41

hd hikvision ds 2cc51d3s vpir

Embed Size (px)

DESCRIPTION

κάμερα κλειστού κυκλώματος HD

Citation preview

Page 2: hd hikvision ds 2cc51d3s vpir

HD-SDI Camera·User Manual

2

Thank you for purchasing our product. If there are any questions, or requests,

please do not hesitate to contact the dealer.

This manual applies to DS-2CC11D3S-IR, DS-2CC51D3S-VPIR.

This manual may contain several technical incorrect places or printing errors, and

the content is subject to change without notice. The updates will be added to the

new version of this manual. We will readily improve or update the products or

procedures described in the manual.

DISCLAIMER STATEMENT

“Underwriters Laboratories Inc. (“UL”) has not tested the performance or

reliability of the security or signaling aspects of this product. UL has only tested

for fire, shock or casualty hazards as outlined in UL s Standard(s) for Safety,

UL60950-1. UL Certification does not cover the performance or reliability of the

security or signaling aspects of this product. UL MAKES NO REPRESENTATIONS,

WARRANTIES OR CERTIFICATIONS WHATSOEVER REGARDING THE

PERFORMANCE OR RELIABILITY OF ANY SECURITY OR SIGNALING RELATED

FUNCTIONS OF THIS PRODUCT.

0100001030609

www.sat-alarm.gr/

Page 3: hd hikvision ds 2cc51d3s vpir

HD-SDI Camera·User Manual

3

Regulatory Information

FCC Information

FCC compliance: This equipment has been tested and found to comply with the

limits for a digital device, pursuant to part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference when

the equipment is operated in a commercial environment. This equipment

generates, uses, and can radiate radio frequency energy and, if not installed and

used in accordance with the instruction manual, may cause harmful interference

to radio communications. Operation of this equipment in a residential area is

likely to cause harmful interference in which case the user will be required to

correct the interference at his own expense.

FCC Conditions

This device complies with part 15 of the FCC Rules. Operation is subject to the

following two conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including interference that

may cause undesired operation.

EU Conformity Statement

This product and - if applicable - the supplied accessories too

are marked with "CE" and comply therefore with the

applicable harmonized European standards listed under the

Low Voltage Directive 2006/95/EC, the EMC Directive 2004/108/EC, the RoHS

Directive 2011/65/EU.

2012/19/EU (WEEE directive): Products marked with this

symbol cannot be disposed of as unsorted municipal waste in

the European Union. For proper recycling, return this product

to your local supplier upon the purchase of equivalent new

Page 4: hd hikvision ds 2cc51d3s vpir

HD-SDI Camera·User Manual

4

equipment, or dispose of it at designated collection points. For more information

see: www.recyclethis.info.

2006/66/EC (battery directive): This product contains a

battery that cannot be disposed of as unsorted municipal

waste in the European Union. See the product

documentation for specific battery information. The battery

is marked with this symbol, which may include lettering to

indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling, return

the battery to your supplier or to a designated collection point. For more

information see: www.recyclethis.info.

Safety Instruction

These instructions are intended to ensure that user can use the product correctly

to avoid danger or property loss.

The precaution measure is divided into “Warnings” and “Cautions”

Warnings: Serious injury or death may occur if any of the warnings are

neglected.

Cautions: Injury or equipment damage may occur if any of the cautions are

neglected.

Warnings Follow these

safeguards to prevent serious

injury or death.

Cautions Follow these precautions

to prevent potential injury or

material damage.

Page 5: hd hikvision ds 2cc51d3s vpir

HD-SDI Camera·User Manual

5

Warnings

In the use of the product, you must be in strict compliance with the electrical

safety regulations of the nation and region.

Please refer to technical specifications for detailed information.

Input voltage should meet both the SELV (Safety Extra Low Voltage) and the

Limited Power Source with AC 24V or DC 12V according to the IEC60950-1

standard. Please refer to technical specifications for detailed information.

