Upload
nat-urwin
View
224
Download
0
Embed Size (px)
Citation preview
8/13/2019 Hair Test 01 - Real Hair
http://slidepdf.com/reader/full/hair-test-01-real-hair 1/14
Hair Test 01 -
Real Hair
8/13/2019 Hair Test 01 - Real Hair
http://slidepdf.com/reader/full/hair-test-01-real-hair 2/14
I wanted to make a chunk of silicone, in the shape of the top of a head, so I could make some hair
this is nothing I need exact replicas of, I could just scoop half a round shape into a fresh block of c
do for my mould.
01.
8/13/2019 Hair Test 01 - Real Hair
http://slidepdf.com/reader/full/hair-test-01-real-hair 3/14
I’d still want this to be nice and smooth like I would make my character’s head, so the smoothinthrough a few different stages. In image 03, I’m using a multi-use soldering iron, this one has a h
clay I’m using can be melted to pour into moulds so I used this advantage to melt round parts of c
easier to smooth off. A few minutes are needed to let the clay cool before smoothing it off with my
it’s just sticky and makes a mess rather than smoothing. So once it cooled enough, I smoothed it as
heated it again for extra smoothness. After the second heating there are some air bubbles visible s
smoothing off with my fingers. The silicone picks up every detail, even finger prints, so it all dep
trying to achieve.
03.04. 05.
8/13/2019 Hair Test 01 - Real Hair
http://slidepdf.com/reader/full/hair-test-01-real-hair 4/14
After the mould is ready, it’s time to mix up the silicone. In my last test with the silicone I think I
much oil paint for the pigmenting, this resulted in a longer cure time (4-5 days). This mix had abou
paint. Then weigh the silicone (I subtracted the 1.6g from the calculation accounting for the cup) a
to the weight of 5% of the silicone. Once the mix is thoroughly folded into each other, pour the silic
from a good height, this lets more air bubbles escape on the way down.
07.08.
8/13/2019 Hair Test 01 - Real Hair
http://slidepdf.com/reader/full/hair-test-01-real-hair 5/14
Image 09 is the silicone freshly poured, there are a few air bubbles rising to the surface which is ex
best way to get rid of these was to just blow on them and they would pop. After 24 hours (with th
silicone had set. Image 10 shows the silicone when it has set, you can see there’s no difference in th
a case of, gently poke it to see if it has cured yet.
11.
09.
8/13/2019 Hair Test 01 - Real Hair
http://slidepdf.com/reader/full/hair-test-01-real-hair 6/14
I de-moulded the skull and had some hair lined up ready to cut and insert. I’d make a piercing into
cocktail stick roughly 3mm deep, then using a dental tool with a rough flat end to it (in image 15), I
hair against the silicone and punch it into the hole. The rubberiness of the silicone held it in place. W
would stick out as an implant.
11.
12. 13.
8/13/2019 Hair Test 01 - Real Hair
http://slidepdf.com/reader/full/hair-test-01-real-hair 7/14
This process was repeated several times, similar to pores in the skin where the hair grows. As this w
to see how the hair would stay, and to test if it would animate if made from real hair, I didn’t worry
the bunches.
16. 17.15.
8/13/2019 Hair Test 01 - Real Hair
http://slidepdf.com/reader/full/hair-test-01-real-hair 8/14
These images show the progression of implanting hair. In image 20 I pierced the silicone at a slante
would stick out at the same angle. In image 21 I bent the hair over to see if I could achieve a combo
implants I had done so far.
20.19.
8/13/2019 Hair Test 01 - Real Hair
http://slidepdf.com/reader/full/hair-test-01-real-hair 9/14
Once I had inserted enough hair to make the skull bushy, I decided to give it a haircut. To make su
comb-over section I wrapped an elastic band around it keeping the longer hair out of the way. I co
find any accidental loops or to remove any straggling hairs too. Then got to cutting this ‘fabul
22. 23. 24. 25.
8/13/2019 Hair Test 01 - Real Hair
http://slidepdf.com/reader/full/hair-test-01-real-hair 10/14
The hair reminded me of a brush because it was sticking out at suck a tight angle
29.28.27.26.
8/13/2019 Hair Test 01 - Real Hair
http://slidepdf.com/reader/full/hair-test-01-real-hair 11/14
The next stage was to apply some hair gel/clay to see if it would give me enough control to be abl
image 31 it shows the hair as it kept popping back to this position, meaning I wasn’t able to anim
this method. To form the held down comb over I had to use something to keep it there, so I cut a sm
and made it into a kind of staple which pushed into the silicone and kept the hair in place. In concl
of hair will not work for what I need. I do like the look of it though, it reminds me of people with c
a load of wax and gel to try and keep it stuck down to their heads.
31.30.
32.
8/13/2019 Hair Test 01 - Real Hair
http://slidepdf.com/reader/full/hair-test-01-real-hair 12/14
33. 34.
35. 36.
8/13/2019 Hair Test 01 - Real Hair
http://slidepdf.com/reader/full/hair-test-01-real-hair 13/14
My next test will be to use wire and coat it in some light brown silicone, very thinly, to give it a rub
wax covered hair. This wire will be able to animate. I’m going to try either 0.1mm or 0.08mm wire
look like hair and not too thick.
35.37. 38.
8/13/2019 Hair Test 01 - Real Hair
http://slidepdf.com/reader/full/hair-test-01-real-hair 14/14
Check out more about‘Mother’s Days’
at:
www.skygecko-nat.blogspot.com