Upload
christopher-rogers
View
213
Download
0
Embed Size (px)
Citation preview
7/28/2019 How to Build a Garden Shed From Scratch1681scribd
http://slidepdf.com/reader/full/how-to-build-a-garden-shed-from-scratch1681scribd 1/5
how to build a garden shed from scratch
Modular construction and inexpensive materials make this shed easy to build and easy to afford.
We'll show you how to build this shed and provide you with the plans and materials list you need
to get started. Don't be intimidated by the size of this project. We use simple construction
methods to make the building process as easy as possible.
We designed this shed with money saving in mind. Even the dimensions are designed to make
the most efficient use of lumber. Here are some of the ways you'll save with our shed design.
how to build a wood shed
OSB siding
Siding panels made from oriented strand board cost far less than solid wood or plywood panels,
and come preprimed, saving you money and labor. Since the panels are also structural, you don't
need an additional layer of sheathing under the siding. You'll save about $500 over the cost of
cedar plywood siding.
Wood foundation
Hiring a concrete contractor to pour a slab for this shed could cost you $1,000, but the materials
for this wood foundation will set you back only about $250. Plus, a wood foundation is easy to
build even on sites that slope or have difficult access.
Cost-cutting custom door
Materials for this door cost about $140. A similar style prehung exterior door can easily cost morethan $1,000. Of course, this door isn't as weather-tight as a prehung door, and it wouldn't work on
your house, but it's perfect for a shed. You get the look of an expensive custom wood door
without the cost. building a pole shed
Easy arch-top windows
If you've ever priced arch-top windows, you know how expensive they can be. Even windows that
don't operate are likely to cost $400 apiece. But you can simulate the look of an expensive
window without spending a ton of money. These windows cost about $60 each and are easy to
build with materials you'll find at any home center or lumberyard.
Composite trim
Composite trim saves you money and time right away. It's less expensive than solid wood (you'll
save up to $160), it doesn't have knots or other defects to work around, and it comes preprimed
and ready for paint. And it'll save you time and money in the long run since it holds paint better
and longer than even the best-quality exterior wood.
Arch-top windows and a custom door give this shed a high-quality look that belies its low cost and
simple construction. The panelized construction technique means you could build the parts in
your garage on a rainy weekend and then haul them to the site for assembly. Modest finishes like
OSB siding and composite trim and fiberglass shingles help keep the materials cost low. And
7/28/2019 How to Build a Garden Shed From Scratch1681scribd
http://slidepdf.com/reader/full/how-to-build-a-garden-shed-from-scratch1681scribd 2/5
you'll save hundreds of dollars by providing your own labor to build the door and windows. The
modular construction and wood platform foundation mean you can construct this shed almost
anywhere, even on remote or sloping sites. In this article, we'll show you the basics of how to
build the shed and install the windows and doors. shed building plans free
We found all the materials to build this shed at our local home center. Most of the construction is
straightforward and requires only standard carpentry tools and a circular saw. To build the
windows and door, you'll also need a table saw, power miter saw and router. We used a Kreg
pocket hole jig and pocket hole screws to assemble the door and windows. With a helper or two,
you could have the platform and shell built in two or three days. Then expect to spend four or five
more days completing the siding, trim, doors, windows and roofing.
A few weeks before you start, check with your local building department to see whether a permit
is required and to find out how close to the lot lines you can build. Then call 811 for instructions
on how to locate buried utility lines. The first step is to set a pair of treated 6x6s on gravel beds as
a foundation for the shed platform.
When you've decided on a shed location, dig two trenches 16 in. wide, 12 in. deep and 13 ft. long.
Center the trenches 66 in. apart. Fill the trenches with a 3-in. layer of gravel and compact it with a
hand tamper. Repeat this process until the trench is full. Use a level and long board to level the
top layer of gravel. If the ground is flat, also make sure the gravel beds in the two trenches are
level with each other.
Cut the treated 6x6s to 12 ft. and set them on the gravel so they're parallel and the outside edgesare 6 ft. apart. On sloped ground, you'll have to raise the 6x6 on the low side until it's level with
the adjacent 6x6. Do this by stacking treated 2x6s, 4x6s or 6x6s on top of the treated 6x6 to reach
the right height. Use a 4-ft. or longer level to make sure the 6x6s are level and level with each
other. Finally, square the 6x6s by adjusting the position of one 6x6. Slide the 6x6 back and forth,
not sideways, until the diagonal measurements from opposite corners are equal. Build the
platform with treated 2x6s, 24 in. on center, and cover it with treated 3/4-in. plywood.
