6 152 ¾ 19 3 ¼ 83 ⅝ 16 4 4 ½ 114 4 ¼ 108 2.8 1.27 150 10.3

1 ½ 40 8 ½ 216 ¾ 19 3 ⅞ 98 ⅝ 16 4 5 ½ 140 5 127 4.4 2.00 150 10.3

2 50 8 ⅞ 225 ¾ 19 4 ¾ 121 ¾ 19 4 6 ⅜ 162 6 152 7.8 3.54 150 10.3

3 80 11 ¾ 298 1 ⅜ 35 6 152 ¾ 19 4 8 203 7 ½ 191 13.4 6.08 150 10.3

4 100 12 ⅞ 327 1 ⅜ 35 7 ½ 191 ¾ 19 8 8 ½ 216 9 229 19.2 8.71 150 10.3

6 150 18 457 1 ½ 38 9 ½ 241 ⅞ 22 8 11 279 11 279 35.0 15.90 135 9.3

8 200 21 ¾ 552 1 ¾ 44 11 ¾ 298 ⅞ 22 8 13 ¾ 349 13 ½ 343 65.3 29.60 135 9.3

10 250 26 ⅝ 676 2 51 14 ¼ 362 1 25 12 16 ⅝ 422 16 406 112.0 50.80 120 8.3

12 300 32 813 2 ¼ 57 17 432 1 25 12 20 508 19 483 172.0 78.00 90 6.2

14 350 36 914 2 ½ 64 18 ¾ 476 1⅛ 29 12 22 559 20 ¾ 527 209.0 94.60 75 5.2

16 400 40 1,016 2 ½ 64 21 ¼ 540 1⅛ 29 16 24 610 23 ¼ 594 267.0 121.0 75 5.2(1) Nominal make-up dimension for drawing layout work only using non-threaded spigots. Do not use for assembly dimensions.(2) Flanges should be joined to flat-faced flanges. When joining to raised-faced flange connections, consult installation or engineering Manuals INS1000 & ENG1000. Bolt torque, gasket thickness and

hardness recommendations are in Manual INS1000.



Cross - FlangedCross - Belled

Cross (Belled)

Pipe Size AX(1)

GT PipeX(1)



1 25 2 ¾ 70 1 25 - - 1.4 0.64 300 20.7

1 ½ 40 3 ⅜ 86 1 ⅛ 29 - - 2.0 0.91 300 20.7

2 50 3 ⅜ 86 1 ⅝ 41 1 ½ 38 3.4 1.54 300 20.7

3 80 4 ⅝ 117 1 ⅞ 48 1 ¾ 44 8.5 3.86 190 13.1

4 100 5 ⅛ 130 2 51 1 ⅝ 41 10.7 4.85 150 10.3

6 150 6 ⅛ 156 2 ¼ 57 2 ¼ 57 17.3 7.85 150 10.3

8 200 11 ⅝ 295 3 ⅛ 79 3 ½ 89 30.8 13.97 150 10.3

10 250 13 ⅛ 333 3 ¼ 83 3 ½ 89 42.7 19.37 150 10.3

12 300 14 356 3 ⅜ 86 3 ⅞ 98 73.2 33.2 150 10.3

14 350 16 406 3 ⅞ 98 4 102 104.0 47.27 150 10.3

16 400 17 ¼ 438 4 ⅛ 105 4 ⅛ 105 143.0 64.86 150 10.3

Cross (Flanged(2))

