HiPath 3000 5000 V7.0 Getting Started Guide Issue 4

8/3/2019 HiPath 3000 5000 V7.0 Getting Started Guide Issue 4

1/38

www.siemens.com/enterprise

Getting Started

HiPath 3000/5000 V7IP-Systeme

Getting Started

P31003-H3570-G100-4-7631


2/38

www.siemens.com/enterprise

Copyright Siemens Enterprise Communications GmbH & Co. KG 2007

Hofmannstr. 51, D-81359 Mnchen

Reference No.: P31003-H3570-G100-4-7631

The information provided in this document contains merely general

descriptions or characteristics of performance which in case of actual use do

not always apply as described or which may change as a result of further

development of the products. An obligation to provide the respective

characteristics shall only exist if expressly agreed in the terms of contract.

Subject to availability. Right of modification reserved. The trademarks used

are owned by Siemens Enterprise Communications GmbH & Co. KG or their

respective owners.


3/38

GetstartedTOC.fm

P31003-H3570-G100-4-7631 , 2007-10-31

HiPath 3000/5000 V7, Getting Started 0-1

Nur fr den internen Gebrauch Contents

Contents 0

1 Whats New? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

1.1 Version 7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-11.2 Version 6.0 SMR9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5

2 Basics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-12.1 Target Group and Use of this Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-12.2 Varieties of the HiPath 3000/5000 IP System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1

2.2.1 HiPath 3000 V7 IP System (Standalone) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-22.2.2 HiPath 3000 V7 Networked IP Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-32.2.3 HiPath 5000 V7 IP System (Networked System) . . . . . . . . . . . . . . . . . . . . . . . . . 2-4

2.3 Typographical Conventions and Symbols Used . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-52.4 Further Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6

3 Preparations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1

4 HiPath 3000/5000 V7 IP Systems. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-14.1 Step by Step Startup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1

4.1.1 Installing the Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-14.1.2 Installing Additional HiPath 3000 Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-24.1.3 Initial Startup of HiPath 3000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-24.1.4 HiPath 5000 (Networked System) Variety - Installing HiPath 5000 Server . . . . . . 4-34.1.5 Connecting the HiPath 3000 to the LAN via the HG 1500 . . . . . . . . . . . . . . . . . . 4-44.1.6 Initial Configuration of the HiPath 3000. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-74.1.7 HiPath 5000 (Networked System) Variety - Merging HiPath 3000 (Nodes) . . . . . 4-9

4.1.8 Licensing the Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-104.1.9 Configuring the IP Clients . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-134.1.10 Further Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-164.1.11 Connection to the Internet. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-16

Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Z-1


4/38

Contents Nur fr den internen Gebrauch

P31003-H3570-G100-4-7631 , 2007-10-310-2 HiPath 3000/5000 V7, Getting Started

GetstartedTOC.fm


5/38

neues.fm

P31003-H3570-G100-4-7631 , 2007-10-31


Nur fr den internen Gebrauch Whats New?

Version 7

1 Whats New?

1.1 Version 7

The following table describes the new features in Version 7. It provides information on the me-aning these features have for the user, and which internal technical modifications have takenplace.

Feature User benefits Technical changes

OpenStage TDM OpenStage is a new product line forbusiness communications. Its at-tractive design, with the versatileclick wheel and user-friendly LC

display, combines convenience andeffectiveness.Models include the OpenStage 20TDM and OpenStage 40 TDM.

ISDN numberingplan (E.164)

New numbering plan for addressingtelephone networks which specifiesthe components of a phone numberand how many digits it may contain.

Better integration into networks withHiPath 4000, into applications andlater with Internet telephony serviceproviders.The numbering plan can be config-ured using Manager E.

Number of keymodulesincreased to 250

Key modules are add-on devicesthat may be attached to the side ofyour telephone. They increase thenumber of programmable keys pertelephone.

Previously limited to 100, now 250key modules may be connected toHiPath 3800 systems.

Route optimizati-on in networkedHiPath 3000/5000systems

Route optimization is provided for IPnetworking on HiPath 3000/5000 sy-stems, i.e. transit traffic with identicalsource and target systems (switchedor forwarded traffic). No more chan-

nels are blocked.Call forwarding tovoice mailbox

When forwarding calls from stationA to station B, the system may beconfigured to record unansweredcalls from voice mailbox A or B.

This feature can be activated withManager E (Station view | Flags |Last destination mailbox active).


6/38

Whats New? Nur fr den internen Gebrauch

P31003-H3570-G100-4-7631 , 2007-10-31

1-2 HiPath 3000/5000 V7, Getting Started

neues.fm

Version 7

LDAP diagnosis If there is no response or a bad re-sponse to a query to an LDAP ser-

ver, the display of the querying de-vice (Optiset E, optiPoint,OpenStage TDM) shows one of thefollowing error messages: "Server cannot be reached" "Server busy" "Server error"When a search query has led to noresult, the "No result" error messa-ge appears.

HG 1500 provides an error report viaEvent log/Customer trace and

SNMP trap (configurable).

Remote upgradeconcept The HiPath system software can beupgraded remotely. Customer datais modified to comply with the newsoftware.This function, in particular for HiPath5000 upgrades, is described in theservice manual.

analog trunk CLIP When a call arrives over an analogtrunk, the callers number is shownon the display of the analog extensi-on phone (also applies for optiPointphones).

The TMANI and TLANI modules col-lect the necessary data and forwardit.



7/38

neues.fm

P31003-H3570-G100-4-7631 , 2007-10-31



Version 7

EFC (ExtendedFast Connect)

In HiPath 3000/5000 V7, the CorNet-IP protocol has been extended with

the addition of the EFC (ExtendedFast Connect) protocol variant. EFCis needed for possible future features(such as encryption of signaling andvoice data in LANs and "IP/IP e2epayload via enterprise proxy for In-ternet telephony). All of a systemsIP workpoints (HFA) and all IP work-points (HFA) within a network mustsupport the EFC protocol. The IPworkpoints optiPoint 420 and optiCli-ent 130 may need to be upgraded toEFC-capable software. optiPoint400, optiPoint 600 office (CorNet-IPmode) and optiPocket are not EFC-capable and therefore will no longerbe supported as of HiPath 3000/5000 V7.