Do not connect several devices to one power adapter as adapter overload may

cause over-heating or a fire hazard.

Please make sure that the plug is firmly connected to the power socket.

When the product is mounted on wall or ceiling, the device shall be firmly

fixed.

If smoke, odor or noise rise from the device, turn off the power at once and

unplug the power cable, and then please contact the service center.

If the product does not work properly, please contact your dealer or the

nearest service center. Never attempt to disassemble the camera yourself.

(We shall not assume any responsibility for problems caused by unauthorized

repair or maintenance.)

Cautions

Make sure the power supply voltage is correct before using the camera.

Do not drop the camera or subject it to physical shock.

http://www.sat-alarm.gr/

Page 6: hd hikvision ds 2cc51d3s vpir

HD-SDI Camera·User Manual

6

Do not touch senor modules with fingers. If cleaning is necessary, use clean

cloth with a bit of ethanol and wipe it gently. If the camera will not be used for

an extended period, please replace the lens cap to protect the sensor from

dirt.

Do not aim the camera at the sun or extra bright places. Blooming or smearing

may occur otherwise (which is not a malfunction), and affect the endurance of

sensor at the same time.

The sensor may be burned out by a laser beam, so when any laser equipment

is in using, make sure that the surface of sensor will not be exposed to the

laser beam.

Do not place the camera in extremely hot, cold (the operating temperature

shall be-10℃~+60℃), dusty or damp locations, and do not expose it to high

electromagnetic radiation.

To avoid heat accumulation, good ventilation is required for operating

environment.

Keep the camera away from liquid while in use.

While in delivery, the camera shall be packed in its original packing, or packing

of the same texture.

Improper use or replacement of the battery may result in hazard of explosion.

Replace with the same or equivalent type only. Dispose of used batteries

according to the instructions provided by the battery manufacturer.

http://www.sat-alarm.gr/

Page 7: hd hikvision ds 2cc51d3s vpir

HD-SDI Camera·User Manual

7

Table of Contents 1 Introduction ...................................................................................................... 9

1.1 Product Features .............................................................................. 9

1.2 Overview ........................................................................................ 10

2 Installation ...................................................................................................... 12

2.1 Installation of HD-SDI Bullet Camera............................................... 12

2.2 Installation of HD-SDI Dome Camera .............................................. 14

3 Menu Description ........................................................................................... 18

3.1 LENS ............................................................................................... 18

3.2 EXPOSURE ...................................................................................... 19

3.2.1 Shutter ................................................................................ 19

3.2.2 AGC ..................................................................................... 20

3.2.3 SENS-UP............................................................................... 20

3.2.4 Brightness ............................................................................ 20

3.2.5 ACCE(Adaptive Contrast & Color Enhancement) .................. 20

3.2.6 Defog ................................................................................... 21

3.2.7 Backlight .............................................................................. 21

3.2.8 White Balance (WB) ............................................................. 24

3.3 Day & Night .................................................................................... 25

3.4 NR .................................................................................................. 26

3.5 SPECIAL .......................................................................................... 27

3.5.1 Camera Title ........................................................................ 28

3.5.2 D-effect................................................................................ 29

3.5.3 Motion ................................................................................ 30

3.5.4 Privacy ................................................................................. 32

3.5.5 Language ............................................................................. 33

3.5.6 Defect .................................................................................. 34

3.5.7 RS485 .................................................................................. 35

Page 8: hd hikvision ds 2cc51d3s vpir

HD-SDI Camera·User Manual

8

3.5.8 Version ................................................................................ 35

3.6 ADJUST ........................................................................................... 36

3.6.1 Sharpness ............................................................................ 36

3.6.2 Monitor ............................................................................... 37

3.6.3 OSD ..................................................................................... 39

3.6.4 LSC ....................................................................................... 39

3.6.5 NTSC/PAL ............................................................................. 39

3.7 RESET ............................................................................................. 40

3.8 EXIT ................................................................................................ 40

http://www.sat-alarm.gr/

Page 9: hd hikvision ds 2cc51d3s vpir

HD-SDI Camera·User Manual

9

1 Introduction

1.1 Product Features

This series of camera adopts high-sensitive sensor and advanced circuit board

design technology. It features high resolution, low distortion, and low noise

features, etc., which make it extremely suitable for surveillance system and

image process system.

