If you can't read please download the document
Upload
ledung
View
221
Download
0
Embed Size (px)
Citation preview
2 1-800-700-5919 Visit our Web site at www.csunitec.com
Concrete and Masonry Tools
CS Unitec's Trelawny line of surface preparation tools features manyVibro-Lo models. These models include integrated vibration reductiontechnology to operate with 7x less vibration than standard models.Vibration damping components offset the hammer vibration when the toolimpacts the workpiece, reducing the risk of vibration-related injury.
Heavy-Duty Hand-Held Scabblers (Pneumatic) p. 5
Low-Vibration Single-Head and Triple-Head Scabbling Hammers
Roughen, reduce and level concrete; prepare cracks for repair
Optional vacuum shroud for dust extraction
Multi-Headed Floor Scabblers (Pneumatic) p. 6-7
Vibro-Lo 11-head model for concrete keying, laitance removal and less-aggressive material removal to protect substrate below
5-head model for fast concrete removal and demolition when leveling high spots, texturing and roughening for sealant/overlay preparation and breaking down hard coatings prior to blast cleaning
Vibro-LoVibration Reduction
Technology
Floor Scarifiers / Planers (Electric Pneumatic Gas) p. 8
Ideal for the most demanding surface preparation and material removal applications
Remove rust, scale, paint, adhesives and more from steel and concrete
Long-Reach Chisels / Scrapers / Scalers (Pneumatic) p. 14
Available in lengths ranging from 2' to 6'; chip, scrape and descale with one tool
Surface Preparation Tools & Dust Collection Vacuums
HEPA filtration for cleaner, safer work environment
"Power Take Off"outlet for ON/OFF activation from power tool switch
Standard wet/dry models available
Hand-Held Construction Scabblers (Pneumatic) p. 4
Dust Collection Vacuums with HEPA Filtration p. 15
Low-vibration hand-held and walk-behind grinders
5", 7"and 9" models
Concrete Grinders p. 15
Low-Vibration Single-Head and Triple-Head Scabbling Hammers
Roughen, reduce and level concrete
Prepare surfaces for coatings and finishes
Vibro-LoVibration Reduction Technology
Vibro-LoVibration Reduction Technology
Vibro-LoVibration Reduction Technology
Low-Vibration Needle/Chisel Scalers (Pneumatic) p. 10-13
Vibro-Lo Needle/Chisel Scalers remove coatings, corrosion and other accumulated materials
Clean and stress-relieve weld seams and joints
Variety of needles and chisels, including options for use in hazardous areas and Ex zones
Vibro-LoVibration Reduction Technology
GRINDER
S
SCARIFIER
S
CHISEL SCALERSCABBLER
Hand-Held Scarifiers Rotopeen (Pneumatic Electric) p. 9
Ideal alternative to small-area shot blasting clean/prepare steel and concrete surfaces
Available with 3M's Rotopeen 'C' flaps, star cutters and beam cutters
3 1-800-700-5919 Visit our Web site at www.csunitec.com
Core Drilling, Hammer Drilling, Mixing, Sawing & MoreWet / Dry Diamond Core Drills (Electric Air Hydraulic) p. 16-18Drill holes from 1/8" to 14" dia. in floors, walls and ceilings. Fast drilling of reinforced concrete, concrete, brick, block and stone. Wet/dry models with dust collection port. Water recycling and slurry containment vacuum.
Rotary Hammer Drills (Air Hydraulic) p. 19Powerful percussion for drilling concrete and masonry. SDS Plus and SDS Max chucks. Hammer drill holes in concrete, brick and masonry. Rotary drilling for straight drilling of steel and wood.
Mixing Drills and Mixing Stations (Electric Pneumatic) p. 20-21Professional variable-speed, high-torque models for fast, efficient mixing. Hand-held models for batches up to 5 bag/35 gallons. Variety of galvanized steel mixing paddles and portable mixing stands and stations for running mixers independently.
HIPPOMixing Station p. 21Mix, transport and pour with one unit. Casters or tires for varying jobsite terrain. Removable liner for mixing multiple batches and extending life of bucket.
Concrete Hand-Held and Walk-Behind Cut-Off Saws (Air) p. 22Wet or dry cutting of concrete, reinforced concrete, asphalt, masonry, steel and more. Low maintenance no belts, pistons, fuel lines or carburetors to maintain. Walk-behind saw designed for tough cutting jobs, including joint sawing, floor sawing, trenching, road repair and plant maintenance.
Concrete Circular Saw p. 22Wet or dry cutting of stone and masonry materials, including granite, marble, terrazzo and concrete. 7" blade, adjustable cutting depth up to 2-1/3". Vacuum connection.
Wall Slotter p. 22Cut channels up to 1-13/16" wide x 1-3/4" deep in concrete and masonry. Adjustable width and depth. Vacuum connection.
Concrete Chain Saws p. 23Pneumatic and hydraulic diamond concrete chain saws. Deep plunge cuts up to 20" deep and square corners up to 19" with no overcuts. Ideal for mechanical openings and irregular shapes. PowerGrit diamond pneumatic chain saw for ductile iron.
Stone Polishers p. 24Low-speed wet and dry models for stone, concrete, metal, plastic, glass and more.
WarrantyProducts of CS Unitec, Inc. are warranted to be free from defects in material and workmanship for one year from date of purchase. This warranty does not apply tonormal wear or products which have been abused, misused, modified or repaired by someone other than CS Unitec, Inc. or its Authorized Service Representatives.If a product proves defective in material or workmanship within one year after purchase, return it to CS Unitec, Inc. or an Authorized Service Center, transportationprepaid. CS Unitec, Inc. will, at its option, repair or replace defective products free of charge.CS Unitec, Inc.'s sole liability and your exclusive remedy under this warranty is limited to repair or replacement of the defective product. There are no other warrantiesexpressed or implied and CS Unitec, Inc. shall not be liable for incidental, consequential or special damages, or expenses excepting only the cost or expense of repairor replacement as described above.
SafetyOperators of any power tool should use appropriate safety precautions for work being performed. This includes safety chains, eye protection, hearing protection,gloves and more. Follow instructions included in operating manual.
CS UnitecsTrelawny Vibro-Lo Single-HeadScabbler operateswith 7x less vibrationthan standardmodels. This toolutilizes vibrationdamping componentsto offset the hammervibration createdwhen the headimpacts theworkpiece.
CSUnitecs Trelawny line of pneumatic hand-held constructionscabblers are ideal for roughing and reducing concrete surfacesto remove laitance and coatings and expose aggregate to allowfor proper application of new materials such as textured finishesand waterproofing coatings.
Single-head scabbler includes integrated Vibro-Lovibration reduction technology
Triple scabbler includes integrated back handle grip forcomfortable operation and control
Single-piece Tungsten Carbide Tipped pistons withCruciform or Bush heads
Roughen, reduce and level concrete; preparesurfaces for coatings and finishes
Applications include: Scabbling concrete to expose aggregate Leveling concrete and block joints Texturing, roughing and reducing concrete Preparing for coatings and waterproofing compounds Bridge maintenance
Hand-Held Construction Scabblers
Concrete scabblingusing single-head,
Vibro-LoScabbling Hammer
Scabbling Hammer AccessoriesPart No.
612.6000
612.6010
815.5550
859.1530
859.1555
For Model Numbers
151.6170 and 153.6050
161.6171 and 153.6051
151.6171 and 151.6170
153.6051 and 153.6050
Single-PieceCruciform Piston
Single-PieceBush Piston
Whip Check
Lubricators
Vibro-LoVibration Reduction
Technology
Vibro-Lo
Vibro-Lo
Triple Scabbler includesintegrated back handle gripfor operator comfort andcontrol.
Pneumatic Hand-Held Construction Scabbling Hammers
Pneumatic
TripleHead
Bush Hammer Piston
Cruciform Piston
Bush Hammer Pistons
Cruciform Pistons
153.6051
153.6050
10.5
10.5
19" x 8.6"
19" x 8.6"
8400
8400
16
16
98.5
98.5
41.6
41.6
151.6171
151.6170
6.5
6.5
19" x 6.2"
19" x 6.2"
2800
2800
12
12
98.5
98.5
4.6
4.6
Description
CruciformBush
ModelModel
NumberWeight(lbs.)
