Home Network System Motion Sensor KX-HNS102AZ...Green, blinking Registration mode (You pressed and held M N) Off No battery power Note: R The LED indicator does not indicate sensor

Installation Guide

Home Network SystemMotion Sensor

Model No. KX-HNS102AZ

Thank you for purchasing a Panasonic product.

This document explains how to install the motion sensor properly.For details about how to use the system, refer to the User’s Guide(page 15).

Please read this document before using the unit and save it for futurereference.

HNS102AZ_(en_en)_0325_ver.031.pdf 1 2015/03/25 14:24:03

IntroductionAccessory information ...............3

Important InformationAbout this system ......................4For your safety ...........................4Important safety instructions ......5For best performance ................5Other information .......................6

SetupPart names and functions ..........7LED indicator .............................7Setup overview ..........................7Inserting the batteries ................8Registering the motionsensor ........................................8Information about sensorfeatures ......................................9Confirming the usage area ......11Wall mounting ..........................12

AppendixTesting the motion sensor .......15Adjusting the sensorsensitivity .................................15Features available when using the[Home Network] app ................15Accessing the User’s Guide ....15Specifications ..........................16Warranty (for New Zealand) ....17

2

Table of Contents


Accessory informationSupplied accessoriesNo. Accessory item/Part number QuantityA Batteries*1 2B Wall mounting adaptor*2 1C Wall mounting screws (25 mm) 2

*1 When replacing batteries, see “Power source” of “Specifications”, page 16for battery information.

*2 The motion sensor can be wall mounted with or without the wall mountingadaptor (page 12).

A B C

Other informationR Design and specifications are subject to change without notice.R The illustrations in these instructions may vary slightly from the actual product.

TrademarksR iPhone and iPad are trademarks of Apple Inc., registered in the U.S. and other

countries.R Android is a trademark of Google Inc.R Microsoft, Windows, and Internet Explorer are either registered trademarks or

trademarks of Microsoft Corporation in the United States and/or other countries.R All other trademarks identified herein are the property of their respective owners.

3

Introduction


About this systemR This system is an auxiliary system; it

is not designed to provide completeprotection from property loss.Panasonic will not be heldresponsible in the event thatproperty loss occurs while thissystem is in operation.

R The system’s wireless features aresubject to interference, thereforefunctionality in all situations cannotbe guaranteed. Panasonic will notbe held responsible for injury ordamage to property that occurs inthe event of wireless communicationerror or failure.

For your safetyTo prevent severe injury and loss of life/property, read this section carefullybefore using the product to ensureproper and safe operation of yourproduct.

WARNINGPower connectionR Use only the power source marked

on the product.R Do not connect non-specified

devices.

InstallationR To prevent the risk of fire or

electrical shock, do not expose theproduct to rain or any type ofmoisture.

R Do not place or use this productnear automatically controlled

devices such as automatic doorsand fire alarms. Radio wavesemitted from this product may causesuch devices to malfunctionresulting in an accident.

R Keep small parts (screws, etc.) outof the reach of children. There is arisk of swallowing. In the event theyare swallowed, seek medical adviceimmediately.

R It is advised not to use theequipment at a refuelling point.Users are reminded to observerestrictions on the use of radioequipment in fuel depots, chemicalplants or where blasting operationsare in progress.

Operating safeguardsR Do not disassemble the product.

MedicalR Consult the manufacturer of any

personal medical devices, such aspacemakers or hearing aids, todetermine if they are adequatelyshielded from external RF (radiofrequency) energy. DECT featuresoperate between 1.88 GHz and1.90 GHz with a peak transmissionpower of 250 mW.

R Do not use the product in healthcare facilities if any regulationsposted in the area instruct you not todo so. Hospitals or health carefacilities may be using equipmentthat could be sensitive to externalRF energy.

4

Important Information


CAUTIONBatteryR The batteries should be used

correctly, otherwise the product maybe damaged due to battery leakage.

