High Speed Dome Camera - CCTVdirect Ltdleeds.cctvdirect.co.uk/DlDocs/Twilight/Manual/... · The Controller and Mini Speed dome make up the building blocks for any surveillance / security

EXPLANATION OF GRAPHICAL SYMBOLS

CAUTIONS

CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER(OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

CAUTIONS

RISK OF ELECTRIC SHOCK DO NOT OPEN

2

WARNINGS

TO PREVENT FIRE OR ELECTRIC SHOCK HAZARD, DO NOT EXPOSE

THIS APPLIANCE TO RAIN OR MOISTURE.

THE APPARATUS SHALL NOT BE EXPOSED TO DRIPPING OR SPLASHING

AND THAT NO DBJECTS FILLE WITH LIQUIDS, SUCH AS VASES,

SHALL BE PLACED ON THE APPARATUS.

The lighting flash with arrowhead symbol, within an triangle, is intended to alert the user

to the presence of uninsulated “dangerous voltage” within the product’s enclosure that

may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the

presence of important operating and maintenance (servicing) instruction in the literature

accompanying the appliance.

3

CE COMPLIANCE STATEMENT

FCC INFORMATION : THIS EQUIPMENT HAS BEEN TESTED AND FOUND TO COMPLY WITH THE LIMITS

FOR A CLASS A DIGITAL DEVICE, PURSUANT TO PART 15 OF THE FCC RULES. THESE LIMITS ARE

DESIGNED TO PROVIDE REASONABLE PROTECTION AGAINST HARMFUL INTERFERENCE WHEN THE

EQUIPMENT IS OPERATED IN A COMMERCIAL ENVIRONMENT. THIS EQUIPMENT GENERATES, USES,

AND CAN RADIATE RADIO FREQUENCY ENERGY AND IF NOT INSTALLED AND USED IN ACCORDANCE

WITH THE INSTRUCTION MANUAL, MAY CAUSE HAARMFUL INTERFERENCE TO RADIO COMMUNICATIONS.

OPERATION OF THIS EQUIPMENT IN A RESIDENTIAL AREA IS LIKELY TO CAUSE HARMFUL INTERFERENCE

IN WHICH CASE THE USER WILL BE REQUIRED TO CORRECT THE INTERFERENCE AT HIS OWN EXPENSE.

CAUTION : CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE FOR

COMPLIANCE COULD VOID THE USER’S AUTHOURITY TO OPERATE THE EQUIPMENT.

THIS CLASS A DIGITAL APPARATUS COMPLIES WITH CANADIAN ICES-003.

CET APPAREIL NUMERIQUE DE LA CLASSE A EST CONFORME A LA NORME NMB-003 DU CANADA.

WARNING

THIS IS A CLASS A PRODUCT. IN A DOMESTIC ENVIRONMENT THIS PRODUCT MAY CAUSE RADIO

INTERFERENCE IN WHICH CASE THE USER MAY BE REQUIRED TO TAKE ADEQUATE MEASURES.

4

* Please install the product on a completely flat floor.

- Always check the strength and stability of the installation location.

- Do not drop the appliacne on the floor. This may result in damage or injury.

* Do not attempt to disassemble the appliance. To prevent electric shock, do not remove

screws or covers.

- There are no user-servicecable parts inside. Contact qualified service personnel for

maintenance.

* Stop using the appliance if there appears to be any operational problem.

- Immediately turn the power off to the appliance if there is any abnormal condition such

as smoke or unusual smells.

- Continuing to use the appliance under abnormal conditions may result in serious damage.

* Always use the recommended power.

- Using incorrect power source ratings may result in fire, electric shock, or damage.

* Always handle the connection cable with care.

- Never damage or modify the connection cable.

- Do not pull, expose to heat, or place heavy objects on the connection cable.

- Non observance of these warnings may result in fire, electric shock or damage.

* Never use the appliance in places where there are flammable materials.

- Never use the appliance in places where flammable materials such as gas are used.

This may result in fire, explosion, and other serious accidents.

* Never touch un-insulated parts with wet hands.

- Touching un-insulated parts with wet hands may result in serious electric shock.

* Never expose the appliance to water or moisture.

- If the appliance gets wet, immediately turn the power off.

- Stop using the appliance if it gets wet. Contact the manufacturer immediately.

* Use the appliance indoors only.

- Do not place the appliance outdoors or expose it to rain or moisture.

- If dropped in water, the appliance may be corroded and damage.

* Do not use the appliance where there is excessive dust, smoke or moisture.

- Using the appliance under such conditions may result in fire, electric shock or

serious damage.

* If the controller body gets dirty, turn the power off and wipe the surface with a soft cloth

- Do not use chemical agents sudch as alcohol or benzene.

5

-WARNINGS AND CAUTIONS

-COMPLIANCE STATEMENT

-CE COMPLIANCE STATEMENT

-IMPORTANT SAFEGUARDS

- TABLE of CONTENT

- INTRODUCTION

- PACKAGE CONTENTS

- INSTALLATION & CONFIGURATION

--Basic configuration of Dome

--Rear View

--Swith Settings

--Before Installation

--Wall Mount Installation

--Ceiling Mount Installation

- External Interface

- DIMENSION

- SPECIFICATION

- OPERATION & PROGRAMMING

--Getting Started

--Basic Operations

--Title Edit

--Menu Tree

--System : Information

Reboot

Factory

Event Log

Password

--Display : OSD Setup

Area Title

Privacy Zone

Image Setup

--Dome : General

Motion

Home

Preset

Tour

Pattern

Scan

--Camera : Focus/Zoom

W - Balance

Exposure

Advanced Setup

--Alarm

- HOUSING & ACCESSORY

2

3

3

4

5

6

7

8

9

10

12

13

16

19

20

21

22

23

24

25

26

27

28

29

30

31

32

33

34

35

36

38

39

40

41

42

43

44

45

46

47

48

6

FEATURES

HIGH SPEED DOME

Lens

Power

Address Range

Preset

Tour

Pattern

Scan

Privacy Zone

Area Titles

Alarm

Protocol

Communication

Manual Speed

Preset Speed

Proportional Pan

36x, 26x, 18x Optical, 12x Digital

1/4 inch Sony EX-View HAD CCD

1~240 Position

8(Preset, Tour, Pattern and Scan)

8(Total 960 seconds)

8 including Vector Scan

32 zones (8 groups)

8

0.1 /sec ~ 360 /sec

Max 360 /sec

Yes

4 input(NO/NC)

Auto Protocol Recognition (Standard, Pelco-D, Pelco-P etc.)