Dimensions(LxH)
Blows per
minuteCFM @90 PSI
Noise Leveldb(A)
VibrationLevelsm/s2
SingleHead
4 1-800-700-5919 Visit our Web site at www.csunitec.com
Heavy-Duty Hand-Held Scabblers
PneumaticCSUnitecs Trelawny line of pneumatic heavy-duty hand-held scabblers areideal for more demanding scabbling applications such as the removal of steelscale deposits and the preparation of concrete cracks for repair. These tools alsoreduce, level, texture and roughen concrete, remove coatings and laitance andscabble concrete to expose aggregate for the application of sealants and coatings.
CS UnitecsTrelawny Vibro-Lo Single-HeadHeavy-Duty Scabbleroperates with 7x lessvibration thanstandard models.This tool utilizesvibration dampingcomponents to offsetthe hammer vibrationcreated when thehead impacts theworkpiece.
Single-head heavy-duty scabbler includes integrated Vibro-Lo vibration reduction technology
Triple scabbler offers 7200 blows per minute Single-piece Tungsten Carbide Tipped pistons with
Cruciform or Bush heads Optional dust shroud for dust and debris collection
Ideal for more demanding concrete preparationand coating removal applications
Applications include: Removing steel scale deposits Prepare concrete cracks for repair Texturing, roughing, reducing and leveling concrete Scabbling concrete to expose aggregate Preparing for coatings and waterproofing compounds
Concrete scabbling usingsingle-head, Vibro-LoHeavy-Duty Scabbler
Heavy-Duty Scabbler AccessoriesPart No.
612.5320
612.5325
815.5550
859.1530
859.1555
437.5100
437.5300
For Model Numbers
151.5200, 196.5100
and 153.5200
151.5250, 196.5105
and 153.5250
Single-head Scabblers
Triple-head Scabblers
151.5200 and 151.5250
153.5200 and 153.5250
Single-PieceCruciform Piston
Single-PieceBush Piston
Whip Check
Lubricators
Vacuum Shroud*
Vibro-LoVibration Reduction
Technology
Vibro-Lo
Vibro-Lo
Pneumatic Hand-Held Construction Scabbling Hammers
Low-Vibration
Single Head
Triple Head
Bush Hammer Piston
Cruciform Piston
Bush Hammer Pistons
Cruciform Pistons
196.5105
196.5100
5.7
5.7
19" x 6.2"
19" x 6.2"
2900
2900
11.9
11.9
91
91
4.5
4.5
Bush Hammer Pistons
Cruciform Pistons
153.5250
153.5200
11.5
11.5
19" x 6.2"
19" x 6.2"
7200
7200
15.9
15.9
98
98
8.7
8.7
151.5250
151.5200
5.7
5.7
19" x 6.2"
19" x 6.2"
2400
2400
6.5
6.5
94
94
7.0
7.0
DescriptionModelModel
NumberWeight(lbs.)
Dimensions(LxH)
Blows per
minuteCFM @90 PSI
Noise Leveldb(A)
VibrationLevelsm/s2
SingleHead
* Not available for low-vibration models
Reduce dust andhazardous particles inwork area with optionalvacuum shroud forHeavy-Duty Hand-HeldScabblers (below).
See page 15 fordust extraction
systems.
5 1-800-700-5919 Visit our Web site at www.csunitec.com
Applications include: Concrete keying Laitance removal
Situations requiring gentle,effective scabbling withoutdamaging the substrate below
CSUnitecs Trelawny MHS11 Multi-Headed Concrete Floor Scabbleris a portable, compact, low-vibration machine that covers up to 100 sq. ft./hour.
CS Unitecs Trelawny MHS11 multi-headedconcrete floor scabbler operates with 7x lessvibration than standard models. This tool utilizesa 3-point mechanical vibration damping systemto offset the hammer vibration created when thehead impacts the workpiece.
Integrated Vibro-Lo vibrationreduction technology
24,000 light blows per minute
Built-in dust shroud for dust and debriscollection (model no. 159.6051)
Low air consumption
Concrete keying and laitanceremoval 11 heads provide24,000 light blows per minute
11-Head Floor Scabbler - MHS11 Vibro-LoVibration Reduction
Technology
Vibro-Lo
Vibro-Lo
MHS11 Low-Vibration Pneumatic Multi-Headed Concrete Floor Scabbler
With Dust Shroudand BushHammer Heads
With BushHammer Heads
159.6051
159.6050
158 11.25" x 13.5"x 50"
24,200 55 97 4.96
Model DescriptionModel
NumberWeight(lbs.)
10"
155 11.25" x 13.5"x 50"
24,200 55 97 4.9610"
CuttingWidth
Dimensions(WxLxH)
Blows per
minuteCFM @90 PSI
Noise Leveldb(A)
VibrationLevelsm/s2
MHS11
MHS11 Accessories Part No.
612.0125
426.5355
426.5358
612.0120
815.5550
859.1580
For Model Numbers
159.6050 and 159.6051
159.6000*
159.6100*
159.6000 and 159.6100*
* Call for details
One-Piece Piston TCT Bush Hammer Head
Replaceable TCT Bush Hammer Cutter Head
Replaceable TCT Cruciform Cutter Head
Piston for Replaceable Cutter Heads
Whip Check
Lubricators
Head Applications:
Bush Hammer Heads areideal for laitance removal;roughing concrete forresurfacing; bridge deckpreparation for waterproofing.
Cruciform Cutter Heads areideal for leveling floors,reducing concrete; removal offloor paints and coatings.Call for details on complete MHS 11 with Cruciform Heads.
Dust PortDust shroud, P/N437.0120, to collect dustand debris when connectedto a dust collectionvacuum. Included withmodel no. 159.6051
See page 15for dustextraction systems.
6 1-800-700-5919 Visit our Web site at www.csunitec.com
PneumaticMHS11
includes dustshroud andvacuum port
(Model no.159.6051)
Multi-Headed Floor Scabbler - MHS5
MHS5 Pneumatic Multi-Headed Concrete Floor Scabbler
MHS55-Point Bush Head
9-Point Bush Head
159.5050
159.5075
251
251
28" x 43" x 38"
28" x 43" x 38"
6500
6500
80
80
94.7
94.7
16.5
16.5
Model DescriptionModel
NumberWeight(lbs.)
11"
11"
CuttingWidth
Dimensions(WxLxH)
Blows per
minuteCFM @90 PSI
Noise Leveldb(A)
VibrationLevelsm/s2
Applications include: Leveling high spots Texturing and roughening for
sealant and overlay preparation
Breaking down hard coatings priorto blast cleaning
CSUnitecs Trelawny MHS5 Multi-Headed Concrete Floor Scabbleris the ultimate demolition tool for quick concrete removal.
6500 BPM for fast removal and demolition
Integrated dust shroud for dust and debris collection
Large wheels for rough terrain
Built-in dead mans handle
Fast concrete removal and demolitionwith integrated dust port
MHS5 Accessories Part No.
441.5360
441.5359
441.5369
815.5550
859.1580
Included
Cruciform Scabbler Head
5-Point Bush Hammer Head
9-Point Bush Hammer Head
Whip Check
Lubricators
Dust Shroud
Head Applications:
Cruciform Scabbler Heads are ideal for leveling floors, reducing concrete and removal of floor paints and coatings.
5-Point Bush Hammer Heads are ideal for laitanceremoval from large floor areas, roughing concrete prior toresurfacing and bridge deck preparation for waterproofing.
9-Point Bush Hammer Heads are ideal for levelinguneven joints and creating excellent bond profiles forepoxies, urethanes and thin overlays.
MHS5 includes integratedvacuum shroud and port.
See page 15for dustextraction systems.
7 1-800-700-5919 Visit our Web site at www.csunitec.com
Applications include: Removal of rust,
scale, paint, adhesives and more
Keyed or grooved profiles
Roughing concrete
CSUnitecs Trelawny Floor Planers tackle the most demandingsurface preparation and material removal applications. Ideal for theremoval of coatings and corrosion from concrete and steel surfacesto prepare for re-coating. Produce an ideal keyed or grooved profileon concrete for waterproofing and non-slip surface applications.