R Do not charge, short-circuit,disassemble, or heat the batteries.

R Do not dispose of batteries in a fire.R Remove all the batteries when

replacing.R Do not mix old, new or different

types of batteries.R It is recommended that batteries are

replaced annually.R Keep out of the reach of small

children. There is a risk ofswallowing. If the battery isswallowed, seek medical attentionimmediately.

R Remove the battery if it becomesunusable. There is a risk of leakage,overheating, and rupture. Do notattempt to use a battery if it isleaking.

R Do not intentionally pour water onthe battery or allow it to get wet.There is a risk of fire and smoke. Ifthe battery becomes wet, remove itimmediately and contact anauthorised service centre.

Important safetyinstructionsWhen using your product, basic safetyprecautions should always be followedto reduce the risk of fire, electric shock,and injury to persons, including thefollowing:1. Do not use this product near water

for example, near a bathtub,

washbowl, kitchen sink, or laundrytub, in a wet basement or near aswimming pool.

2. Use only the batteries indicated inthis document. Do not dispose ofbatteries in a fire. They mayexplode. Check with local codes forpossible special disposalinstructions.

SAVE THESE INSTRUCTIONS

For best performanceHub location/avoiding noiseThe hub and other compatiblePanasonic devices use radio waves tocommunicate with each other.R For maximum coverage and

noise-free communications, placeyour hub:– at a convenient, high, and central

location with no obstructionsbetween the product and hub inan indoor environment.

– away from electronic appliancessuch as TVs, radios, personalcomputers, wireless devices, orother phones.

– facing away from radio frequencytransmitters, such as externalantennas of mobile phone cellstations. (Avoid putting the hubon a bay window or near awindow.)

R If the reception for a hub location isnot satisfactory, move the hub toanother location for better reception.

EnvironmentR Keep the product away from

electrical noise generating devices,

5



such as fluorescent lamps andmotors.

R The product should be kept freefrom excessive smoke, dust, hightemperature, and vibration.

R The product should not be exposedto direct sunlight.

R Do not place heavy objects on top ofthe product.

R The product should be kept awayfrom heat sources such as radiators,cookers, etc. It should not be placedin rooms where the temperature isless than 0 °C or greater than 40 °C.Damp basements should also beavoided.

R Operating the product near electricalappliances may cause interference.Move away from the electricalappliances.

Other informationCAUTION: Risk of explosion if batteryis replaced by an incorrect type.Dispose of used batteries according tothe instructions.

Routine careR Wipe the outer surface of the

product with a soft moist cloth.R Do not use benzine, thinner, or any

abrasive powder.

Information on Disposal in otherCountries outside the EuropeanUnion

These symbols are only valid in theEuropean Union. If you wish to discardthese items, please contact your localauthorities or dealer and ask for thecorrect method of disposal.

Note for the battery removalprocedureRefer to “Inserting the batteries” onpage 8.

6



Part names andfunctions

A B C D

E

Infrared sensorLED indicatorMHIGHN/MLOWNUsed to change the sensorsensitivity (page 15).Rear coverM NUsed to confirm the status of thesensor or register the sensor tothe hub.

LED indicatorYou can press M N and check theLED indicator to confirm the sensor’sstatus.

Indicator StatusGreen, lit No motion detectedRed, lit Motion was detected

Indicator StatusRed,blinking

Sensor is out of rangeof the hub

Green,blinking

Registration mode(You pressed and heldM N)

Off No battery power

Note:R The LED indicator does not indicate

sensor status if the sensor has notbeen registered (page 8).

Setup overview1 Initial setup

Make sure you can access thesystem using your mobile device.For details, refer to the SystemSetup Guide included with yourhub.

2 Insert the batteriesThe motion sensor is batterypowered.

3 RegistrationRequired only if the motion sensorwas purchased separately (i.e.,not as part of a bundle).

4 Confirm the installation areaRead the information in thisdocument to confirm that thedesired installation area is suitableto proper operation.

