HITS Quick Take Plus (HITS QT+) DSR4440 and OM2000 Configuration DocumentThis document is being generated for the initial deployments of the ARRIS DSR4440 Integrated Receiver Decoder into the HITS QT+ System architecture in order to support the HITS, DVB-S2, QSD1-6, Linear SD Services transition in 2016. The DSR4440 is fully compatible with the pre-transition modulation parameters with the appropriate transponder and service/map settings. The DSR4440 can be installed and configured upon receipt of the unit. When the HITS uplink modulation transitions to the new parameters, the DSR4440 configuration can be altered to the details included in this document.

Integration into an existing system The DSR4440 Operator Guide can be downloaded from the DSR’s own internal

webpage with information listed below. The Operator Guide can also be obtained from ARRIS Digital CM, or a simple Internet search for DSR4440 manual (or DSR4440 operator guide).o Please refer to installation details listed therein

Substitute current HITS QSD1 uplink parameters into the configuration methodology listed belowo Transponder 1, or 1430 MHz, 19.5:3/4:Combined; VCT ID 214, Channel

Number 195 (or MPEG Svc 51) Cabling: the DSR4440 Phoenix connector is different than previous HITS

QT+ DVRs. The Cable Modifications section details modifying the existing cable for use in the new configuration.

The Out of Band Modulator (OM) configuration is unchanged as a function of the HITS Linear SD Services transition. When the DSR cable connection is modified for use on the DSR4440, the DSR4440 can be connected to the OM.

DSR 4440 ConfigurationReference document: no. 365-095-26359 DSR4440 – DSR4460 Commercial Integrated Receiver / Decoder (IRD) Operator Guide is downloaded from the DSR itself. The DSR’s main page has a link named UserGuide. Please refer to the Operator Guide for remote configuration through a PC browser.

HITS Quick Take Plus (HITS QT+) DSR4440 and OM2000 Configuration Document 1

365-095-30226-x.3

This particular document will deal exclusively with the IRD’s front panel. Relate the information contained in this document to the IRD’s WebUI if the DSR will be configured remotely.

The unit’s default IP address is 192.168.0.100, the default subnet mask is 255.255.255.0, and the default gateway is 192.168.0.1. It is a good idea to change the unit’s IP address once the unit is powered on.

Browser: http://192.168.0.100 when the login dialog box appears, leave both fields blank and select OK.

Front Panel Menu Structure OverviewGet a feel for the button response. Press arrow keys ← or → to note that the cursor moves in a wraparound fashion. Exiting the menu left or right will bring you back in from the other side.

While on any Main Menu item, pressing [ENTER] will cause the cursor to enter that menu’s Menu Group which is a vertical menu structure. Press arrows ↑ or ↓ to moves the selections to the next Menu Group item. Here also, the cursor moves in a wraparound fashion. Vertical movement past the first or last item will cause the cursor to reenter the menu structure from the bottom or top, respectively.

The Menu Group items are in UPPERCASE. This is the entry and exit point of any of the vertical menu structures. When the cursor is next to the UPPERCASE menu group item, pressing [ENTER] will cause the cursor to go back to the Main Menu level. Pressing [ENTER] again causes the selection to go back to where the cursor exited the vertical menu structure. The user interface will retain the position from where you exited the Menu Group vertical submenu.

The lower left corner displays a symbolic representation of the valid key presses. It changes in real-time depending on where the cursor sits. E means, arrow buttons: up, down, left, right or [ENTER] are valid selections; E means, arrow buttons: up, down or [ENTER] are valid; E means, arrow buttons: left, right, or [ENTER] are valid. An invalid key press does nothing to the cursor (no movement).

DSR-4440 E → Install → Channel → IP → Status → Diag

Figure 1 Main Menu

HITS Quick Take Plus (HITS QT+) DSR4440 and OM2000 Configuration Document 2

365-095-30226-x.3

Factory ResetPresent in top level menu Install: press ← or → to select Install / press [ENTER]1 Press arrow ↑ or ↓ to select RESET

A. Press ← or → to select Reset Type / press [ENTER]B. Press arrow ↑ or ↓ to change No to Factory Defaults / press [ENTER] Note: After initialization, ALARM LED (red) will be lit.