Depth control maximizes performance and extends cutter life
Integrated vacuum connection and hold-to-run handle
Fully adjustable handlebar for operator comfort
Electric, pneumatic or gas power
Remove rust, scale, paint, adhesivesand more from concrete and steel
Floor Scarifiers - Electric, Pneumatic and Gas
TFP 200 Floor Scarifiers
320.2004T
320.2012T
14" x 35" x 35"1/8"
Model NumberWeight(lbs.)
220V - 240V, 3 HP 8"
CuttingWidth
Dimensions(WxLxH)
Max CuttingDepth per Pass
TFP 200 Electric
14" x 35" x 35"1/8"165CFM @ 90 PSI, 3.5 HP
Motor Specifications
8"
149
99
TFP 200 Pneumatic
320.2000T 14" x 35" x 35"1/8"Honda GX160 Gas, 5.5 HP 8" 130
TFP 200 Gas
TFP 200 Cutters IndividualCutter
N/A
320.5120
320.3658
320.5500
320.5600
320.5650
320.5500
DrumAssembly
320.9620
320.1020SB
320.1020SS
320.1020ST
320.1020SM
320.1020SM
320.1020G
Wire Brushes
Beam Cutters
Star Cutters
Tungsten Carbide Tipped Cutters
Milling Cutters (22mm)
Milling Cutters (11mm)
Tungsten Carbide Tipped Cutters(for grooving)
Cutter Applications:
Wire Brushes are ideal for finishcleaning and polishing on steel; canbe used for light concrete deposit.
Beam Cutters are ideal for lightpaint/corrosion removal, withminimal damage to substrate.
Star Cutters are ideal for theremoval of mastics and rubberizedcoatings.
Tungsten Carbide Tipped Cutters are ideal for aggressiveapplications such as roughing concrete and heavy corrosion removal,as well as grooving roadways for non-slip surface.
Milling Cutters are ideal for the removal of plastic road markingswithout penetrating the surface.
TFP 200Electric
TFP 200Pneumatic
TFP 200Gas
8 1-800-700-5919 Visit our Web site at www.csunitec.com
Star Cutter Beam Cutter 3M Rotopeen 'C' FlapP/N 312.S200 P/N 312.R200 P/N 312.MRPC
CSUnitecs Trelawny Rotopeen hand-held scarifiersare the ideal alternative to small-area shot blasting forcleaning and preparing concrete and steel surfaces.
Pneumatic and electric models
Integrated dust shroud for dust and debriscollection, as well as cleaner, safer removalof lead-based paints and contaminatedparticles
Peening preparation ideal alternativeto small-area shot blasting
Pneumatic Hand-Held Scarifiers
194.0205
194.C205
194.0405
194.C405
30
30
30
30
2700
2700
2700
2700
3.5
6.0
3.1
4.6
ModelNumber
CFM @90 PSI
Speed(RPM)
2"
2"
4"
4"
CuttingWidth
'C' Flaps
Star Cutters
'C' Flaps
Star Cutters
These models are compatiblewith Star Cutters, Beam Cutters
and Rotopeen 'C' Flaps
CuttingMedia
7.5
11.5
9
13.25
Weight(lbs.)
VibrationLevels m/s2
Electric Hand-Held Scarifiers
195.1215
195.1220
110V
220V
2000
2000
3.6
3.6
ModelNumber Motor Power
Speed(RPM)
2"
2"
CuttingWidth
'C' Flaps
'C' Flaps
CuttingMedia
10
10
Weight(lbs.)
VibrationLevels m/s2
Hand-Held Scarifier Accessories
HEAVYSCALING
LIGHTBURNISHING
Applications include: Aggressive removal of alkyds,
adhesives, lead-based paints, mastics,coatings corrosion and more
Cleaning and preparing concrete andsteel surfaces
Nuclear
Ships decks
Construction
Factory Floors
Swimming Pools
Bridge Maintenance
Pipeline Maintenance
Non-slip coatings
Plaster removal
Adhesive removal
Sealant removal
Ceiling / wall paint removal
Floor marking removal
Adhesive removal
Radioactive waste removal/capture
General paint removal
Ceiling / wall paint removal
Floor marking removal
Paint / sealant removal
Protective coating removal
Aggressive removalof thick coatings
Removal of hard coatings, lessaggressive than star cutter
Removal of light paint and rust to bare metal finish
Star CutterCuttingWidth
2"4"
QuantityRequired
80160
Beam CutterCuttingWidth
2"4"
QuantityRequired
56112
Rotopeen'C' Flap
CuttingWidth
2"4"
QuantityRequired
612
Electric Model 195.1220 2" cutting width with Rotopeen 'C' flaps
Pneumatic Models 194.0405 and194.C405, 4" cutting width
Hand-Held Scarifiers - Pneumatic and Electric
See page 15for dustextraction systems.
9 1-800-700-5919 Visit our Web site at www.csunitec.com
VL223
VL203
CSUnitecs Trelawny line of Low-Vibration needle/chiselscalers offer high performance and low vibration forgreater productivity and improved operator comfort.Ergonomically designed with low maintenance and quickchange tooling option.
CS Unitecs Trelawny Vibro-Lo line of Needle/ChiselScalers operate with 7x lessvibration than standard models.These tools utilize vibrationdamping components to offsetthe hammer vibration createdwhen the needles/chisels impactthe workpiece.
Integrated Vibro-Lo vibration reduction technology
Lightweight, easy to handle
Optional dust shroud for dust and debris collection
Tool-free needle changeover
Converts to chisel scaler in seconds
High power with low vibration equipped with Vibro-Lo
Applications include: Texturing concrete
Cleaning and stress-relieving weld seams and joints
Removing coatings, corrosion and other accumulated materials
Splitting, chipping, pointing and brick raking
VL303
Low-Vibration Needle/Chisel Scalers Vibro-LoVibration Reduction
Technology
Needle Scalers andChisel Scalers convert inseconds with optional
head or when purchasedas a Kit. See following
page for Kit information.
10
Low-Vibration Needle/Chisel Scalers
Chisel for light surface marking
Flat for light treatmentand polishing effect
Pointed for veryhard scale
Copper Berylliumfor use in potentiallyexplosive areas
Stainless Steel for usein applications wherecorrosion or humidity is aproblem, such as thefood processing industry
See page 13 for thefollowing types ofneedles:
Chisels for Vibro-Lo Chisel Scalers
Dust Collection Shroud for Vibro-Lo Needle Scalers
Shank Length Width Application
Pistol
VL223 Needle Scaler
VL223 Needle Scalerwith dust shroud
Chisel Part Number
Square
SquareCranked End
Square
Square
Square
7"
7"
7"
7"
10"
2"
3/8"
3/4"
2-1/2"
3/4"
Spark-resistant Aluminum Bronzefor use in hazardousareas
Weld flux and thick coating removal
Weld splatter removal
Wide flat chisel forthe removal of rustor peeling paint
Flat chisel for weldsplatter and sand cast cleaning
704.3110
704.3205
704.3101
704.3103
704.3107
DescriptionGripModel
Number
Needle Quantity/Diameter
Weight(lbs.)
Blows per
minuteCFM @90 PSI
Noise Leveldb(A)
VibrationLevelsm/s2
Optional Dust Shroud for Needle Scalers for use with dust extraction vacuums.
Model VL223 Needle Scaler Order Dust Shroud P/N 418.2003
Model VL203 Needle Scaler Order Dust Shroud P/N 418.2003
Model VL303 Needle Scaler Order Dust Shroud P/N 418.3003
VL223 Kit Order P/N 199.2113VL203 Kit Order P/N 199.2013VL303 Kit Order P/N 199.3103
CSUnitec offers Vibro-Lo Needle/Chisel Scaler Kits, each supplied with the Needle Scaler, 3mm needles, a chisel holder, anvil and a 3/4" blade chisel.
Vibro-Lo Needle Scalers
Vibro-Lo Chisel ScalersVibro-Lo Needle/Chisel Scaler Kits
CSUnitec offers a drop protection kit for our Vibro-Lo Needle/ Chisel Scalers. Protect your investment when working at heights or in applications where dropping/losing the tool is likely, including: offshore platforms and rigs, bridges/ scaffolding, vessels and ships.
For VL223 and VL203Order P/N 720.2003*
For VL303Order P/N 720.3003*
* Safety clip and line not supplied
Drop Protection Kit
Inline
Pistol
VL223 Chisel Scaler
VL203 Chisel Scaler
VL303 Chisel Scaler
199.2213
199.2203
199.3203
6.5
7
9.5
2400
2400
3000
4
4
5.5
76.3
76.3
78.2
3.69
3.33
3.7
DescriptionGripModel
NumberWeight(lbs.)