Pipe Size B C D

EBolt HoleSize # of

HolesO Weight



1 25 3 ½ 89 ¾ 19 3 ⅛ 79 ⅝ 16 4 4 ¼ 108 3.8 1.7 300 20.7

1 ½ 40 4 102 ¾ 19 3 ⅛ 79 ⅝ 16 4 5 127 5.4 2.5 300 20.7

2 50 4 ½ 114 ¾ 19 4 ¾ 121 ¾ 19 4 6 152 8.6 3.9 300 20.7

3 80 5 ½ 140 1 ⅜ 35 6 152 ¾ 19 4 7 ½ 191 15.1 6.8 190 13.1

4 100 6 ½ 165 1 ⅜ 35 7 ½ 191 ¾ 19 8 9 229 22.8 10.3 150 10.3

6 150 8 203 1 ½ 38 9 ½ 241 ⅞ 22 8 11 279 34.9 15.8 150 10.3

8 200 9 229 1 ¾ 44 11 ¾ 298 ⅞ 22 8 13 ½ 343 61.2 27.8 150 10.3

10 250 11 279 2 51 14 ¼ 362 1 25 12 16 406 83.5 37.9 150 10.3

12 300 12 305 2 ¼ 57 17 432 1 25 12 19 483 145.0 65.8 150 10.3

14 350 14 356 2 ½ 64 18 ¾ 476 1 ⅛ 29 12 20 ¾ 527 224.0 102.0 150 10.3

16 400 15 381 2 ½ 64 21 ¼ 540 1 ⅛ 29 16 23 ¼ 594 303.0 137.0 150 10.3(1) Nominal make-up dimension for drawing layout work only using non-threaded spigots. Do not use for assembly dimensions.(2) Flanges should be joined only to flat-faced flanges. When joining to raised-faced flange connections, consult installation or engineering Manuals INS1000 & ENG1000. Bolt torque, gasket thickness and

hardness recommendations are in Manual INS1000.



Saddle - Belled Side Outlet


Saddle (Belled Side Outlet) - Parts are available in Green Thread HP ONLY

Pipe Size A B CAngle

X(1)

GT PipeX(1)