Summary SetupAdvanced users can reference the following table to expedite the data entry. AMC 18 Transponders of focus: QSD 2, TP1, 1430 Vert and QSD 3/4,

TP5, 1350 Vert

REFERENCE PARAMETER User Guide Ref.Install > MANUAL TUNE > Mode / Xpnder: 5

Pgs. 20 -24

----Alternate Entry Mode ----Install >MANUAL TUNE > Mode / LFreq: 1350 MHzInstall > MODULATION / Mode DVBS2Install > MODULATION / Symbol 30.0 (this value is in Msps)Install > PORT ID = <RF connected to 0 or 1>

Mode = Auto

VCT 971

Pgs. 39 -41VCN 471----Alternate Entry Mode ----MPEG SELECT – Program 71

Alarm Trigger (in the Install Menu Group) No Auth (1) Pg. 52

(1) No Auth for Alarm is recommended

No Auth is the more useful alarm (No Signal will cause No Auth, but this Alarm must occur if the signal is present but the Authorization state is not present)

Table 1 Summary of Settings

Signal Input Setup1. After initialization the menu will default to the Main Menu.2. The cursor will be next to Install / Press [ENTER]

HITS Quick Take Plus (HITS QT+) DSR4440 and OM2000 Configuration Document 3

365-095-30226-x.3

3. Press arrow ↑ or ↓ to select MANUAL TUNEA. Press arrow ← or → to select Input / press [ENTER]B. Press arrow ↑ or ↓ to select Port 0 / press [ENTER] (whichever Port

has the RF connection)C. Press arrow ← or → to select Mode / press [ENTER]D. Press arrow ↑ or ↓ to select LFreq / press [ENTER]

1. Xpndr alternate entry mode , press arrow ↑ or ↓ to select Xpndr / press [Enter]Note: The LFreq column on the far right becomes a status

MANUAL TUNE

→Input →Mode →LFreq

E Port 0 LFreq 1350.00Figure 2 LFreq Entry Mode Causes ‘Xpndr’ to Disappear

MANUAL TUNE

→Input →Mode →Xpndr LFreq

E Port 0 Xpndr 05 1350.00Figure 3 Alternate Entry For ‘Xpnder’ Mode – LFreq becomes a Status

E. If using LFreq entry: Press arrow ← or → to select LFreq column / press [Enter]

F. Press arrow ← or → to select digit places; Press arrow ↑ or ↓ to select digit values. Set 1350.00 [Enter]1. If using Xpndr alternate entry mode,

press arrow ← or → to select Xpndr column / press [ENTER]2. If using Xpndr alternate entry mode ,

press arrow ↑ or ↓ to roll through the digit values. Set 5. [ENTER]G. Press arrow ← or → to select MANUAL TUNE / press [ENTER]H. Press arrow ↑ or ↓ to select MODULATION

Press arrow ← or → to select Mode, set to DVBS2 press [Enter]I. Press arrow ← or → to select Symbol, set to 30.0 press [ENTER]J. The SIGNAL LED on the front panel should now be GREEN

Virtual Channel or MPEG Information Setup1. From the Main Menu, press arrow ← or → to select Channel / press [ENTER]

A. Viewing the CHANNEL Menu Group, press arrow ← or → to select VCT / press [ENTER]If the entry mode will be VCT and Channel, please skip 1-4 below. Go down to section B.

HITS Quick Take Plus (HITS QT+) DSR4440 and OM2000 Configuration Document 4

365-095-30226-x.3

1. MPEG SELECT alternate entry mode – when viewing the CHANNEL Menu Group, press arrow ↓ to change Menu Group to MPEG SELECT.

2. Press arrow ← or → to select Program. Press [Enter]3. Press arrow ← or → to select digit places; Press arrow ↑ or ↓ to change

values. Set 71 / press [ENTER]4. Press arrow ← or → to select MPEG SELECT, press [ENTER] –there is

now no need to discreetly set the VCT and Channel. Go to section Alarm Configuration Setup

B. Press arrow ← or → to select digit places; Press arrow ↑ or ↓ to change values. Set 971 / press [ENTER]

C. Press arrow → to select Channel (not CHANNEL on the far left) / press [ENTER]

D. Press arrow ← or → to select digit places; Press arrow ↑ or ↓ to change values. Set 471 / press [ENTER]

E. The AUTHORIZED LED on the front panel should now be GREEN

Alarm Configuration Setup1. From the Main Menu, press arrow ← or → to select Install / press [ENTER]

A. Viewing the Install Menu Group, press arrow ↑ or ↓ to change to ALARMB. Press arrow ← or → to select Trigger, press [Enter]C. Press arrow ↑ or ↓ to change to No Auth, press [Enter]D. Press arrow ← or → to select ALARM, press [Enter] to return to the Main

Menu. No Auth is the more useful alarm trigger. No Signal will always cause a

No Auth condition, but the reverse is not true.

