1

HAIER

WASHING MACHINE

Service Manual

PART # WD-8888-83

HAIER AMERICA TRADING, LLC www.haieramerica.com

Service Manual

Haier Group

HLT20E(United States)LAH1212(Mexico)LAH1214(Mexico)

Special No.: SMXQJ100-96-02 Edition: 2004-05-18

Full automatic agitating washer

XQJ100-96

Features

Magical lint Filter

Single-directional agitator

Spray spin soak+wash

Front arranged door, convenient for users

Four adjustable feet

Cold & hot water inlet selection

Mechanical control

Drain up

1. Contents 1

2. 1

3.

4. Specifications

5.

6. 6

7. Net dimension 7

8. 7

9. Parts and functions 9

10. Maintenance service and trouble shooting 10

11. Wiring diagram 14

12. Exploded view 15

13. List of parts 17

Product code illumination and series introduction

Features 2

3

Safety precautions 5

Warning and cautions

Installation and accessory parts

1

CONTENTS

2

FEATURES

Magical lint filter

this model abides the used design method of filter lint and adopts unique magical

lint filter technology, cleaning away your lint stealthily .

Spray spin

Five-step Cold & warm water inlet selection

Soak function

Drain up function

Cabinet with the door open in the front:

It adopts the American local design , and the door which can be opened in the front

is easy to repair.

Zincking steel cabinet

the linear pure-white outlook is simple and clean.

Super capacity for more clothes

Mechanical control, operate easily.

Special structure agitator, produce welter current, wash equably and twist-free.

SPECIFICATIONS

3

ModelHLT20E

(United States)

LAH1212

(Mexico)

LAH1214

(Mexico)

Features for use

Wash capacity kg 10.0 10.0 10.0

Spin capacity kg 10.0 10.0 10.0

Level/Volume L 95/72/51 95/72/51 95/72/51

Residual dampness % 100 100 100

Control model

controller

Normal computerized × × ×

Fuzzy computerized × × ×

Frequency conversion × × ×

Service features

Programs 4 - -

Short cycle × × ×

Inlet heating select

Heating selection × × ×

Spinning cycle (selector) 500/700 500/700 500/700

Spinning cycle (variable) - - -

Start/Pause × × ×

Automatic balancing × × ×

Aesthetics

Cabinet material P=Plastic /Z=Zincking/C=Cold ) Z Z Z

Rolled stainless steel

Inner drum (stainl. steel=s / plastic=p) s s s

Drain type drain up drain up drain up

Door (glass=g / plastic=p) × × ×

Adjustable feet

Technical data

Voltage/frequency V/Hz 120V/60Hz 120V/60Hz 120V/60Hz

Wash power W 800 800 800

Spin power W 780 780 780

Special function

Air-Bubble × × ×

Feet wheel × × ×

Water fall current × × ×

Dimensions (measurements)

Height / built under mm 1115 1115 1115

Width mm 686 686 686

Depth / with open door mm 686 686 686

Net weight kg 73 73 73

NOTES: " " FOR AVALIABLE, "×" FOR NOT AVALIABLE “-”FOR NOT BE APPLICABLE

5

SAFETY PRECAUTIONS

If the power cord is bad, to avoid risk it is required to replace it by the technicians of our special shop or the after-sale service department. Keep the pin of the power plug clean.

Do not share one receptacle with other electric appliances. Do not use it in case that the power plug is damaged or the inserting into the receptacle is loose.

Earth

Do not wash water-proof laundries such as the raincoat, bicycle shelter etc. To avoid abnormal vibration during spinning.

If the power cord is bad, to avoid risk it is required to replace it by the technicians of our special shop or the after-sale service department. Keep the pin of the power plug clean.

Be sure to earth the earthing wire reliably. When the machine is normally using, pleaseput the power plug at the location easily to be inserted and extracted by hand. Be sureto pull the plug off when there'spower failure, or the machine is being moved, cleaned orwhen it is idle.

Do not put the machine at damp place like the bathroom. Never wash it with water.

Do not let the machine share one receptaclewith other electric appliances. If the powerplug is damaged, or the plugging into thereceptacle is loose, do not use the plug anymore.

Do not install or store the washer whereit will be exposed to the weather.

6

WARNING AND CAUTIONS

Do not decompose, repair or alter themachine by yourself.

Do not stretch hands into the working machine. It is dangerous even if the rotation is slow. Take special care ofthe children.

Do not put any hot or heavy items (such as the kettle with hot water ) on the washing machine.

The handicapped or children without care shall not use the machine.