RS-485 Half duplex. Max 4000 ft (1.2Km)

DC 12V (2.5V), AC 12V Optioal

99 ID (255 ID Optional)

The Controller and Mini Speed dome make up the building blocks for any surveillance / security system.

Using a multiple Controller and multiple dome cameras, no place is too large for monitoring and recording.

Extendable and flexible architecture facilitates remote control functions for a variety of external switching

devices such as DVR, Matrix switcher and Dome Camera.

Precautions for proper Operation

* Do not install the unit a place subject to direct sunlight, excessive moisture, dust or vibrations

where ventilation is poor.

* Please use the unit in the range of a guarantee temperature and humidity of operation.

* Please set ID of a camera as the same number as the input channel to DVR or Matrix switcher.

7

1. Dome camera Unit

2. Body (W/O Sunshield)

3. Trimring Bubble Dome

4. Wrench-3mm

5. User’s manual

OPTION

1. Wall Pipe Bracket

2. Ceiling pipe Bracket

3. Set Anchor(8 SET)

4. Sunshield

The following parts are supplied with the mini speed dome system.

Option

Wall Ceiling

8

Basic Configuration of Dome

Master Slave

CAM : 001 BAND

INPUT ? :

CAM : 001 BAND

INPUT ? :

T IN TC OL ORB RIG HTC ON T V1VO LU MEU ND ERS C AN S� VI DE O PO WE RV 2PM C 14H

9

Rear View

1 Pin description

2 Dip switch for protocol and band rate

3 Address switch

4 Alarm in/out

DC

On

ly

10

SWITCH SETTINGS

Before installation, please set the switches as described in this manual.

< Figure 1. Switches >

Protocols:

If you are going to use pelco-D, pelco-P protocols to communicate with the dome

system, you do not have to set any switches. The unit automatically detects these protocols. See Table A

for details.

<Table A. Protocols >

Switch1 Switch 2 Protocols

Off Off Pelco-D , Pelco-P, etc. Auto detect.

Off On Reserved

On Off Reserved

On On Reserved

DC Only

11

Baud rate:

Termination:

Default baud rate is 2400 bps. See Table B for details.

<Table B. Baud rate>

<Table C. Baud rate>

Switch 3 Switch 4 Baud rate (bps)

Off Off 2400 *default

Off On 4800

On Off 9600

On On 38400

See Table C for details.

Switch 5 Termination

Off Not Terminated

On Terminated

High Speed Dome system supports termination free RJ45 impedance matching.

12

remove the pan/tilt set screw

BEFORE INSTALLATION

Before installation, please remove the pan/tilt holder screw. Use the following steps.

1. Disassemble the 4 screws fixed in trimring.

2. Remove the fixed pan / tilt screws.

<Figure 2>

<Figure 3>

1. Disassemble the 4 fixed set screws.

2. Assemble RJ-45 cable.

3. Connect the alarm connector as this picture.

DC

On

ly

13

WALL MOUNT INSTALLATION

* Fix the TP 18 x 30L Screw supplied as the <Figure 4>

<Figure 4>

<Figure 5>

* Pass the cables through the bottom of the bracket.

21

14

* Hang the safety hook against drop on the bracket.

<Figure 6>

<Figure 7>

* Put the dome cable into the bracket and fix it.

15

* Fix the camera set by turning it clockwise as this picture.

(Notice : the cable against drop can be twisted)

* After coupling, fix the screws against ravelling by the wrench

supplied, complete it by molding of waterproof silicon

* Connect the camera set cable and the bracket cable, and put them into the bracket.

* Fix the steel cover supplied on the upper part of the bracket and complete fixing it by the

screw CM3 x 8L

<Figure 9>

<Figure 8>

16

* Fix the plastic anchors on the roof as this figure and fix the ceiling using the

screws supplied.

<Figure 10>

<Figure 11>

* Fix the pipe supplied as this figure turning it clockwise.

CEILING MOUNT INSTALLATION

17

* Hang the hook against drop on the ceiling bracket as this

figure, connect the camera set and the bracket cable and

fix it turning the camera set clockwise.

<Figure 12>

<Figure 13>

* Assemble the fixed screws using the wrench supplied

by molding of waterproof silicon as described in figure.

18

<Figure 14.1> with Sunshield <Figure 14.2> without Sunshield

19

Wire Gauge

<Table D> Interface Cable Wiring

<Table E Video Coaxial Cable Requirements>

Pin Color Function

1 WHITE/ORANGE VIDEO

2 ORANGE V-GND

3 WHITE/GREEN AC-/GND

4 BLUE DC/ +12V

5 WHITE/BLUE DC/ +12V

6 GREEN AC-/GND

7 WHITE/BROWN TRX-

8 BROWN TRX+

Cable Type Maximum Distance

RG 59/U 750 ft (229m)

RG 6/U 1,000ft (305m)

RG 11/U 1,500ft (457m)

* Cable requirement : 75-ohm impedance.

* All-copper center conductor.

* All-copper braided shield with 95% braid coverage

The following are the recommended maximum distances for 24 VAC applications and

are calculated with a 10 percent voltage drop. (Ten percent is generally the maximum

allowable voltage drop for AC-powered devices.

Power consumption is 21 VA per unit. Use a power source with a minimum of 21 VA per unit.

