1242827-T01-B

WADING POOL BATHROOM SINK

CUT-OUT TEMPLATE / INSTALLATION INSTRUCTIONS/

®

K-17890-RLDERRING

TM

� ( )

( )

�

�

�

�

�

�

�

�

�

�

�

�

13mm

TOOLS AND MATERIALS(Not Supplied)�

�

�

�

�

�

�

�

�

�

�

�

�

Template(supplied)

Safety glasses

Pencil

Scissors

Tape measure

Putty knife

Plumbers putty

Hacksaw

Keyhole saw or saber saw

Drill (13mm or 1/2 dia. drill bit or larger)

Adjustable wrench

Pipe wrench

Tubing cutter

BEFORE YOU BEGIN�

�

�

�

�

�

�

�

Observe all local plumbing and buildingcodes.

Inspect the waste and supply tubing;replace if necessary.

Prior to installation, unpack the newlavatory and carefully inspect it fordamage. Return the lavatory to itsprotective carton until you are ready toinstall it.

For replacement installations, make surethe existing cutout is the same or smallersize as the new lavatory.

Use the template supplied with thelavatory to mark correct size cutout.

Kohler lavatory is made according toAmerican National Standard that it canmatch the American lavatory fittings . Anyother lavatory fittings may not fit for kohlerlavatory.

Fixture dimensions are nominal andconform to tolerances established byASME Standards (A112.19.2-2013).The product complies with GB 6952-2015.

�

�

�

�

�

�

�

�

ASME (A112.19.2-2013)

GB 6952-2015

FOR SELF-RIMMING INSTALLATIONCUT ALONG THIS LINE

400 mm

RIM OF LAVATORY

ROUGHING-IN

Kohler reserves the right to change marked dimensions without prior notice.

Unit: mm:

Reference Value

1-1/4" OD

3/8" Hot 3/8" Cold

102

Recommended ADA Installation

686Min

203Min

279

229Min

864

61051

449

19

152295

356

0 Co

IMPORTANT CONSUMER

INFORMATION (

Do not use the product in the water below 0 C.o

CARE AND

CLEANING)

To keep your lavatory looking new, make sure you rinse it out

thoroughly after each use. on this

product, as they will scratch and ruin the surface. Stubborn

stains, paint, or tar can be removed with turpentine or paint

thinner.

Please do not use hard materials (like

scouring pad) to clean product surface, especially the

product logo.

DO NOT USE ABRASIVES

CAUTION:

For Artist Edition Products:

Treat your decorative product just as you would treat your fine

china. The best way to clean it is to use warm water and pat dry

with a cotton cloth or soft sponge. use bristle brushes

or abrasive-backed sponges. They will scratch the decorative

surface.

DO NOT

�

�

1.

2. 5"(127mm)

3.

4.

5.

6.

7.

8.

9.

10.

11.

INSTALL THE LAVATORY

�

�

Choose between a wall-mount or countertop

faucet. Either choice will work, although a

wall-mount faucet is recommended.

The sink shown may differ from your

actual product. The installation steps still apply.

Do not install the

faucet trim until instructed.

NOTE:

Wall-Mount Faucets:

1. Position the

template on the countertop.

Countertop Installations:

2. Faucet spout must be at

least 5"(127 mm) in length.

Use the spout centerline

on the template to ensure faucet clearance.

Wall-Mount Faucet:

Countertop Faucet:

3. Mark the faucet spout,handle, and sink cutout locations on thecountertop.

Re-check the clearance between the lavatory,faucet, backsplash, and cabinet. Adjust thetemplate accordingly.

Countertop Faucet:

4. Drill a pilot hole and cut the countertop opening

along the traced line.

5. Drill the faucet holes.

Install the faucet according to instructions.

Countertop Faucets:

6. Install the drain.

7. Apply a thin, continuous bead of sealant

around the sink opening.

8. Position the sink in the opening. Wipe away

excess sealant. Allow the sealant to cure.

9. Install the faucet trim by

following the instructions.

Wall-Mount Faucets:

10. Complete the water supply and drain

connections.

11. Run water into the sink and check all

connections for leaks.

127Min

Spout Centerline

Spout

Handle

Handle

©

©

Copyright Kohler China Investment Co., Ltd. 2017

2017

KOHLER CHINA INVESTMENT CO., LTD NO.158, JIANG CHANG SAN ROAD,JING'AN DISTRICT, SHANGHAI, PRC POST CODE: 200436

( ) 158 200436