High Power LED K Series LED - GSEO · GP K series LED Datasheet ... High Power LED GP ® K Series LED ... 1 Unlimited ≦30 ℃/85 ％RH 168 +5/0 85 ℃ / 85 ％RH Table 7.1 Moisture

GP K series LED Datasheet (05/05/09) – V03 1

High Power LED

GP® K Series LED

Introduction

GSEO GP K series LED is an energy efficient and ultra compact new light source, combining the lifetime

and reliability advantages of high power LED with the brightness of conventional lighting. K series can be

drive current rating from 350 mA to 700mA as your various needed.

GP K series LED that delivers elevated standards for light output, flux density and manufacture ability.

Offering better flux density, lumens per package and power handling capabilities.

Feature ■ Create more useable light and higher flux density

■ Available in White, Green, Blue, Red and Amber ■ Tightly pack the LEDs for color mixing applications ■ Engineer more robust applications ■ Lambertian radiation pattern ■ Low voltage DC operated, Cool beam, safe to the touch Instant lights ■ No UV ■ Superior ESD protection Typical application ■ Reading lights (car, bus, aircraft)

■ Portable (flashlight, bicycle) ■ LCD Backlights ■ General lighting ■ Indoor/Outdoor Commercial and Residential Architectural ■ Contourlights ■ Traffic signaling/Beacons/ Rail crossing and Wayside ■ Fiber optic alternative/ Decorative/Entertainment ■ Architecturallighting


Table of Contents

Product Nomenclature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Environmental Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Visual Appearance of GP K series LED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Flux Characteristics for GP K series LED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Optical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

JEDEC Moisture Sensitivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Mechanical Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Reflow Soldering Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Wavelength Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Typical Forward Current Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Typical Light Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . .14

Typical Radiation Patterns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Emitter Pocket Tape Packaging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Emitter Reel Packaging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Product Binning and Labeling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Luminous Flux Bins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Cool-White Bin Structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Neutral-White Bin Structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Warm-White Bin Structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Color Bins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Forward Voltage Bins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26


Product Nomenclature

GP K series LED is tested and binned at 350mA.

The part number designation is explained as follows:

GS - A B C D E

Where:

A — designates Power LED package (K for Lead Frame type)

B — designates package platform (2 for Lead Frame flat cup , 4 for Lead Frame cavity cup)

C — designates view angle (A for 140 degrees, B for 120 degrees, G for 160 degrees)

D — designates color variant (C for Cool-White, W for Warm-White, N for Neutral-White, B for Blue, G for Green,

R for Red, Y for Yellow)

E — designates chip classification

Environmental Compliance

GSEO LED BU is committed to providing environmentally friendly products to the solid-state lighting market. GP K

series LED is compliant to the European Union directives on the restriction of hazardous substances in electronic

equipment, namely the RoHS directive. GSEO LED BU will not intentionally add the following restricted materials to

the GP K series LED: lead, mercury, cadmium, hexavalent chromium, polybrominated biphenyls (PBB) or

polybrominated diphenyl ethers (PBDE).

Visual Appearance of GP K series LED

All lighted GP K series LED product will provide comparable Lambertian beam performance, suitable for use with

commercially available optical systems. Without power, LED die within different reels may appear visually different.


Luminous Flux characteristics

Flux Characteristics for GP K series LED — TJ = 25°C

Table 1. Luminous flux characteristics at IF=350 mA

Performance at Test Current

Color Part Number Minimum Luminous

Flux (lm)

Typical Luminous

Flux (lm)

Maximum Luminous

Flux (lm) Drive Current (mA)