<Table F Wiring Distances>

Voltage 18 16 14 12

(1.0mm)

24VAC 215ft 341ft 542ft 863ft

DC

On

ly

External Interface (RJ-45)

20

DOME

WALL

CEILING

21

Camera

Image Sensor

Zoom (Model Specific)

Min Focus Distance

Scanning System

Frequency

Resolution

S/N Ratio

Video Output Signal

Minimum Illumination

Day & Night

White Balance

Video Output

Dome

Pan Angle / Speed

Tilt Angle / Speed

Preset Speed

Preset

Guard Tour

Pattern

Communication

Protocol

Auto Scan

Dome ID

Screen Display

General

Certification

Power Source

Operating Temperature

Operating Humidity

Material

Color

Dimension

Weight

1/4 - type Sony EX-View HAD CCD

36x Optical, f=3.4 to 122.4mm (F1.6~F4.5)



12x Digital Zoom

320mm(36x), 320(26x), 290(18x)

2:1 Interlace

NTSC : 15.734KHZ(H), 59.94HZ(V)

PAL : 15.625KHZ(H), 50HZ(V)

NTSC(Wide) : 530TV Lines(Min)

PAL (Wide) : 530TV Lines(Min)

More than 50dB

VBS 1.0V~p-p Composite (750hm Load)

0.1 Lux(36x), 0.09Lux(26x), 0.07Lux(18x) with ICR OFF

0.01 Lux with ICR ON

On, Off

Auto, ATW, Indoor, Outdoor, One-Push, Manual

CVBS : 1.0Vp-p / 75

360 Continuous Rotation, 0.1 ~360 / sec

-2 ~ 182 , 0.1 ~ 360 / sec (According to Zoom Speed)

Max. 360 /sec

1~240 Preset

8 Guard Tour (Preset, Pattern, Auto Scan, Tour Input)

8 Pattern, 960sec Memory

RS-485 Baud Rate : 2400 (Default) / 4800/9600/38400

Pelco-P, Pelco-D, Standard

8 Auto Scan

1~255 Camera ID

Camera ID, Pan / Tilt Angle, Flip, Zoom

CE, FCC, VCCI, ROHS, IP67

DC12V 2.5A (AC24V Optional)

-40 C~ 60 C (-40 F ~140 F)

0~90% RH (Non-Condensing)

Polycarbonate Bubble Dome / Aluminum Main Body. Vandal-Proof

Ivory / Black

233 x 235

Approx. 2200g

22

GETTING STARTED

This manual is designed to be a reference tool for the installation, programming and

operation of your system.

You need to install you system before using this manual. Refer to <installation> part

of this manual.

Once installed, apply power to the dome. The system will start a configuration sequence.

This information will remain on the monitor until dome operation begins. Refer to the following pages

to operate and program your dome system.

Note

1. Version can be changed by system upgrade.

2. Address changes with respect to ‘address switching setting’

3. Temperature can be changed by outside environment.

4. This manual is written by using E-ronix controller (ESC-200J)

23

Basic Operations

How to Control

Pan and Tilt Move joystick or press the direction keys left/right and up/down.

* Zoom Tele To zoom far, do the following:

1. Press the [TELE] button or turn the joystick clockwise until zoom stops at the 100X zoom limit

2. Release the button or joystick for one second.

3. To continue zooming (digitally), press the button or turn the joystick clockwise again until you

have the picture you want or reach the digital zoom limit.

* Zoom Wide Press the [WIDE] button or turn the joystick counterclockwise.

Preset Refer to <Preset> part of this manual.

Tour Refer to <Tour> part of this manual.

Pattern Refer to <Pattern> part of this manual.

Scan Refer to <Scan> part of this manual.

Privacy Zones Refer to the Zones section and to the documentation supplied with the control system.

24

ACCESSING MAIN MENU (Menu/Preset 95)

When you use PD or PP protocol with your controller, you can access the main menu

by programming (saving or calling) preset 95.

When you use STANDARD or any other protocols, do the followings:

1. Enter the number of the dome and press the CAM key.

2. Press the MENU key. The main menu appears.

To edit a title:

1. Use the joystick to position the cursor beside TITLE.

2. Move the joystick right. The following appears on the monitor.

3. Use the joystick right, left, up and/or down to select a character. Press [TELE] button or twist

the joystick clockwise to input a character.

4. Press [WIDE] button or twist the joystick counterclockwise to delete a character.

5. Follow the directions displayed on the monitor.

6. When the label is completed, press [ENT] or [IRIS OPEN] to return to the previous menu.

7. To cancel editing a title, press [CLR] or [IRIS CLOSE] to return to the previous menu.

TITLE:

ABCDEFGHIJKLMNOP

QRSTUVWXYZabcdefg

hijklmnopqrstuvwx

yz0123456789<>/-:

■ Select: <MOVE>

■ Save: <ENT> <OPEN>

■ Exit: <CLR> <CLOSE>

TITLE EDIT

*This title edit menu can be used in OSD Setup/Pattern/Scan/Preset/Area Title commonly.

25

MENU TREE

SYSTEM

DISPLAY

DOME

CAMERA

ALARM (p.47)

EXIT

OSD SETUP (p.31)

AREA TITLES (p.32)

PRIVACY ZONE (p.33)

IMAGE SETUP (p.34)

FOCUS/ZOOM (p.43)

W-RALANCE (p.44)

EXPOSURE (p.45)

ADVANCED (p.46)

INFO (p.26)

REBOOT (p.27)

FACTORY (p.28)

EVENT LOG (p.29)

PASSWORD (p.30)

GENERAL (p.35)

MOTION (p.36)

PRESET (p.38)

TOUR (p.40)

PATTERN (p.41)

SCAN (p.42)

26

SYSTEM: INFO

The system Information displays serial number/model name/ Running

version/Protocol/Communication Type/Address switch No./Temperature.

System settings cannot be edited in this menu. This screen

is for reference only.

Use the following steps to display the system information screen:

1. Push the MENU key(refer to ‘Accessing main menu’in page 38)

2. Use the joystick to position the cursor beside SYSTEM.

3. Move the joystick right.

4. Select INFO using joystick.

Note

-Version can be changed by system upgrade.