Direct Payload tothe Internet tele-phony service pro-

vider

Direct payload builds on EFC. Callsare routed directly to the Internet te-lephony service provider via custom-

er LAN and the router. Therefore noB channels on the HG 1500 moduleare used from an IP telephone toInternet telephony service provider.Previously, every IP telephone occu-pied two B channels on the HG1500. This limitation no longer ex-ists. Each TDM telephone still occu-pies a B channel.

T.38 via SIP Fax communication via SIP The protocol T.38 enables secure fax

signals to be sent to the Internet te-lephony service provider. This func-tion can enabled using WBM; it is ac-tivated in the default setting.



8/38


P31003-H3570-G100-4-7631 , 2007-10-31


neues.fm

Version 7

CSTA monitoringof Internet tele-

phony service pro-vider lines

Enables the integration of Internettelephony service provider lines into

application connected to the HiPathsystem via the CSTA interface.Therefore there are no longer anyCSTA differences between TDM andInternet telephony service providerlines.

Mobility Entry (notfor USA)

This feature allows mobile stationsto be integrated into theHiPath 3000 system. Mobile stati-ons are GSM telephones and tele-

commuter workplaces. The stationhas access to system features.

This feature is implemented throughDISA. A mobile station is assigned toa virtual station in the system. In theHiPath 3000 system, all features are

thus mapped to the virtual stations.

Lightning protec-tion strip(part numberC39334-Z7052-C31)

Additional lightning protection forHiPath 3000 (for Brazil only)

Lightning protection up to about4 kV.The power supply cable of theHiPath 3000 must be plugged intothe lightning protection strip. Thelightning protection strip should beconnected to the line voltage.

>As of HiPath 3000/HiPath 5000 V7, the node station number is entered as follows::Settings | System parameters | Flags. The path "Settings | Lines/networking | Rou-tes | PABX Number Incoming: PABX number" is no longer possible.When updating to V7, note that after the customer database conversion, the nodenumber is entered under Settings | System Parameters | Flags. Otherwise IP net-worked subsystems can no longer call the CO.



9/38

neues.fm

P31003-H3570-G100-4-7631 , 2007-10-31



Version 6.0 SMR9

1.2 Version 6.0 SMR9


SIP DID (= Direct In-ward Dialing)

The user receives a DID con-nection for Internet telephony.

The Internet telephony service provi-der provides a PABX number with anextension number range.

Internet telephonyservice provider in IPnetworking

A HiPath system can be registered atan Internet telephony service providerand integrated in an IP network at thesame time. The systems in the networkcan also use the SIP numbers for in-coming and outgoing calls.Each extension (TDM, HFA, SIP and

H.323 devices) in the networked sys-tem may obtain an MSN/DDI from theInternet telephony service provider ortransmit its default station numberwhen called.

Four Internet telepho-ny service providerssimultaneously

Using several providers helpsto reduce costs.

Up to four ITSPs (Internet TelefonieService Provider) can be connected toa HiPath system at the same time.ITSPs can be prioritized using LCR onthe basis of the number dialed and the

time.STUN support HiPath provides a STUN client for NAT

Traversal that works together with aSTUN server at the ITSP. The ITSP isaccessed by an external router con-nected to the HiPath.

Lightning protectionstrip(part numberC39334-Z7052-C31)

Additional lightning protectionfor HiPath 3000 (for Brazil on-ly)

Lightning protection up to about 4 kV.The power supply cable of the HiPath3000 must be plugged into the light-ning protection strip. The lightning pro-

tection strip should be connected tothe line voltage.


10/38


P31003-H3570-G100-4-7631 , 2007-10-31


neues.fm

Version 6.0 SMR9


11/38

intro.fm

P31003-H3570-G100-4-7631 , 2007-10-31


Nur fr den internen Gebrauch Basics

Target Group and Use of this Manual

2 Basics

2.1 Target Group and Use of this Manual

This document contains brief installation and startup instructions for a HiPath system or network.It is intended for technically advanced customers who want to perform the initial startup of theirHiPath 3000/5000 IP system themselves, and configure the basic Internet telephony features.In addition, it is a useful aid for trained service personnel who want a brief overview of the chro-nological sequence of startup activities.

2.2 Varieties of the HiPath 3000/5000 IP System

HiPath 3000/5000 V7 is a highly scalable communications system designed for both small and

medium-sized companies as well as for extensive enterprise networks. HiPath 3000/5000 V7is available in a wide range of configurations from straightforward standalone systems with asmall number of stations to centrally administered networks with 64 nodes and up to 2000workpoint clients (IP and TDM telephones and IP clients). The system architecture avails of theadvantages of distributed systems to spread the load placed on individual components and toachieve optimal performance.

HiPath 3000/5000 V7 is available in the following three varieties:

HiPath 3000 V7 IP System (Standalone)

HiPath 3000 V7 Networked IP Systems

HiPath 5000 V7 IP System (Networked System)

>A general introduction to the HiPath 3000/5000 family of products can be found in the System Description and in the Service Manualfor HiPath 3000/5000 V7. These documents also contain detailed information on sy-stem installation and startup.


12/38

Basics Nur fr den internen Gebrauch

P31003-H3570-G100-4-7631 , 2007-10-31


intro.fm

Varieties of the HiPath 3000/5000 IP System

2.2.1 HiPath 3000 V7 IP System (Standalone)

This variety is based on Euro-ISDN technology and enables a mix of analog and digital work-point clients (such as OpenStage TDM) and IP-based workpoint clients (such as optiPoint 420,

optiPoint 420 S, optiClient 130).

