HOOVER ENGLISH ,-_ pp. 1-17

ESPAI_OL _ pbg. 18-27

FRAN(_AIS 4 p. 28-37

Deep Cleaner withAuto Rinse TM

FeatureThe Easy to Use Deep Cleaner

SteamVac TM Dual V TM Deep Cleaner cleans carpet fibers byapplying hot tap water and cleaning solution.

www.hoover.com

Important Safeguards!When using an electrical appliance, always follow basic precautions, includingthe following:

READ ALL INSTRUCTIONS BEFORE USING APPLIANCE.

WARNING:To reduce the risk of fire, electricshock, or injury:

Use indoors only.

• Use only on surfaces moistened bythe cleaning process. Do not immerseproduct.

• Connect to a properly groundedoutlet only. See "GroundingInstructions".

• Do not clean over floor electricaloutlets.

plug. If appliance is not working as itshould, has been dropped, damaged,left outdoors, or dropped into water,take it to a Hoover Factory ServiceCenter or Authorized Hoover WarrantyService Dealer.

• Close supervision is necessarywhen any appliance is used by ornear children. Do not allow deepcleaner to be used as a toy or to run

unattended at any time.

Do not use without tanks in place.

Do not fill with water above 140_F_60°).

• Use extra care when cleaning onstairs. Do not place deep cleaner onstairs.

• Use deep cleaner only for itsintended use as described in theinstructions.

• Do not point tools toward people orpets.

• Use only commercially availableHoover SteamVac TM cleaners intendedfor machine application. Do not useany type of wax with deep cleaner.

• To assist in reducing drying time,be certain the area is well ventilatedwhen using detergents and othercleaners with this machine.

• Use only attachments recommend-ed by The Hoover Company; othersmay cause hazards.

• The use of an extension cord is notrecommended. If an extension cord isabsolutely necessary, use at least a16 gauge 3-wire cord which has a 3-prong grounding type plug and a 3-pole receptacle that accepts themachine plug.

• Keep detergents and other cleanersout of children's reach.

• Do not use to pick up flammable orcombustible liquids such as gasolineor use in areas where they may bepresent.

• Do not pick up chlorine bleach,drain cleaner, gasoline or any othertoxic material with this appliance.

• Unplug deep cleaner when not inuse. Turn off all controls beforeunplugging.

• Do not pick up anything that isburning or smoking, such as ciga-rettes, matches, or hot ashes.

Unplug before connecting the pow-ered hand tool.

• Always disconnect cord from electri-cal outlet before servicing the deepcleaner.

• Do not unplug by pulling on cord.To unplug, grasp the plug, not thecord.

• Never handle plug or appliancewith wet hands.

• Do not pull or carry by cord, usecord as a handle, close door on cordor pull cord around sharp edges orcorners. Do not run appliance overcord. Keep cord away from heatedsurfaces.

Do not use with damaged cord or

• Avoid picking up hard, sharpobjects with the deep cleaner. Theymay damage the machine.

• Keep hair, loose clothing, fingers,feet and all parts of body away fromopenings and moving parts.

• Do not put any object into open-ings. Do not use with any openingblocked; keep free of dust, lint, hair,and anything that may reduce air flow.

• To help prevent matting and resoil-Jng, avoid contact with carpets untilthey are dry. Keep children and petsaway from carpets until they are com-pletely dry.

• Store in a dry place. Do not exposemachine to freezing temperatures.

Save these instructions!

GroundingInstructions

This appliance must be grounded. If itshould malfunction or breakdown,grounding provides a path of least resis-tance for electrical current to reduce therisk of electric shock. This appliance isequipped with a cord having an equip-ment-grounding conductor (C) andgrounding plug (A). The plug must beplugged into an appropriate outlet (B)that is properly installed and groundedin accordance with all local codes andordinances.

DANGER-Improper connection of the equipment-grounding conductor can result in therisk of electric shock. Check with a qual-ified electrician or service person if youare in doubt as to whether the outlet is

properly grounded. Do not modify theplug provided with the appliance - if itwill not fit the outlet, have a proper outletinstalled by a qualified electrician. Thisappliance is for use on a nominal 120volt circuit and has a grounding plugthat looks like the plug illustrated insketch (A).