Under certain conditions, hydrogen gas may be produced in a hot water system that hasnot been used for 2 weeks or more. HYDROGEN GAS IS EXPLOSIVE. If the hot water has not been used for such a period, before using the washing machine, turn on all hot faucets and let the water flow from each for several minutes. This will release any accumulated hydrogen gas. As the gasis flammable, do not smoke or use an open flame during this time.

Keep the machine away from directsunlight and heat source like the heater.

Do not wash articles that have been previously cleaned in, washed in, soaked in, or spotted with gasoline, dry-cleaning solvents, other flammable, or explosive substances as they give off vapors that could ignite or explode. Do not add gasoline, dry-cleaning solvents, or otherflammable, or explosive substances tothe wash water. These substances giveoff vapors that could ignite or explode.

PetrolThinner

Unit mm

Figure 1

NET DIMENSION

INSTALLATION AND ACCESSORY PARTS

7

686

686

111

5

The largest allowed slope of the shank base of the machine is 2 . The slanting or rough ground will

result in unstable running or stoppage of the machine. Please adjust it with following methods:

Confirm it's horizontal

Hang the plumb to confirm it's horizontal.

Adjust the adjustable feet1) To twist the adjustable foot, please first lift up the side of the foot slightly, and twist the foot.2) Fasten the nut after adjustment.

Adjust the Installation position

High Low

Adjustable foot

<2

Install the drain hose

Outer drain hose component

Drain hose hook

Drain hose joint

Drain hose clamp

First install the drain hose hook on the parts of outer drain hose component.

Put the drain hose clamp on the outer drain hose,insert the outer drain hose into the joint for it, andthen clutch tightly with drain hose clamp.

Please install and adjust the machine according to the requirement of the manual.

It is very important to your security and correct operating the machine.

8

INSTALLATION AND ACCESSORY PARTS

Usage the drain hose

Hang the outer drain hose on the proper placebefore washing( do not use it toppled downon the ground).

Attend that the outlet of drain hose shall be higherthan the water level in washtub to avoid siphonphenomenon.

<1.2m

Connect the water inlet hoses

Figure 4

Figure 3

Figure 2

C

H

1. Insert a new flat washer into each end of the inlet hoses. Firmly seat the washers in the coupling. ( As figure 2)

2. ttach the water inlet hoses to the hot water faucet and the cold water faucet. Using pliers, tighten the coupling. ( As figure 3) NOTE: Do not over tighten. Damage to the valves can result.

Respectively a

5. Check for leaks (1). Swing the water inlet hose gently to confirm if it is suitable. (2). Turn on the water faucets and check for leaks. A small amount of water might enter the washers. You will drain this later.

3. Run water through both faucets and inlet hoses, into a bucket or laundry tub, to get rid of particles in the water lines that might clog the inlet valves screens.

4. Attach the hose connected with hot water faucet to the HOT water inlet valve(sign with "H'). Attach the hose connected with cold water faucet to the COLD water valve(sign with C ).

( As figure 4)NOTE: Do not over-tighten. Damage to the valves can result.

PARTS AND FUNTIONS

9

Program selector

Softener injection inlet

Bleach injection inlet

Cabinet

Control panel

Control panel seat

Inner tub

Top lid

Water level knob

Temperature knob

Control foot of door switch

Agitator

Adjustable foot(four pieces)

Power line

Water inlet valve

Water absorption cushion

Drain hose joint

Door switch

10

MAINTENANCE SERVICE AND TROUBLE SHOOTING

If you replace the computer sequencer without checking the other components carefully, the

computer sequencer may be damaged again. Therefore, please first check if the other components

working normally before replacing the sequencer in maintenance.

No washing and No water filling

CTrouble-shooting charts

Replace the sequencer

Replace the power cord

Replace the door switch

Repair or replace the wire unit

Check the transmission system.

Replace the motor

Repair the capacity

Repair or replace the wire unit

Pull out the power cord

Replace the water inlet valve

Confirm that there's no power failure, pull the power plug out and insert it tightly again. Then close the top lid , turn the sequencer knob to the wash location and pull it out

Measure the voltage of white & black wires of the two ends of the power

input of the sequencer

Measure the voltage of the two ends of the power cord

Measure the voltage of the door switch with the top lid

close

Insert the plug and measure the voltage of

two ends of the motor

Check if the wire unit is normal?

Check if the capacity is normal? Check if the motor is action?

Measure the voltage of the two ends of the water inlet valve

Yes

No

Infinite

No

No

Yes No

Yes

NoNo

Yes

Yes

Yes

YesNo

The resistance is 0

11

MAINTENANCE SERVICE AND TROUBLE SHOOTING

Rotate to one direction in washing

No draining

Change the gear case

Exist

No

No

No

After insert the plug, turn the

sequencer knob to the drain location

Check the inset is normal

and measure the voltage of two ends of

the drain pump

Check the inset is normal

and measure the voltage of two ends of

the drain motor

Replace the drain pump

Check if the drain pump acts.