LAN/IP

IP phones, e.g.optiPoint 420,optiPoint 420 S

optiClient 130 V5

HiPath 3000 V7

including HG 1500

HiPath Cordless integrated

HiPathadministration PCincl. applications, e.g.HiPath Xpressions,HiPath ProCenter,SimplyPhone,... UP0/E phones such as

optiPoint 500, OpenStageTDM

PSTN/ISDN

Fax,analog telephones

HiPath Wireless:

optiPoint WL2professional


13/38

intro.fm

P31003-H3570-G100-4-7631 , 2007-10-31




2.2.2 HiPath 3000 V7 Networked IP Systems

This variety is a composite of several IP-networked HiPath 3000 V7 (nodes) and enables a mixof analog and digital workpoint clients (such as optiPoint 500) and IP-based workpoint clients

(such as optiPoint 420 and optiClient 130 V5). It also makes it possible to network several no-des over IP.

LAN/IP


optiClient 130 V5

HiPath 3000 V7

including HG 1500


HiPathadministration PCincl. applications, e.g.HiPath Xpressions,HiPath ProCenter,SimplyPhone,...

PSTN/ISDN


PSTN/ISDN

HiPath 3000 V7including HG 1500

UP0/E phones such asoptiPoint 500, OpenStageTDM

UP0/E phones such asoptiPoint 500, OpenS-tage TDM

HiPath Wireless:



14/38


P31003-H3570-G100-4-7631 , 2007-10-31


intro.fm


2.2.3 HiPath 5000 V7 IP System (Networked System)

This variety is a purely IP-based communication system that is installed on Windows 2003 ser-ver PCs and equipped with open architecture. This allows HiPath 5000 PCS V7 to be imple-

mented in various multi-node systems (e.g. together with HiPath 3000 V7 and/or HiPath 4000V3.0), making possible a wide range of implementation scenarios and customized configurati-ons. System administration is performed with the HiPath 5000 RSM. Central administration caneither run on the HiPath 5000 PCS server or on additional application servers (depending onthe application scenarios and the system configuration).

LAN/IP

HiPath 5000 V7 server,HiPath 5000 administration PCincl.Feature Server,

HiPath ComScendo Service,HiPath 3000 Manager


optiClient 130 V5

e.g. HiPath 3000 V7including HG 1500


HiPath application ser-ver, for example with HiPathXpressions, HiPath Pro-Center,HiPath SimplyPhone, etc.

PSTN/ISDN


PSTN/ISDN

e.g. HiPath 3000 V7including HG 1500

UP0/E phones such asoptiPoint 500, OpenStageTDM

UP0/E phones such asoptiPoint 500,OpenStage TDM

HiPath Wireless:



15/38

intro.fm

P31003-H3570-G100-4-7631 , 2007-10-31



Typographical Conventions and Symbols Used

2.3 Typographical Conventions and Symbols Used

... the OK button ... Buttons and menus are shown in bold type. Body text that is

especially important or should be read carefully is also for-matted in bold.

... file global.cfg ... Files or directories appear in Courier font.

Entries or information, which can vary depending on the situationat hand, appear in angle brackets.

>This symbol indicates notes or recommendations.

7This symbol indicates warnings that must be observed.


16/38


P31003-H3570-G100-4-7631 , 2007-10-31


intro.fm

Further Information

2.4 Further Information

Further information on HiPath 3000/5000 V7 is provided in the following documents:

System DescriptionThe System Description provides a comprehensive overview of the systems and boardscontained in HiPath 3000/5000 V7. Providing more detail than sales release documentati-on, this document describes new feature highlights and those already provided by previousversions. Supported workpoint clients and applications are also listed.

Feature Description

The Feature Description lists and describes in detail all HiPath 3000 and HiPath 5000 fea-tures, grouped according to topic. Dependencies with other features and possible restric-tions are also described.

Service Manual

The service manual provides information on systems corresponding to HiPath 3000/5000.The information provided includes descriptions of all HiPath 3000-compatible boards, in-formation on standard installation and startup procedures for the various HiPath 3000 sy-stems, startup and administration of HiPath 5000 RSM and the HiPath ComScendo Ser-vice, information on HiPath License Management and details of the workpoint clientssupported.

Manager E Administrator Documentation

With HiPath 3000 Manager, you can administrate and configure HiPath 3000 andHiPath 5000 communication systems. You can manage either a standalone communicati-on system or a network comprising several HiPath 3000 and HiPath 5000 communicationsystems by configuring the corresponding customer data memory (CDM). With netwideadministration you can access and modify the central customer data memory from a cen-tral location in the network (e.g. configure, modify or relocate stations).

HG 1500 Administrator Documentation

These instructions provide a complete description of the administration options offered byHG 1500. They explain clearly and concisely how to administer and configure a gatewayvia the Web-Based Management (WBM) interface.


17/38

intro.fm

P31003-H3570-G100-4-7631 , 2007-10-31



Further Information

Inventory Manager User Guide

With the Inventory Manager, you can quickly obtain a complete overview of all integratedcomponents and installed applications in the HiPath 3000/5000 V7 network. For service

technicians, the quick, concise overview which can be called up for the version numbers ofall communication servers in the network (HiPath 3000 and HiPath 5000) can be particu-larly useful. The information can be accessed from every PC in the network.

The following information can be called up:

Information on all HiPath 3000 and HiPath 5000 systems in the network, including in-formation on their respective boards (e.g. HG 1500),

Information on all applications and operating systems installed on the PCs in the net-work,

Display of the hierarchical structure of hardware components and their software versi-ons.