A temporary adapter (D) may be used toconnect this plug to a 2-pole receptacle(E) if a properly grounded outlet is notavailable. The temporary adapter shouldbe used only until a properly groundedoutlet (B) can be installed by a qualifiedelectrician. The green colored rigid ear,lug, or the like (F) extending from theadapter must be connected to a perma-nent ground (G) such as a properlygrounded outlet box cover. Wheneverthe adapter is used, it must be held inplace by a metal screw. NOTE: InCanada, the use of a temporary adapteris not permitted by the CanadianElectrical Code.

Thank you for choosing a HOOVER product.

If you need any assistance:Visit our webske at www.hoover.com Click on the "Service" button to findthe service outlet nearest you ORCall 1-800-944-9200 for an automated referral of service outlet locations (U.S.only) ORCall 1-330-499-9499 to speak with a representative in our ConsumerResponse Center.

PLEASE DO NOT RETURN THIS PRODUCT TO THE STORE.

Fill in and Save:'lease enter the COMPLETE model and serial numbers in the spaces provided_nd save.

The model and serial numbers are located on the:lata label on the bottom of the cleaner.

Vlodel No.

_erial No.

NUMBER

-lint: Attach your sales receipt to this owner's manual.

Verification of date of purchase may be required for warranty service of your-loover product.

Parts needed for assembly

Contentsimportant safeguards .......... 2Parts needed for assembly ....... 3Assembling deep cleaner ...... 3-5Deep cleaner description ........ 6General operation ............ 6-8

Filling the clean water tank... 7-8Emptying the recovery tank .... 8Brush speed selector ......... 7Automatic shut-off ............ 7

How to useBefore you begin ............ 9After cleaning ............. 9-10Cleaning carpet ............. 10Cleaning bare floors ......... 11Using the tools .......... 11-14

Cleaning carpeted stairs ..... 14Cleaning upholstery ....... 14

If you have a problem ......... 16Lubrication .................. 16Service ..................... 16Storage ..................... 16Warranty .................... 17

© 2002 The Hoover Companywww.hoover.com

A F

A. Deep cleanerB. Upper handleC. Handle bolts and nuts (in bag with hose)D. Hose/cord hookE. Hose/tool caddyF. HoseG. Utility tool

Accessories - vary by model

H I J

M N

Not all accessories are included with everymodel.

H. Carpet/Upholstery DetergentI. Bare Floor CleanerJ. Pre-cleanerK. Bare floor toolL. SpinScrub TM hand toolM. Stair/upholstery nozzleN. Crevice tool

Accessories not included with your model may bepurchased separately using the order form located atthe center of this manual.

3

The assembled cleaner will look like this

drawing, Model with SpinScrub TM handtool is shown,

|IP4

Attach upper handleRemove clean water tank (upper tank)from deep cleaner.

i

NOTE: If the cord protector (A) on backof handle should become dislodgedduring unpacking, make sure it is repo-sitioned properly before continuingwith assembly of your deep cleaner.With the arrow (B) on the cord protectorpointing down, press groove (C) in thecord protector into slot in the lowerhandle.

!

With cord hook (D) to back of deep cleaner,push upper handle down onto lowerhandle.

Push bolts into holes on front of handle. If

bolts will not go through hole easily, han-dle is not pushed completely down.Place nuts in recessed areas on backof the handle. Hold each nut in placewhile tightening each bolt securely (fromthe front of the handle) with a Phillipsscrew driver.

Only two nuts are needed on this model.The extra nut is net required but hasbeen provided for your convenience.

Replace clean water tank (upper tank)by positioning bottom first. Press tankinto place.

Attach hose/tool caddyThe hose/tool caddy is designed to beused either on the cleaner for easyaccess to the tools and hose, or if thetools are net going to be used, it can beremoved and hung for storage.If you do net want to attach the caddy tothe cleaner at this time, proceed to Fig.1-10 for proper hose placement on thecaddy.

i.u

Attach hose/cordhookInsert tabs on hook into slots on back ofcleaner. Snap hook onto cleaner.4

Slide tabs (E) on caddy into slots (F) onback of cleaner.

liSEI

Rotate top of caddy toward cleanerhandle. Slide caddy down so notch (G)on caddy rests in hook (H) on cleaner.

J I

Identify the hose parts before storinghose.I. Nozzle connector endJ. Solution tube

Storing hose andtoolsPress hose, a few inches from nozzleconnector end (I), into caddy. Bringhose up and over top of caddy.

i.l.uiBIs]|BP4

Press hose into opposite side of caddy.Loop hose at bottom of cleaner andpress into top of hook (K).