Blows per
minuteCFM @90 PSI
Noise Leveldb(A)
VibrationLevelsm/s2
Inline
H
H
199.2103
139.2103
199.2003
139.2003
199.3003
139.3003
19 / 3mm
19 / 3mm
19 / 3mm
19 / 3mm
28 / 3mm
28 / 3mm
5.25
5.25
6
6
7.75
7.75
2400
2400
2400
2400
3000
3000
4
4
4
4
5.5
5.5
90.7
90.7
90.7
90.7
109.5
109.5
2.56
2.56
2.75
2.75
2.3
2.3
VL203 Needle Scaler
VL203 Needle Scalerwith dust shroud
VL303 Needle Scaler
VL303 Needle Scalerwith dust shroud
CS Unitecoffers a fullline of non-sparking,non-magneticchisels andsafety handtools forhazardousareas and Exzones.Contact usfor details.
Vibro-LoVibration Reduction
Technology
See page 15for dustextraction systems.
11 1-800-700-5919 Visit our Web site at www.csunitec.com
Standard Needle/Chisel Scalers
1-800-700-5919 Visit our Web site at www.csunitec.com12
Chisel for light surface marking
Flat for light treatmentand polishing effect
Pointed for veryhard scale
Copper Berylliumfor use in potentiallyexplosive areas
Stainless Steel for usein applications wherecorrosion or humidity is a problem, such as the food processing industry
See page 13 forneedles:
Chisels for Standard Chisel Scalers1/2" Square Connection
Shank Length Width Application
Pistol
SemiPistol
1B Needle Scaler1B Chisel Scaler
2B Needle Scaler2B Chisel Scaler
Square
SquareCranked End
Square
Square
Square
Square
Square
7"
7"
7"
7"
10"
8"
7"
2"
3/8"
3/4"
2-1/2"
3/4"
1/4"
Moil Point
Spark-resistant Aluminum Bronzefor use in hazardous areas
Weld flux and thick coating removal
Weld splatter removal
Wide flat chisel for the removalof rust or peeling paint
Flat chisel for weld splatterand sand cast cleaning
Mortar removal for repointingbrick work
Concrete chipping
704.1110
704.2105
704.1101
704.1103
704.1107
704.1106
704.1112
DescriptionGripModel
NumberNeedle
Qty./Dia.Weight(lbs.)
Blows per
minuteCFM @90 PSI
Noise Leveldb(A)
VibrationLevelsm/s2
Dust Collection Shroud for Standard Needle ScalersOptional Dust Shroud for Needle Scalers for use with dust extraction vacuums.
Model 2B and 2BPG Needle Scalers Order Dust Shroud P/N 418.2199
Model 3BPG Needle Scaler Order Dust Shroud P/N 418.3039
* 3BPG Chisel Scaler 135.3395 has 5/8" hexagonal chisel holder and is compatible with chisels shown on page 14. All others Chisel Scalers shown above have 1/2" square connection.
Standard Needle and Chisel Scalers
TVS Needle Scalers with Integrated Vacuum Shroud
Inline
H
H
12 / 3mmN/A
19 / 3mmN/A
3.53.3
5.754.4
38003800
30003000
3.03.0
5.55.5
110.498.9
113.398.6
8.58.2
9.317.4
123.2199125.2300
133.3199135.3300135.3395
19 / 3mmN/A
28 / 3mmN/AN/A
5.754.5
8.256.26.2
30003000
220022002200
5.55.5
8.08.08.0
113.398.6
114.5105.1105.1
12.622.4
18.925.625.6
131.3099134.3200
141.4099144.4200
28 / 3mmN/A
35 / 4mmN/A
107.5
12.58.2
22002200
18001800
8.08.0
8.58.5
114.5105.1
117.4105.1
2BPG Needle Scaler2BPG Chisel Scaler
3BPG Needle Scaler3BPG Chisel Scaler3BPG Chisel Scaler*
3B Needle Scaler3B Chisel Scaler
4B Needle Scaler4B Chisel Scaler
Pistol
2B Needle Scaler
DescriptionGripModel
NumberWeight(lbs.)
Blows per
minuteCFM @90 PSI
Noise Leveldb(A)
VibrationLevelsm/s2
Inline 139.2007 6.4 3000 5.5 98.6 17.4
139.2107
139.3107
6.6
9.9
3000
2200
5.5
8.0
98.6
105.1
22.4
19.9
2BPG Needle Scaler
3BPG Needle Scaler
CS Unitec's Trelawny TVS Needle Scalers with Integrated VacuumShroud enable dust-free working in hazardous applications when usedwith a dust extraction vacuum (see page 15 for dust collection systems).
Pistol Grip
Semi PistolGrip
Above: Model 1B Chisel Scalerwith Square Cranked End Chisel
for removal of flux
CS Unitec offers afull line of non-sparking, non-magnetic chiselsand safety handtools for hazardousareas and Exzones. Contact usfor details.
Standard Needle Scalers and ChiselScalers convert in seconds with optional
head or when purchased as a Kit.Contact us for more information.
111.1099114.1200
121.2099124.2200
Inline Grip
12.219.9
23.545.2
Chisel Part No.
Available in 3mm flat tip only; for use in potentiallyhazardous areas.
Needles
Flat Tip
2mm
2mm
2mm
2mm
2mm
3mm
3mm
3mm
3mm
3mm
3mm
4mm
4mm
4mm
4mm
3mm
3mm
6 x sets of 29 needles
6 x sets of 51 needles
6 x sets of 65 needles
Box of 100 needles
Box of 2000 needles
6 x sets of 12 needles
6 x sets of 19 needles
6 x sets of 28 needles
6 x sets of 49 needles
Box of 100 needles
Box of 1000 needles (180mm long)
6 x sets of 19 needles
6 x sets of 35 needles
Box of 50 needles
Box of 500 needles
Box of 1000 needles 5" long (127mm)
19 x needles 5" long (127mm)
412.1129
412.1151
412.1165
452.1110
442.1107
413.1112
413.1119
413.1128
413.1149
453.1110
443.1107
414.1119
414.1135
454.1105
444.1107
443.1105
443.1115
Flat-tipped needles will reduce markingon metal surfaces and can give apolishing effect. For use on thin gaugemetals and any surface where a lighttreatment is required.2mm needles used on a welded joint produce a similareffect to shot peening, reducing stress in the weld.
Size Description Part #
Chisel Tip
3mm
3mm
3mm
3mm
3mm
3mmConversions:2mm = 0.08"
3mm = 0.12"
4mm = 0.16"
180mm = 7"
6 x sets of 12 needles
6 x sets of 19 needles
6 x sets of 28 needles
6 x sets of 49 needles
Box of 100 needles
Box of 1000 needles
413.2112
413.2119
413.2128
413.2149
453.2110
443.2107
These needles will clean the samematerials as a pointed tip, but will leavelight surface marking
Size Description Part #
CS Unitecs Trelawny needles last 10x longer than standardneedles. Save time and money with fewer needle changes and less downtime.
All of CS Unitecs Needle Scalers are delivered from stock completewith 180mm long x 3mm diameter chisel-tipped high-performanceneedles. Other needle holders are available as accessories for usewith 2mm and 4mm diameter needles. We also offer spark-resistantneedles for use in potentially hazardous areas and Ex zones, as well as stainless steel needles for usein humid areas such as applications in the food processing industry where corrosion is a concern.
Standard pack set is one carton of 6 sets. Some models are packed as an individual set in a box. Boxes of 100 qty. needles in a durable, reusable plastic container are available, as well as larger quantities.
Pointed Tip
3mm
3mm
3mm
3mm
3mm
3mm
4mm
4mm
4mm
4mm
6 x sets of 12 needles
6 x sets of 19 needles
6 x sets of 28 needles
6 x sets of 49 needles
Box of 100 needles
Box of 1000 needles
6 x sets of 19 needles
6 x sets of 35 needles
Box of 50 needles
Box of 500 needles
413.3112
413.3119
413.3128
413.3149
453.3110
443.3107
414.3119
414.3135
454.3105
444.3107
Sharpened to a conical point, these arethe most effective in breaking throughvery hard scale on materials where somesurface indentation is permissible or where a roughening or keying of the surface is actually desirable.