Check if the drain motor is normal

Check if the wire unit is normal

No

Yes

No

No

Check if the wire unit is normal?

Replace the sequencer

Replace the sequencer

Repair or replace the wire unitNo

Yes

Yes

Keep filling water

Open the water faucet without switching on the power.

If the water can fill into the water inlet valve.

check if the gas guide system such as gas cell leaks gas

Replace the water inlet valve.

Replace the water level switch.

It leaks gas. Please check and repair the gas guide system.

Please smear 801 glue in installation of the connecting pipe.Please smear 801 glue in installation of the gas cell cover.

No

No

12

MAINTENANCE SERVICE AND TROUBLE SHOOTING

Too much noise in spinning

No

No

Yes

Yes

Yes

Yes

No

No

No

If the washing machine is set horizontally.

If the noise of the gear case is large.

If the hanger is wrongly used.

If the noise of the motor is too much.

If the motor is fastened tightly.

Set the machine horizontally.

Replace the gear gas

Replace the hanger.

Replace the motor.

Fasten the motor.

No

No

Yes

Yes

Yes

Yes

Too much noise in washing

If the noise of the motor is too much.

If the pulsator is rubbing the

bottom of the inner tub.

If the motor fastened tightly.

If the noise of the gear case is too large.

If the belt is too tight or loose.

If the radiating pulley is loose.

Fasten the motor.

Replace the retarder.

Adjust the belt.

Fasten the radiating pulley.

Replace the motor.

Adjust the gap between the

pulsator and inner tub

No

No spinning

Insert the plug and select draining function

Replace the gear case.

Check if the ratchet wheel of the gear

case is at the spot.

Replace the drain motor

At the same time please turn the sequence to every spin location to examine, if three os one place spinning ,replace the sequence.

Yes

13

MAINTENANCE SERVICE AND TROUBLE SHOOTING

Is the water pressure lower?

It is special phenomena forwasher with pump.

Wait for the normal waterpressure before use.

It is the water remained in the factoryinspection of performance.

Phenomenan The reason How to settle

Common phenomena

Phenomena Explanation

The program is setting the drain time. Some time is needed before it starts spinning.

The top lid is not closed.

Is the drain hose put down?Is the drain hose blockedby foreign material?

Is the jointer screw of thewater inlet hose is loose or twisted awry?

Is there power failure?

Is the power plug loose?

Is the machine slanting?Are the laundries slanting in spinning?

Fasten the jointer screwproperly.

If do not need continuedraining, you can raisethe entrance of drain hoseand let water flow backinner tub. .

Close the top lid.

Put down the drain hose. Open and close the top lid once.Clean the foreign material.Open and close the top lid once.

Use it when the power is on.

Insert the power plug tightly.

Level the machine properly.Re-order the laundries.

There may be some water flowing out of the drain hose in the first use of the machine.

Rotate the "Process selector" knob to select "Spin", but it doesn't work.

The water faucet leaks.

During draining, the washer continues draining when pushin programme selector knob.

The machine does not act.

There's abnormal sound inside the machine.

In washing,rinsing,spinning, the machine stops running.

No water filling orfilling slowly

14

WIRING DIAGRAM

Actual Circuit Diagram(Please reference the next page)

There is overload protector installed in the motor. In case that the motor is overload or meets breakdown in working, the protector will act and stop the motor. When the breakdown is removed, the motor will resume normal working.

Figure 5-2

The capacitor should not be assembled if the motor voltage is 220-240V.

Figure 6

BLK

IntermAgit

ORG 6-PM Run Coil

RunLow Motor

High Motor

StartMotor

Blue 4-PM Start Coil

YELWash(CCW)

Spin(CW)

Start Coil(AUX)

Start

RunRED Motor

Spin(CW)

Wash(CCW)

Timer Motor

ActuatorBLUE/WHT Actuator

YEL/WHTPumpPump

Fill

IntermittentSpray

WashWash Temp Switch

Brown

Grey

Rinse

12

3

Pink

YEL/RED

Hot Valve

Cold Valve

RED/BLK Full

ORG

Empty

WHT

WHT

WHT

Lid Switch

L1L2

ThermalProtector Bypass

BLK/WHT

Door switch

Drain pump

Drain motorTimer

Com

Full

EmptyWaterlevel

Switch

Hot valve

Cold valve

Motor

C

M4 M2

M3

M5

M1

M6

L

H

AUX