The main features of HD-SDI cameras are as follows:

2 Megapixel high-performance CMOS sensor

Clear and detailed image of up to 1080P resolution

Low illumination: 0.01Lux @ (F1.2,AGC ON), 0 Lux with IR

IR cut filter auto switch

Auto white balance, auto gain control, and backlight compensation for

different surveillance environment

Support Digital Wide Dynamic Range (D-WDR) for backlighting surveillance

OSD menu, parameters are configurable

Advanced 3-axis design

Ingress protection level reaches IP66

Page 10: hd hikvision ds 2cc51d3s vpir

HD-SDI Camera·User Manual

10

1.2 Overview

Overview of HD-SDI Bullet Camera Figure 1-1

Table 1-1 Description

No. Description No. Description

1 Mounting Base 6 OK Button

2 Adjustable Nut 7 SDI Cable

3 Sun Shield 8 Power Cable

4 Lens 9 Auxiliary Video Output

5 IR LED 10 RS485 Cable

1

2

3

4

5

69

10

8

7

OK

Page 11: hd hikvision ds 2cc51d3s vpir

HD-SDI Camera·User Manual

11

Overview of HD-SDI Dome Camera Figure 1-2

Table 1-2 Description

No. Description No. Description

1 Mounting Base 6 OK Button

2 Black Liner 7 SDI Cable

3 Lower Dome 8 Power Cable

4 IR LED 9 Auxiliary Video Output

5 Lens 10 RS485 Cable

1

2

3

4

56

78

9

10

K

Page 12: hd hikvision ds 2cc51d3s vpir

HD-SDI Camera·User Manual

12

2 Installation

Before you start:

Please make sure that the device in the package is in good condition and all

the assembly parts are included.

Make sure that all the related equipment is power-off during the installation.

Check the specification of the products for the installation environment.

Check whether the power supply is matched with your AC outlet to avoid

damage.

If the product does not function properly, please contact your dealer or the

nearest service center. Do not disassemble the camera for repair or

maintenance by yourself.

Please make sure the wall is strong enough to withstand three times the

weight of the camera.

2.1 Installation of HD-SDI Bullet Camera

Steps:

1. Drill the screw holes in the wall according to the drill template.

Page 13: hd hikvision ds 2cc51d3s vpir

HD-SDI Camera·User Manual

13

Drill Template Figure 2-1

2. Route the corresponding cables.

3. Fix the camera to the wall with the supplied P A4 screws.

Secure the Camera to the Wall Figure 2-2

φ68

55φφ4

Cutting line

Screw Hole

Template

Page 14: hd hikvision ds 2cc51d3s vpir

HD-SDI Camera·User Manual

14

4. Connect the video output cable to the monitor. Connect the power cable to

the power supply.

5. Adjust the Lens.

1). Loosen the adjustable nut.

2). Adjust the camera from pan direction which is 0~360°adjustable.

3). Adjust the camera from tilt direction which is 0~90°adjustable.

4). Rotate 0~360° to adjust the lens to the surveillance angle.

5). Tighten the adjustable nut to complete the installation.

3-axis Adjustment Figure 2-3

2.2 Installation of HD-SDI Dome Camera

Steps:

1. Drill the screw holes on the ceiling according to the drill template.

AdjustableNut

T Direction

R Direction

P Direction

Page 15: hd hikvision ds 2cc51d3s vpir

HD-SDI Camera·User Manual

15

Drill Template Figure 2-4

2. Loosen the set screws with a hex key (supplied) to remove the lower dome.

Remove the Lower Dome Figure 2-5

Hole

Hole Hole

Ceiling Mounting

Page 16: hd hikvision ds 2cc51d3s vpir

HD-SDI Camera·User Manual

16

3. Fix the mounting base on the ceiling with screws.

Fix the Mounting Base Figure 2-6

Note: If required, you can route cables through the side opening on the side

of the mounting base.

