8/6/2019 How to Setup 101

1/2

How to setup 101,110, 119 DTV in one dish:

Here is what you need.....

A: 1-18, 24 or 33 inch dish

B: 3 circular LNBs.

C: Measuring device. I used a tape measure. A ruler that can measure out

1/2 inch.

Here is what you do......

Connect all 3 Lnbf to the Super Mount. Now move it so it is about 1/2 inch

higher than the first. Move it so it is about 1/2 inch higher than the second.

The 1/2 inch does not have to be exact, but fairly close. The Mount has

ruler mark. Hopefully, between reading and looking at the pictures, you'll

make it work. First time setup took quite some time to get it figured out.

The LNB on your right will be looking at Sat. 101, the middle one 110, and

the left oneWill be 119. Mount the LNB back to a dish. Mount the middle one to dish

just like normal. As for tuning, hooked up Directv to the 101 LNB and tuned

it till had signal. You could also hook up DISH to the 119 LNB and tune it in.

Once you have one of them working, the other two LNBF WILL be seeing

signal at its respective Sat. You will probably have to compromise on signal strength depending on where you are

and what you are watching.

This is working for Dishnetwork 110, 119, 121 too. But, between 119 and 121 will more close and almost on the

same level.

This is working for BEV 82, 91, 97 too.

You can add more Super mount finger in order to add more LNB to dish and receive more satellite in one dish. Forexample, we can put Dishnet 110,119,121, Bev 91 together. Or combine with FTA LNB and receiver DSS satellite

and FTA satellite together.

How to setup 110, 119, 121 in one dish (super Dish) by using

this Mount

Here is what you need.....

A: 24 or 33 inch dish

B: 2 circular LNBs. 1- ku-linear Standard LNB.

C: Measuring device. I used a tape measure. A ruler that can measure

out 1/2 inch. (The mount already mark the ruler on the holder)

Here is what you do......

Mounted the ku-linear Lnb to the dish arm and mounted a 1/2" conduit pipe 6" long. I located and locked onto sat

121 with the highest quality possible and mounted the circular DN Lnbf for 119 to the right of 121 (looking at it from

behind the dish) and then mounted the circular DN 110 Lnbf to the right of 119.

The brackets that hold the Lnbf are from 1/2" to 2" pipe clamps/brackets. With this kind of setup you can get 4 axes

points adjustments: forwards/backwards, up/down, left/right, side to side. The quality for 110 will get from 90% to

to setup 101 http://www.mxmart.com/info/brac

2 19/04/2011 0

8/6/2019 How to Setup 101

2/2

100% , For 119 will get 80% to 98% and for 121 will get 70% to 95% depending on the transponder, But you would

need to play with 119 to get the best quality you can for the both 119 and 121. With this kind of setup should get

82, 91, and 97 on one dish too.

How to setup 82, 91, and 97 in one dish (super Dish) by using Mount

Here is what you need.....

A: 24 or 33 inch dish

B: 2 circular LNBs, 1- ku-linear Standard LNBF.

C: Measuring device. I used a tape measure. A ruler that can measure out 1/2 inch. (The mount already mark the

ruler on the holder)

setup same as ----How to setup 110, 119, 121 in one dish (supper Dish)

You can set up 110, 119, 121, 91 in one dish by using this Magic Mount

We can setup 110, 119, 121, 91, 97 AMC4 in one dish by using this Magic Mount

We can also setup T5, G3C, G13, AMC4 in one dish by using this Magic Mount

Much more...

to setup 101 http://www.mxmart.com/info/brac

2 19/04/2011 0