Software Manager User Guide

With the Software Manager you can query, update and back up the current system soft-ware for individual HiPath components via a web browser. The assignment of the HiPathcomponents to the individual nodes can also be quickly ascertained. The functions are dis-tributed as follows:

with the integrated Upgrade Manager you can query and update the system software

of all HiPath components, with the integrated Backup Manager you can back up the system software. These bak-

kups can then be used to restore the systems in the event of a system crash.


18/38


P31003-H3570-G100-4-7631 , 2007-10-31


intro.fm

Further Information


19/38

allg_Hinweise.fm

P31003-H3570-G100-4-7631 , 2007-10-31


Nur fr den internen Gebrauch Preparations

3 Preparations

The following points must be clarified and carried out before HiPath 3000 installation and initial

setup. Cross references to the associated documentation provide further details. If you havethese instructions in electronic form, click the blue links and you will be branched to the corre-sponding documentation.

Subject Description Detailed infor-mation

Safety notes Please pay attention to the relevant safety information on instal-ling, upgrading and initial setup.

HiPath 3000 Ser-vice Manual,Chapter SafetyNotes

Delivery docu-ments Compare items delivered with the units listed in the delivery docu-ments.

Completeness/integrity

Test unit integrity.Are there signs of transport damage?

Installation siteconditions

Does the installation site meet all necessary requirements interms of surroundings and power supply?

HiPath 3000 Ser-vice Manual,Chapter HiPath3000 Installation

Licensing Is all the licensing data for any networked HiPath 3000 systemsavailable, such as the authorization code and the MAC address(MAC-ID) for all HiPath 3000 Control Boards (CB)?Is all of the licensing data for a HiPath 3000/5000 network availa-ble, such as the authorization code and the MAC address (MACID) of the first HiPath 3000 Control Board (CB) with the lowestnode ID?Is there Internet access for licensing?Is there a license file available for each HiPath 3000 and is it in-stalled correctly in the CLA (Customer License Agent)? You onlyneed one license file for networked HiPath 3000 systems with Hi-Path 5000. The license files and access to the license server areprovided via License Management.Note:

The licensing period is 30 days. The relevant features must be li-censed within this time.

Requirementsspecification,licensing docu-ments

HiPath 3000 Ser-vice Manual, Li-censing Chapter

License serverURL:https://www.sie-mens.com/licen-se-management

requirementsspecification

Is the requirements specification agreed with the customer availa-ble and does it contain all the necessary data?Is further information required?

See require-ments specificati-on

Numbering plan Has a numbering plan been developed in line with customer re-quirements?

See also therequirements spe-cification
https://www.siemens.com/license-managementhttps://www.siemens.com/license-managementhttps://www.siemens.com/license-managementhttps://www.siemens.com/license-management


20/38

Preparations Nur fr den internen Gebrauch

P31003-H3570-G100-4-7631 , 2007-10-31


allg_Hinweise.fm

LAN require-

ments

Does the LAN meet the requirements for Voice over IP? Has a

network analysis been performed? Are the results available? Isthere a list of IP addresses that are already assigned/still availa-ble? Are the IP addresses of the IP clients already defined andhave they been assigned call numbers?

Refer to the requi-

rements specifi-cation

HiPath 3000 Ser-vice Manual,Chapter IP Fun-damentals

Administration It is configured using the service tool HiPath 3000 Manager C/ETo configure the HG 1500 module, you need Internet ExplorerV5.5 or later and Java. HiPath 3000 Manager should be availableon the technicians service laptop or should be installed on a sta-tionary PC (administration PC) at the customer site (in agreement

with the customer). Or, in a HiPath3000/5000 network, the Mana-ger can be installed on the HiPath 5000 RSM server (administra-tion PC) for central administration.You can install both of these programs from CD 1 via the mastersetup. Is there no CD? If you are a customer: Ask your contact at Siemens. If you are a Siemens technician: Load the programs from the

software server (SWS).The V.24 interface and then thae LAN are used to connect to thesystem.

Subject Description Detailed infor-mation


21/38

IP_Network.fm

P31003-H3570-G100-4-7631 , 2007-10-31


Nur fr den internen Gebrauch HiPath 3000/5000 V7 IP Systems

Step by Step Startup

4 HiPath 3000/5000 V7 IP Systems

4.1 Step by Step Startup

Perform the steps described below in chronological order to start up multiple HiPath 3000 sy-stems with HG 1500 modules or with the HiPath 5000 server. Each subject has a cross refe-rence to relevant documentation providing further details. If you have these instructions in elec-tronic form, click the blue links and you will be branched to the corresponding documentation.

4.1.1 Installing the Hardware

>Startup of a single HiPath 3000 system is described below. When starting additionalHiPath 3000 systems perform the steps described below again.

Activity/description Detailedinformation

1. Mounting/installing the HiPath 3000 system.

In case of the HiPath 5000 V7 IP system (networked system):Mounting/installing the HiPath 3000 systems (nodes).

HiPath 3000 Ser-vice Manual,Chapter HiPath3000 Installation

2. Mounting and installing the client PCs, administration PC and - if neces-sary - switches and routers.

In case of the HiPath 5000 V7 IP system (networked system):Mounting and installing the HiPath 5000 server (also the administrationPC), the client PCs, and - if necessary - switches and routers.

3. Mounting, installing, and cabling of workpoint clients on a system-spe-cific basis.

HiPath 3000 Ser-vice Manual,Chapter WorkpointClients

Status:The HiPath 3000 system/HiPath 3000 systems, the server (in the case

of the HiPath 5000 V7 IP system (networked system), and the work-point clients used are at their installation site and physically connectedto the LAN.


22/38

HiPath 3000/5000 V7 IP Systems Nur fr den internen Gebrauch

P31003-H3570-G100-4-7631 , 2007-10-31


IP_Network.fm


4.1.2 Installing Additional HiPath 3000 Modules

4.1.3 Initial Startup of HiPath 3000

Initial startup must be performed for each HiPath 3000 system.