5 InstallationInstall the motion sensor in thedesired location.

7

Setup


Inserting thebatteriesR USE ONLY Alkaline batteries AA

(LR6) size.R Do NOT use Manganese/Ni-Cd/

Ni-MH batteries.R Confirm the polarities ( , ).1 Remove the rear cover by

pressing the upper sides of thecover (A) and sliding it down (B).

A

B

2 Insert the batteries.

3 Install the rear cover.R Place it with the “ ” mark

facing upwards and slide it.

Registering themotion sensorThis procedure is not required fordevices that were included as part ofa bundle.

Before you can use the motion sensor,it must be registered to the hub.If you purchased devices separately(i.e., not as part of a bundle), you mustregister each device to the hub.

You can register each device by usingthe registration buttons or the [HomeNetwork] app.

8

Setup


Using registration buttons1 Hub:

Press and hold M OTHERDEVICEN until the LED indicatorblinks in green.

2 Motion sensor:Press and hold M N until theLED indicator blinks in green(page 7).R When registration is complete,

the hub sounds one long beep.Note:R To cancel without registering the

sensor, press M N on the hub andon the sensor again.

R If registration fails, the hub soundsseveral short beeps.

Using the appWhen you register the motion sensorby using the [Home Network] app, youcan assign a name to your devices andgroup them by location. For moreinformation, refer to the User’s Guide(page 15).

Information aboutsensor featuresThe motion sensor utilises an infraredsensor (i.e., heat sensor).Please read the following informationbefore deciding where to install themotion sensor.Note:R The motion sensor’s sensor features

are not designed to be used insituations that require high reliability.We do not recommend use of the

motion sensor’s sensor features inthese situations.

R Panasonic takes no responsibility forany injury or damage caused by theuse of the motion sensor.

Using heat to detect motionThe motion sensor’s infrared sensorcan detect motion by recognizingtemperature differences that occurwithin the range of the sensor. It doesthis by detecting the infrared rays thatare emitted naturally by people,animals, etc., which correlate to theobject’s temperature. The detectionrange is indicated in the illustration bythe grey area in front of the motionsensor.

Detection range when looking fromabove

1

1 Horizontal detection range:approx. 90°

9

Setup


Detection range when looking fromthe side

1

2

1 Vertical detection range: approx.20°

2 Distance of detectable motion:approx. 5 m

Note:R Detection becomes difficult when

there is little difference between thetemperatures of objects and thesurrounding environment, such asduring summer. Conversely,detection becomes easier whenthere is a large difference betweenthe temperatures of objects and thesurrounding environment, such asduring winter or at night.

R Detection does not occur when thereare obstacles in front of the infraredsensor. Remove the obstacles orchange the installation location.

Direction of motionIt is easier to detect objects that movesideways in front of the motion sensor,and more difficult to detect objects that

move directly toward the front of themotion sensor.

D

A

B

C

It is difficult to detect movementdirectly towards the front of themotion sensor.It is easy to detect movementsideways in front of the motionsensor.Detection rangeMotion sensor

10

Setup


Confirming theusage areaWireless communicationrangeThe wireless communication range ofeach device in the system from the hubis approximately 50 m indoors andapproximately 300 m outdoors.Wireless communication may beunreliable when the following obstaclesare located between the hub and otherdevices.R Metal doors or screensR Walls containing aluminium-sheet

insulationR Walls made of concrete or

corrugated ironR Double-pane glass windowsR Multiple wallsR When using each device on

separate floors or in differentbuildings

Note:R You can check the motion sensor’s

communication status by pressingM N. If the LED indicator is lit ingreen or red, the sensor iscommunicating properly with thehub. If the LED indicator blinks inred, it is out of range of the hub.