in mm in mm in mm in mm in mm lbs kg psig bar2 x 1 50 x 25 2 ⅞ 73 4 102 180 1 25 - - 0.6 0.27 435 302 x 1 ½ 50 x 40 2 ⅞ 73 4 102 180 1 ⅛ 29 - - 0.5 0.23 232 163 x 1 80 x 25 3 ½ 89 6 152 180 1 25 - - 1.5 0.68 300 20.73 x 1 ½ 80 x 40 3 ½ 89 6 152 180 1 ⅛ 29 - - 0.9 0.41 232 163 x 2 80 x 50 4 102 6 152 180 1 ⅝ 41 1 ⅝ 41 1.4 0.64 232 164 x 1 100 x 25 4 102 6 152 180 1 25 - - 1.4 0.64 232 164 x 1 ½ 100 x 40 4 102 6 152 180 1 ⅛ 29 - - 1.5 0.68 232 164 x 2 100 x 50 4 ½ 114 6 152 180 1 ⅝ 41 1 ⅝ 41 1.5 0.68 232 164 x 3 100 x 80 5 ¼ 133 6 152 180 1 ⅞ 48 1 ¾ 44 1.6 0.73 200 13.86 x 1 150 x 25 5 127 6 152 120 1 25 - - 1.4 0.64 232 166 x 1 ½ 150 x 40 5 127 6 152 120 1 ⅛ 29 - - 1.3 0.59 232 166 x 2 150 x 50 5 ½ 140 6 152 120 1 ⅝ 41 1 ⅝ 41 1.5 0.68 232 166 x 3 150 x 80 6 ¼ 159 6 152 120 1 ⅞ 48 1 ¾ 44 1.6 0.73 150 10.36 x 4 150 x 100 6 ⅜ 162 8 203 140 2 51 1 ⅝ 41 2.4 1.09 125 8.68 x 1(2) 200 x 25 7 ⅛ 181 9 229 120 1 25 - - 3.1 1.41 232 168 x 1 ½(2) 200 x 40 7 ⅛ 181 9 229 120 1 ⅛ 29 - - 2.8 1.27 232 168 x 2 200 x 50 7 178 9 229 180 1 ⅝ 41 1 ⅝ 41 2.7 1.22 232 1610 x 1(2) 250 x 25 8 ⅛ 206 9 229 95 1 25 - - 3.1 1.41 232 1610 x 1 ½(2) 250 x 40 8 ⅛ 206 9 229 95 1 ⅛ 29 - - 2.8 1.27 232 1610 x 2 250 x 50 8 203 9 229 180 1 ⅝ 41 1 ⅝ 41 2.7 1.22 232 1610 x 3 250 x 80 9 229 14 356 150 1 ⅞ 48 1 ¾ 44 6.1 2.77 232 1612 x 1(2) 300 x 25 9 ⅛ 232 10 254 90 1 25 - - 3.6 1.63 232 1612 x 1 ½(2) 300 x 40 9 ⅛ 232 10 254 90 1 ⅛ 29 - - 3.3 1.50 232 1612 x 2 300 x 50 9 229 10 254 180 1 ⅝ 41 1 ⅝ 41 3.2 1.45 232 1612 x 3 300 x 80 10 254 14 356 125 1 ⅞ 48 1 ¾ 44 6.1 2.77 232 1612 x 4 300 x 100 9 ⅜ 238 17 432 155 2 51 1 ⅝ 41 8.6 3.90 232 1614 x 1(2) 350 x 25 10 254 12 305 95 1 25 - - 4.7 2.13 232 1614 x 1 ½(2) 350 x 40 10 254 12 305 95 1 ⅛ 29 - - 4.4 2.00 232 1614 x 2 350 x 50 10 254 12 305 95 1 ⅝ 41 1 ⅜ 35 4.3 1.95 232 1614 x 3 350 x 80 10 ⅞ 276 15 381 120 1 ⅞ 48 1 ¾ 44 6.9 3.13 232 1614 x 4 350 x 100 10 ¼ 260 17 432 135 2 51 1 ⅝ 41 8.4 3.81 232 1616 x 1(2) 400 x 25 11 279 13 330 90 1 25 - - 5.4 2.45 232 1616 x 1 ½(2) 400 x 40 11 279 13 330 90 1 ⅛ 29 - - 5.1 2.31 232 1616 x 2 400 x 50 11 279 13 330 90 1 ⅝ 41 1 ⅜ 35 5.0 2.27 232 1616 x 3 400 x 80 11 ⅞ 302 15 381 105 1 ⅞ 48 1 ¾ 44 6.9 3.13 232 1616 x 4 400 x 100 11 ¼ 286 17 432 120 2 51 1 ⅝ 41 8.6 3.90 232 16(1) Nominal make-up dimension for drawing layout work only using non-threaded spigots. Do not use for assembly dimensions.(2) Saddle is manufactured by bonding a reducer bushing into a saddle with a 2” outlet.



Threaded Side Outlet NPT Internal Threads

Threaded Side Outlet NPT Internal Threads

Pipe Size A B CAngle

WeightSteadyPressure Rating

in mm in mm in mm lbs kg psig bar2 x 1 50 x 25 2 ⅞ 73 4 180 102 0.6 0.27 435 302 x 1 ¼ 50 x 30 2 ⅞ 73 4 180 102 0.6 0.27 232 162 x 1 ½ 50 x 40 2 ⅞ 73 4 180 102 0.5 0.23 232 163 x 1 80 x 25 3 ½ 89 6 180 152 1.1 0.50 300 20.73 x 1 ¼ 80 x 30 3 ½ 89 6 180 152 1.0 0.45 232 163 x 1 ½ 80 x 40 3 ½ 89 6 180 152 1.0 0.45 232 164 x 1 100 x 25 4 102 6 180 152 1.6 0.73 232 164 x 1 ¼ 100 x 30 4 102 6 180 152 1.5 0.68 232 164 x 1 ½ 100 x 40 4 102 6 180 152 1.4 0.64 232 166 x 1 150 x 25 5 127 6 120 152 1.5 0.68 232 166 x 1 ¼ 150 x 30 5 127 6 120 152 1.4 0.64 232 166 x 1 ½ 150 x 40 5 127 6 120 152 1.5 0.68 232 168 x 1 200 x 25 7 ⅛ 181 9 120 229 3.1 1.41 232 1610 x 1 250 x 25 8 ⅛ 206 9 95 229 3.1 1.41 232 1612 x 1 300 x 25 9 ⅛ 232 10 90 254 3.6 1.63 232 1614 x 1 350 x 25 10 254 12 95 305 4.7 2.13 232 1616 x 1 400 x 25 11 279 13 90 330 5.4 2.45 232 16