GS-K2ACR

GS-K2ACE

98

95

107.5

105

--

--

350

350

Cool-White GS-K2ACT

GS-K3ACR

GS-K3ACE

GS-K3ACT

93

80

80

78.3

103

83.2

82.5

80.8

--

--

--

--

350

350

350

350

GS-K2ANR

GS-K2ANE

83.6

81.2

87.8

86.7

--

--

350

350

Neutral-White GS-K2ANT

GS-K3ANR

GS-K3ANE

GS-K3ANT

80.5

76.3

75.2

73.7

82.5

78.5

78

75.3

--

--

--

--

350

350

350

350

GS-K2AWR

GS-K2AWE

75

73.5

78.3

76.8

--

--

350

350

Warm-White GS-K2AWT

GS-K3AWR

GS-K3AWE

GS-K3AWT

72

70

70

68.7

75.2

73.7

72.8

71.6

--

--

--

--

350

350

350

350

GS-K2GGE 72.5 75.2 -- 350 Green

GS-K2GGF 73.7 78 -- 350

GS-K2GBE 16.1 20 -- 350

GS-K2GBF 15.8 18.5 -- 350 Blue

GS-K2GBS 15 25 -- 350

GS-K2ARE 31.7 43.3 -- 350 Red

GS-K2ARH 33 45 -- 350

GS-K2AYE 33.8 40.9 -- 350 Amber

GS-K2AYH 35.5 43.1 -- 350


Flux Characteristics for GP K series LED — TJ = 25°C

Table 2. Luminous flux characteristics at IF=700 mA

Performance at Test Current

Color Part Number Minimum Luminous

Flux (lm)

Typical Luminous

Flux (lm)

Maximum Luminous

Flux (lm) Drive Current (mA)

GS-K2ACR

GS-K2ACE

166.6

161.5

182.8

178.5

--

--

700

700

Cool-White GS-K2ACT

GS-K3ACR

GS-K3ACE

GS-K3ACT

158

136

135.3

133

175

141.4

140.3

137.4

--

--

--

--

700

700

700

700

GS-K2ANR

GS-K2ANE

142.1

138

149.3

147.4

--

--

700

700

Neutral-White GS-K2ANT

GS-K3ANR

GS-K3ANE

GS-K3ANT

136.9

129.7

127.8

125.3

140.3

133.5

132.6

128

--

--

--

--

700

700

700

700

GS-K2AWR

GS-K2AWE

127.5

125

133.1

130.5

--

--

700

700

Warm-White GS-K2AWT

GS-K3AWR

GS-K3AWE

GS-K3AWT

122.5

119

119

116.8

127.8

125.3

123.8

121.7

--

--

--

--

700

700

700

700

GS-K2GGE 123.3 127.8 -- 700 Green

GS-K2GGF 125.3 132.6 -- 700

GS-K2GBE 27.4 34 -- 700

GS-K2GBF 26.9 32.8 -- 700 Blue

GS-K2GBS 25.5 35.5 -- 700

GS-K2ARE 55.8 76.3 -- 700 Red

GS-K2ARH 57.7 79.6 -- 700

GS-K2AYE 60.1 67.2 -- 700 Amber

GS-K2AYH 62.5 70.7 -- 700

Notes for Table 1,2: 1. Minimum luminous flux or radiometric power performance guaranteed within published operating

conditions. GSEO LED BU maintains a tolerance of ± 10% on flux measurements. 2. Typical luminous flux performance when device is operated within published operating conditions. 3. GP K series LED products with even higher luminous flux and radiometric power levels will become

available in the future. 4. Typical CRI (Color Rendering Index) for K3 are 90. 5. All radiation patterns are Lambertian.


Optical Characteristics

GP K series LED at Test Current[1] , TJ = 25°C

Table 3. Optical characteristics at IF=350 mA and TJ= 25°C

Notes for Table 3:

1. Test current is 350 mA for all GS-K2XXX products.

2. Dominant wavelength is derived from the CIE 1931 Chromaticity diagram and represents the perceived

color. GSEO LED BU maintains a tolerance of ± 1 nm for dominant wavelength measurements.

3. CCT ±5% tester tolerance.

4. Spectral width at ½ of the peak intensity.

5. Viewing angle is the off axis angle from lamp centerline where the luminous intensity is ½ of the peak value.

6. All red and amber products built with Aluminum Indium Gallium Phosphide (AlInGaP).

7. All white, warm white, green and blue products built with Indium Gallium Nitride (InGaN).

Dominant Wavelength [2]λD

or Color Temperature [3]

CCT

Radiation

Pattern Color

Min. Typ. Max.

