HOW TO OPERATE VIPER SCRUBBERS

PRE-OPERATION STEPS:

SWEEP OR DUST MOP the surface to be cleaned for best results. Remove any large debris from the floor.

CHECK BATTERIES to make sure they are fully charged. If not, charge the batteries using the correct charger. Refer to the owner’s manual for detailed instruction. Unplug the charger when done.CHECK SOLUTION in the solution tank to make sure it is the right type of solution for the task at hand.

CHECK SQUEEGEE ASSEMBLY for proper installation. To install: 1) Pull back on the squeegee lift lever to raise bracket up. 2) Loosen the two knobs on the squeegee. 3) Slide the squeegee into the slots at rear of squeegee bracket. 4) Tighten both knobs. 5) Connect the vacuum hose.

CHECK PAD DRIVER(S) or BRUSH(ES), make sure they are CLEAN and properly in-stalled. To install: 1) Make sure machine is OFF. 2) Make sure squeegee assembly is RE-MOVED. 2) Press foot pedal to lower pad/brush deck to floor. 3) Make sure tanks are empty. 4) Tilt the machine back to access the driver(s). 5) Place the brush(es) or pad(s) onto driver.

FILL SOLUTION TANK in the front of the scrubber with the proper amount of water and chemical solution using a hose or bucket. Make sure the recovery tank is empty & the vacuum float shut-off is working.

FILL SOLUTION TANK in the back of the scrubber in tight spaces with the proper amount of water and chemical solution. Make sure the recovery tank is empty and the vacuum float shut-off is working.

CHECK CLEAR SIGHT TUBE which shows how full the solution tank is with the water and chemical solution.

TWIST KEY to turn the scrubber power ON.

ADJUST WATER FLOW KNOB to adjust the amount of water applied for light surface cleaning or deep scrubbing.

FLIP ON SWITCHES for the vacuum, brush, and water. (Note: nothing will operate or flow until the handle triggers are squeezed.)

LOWER BRUSH/PAD DECK DOWN, place foot on the pedal, push down, and release.

LOWER SQUEEGEE ASSEMBLY TO THE FLOOR by pulling squeegee lever out and re-leasing. Lever location varies based on model.

SQUEEZE ONE OR BOTH HANDLE TRIG-GERS to activate the vacuum, brush, and water flow. Begin scrubbing your floors walking in an overlapping pattern. To stop everything, simply release the handle triggers.

FINAL STEPS, remove drain hose from hold-er, twist off plug, and drain. To completely drain tank for storage: hinge open recovery tank, remove clear cover, let tank rest on the support stand, and drain. Flush tank with clean water. Leave everything open to fully dry out the tank and hoses to reduce odor and bacteria. Remove pads/brushes, clean them, and hang them to dry for next time. Twist key to power OFF. Remove key and safely store the key and the scrubber.

WHEN RECOVERY TANK IS FULL flip all of the switches OFF, turn the power OFF, and raise the squeegee and pad/brush to UP position. Roll the machine to approved area to drain the recovery tank.

TO CONTINUE SCRUBBING repeat steps 1 through 13. Thank you for choosing Viper for your floor care needs.

STEPS TO OPERATE:

ADJUST THE CONTROL HOUSING to a comfortable operating height by squeezing the thumb levers directly under the control housing.

CHECK FOR FOAM once in a while through the clear recovery tank lid. If there is foam build-up, add a defoamer to recovery tank.Foam must not enter the float shut-off screen or damage can occur to vacuum motor.

CHECK BATTERY METER, AND THE CLEAR SIGHT TUBE. Recharge the batter-ies when they’re low. If battery meter is in the red, do NOT operate as battery damage may result. Make sure you have enough cleaning solution in your solution tank at all times.

1 2 3 4

9

15 16

1 2 3 4

10 12

13 14

5 6 7 8

Viper is a Brand of Simple. Rugged. Affordable.

MORE DETAILED INFORMATION ON HOW TO OPERATE VIPER AUTOMATIC SCRUBBERS CAN BE FOUND IN THE OWNER’S MANUALS LOCATED ON OUR WEBSITE:

WWW.USVIPER.COM

CHECK PAD PRESSURE, the larger scrub-bers have pad pressure meters. Check the meter to make sure the pad pressure is correct for the type of floor or cleaning to be done.

11

REV 1/2014