Green Thread HP 16 Branch TableHeader Diameter Branch Diameter

in mm 1 25 1.5 40 2 50 3 80 4 100 6 150 8 200 10 250 12 300 14 250 16 4001 25 T - - - - - - - - - -1.5 40 RBT T - - - - - - - - -2 50 S S/RBT T - - - - - - - -3 80 S S/RBT S/RBT T - - - - - - -4 100 S S S/RBT S*/RBT T - - - - - -6 150 S S S S*/RBT S*/RBT T - - - - -8 200 S S S/T T T T T - - - -10 250 S S S/T S/T T T T T - - -12 300 S S S/T S/T S/T T T T T - -14 250 S S S S/T S/T T T T T T -16 400 S S S S/T S/T T T T T T TS - Saddle, T - Tee, S/T - Tee or Saddle, S/RBT - Saddle or compression molded Tee with Reducer Bushing.

Notes: 1. In general, saddles are limited to branch sizes that are 1/3 of the header size or smaller. 2. Saddles are limited to outlet size of 6 inch or less. 3. Saddles are rated the same as Tees unless otherwise noted by *.



End Cap - 6"-16End Cap - 1"-4"


End Caps - Parts are available in Green Thread HP ONLY

Pipe Size AX(1)

GT PipeX(1)



1 25 2 ¾ 70 1 25 - - 0.3 0.14 435 30

1 ½ 40 2 ⅝ 67 1 ⅛ 29 - - 0.6 0.27 435 30

2 50 2 ¾ 70 1 ⅝ 41 1 ⅝ 41 1.4 0.64 435 30

3 80 3 ¼ 83 1 ⅞ 48 1 ¾ 44 1.9 0.86 435 30

4 100 3 ¾ 95 2 51 1 ⅝ 41 3.0 1.36 232 16

6 150 7 1/4 184 2 3/4 69 2 7/8 74 4.4 2.00 232 16

8 200 9 5/8 245 3 76 3 3/8 86 6.2 2.82 232 16

10 250 10 1/8 257 3 1/4 83 3 1/2 89 8.6 3.91 232 16

12 300 11 1/8 282 3 3/8 86 3 7/8 98 12.6 5.73 232 16

14 350 15 381 5 3/8 137 5 1/2 140 19.5 8.86 232 16

16 400 16 406 5 1/2 140 5 1/2 140 24.0 10.91 232 16(1) Nominal make-up dimension for drawing layout work only using non-threaded spigots. Do not use for assembly dimensions.



Fiber Glass Systems17115 San Pedro Avenue, Ste 200San Antonio, Texas 78232 USAPhone: 210 477 7500Fax: 210 477 7560

National Oilwell Varco has produced this brochure for general information only, and it is not intended for design purposes. Although every effort has been made to maintain the accuracy and reliability of its contents, National Oilwell Varco in no way assumes responsibility for liability for any loss, damage or injury resulting from the use of information and data herein nor is any warranty expressed or implied. Always cross-reference the bulletin date with the most current version listed at the web site noted in this literature.

© 2017 National Oilwell Varco All Rights ReservedCI1360ENG August 2017

Documents

HP 16 Epoxy Fittings - National Oilwell Varco · 4 HP 16 Epoxy Fittings View of Fitting Illustrations Reducing Tee Reducing Tee(1) - 1"-16" parts are available in Green Thread HP