Typical

Spectral

Half-width [4]

(nm)

∆λ1/2

Typical

Temperature

Coefficient of

Dominant

Wavelength

(nm/℃)

∆λD/ ∆TJ

Typical

Viewing

Angle [5]

(degrees)

2θ1/2

Cool-White 4500K 6500K 10,000 K N/A N/A 140

Neutral-White 3500K 4100 K 4500 K N/A N/A 140

Warm-White 2670K 3100 K 3500 K N/A N/A 140

Green 520nm 530 nm 550 nm 30 0.05 160

Blue 460 nm 470 nm 490 nm 21 0.05 160

Red 620.5 nm 627 nm 645 nm 20 0.05 140

Lambertian

Amber 584.5 nm 590 nm 597 nm 20 0.10 140


Electrical Characteristics

Electrical Characteristics at 350mA for GP K series LED,

Part Numbers GS-K2XXX

TJ = 25°C

Table 4. Electrical characteristics at IF=350 mA and TJ= 25°C

Notes for Table 4:

1. GSEO LED BU maintains a tolerance of ±0.06 V on forward voltage measurements.

2. Dynamic resistance is the inverse of the slope in linear forward voltage model for LEDs. See Figures 5 and 6.

Color temperature characteristics Table 5. CRI characteristics at at IF=350 mA and TJ= 25°C

Color

Forward Voltage Vf[1]

(V)

Min. Typ. Max.

Dynamic

Resistance

RD(Ω) f[2]

Typical Thermal Resistance

Junction to case

(oC/W)

RθJ-C

Cool-White 2.8 -- 4.1 1.2 12

Neutral-White 2.8 -- 4.1 1.2 12

Warm-White 2.8 -- 4.1 1.2 12

Green 2.8 -- 4.1 1.2 12

Blue 2.8 -- 4.1 1.2 12

Red 2.12 -- 3.3 2.5 15

Amber 2.12 -- 3.3 2.5 15

Radiation

Pattern Part Number Color

CRI

Typ.

GS-K2ACR

GS-K2ACE

GS-K2ACT

Cool-White 80

GS-K2ANR

GS-K2ANE

GS-K2ANT

Neutral-White 85 Lambertian

GS-K2AWR

GS-K2AWE

GS-K2AWT

Warm-White 87

GS-K3ACR

GS-K3ACE

GS-K3ACT

Cool-White 90

GS-K3ANR

GS-K3ANE

GS-K3ANT

Neutral-White 90 Lambertian

GS-K3AWR

GS-K3AWE

GS-K3AWT

Warm-White 90


Absolute Maximum Ratings Table 6. GP K series absolute maximum rating

Parameter Cool-White/Neutral-White/ Warm-White/Green/Blue Red/Amber

DC Forward Current (mA) [1] 700

Peak Pulesd Forward Current (mA) 700

Average Forward Current (mA) 350

Reverse Voltage 5V

ESD Sensitivity [2] <8000V Human Body Model (HBM)

LED Junction Temperature 130°C 125°C

Storage Temperature -40°C ~ 120°C

Operation Temperature -30°C ~ 110°C

Notes for Table 6:

1. Proper current derating must be observed to maintain junction temperature below the maximum. 2. GP K series LEDs are not designed to be driven in reverse bias.

JEDEC Moisture Sensitivity Table 7. JEDEC characteristics at IF=350 mA and TJ= 25°C

Level Floor Life

Time Conditions

Soak Requirements

Standard

Time(hours) Conditions

1 Unlimited ≦30℃/85％RH 168 +5/0 85℃ / 85％RH

Table 7.1 Moisture Sensitivity Levels

Level Floor Life

Time Conditions

Soak Requirements

Standard Accelerated Environment

Time(hours) Conditions Time(hours) Conditions

1 Unlimited ≦30℃/85％RH

2 1 year ≦30℃/60％RH

2a 4 weeks ≦30℃/60％RH

3 168 hours ≦30℃/60％RH

4 72 hours ≦30℃/60％RH

5 48 hours ≦30℃/60％RH

5a 24 hours ≦30℃/60％RH

6 TOL ≦30℃/60％RH

(Time on table)

168] +5/0

168] +5/0

696] [1] +5/0

192] [1] +5/0

96] [1] +5/0

72] [1] +5/0

48] [1] +5/0

TOL

85℃ / 85％RH

85℃ / 60％RH

30℃ / 60％RH

30℃ / 60％RH

30℃ / 60％RH

30℃ / 60％RH

30℃ / 60％RH

30℃ / 60％RH

120 +1/0

40 +1/0

20 +1/0

15 +1/0

10 +1/0

60℃ / 60％RH

60℃ / 60％RH

60℃ / 60％RH

60℃ / 60％RH

60℃ / 60％RH

Notes for Table 7.1:

1. The standard soak time includes a default value of 24hours for semiconductor manufacturer’s exposure

time(MET) between bake and bag, and includes the maximum time allowed out of the bag at the

distributor’s facility

2. Supplier may extend the soak times at their own risk.


Mechanical Dimensions

Lambertian

Figure 1. GP K series outline

Figure 2. GP K series with star outline

Notes for Figure 1,2:

1. Do not handle the device by the lens-care must be taken to avoid damage to the lens or the interior

of the device that can be damaged by excessive force to the lens.

2. All dimensions are in millimeters.


Reflow Soldering Characteristics

Table 8. GP K series Reflow profile

Profile Feature Lead Free Assembly

Average RampUP Rate (Tsmaxto Tp) 3°C / second max

Preheat Temperature Min(Tsmin) 150°C

Preheat Temperature Max (Tsmax) 200°C

Preheat Time (tsminto tsmax) 60-180 seconds

Time Maintained Above Temperature (TL) 217°C

Time Maintained Above Time (tL) 60-150 seconds

Peak / Classification Temperature (TP) 260°C

Time Within 5°C of Actual Peak Temperature (tP) 20-40 seconds

Ramp-Down Rate 6°C / second max

Time 25°C to Peak Temperature 8 minutes max

Notes for Table 8:

1. All temperatures refer to the application Printed Circuit Board (PCB), measured on the surface adjacent to the package

body.


Wavelength Characteristics

Royal Blue, Blue, Cyan, Green, Red-Orange, Red and Amber

at Test Current 350 mA, TJ= 25°C

0.0

0.2

0.4

0.6

0.8

1.0

400 450 500 550 600 650 700

Wavelength (nm)

Relative Specrtal Power Distribution

BLUE

GREEN

AMBER

RED

Figure 3. Relative intensity vs. wavelength

Cool-White at Test Current 350 mA, TJ= 25°C

Figure 4a. Cool-White color spectrum of typical CCT part, integrated measurement.

0

20

40

60

80

100

350 400 450 500 550 600 650 700 750 800

Wavelength (nm)

Relative Spectral Power

Distribution (%

)


Neutral-White at Test Current 350 mA, TJ= 25°C

400 450 500 550 600 650 700 750 800

Wavelength (nm)

Spectral Power Distribution

Figure 4b. Neutral-White color spectrum of typical CCT part, integrated measurement.

Warm-White at Test Current 350 mA, TJ= 25°C

400 450 500 550 600 650 700 750 800

Wavelength (nm)

Spectral Power Distribution

Figure 4c. Warm-White color spectrum of typical CCT part, integrated measurement.


Typical Forward Current Characteristics

Cool-White, Neutral-White, Warm-White, Green and Blue, at Test Current 350 mA and TJ= 25°C

0

50

100

150

200

250

300

350

400

0 0.5 1 1.5 2 2.5 3 3.5 4 4.5

VF - Forward Voltage(volts)

IF - Average Forw

ard Current(mA)

Figure 5. Forward current vs. forward voltage for all White, Green and Blue.

Red and Amber, at Test Current 350 mA and TJ= 25°C

0

50

100

150

200

250

300

350

400

0 0.5 1 1.5 2 2.5 3 3.5 4

VF - Forward Voltage(volts)

IF - Average Forw

ard Current(mA)

Figure 6. Forward current vs. forward voltage for Red and Amber.


Typical Light Output

Relative light output for all White, Green and Blue, at Test Current 350 mA and TJ= 25°C

Figure 7. Relative light output for all White, Green and Blue, test current 350mA.

Relative light output for Red and Amber, at Test Current 350 mA and TJ= 25°C

Figure 8. Light output for Red and Amber, test current 350mA.

0

20

40

60

80

100

120

140

160

180

200

-20 0 20 40 60 80 100 120

Junction Temperature TJ ( ℃)

Relative Light Output (%

)

Red

Amber

50

60

70

80

90

100

110

120

130

140

150

-20 0 20 40 60 80 100 120

Junction Temperature TJ ( ℃)

Relative Light Output (%

)

Green Photometric

Blue Photometric

White Photometric


Typical Radiation Patterns

Typical Representative Spatial Radiation Pattern

for all-White Lambertian

0%

10%

20%

30%

40%

50%

60%

70%

80%

90%

100%

-90 -80 -70 -60 -50 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90

Angular Displacement deg

Relative lntensity %

Figure 9. Typical representative spatial radiation pattern for all White lambertian.