OM2000 ConfigurationThe OM2000 is only configured by way of the OM’s corresponding version Element Manager. The Element Manager is downloaded from the OM2000’s internal webserver. The IP address is present on the front panel. Connect a PC to download the Element Manager if needed. Older OM2000 Element Managers could show a Motorola logo (branding).

While OM2000 firmware versions have advanced for other reasons, and subsequently have modified the branding, older firmware OM2000s are being supported in HITS QT Plus (as of the date of this document).

HITS Quick Take Plus (HITS QT+) DSR4440 and OM2000 Configuration Document 5

365-095-30226-x.3

Physical Interface Configuration1. With the Configuration drop-

down menu, show in 2. Error: Reference source not

found, select Physical Interface Configuration –shown in Error: Reference source not foundA. Port 5: RS530

(This is the Isochronous Interface)

B. Serial Mode = Sync SlaveC. Data Rate = 1500000D. Port 6: RF ModulatorE. Modulation Mode = Operate

(CW Test can be used to simplify power adjustments)

F. RF Freq (MHz) = 75.25(this value is in units of MHz)

Error: Referencesource not found also shows an RF Modulator Output Level setting. This is not a specific value. The value displayed is an integer representation of a power level from 30 dBmV to 50dBmV. It is not a direct unit of power level. 1 = 30 dBmV, 40 = 50 dBmV; each number = .5 dBmV change

The OM Output Level is determined by the individual needs of

HITS Quick Take Plus (HITS QT+) DSR4440 and OM2000 Configuration Document 6

365-095-30226-x.3

Figure 4 Element Manager – Configuration Drop-Down

Figure 5 Element Manager – Physical Interface Configuration

the downlink. An initial setting of the Modulation Mode: “CW Test” (Continuous Wave: unmodulated carrier) can simplify power measurements. ARRIS and SCTE 40 recommend measurements using the analog service picture carriers as references (-10 dBc & -8 ± 5 dBc, respectively) –or the 64 QAM services (0 dBc & 0 ± 2 dBc, respectively).

Logical Ports ConfigurationLogical Port assignments are the method by which signals are interconnected and routed through the OM 2000. When a Logical Port is configured as an Input, the routing is completed with a PID Map Table entry (detailed in the next section).

Select Logical Ports Configuration with the Configuration drop-down menu. As seen in Figure 6, Logical (Log) Port assignments Index 1 to 16 get Physical Interfaces assigned. Notice that the Modulator physical port on Log Port Index 1, an output, has no PID Map Table selectable. PID Map Tables are used to interconnect an input to an output. Log Ports 2 and 3, inputs, have a selectable PID Map Table.

Figure 6 Element Manager – Logical Port Configuration

Logical Port Settings1. Logical Ports are designated as follows:

A. Log Port Index 01

HITS Quick Take Plus (HITS QT+) DSR4440 and OM2000 Configuration Document 7

365-095-30226-x.3

B. Physical Interface = 6:ModulatorC. Operation Mode = OutputD. Log Port State = Unlocked (if not already set)

E. Log Port Index 02F. Physical Interface = 7:PID GenG. Operation Mode = InputH. Log Port State = Unlocked (if not already set)

I. Log Port Index 03J. Physical Interface = 5:RS530K. Operation Mode = InputL. Log Port State = Unlocked (if not already set)

2. Select the [Apply] soft-button.A note regarding Log Port Index 4 – 16: The default out-of-the-box states of these ports are blank (no text entry). Any change to them must then be accompanied by the setting “Note Used” –if they are to remain undefined. They will never again be able to be set to blank. The Not Used setting can be either 4:Not Used or 8:Not Used as show in Figure 6.

PID Map TablesThe PID Map Table is the method for assigning a Logical Port input to a destination. It also has the ability to selectively remap, or filter, PIDs in the transport stream(s). The PID remap/filter feature is unused a QT Plus headend configuration.

As shown in Figure 6, the PID Map Table number corresponds to the (Logical) Log Port Index 02 or 03 (Table 02 or Table 03). Selecting the Table 02 soft-button opens its PID Map Table, as shown in Figure 7. The two PID Map Tables, 02 and 03, only differ in the window title block in the upper-left corner. The user settings in the table body will be identical.