Usage area cautionsUsing the motion sensor in thefollowing areas may causedeformation, malfunction, oroperational failure.R In direct sunlightR Areas exposed to grease or steam,

such as kitchens

R Near fire or heating devicesR Near magnetic fields (such as near

microwaves and magnets)R Areas subject to extreme

temperature changes, such as nextto air conditioners

R Areas with reflective objects, suchas glass, that can interfere withdetection of temperature variation

R Areas where the temperature isaffected by strong illuminatingobjects (such as fluorescent lights)

R Near devices that emit strong radiowaves, such as mobile phones

11

Setup


Wall mountingThere are two methods for wallmounting the motion sensor. To mountthe sensor flat against the wall, use therear cover. To mount the sensor so thatit faces 45° to the left or right, use thewall mounting adaptor.

Mounting examples*1 of the rearcover and wall mounting adaptor

1

A Rear cover

2

B Wall mountingadaptor

*1 View of looking from above.

Note:R Mount the motion sensor on the

stable location where the motionsensor can be adequately supportedwhen mounting.

R Do not mount motion sensor on asoft material. It may fall down, breakor cause injury.

R Do not mount the motion sensor onthe following places: gypsum board,ALC (autoclaved lightweight cellularconcrete), concrete block, plywoodless than 25.4 mm thick, etc.

Using the rear cover

1 Remove the rear cover bypressing the upper sides of thecover (A) and sliding it down (B).

A

B

2 Attach the rear cover to the wall byusing screws (1).R Place the rear cover with “UP”

mark facing upwards.R 2 37 mm

UP 21

UP

1

12

Setup


Note:R Use the following template

below when determining thelocation of the screw holes.

37 mm

3 Attach the motion sensor to therear cover.R Insert the grooves on the

motion sensor to the 4 tabs onthe rear cover, and then pushdown the motion sensor.

UP

Using the wall mounting adaptor

1 Remove the rear cover bypressing the upper sides of thecover (A) and then sliding it down(B).

A

B

13

Setup


2 Attach the wall mounting adaptorto the wall by using screws (1).R Place the wall mounting

adaptor with “UP” mark facingupwards.

R 2 21 mm

2

UP

1

1

3 Attach the motion sensor to thewall mounting adaptor.R Insert the grooves on the

motion sensor to the 4 tabs onthe wall mounting adaptor, andthen push down the motionsensor.

14

Setup


Testing the motionsensorYou can observe the motion sensor’sLED indicator and test the performanceof the motion sensor.1 Press M N.2 Move to an area near the motion

sensor.3 While moving near the motion

sensor, observe the LED indicator.R When motion is detected, the

LED indicator lights in red.4 Note the areas where movement

is detected.5 Press M N again.

Adjusting the sensorsensitivityYou can use the MHIGHN/MLOWN switch(page 7) to adjust the sensor’ssensitivity. If the sensor often makesincorrect detections, such as in areaswith frequent and substantialtemperature fluctuations, set the switchto the MLOWN position.Note:R When the switch is in the MLOWN

position, the sensor detection rangeis reduced by about half (comparedto when the switch is in the MHIGHNposition).

Features availablewhen using the[Home Network] appSome of the motion sensor’s featuresthat are available when using the[Home Network] app are listed below.For more information, refer to theUser’s Guide (page 15).– Alarm system

You can use the app to arm anddisarm the alarm system, confirmthe current status of the sensor, andview a log of previous events.

– Sensor integrationYou can configure the motion sensorto trigger other system events, suchas camera recording, turning on anelectric device (such as a lamp), etc.(Appropriate device required.)

– Telephone alertYou can configure the system to calla preprogrammed phone numberwhen the motion sensor is triggered.

Accessing the User’sGuideThe User’s Guide is a collection ofonline documentation that helps youget the most out of the [HomeNetwork] app.1 iPhone/iPad

Tap in the app’s home screen.Android™ devicesTap or press your mobiledevice’s menu button in the app’shome screen.

2 Tap [User’s Guide].

15

Appendix


Note:R Microsoft® Windows® Internet

Explorer® 8 and earlier versions arenot supported.