You can build the walls on any flat surface, but the shed platform is ideal. Snap chalk lines on the
plywood deck, 3-1/2 in. from the edges of the platform, to indicate the inside edge of the walls.
Measure to make sure the lines are parallel and 89 in. apart. Then chalk a line down the center
(Photo 1). You'll use this line to make sure the angled top plates meet in the center.
Use dimensions from Figure C (in Additional Information below) to snap lines for the peak. Then
cut 2x4s to fit inside the lines and toe-screw them to the plywood to hold them in place while you
fill in the center studs (Photo 1) and nail on the siding (Photo 2). Toe-screw from the outside so
the screws will be accessible after the siding is installed.
When you nail on the siding, make sure it overhangs the framing on each side by 3-1/2 in. and
that you've trimmed off the top corner to follow the slope of the angled top plate (Photo 2). Attach
the siding with 2-in. galvanized or stainless steel ring-shank siding nails placed 8 in. apart along
7/28/2019 How to Build a Garden Shed From Scratch1681scribd
http://slidepdf.com/reader/full/how-to-build-a-garden-shed-from-scratch1681scribd 3/5
studs and 6 in. apart along the edges of the sheets. You'll have to nail blocking between the studs
to support the top edge of the siding and the Z-flashing.
Complete the siding, then remove the toe-screws and move the wall aside to make room for
constructing the opposite wall. Use the same chalk line template and process to build the
opposite end wall. Figure C (in Additional Information below) shows framing details for the front
wall. Mark the curves on the 2x10 header pieces using the trammel setup shown in Photo 12 and
Figure G (in Additional Information below). Cut them with a jigsaw. When you're done building the
front and back walls, set them aside so you can use the platform to build the roof sections.
It's unconventional, but building the roof upside down on the platform has advantages. First, you
avoid a lot of ladder work. And second, you can nail the soffit material to the overhangs easily
without having to work overhead and in cramped spaces. You do have to take a little extra care to
make sure the framing is square and the perimeter 2x4s are perfectly straight before nailing on
the soffit, though. Start by cutting out the rafters using the pattern in Figure D (in Additional
Information below) as a guide.
Omit the bird's-mouth from four rafters and use these on the ends. Cut the 2x4s for the ridge and
subfascia to length and mark the rafter positions on them. Line up the rafters with the marks and
nail through the ridge and subfascia with 16d nails to secure them. When the roof frame is
complete, line up the subfascia with the chalk line on the platform and tack it in three or four
places with toe screws to hold the frame straight while you install the soffit.
Also square the frame by making sure diagonal measurements from opposite corners are equal.Then tack one corner to hold it square. Finally, nail the soffit to the roof frame with 6d galvanized
box nails. We used 12-in.-wide fiber cement siding for soffit material. Mount an inexpensive
carbide blade on your circular saw to cut the fiber cement. Set the roof panel aside and build the
other half of the roof using the same techniques.
Start by moving one of the end panels into place and resting the bottom plate of the wall on the
platform. Tip the wall up and secure it with a temporary angled 2x4 brace. Line up the bottom
plate with the chalk line and drive a few 3-in. screws or 16d nails through the plate to hold the
bottom of the wall in position.
Don't worry about getting the wall plumb yet. It'll be automatic when you stand the back wall and
connect the corners.
Stand the back wall. Then align the corner of the side and back walls and nail them together. With
a helper on the outside of the shed to push if necessary, line up the inside edge of the bottom
plate with the chalk line and nail it to the platform. Continue around the building, standing the
opposite end wall and finally the front wall. Nail the corners together, making sure that the top
plates of adjoining walls are flush with each other.
The roof panels are heavy and a bit awkward, so round up three strong helpers for this part of the
7/28/2019 How to Build a Garden Shed From Scratch1681scribd
http://slidepdf.com/reader/full/how-to-build-a-garden-shed-from-scratch1681scribd 4/5
job. Move the panels into position and lean them against the front and back walls. Then set up
ladders inside the building for two helpers and push one of the panels up to them. Slide the panel
up the roof until the bird's-mouths drop over the top plate of the wall.
Make sure the 2x4 ridge is perfectly aligned with the peak of the wall. Then secure the roof panel
with a pair of toenails through each bird's-mouth into the top plate of the wall. Repeat the process
on the opposite side (Photo 6). Complete the roof framing by nailing the 2x4 ridges together and
adding two 2x4 collar ties, 4 ft. apart.