Loop hose over top of caddy again. Press solution tube (J) into outside ofclip (L). Loop solution tube up and pressinto opposite side of clip.

E

Snap stair/upholstery nozzle ontocaddy.

Insert top of bare floor tool (available atadditional cost if not included with yourcleaner) through "loop" on caddy. Slidetool down into place.

SpinScrub TM hand tool(not included with all models)

The SpinScrub TM hand tool is shipped ina plastic bag for protection. To removethe bag before using the tool, open tooldoor.

Continued 4 5

PuN tool down and outward.To reposition the tool, reverse this proce-dure.

How to reattach toolcover

The tool cover is designed with a break-away feature which allows it to snap freeif it is pushed open too far.

To reattach, align hinges of cover withholes on sides of tool storage area.Snap door into place.

6

Deep Cleaner Description

1

14

13

The assembled deep cleaner will look like the drawing.Model with SpinScrub TM hand tool is shown.

1. Hand grip2. Solution trigger: press to release cleaning

solution3. ON/OFF switch4. Rinse Setting switch5. SpJnScrub TM hand tool (not included with all

models)6. Carrying handle7. Clean watertank handle8. Clean water tank

9. Detergent container10. Recovery tank handle11. Recovery tank: holds dirty solution12. Recovery tank latches13. Brush setting selector14. Solution tube connection port15. Nozzle16. Hose connection port17. Cord hook: rotates for quick cord release18. Hose

19. Hose/tool caddy20. Stair/upholstery nozzle21. Bare floor tool (available at additional cost if

not included with your cleaner)22. Cord/hose hook

23. Handle release pedal

This deep cleaner is intended for householduse.

Operate deep cleaner only at voltage specifiedon data plate on back of cleaner. Plug deepcleaner into a properly grounded outlet.

ON/OFF switchTo turn cleaner ON, push switch down.

To turn cleaner OFF, push switch up.

Handle release pedalStep on pedal (A) to lower handle tooperating position. Handle does net lockinto a single position but "floats" to allowconvenient operation.

To transportTo move your deep cleaner from room toroom, put handle in upright and lockedposition, tilt deep cleaner back onwheels and push forward.

Continued 4 7

/

Carrying handleThe deep cleaner may also be lifted byplacing a hand above the upper cleansolution tank handle as shown.

Automatic shut offWhen the recovery tank (lower tank) is fullthe automatic shutoff mechanism will shutoff the deep cleaner suction (suction willbe noticeably reduced).

At that time, the yellow float disk will riseto the top of the recovery tank lid (B).The deep cleaner will no longer pick updirty solution and the motor sound willbecome noticeably higher in pitch.

When this happens, turn deep cleaneroff and empty recovery tank beforecontinuing use.

Check clean water tank also; it mayneed to be refilled.

Do not use without float and floatretainer in place. If broken or dis-lodged, take to an Authorized HooverService Center or Dealer for repair.

Brush setting selectorYour 'SteamVac' deep cleaner has twoagitator brush settings.

ON - for cleaning of carpet and barefloors

OFF - for cleaning carpets and barefloors when brushing is not desired.Slide selector button to the desired set-ting before cleaning.

Rinse Setting switchUse this switch to select a wash withrinse setting or a rinse only setting.

WASH-AutoRinse - This setting cleansyour carpet with detergent and water onthe forward stroke. On the reversestroke, a water-only rinse is appliedautomatically.

RINSE - This setting applies water-onlyrinse in both the forward and reversestrokes.

See "How to clean" section for moredetails.

The tanksClean water tank(upper tank)

The clean water tank (C) holds the waterthat will either be mixed with detergentfor cleaning the carpet or floor, or usedto rinse the carpet or floor.

The detergent container (D) is perma-nently attached to the water tank. Itholds the detergent that mixes with thewater.

How to fill

Unplug deep cleaner from electricaloutlet.

Place deep cleaner handle in theupright, locked position.

To remove tank, press down on tankhandle and pull forward.

8

W

IE

/•• • J

Carry tank to a sink.

Turn tank cap counterclockwise andremove cap.

Fill tank (E) (1 gallon) with hot tap water•CAUTION: Do not fill with water above140°F (60°C).

Replace tank cap and tighten.

To fill detergent container (F), turn capcounterclockwise and remove cap.

_IOTE: Use only HOOVER detergents.]hey are specially formulated for useMth your 'SteamVac' deep cleaner.

