How to Commissioning FMR_q

8/12/2019 How to Commissioning FMR_q

http://slidepdf.com/reader/full/how-to-commissioning-fmrq 1/10

DN0947037

Issue 01

10/06/2010

© Nokia Siemens Networks 1 (10)

Nokia Siemens NetworksGSM/EDGE BSS,Rel. RG10(BSS),Operating Documentation,Issue 06

Quick Guide for Flexi MultiradioBTS GSM/EDGECommissioning

DN0947037

Issue 01Approval Date 2010-06-10



DN0947037

Issue 01

10/06/2010


The information in this document is subject to change without notice and describes onlythe product defined in the introduction of this documentation. This document is not anofficial customer document and Nokia Siemens Networks does not take responsibility forany errors or omissions in this document. This document is intended for the use of NokiaSiemens Networks customers only for the purposes of the agreement under which thedocument is submitted. No part of this documentation may be used, reproduced,

modified or transmitted in any form or means without the prior written permission ofNokia Siemens Networks. The documentation has been prepared to be used byprofessional and properly trained personnel, and the customer assumes fullresponsibility when using it. Nokia Siemens Networks welcomes customer comments aspart of the process of continuous development and improvement of the documentation.

The information or statements given in this documentation concerning the suitability,capacity or performance of the mentioned hardware or software products are given “asis” and all liability arising in connection with such hardware or software products shall bedefined conclusively and finally in a separate agreement between Nokia SiemensNetworks and the customer.

IN NO EVENT WILL Nokia Siemens Networks BE LIABLE FOR ERRORS IN THISDOCUMENTATION OR FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TOSPECIAL, DIRECT, INDIRECT, INCIDENTAL OR CONSEQUENTIAL OR ANYLOSSES SUCH AS BUT NOT LIMITED TO LOSS OF PROFIT, REVENUE, BUSINESSINTERRUPTION, BUSINESS OPPORTUNITY OR DATA, that might arise from the useof this document or the information in it.

THE CONTENTS OF THIS DOCUMENT ARE PROVIDED "AS IS". EXCEPT ASREQUIRED BY APPLICABLE MANDATORY LAW, NO WARRANTIES OF ANY KIND,EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIEDWARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE

AND NON-INFRINGEMENT, ARE MADE IN RELATION TO THE ACCURACY,RELIABILITY OR CONTENTS OF THIS DOCUMENT. NOKIA SIEMENS NETWORKSRESERVES THE RIGHT TO REVISE THIS DOCUMENT OR WITHDRAW IT AT ANYTIME WITHOUT PRIOR NOTICE.

This document and the product it describes are considered protected by copyrights andother intellectual property rights according to the applicable laws.

The wave logo is a trademark of Nokia Siemens Networks Oy. Nokia is a registeredtrademark of Nokia Corporation. Siemens is a registered trademark of Siemens AG.

Other product names mentioned in this document may be trademarks of their respectiveowners, and they are mentioned for identification purposes only.

Copyright © Nokia Siemens Networks 2010. All rights reserved.



DN0947037

Issue 01

10/06/2010


1Introduction

This document describes how to commission Flexi Multiradio BTS GSM/EDGE. The Commissionfrom SCF option is described in this document. See Flexi Multiradio BTS GSM/EDGE customerdocumentation for additional information, such as manual commissioning and troubleshootinginstructions.

This document assumes that the needed configuration has been created in the BSC, and that theneeded transmission path has been configured and connected up to the last hop to the BTS.

The following are briefly described in this Quick Guide:

• 2G Flexi BTS Site Manager connection setup• Flexi Multiradio BTS commissioning

The prerequisites before commissioning are as follows:• The 2G Flexi BTS Site Manager is installed on the PC• The BTS SW to be used is available on the PC for a local SW upgrade• The required SCF file is available on the PC for SCF file commissioning

2 2G Flexi BTS Site Managerconnection setup

1. Change IP address settings in Windows XP.

Select Start Settings Network Connections.

Select Local Area Connection.



Click Properties in the Local Area Connection Status dialog box. Select Internet Protocol(TCP/IP), and click Properties in the Local Area Connection Properties dialog box. Select Use thefollowing IP address and define the IP addresses. Click OK.

DN0947037

Issue 01

10/06/2010


Note

If you have a personal firewall installed on your PC, you need administrator rights to setthe IP address of the BTS in the friend list of your firewall.

2. Perform a visual check to the BTS:

• the grounding• power cabling



DN0947037

Issue 01

10/06/2010


• LED status during power up• TX/RX antenna connector torque check (7/16 connector 25Nm)

3. Connect the Ethernet cable from the PC to the Flexi Multiradio BTS.

4. Check and connect E1/T1 or Flexbus cables to transmission card.

5. Start 2G Flexi BTS Site Manager by clicking the icon on your desktop. The Task Selectionview opens.

6. If you want to establish a local connection, select the Local Connection option. Enter theBTS IP address and Password, and click Connect to establish the connection. Entering thepassword in not mandatory.

7. If you want to establish a remote connection, select the Remote Connection option. Enter thevalues for the fields, and click Connect to establish the connection. All the fields except BTSPassword are mandatory.



DN0947037

Issue 01

10/06/2010


The user can recommission a site using a remote connection.

8. In order to prevent errors in commissioning and reduce the time required to commission andintegrate the BTS into the network, it is recommended to download the BTS software locallyusing the 2G Flexi BTS Site Manager. Select BTS SW SW Update.



DN0947037

Issue 01

10/06/2010


Download the SW release that has been attached to the BCF at the BSC. After the softwaredownload is complete, the BTS site is automatically reset.

9. If you need to commission FIFA and microwave radios, choose the Transmission LaunchFlexiHub Manager menu item. The Nokia FlexiHub Manager main window opens.

3 Flexi Multiradio BTS GSM/ EDGEcommissioning

All the parameters in the SCF file need to be defined according to the radio network plan. Checkthat correct SCF file is used during commissioning.



DN0947037

Issue 01

10/06/2010


Note

In case the transmission plug-in unit (PIU) module type changes, perform UndoCommissioning with removal of bypass traffic after the new PIU is inserted. After that,commission the Flexi Multiradio BTS.

1. Select the Commissioning Wizard menu item or click the Commissioning button on theView Bar. The Goal selection page opens.

2. Select the Commission from SCF option.

3. Browse for the SCF file by clicking the Browse button. All the commissioning parameters areloaded from the SCF. You cannot make any changes to the parameters before sending it tothe BTS.



DN0947037

Issue 01

10/06/2010


4. Click Next to continue. The Site Commissioning File page opens.



DN0947037

Issue 01

10/06/2010


5. Click Send SCF. After the BTS has been successfully commissioned click Finish.

6. To see the commissioning report, click Show Report.

Documents

How to Commissioning FMR_q