Side Opening Figure 2-7

4. Loosen the tilt lock screws, adjust the tilting position in a range of 65

degrees, and tighten the tilt lock screws.

Side Opening

Page 17: hd hikvision ds 2cc51d3s vpir

HD-SDI Camera·User Manual

17

5. Rotate the black liner to adjust the panning position in a range of 180

degrees until you get the desired surveillance angle.

Angle Adjustment Figure 2-8

Note: As the lens has already been factory adjusted to the best imaging effect,

you just need to adjust the panning position and tilting position to get the

desired surveillance angle.

6. Reinstall the lower dome and tighten the screws.

Lower Dome Reinstallation Figure 2-9

Tilt Lock Screw

Black Liner

PAN

TILT

Page 18: hd hikvision ds 2cc51d3s vpir

HD-SDI Camera·User Manual

18

3 Menu Description

Main Menu Overview Figure 3-1

Notes:

The OK button on the cable is used to control the menu.

Press the OK button up/down to select the menu item.

Press the OK button left/right to adjust the value.

OK button is also used to confirm a selection.

3.1 LENS

The camera is equipped with a fixed lens, which is not configurable.

Page 19: hd hikvision ds 2cc51d3s vpir

HD-SDI Camera·User Manual

19

3.2 EXPOSURE

EXPOSURE

SHUTTER AUTOAGC OFFSENS-UP ---BRIGHTNESS ---|------ 40ACCE OFFDEFOG OFFBACKLIGHT OFFRETURN RET

Exposure Figure 3-2

Exposure describes the brightness-related parameters. You can adjust the image

brightness by the SHUTTER, AGC, SENS-UP, BRIGHTNESS, ACCE, BACKLIGHT, etc.

in different light conditions.

3.2.1 Shutter

Shutter denotes the speed of the shutter.

AUTO,1/25, 1/50, FLK, 1/250, 1/500, 1/1k, 1/2k, 1/5k, 1/10k, 1/50k, x2, x4, x6, x8,

x10, x15, x20, x30, and x60 are selectable.

Note:

If you select shutter as AUTO or 1/25, the SENS-UP is adjustable (OFF/AUTO), and

the SENS-UP is disabled if any other shutter speed is selected.

Page 20: hd hikvision ds 2cc51d3s vpir

HD-SDI Camera·User Manual

20

3.2.2 AGC

It s a form of amplification where the camera will automatically boost the image

received in much lower light conditions than standard in order to optimize the

clarity of image in poor light scene. OFF, LOW, MIDDLE, and HIGH are selectable

for the AGC value.

Note:

The noise will be amplified if the AGC is on.

3.2.3 SENS-UP

SENS-UP increases the exposure on a signal frame, which makes a camera more

sensitive to light so it can produce images even in low lux conditions. You can set

the SENS-UP to OFF or AUTO according to different light conditions.

OFF: SENS-UP function is disabled.

AUTO: The SENS-UP function will atomically adjust itself to x2, x4, x6, x8, x10,

x15, x20, x30, and x60 according to the different light conditions.

3.2.4 Brightness

Brightness refers to the brightness of the image. You can set the brightness value

from 1 to 100 to darken or brighten the image. The higher the value is, the

brighter the image is.

3.2.5 ACCE(Adaptive Contrast & Color Enhancement)

It performs an image enhancement processing to enhance the visibility of an

image by expressing the contrast ratio of the image and improving the edge

information of the image effectively.

You can set the ACCE to OFF, LOW, MIDDLE, and HIGH.