CAUTION: Detergents containAnionic and Nonionic Surfactants.

Avoid contact with eyes and skin. Incase of contact with eyes, flush withcold water for 15 minutes. In case ofcontact with skin, wash with water. Ifirritation persists, call a physician.For Medical Information (U.S.) call1-800-752-7869.

'\ •

Fill container (16 oz.) with HOOVERCarpet/Upholstery Detergent orHOOVER Bare Floor Cleaner•

Do not use Bare Floor Cleaner on carpet orupholster_ Do not use any type of waxwith your 'SteamVac' deep cleaner.

To assure proper results, use onlyHOOVER detergent.

Replace container cap and tighten.

Position bottom of tank onto cleaner andpivot tank to snap it into place.

Recovery tank(lower tank)

The recovery tank holds the dirty solu-tion that is picked up from the surfacebeing cleaned.

When the recovery tank is full, the auto-matic shut-off will engage, suction willstop (see page 7), and the tank must beemptied•

How to emptyTurn deep cleaner off and unplugfrom electrical outlet.

To prevent possible leaking, removeclean water tank (Fig. 2-10) by pressingdown on tank handle and pulling for-ward; set tank aside (do not set tankon furniture).

Step on handle release pedal (Fig. 2-3)and lower handle until it rests on thefloor.

Turn recovery tank latches (G) outward(one on each side of tank).

Raise handle (H) straight up and lift tankoff cleaner•

Carry tank to sink or drain.

Lower handle toward back of tank tounlock lid. Lift lid off tank.Empty tank and repositien lid.For full suction, it is important thatthe recovery tank lid is properlysecured before cleaning.

Raise tank handle to carrying positionand place it onto deep cleaner• Lowerhandle to front of tank.

Turn latches (one on each side of tank)inward to lock tank in place•

Raise handle of deep cleaner to uprightposition and reposition upper clean

water tank• Continued -_ 9

Before you begincleaninga. Vacuum thoroughly - For carpet,use a HOOVER vacuum cleaner with anagitator for best results. Vacuum uphol-stery with a vacuum cleaner with clean-ing tool attachments. Use a crevice toolto reach into tufts and folds. Do not usethe 'SteamVac' deep cleaner as a dryvacuum cleaner.

b. For upholstery, check cleaningcode - Use your HOOVER 'SteamVac'deep cleaner only if the upholsteryfabric is marked with a "W" (for "wet"clean) or "S/W" (for "solvent/dry" or"wet" clean). Do not clean fabricmarked "S" ("solvent/dry" cleanonly). If your upholstery does not havea code, seek professional assistance.c. Test for colorfastness - Wet a whiteabsorbent cloth with the detergent. In asmall, hidden area, gently rub the surfacewith the dampened cloth. Wait ten minutesand check for color removal or bleed withwhite paper towel or cloth. If surface hasmore than one color, check all colors.

d. When cleaning entire floor, movefurniture out of area to be cleaned(may not be necessary ifonly high traf-fic areas are to be cleaned). For furni-ture too heavy to move, place aluminumfoil or wax paper under legs. This willprevent wood finishes from staining car-pet. Pin up furniture skirts anddraperies.

e. Pretreat spots and heavy trafficareas with HOOVER<_ PreCleaner*-Test PreCleaner for colorfastness by firstspraying it on a hidden area; wait tenminutes and blot with white papertowels or cloth.If no color change is visible, sprayPreCleaner onto spots and traffic areas.Wait at least ten minutes. Use your'SteamVac' deep cleaner to pick upPreCleaner and spot. Repeat until spot isremoved; carefully scrub with a householdscrub brush if necessar_z

Do not saturate carpet or upholstery withPreCleane:

No cleaning solution removes all stainsfrom all carpets. Stain removal varies withthe type of spill, time elapsed beforeremoval, carpet material, and carpet type.

f. To prevent staining, use plastic or alu-minum foil to protect wood or metal sur-faces from possible water spray.

g. To avoid wetting and possible damageto wood floors underneath area rugs/car-pet, either move area rugs/carpet to a non-wood bare floor surface or place waterproofmaterial (e.g. plastic) underneath thembefore cleaning.

See pages 10-14 for instructions on variouscleaning tasks.

*Available at additional cost if not includedwith your model.