Activity/description Detailed

information1. The system must be disconnected from the power source (in the case

of HiPath 35x0 and HiPath 33x0) before new modules are added.HiPath 3000 Ser-vice Manual,Chapter HiPath3000 Modules

2. Check the available ports (master/slave) for each slot (HDLC). HiPath 3000 Ser-vice Manual,Chapter Configu-ration Instructions

Status:New modules are installed correctly in the system.

7Caution (for Brazil only)

For protection against overvoltage due to lightning, the use of the lightning protectionstrip with part number C39334-Z7052-C31 is absolutely mandatory. In the HiPath3000 Service Manual, HiPath 3000 Startup Chapter, following the described voltage

supply steps.


1. Connect the V.24 interface of the HG 1500 module and the serial inter-face of the administration PC (e.g. COM1) using a null modem cable.Note:Initial connection of the system to the LAN using a direct connection(null modem cable) is described below.

HiPath 3000 Ser-vice Manual,Boards Chapter,select the corre-sponding board

(e.g. HXGM3,

HXGR3, HXGS3,etc.).

2. Connect the system to the power source and perform a reload.A default CDB (Customer DataBase) is loaded with the country settingGermany.Note:When using a lightning protection strip (part number C39334-Z7052-C31), carry out the voltage supply steps described in the Service Ma-nual.

HiPath 3000 Ser-vice Manual,Chapter HiPath3000 Startup


23/38

IP_Network.fm

P31003-H3570-G100-4-7631 , 2007-10-31




4.1.4 HiPath 5000 (Networked System) Variety - Installing HiPath 5000Server

HiPath 5000 V7 is installed on a server PC and includes the HiPath ComScendo Service soft-ware suite and the DB Feature Server. The server PC on which HiPath 5000 V7 is installed isgenerally also the administration PC of the network, which also includes HiPath 3000 Manager,Software Manager, Inventory Manager, etc. Other applications such as HiPath ProCenter Of-fice, for example, can also run on the administration PC. For performance reasons, however,the administration PC and application PC can be separate in the network.

3. Perform country initialization with Assistant T, if necessary. Germany

is set by default. If you have changed the country initialization, theHiPath 3000 is restarted.

HiPath 3000 Ser-

vice Manual,Chapter HiPath3000 Startup

Status:The HiPath 3000 is booted, the connected system telephones are de-tected and the ISDN lines are configured for the EDSS1 protocol.


1. Install all desired components using master setup.

Note:During installation, perform only basic configuration for the respectivecomponents when prompted. Once installation is complete, theuser, TAPI lines, IP clients and B channels should also be configured.

HiPath 3000 Ser-

vice Manual,Chapter HiPath5000 ComponentInstallation

2. Install HiPath 3000 Manager using master setup. HiPath 3000 Ser-vice Manual,Chapter HiPath5000 ComponentInstallation

Status:

The HiPath 5000 Server is installed.



24/38


P31003-H3570-G100-4-7631 , 2007-10-31


IP_Network.fm


4.1.5 Connecting the HiPath 3000 to the LAN via the HG 1500

The HiPath 3000 is connected to the LAN via the HG 1500. You must first assign an IP addressto the LAN1 interface of the HG 1500 and a default router to the gateway. When connecting

additional HiPath 3000 systems (nodes) you must repeat the steps described below.

For initial setup of the HG 1500, you have the following possibilities:

use the Command Line Interpreter (CLI)

carry out the initial setup via remote access

Initial setup using the CLI is described below.


Starting and configuring the HyperTerminal connection

1. Start HyperTerminal on the administration PC underStart | Programs | Accessories | Communications.

Make the following settings:

2. Specify a name for the connection, e.g. HG 1500.

3. Select the COM port to which the HG 1500 is connected, e.g. COM1.

4. Make these settings: for HG 1500 19200 bps for STMI 38400 bps

Administration using the Command Line Interface (CLI)

1. When the HyperTerminal connection has been established, you canaccess the HG 1500by pressing the Enter key.

HG 1500 Admin.,Chap. Configurati-on via CLI Inter-face

2. Log on with a username and password. The default username andpassword can be obtained from the system administrator.

Note:You can change the username and password using HiPath 3000Manager E in the HiPath 3000 system.

In the CLI, enter the following commands after the vxTarget> prompt:

3. get write accessActivates write function.


25/38

IP_Network.fm

P31003-H3570-G100-4-7631 , 2007-10-31




4. set ip address xxx.xxx.xxx.xxx

Wildcard for IP address of the HG 1500 LAN1 interface, e.g.1.150.1.232Note:Before assigning an IP address, use Ping to ensure that this addresshas not already been assigned.

5. set ip subnet yyy.yyy.yyy.yyyWildcard for subnet mask of the HG 1500 LAN1 interface, e.g.255.0.0.0

6. set default gateway zzz.zzz.zzz.zzzWildcard for the default router of the gateway, e.g. 1.150.6.10.

7. add wbm client aaa.aaa.aaa.aaaWildcard for PC that the HG 1500 can configure using Web-Based Ma-nagement, e.g. 1.150.1.10.

8. save configurationStores the settings.

9. resetRestarts the HG 1500.

Once the entries for IP addresses 1 and 2 are displayed on the CLI, thereset is complete. Press the Enter key again to return to the login

prompt.

Closing the HyperTerminal connection

1. Close the HyperTerminal program to release the COM interface forsubsequent administration with HiPath 3000 Manager.

Administration with HiPath 3000 Manager

1. Connect the V.24 interface of the HiPath 3000 and the serial interfaceof the administration PC using a null modem cable.

Note:You can remove the null modem cable from the HG 1500 and insert itin the HiPath 3000 V.24 interface. This can be done while the systemis running.