Size Description Part #
3mm
3mm
3mm
3mm
3mm
3mm
Box of 12 needles
Box of 19 needles
Box of 28 needles
Box of 49 needles
Box of 100 needles
Box of 500 needles
403.1312
403.1319
403.1328
403.1349
453.1310
443.1307
Size Description Part #
Spark-Resistant Copper BerylliumH
Available in 3mm flat tip form only, to be used inapplications such as refurbishment of food processingmachinery or areas of high humidity where the corrosiveeffect on needles would be prohibitive.Used on decorative concrete surfaces where contamination of thesurface from carbon steel needle is undesirable.
3mm
3mm
Box of 100 needles
Box of 500 needles
453.1207443.1207
Size Description Part #
Stainless Steel
1-800-700-5919 Visit our Web site at www.csunitec.com
See page 15fordust extraction
systems.
13
Long-Reach Chisels/Scrapers/Scalers
1-800-700-5919 Visit our Web site at www.csunitec.com
Long-Reach Chisels/Scrapers
StandardScalers
LITEScalers
2ft. Chisel4ft. Needle4ft. Chisel5ft. Chisel
4ft. Chisel5ft. Chisel6ft. Chisel
136.3299137.3499136.3499136.3599
136.3497136.3597136.3697
8111112
6.757.58.5
2200220022002200
220022002200
Model DescriptionModel
No.Weight(lbs.)
4.54.54.54.5
4.54.54.5
841048486
898984
CFM@ 90PSI
Blows per
minute
Noise Leveldb(A)
Chisel Accessories
Needle Scaler Accessories
Scraper Accessories
Ice Residue Adhesive Asbestos Linoleum Carpeting Plaster
Mortar Floor tiles Metal slag Rubber coatings Roofing materials Chemical spillages Bituminous products
Applications include removal of:
CSUnitecs Trelawny Long-Reach Scrapersfeature one tool with multiple applications.
Available in 2', 4', 5' and 6' lengths Three tools in one chipper, scraper and descaler Quick-change chisel release Low air consumption Standard and "LITE"models
Chip, scrape and descalewith one versatile tool
Chipping Scraping Descaling
705.1100
705.1101
705.1102
705.1106
705.1112
705.2102
708.1101
9"
9"
8"
9"
8"
8"
1"
2"
1"
4"
2"
4"
4"
1-1/8" comb insert
Spark-resistant aluminum bronzefor use in hazardous areas
Flat chisel for sand cast chipping
Asphalt cutter / paint removal /general chipping applications
Removal of linoleum from floor base
Spark resistant aluminum bronzefor use in hazardous areas
Floor tile removal
Brick cleaning and reclamation (usewith 8" long comb holder 708.1100)
ChiselPart No.
ChiselLength
Blade Width Applications
H
H
All long-reach scrapers are available as needlescalers by changing the scraper/chisel with theneedle attachment P/N 415.3532. See page 13for needles.
Flat
431.3504
431.3508
431.3512
Beveled
431.3904
431.3908
431.3912
439.3504(5 Blades)
439.3508(5 Blades)
439.3512(4 Blades)
439.3524(5 Blades)
439.3528(5 Blades)
439.3522(4 Blades)
Adhesive andpaint build up
removal
Paint andcoatingspillageremoval
Carpet andtile removal
Stubbornadhesiveremoval
Carpet andtile removal
Adhesiveremoval
4"
8"
12"
4"
8"
12"
ScraperAssemblyPart No.
BladePack
BladeWidth
Applications
14
Model CS 1435 H(shown at left)
automatically"pulse" cleansfilters withoutinterruptingoperation!
Vibration reduction technology Remove paint, epoxy, glue and other hard coatings Smooth rough surfaces Clean concrete before applying new paint or coatings Collect dust for clean working area with a CS Unitec dust extraction vacuum
1-800-700-5919 Visit our Web site at www.csunitec.com
Low-Vibration Hand-Held and Walk-Behind Grinders
Model No.
10,000
10,000
9,500
10
12
18
5"
5"
7"
14
16
20
EBS 125.5 D
EBS 1802 D
EBS 180 H
MotorPower (Amps)
GrindingCapacity
LoadSpeed (RPM)
Weight(lbs.)
5" dia. EBS 125.5 D 7"dia. EBS 180 H5"dia. Heavy-duty EBS 1802 D
1,380 849" 20 EBS 235
Hand-held Grinders
Optional Walk-behind Carts:for EBS 125.5 - P/N 37210for EBS 180 H - P/N 37217
Diamond Grinding WheelsUncoated
General Use (clear) Concretefor EBS 125.5 253 115 253 115 Cfor EBS 1802 D 253 115 253 115 Cfor EBS 180 H 253 117 253 117 C
Diamond Plate/Inserts for EBS 2359" Base Plate - P/N 37120 EDiamond Inserts (Gold) - P/N 37122 E (5 pieces per set)Diamond Inserts (Yellow) - P/N 37123 E (5 pieces per set)PCD Diamond Inserts (Black) - P/N 37121 E (5 pieces per set)
Optional Filter BagsPaper filter bags for CS 1225 and CS 1435 - P/N 416014 (5-pack)Plastic filter bags for CS 1225, CS 1435 and CS 1500 - P/N 421742 (5-pack)Paper filter bags for CS 1500 - P/N 416021 (5-pack)Slurry filter bags for CS 1500 - P/N 420592 (3-pack)
9" dia.EBS 235
Walk-behind Grinders
7" EBS180 Hwith Walk-Behind Cart
CS 1225 H
CSUnitecs dust extraction vacuums offer strong 130 CFMair flow and an electromagnetic pulse filter cleaning system to maximize vacuum power and dust collection.
Ideal for use with power tools
99.999% HEPA filtration efficiency of particlesdown to 0.3 microns; automatic filter cleaning
"Power Take Off" outlet activates the vacuum ON/OFF from the power tool switch
Non-HEPA models available, 99.930% filtration efficiency
Kit available to connect two power tools (P/N 198804)
Dust CollectionVacuums with HEPA Filtration
"PowerTake Off"
outlet
HEPA VacuumSpecifications
CS1225 H CS1500 H
Power 11 Amp 11 Amp 11 Amp
Air flow 130 CFM 130 CFM 130 CFM
Tank capacity 6.6 gal. 13 gal. 6.6 gal.
Weight 24.3 lbs. 35.2 lbs. 24.3 lbs.
Filter P/N (2pk.) 419190 419190 419190
CS1435 H
Standard VacuumSpecifications
CS1225 CS1500
Power 11 Amp 11 Amp 11 Amp
Air flow 130 CFM 130 CFM 130 CFM
Tank capacity 6.6 gal. 13 gal. 6.6 gal.
Weight 24.3 lbs. 35.2 lbs. 24.3 lbs.
Filter P/N (2pk.) 416069 416069 416069
CS1435
15
We make no claim that use of a vacuum will eliminate contaminants. Wear an approved respirator mask and follow all appropriate OSHA safety regulations forproper ventilation, dust handling, eye protection, etc. when using a dust extraction grinder and vacuum.
Concrete Grinders and Dust Collection Vacuums
16 1-800-700-5919 Visit our Web site at www.csunitec.com
3-speedEBM 350/3 P (motor only, foruse with compatible stands)EBM 350/3 PSA (anchor stand)EBM 350/3 PSV (anchorvacuum stand)
Drill holes up to 14"
END 130/3POSV
Wet/Dry - 2-speedETN 2001 PETN 2001 PSAETN 2001 PSVDrill holes up to 4"
END 712 P
END 1550 P
ETN 2001 P
ETN 162/3 P
END 130/3 PO
EBM 350/3 P
DBE 160
Model No.
Drill holes from 5/32" to 14" dia. in floors, walls and ceilings Fast drilling of reinforced concrete, concrete, brick, block and stone 5/8" and 1-1/4" standard thread connections Drills are equipped with a "slip clutch" Wet/Dry models have dust collection port
Wet and Dry Diamond Core Bits available for concrete, stone, asphalt andmore. Contact us for details.