After cleaninga. Allow carpet or upholstery to dry. Tohelp prevent matting and resoiling thecarpet, keep children and pets awayfrom surface until it is completely dry. Ifit is necessary to walk on damp car-pet, place towels or white cloths on thetraffic areas.

If furniture must be replaced before thecarpet is dry, place plastic or aluminumfoil under legs of furniture so metalslides or wood finishes will not stain thecarpet.

b. Empty tanks, rinse with clear waterand let air dry. Rinse the recovery tanklid and let air dry.

Any unused detergent may be left inthe detergent container for future use.

c. Remove lint from filter screen locatedinside recovery tank.

d. Remove lint from filter screen locatedon bottom of cleaner as follows.Note: When brushes seem to be rotat-ing slowly, disconnect deep cleanerfrom electical outlet and check andclean this screen.

Remove both tanks as described in Fig.2-16. Tilt cleaner back so handle restson floor.

Squeeze filter frame, lift and pull it out.Wipe off screen and push frame backinto place.

Return cleaner to upright position.

e. If desired, vacuum thoroughly aftercarpet has completely dried. This willhelp reduce any shading left by thedeep cleaner's brushes.

10

To clean nozzle

If lint or other debris becomes lodged innozzle, it can be removed for cleaning.

Unplug deep cleaner from electricaloutlet.

Remove both tanks as described in Fig.2-16. With handle in upright position, tiltcleaner back so that handle rests on thefloor.

Lift up rear edge of nozzle. Slide nozzleup and remove from cleaner.

To replace nozzle, line up tabs (A) onnozzle with holes (B) in cleaner. Slidetabs into holes.

Slide nozzle completely onto cleaner.Press down on nozzle to secure it.

Replace recovery tank (Fig. 2-17).

The nozzle must be in the properposition in order for the recovery tankto go on properly.

Raise cleaner to upright position andreplace clean water tank (Fig. 2-15).

Read "Before you begin cleaning"instructions on page 9.

1. Fill clean water tank according toinstructions for Figs. 2-9 to 2-12.

2. Fill detergent container with HOOVERCarpet/Upholstery Detergent accordingto instructions for Figs. 2-13 to 2-15.3. Turn brushes ON or OFF as desired.

4. Dry hands and plug cord into a prop-erly grounded outlet.Do not clean over floor electrical out-lets.

5. To avoid walking on damp carpet,start at the end of the room farthest fromthe door or path to sink where tanks willbe emptied and filled.

Step on handle release pedal and lowerhandle to operating position.

6. Set Rinse Setting switch to WASH-AutoRinse. Turn cleaner ON (Fig. 3-5).

1_]!-1

7. Squeeze trigger to release cleaningsolution and slowly push deep cleanerforward (equals one wet stroke).

8. Continue to squeeze trigger andslowly puN deep cleaner back toward

you (second wet stroke). The deepcleaner rinses the carpet on the back-ward pass. Note: To assure properrinsing, it is important to keep thedeep cleaner on the same path back-ward as forward.

9. Release trigger and slowly push deepcleaner forward over area just sprayedwith solution (dry stroke). Then slowlypull deep cleaner back toward you with-out squeezing trigger (dry stroke).Continue using dry strokes until littlewater is visible passing through therecovery tank lid.

10. For best results, use straight, paral-lel strokes as shown in the diagrambelow. Overlap strokes by 1 inch to helpprevent streaking.

Keep nozzle flat on floor for both for-ward and reverse strokes.

11. If you would like to rinse the carpetwith water only, set Rinse Setting switchto RINSE (Fig. 3-8). Repeat steps 7-9. Inthis setting, rinsing will be done on bothforward and reverse strokes.

Rinsing is not necessary, but will helpremove detergent residue and help yourcarpet look fresher.

12. For heavily soiled areas, repeatsteps 6-9. Avoid saturating carpet, asnoted below.

Note: To avoid saturating carpet, donot use more than 4 wet strokes overone area. Always end with drystrokes.

It is best to alternate wet and dry strokesas described above.

For best cleaning results and to aid infaster drying of carpet, end with moredry strokes. (Continue using dry strokesuntil little water is visible passing throughthe recovery tank lid.)

13. Empty recovery tank when themotor sound becomes higher pitchedand there is a loss in suction (see"Automatic shut-off", Fig. 2-6).

When finished cleaning, follow "Aftercleaning" instructions on pages 9 &10.

Continued -_ 11

How to attach bare floorattachment(Available at additional cost if not includ-ed with your cleaner.)