Typical Polar Radiation Pattern for White Lambertian

Figure 10. Typical polar radiation pattern for all White lambertian


Typical Representative Spatial Radiation Pattern for Green and Blue Lambertian

0

10

20

30

40

50

60

70

80

90

100

-90 -80 -70 -60 -50 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90


Relative Intensity %

Figure 11. Typical representative spatial radiation pattern for Green and Blue lambertian.

Typical Polar Radiation Pattern for Green and Blue Lambertian

Figure 12. Typical polar radiation pattern for Green and Blue lambertian


Typical Representative Spatial Radiation Pattern

for Red and Amber Lambertian

0%

10%

20%

30%

40%

50%

60%

70%

80%

90%

100%

-90 -80 -70 -60 -50 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90


Relative lntensity %

Figure 13. Typical representative spatial radiation pattern for Red and Amber lambertian.

Typical Polar Radiation Pattern for Red and Amber Lambertian

Figure 14. Typical polar radiation pattern for Red and Amber lambertian


Emitter Pocket Tape Packaging

Unit: mm

Emitter Reel Packaging Unit: mm


Product Binning and Labeling

Purpose of Product Binning In the manufacturing of semiconductor products, there is a variation of performance around the average values given in the technical data sheets. For this reason, GSEO LED BU bins the LED components for luminous flux, color and forward voltage (VF).

Decoding Product Bin Labeling GP K series LED are labeled using four digit alphanumeric code (CAT code) depicting the bin values for LED packaged on a single reel. All LEDs packaged within a reel are of the same 3 variable bin combination. Using these codes, it is possible to determine optimum mixing and matching of products for consistency in a given application.

Format of Labeling for Emitters Reels of Green, Blue, Red and Amber LEDs are labeled with a four digit alphanumeric CAT

code following the format below.

ABCD

A = Flux bin (H, J, K, L etc.)

B = Color bin (1, 2, 3, etc.)

C = Wavelength bin (1, 2, 3, etc.)

D = VFbin (D, E, F, G etc.)

Reels of Cool-White, Neutral-White and Warm-White Emitters are labeled with a four digit alphanumeric CAT code following the format below.

ABCD

A = Flux bin (J, H, J, K etc.)

B and C = Color bin (W0, U0, V0 etc.)

C = VFbin (D, E, F, G etc.)


Luminous Flux Bins

Table 9 lists the standard photometric luminous flux bins for GP K series LED (tested and binned at 350mA).

Although several bins are outlined, product availability in a particular bin varies by production run and by product

performance. Not all bins are available in all colors.

Table 9.

Flux Bins - All Colors

Minimum Photometric Flux Maximum Photometric Flux

Bin Code (lm) (lm)

A 8 12

B 12 16

C 16 20

D 20 24

E 24 30

F 28 32

G 32 36

H 36 40

I 40 45

J 45 50

K 50 60

L 60 70

M 70 80

N 80 90

P 90 100

Q 100 120

R 120 140

S 140 160

T 160 180

U 180 200

V 200 220

W 220 240

X 240 260

y 260 280

Z 280 300


Cool-White Bin Structure

WQWQYO

YA

XM

XN

X0

XP

WM

WN

W0

WP

VM

VN

V0

VP

UM

UN

U0

UP

0.25

0.27

0.29

0.31

0.33

0.35

0.37

0.39

0.41

0.25 0.27 0.29 0.31 0.33 0.35 0.37 0.39x

y

4500K

5000K

5630K

6300K

7000K

blackbody locus

10000K

Figure 15. Cool-White bin structure


Cool-White Bin Coordinates

Cool-White GP K series LED are tested and binned by x,y coordinates.

19 Color Bins, CCT Range 10,000K to 4,500K

Table 10.