Page 21: hd hikvision ds 2cc51d3s vpir

HD-SDI Camera·User Manual

21

3.2.6 Defog

DEFOG is used in special environment such as fog or rain or in high illumination,

which have lower dynamic range than ordinary environment.

OFF, LOW, MIDDLE, and HIGH are selectable.

3.2.7 Backlight

You can set the Backlight to OFF, BLC, and HSBLC.

Backlight Compensation (BLC)

If there s a strong backlight, the object in front of the backlight will appear

silhouetted or dark. BLC bases on the back area to enhance the brightness of the

whole image, which makes it possible to see the area before the strong backlight

clearly, but the backlight area will be over-exposed.

BLC

GAIN MIDDLEAREA

DEFAULT RETURN RET

BLC Figure 3-3

The GAIN of BLC can be set to High, Middle, Low and OFF, the higher the gain is,

the clearer the image is. Follow the below steps to set a BLC area.

Steps:

1. Move the cursor AREA, and click OK button to enter the area edit interface.

2. Press the OK button up/down/left/right to define the BLC position.

Page 22: hd hikvision ds 2cc51d3s vpir
Page 23: hd hikvision ds 2cc51d3s vpir

HD-SDI Camera·User Manual

23

1. Select HSBLC by setting the OK button to left/right, and press OK to enter the

edit interface.

2. Move the cursor to SELECT and select the area by pressing the OK button to

left/right. Four areas are selectable.

3. Set the display as ON to display the HLC area.

4. Press OK button to enter the position/size edit interface.

5. Press the OK button up/down/left/right to define the position/size.

6. Press OK button to confirm the configuration.

LEVEL

It is adjustable from 0 to 100. If the brightness is higher than the level you set,

the HLC will take effect.

MODE

ALL DAY refers to the HSBLC works all day. Night refers to the HLC only works in

night.

BLACK MASK

ON and OFF are selectable. Only when the Black Mask is set to ON, the HSBLCS

configuration will take effect. If you the set black mask to OFF, the HLCS function

is disabled.

DEFAULT

Selecting DEFAULT will restore all the configured settings to the default.

Page 24: hd hikvision ds 2cc51d3s vpir

HD-SDI Camera·User Manual

24

3.2.8 White Balance (WB)

White balance is the white rendition function of the camera to adjust the color

temperature according to the environment. It can remove the unrealistic color

casts in the image

INDOOR, OUTDOOR, MANUAL, ATW (Auto-tracking White Balance), AWC→SET

are selectable.

INDOOR

Indoor mode is applicable to the environment whose color temperature change

is relatively slight.

OUTDOOR

OUTDOOR mode is applicable to the environment whose color temperature is

relatively large.

MANUAL

Manual mode allows you to adjust the white balance by customizing the Blue

and Red value, which range from 1 to 100.

MANUAL WB

BLUE ---|------ 51 RED ---|------ 50 RETURN RET

Manual White Balance Figure 3-6

Page 25: hd hikvision ds 2cc51d3s vpir

HD-SDI Camera·User Manual

25

ATW

ATW mode means the white balance is continuously being adjusted in real-time

according to the color temperature of the scene illumination.

AWC→SET

The camera will adjust the white balance according to a certain environment. If

the environment is changed, you need to use AWC→SET to adjust the color

temperature again.

3.3 Day & Night

Color, B/W, and EXT are selectable for DAY and NIGHT switches.

COLOR

The image is color in color mode all the time.

B/W

The image is black and white all the time. And the IR LED turns on if the camera is

in night mode.

EXT

The image color switches from color to B/W or from B/W to color automatically

according to the light condition. And the IR LED turns on if the camera is in night

mode.

Page 26: hd hikvision ds 2cc51d3s vpir

HD-SDI Camera·User Manual

26

3.4 NR

NR (Noise Reduction) is used to reduce the noise in the video stream.

Move the cursor to NR, and press confirm to enter the NR submenu.