-Address changes with respect to ‘address switching setting’

-Temperature can be changed by outside environment.<< SYSTEM INFORMATION >>

██████████████████████████S/N:0-00-00-000-00000MODEL : XXX-XXXXVERSION : XXX-XXXXVIDEO : 1.58EMPROTOCOL : STANDARDCOMM. : RS485/02400ADDRESS : 001TEMP. : 044.0C/111.2F██████████████████████████■ Exit: <CLR> <CLOSE>

██████████████████████████►SYSTEM > INFO

DISPLAY > REBOOTDOME > FACTORYCAMERA > ALARMEXIT

<<<<< Main MENU >>>>>

██████████████████████████►SYSTEM >

DISPLAY >DOME >CAMERA >ALARMEXIT

<<<<< Main MENU >>>>>

27

SYSTEM: Reboot

Reboot the system if it does not operating or if it is not available

for control.

Rebooting the system will cycle power without changing

programmed dome settings.

Use the following steps to display the System Information screen:

1. Press the MENU key(refer to ‘Accessing main menu’ in page 38)

2. Select SYSTEM using joystick.

3. Select REBOOT using joystick in the sub menu of SYSTEM.

4. To Reboot the system, Press [ENT] or [OPEN].

To cancel reboot, Press [CLR] or IRIS [CLOSE] key.

■ Reboot: <ENT> <OPEN>■ Exit: <CLR> <CLOSE>

██████████████████████████►SYSTEM > INFODISPLAY > ►REBOOTDOME > FACTORYCAMERA >ALARMEXIT

██████████████████████████►SYSTEM >

DISPLAY >DOME >CAMERA >ALARMEXIT

<<<<< Main MENU >>>>>

<<<<< Main MENU >>>>>

28

SYSTEM: FACTORY

Use this function to reset all camera settings to factory default parameters.

You can reset a specific setting to factory default parameters.

Use the following steps to display the System Information screen:

1. Press the MENU key (refer to ‘Accessing main menu’ in page 38)


3. Select FACTORY in the sub menu of SYSTEM using joystick.

4. Select items to be reset.

5. Press [ENT] button or move the cursor to<SAVE and exit>

and then move the joystick right.

ALL: Restores all save items (CAM/PRESET/TOUR/PATTERN/

SCAN settings)

CAM: Reset Camera related settings.

PRESET: Reset Saved presets.(To reset specific preset, refer to

Preset PRESET in chapter 35)

TOUR: Reset Saved Tours.

PATTERN: Reset Saved pattern.

SCAN: Reset Saved Scan items.

██████████████████████████►SYSTEM > INFO DISPLAY > REBOOTDOME > ►FACTORY CAMERA > ALARM EXIT

██████████████████████████►SYSTEM >

DISPLAY >DOME >CAMERA >ALARM EXIT

<<<<< Main MENU >>>>>

<<<<< Main MENU >>>>>

<< FACTORY SETUP >>██████████████████████████►ALL : OFF

CAM : OFF PRESET : OFF TOUR : OFF PATTERN : OFF SCAN : OFF██████████████████████████ <Save and Exit> <Exit without Saving>

29

SYSTEM: EVENT LOG

Event Log shows the current dome status and dome event logs.

If the dome have some problems, it displays error signal and save

the logs to EEPROM. Turn SELF TEST on to monitor the dome’s

status and save all event logs. See <DOME:GENERAL> for

SELF TEST descriptions.

Use the following steps to display the EVENT LOG screen:



3. Select EVENT LOG in the sub menu of SYSTEM using joystick.

4. Code : <number> means number of error occurred during

camera operation.

When you scroll up and down using joystick, you can find what

kinds of error have occurred during operation.

5. Press the [ESC] or [IRIS CLOSE] key to return previous menu.

<<<<< Main Menu >>>>>██████████████████████████►SYSTEM > DISPLAY > DOME > CAMERA > ALARM EXIT

<<<<< Main Menu >>>>>██████████████████████████►SYSTEM > INFO. DISPLAY > REBOOT DOME > FACTORY CAMERA > ►EVENT LOG ALARM PASSWORD EXIT

<<<< EVENT LOG >>>>██████████████████████████Code:0000,Cnt:00,Drp:000Current Status-----------------------

██████████████████████████Exit: <CLR> <CLOSE>

<<<< EVENT LOG >>>>██████████████████████████Code:0000,Cnt:00,Drp:000

None............

-----------------------

►01.00 Empty........... 02.00 Empty........... 03.00 Empty........... 04.00 Empty........... 05.00 Empty...........██████████████████████████Exit: <CLR> <CLOSE>

30

SYSTEM: PASSWORD

Use this function to

The dome features password protection to prevent unauthorized

changes to the dome settings. An operator cannot access any of

the Dome Settings menus.

Controller/keyboard commands cannot override password-protected

settings. If a keyboard is used to set a preset, pattern, or zone,

the Enter Password screen appears on the monitor.

The password must be entered before programming can continue.

Four characters must be entered to create a valid password.

Use the following steps to set up password:



3. Select PASSWORD in the sub menu of SYSTEM using joystick.

4. Select number using joystick left/right and press the TELE key

or twist joystick.

clockwise to input. Repeat this action to fill current/new/confirm

password.

5. To enable password set ENABLE:ENABLED

Note

-The default password is “0000”

-When you initialize the system with <SYSTEM:FACTORY>,

password will be removed.

<<<<< Main Menu >>>>>██████████████████████████►SYSTEM > DISPLAY > DOME > CAMERA > ALARM EXIT

<<<<< Main Menu >>>>>██████████████████████████►SYSTEM > INFO. DISPLAY > REBOOT DOME > FACTORY CAMERA > EVENT LOG ALARM ►PASSWORD EXIT

PASSWORD██████████████████████████ ►CURRENT: x--- NEW : ---- CONFIRM: ---- ENABLE : DISABLED██████████████████████████ x12456789

31

DISPLAY: OSD SETUP

OSD setup allows you to program how labels are displayed onthe monitor.

The following labels are available:TITLE Identifies area and operation titles.TIME Identifies dwell time.ZOOM Identifies the amount of magnification.ID Identifies dome address.MODE Identifies dome operation mode.ANGLE Amount of pan/tilt from 0°.

The zoom ratio label is displayed when zoom is activated.The following settings are available for each label:OFF Label is not displayed when activated.ON The label is continually displayed.xx SEC The label is displayed for xx seconds after activation.

Labels can be placed anywhere on the monitor. This feature allows you to customize the appearance of your monitor screen.