Cool-White Bin Coordinates

Typical CCT Typical CCT

Bin Code X Y (K) Bin Code X Y (K)

0.274238 0.300667 0.318606 0.310201

Y0 0.303051 0.332708 8000 WQ 0.329393 0.320211 6000

0.307553 0.310778 0.329544 0.310495

0.282968 0.283772 0.319597 0.301303

0.282968 0.283772 0.328636 0.368952

YA 0.307553 0.310778 8000 VM 0.348147 0.385629 5300

0.311163 0.293192 0.346904 0.371742

0.289922 0.270316 0.328823 0.356917

0.301093 0.342244 0.328823 0.356917

XM 0.313617 0.354992 6700 VN 0.346904 0.371742 5300

0.314792 0.344438 ` 0.345781 0.359190

0.303051 0.332708 0.329006 0.345092

0.303051 0.332708 0.329006 0.345092

XN 0.314792 0.344438 6700 VO 0.345781 0.359190 5300

0.316042 0.333222 0.344443 0.344232

0.305170 0.322386 0.329220 0.331331

0.305170 0.322386 0.329220 0.331331

XO 0.316042 0.333222 6700 VP 0.343352 0.344232 5300

0.317466 0.320438 0.329393 0.332034

0.307553 0.310778 0.348147 0.320211

0.307553 0.310778 0.348147 0.385629

XP 0.317466 0.320438 6700 UM 0.367294 0.400290 4750

0.319597 0.301303 0.364212 0.382878

0.311163 0.293192 0.346904 0.371742

0.313617 0.354992 0.346904 0.371742

WM 0.328636 0.368952 6000 UN 0.364212 0.382878 4750

0.328823 0.356917 0.362219 0.371616

0.314792 0.344438 0.345781 0.359190

0.314792 0.344438 0.345781 0.359190

WN 0.328823 0.356917 6000 UO 0.362219 0.371616 4750

0.329006 0.345092 0.359401 0.355699

0.316042 0.333222 0.344443 0.344232

0.316042 0.333222 0.344443 0.344232

WO 0.329006 0.345092 6000 UP 0.359401 0.355699 4750

0.329220 0.331331 0.357079 0.342581

0.317466 0.320438 0.343352 0.332034

0.317466 0.320438

WP 0.329220 0.331331 6000

0.329393 0.320211

0.318606 0.310201

.

Note for Table 10:

1. GP K series LED maintains a tester tolerance of ± 0.005 on x, y color coordinates.


Neutral-White Bin Structure

TM

TN

T0

TP

SM

SN

S0

SP

RM

RN

R0

RP

0.32

0.34

0.36

0.38

0.4

0.42

0.44

0.33 0.35 0.37 0.39 0.41 0.43x

y

3500K

3800K

blackbody locus

4100K

4500K

Figure 16: Neutral-White Bin Structure

Neutral-White GP K series LED are tested and binned by x,y coordinates. 12 Color Bins, CCT Range 4,500K to 3,500K

Table 11.

Neutral-White Bin Coordinates



0.367294 0.400290 0.378624 0.382458

TM 0.385953 0.412995 4300 SO 0.392368 0.399093 3950

0.381106 0.393747 0.387071 0.373899

0.364212 0.382878 0.374075 0.365822

0.364212 0.382878 0.374075 0.365822

TN 0.381106 0.393747 4300 SP 0.387071 0.373899 3950

0.378264 0.382458 0.382598 0.359515

0.362219 0.371616 0.370582 0.351953

0.362219 0.371616 0.402270 0.422776

TO 0.378264 0.382458 4300 RM 0.420940 0.432618 3650

0.374075 0.365822 ` 0.414776 0.416097

0.359401 0.355699 0.396279 0.403508

0.359401 0.355699 0.396279 0.403508

TP 0.374075 0.365822 4300 RN 0.414776 0.416097 3650

0.370582 0.351953 0.408593 0.399525

0.357079 0.342581 0.392368 0.390932

0.385953 0.412995 0.392368 0.390932

SM 0.402270 0.422776 3950 RO 0.408593 0.399525 3650

0.396279 0.403508 0.402113 0.382156

0.381106 0.393747 0.387071 0.373899

0.381106 0.393747 0.387071 0.373899

SN 0.396279 0.403508 3950 RP 0.402113 0.382156 3650

0.392368 0.390932 0.396564 0.367284

0.378264 0.382458 0.382598 0.359515

Note for Table 11:

1. GSEO LED BU maintains a tester tolerance of ± 0.005 on x, y color coordinates.


Warm-White Bin structure

QM

QN

Q0

QP

PM

PN

P0

PP

NM

NN

N0

NP

MM

MN

M0

MP

0.35

0.37

0.39

0.41

0.43

0.45

0.47

0.38 0.4 0.42 0.44 0.46 0.48 0.5x

y

blackbody locus

2670K2850K3050K

3500K3250K

Figure 17: Warm-White Bin Structure.