2D&3D NR

2DNR OFF3DNR ON LEVEL ---|------ 50 SMART NR ONRETURN RET

NR Figure 3-7

2D NR:

2D NR reduces the noise in a single frame to get a gentle image. You can set it ON

or OFF by pressing the OK button left/right.

3D NR:

Compared to traditional general 2D NR technology, 3D NR processes the noise

reduction between two frames instead of in one frame. It can decrease the noise

effect, especially when capturing moving images in low light conditions and

delivering more accurate and sharp image quality.

You can customize the S level and the E level which ranges from 0 to 100 to set

the 3D NR.

Page 27: hd hikvision ds 2cc51d3s vpir

HD-SDI Camera·User Manual

27

3D NR

S-LEVEL |--------- 0 E-LEVEL |--------- 0 RETURN RET

3D NR Figure 3-8

The NR Level ranges from 0 to 100.

SMART NR

Smart NR usually takes effect in cooperation with 3D NR. You can set it to ON to

improve the image fluency. And set it to OFF to disable the SMART NR.

3.5 SPECIAL

In the SPECIAL sub-menu, you can set the camera name, the digital effect of the

image, the motion detection, privacy task, language, dead pixel correction, and

check the version of the camera.

Page 28: hd hikvision ds 2cc51d3s vpir

HD-SDI Camera·User Manual

28

SPECIAL

CAM TITLE ON

D-DFFECT MOTION OFFPRIVACY OFFLANGUAGE ENG

DEFECT RS485 VERSION 121005RETURN RET

Special Figure 3-9

3.5.1 Camera Title

You can name your camera by configuring the CAM TITLE. Move the cursor to

CAM TITLE, set it to ON, and press OK button to enter the edit interface. Up to

15 characters can be selected.

OFF: The camera title will not be displayed.

ON: The camera title will be displayed.

CAM TITLE

0 1 2 3 4 5 6 7 8 9A B C D E F G H I J K

L M N O P Q R S T U V

W X Y Z ▶ → ←↑↓( )

- _ ■ / & ~ , . ← → CLR POS END

C A M E R A 0 1 _ _ _

CAM Title Figure 3-10

Steps:

Page 29: hd hikvision ds 2cc51d3s vpir

HD-SDI Camera·User Manual

29

1. Move the cursor to ←or →, and press OK button to decide the character

position on the dotted line.

2. Move the cursor to select the needed characters, numbers, and symbols.

3. Press OK button to confirm. The selected character will be displayed on the

dotted line below.

4. Move the cursor to POS to edit the camera title position on the screen.

1). Move the cursor to POS.

2). Press OK button to enter the CAM TITLE position setting interface.

3). Press up/down/left/right to change the position of camera title.

4). Press OK button to exit the CAM TITLE position setting interface, and

return to the CAM TITLE menu.

5. Move the cursor to END and press OK button to return to the previous menu.

Note:

Move the cursor to CLR to clear all the characters on the dotted line.

3.5.2 D-effect

D-EFFECT

FREEZE OFFMIRROR OFFD-ZOOM OFFNEG. IMAGE OFFRETURN RET

D-effect Figure 3-11

Page 30: hd hikvision ds 2cc51d3s vpir

HD-SDI Camera·User Manual

30

FREEZE

You can set the freeze function as ON or OFF. When you set it as on, the image is

frozen as still. The live view will stay on the moment you set the freeze ON.

Note:

The mirror function will be disabled if the FREEZE is ON.

MIRROR

This series of camera supports MIRROR function. OFF, MIRROR, V-FLIP, and

ROTATE are selectable.

OFF: The mirror function is disabled.

MIRROR: The image flips 180 degree horizontally

V-FLIP: The image flips 180 degree vertically.

ROTATE: The image flips 180 degrees both horizontally and vertically.

D-ZOOM

You can set the D-ZOOM as ON to zoom in the image. When digital zooming is

processed, no actual pixel gained for the image, the selected area will be

enlarged.