0-8000
1800-4400
0-800/0-1570
0-510/0-1150/0-2500
600/1300/2800
230/500/1030
700
5
7
15
15
16
28
34**
5/32" to 1-3/8"
1/4" to 2-5/8"
up to 4"
up to 6"
up to 6"
up to 14"
up to 6"
6.3
13
15
19
15
24.5
18
MotorPower (Amps)
DrillingDiameter
Load Speed (RPM)
Weight(lbs.)*
Drill with Anchor Stand
Model No.
Drill with AnchorStand & VacuumPump Model No.
Wet
Hand-Held and Rig-Mounted Core Drills
Wet and Dry Diamond Core Drills - Electric
Wet - 3-speedEND 130/3 POEND 130/3 POSAEND 130/3 POSVDrill holes up to 6"
N/A
N/A
ETN 2001 PSA
ETN 162/3 PSA
END 130/3 POSA
EBM 350/3 PSA
Included
N/A
N/A
ETN 2001 PSV
ETN 162/3 PSV
END 130/3 POSV
EBM 350/3 PSV
N/A
* Weight is for hand-held models only. Please contact CS Unitec for weight information on drill rig combinations.** Weight is for the complete drill rig.
END712 PMini Diamond Drill for tile,natural stone and concrete
Drill holes 5/32 to 1-3/8"
0-8000 RPM1-speedDBE 160Rig-mounted
Drill holes up to 6"
Note: Hand-held core drills are intended up to a max. of 3" dia. for hand-held drilling or up to 6" dia. with a stand.
Wet/Dry - 3-speedETN 162/3 PETN 162/3 PSAETN 162/3 PSVDrill holes up to 6"
END 1550 PIdeal for stone, tiles,ceramic, porcelain,stoneware, glass, reinforced concrete and more
Drill holes up to 2-5/8"
1400-4400 RPM
Swivel anchor stand available:BST50V
Wet
17 1-800-700-5919 Visit our Web site at www.csunitec.com
EHD 1300 EHD 2000
Drill holesup to 5"
Drill holesup to 3-1/4"
Power
Water Capacity
Pump Output
Water Lift
Water Pressure
Air Flow
Canister Volume
Canister
Dimensions
Weight
Slurry Filter Bags
17 Amp, 115 VAC/60Hz
7 gallons
78 GPM at ground level
18 ft. max. discharge height
14.5 PSI (pump delivery)
150 CFM
13 gallons
Stainless steel tank with cart
20.5" W x 21.6" L x 39.5" H
59 lbs.
P/N 420592
CS 2000
Water Recycling and Slurry Containment Vacuum
Ideal for wet-working tools such as diamondcore drills, tile saws and wet grinders
Slurry and debris are contained in filter bag
Continuous loop system returns clean waterback into the vacuum for delivery back tothe tool
Can also be used as a regular wet/dryvacuum and to pump water from onelocation to another
Hand-Held Dry Core Drilling
EHD 1300
EHD 2000
12
15
up to 3-1/4"
up to 5"
0-2000
0-1000/0-2000
7
13
Model No.
MotorPower (Amps)
DrillingDiameter
Load Speed (RPM)
Weight(lbs.)
Water Collection Rings
Part No. Description35875 Water Collection Trap Ring for BST 104/60 V3587A Water Collection Trap Ring for BST 162 V35879 Water Collection Trap Ring for BST 300 and BST 300 V35849 Water Collection for Hand-Held Drilling (ETN 2001 P)35847 Water Collection for Hand-Held Drilling (END 130/3PO and ETN 152/3P)255.036 Water Collection for Hand-Held Drilling (2 1320, 2 1333, 2 1335 and 2 1317)
CS2000 shown with END 130/3POSV Core Drill and WaterCollection Ring.
Dry Diamond Core Drills and Stands
BST 104/60VAnchor VacuumStand, 30" high,
21 lbs.
BST 300 VAnchor VacuumStand, 44" high,
50 lbs.
BST 162 VAnchor VacuumStand, 38" high,
31 lbs.
BST 300Anchor Stand,
44" high,45 lbs.
BST 85Anchor Stand,
31" high,16 lbs.
Core Drill Stands
360 swivelrange
BST 50VAnchor Stand,
17" high,16 lbs.
Model2 1327 0010 SA
2 1333 0010
2 1333 0010 SA
2 1333 0010 SV
2 1335 0010
2 1335 0010 SA
2 1335 0010 SV
2 1328 0050 SA
2 1328 0050 SV
Model No.
77
77
77
123
123
123
123
123
3"
6"
6"
3"
6"
6"
12"
12"
2.1
2.1
2.1
3.8
3.8
3.8
3.8
3.8
MotorPower (HP)
Max.Drilling
Dia.CFM@90 PSI
18
49
51
21
52
54
66
72
Weight(lbs.) Stand
N/A
Anchor Stand
Anchor Stand & Vacuum Pump
N/A
Anchor Stand
Anchor Stand & Vacuum Pump
Anchor Stand
Anchor Stand & Vacuum Pump
Note: Hand-held core drills are intended up to a max. of 3" dia. for hand-held drilling or up to 6" dia. with a stand.
400/900/1600
400/900/1600
400/900/1600
300/700/1350
300/700/1350
300/700/1350
300/700/1350
300/700/1350
18 1-800-700-5919 Visit our Web site at www.csunitec.com
Model 2 1317 0030
Rugged 3-speed gearbox with mechanical slip clutch
Ideal for heavy-duty wet drilling in concrete, reinforced concrete and asphalt
Self-regulating oil flow control required volume of 6 GPM; flow up to 13 GPM is automatically bypassed back to the tank
Hose diameter: 1/2" ID Hose with 3/8" FF (HTMA) Couplings
Wet Diamond Core Drills - Hydraulic and Air
Hydraulic Core Drills
Model 2 1328 0050 SA
Model 2 1333 0010
Pneumatic Core Drills
Power Packs
Ideal for use with ourhydraulic power tools
Delivers 5 GPM or 8 GPM at 2000 PSI
Easy to move with liftand latch handle
Weighs 330 lbs.
Removes moisture and dirt from airlines; a float valve automatically ejectswater and dirt
Includes automatic oiler; protects toolsfrom freezing in cold environments
Eliminates air motor downtime causedby water and dirt
Connections for two tools, max. airflow 185 CFM
AirPac Dryer/CleanerModel CSAP-2
Model CSP-95
Hydraulic Power Unit
2 1317 0030*
2 1327 0010 SA
2 1327 0010 SV
Model No.
1-1/4"x7 UNC Male5/8"x11 UNC Male
G 1/2" Female
1-1/4"x7 UNC MaleG 1/2" Female
Optional: 5/8"x11
1-1/4"x7 UNC MaleG 1/2" Female
Optional: 5/8"x11
6 GPM
6 GPM
6 GPM
6"
12"
12"
3.6
4.2
4.2
MotorPower (HP)
Max.Drilling
Dia.
FreeSpeed (RPM)
ConnectingThreads
Oil Flow/2000 PSI
16
69
82
Weight(lbs.) Stand
N/A*
Anchor Stand
Anchor Standand Vacuum
Pump
Note: Hand-held core drills are intended up to a max. of 3" dia. for hand-held drilling or up to 6" dia. with a stand.* For Drill Rig with Anchor Stand, Order No. 2 1317 0030 SA; for Drill Rig with Anchor Stand and Vacuum Pump, Order No. 2 1317 0030 SV
380/900/1800
380/900/1800
380/900/1800
Load Speed (RPM)
Rugged 3-speed gearbox with mechanical slip clutch
Ideal for heavy-duty wet drilling in concrete, reinforced concrete and asphalt
Pneumatic power for hazardous areas and Ex zones
Air Tool LubricantProLube-ATL - P/N CS 7043-001 (gallon)
Air Tool Lubricant with Anti-FreezeProLube-ATL/AF - P/N CS 7049-001 (gallon)
Air Tool Line Conditioner/CleanerFor use in underwater air tools displacesmoisture and inhibits rust and corrosion ofair motors - P/N MS 9105 (quart)
19 1-800-700-5919 Visit our Web site at www.csunitec.com
Rotary Hammer Drills
2 1266 0010*
2 2404 0010
2 2404 0030*
2 2417 0010*
1" dia.
3" dia.
3" dia.
6" dia.
0-950
0-625
0-625
0-250
0-2000
0-3000
0-3000
0-2500
Blows/Minute(BPM)
DrillSpeed(RPM)
Core BitCapacity
(Concrete)
3/8" dia.3/4" dia.3/4" dia.