HiPath 3000 Ser-vice Manual,

Chapter HiPath3000 Modules



26/38


P31003-H3570-G100-4-7631 , 2007-10-31


IP_Network.fm


2. Start HiPath 3000 Manager with Start | Programs | HiPath 3000 Ma-

nager | HiPath 3000 Manager and log on with a username and pass-word. The default username and password can be obtained from thesystem administrator.Note:You can change the username and password using HiPath 3000Manager E in the HiPath 3000 system.

HiPath 3000 Ma-

nager, ChapterStartup And Login

3. Load the CDB from the HiPath 3000 by means of the direct connectionwith File | Transfer | Communication | System -> PC.The options Direct and Read/write CDB must be selected.

HiPath 3000 Ma-nager, ChapterTransfer | Commu-nication

4. In Settings | Network | Basic Settings, set the IP access protocol toHIP.HiPath 3000 Ma-nager, ChapterBasic Settings

5. In Settings | Network | Basic Settings, enter the IP address ofHiPath 3000 (e.g. 1.150.1.231) and the subnet mask of HiPath 3000(255.0.0.0) in the LAN Interface field.

HiPath 3000 Ma-nager, ChapterBasic Settings

6. If required, specify which IP PCs are to be accessed via which gatewayunder Settings | Network | Routing. Enter the IP address of the IP PC(e.g. 1.150.1.112), the subnet mask (e.g. 255.0.0.0) and the gateway(e.g. 1.150.1.10).

HiPath 3000 Ma-nager, ChapterRouting

7. Restore the data to the system via the direct connection with File |Transfer | Communication | PC -> System.


8. Save the CDB.File | Save CDB As...

HiPath 3000 Ma-nager, ChapterSave CDB As...

Status:The HiPath 3000 can now be configured via LAN with HiPath 3000 Ma-nager. The null modem cable can be removed from the HiPath 3000.



27/38

IP_Network.fm

P31003-H3570-G100-4-7631 , 2007-10-31




4.1.6 Initial Configuration of the HiPath 3000

Initial configuration must be performed for each individual HiPath 3000 system.


1. Connect the HG 1500 of the HiPath 3000 with the LAN.Note:The administration PC must also be connected to the LAN.

HiPath 3000 Ser-vice Manual,Boards Chapter,select the corre-sponding board

(e.g. HXGM3,

HXGR3, HXGS3,

etc.).

2. Check the LAN connection to the HG 1500 and to the HiPath 3000using a Ping command (e.g. ping 1.150.1.231).Now use HiPath 3000 Manager to load the CDB of HiPath 3000 withFile | Transfer | Communication | System -> PC.The options Read/write CDB and IP HiPath must be selected. As theIP address, select the IP address of the HiPath 3000 (in our example:1.150.1.231).


3. In case of the HiPath 5000 V7 IP system (networked system):Activate the HiPath 5000 functionality with Settings | Network | Hi-Path 5000 Parameters.

Specify the IP address of the HiPath 5000 Server PC and the node IDof the HiPath 3000 that you are currently managing. The node ID mustbe unique within the network.

HiPath 3000 Ma-nager, Chap. Hi-Path 5000 Para-meter

4. Check whether the system telephones were detected correctly by sel-ecting Settings | Set up Station | Stations.Assign the appropriate station names to the station numbers of the sy-stem telephones (can be found in the customers numbering plan or therequirements specification).Note:Here you can already assign the appropriate station names to the sta-tion numbers of the IP clients (can be found in the customers numbe-

ring plan or the requirements specification).

HiPath 3000 Ma-nager, Chapter Setup Station | Stati-ons

5. You can change the station parameters by clicking the Station Viewbutton above the navigation area.

HiPath 3000 Ma-nager, ChapterStation View

6. Enter a name for the system in the System Name field underSettings | System Parameters | System Settings. This name is dis-played on the display of the system telephones (currently not onOpenStage 40, 60, 80).

HiPath 3000 Ma-nager, Chapter Sy-stem Settings


28/38


P31003-H3570-G100-4-7631 , 2007-10-31


IP_Network.fm


7. Under Settings | Lines/Networking | Routes, specify a route name

(e.g. ISDN) in the Route Name field and the international dialing code(e.g. 49), the area code (e.g. 89), and the call number of the systemwithout intercept code (e.g. 722) in the System Number-Incomingfield.

HiPath 3000 Ma-

nager, Chap. Rou-tes.

8. Check the protocol of the trunks with Settings | Lines/Networking |Trunks. To do this, select a line and click the corresponding "Param"field.

HiPath 3000 Ma-nager, ChapterTrunks

9. Load any additional system languages with System Status | System-wide | System Texts. There are a total of eight system languages inall, four of which are defined by default and the other four loaded on a

user-defined basis.Note:When loading the system languages, you should first transfer the CDBto the system, save it, and then change the system languages. A re-start is performed automatically following a change to the system lan-guages.

HiPath 3000/5000Feature Usage Ex-amples, Swapping/

Replacing Langua-ges

10. Restore the data to the system withFile | Transfer | Communication | PC -> System




The date and time are updated after the first connection setup to theCO.

Status:The system telephones have been set up correctly, the system is ac-cessible from the CO, and administration of the system via LAN is pos-sible.



29/38

IP_Network.fm

P31003-H3570-G100-4-7631 , 2007-10-31




4.1.7 HiPath 5000 (Networked System) Variety - Merging HiPath 3000(Nodes)


1. Load the default data from HiPath 5000 Server in HiPath 3000 Managerwith File | HiPath 5000 | Transfer | HiPath 5000 Server. Select the ap-propriate HiPath 5000 Server via the Search button and then click theServer -> Manager button.

HiPath 3000 Ma-nager, ChapterTransfer | HiPath5000 Server

2. Add a new node to HiPath 3000 Manager with File | HiPath 5000 | New| HiPath 3000 and read out the CDB for the node with File | Transfer |System -> PC.Begin with the node with the smallest node ID and repeat for all nodes

available in the network.