To set a label position:1. Press the MENU key (refer to ‘Accessing main menu’ in page 38).2. Select DISPLAY and select OSD SETUP using joystick.3. Press the [TELE] button or turn the joystick clockwise.4. Use the joystick to move the label up, down, left and/or right.5. Press [ENT] or [IRIS OPEN] key.6. Repeat steps 1 through 4 to position other labels.7. Select <Save and Exit> to save settings and exit menu.8. Select <Exit without Saving> to exit menu without saving settings.

*Note -Press [ENT] or [IRIS OPEN] key to save settings and exit to previous menu. Press [Esc] or [IRIS CLOSE] key to go to previous menu without saving any settings at any time.

██████████████████████████SYSTEM > ►DISPLAY > ►OSD SETUP DOME > AREA TITLES CAMERA > PRIVACY ZONE ALARM IMAGE SETUPEXIT

██████████████████████████SYSTEM >►DISPLAY >

DOME > CAMERA > ALARM EXIT

████████████████████████

<<<<< Main MENU >>>>>

<<<<< Main MENU >>>>>

<< OSD SETUP >>██████████████████████████►TITLE : OFF

TIME : OFF ZOOM : 3 SEC ID : ON MODE : ON ANGLE : 3 SEC██████████████████████████ <Save and Exit> <Exit without Saving>

Twist joystick clockwise

or press [TELE] button

32

█ Start Position Setup

█ Press MOVE Key█ Save: <ENT> <OPEN>█ Exit: <CLR> <CLOSE>

██████████████████████████SYSTEM > ►DISPLAY > OSD SETUPDOME > ►AREA TITLESCAMERA > PRIVACY ZONEALARM IMAGE SETUPEXIT

DISPLAY: AREA TITLES

A zone is a pan area, defined by a left and right limit on the pan plane.

The dome system is capable of 8 area titles, each with a 12 character

label

To program a zone:

1. Press the MENU key(refer to ‘Accessing main menu’ in page 38)

2. Select DISPLAY and select AREA TITLE usig joystick.

3. Use the joystick to position the cursor beside NO.xxx. Move left or

right to select zone ID. Press the [TELE] button or turn the joystick

clockwise to setup START and STOP pan limit angle.

4. Move the joystick to position start limit angle, Press [ENT] or

[IRIS OPEN] to save START limit angle.

5. Move the joystick to position start limit angle, Press [ENT] or

[IRIS OPEN] to save STOP limit angle.

6. Edit a title, See [TITLE EDIT] section for detail.

To clear an area title:

1. Press the MENU key (refer to ‘Accessing main menu’in page 38)

2. Select DISPLAY and select AREA TITLE using joystick.

3. Use the joystick to position the cursor beside NO.xxx.Move left or

right to select zone ID.

4. Press the [WIDE] or turn the joystick counter clockwise to clear

area title.

*Note

- after saving area titles, turn on the TITLE menu in the

<DISPLAY:OSD SETUP> to view the area title.

*Note

- Press [ENT] or [IRIS OPEN] key to save settings and exit

to previous menu. Press [Esc] or [IRIS CLOSE] key to go to

previous menu without saving any settings at any time.

<< AREA TITLE SETUP >>██████████████████████████►NO.001 : █ TITLE : -START : -STOP : ██████████████████████████ <Save and Exit> <Exit without Saving>

<<<<< Main MENU >>>>>



33



DISPLAY: PRIVACY ZONE

A privacy zone allows a user to program one four-sided, user-defined

area that cannot be viewed by the operator of the dome system. The

blanked area will move with pan and tilt functions and automatically

adjust in size as the lens zooms telephoto and wide

1.Group no : Identifies group ID. Can have 1~8

2. No. xxx : Identifies privacy zone ID. Can have 1~4

3. Mode : DSABLE - disable privacy zone

BLOCK - Enable privacy zone

4. Privacy Mask : adjust mask size

3-1 : PAN/TILT - adjust position

3-2 : TELE - enlarge mask size

3-3 : WIDE - make mask size small

To program a privacy zone:


2. Select DISPLAY and select PRIVACY ZONE using joystick.


right to select zone ID. Press the [TELE] button or turn the joystick

clockwise to setup a zone.

4. Follow the instructions that appear on the screen.

5. The Privacy Zone menu reappears with a saved marked (█) option.

To disable or clear a Privacy Zone (a zone is enabled automatically

when it is programmed):

1. Use the joystick to position the cursor beside NO.xxx.Move left or

right to select zone ID.

2. Press the [WIDE] button or turn the joystick counterclockwise to clear.

*NOTE Press [ENT] or [IRIS OPEN] key to save settings and exit

to previous menu or Press [Esc] or [IRIS CLOSE] key to go to


<<<<< Main Menu >>>>>██████████████████████████ SYSTEM > ►DISPLAY > OSD SETUP DOME > AREA TITLES CAMERA > ►PRIVACY ZONE ALARM IMAGE SETUP EXIT

<< PRIVACY ZONE SETUP >>██████████████████████████ GROUP : 1►NO.001 : █ MODE : DISABLE██████████████████████████ <Save and Exit> <Exit without Saving>


34

<<<<< Main Menu >>>>>██████████████████████████ SYSTEM > ►DISPLAY > OSD SETUP DOME > AREA TITLES CAMERA > PRIVACY ZONE ALARM ►IMAGE SETUP EXIT

<< IMAGE SETUP >>██████████████████████████►MIRROR : OFF██████████████████████████ <Save and Exit> <Exit without Saving>

DISPLAY: IMAGE SETUP

This menu allows operator to change of displayed image settings

The following four options are available:

OFF normal image

H.MIRROR left-right reversal image

V.MIRROR upside-down image

REVERSE left-right reversal and upside-down image

To set up image display


2. Select DISPLAY and select IMAGE SETUP using joystick.

3. Select one of four possible settings.

*Note

-Press [ENT] or [IRIS OPEN] key to save settings and exit



35

<<<<< Main Menu >>>>>██████████████████████████ SYSTEM > DISPLAY > ►GENERAL►DOME > MOTION CAMERA > HOME ALARM PRESET EXIT TOUR PATTERN SCAN

<< GENERAL SETUP >>██████████████████████████►BACKUP TASK : ON

TURBO SPEED : OFF PRESET SPEED: FAST SELF TEST : OFF UNIV. DWELL : OFF██████████████████████████ <Save and Exit> <Exit without Saving>

DOME: GENERAL SETUP

This menu control general dome related function.