11/4" dia.
TwistDrill
(Wood)
0.75
0.7
0.7
1.6
21
21
21
53
MotorPower(HP)
CFM @90 PSI
7
11
11
26
Weight
1/2" Chuck
SDS Plus
SDS Plus
SDS Max
ToolSystem
12x 81/2 x 4
16x 81/2 x 4
16x 81/2 x 4
191/2 x9.8x41/2
Dimensions(inches)
* Underwater model Optional underwater air tool line conditioner to displace moisture, Part No. MS 9105.
1/2" dia.
1" dia.
1" dia.
2" dia.
Solid BitCapacity
(Concrete)
Air Model 2 2404 0010SDS Plus up to 1" dia.
Large Masonry BitsSDS Max up to 2" dia.
Small Masonry BitsSDS Plus up to 1" dia.
Hydraulic Model2 2406 0010 SDS Plus
SDS Drill BitsClosed-Center Flow Control Valve
SDS Plus Hammer and Drill1" bit capacity for drilling concrete and masonry
SDS Max Modes of Operation2" bit capacity for drilling concrete and masonry
HydraulicModel
2 2418 0010SDS Max
Hammer with RotationIdeal for concrete drilling
Rotation OnlyFor drilling steeland wood (not reversible)
Drill concrete anchor holes, thru holes,piping and mechanical openings for
construction and repair work. Switches torotary drilling mode for steel and wood.
Air Model 2 2417 0010
SDS Max
Second handleposition
SAE #8 port forhydraulic hoseconnection
SAE #8oil port
ATEXATEX
Optional accessory for use with closed-centerhydraulic power systems - adapts open-center toolsto closed-center. [Part No. 38632]
SDS chuck Safety clutch protects against overloading and jamming Hammer drill holes in concrete, brick and masonry Rotary drilling mode for straight drilling of steel and wood Open center hydraulic standard, closed center optional
Pneumatic and hydraulic:powerful percussiondrilling for concrete and masonry
PneumaticHammer Drill
Model No.
2 2406 0010
2 2418 0010
3" dia.
6" dia.
0-625
0-250
0-3400
0-2500
Blows/Minute(BPM)
DrillSpeed(RPM)
Core BitCapacity
(Concrete)
3/4" dia.
11/4" dia.
TwistDrill
(Wood)
0.8 HP
1.8 HP
5.8-13.2
2.6-13.2
Power@ 2000
PSI
FlowRange @1450 PSI
(GPM)
15
37
Weight
SDS Plus
SDS Max
ToolSystem
18x 101/4 x 4
191/2 x111/8 x71/2
Dimensions(inches)
Hydraulic Hammer Drills operate at hydraulic pressures of 1,450 - 2,000 PSI. Available with optional closed center.
1" dia.
2" dia.
Solid BitCapacity
(Concrete)
HydraulicHammer Drill
Model No.
20 1-800-700-5919 Visit our Web site at www.csunitec.com
Mixing Machines
Professional, Heavy-duty, Hand-held Mixers for Fast, Efficient Mixing
Mixing Station for Medium- to High-viscosity Batches
Model No.
0-450
250-580
0-450
100-275
9
11.5
15
15
9.5
10.5
10.5
14.5
EHR 18 S
EHR 20 R
EZR 22 R/RLTwin Paddle
EHR 23/1.3R
MotorPower (Amps)
LoadSpeed (RPM)
2 bags/20 gal.
3 bags/25 gal.
5 bags/25 gal.
5 bags/35 gal.
CapacityWeight(lbs.)
SuitablePaddles
WG 120MG 120RG 120
WG 135MG 140
TWP 140
P/N31610000(included)
WG 160MG 160
TWP 160
700lbs./hr.
900lbs./hr.
1200lbs./hr.
1800lbs./hr.
Max.Output
From self-leveling compounds to prefab mortar, CS Unitec has aportable mixer to do the job quickly. Every CS Unitec mixer hasbeen designed for high reliability, with the power to provideoptimum blending of construction materials on the job site.
24" paddlelength
14mmthreadconnection
1/2" hexshankavailable forstandarddrill chucks
Heavy-duty Galvanized Steel Mixing PaddlesHelical design mixes from the bottom up, eliminating air pockets
Portable Mixing Stands - Save time by running mixers independently
RG 1204.5" dia.
WG 1204.5" dia.
WG 1355.4" dia.
WG 1606.25" dia.
Low Viscosity Medium Viscosity
MG 1204.5" dia.
MG 1405.6" dia.
MG 1606.25" dia.
MG 2359.25" dia.
High Viscosity Fold & Stir
MH 240 9.625" x 6.25"Ideal for decorativeconcrete coatings
Model 25GP-WD Model RST 91 Model RST 10
CSUnitec offersthree air-poweredmodels that areinherently saferfor mixing paint,glue, epoxy, mortar,concrete, refractory cementand other materials in shipyards andthe oil and gas industries. They can beused around water with no fear ofshock or blown circuitry. Contact us for details.
Pneumatic-poweredMixers for HazardousEnvironments
EZR 22 R/RLPush-pull Mixer:Quick,
thorough mixing with twinpaddles and clockwise/
counterclockwise rotation
EHR 18 SIncludesWG 120paddle
EHR 20 R EHR23/1.3R
Ideal for mixing medium- to high-viscositymaterials, including filler and levelingcompounds, tile cement, ready-mixedmortar, plaster, screed and more.Reliable, high-power motor mixesbatches up to 30 gallons in heavy-dutybucket. Integrated safety switch disablesmotor if frame is lifted during mixing.
Automix 90Capacity: 3 bags, 30 gal.
Output: up to 900 lbs./hour
Power: 14 Amp / 110 Volt AC
Free Speed: 115 RPM
Load Speed: 50 RPM
Weight: 77 lbs.
Stirring Rod: No. 31460000 (included)
TWP 1405.5" dia.
TWP 1606.375" dia.
Overlayments &Colored Products
21 1-800-700-5919 Visit our Web site at www.csunitec.com
Portable Mixing Station
Mix, Transport and Pour Directly Onto the Floor!
PMH 70X-RL for Rough TerrainRimless Bucket and Removable Liner
Electric 110 Volt AC
16 Amp/1800 Watt2-speed Motor
1st Gear: 140 RPM(Load Speed)
2nd Gear: 470 RPM(Load Speed)
Model No. Motor Specifications
PMH 70F for Level FloorsWith Rimmed Bucket
PMH 70X for Rough TerrainWith Rimmed Bucket
PMH 70F-RL for Level FloorsRimless Bucket and Removable Liner
Multiple Batch Mixing with Removable LinerMixing multiple batches is easier and faster withthe new removable liner and rimless bucket system.
Mix consecutive batches without downtime Resilient, pliable liner is easily cleaned Alternating liners prevents cross contamination Extends life of bucket
After mixing the first batch, the liner canbe removed and cleaned. To speed upproduction, a second liner can be usedwhile the first liner is being cleaned. Theuse of a liner also helps to prevent crosscontamination and minimizes wear tothe HIPPO bucket, extending its life.
The HIPPO is also available with a Pneumatic-powered Mixing Motor2.2 HP, 90 PSI/67 CFM, 2 speeds (190/420 RPM)PMH 70F-AIR-RL; PMH 70X-AIR-RL; PMH 70F-AIR; PMH 70X-AIR
Bowl Capacity:5 x 40 lbs. mix+water (20 gal ./290 lbs.)5 x 20 kg mix+water (80 liters/130 kg)
Motor Mounting:Reversible for "alongside" mixing
Tilting Cradle:Balanced for easy operation
Weight: 99 lbs.
The PORTAMIX HIPPO features:
Easy operation one person can mix, transport and pour 5 bags or 20 gallons
Accurately place material directly onto the floor Produces excellent mix consistency Ideal for mixing and dispensing into 5-gallon containers Pre-tinted material is easily blended
22 1-800-700-5919 Visit our Web site at www.csunitec.com
Power
Blade Diameter
Max. Depth of Cut
Load Speed
No-load Speed
Weight
Blade
20 AMP / 110 V
7"
21/3"
4,300 RPM
7,500 RPM
17 lbs.