Unplug deep cleaner from electricaloutlet.

To prevent possible leaking, removeclean water tank (Fig. 2-10) and recov-ery tank (Fig. 2-16) before positioningbare floor attachment.Set tanks aside (do not set tank on furni-ture).

1. With handle in upright position, tiltcleaner back so that handle rests on thefloor.

2. With foam strip (C) (located under thenetting) in position as shown, placeattachment on front of nozzle (D).Make sure arrow on end of attachmentpoints in the direction as shown.

Attach hose

Unplug cleaner from electrical outlet.

3. Push attachment against nozzle whilerotating attachment downward until bothends snap into place.

(Note: Some force may be required torotate and snap attachment into place.)4. Return deep cleaner to upright posi-tion. Lower handle and replace recoverytank.

5. Raise handle to upright position andreposition clean water tank.

To clean floor

Read "Before you begin cleaning"instructions on page 9.

Do not use the deep cleaner on hard-wood floors.

1. Fill clean water tank according toinstructions for Figs. 2-9 to 2-15.

2. Fill detergent container with HOOVERBare Floor Cleaner according to instruc-tions for Figs. 2-13 to 2-15.

3. Turn brushes ON for scrubbing orOFF if scrubbing is not desired.

4. Dry hands and plug deep cleanerinto a properly grounded outlet.

5. Step on handle release pedal andlower handle to operating position.

6. Set Rinse Setting switch to WASH-AutoRinse. Turn cleaner ON.

7. To release solution, press trigger.Slowly move deep cleaner forward andbackward over area to be cleaned.Water and detergent will be released onthe forward stroke. A water-only rinse willautomatically be released on the reversestroke.

8. To pick up dirty solution, release trig-ger and slowly move deep cleaner overarea where solution has just been dis-persed. Use both forward and reversestrokes.

9. If rinsing the floor is desired, set RinseSetting switch to RINSE. Repeat steps 7& 8. This setting provides a water-onlyrins in both the forward and reversestrokes.

Rinsing is not necessary, but will helpremove detergent residue from the floor.

10. Empty recovery tank when themotor sound becomes higher pitchedand there is a loss in suction (see"Automatic shut-off", Fig. 2-6).

11. When finished cleaning, follow "Aftercleaning" instructions on pages 9 & 10.

Unplug deep cleaner from electricaloutlet and remove attachment from noz-zle. Rinse it in clear water. Do notremove plastic screen or foam fromattachment.

Insert short hose end, matching tabs onhose with same-sized slots in port.

Plug solution tube firmly into solutionconnection port (F).

Open hose connection port (E).

12

Select toolYour model includes some combinationof the following tools, but may notinclude them all.

G. SpinScrub TM hand tool has rotatingbrushes for extra scrubbing action onsmall carpet areas, carpeted stairs andupholstery.H. Stair/upholstery nozzle has a built-inbrush to help provide the scrubbingaction some spots may need forremoval.I. Crevice tool can be used to cleanalong edges of carpet, carpeted stairsand on upholstery.

How to attach tools

Unplug deep cleaner from electricaloutlet.

1. Place handle in upright position andremove hose from rack.All tools attach to the hose in the samemanner:2. Connect tool to hose by sliding it ontoconnector until the tab (J) locks itsecurely.

Using your thumb, push forward andup on the latch (K) to remove tool.

After using toolDrain suction hose by turning deepcleaner ON and holding nozzle up forseveral minutes. Do not press trigger.Unplug deep cleaner from electricaloutlet.Disconnect hose and solution tubefrom deep cleaner.

Drain solution tube by placing roundend in sink and raising nozzle aboveyour head. Press the trigger.

The tool caddy can be removed andhung on a coat hanger for storage.

Read "Before you begin cleaning"instructions on page 10.1. Attach hose and solution tube asinstructed in Figs. 3-11 to 3-13.

2. Place handle in upright position.Agitator brushes will not rotate whilehandle is in upright position.

3. Fill clean water tank according toinstructions for Figs. 2-9 to 2-12.

4. FiN detergent container with HOOVERCarpet/Upholstery Detergent accordingto instructions for Figs 2-13 to 2-15.5. Attach tool to end of hose.

6. Hose length may require thatmachine be placed at the top of thestairs to clean upper half of stairwayand at bottom of stairs to clean lowerhalf.

To prevent machine from falling, useextra caution when cleaning on stairs.