Detail description is as follow.

BACKUP TASK

Dome ID is generally assigned with address switch, but using this

menu you can assign the dome ID with S/W.

BACKUP TASK

This setting defines a specific(preset, tour, pattern and scan) activity

to be performed in the event the power to the dome is cycled or after

alarm action.

The following settings are available:

OFF No action.

ON (default) The dome resumes its prior activity.

TURBO SPEED

This setting defines the manual pan and tilt speed.


OFF (default) Max speed is 90 degrees per second.

ON Max speed is 400 degrees per second.

*Note- Turbo speed only applicable to manual operation

not for preset, pattern etc.

PRESET SPEED

You can optimize preset speed with this menu.

There are three options:

FAST : 400 deg / sec

NORMAL : 300 deg / sec

SLOW : 200 deg / sec

SELF TEST

This setting defines the diagnostic monitoring activity.

When the dome finds some problems, the error signal is displayed.

For details, see <SYSTEM:EVENT LOG> section in this manual.


OFF (default) Disable selftest

ON Enable selftest

UNIV. DWELL(UNIVERSAL DWELL TIME)

Set the dome’s dwell time universally regardless of setting dwell time of any other activity (preset, scan etc.)

OFF Disable universal swell time

3~239 set the universal dwell time with this value.

36

<<<<< Main Menu >>>>>██████████████████████████ SYSTEM > DISPLAY > GENERAL►DOME > ►MOTION CAMERA > HOME ALARM PRESET EXIT TOUR PATTERN SCAN

<< MOTION SETUP >>██████████████████████████►PROP. PAN/TILT: ON AUTO FLIP : ON OVER TILT : ON AZIMUTH ZERO : OFF LIMIT STOP : OFF -LEFT LIMIT : -RIGHT LIMIT :██████████████████████████ <Save and Exit> <Exit without Saving>

DOME: MOTION

PROPORTIONAL PAN/TILT

Proportional pan/tilt automatically reduces or increases the pan and

tilt speeds in proportion to the amount of zoom. At telephoto zoom

settings, the pan and tilt speeds will be slower for a given amount of

joystick deflection than at wide zoom settings.

There are two proportional pan/tilt modes:

ON (default) Enables the proportional pan/tilt mode.

OFF Disables proportional pan/tilt mode. The pan/tilt speed will not

depend on the amount of zoom.

AUTO FLIP

When the camera tilts downward and goes just beyond the vertical

position, the dome rotates 180 degrees. When the dome rotates

(flips), the camera starts moving upward as long as you continue to

hold the joystick in the down position. Once you let go of the joystick

after the dome rotates, joystick control returns to normal operation.

ON (default) Auto flip mode is enabled.

OFF Auto flip mode is disabled.

OVER TILT

To prevent horizontal view cut with trim ring or ceiling, this menu restrict

horizontal view angel.

ON restrict minimum tilt angle to 4.5 degree

OFF minimum tilt angel is 0 or below 0.

AZIMUTH ZERO

Azimuth zero is the pan angle from 0° to 359°. Azimuth zero is the pan

position you specify to be the 0° point. Azimuth zero is normally set to

magnetic north. Once set, azimuth is based on the set Azimuth zero

point.

To set Azimuth zero:

1. Use the joystick to position the cursor beside AZIMUTH ZERO.

2. Press [TELE] or twist the joystick clockwise.


To clear Azimuth zero:

1. Use the joystick to position the cursor beside AZIMUTH ZERO.

2. Press [WIDE] or twist the joystick counterclockwise.

37

DOME: MOTION

LIMIT STOP

Limit stops are programmable stops that limit the pan range of the dome.

There must be two limits, a left and a right, to define an area. A manual

(joystick) pan operation stops when a limit stop is reached.

To set limit stops:

1. Use the joystick to position the cursor beside LIMIT STOP.

2. Press [TELE] or twist the joystick clockwise.


To clear limit stops, set limit stop mode to OFF.

1. Use the joystick to position the cursor beside LIMIT STOP.

2. Press [WIDE] or twist the joystick counterclockwise.

<< MOTION SETUP >>██████████████████████████ PROP. PAN/TILT: ON AUTO FLIP : ON OVER TILT : ON AZIMUTH ZERO : OFF►LIMIT STOP : OFF -LEFT LIMIT : -RIGHT LIMIT :██████████████████████████ <Save and Exit> <Exit without Saving>

38

<<<<< Main Menu >>>>>██████████████████████████ SYSTEM > DISPLAY > GENERAL►DOME > MOTION CAMERA > ►HOME ALARM PRESET EXIT TOUR PATTERN SCAN

<< HOME SETUP >>██████████████████████████►ACTION : HOME

NUMBER : TIME : 120 min MODE : AUTO██████████████████████████ <Save and Exit> <Exit without Saving>

DOME: HOME

This feature defines what activity should be executed after assinged

idle time.

ACTION / NUMBER

HOME (default) HOME action.

PRESET [NUMBER] Dome goes to preset [NUMBER].

TOUR [NUMBER] Runs tour [NUMBER].

PATTERN [NUMBER] Dome starts pattern [NUMBER] .

SCAN [NUMBER] Dome goes to scan [NUMBER].

*Note

-In order to call action preset, tour, pattern or scan, you must save

preset, tour, pattern or scan first.

TIME

This feature allows the dome to begin a user specific action after a

programmed time of inactivity. Home time can be programmed from

1 minute to 240 minutes (4 hours).

MODE

AUTO (default) Enabled HOME function.

MANUAL Disables this feature.

39

<<<<< Main Menu >>>>>██████████████████████████ SYSTEM > DISPLAY > GENERAL►DOME > MOTION CAMERA > HOME ALARM ►PRESET EXIT TOUR PATTERN SCAN

<< PRESET SETUP >>██████████████████████████►NO.001 : Empty

TITLE : DWELL : -PTZ : ██████████████████████████ <Save and Exit> <Exit without Saving>

DOME: PRESET

The dome system has 240 preset positions. Each of the user-definable

presets can be programmed to use pan, tilt and camera settings.