R Android 4.1 or later versions arerecommended.

R You can also access the User’sGuide at the web page listed below.

www.panasonic.net/pcc/support/tel/homenetwork/manual/

SpecificationsR Standards

DECT (Digital Enhanced CordlessTelecommunications)

R Frequency rangeDECT: 1.88 GHz – 1.90 GHz

R RF transmission powerDECT: Approx. 10 mW (averagepower per channel)

R Power sourceAA (LR6) Alkaline battery (2 ´ 1.5 V)

R Operating conditions0 °C – 40 °C

R Sensor detection methodPyroelectric infrared sensor (heatsensor)

R Heat sensor detection rangeHorizontal: approx. ±45°Vertical: approx. ±10°Distance: approx. 5 m (when thesurrounding temperature is approx.25 °C)

R Battery lifeApprox. 1 year (when motion isdetected 50 times a day and the

surrounding temperature is approx.25 °C)

R Dimensions (height ´ width ´depth)– With the rear cover attached:

Approx. 72 mm ´ 73 mm ´39 mm

– With the wall mounting adaptorattached:Approx. 72 mm ´ 73 mm ´61 mm

R Mass (weight)– With the rear cover attached:

Approx. 70 g, excluding thebatteries

– With the wall mounting adaptorattached:Approx. 77 g, excluding thebatteries

16

Appendix


Warranty (for New Zealand)Panasonic New Zealand undertakes to:

Repair or at its option, replace without cost to the owner, either for material or labour,

part which is found to be defective within two years of the date of purchase.

THIS EXPRESS WARRANTY DOES NOT COVER:

IF YOUR PANASONIC PRODUCT FAILS WITHIN THE

WARRANTY PERIOD:

Take it to the Authorised Panasonic Dealer from whom you purchased the product

will repair it (or arrange to have it repaired) during their normal business

enquiries regarding warranty or otherwise, please call – Customer

e Tel. No.: (09) 272 0178

NOTE: THIS EXPRESS WARRANTY IS OFFERED AS AN

BENEFIT AND DOES NOT AFFECT YOUR LEGAL

1) Pick up and delivery.

2) Batteries.

3) Repairs when the product has not been used in accordance with the Operating

Instructions Manual or has been modified.

4) Normal maintenance and cleaning as required in the product’s Operating

Instructions Manual.

5) Service calls to: a Correct the set up of the product

b Instruct you how to use the product

c Replace fuses or correct your building’s wiring

6) Damage to the product caused by accident, misuse or Act of God.

7) Repairs when the product has been dismantled, repaired, modified or serviced

by other than a Panasonic Authorised Dealer authorised to service that type of

product.

any

Centr

All

who

RIGHTS.

EXTRA

Support

hours.

17

Appendix


18

Notes


19

Notes


For your future referenceWe recommend keeping a record of the following information to assistwith any repair under warranty.

Serial No. Date of purchase(found inside the battery compartment)Name and address of dealer

Attach your purchase receipt here.

For AustraliaCustomer Care Centre Tel. No.: 132600or website www.panasonic.com/auFor New ZealandCustomer Care Centre Tel. No.: (09) 272 0178or website www.panasonic.com/nz

Sales Department:

1 Innovation Road, Macquarie Park NSW 2113, Australia

Sales Department:

18 Sir Woolf Fisher Drive, Highbrook, East Tamaki, Auckland,

New Zealand

Phone: (09) 272 0100

Fax: (09) 272 0137

1-62, 4-chome, Minoshima, Hakata-ku, Fukuoka 812-8531, Japan

© Panasonic System Networks Co., Ltd. 2015

*PNQX7355ZA**PNQX7355ZA*

PNQX7355ZA CC0315WK0 (E)


Documents

Home Network System Motion Sensor KX-HNS102AZ...Green, blinking Registration mode (You pressed and held M N) Off No battery power Note: R The LED indicator does not indicate sensor