HiPath 3000 Ma-nager, ChapterNew | HiPath 3000

3. Transfer the CDB(s) to the central database by selectingFile | HiPath 5000 | Transfer | HiPath 5000 Server | Add Node.


4. If HG 1500 is not recognized by the Feature Server, reset all boardsselected as gateways via Web-Based Management (or reset the sy-stem).Note:To add further nodes, perform the steps described above again.

HG 1500 Admin.,Chap. Icons in theWBM WindowsControl Area

5. Save the data back to the HiPath 5000 Server with File | HiPath 5000| Transfer | HiPath 5000 Server | Manager -> Server.




Status:All HiPath 3000 systems are logged on to HiPath 5000 Server and canbe managed centrally via HiPath 3000 Manager.


30/38


P31003-H3570-G100-4-7631 , 2007-10-31


IP_Network.fm


4.1.8 Licensing the Features

Some features must be licensed before you can use them. For example, these include the useof more than two B channels, the use of HiPath ComScendo services (additional IP clients such

as optiClient 130 or optiPoint 420), etc.

In this case you must install License Management, including a license agent (CLA), on a PC inthe network. The License Management software is available either on the software CD for Hi-Path 3000/5000 V7 or on a separate CD. After installation you can use License Managementto request a license file with the aid of the authorization code or MAC address of the HiPath3000 Control Board (CB). Details can be found in the License Management Online Help. Assoon as licensing is finished, you receive a license file, which is installed automatically in a sub-directory of the CLA (Customer License Agent). The licensing procedure must be repeated foreach HiPath 3000 system in the network. These files contain all of the data required for the sub-sequent distribution of the licenses for the features. This distribution of licenses is performed

using HiPath 3000 Manager.

In case of the HiPath 5000 V7 IP system (networked system):Because there is a HiPath 5000 Server in the network, you only receive a license file for theHiPath 5000 Server, which contains all licenses for the HiPath 3000 systems belonging to thenetwork.

>If the CLA and HiPath 3000 Manager are not on the same PC, the IP address of thePC on which the CLA is installed can be entered in a configuration file in theHiPath 3000 Manager directory.The configuration file (ass_150e.ini - Cla_Host) can be found in the directory

C:\Documents and Settings\Username\Application Data\Siemens\ Manager E.


Licensing the features with HiPath 3000 Manager

Perform the following steps for each HiPath 3000 system.

Requirement:

You have installed License Management, including a license agent, on aPC in the network and have requested and received the required licensefile(s) (xml file). You can check that the license file(s) for the license agenthas/have been transferred correctly with License Management.

HiPath 3000 Ser-

vice Manual, Li-censing Chapter


31/38

IP_Network.fm

P31003-H3570-G100-4-7631 , 2007-10-31




1. Using HiPath 3000 Manager, load the CDB from the desired HiPath

3000 path via File | Transfer | Communication | System -> PC.The options Read/write CDB and IP HiPath must be selected. As theIP address, select the IP address of the HiPath 3000 (in our example:1.150.1.231).

In case of the HiPath 5000 V7 IP system (networked system):Load the data from HiPath 5000 Server in HiPath 3000 Manager withFile | HiPath 5000 | Transfer | HiPath 5000 Server. Select the appro-priate HiPath 5000 Server via the Search button and then click theServer -> Manager button.

HiPath 3000 Ma-

nager, ChapterTransfer | Commu-nication

2. Under Settings | Licensing, select the HXG tab. The license agent(CLA) opens the license file that corresponds to the MAC ID (of the Hi-Path 3000 system).

HiPath 3000 Ma-nager, Chapter Li-censing

3. Check and/or change the number of licensed B channels (default:2 B channels) and the number of licensed system clients (default:0 system clients).Remark: system clients = HiPath ComScendo licensesNote:In the case of multiple HiPath 3000 systems, decide how you want todistribute the licenses to the individual systems.

HiPath 3000 Ma-nager, Chapter Li-censing


In the case of the HiPath 5000 V7 IP system (networked system) varie-ty:save the data back to the HiPath 5000 Server with File | HiPath 5000 |Transfer | HiPath 5000 Server | Manager -> Server.


HiPath 3000 Ma-nager, Chapter

Transfer | HiPath5000 Server


HiPath 3000 Ma-nager, ChapterSave CDB As....

6. In case of the HiPath 5000 V7 IP system (networked system):Using Web-Based Management, reset all HG 1500 boards(the alternative is a system reset).

HG 1500 Admin.,Chap. Icons in theWBM WindowsControl Area



32/38


P31003-H3570-G100-4-7631 , 2007-10-31


IP_Network.fm


Status:

The features are licensed and the current CDB is loaded in the system.

In case of the HiPath 5000 V7 IP system (networked system):The features are licensed in the network.



33/38

IP_Network.fm

P31003-H3570-G100-4-7631 , 2007-10-31




4.1.9 Configuring the IP Clients

IP clients are both system clients such as the IP system telephone optiPoint 420 or the softwareIP client optiClient 130 and S0/vCAPI stations such as H.323 clients or vCAPI clients. The IP

clients must be configured in the HiPath 3000 and then managed in the client software.


Configuration with HiPath 3000 Manager

1. Using HiPath 3000 Manager, load the CDB for the HiPath 3000 withFile | Transfer | Communication | System -> PC.The options Read/write CDB and IP HiPath must be selected. As the

IP address, select the IP address of the HiPath 3000 (in our example:1.150.1.231).


2. In the Station View, select the station (IP client).

3. Click the arrow symbol after the station number entry to change to theSet up Station | Stations dialog.

4. For each station, enter the station number, the extension (DID number)and the name. To save the changes, click Apply.

5. In the menu Settings | Set up Station, change to Gatekeeper: In the Gatekeeper tab, select the slot for the HG 1500 module.