Use the following steps to program a preset.


right to select preset ID.

2. Press the [TELE] button or turn the joystick clockwise to edit a

preset scene.


4. The PRESET SETUP menu reappears with a Saved option.

5. Edit a title. See [TITLE EDIT] section for details.

6. Edit a dwell time.

To clear a preset:

1. Use the joystick to position the cursor beside NO.xxx. Move the

joystick left or right to select a preset ID.

2. Press the [WIDE] button or turn the joystick counterclockwise to

clear a preset.

*NOTE Press [ENT] or [IRIS OPEN] key to save settings and exit


previous menu without saving any settings at any time.█ Start Position Setup


40

<<<<< Main Menu >>>>>██████████████████████████ SYSTEM > DISPLAY > GENERAL►DOME > MOTION CAMERA > HOME ALARM PRESET EXIT ►TOUR PATTERN SCAN

<< TOUR SETUP >>██████████████████████████►NO.001 : Empty

=== === === === === ===

=== === === === === ===

=== === === === === ===

=== === === === === ===

=== === === === === ===

██████████████████████████ <Save and Exit> <Exit without Saving>

DOME: TOUR

The dome system has 8 guard tours. Each of the tour has 30 items.

Each item can have pre-defined preset, pattern, scan and any other tour.

To program a tour.

1. Press the MENU key (refer to ‘Accessing main menu’ in page 38).

2. Select DOME and select Tour using joystick.


right to select tour ID. Press the [TELE] button or turn the joystick

clockwise to setup.

4. To insert items. use following steps:

a. Move the joystick to position the cursor beside XXX.

b. Press the [TELE] button or turn the joystick clockwise to select an

action (PRESET, TOUR, PATTERN and/or SCAN) and number.


6. Before select a specific item, save it first.

To disable or clear a tour.

1. Use the joystick to position the cursor beside NO. xxx. Move left or

right to select tour ID.

2. Press the [WIDE] button or turn the joystick counterclockwise to clear.

41

DOME: PATTERN

A pattern is a memorized, repeating, series of pan, tilt, zoom and preset

functions that can be called with a command from a controller or

automatically by a programmed function.

The dome system can have maximum 8 user-defined patterns.

To program a pattern:


2. Select DOME and select PATTERN using joystick.

3. Use the joystick to position the cursor NO.xxx. Move left or right

to select pattern ID.

4. Press the [TELE] button or turn the joystick clockwise to start to learn.


6. To finish learning, press [ENT] or [IRIS OPEN] key.

To cancel learning, press [CLR] or [IRIS CLOSE] key.

7. Edit title. Refer to [TITLE EDIT] section in this manual.

To clear a pattern:


joystick left or right to select a pattern ID.

2. Press the [WIDE] key or turn the joystick counterclockwise.

*You can access this pattern setting menu with [PTRN] key in ESC-200J controller.

<<<<< Main Menu >>>>>██████████████████████████ SYSTEM > DISPLAY > GENERAL►DOME > MOTION CAMERA > HOME ALARM PRESET EXIT TOUR ►PATTERN SCAN

<< PATTERN SETUP >>██████████████████████████►NO.001 : █ TITLE : -TIME : ██████████████████████████ <Save and Exit> <Exit without Saving>

42

DOME: SCAN

Scan is a pan and tilt functions from one point to another point.

The dome has 8 user-defined auto scans.

To program a scan:


2. Select DOME and select PATTERN using joystick.


right to select a scan number.

4. Press the [TELE] key or turn the joystick clockwise to start to

setup start and stop position.

5. Edit a title. Refer to [TITLE EDIT] section in this manual.

6. Select scan speed. Scan speed is the degrees per second that

the dome will pan when in a scan mode. The range of scan speed is

from 1 to 9 the default value is 5.

*When the start and stop position are same, scan mode is changed to

ENDLESS automatically. Any other case, the mode is

COMING & GOING

To clear a scan:


joystick left or right to select a scan number.

2. Press the [WIDE] key or turn the joystick counterclockwise.

How to activate a scan

Press the specific number key and then press [SCAN]. ex) [1]+[SCAN]

You can also access this menu with [SCAN] key.

*Note

Press [ENT] or [IRIS OPEN] key to save settings and exit

to previous menu or Press [Esc] or [IRIS CLOSE] key to go to


<<<<< Main Menu >>>>>██████████████████████████ SYSTEM > DISPLAY > GENERAL►DOME > MOTION CAMERA > HOME ALARM PRESET EXIT TOUR PATTERN ►SCAN

<< SCAN SETUP >>██████████████████████████►NO.001 : █ TITLE : SPEED : 5 DWELL : 005 sec. -MODE : -START : -STOP :██████████████████████████ <Save and Exit> <Exit without Saving>

43

<<<<< Main Menu >>>>>██████████████████████████ SYSTEM > DISPLAY > DOME > ►FOCUS/ZOOM►CAMERA > W-BALANCE ALARM EXPOSURE EXIT ADVANCED

<< FOCUS/ZOOM SETUP >>██████████████████████████►FOCUS : TRIGGER

AF.SENSI : NORMAL D.ZOOM : ON██████████████████████████ <Save and Exit> <Exit without Saving>

CAMERA: FOCUS/ZOOM

FOCUS

There are three auto focus settings:

AUTO If auto focus mode is set to auto. The camera will focus

automatically.

MANUAL Focus is operated manually. To focus, press [NEAR] or

[FAR] key on the controller.

TRIGGER (default) If auto focus mode is set to TRIGGER, the camera

will focus when zoom functions.

*Note

Auto focus will malfunction at below condition.

- very dark or shiny area

- when slow shutter is activated

- area which doesn’t have contrast difference

AF.SENSI (Auto Focus Sensitivity)

AF sensitivity can be set to either Normal or Low.

NORMA Reaches the highest focus speed quickly. Use this when

shooting a subject that moves frequently. Usually this is the most

appropriate mode.