Do not place deep cleaner on stairs.

Do not point tools toward people orpets.

7. Dry hands and plug deep cleanerinto a properly grounded outlet.

8. Set Rinse Setting switch to WASH-AutoRinse. Turn cleaner ON.

Note: "Auto-rinse" and rinse are notavailable during tool use. The hose willonly dispense water mixed with deter-gent.

A

9. Pre-spray the carpeted stair by hold-ing the tool (A) or (B) about one inchabove the carpet and push it forwardwhile pressing the trigger (equals onewet stroke).

10. Position tool against the riser and slightlypress it into carpet pile. Press the triggerand pull the tool slowly over the carpet(second wet stroke). Release trigger at endof stroke.

Continued -_ 13

11. Lift tool, and position it against riser.Pull tool slowly over carpet withoutpressing trigger (dry stroke).12. Overlap strokes by 1/2 inch to helpprevent streaking.

It is best to alternate wet and drystrokes as described above. End withmore dry strokes to aid in faster dryingof carpet.

To avoid saturating carpet, do not usemore than 4 wet strokes over any onearea. Always end with dry strokes.

If additional cleanklg is necessary, waituntil the carpet is completely dry beforeusing the tool again.13. Empty recovery tank when the motor

sound becomes higher pitched andthere is a loss in suction (see Automaticshut-off", Fig. 2-6).

When finished cleaning, follow "Aftercleaning" instructions on pages 10 & 11and After using tool" instructions onpage 13.

Read "Before you begin cleaning"instructions on page 10.

Be sure to check the cleaning code onyour upholstery. Use your deep cleaneronly on upholstery marked "W" or"W/S".

1. Attach hose and solution tube as

instructed in Figs. 3-11 to 3-13.

2. Place handle in upright position.Agitator brushes will not rotate whilehandle is in upright position.

3. Fill clean water tank according toinstructions for Figs. 2-9 to 2-12.

4. Fill detergent container with HOOVERCarpet/Upholstery Detergent accordingto instructions for Figs. 2-13 to 2-15.

5. Attach tool to end of hose.

Do not point tools toward people orpets.

6. Dry hands and plug deep cleanerinto a properly grounded outlet.

7. Set Rinse Setting switch to WASH-AutoRinse. Turn cleaner ON.

Note: "Auto-rinse" and rinse are notavailable during tool use. The hose willonly dispense water mixed with deter-gent.

8. Gently press the tool onto the fabric.Press the trigger and slowly pull the noz-zle over the fabric.

9. Overlap strokes by 1/2 inch to helpprevent streaking.

Make additional strokes without pressingthe trigger to remove more moisture.

10. To clean in corners or creases, liftthe tool one-half inch from the fabric andpress the solution trigger.

11. Vacuum up the solution with the toolwithout pressing the trigger.

12. For heavily soiled areas, it may benecessary to repeat the cleaningprocess. Make crisscrossing strokes tothe original pattern; overlap each pass(Fig. 3-21 ).

Make no more than 2 passes with thesolution or rinse over any one area toprevent over-wetting and damage tofabric.

If additional cleaning is necessary, waituntil the upholstery is completely drybefore using the tool again.

13. Empty recovery tank when the motorsound becomes higher pitched andthere is a loss in suction (see "Automaticshut-df", Fig. 2-6).

When finished cleaning, follow "Aftercleaning" instructions on pages 10 & 11and "After using tool" instructions onpage 13.

Removable brushesYour deep cleaner is equipped withremovable brushes for easy cleaning.

To remove brushesDisconnect cleaner from electricaloutlet.

To prevent possible leaking, removeclean water tank and recovery tank. Settanks aside.

With handle in upright position, tiltcleaner back until handle rests on thefloor.

Grab brush assembly and pull firmly.

The brushes can be cleaned under run-

ning water.

14

B D B

To replace brushesAlign posts (A) on both ends of brushassembly with slots (B) in cleaner hous-ing.

Make sure that the square post (C) alsoaligns with the square hole (D). Turnbrushes slightly until post fits easily intohole.

Press brush assembly firmly to snap intoplace.

StorageBefore storing:

• Empty clean water tank and let airdry. Replace on deep cleaner.

• Unused detergent can be stored inthe detergent container.

• Empty recovery tank, rinse tankand lid thoroughly with clean waterand let air dry.

Allow brushes and underside of deepcleaner to air dry thoroughly beforestoring deep cleaner on a carpeted orwood surface.

