How to Flash T-Mobile to Android

8/2/2019 How to Flash T-Mobile to Android

1/11

How to flash T-Mobile HD from WinMobile to Android

unpack this File

You get this folders

This is the driver for MT6516

This is the driver for flashcable

USB to serial

This is the IMEI write Tool

This is the FlashTool

In this folder is the complete system

Android folder incl. scatter.txt

Database for IMEI Tool

Important: Note your IMEI Number !!!

The IMEI Number is behind the battery in the phone


2/11

1. Install the driver for the flashcable

remember the com-port

2. Start the flashTool


3/11

Select your com-port

Select your baudrate


4/11

1. Choose project WinMo

2. Search MTK_AllInOne_DA.bin

3. Search MT6516_WinMo_scatter.txt

4. Press format

Check this box, its slower but saver


5/11

9. You can set the format length according to the size of the Rom

of your phone. If the rom is 256 M, you can set it to

0x10000000. If the rom is 512 M, you can set it to 0x20000000.

10. Please select OK, when you finish the setting.

11. Connect the flex cable from your phone to the PC. Your

phone should be off power at this moment.

12. press and hold the power key on your phone until the

progress bar start to move.(If the progress bar hasnt moved,

you just to remove the battery and put it on again to try.)

The green progress bar takes app. 7-8 minutes. Hold the

powerkey all the times.

13.It will pop up the OK when the setting have finished.


6/11

Now we are ready to flash to ANDROID

Start the FLASH TOOL

1. Select Android on the point 1

2. Please note the point 2, here is set to the

T6516_Android_scatter.txt, this software is a loader file which is to

guide the whole flashing process.

3. In general, we provided Android rom will have this file. Please use

the file within the Android Rom instead of the same name file of the

kit.

4. Finally, according to the chart above to do the settings of each file

for the Android. Double-click the file name, it will pop up the file

selection box.

5. Please Double-click the UBOOT of point 3 and select the file with

uboot as prefix within the rom package if the point 3 cant load the file

automatically.


7/11

Install the driver of MTK usb( If you have finished this setting,

please do the next steps)

Please click the download( Please plug the special flex cable of 2303 and regular data cable to the

PC, because you need to use the data cable during the flexing.)

Now press and hold the power key on your phone until the progress bar start to move.( If the

progress bar doesnt move, you just to remove the battery and put it on to try again.)

Please plug the data cable after the progress bar finished 2 times 100%. Now the PC will tell you it

had found the new hardware of mt6516.

Now you need to use the driver of mtk usb. During setting the driver, it just can appear this driver

The mt6516 will only show up for one minute. If you see it was gone from the list of device

manager, please remove the data cable and then plug it again, then mt6516 will be shown up

again

When the driver has been installed, remove the USB data cable and then plug it again. Now youshould be able to find the usb modem driver in the PC device manager, that means the driver has

been installed successfully.

5Flex the Android

Please click the download( Please plug the special flex cable of 2303 and regular data cable to the

PC, because you need to use the data cable during the flexing.)

Now press and hold the power key on your phone until the progress bar start to move.( If the

progress bar doesnt move, you just to remove the battery and put it on to try again.)

Please plug the USB after the progress bar finished 2 times 100%. It will pop up the OK when the

flexing is completed.


8/11

Before the yellow bar start, you have to look here !

Because after the red and the purple bar you have only

5 Seconds to plug in the USB Data Cable. So you use the

flashcable and the USB Datacable at the same time.

If it was finish there popup a OK

Kongratulation

The next step is to write the IMEI into the phone

The IMEI Number is behind the battery in the phone


9/11


10/11

according to the chart above to do the settings:

1 = write IMEI+BackUP nvram

2 = smartphone

3 = meta mode

4 = 115200

5 = Input the port of the flex cable had contacted by your PC

6 = active this box

7 = active this box

8 = Browse and open

BPLGUInfoCustomApp_MT6516_S01_MAUI_10A_W10_48

within the Rom package

9 = Browse and open APDB_MT6516_S01_10YW1048MP_W10.52

within the Rom package

Now press Start or F6

Type your IMEI in

Two times the same number1234567891011

1234567891011

For example


11/11

press enter, press and hold the power key on your phone after

inserting the battery, then you can see the meta mode in the left

botton corner on your phone

Wait for this picture as blew appeared on your PC,

then the IMEI flexing process is finished.

If all is fine, you phone looks like mine

Best regards and good luck from GeoBroker from chinamobiles.org

Documents

How to Flash T-Mobile to Android