Note that the rows in the PID Map Table are labeled as Index 1 – 16. In this window, the Index is nothing more than a row designation. It is the Table itself (Table 02, Table 03), that is the key to the Logical Port connection. The columns that are labeled (Destination) Destin Port 1, 2, or 3 are the three possible destination ports to which any Logical Port input can assigned.

HITS Quick Take Plus (HITS QT+) DSR4440 and OM2000 Configuration Document 8

365-095-30226-x.3

The PID Map Table for Logical Port 02 (Table 02) assigns Logical Port 02 to its Destin Port. This designation is 01, because the Modulator was assigned to Log Port Index 01 back in Figure 6. There is no PID remapping occurring in the QT Plus configuration, therefore row Index 1 gets this user entry.

Figure 7 PID Map Table screen for PID Map Log Port 2 (Table 2) and Log Port 3 (Table 3)

HITS Quick Take Plus (HITS QT+) DSR4440 and OM2000 Configuration Document 9

365-095-30226-x.3

PID Map Table Settings1. Table 02 / Index 1 / Destin Port 1 ; set the drop-down menu selection: 01 ; Select [Commit]2. Table 03 / Index 1 / Destin Port 1 ; set the drop-down menu selection: 01 ; Select [Commit]

OM2000 RebootRemoving the ISOC data cable from the OM2000 can possibly cause the MPEG processor to lose synchronization. The result is a lack of data processing even when the above settings have been configured and the cable is reconnected. If the configuration setting have been performed, and the OM2000 is not transmitting RF set top control data, reboot the OM from the Element Manager – System > Reboot. The DATA LED could still be Green. Use the set top On Screen Diagnostics to

confirm Out-of-Band data.

Cable Modifications

Figure 8 DB-25S Connector on Cable (Connector: D-type, 25 Sockets)

HITS Quick Take Plus (HITS QT+) DSR4440 and OM2000 Configuration Document 10

365-095-30226-x.3

PIN 1

DSR 4520X

DSR 4440 - 7 Pin connector(5 Pin shown for reference)Figure 9 Pin 1 Is not shown on Phoenix connectors (DSR4440 uses the supplied

7 pin)

Phoenix Connector Plug from Cable DB-25SDSR4520X DSR4550 DSR4440 (7 pin) Pin / Signal

1 GND 5 GND 5 GND 1 Shield/GND2 CLK+ 4 CLK- 3 C+ 17 RT3 CLK- 3 CLK+ 4 C- 9 RT Rtrn4 DATA+ 1 DATA+ 1 D+ 16 RXD Rtrn5 DATA- 2 DATA- 2 D- 3 RXD

6 no connect7 no connect

Phoenix Bulkhead DSR4440 RS-530 I/O OM2000Table 2 Cable Modifications - Pinouts

The Phoenix connectors shown below do not have Pin 1 marked. The subminiature connectors for the DSR4440 are designed to not

have a strain relief (Backshell)

HITS Quick Take Plus (HITS QT+) DSR4440 and OM2000 Configuration Document 11

365-095-30226-x.3

D-type (D-shell) connector is show for reference. The sockets are usually marked with pin numbers. A cell phone photograph can often catch the detail.

Help with your product is available online and by phone. Find technical documentation in the CustomerCare 360 Documentation Center (http://www.arrisi.com/cc360). Get release updates and download software from DigitalCM (digitalcm.arrisi.com). The ARRIS Training Learning Portal provides self-paced product training and course descriptions of instructor-led training classes at http://www.arris.com/support/training. In many cases training can be given at your location.The Technical Assistance Center (TAC) provides assistance 24 hours a day, 7 days a week. To open a case, use one of these contact methods: Customers in North American should call the TAC at 888-944-HELP (888-944-

4357). Customers outside North America should call the TAC at 215-323-2345. For Spanish language support, call 215-323-2346. Contact the TAC by e-mail at Tac.Helpdesk@arrisi.com

HITS Quick Take Plus (HITS QT+) DSR4440 and OM2000 Configuration Document 12

365-095-30226-x.3

ARRIS Enterprises, Inc. 3871 Lakefield Drive, Suwanee, GA 30024 www.arris.com

©ARRIS Enterprises, Inc. 2014 All rights reserved. No part of this publication may be reproduced in any form or by any means or used to make any derivative work (such as translation, transformation, or adaptation) without written permission from ARRIS Enterprises, Inc. (“ARRIS”). ARRIS reserves the right to revise this publication and to make changes in content from time to time without obligation on the part of ARRIS to provide notification of such revision or change.

365-095-30226-x.3 6/2016