Do not store deep cleaner with a fullclean water tank in place.

LubricationThe motor is equipped with bearingswhich contain sufficient lubrication forthe life of the motor. The addition oflubricant could cause damage. Do notadd lubricant to motor bearings.

If a minor problem occurs, it usually canbe solved quite easily when the cause is

found by using the check list below.

Possible causePossible solution

• Not firmly plugged in• Plug unit in firmly

• No voltage in wall receptacle• Check fuse or breaker

• Blown fuse/tripped breaker• Replace fuse/reset breaker

Possible causePossible solution

• Recovery tank full/automatic shutoff engaged

• Remove and empty recovery tank

• Blockage in tool on end of hose• Remove tool and clear blockage

• Recovery tank lid not on correctly• MaRe sure lid is on securely

• Water tank empty, but detergentremains

• Fill water tank

Possible causePosstT_/esoluhon

• Clean water tank not firmly in place• Make sure tank is securely locked in

position

• Clean water tank or detergentcontainer empty

• RefiT/container accordlbg to instruc-tions for surface being cleaned

• Recovery tank lid not oncorrectly

• Make sure lid is firmly in place

Possible causePossible solu#bn

• Valve cap clogged• Remove and clean valve cap (see fob

lowing instructions)

1. Remove clean water tank.

3. Align slots (B) on cap with tabs (C) inopening.

Turn cap clockwise to tighten.

Possible causePossible soluhbn

• Dirty filter screen on bottom of unit• Clean screen as shown in Fig 3-2

• Setting selector on OFF• Move setting selector to ON

2. Turn valve cap (A) counterclockwiseand remove.

Soak valve cap in warm water for at

least 15 minutes. Wipe cap dry. Continued ._ 15

ServiceTo obtain approved HOOVER serviceand genuine HOOVER parts, locate thenearest Hoover Factory ServiceCenter or Authorized HooverWarranty Service Dealer (Depot) by:

• checking the Service section of TheHoover Company on-line atwww.hoover.com OR

• checking the list of Factory ServiceCenters provided with this cleanerOR

• checking the Yellow Pages under"Vacuum Cleaners - Household" OR

• calling 1-800-944-9200 for anautomated referral of authorizedservice outlet locations (U.S. only).

Do not send your cleaner to The HooverCompany in North Canton for service,this will only result in delay.

If further assistance is needed, contactThe Hoover Company ConsumerResponse Center, North Canton, Ohio44720 Phone: 330-499-9499.

In Canada, contact Hoover Canada,Burlington, Ontario L7R 4A8,Phone: 1-800-263-6376.

Always identify your cleaner by thecomplete model number when request-ing information or ordering parts. (Themodel number appears on the bottom ofthe cleaner.)

Full One Year

Warranty

(Domestic Use)

Your HOOVER® appliance is warrantedin normal household use, in accordancewith the Owner's Manual against originaldefects in material and workmanship fora period of one full year from date of pur-chase. This warranty provides, at no costto you, all labor and parts to place thisappliance in correct operating conditionduring the warranted period. This war-ranty applies when the appliance is pur-chased in the United States including itsterritories and possessions, or in Canadaor from a U. S. Military Exchange.Appliances purchased elsewhere arecovered by a limited one year warrantywhich covers the cost d parts only. Thiswarranty does not apply if the applianceis used in a commercial or rental appli-cation.

Warranty service can only be obtainedby presenting the appliance to one ofthe following authorized warranty serviceoutlets. Proof of purchase will berequired before service is rendered.

1. Hoover Factory Service Centers.

2. Hoover Authorized WarrantyService Dealers (Depots).

For an automated referral of autho-rized service outlets in the U.S.A.,phone 1-800-944-9200 OR

visit The Hoover Company on-line atwww.hoover.com

This warranty does not cover pick updelivery, or house calls; however, if youmail your appliance to a Hoover FactoryService Center for warranty service,transportation will be paid one way.

While this warranty gives you specificlegal rights, you may also have otherrights which vary from state to state.

If further assistance is needed, or ifthere are questions concerning this war-ranty or the availability of warranty ser-vice outlets, write or phone theConsumer Response Center, TheHoover Company, 101 East Maple St.,North Canton, Ohio 44720,Phone 1-330-49%9499.

In Canada, contact Hoover Canada,Burlington, Ontario L7R 4A8,1-800-263-6376.

16

17