NEG.IMAGE

You can set the NEG IMAGE as ON or OFF, if you set it as on, the bright area and

the dark area of the image are reversed.

3.5.3 Motion

In the user-defined motion detection surveillance area, the moving object can be

detected and the alarm will be triggered.

Page 31: hd hikvision ds 2cc51d3s vpir

HD-SDI Camera·User Manual

31

MOTION SELECT AREA 1DISPLAY ONSENSITIVITY ----|---- 30MOTION VIEW ONDEFAULT RETURN RET

Motion Detection Figure 3-12

Set a Motion Detection Area:

Steps:

1. Move the cursor to DISPLAY, and press OK button to enter the motion

detection edit interface.

2. Press the OK button to up/down/left/right to define the position of the

selected motion area.

3. Press OK button again to enter the area size configuration interface after the

position is defined.

4. Press the OK button up/down/left/right to define the size of the selected area.

5. Select RET to return to the previous menu, or select AGAIN to re-configure the

motion detection area.

SELECT

3 motion detection areas are selectable. Press the OK button left/right to select

the area.

Page 32: hd hikvision ds 2cc51d3s vpir

HD-SDI Camera·User Manual

32

DISPLAY

Display the selected motion area or not.

SENSITIVITY

The sensitivity of the motion detection. The sensitivity value ranges from 0 to 60,

and the higher the sensitivity causes the better response of the detection.

MOTION VIEW

You can choose whether to show the motion view. When you choose ON, once

motion occurred, you can see the transparent red mosaic flickering to show the

exact location where the motion occurs.

DEFAULT

Restore the settings of motion detection.

3.5.4 Privacy

The privacy mask allows you to cover certain areas which you don t want to be

viewed or recorded. Up to 8 privacy areas are configurable.

PRIVACY

SELECT AREA 1

DISPLAY ON

COLOR 1

DEFAULT

RETURN RET

Privacy Masks Figure 3-13

Page 33: hd hikvision ds 2cc51d3s vpir

HD-SDI Camera·User Manual

33

Set a Privacy Area:

Steps:

1. Move the cursor to DISPLAY, and press OK button to enter the privacy mask

edit interface.

2. Press the OK button to up/down/left/right to define the position of the

selected privacy mask area.

3. Press OK button again to enter the area size configuration interface after the

position is defined.

4. Press the OK button up/down/left/right to define the size of the selected area.

5. Select RET to return to the previous menu, or select AGAIN to re-configure the

privacy mask.

SELECT

Select the privacy mask area to configure. Press the OK button left/right to select

the area.

DISPLAY

Set to display the selected area or not.

COLOR

The color of the privacy area, 16 colors are selectable for each privacy mask.

DEFAULT

Restore the settings of privacy mask to the default.

3.5.5 Language

CHN1, CHN2, and ENG are selectable.

Page 34: hd hikvision ds 2cc51d3s vpir

HD-SDI Camera·User Manual

34

3.5.6 Defect

DEFECT

LIVE DPC ON LEVEL ---|-----30STATIC DPC ON

START

LEVEL ---|-----25SENS-UP X8

RETURN RET

Dead Pixel Correction Figure 3-14

LIVE DPC

You can choose ON, OFF and AUTO. If auto is selected, the level is not

configurable.

LEVEL

The level of the LIVE DPC, which ranges from 0 to 60.

STATIC DPC

You can set the static DPC as ON or OFF.

START

Start to correct the dead pixels. Press OK button to start DPC correction if you

see the message of CLOSE THE IRIS THEN PRESS ENTER KEY showing up on the

screen.

LEVEL

The level of the STATIC DPC, which ranges from 0 to 60.

Page 35: hd hikvision ds 2cc51d3s vpir

HD-SDI Camera·User Manual

35

SENS-UP

Adjust the sensor. X2, X4, X6, X8, X10, X15, X20, X30, and X60 are selectable.

3.5.7 RS485

If you want to configure the menu items remotely, you have to set the RS485

parameters of control device the same as those of camera.