Ordering a prehung wood door like this from the lumberyard could cost as much as $1,000, but
you can build one suitable for a shed at a fraction of the cost. We purchased clear pine at a home
center and spent $120 for the boards. Photos 8 - 10 show how to build the door and mount it to a
trim piece with hinges. The door consists of two layers of 3/4-in.-thick boards that overlap at the
corners to add strength. Rip 1x6 boards to 4-1/2 in. on a table saw for the outside layer (Figure F,
Additional Information below).
We assembled each layer with pocket screws before gluing the two layers together, but if you
don't own a pocket hole setup, you could simply screw through the overlapping boards instead.
Complete the door frame. Then cut the 4 x 8-ft. grooved plywood to fit the lower recess, and cut a
piece of 1/4-in. acrylic sheet to fit the upper recess. Secure the plywood and acrylic sheet with
1/2-in. x 1/2-in. moldings nailed to the inside. Sand the edges of the door flush.
We've simplified the door-hanging process by mounting the door to a 1-1/2-in.-thick trim piece and
then screwing the trim to the wall. An easy way to mark and cut matching hinge recesses in boththe door and the trim is to clamp the trim alongside the door, making sure it extends 1/8 in.
beyond the top of the door. Then mark the hinge cutout on both the door and the trim at the same
time.
If you have a router, use a hinge-mortising bit (or straight bit) to cut the hinge recesses (Photo
10). Otherwise, use a sharp chisel. Screw the hinges to the door and trim. To hang the door, line
up a temporary 2x4 with the bottom of the siding and screw it to the wall. Then rest the door on
the 2x4 and drive 3-in. screws through the trim into the framing to hold the door in place (Photo
11). Finish the door installation by adding the top and side trim pieces.
This is a good rainy day project since you'll build these parts in your garage or shop. Photos 12 -
14 show how to cut the curved window top and how to assemble the window.
Figure G (in Additional Information below) shows details for the marking jig. Photo 12 shows how
to use this setup to draw the curves for the window pieces. Next cut the side pieces (Figure F, in
Additional Information below). Set the side pieces in place over the top of the header and mark
the angled cuts (Photo 13). Finish the curved trim piece by first cutting the angles on each end,
and then sawing the curves with a jigsaw and sanding them smooth. Use the marking jig to lay
out the curved brace, too (Figure G, in Additional Information below).
7/28/2019 How to Build a Garden Shed From Scratch1681scribd
http://slidepdf.com/reader/full/how-to-build-a-garden-shed-from-scratch1681scribd 5/5
Cut the sill piece and assemble the windows with pocket screws. Using a router with a 3/8-in.
rabbet bit, rout a 3/8-in.-deep recess on the back of the window to receive the 1/4-in. Plexiglas
acrylic sheet (Photo 14). Set the window frame, recessed side down, over a piece of acrylic sheet
and trace the shape with a permanent marker. Cut the curve with a fine-tooth jigsaw blade and
the straight sections with a fine-tooth blade in a table saw or circular saw.
Prime and paint the window and let it dry. Then apply a thin bead of clear silicone in the recess
and embed the acrylic sheet in it. Secure the acrylic sheet with glazing points. Let it set up
overnight. We cut the grid pieces from 3/4-in. x 1/2-in. parting stop and glued them to the acrylic
with clear silicone caulk.
A temporary support makes it simple to install the window. Level a 2x4 and screw it to the wall 2
in. below the window opening. Then rest the window on the 2x4 and center it in the opening
before driving screws to secure it (Photo 15). Use caulk to fill the gaps left by the grooved siding.
Install the exterior trim
Figure A (above) and Figure E (in Additional Information below) show the exterior trim details.
Start by mounting the brackets. Line up the outside edges of the lower brackets with the face of
the siding, push them tight to the soffit and screw them to the wall. Center the top bracket on the
peak and push it tight to the soffit. Starting with the pieces that go under the brackets, wrap the
corners with the corner board. Overlap the front corner board onto the side corner board (Figure
E, in Additional Information below).
Get ready for roofing by adding the fascia boards and shingle molding. Photo 7 shows how tonotch the fascia boards to fit around the brackets. Keep the 1x2 shingle molding flush to the top of
the roof plywood.
Roof, stain and paint the shed
Complete the shed by installing shingles and finishing the exterior. For information on how to
install shingles, go to thefamilyhandyman.com and search for “roofing."
Prime and paint the doors and windows before installing them, then you only need to caulk and fill
nail holes before rolling an additional coat of paint onto the flat surfaces. The LP SmartSide panel
siding, the composite fascia and corners, and the fiber cement soffit were all preprimed and
required only two coats of paint to finish.