Warm-White GP K series LED are tested and binned by x,y coordinates. 16 Color Bins, CCT Range 3,500K to 2,670K

Table 12.

Warm-White Bin Coordinates



0.420940 0.432618 0.453820 0.445980

QM 0.438458 0.440399 3375 NM 0.470507 0.450832 2950

0.431186 0.423386 0.461404 0.433334

0.414776 0.416097 0.445639 0.428680

0.414776 0.416097 0.445639 0.428680

QN 0.431186 0.423386 3375 NN 0.461404 0.43334 2950

0.423956 0.406472 0.452512 0.416241

0.408593 0.399525 0.437578 0.411632

0.408593 0.399525 0.437578 0.411632

QO 0.423956 0.406472 3375 NO 0.452512 0.416241 2950

0.416487 0.389001 ` 0.443600 0.399111

0.402113 0.382156 0.429373 0.394281

0.402113 0.382156 0.429373 0.394281

QP 0.416487 0.389001 3375 NP 0.443600 0.399111 2950

0.409996 0.373814 0.435591 0.383714

0.396564 0.367284 0.422124 0.378952

0.438458 0.440399 0.470507 0.450832

PM 0.453820 0.445980 3150 MM 0.486648 0.454191 2760

0.445639 0.428680 0.476733 0.436634

0.431186 0.423386 0.461404 0.433334

0.431186 0.423386 0.461404 0.433334

PN 0.445639 0.428680 3150 MN 0.476733 0.436634 2760

0.437578 0.411632 0.467132 0.419632

0.423956 0.406472 0.452512 0.416241

0.423956 0.406472 0.452512 0.416241

PO 0.437578 0.411632 3150 MO 0.467132 0.419632 2760

0.429373 0.394281 0.457663 0.402866

0.416487 0.389001 0.443600 0.399111

0.416487 0.389001 0.443600 0.399111

PP 0.429373 0.394281 3150 MP 0.457663 0.402866 2760

0.422124 0.378952 0.448994 0.387515

0.409996 0.373814 0.435591 0.383714


Color Bins

All GP K series LED are tested and binned for dominant wavelength.

Dominant Wavelength Bin Structure for Green Table13.

Bin Code

Minimum Dominant Wavelength

(nm)

Maximum Dominant Wavelength

(nm)

31 520 525

32 525 530

33 530 535

34 535 540

35 540 545

36 545 550

Dominant Wavelength Bin Structure for Blue Table14.

Bin Code


(nm)


(nm)

41 450 455

42 455 460

43 470 475

44 475 480

45 480 485

46 485 490

Dominant Wavelength Bin Structure for Red

Dominant Wavelength Bin Structure for Amber Table16.

Bin Code


(nm)


(nm)

51 584.5 587.0

52 587.0 589.5

53 589.5 592.0

54 592.0 594.5

55 594.5 597.0

Table15.

Bin Code


(nm)


(nm)

11 620.5 631

12 631 645


Forward Voltage Bins

Table 15 lists minimum and maximum VF bin values per emitter. Although several bins are outlined, product availability in

a particular bin varies by production run and by product performance.

Table17.

VF Bins

Bin Code

Minimum Forward Voltage

(V)

Maximum Forward Voltage

(V)

A 2.07 2.31

B 2.31 2.55

C 2.55 3.79

D 3.79 3.03

E 3.03 3.27

F 3.27 3.51

G 3.51 3.75

H 3.75 3.99

2 2 2.5

3 2.5 3

4 3 3.6

5 3.6 4.2

6 4.2 5

Documents

High Power LED K Series LED - GSEO · GP K series LED Datasheet ... High Power LED GP ® K Series LED ... 1 Unlimited ≦30 ℃/85 ％RH 168 +5/0 85 ℃ / 85 ％RH Table 7.1 Moisture