Select the IP station from the Stations list. Specify whether the selected station is to be set up as a system

client, an H.323 client or an SIP client. Then click Set up. To savethe changes, click Apply.

Note 1:If you have already assigned names to the call numbers of the IP cli-ents (see 2.2.5), these names are displayed here.Note 2:If S0 stations are also to be configured on the Gatekeeper, the optionEnable Gateway Resources must be activated. Only then can theGateway tab be used to set up the S0 stations.

HiPath 3000 Ma-nager, ChapterGatekeeper

6. In the Gatekeeper tab, select the System Client for IP system tele-phones (e.g. optiPoint 420) and optiClient 130.

7. In the Gatekeeper tab, select the H.323 Client for H.323 clients andvCAPI stations.

8. In the Gatekeeper tab, select the SIP Client for SIP stations.Note:SIP stations do not require a fixed IP address.


34/38


P31003-H3570-G100-4-7631 , 2007-10-31


IP_Network.fm


9. In addition, when configuring H.323 clients:

In Station View, select the relevant H.323 client and click the Work-point Client tab. In the "IP address" field, select the option Fixed IPaddress and specify the IP address of the H.323 client.If an H.323 client is operated on the Gatekeeper, the Gatekeeper as-signs the call number and IP address. The IP address 0.0.0.0 must beconfigured in this case.Notes: Before assigning an IP address, use Ping to ensure that this

address has not already been assigned. If the parameter Analog adapter connected is activated, H.323

calls are carried out over a DSP and features are activated in thesystem.

HiPath 3000 Ma-

nager, ChapterStation View |Workpoint Clients





Status:The IP clients are configured in the HiPath 3000 and can be managed

using the software.

Example of administration of an IP telephone using theoptiPoint 420 with HiPath 3000 V7

1. Open the configuration menu on the telephone.-- on the optiPoint 420: press the keys 1, 0 and 3 simultaneously --The following appears in the telephone display:Administration:

01=Configuration?

2. Enter the password (standard for "Standalone": 123456) via01=Configuration? - Enter admin password



35/38

IP_Network.fm

P31003-H3570-G100-4-7631 , 2007-10-31




3. If a DHCP server is not being used, disable DHCP IP assignment via

01=Network? - 01=DHCP IP assign? - OFF

4. Enter the IP address of the IP client (e.g. 1.150.1.112) via02=Terminal IP addr.?

5. Enter the subnet mask of the IP client (e.g. 255.0.0.0) via03=Terminal mask?

6. Enter the IP address of the gateway (e.g. 1.150.1.10) via04=Default route?

7. Return to the main menu and restart the telephone via03=Start phone?

8. You should then start your browser and set up a connection with theterminal:Example: https://1.150.1.112Web-Based Management is started.

9. Click Administration and enter your password. Then click System fol-lowed by Gateway Settings. Configure the gateway address (gatekee-per module) and the subscriber number (IP clients station number).

10. To complete your settings, press Submit.The terminal now automatically logs onto the system.

Administration of an IP software client (H.323 client)

1. When configuring the IP client, specify the IP address of theHG 1500 as a gatekeeper!

Status:The IP clients are ready.



36/38


P31003-H3570-G100-4-7631 , 2007-10-31


IP_Network.fm


4.1.10 Further Configuration

Additional settings such as least cost routing (LCR), call pickup groups, or class of servicesmust be configured with HiPath 3000 Manager. These settings should only be made by trained

service personnel.

4.1.11 Connection to the Internet

You can establish an Internet connection using the HG 1500 board integrated in theHiPath 3000. Information on the different options available and instructions for configuring themare provided with examples in the document "HiPath 3000/5000 Feature Usage Examples,Chapter Practical Examples HG 1500".


37/38

GetstartedSIX.fm

P31003-H3570-G100-4-7631 , 2007-10-31

HiPath 3000/5000 V7, Getting Started Z-1

Nur fr den internen Gebrauch Index

Index Z

AAdministration 3-2analog trunk CLIP 1-2

BBackup Manager 2-7

CCall forwarding 1-1CLIP, analog trunk 1-2

CSTA monitoring 1-4

DDirect Payload to SIP provider 1-3Direct Payload to the Internet telephony ser-vice provider 1-3

EEFC 1-3Euro-ISDN Technology 2-2Extended Fast Connect 1-3

FFeature Description 2-6

HHG 1500 2-6HiPath 3000 IP System

delivery documents 3-1licensing 3-1numbering plan 3-1requirements specification 3-1

safety notes 3-1HiPath 3000 networked IP systems

assigning IP addresses 4-4configuring IP functionality 4-13hardware installation 4-1

HiPath 5000 ServerInstallation 4-3Merging Nodes 4-9

IInstallation and Startup 3-1Internet connection 4-16Internet Telephony Service Provider 1-5Introduction 2-1Inventory Manager 2-7ISDN numbering plan 1-1ITSP 1-5

K

Key modules 1-1

LLAN 3-2LDAP diagnosis 1-2License Management 4-10Licensing 4-10Lightning protection strip 1-4, 1-5

MManager E 2-6

Mobility Entry 1-4

NNumbering plan 1-1

OOpenStage 1-1

RRemote upgrade concept 1-2Route optimization 1-1

SService Manual 2-6SIP DDI 1-5Software Manager 2-7Startup 4-1STUN support 1-5Symbols 2-5System Description 2-6


38/38

Index Nur fr den internen Gebrauch

GetstartedSIX.fm

TT.38 via SIP 1-3Typographical conventions 2-5

UUpgrade Manager 2-7

VVarieties of HiPath 3000/5000

IP System (Networked System) 2-1IP System (Standalone) 2-1Networked IP Systems 2-1

Voice Mailbox 1-1

WWorkpoint Clients 2-2