RS485

CAM ID 1 ID DISPLAY OFFBAUDRATE 38400

RETURN RET

RS485 Figure 3-15

Camera ID ranges from 0 to 255, which is used to recognize the corresponding

camera.

You can set the camera ID to ON/OFF to display the camera ID or not.

Baud rate ranges 2400 to 38400, which has be the same as that of the control

device.

3.5.8 Version

The software version is listed here.

Page 36: hd hikvision ds 2cc51d3s vpir

HD-SDI Camera·User Manual

36

3.6 ADJUST

In the Adjust sub-menu, you can set the sharpness, the image quality on monitor,

the OSD settings, the Lens Shadow Compensation, and the Video output

standard.

ADJUST

SHARPNESS

MONITOR LCD

OSD

LSC OFFNTSC/PAL PALRETURN RET

Adjust Figure 3-16

3.6.1 Sharpness

SHARPNESS

SHARPNESS ONLEVEL ----|----60

RESOLUTION OFFRETURN RET

Sharpness Figure 3-17

SHARPNESS

Page 37: hd hikvision ds 2cc51d3s vpir

HD-SDI Camera·User Manual

37

Sharpness determines the amount of detail an imaging system can reproduce.

You can set the sharpness as ON and OFF, when sharpness is on, the images

appears clearer and sharper.

LEVEL

The sharpness level is between 0 and 100.

RESOLUTION

You can set the resolution as ON and OFF.

3.6.2 Monitor

Monitor CRT, and Monitor LCD are selectable.

MONITOR CRT

BLACK LEVEL ----|----+0 BLUE GAIN ----|----50

RED GAIN ----|----60

RETURN RET

Monitor CRT Figure 3-18

BLACK LEVEL

-30 to +30 are selectable.

BLUE GAIN

0 to 100 are selectable.

Page 38: hd hikvision ds 2cc51d3s vpir

HD-SDI Camera·User Manual

38

RED GAIN

0 to 100 are selectable.

MONITOR LCD

GAMMA USER 1 BLUE GAIN ----|----50

RED GAIN ----|----50

RETURN RET

Monitor LCD Figure 3-19

GAMMA

Gamma is the name of a nonlinear operation used to code and decode

luminance or tristimulus values in video or still image system

1.00, 0.95, 0.90, 0.85, 0.80, 0.75, 0.70, 0.65, 0.60, 0.55, 0.50, 0.45, USER1, USER2,

and AUTO are selectable.

BLUE GAIN

The value of the blue gain is between 0 and 100.

RED GAIN

The value of the red gain is between 0 and 100.

Page 39: hd hikvision ds 2cc51d3s vpir

HD-SDI Camera·User Manual

39

3.6.3 OSD

OSD

TEXT COLOR 1 OUTLINE ONRETURN RET

OSD Configuration Figure 3-20

TEXT COLOR

There are 8 colors configurable for the OSD menu. Press the OK button to Left or

right to change the color of the OSD.

OUTLINE

You can set whether there is an outline of the text. Press the OK button left or

right to set it ON or OFF.

3.6.4 LSC

Lens Shading Correction (LSC) corrects the phenomenon where the image gets

darkened or blurred on the periphery.

ON and OFF are selectable.

3.6.5 NTSC/PAL

PAL, short for Phase Alternating Lines, is a color encoding system for analog

television used in broadcast television systems in most countries broadcasting at

576i.

Page 40: hd hikvision ds 2cc51d3s vpir

HD-SDI Camera·User Manual

40

NTSC, short for the National Television System Committee, is the analog

television system that is used in most of North America, parts of South America

Myanmar, South Korea, etc.

3.7 RESET

Reset all the settings to the factory default.

3.8 EXIT

Move the cursor to EXIT and click OK button to exit from the menu.

Page 41: hd hikvision ds 2cc51d3s vpir

http://www.sat-alarm.gr/