LOW Improves the stability of the focus. When the lighting level is low,

the AF function does not take effect, even though the brightness varies,

contributing to a stable image.

D. ZOOM(Digital Zoom)

To enable digital zoom, set D.ZOOM to ON.

The default value is ON.

*Note

Press [ENT] or [IRIS OPEN] key to save settings and exit to previous menu.

Press [Esc] or [IRIS CLOSE] key to go to previous menu without saving any settings at any time.

44

CAMERA: W - BLANCE

This feature automatically processes the viewed image to retain color

balance over temperature range. The default setting for

white balance is auto.

White Balance has following four modes.

AUTO

This mode computes the white balance value output using color

information from the entire screen. It outputs the proper value using

the color temperature radiating from a black subject based on a

range of values from 3000 to 7500K.

INDOOR

Automatic White Balance for in door. 3200K base mode.

OUTDOOR

Automatic White Balance for outdoor. 5800K base mode.

ONEPUSH

The One Push White Balance mode is a fixed white balance mode that

may be automatically readjusted only at the request of the user

(One Push Trigger).

ATW

Auto Tracing White Balance (2000 to 10000K).

MANUAL

Manual White Balance. Manual control of R and B gain, 256 stepes each.

*Note

: Auto white balance will malfunction at below condition.

- Very dark or shiny area (clear sky, sunset)

- Direct shot of fluorescent lamp or much difference brightness area

*Note

Press [ENT] or [IRIS OPEN] key to save settings and exit to previous menu or Press [Esc] or

[IRIS CLOSE] key to exit to previous menu without saving any settings at any time.

<<<<< Main Menu >>>>>██████████████████████████ SYSTEM > DISPLAY > DOME > FOCUS/ZOOM►CAMERA > ►W-BALANCE ALARM EXPOSURE EXIT ADVANCED

<< WB SETUP >>██████████████████████████►MODE : AUTO

R GAIN : B GAIN :██████████████████████████ <Save and Exit> <Exit without Saving>

45

CAMERA: EXPOSURE

The variety of Auto Exposure functions, which allow video signal to

output the optimum image for subjects from low light condition,

to high light conditions, is available.

FULL AUTO

Auto Iris and Gain, Fixed shutter speed (NTSC : 1/60, PAL: 1/50)

Shutter Priority

Variable shutter speed, auto Iris and Gain (1/1 to 1/10000 sec)

Flicker can be eliminated by setting shutter to

1/100 for NTSC model used in countries with 50 Hz power

supply frequency.

1/120 for PAL model used in countries with 60 Hz power

supply frequency.

Iris Priority

Variable Iris (F 1.6 to Close, 18 steps), Auto Gain

and Shutter speed.

Manual

Variable Shutter, Iris and Gain

*Note

If auto iris is in the auto mode, it will remain that way until the Iris is

manually opened or closed. The dome will return to auto mode when it is panned or tilted.

<<<<< Main Menu >>>>>██████████████████████████ SYSTEM > DISPLAY > DOME > FOCUS/ZOOM►CAMERA > W-BALANCE ALARM ►EXPOSURE EXIT ADVANCED

<< AE SETUP >>██████████████████████████►MODE : FULL AUTO

IRIS : SHUT : GAIN : BRIGHTNESS :██████████████████████████ <Save and Exit> <Exit without Saving>

46

CAMERA: ADVANCED SETUP

SHARPNESS

Settings ranges from 0 to 15. Enhances picture detail by increasing

the aperture gain of the camera and sharpening the edges in the picture.

BACKLIGHT(BLC)

Backlight compensation enhances objects in the center of the picture.

The dome uses the center of the picture to adjust the iris. If there is a

bright light source outside of this area, it will wash out to white. The

camera will adjust the iris so that the object in the sensitive area is

property exposed.

OFF (default) Backlight compensation is not activated.

ON Backlight compensation is activated.

DAY & NIGHT

Auto ICR Mode automatically switches the settings needed for

attaching or removing IR Cut filter.

LINE SYNC

INTERNAL

An internal oscillator inside camera generates a synchronizing signal as a basic oscillator.

NTSC = 28.636363MHz

PAL = 17.7344MHz

EXTERNAL

When a TTL level V-Lock pulse is input, the camera synchronizes to the input signal (V-locksynchronization).

When using camera with AC power supplier, this mode can be used.

<<<<< Main Menu >>>>>██████████████████████████ SYSTEM > DISPLAY > DOME > FOCUS/ZOOM►CAMERA > W-BALANCE ALARM EXPOSURE EXIT ►ADVANCED

<< ADVANCED SETUP >>██████████████████████████►SHARPNESS : 04 BACKLIGHT : OFF DAY&NIGHT : ON LINE SYNC : INTERNAL -PHASE : ██████████████████████████ <Save and Exit> <Exit without Saving>

47

ALARM

IN(ALARM INPUT)

NO Normal Open.

NC Normal Close.

OUT(ALARM OUTPUT)

OFF (default) No action.

ON

PRIORITY

Alarm priority.

ACTION/NUMBER

Alarm activates various surveilance modes

with preset, tour, pattern and scan.

TIME

Alarm activation time.

To disable an alarm:


joystick left or right to select a alarm number.

2. Press the [WIDE] button or turn the joystick counterclockwise to

clear an alarm.

<< ALARM SETUP >>██████████████████████████►NO.001 : █ IN : OUT : PRIORITY: ACTION : NUMBER : DWELL : ██████████████████████████ <Save and Exit> <Exit without Saving>

<<<<< Main Menu >>>>>██████████████████████████ SYSTEM > DISPLAY > DOME > CAMERA > ►ALARM EXIT

48

Camera

Wall Mount Bracket

Ceiling Mount Bracket

49

A VIEW�APole Mount Bracket

Coner Mount Bracket

50

Roof Mount Bracket

Swan Mount Bracket

51

Parapet Wall Mount Bracket

Parapet Roof Top Mount Bracket

Documents

High Speed Dome Camera - CCTVdirect Ltdleeds.cctvdirect.co.uk/DlDocs/Twilight/Manual/... · The Controller and Mini Speed dome make up the building blocks for any surveillance / security