P/N 37444
Power
Blade Diameter
Load Speed
No-load Speed
Arbor Size
Max. Slot Width
Max. Cutting Depth
Weight
Blade, Standard, 6"
Blade, Premium, 6"
20 AMP / 110 V
6"
4,300 RPM
7,500 RPM
7/8"
113/16" (46mm)
13/4" (45mm)
12.8 lbs.
P/N 37440
P/N 37441
Model EMF 150
Wet / Dry 7" Electric Circular Saw
Walk-behind Cut-off Saw 20" Capacity
CSH 100
CSH 125
CSH 150
5 HP
9.5 HP
9.5 HP
Power
5250
3200
3200
RPM(No Load)
Max.Depthof Cut
4"
5"
7"
90
92
92
Direct
Gearbox
Gearbox
CFM @100 PSI
14
14
18
Max.Blade
Capacity
22
26
28
DriveWeight(lbs.)Model No.
Pneumatic Concrete Saws Hand-held and Walk-behindCut concrete, asphalt, masonry and more
Wet or dry cutting of concrete, reinforced concrete,asphalt, masonry, steel and more
Cut up to 7"deep with no gas or engine fumes
Low maintenance no belts,pistons, fuel lines or carburetors
Adjustable blade guard with built-in water connection
In-line oiler for motor lubrication
1" arbor size for diamond blades
1/2"NPT air connection
Cut up to 7"deep with no gas or engine fumes
Low maintenance nobelts, pistons, fuel lines orcarburetors
Designed for tough cuttingjobs, including jointsawing, floor sawing,trenching, road repair andplant maintenance
9.5 HPpneumatic motorwith gearbox drive
Wet and dry cutting of stone and masonry materials,including granite, marble, terrazzo and concrete
Adjustable cutting depth up to 2-1/3" for precise cuts
Ideal for landscapers, renovators and stone shops
Vacuum connection for use with CS Unitec's dustextraction vacuum systems
Cut channels in concrete andmasonry, adjustable sizes
Cut two parallel grooves up to113/16" wide x 13/4" deep
Operates with two parallel blades and spacers
Works 5/8" from the edge or corner
Wall Slotter
CSR 150 9.5 HP 2900 7" 92 Gearbox20 107
Hand-held Cut-Off Saw
CSR 150
Model EDS 181
Hand-held Cut-off Saws, 14" and 18"
Concrete Saws
Walk-behind Cut-Off Saw
Premium Diamond BladesWet/Dry, for Cured Concrete
Part No. Description734 906 12" x .125 x 1"734 908 14" x .125 x 1"734 916 16" x .125 x 1"734 909 18" x .125 x 1"734 910 20" x .125 x 1"RES.403 14" x .125 x 1" (rescue)
23 1-800-700-5919 Visit our Web site at www.csunitec.com
Diamond Concrete Chain Saws, Pneumatic and Hydraulic
CS 536163-1
CS 536163-2
CS 536163-3
CS 526822-1
CS 526822-2
CS 526822-3
6.5
6.5
6.5
11
11
11
Power(HP)
124 CFM @ 90 PSI (6 bar)
124 CFM @ 90 PSI (6 bar)
124 CFM @ 90 PSI (6 bar)
8 GPM @ 2500 PSI (172 bar)
8 GPM @ 2500 PSI (172 bar)
8 GPM @ 2500 PSI (172 bar)
32
33
34
28
29
30
104
104
104
95
95
95
88 dB
88 dB
88 dB
88 dB
88 dB
88 dB
Motor Specifications
5700
5700
5700
5700
5700
5700
No LoadSpeed(RPM)
Weight w/Bar andChain
No LoadTorque(in.-lbs.)
NoiseLevelat 3 ft.
10"
15"
20"
10"
15"
20"
Max.Depthof CutModel No.
Pneumatic Concrete Chain Saw
Hydraulic Concrete Chain Saw
CS 536163-PG2*
CS 536163-PG3**
6.5
6.5
Power(HP)
124 CFM
124 CFM
32 lbs.
33 lbs.
104
104
88 dB
88 dB
CFM@90 PSI
5700
5700
No LoadSpeed(RPM)
Weight w/Bar andChain
No LoadTorque(in.-lbs.)
NoiseLevelat 3 ft.
15"
20"
Max.Depthof CutModel No.
PowerGrit Diamond Air Saw for Ductile IronThe PowerGrit system allows the user to perform the entire cut from oneposition a feature especially helpful in reducing the amount of excavationrequired in underground cuts.
6
5
2.5
4.6
Specifically designed for the demanding requirements ofprofessional sawing and drilling contractors
Deep plunge cuts up to 20" deep
Square corners up to 19" with no overcuts
Cut mechanical openings andirregular shapes
* For 15" PowerGrit Saw and Pipe Clamp order no. CS 536163-PG2C** For 20" PowerGrit Saw and Pipe Clamp order no. CS 536163-PG3C
Concrete Saws
Air Powered
Air
Old
New
15" PowerGrit Chain P/N PG 52-3810
20" PowerGrit Chain P/N PG 53-5080
PowerGrit Pipe Clamp P/N PG 56-9960(12" cap.; includes mounting axle)
Optimized for air and hydraulic chainsawing -cut concrete with steel reinforcement
AirFORCE F4Diamond Chains
AirFORCE Premium Chains
10" Part No. CC 01-254015" Part No. CC 01-381020" Part No. CC 05-5080
Guide Bars with Internal Water Feed10" Guide Bar, for 25 segment Diamond Chain - P/N GB 01-254015" Guide Bar, for 29 segment Diamond Chain - P/N GB 03-381020" Guide Bar, for 34 segment Diamond Chain - P/N GB 05-5080
PowerGrit Chains and Clamp
Low-speed Polishers, Wet and Dry
For stone, concrete, metal, plastic, glass and moreCSUnitec offers severalpolishing tools for both wet anddry applications. These toolsfeature either double or triplegear reduction for maximumtorque with minimum motorload and a longer service life.
Model No.
650-1150
1300-3050
1300/2175/3075
9"
5"
5"
12
12
12
ELP 1300
EPO 1310
EPN 1310 P
MotorPower*
110 V-60 HzMax.Dia.
Load Speed(RPM)
6.4
5
6.4
Weight(lbs.)
* All models are available with a 230 V/50Hz motor.
EPN 1310 P - WetEPO 1310 - Dry
ELP 1300 - Automotive Polisher
CS UNITEC, Inc.22 Harbor Avenue, Norwalk, CT 06850Phone 800-700-5919 203-853-9522 Fax 203-853-9921Email [email protected] www.csunitec.com
ALL SPECIFICATIONS ARE SUBJECT TO CHANGE Copyright 2013, CS Unitec, Inc., 10-13-10M
Stone Polishers
View product demonstrationsat www.csunitec.com.
Planetary Sander/Polisher
Sands, grinds, hones and polishesBuilt-in dust extraction Triple-sealed bearings High torque
The DS3011 planetary polisher produces a flat, swirl-free finish oncountertops, floors, walls and steps. The unit will grind, hone, polish andclean concrete, terrazzo, marble, granite and corian surfaces usingcoated abrasives, diamond polishing systems and lightweight diamond
wheels. The system operates wet by default, ordry with the integrated dust cowl.
This is a true planetary-driven tool.The 12"platform turns ata lower rate than the higher rotational speed of the 5"platens. This combination of RPM provides the optimalspeed for polishing, producing a perfect finish 5x faster thana single-head polisher. A center coolant feed, precisionbearings and sturdy construction make this the ultimate toolfor perfect finishes and superior polish.
Power
12" Platform Speed
5"Platen Speed
3 Platens
Weight
11 AMP / 115 V, 60 Hz
405 RPM
2100 RPM
5" (with 5/8" - 11 thread)
30 lbs. (47 lbs. with platens)
Model DS 3011
DS 3011 C Kit DS 3011 with set of AbrasiveDiamond Pads 3 each, 50 grit to 1500 grit.
IN-C5R050 50 Grit Wet/Dry Resin pad
IN-C5R010 100 grit Wet/Dry Resin Pad
IN-C5R020 200 grit Wet/Dry Resin Pad
IN-C5R040 400 grit Wet/Dry Resin Pad
IN-C5R080 800 grit Wet/Dry Resin Pad
IN-C5R150 1500 grit Wet/Dry Resin Pad
DS3011 Accessories