8/10/2019 H06144 LWD Specs Poster-2

1/1

SPERRY DRILLING

LWD Technology SuiteCommon LWD Specications

Nominal OD 3.125 in. / 79 mm 4.75 in. / 121 mm 6.75 in. / 171 mm 8.00 in. / 203 mm 9.50 in. / 241 mm

Nominal ID 0.8 in. / 20 mm 1.25 in. / 32 mm 1.92 in. / 49 mm 1.92 in. / 49 mm 2.38 in. /60 mm 2.38 in. / 60 mm

Connections 2.75 in. 8 STUB ACME 3.50 in. IF 4.50 in. IF 6.625 in. REG 6.625 in. REG 7.625 in. REG

Make-up torque 1 , 95 0 to 2 ,1 5 0 lb f f t / 2 6 4 to 2 9 2 da N m 9 , 90 0 to 1 0 ,9 0 0 lbf ft / 1 , 34 0 - 1 , 48 0 d a N m 5 3 ,0 0 0 to 5 8 ,0 0 0 lb f f t / 7 ,1 9 0 to 7 , 86 0 d aN m 4 3 ,0 0 0 to 4 8 ,0 0 0 lb f f t / 5 , 80 0 to 6 ,5 0 0 da N m 8 9, 0 00 to 9 1, 0 00 lb f f t / 12 ,1 0 0 to 1 2 ,3 0 0 da N m

Max.dogleg severity gni ta toR 14/100 ft / 30m 14/100 ft / 30m 10/100 ft / 30m 8/100 ft / 30m 8/100 ft / 30m 8/100 ft / 30m

Sliding 30/100 ft / 30m 30/100 ft / 30m 21/100 ft / 30m 14/100 ft / 30m 14/100 ft / 30m 14/100 ft / 30m

Max.mass ow rate1 ,8 00 l bm / mi n. / 81 6 k g/ mi n. 3 ,7 50 l bm /m in . / 1 ,7 00 k g/ m in . 1 0, 00 0 lb m/ mi n. / 4, 53 5 kg /m in . 1 0, 00 0 lb m/ m in . / 4 ,5 35 k g/ m in . 2 0, 00 0 lb m /m in . / 9 ,0 70 k g/ m in . 2 0, 00 0 lb m/ m in . / 9 ,0 70 k g/ m in .

Max.sand content 2% 2% 2% 2% 2% 2%

Max.LCM * Pulser dependent Pulser dependent Pulser dependent Pulser dependent Pulser dependent Pulser dependent

Max.RPM 60 180 180 180 180 180

Max.WOB 15,000 lbs / 6,700 daN 25,000 lbs / 11,000 daN 45,000 lbs / 20,000 daN 60,000 lbs / 27,000 daN 60,000 lbs / 27,000 daN 75,000 lbs / 33,000 daN

Vibration Pleaserefer toDownholeTechnicalSpecicationsI nformation document.

Power Supply Lithiumbattery or downhole generator

* Fibrous LCMmaterialis not recommended and mayleadto interruption of real-time mud pulse telemetry.

30,000to33,000 lbfft/4,070 -4,470daNm

GABI Gamma / At-Bit Inclination Sensor4 3 4 in. 6 3 4 in.

MaximumOD 5.5 in. / 140 mm 7.25 in. / 184 mmHole Size Range 6 . 25 to 7 in . / 1 5 9 to 1 78 m m 8 . 37 5 to 9 . 87 5 in . / 2 13 to 2 5 1 m mLength Added to Motor 1 1. 67 ft / 3 .5 6m 1 5.4 2f t / 4 .7 0mMax.Temperature 302F/ 150CMax.Pressure 20,000psi/ 138MPa

GABI Measurement Specications

Sensor Accuracy 3%Inclinometer Accuracy +/- 0.1Detector Type 4independent scintillation detectorsat 90degrees spacingsGamma Measure PointDistance fromBit

Variable:9.5- 11.5ft / 2 .9- 3 .5m

ABI At-Bit Inclination Sensor4 3 4 in. 6 3 4 in. 8 in. 9 1 2 in.

Hole SizeRange5.75to 7.50in./146to 191mm

8.25to9.875in./210to 251mm

10.5in.to 14.75in./267to 375mm

12.25in.to 30in./311to 762mm

Max.Temperature 302F/ 150CMax.Pressure 18,000psi/ 124MPa

ABI Measurement Specications

Inclinometer AccuracyandValue Range 0.1 @ 2s,0to 180TelemetryType Acoustic toMWD, then positive or negative pulse to surfaceSensor Accuracy 0.15SystemAccuracy 0.5

Sensor Measure Point fromBottomof Motor131in./ 333cmadjustable bent housing,110in. / 279cmxed housing

1 6 in . / 4 1 cm 1 6 in . / 4 1 cm 1 6 in . / 4 1 cm

AcoustiCaliper Tool6 3 4 in. 8 in .

MaximumOD 7 .4 7 in . / 18 9. 9 mm 9 .5 i n. / 2 41 .3 m m

Hole SizeRange8.27to 9.875in./210to 251mm

10.5to 14.75in./267to 375mm

Length 6 ft / 1.83 m 7.75 ft / 2.36 mMax.Temperature 302F/ 150CMax.Pressure 18,000psi/ 124MPa

AcoustiCaliper Measurement Specications

Sensor Type Ultrasonic transceivers(3)Measurements Wellborediameter and shapeAccuracy 0.1in.Measure Point 1 .2 5f t / 0 .3 8m 2 .5 ft / 0 .7 6m

Vibration Measurement Sensors

DDSr Shockand vibration measurementsusing a TriaxialAccelerometer arrangement. Min.,Max., and Ave.RPM measurementsusing dualMagnetometersand a

MEMS Gyroscope.

DDSr sensorsavailable in the DGR,HCIM,IXO,Geo-Pilot,DrillDOC,and GABI tools.

DDS2 Shock and vibration measurementsusing a TriaxialAccelerometer arrangement.

Min.,Max., and Ave.RPM measurementsusing dualMagnetometers. DDS2Sensor ismounted in the M5Integrated LWD tool.

TEM TorsionalEfciencyMonitor measurementsfrom the Geo-Pilot system

shaft rotation. Min.,Max., and Ave.RPM measurementsfrom the Geo-Pilot systemshaft rotation.

TorsionalEfciency Monitor ismounted in allsizesof theGeo-Pilot system.

IVSS Shock and Vibration measurementsusing a single axisAccelerometerarrangement. The IVSS Sensor isavailable in the PWD,CTNand ABI tools.

SVSS Shockand Vibration measurementsusing a dualaxis Accelerometer arrangement. The SVSS Sensor isavailable in the EM,GABI,PCD,and

PCM tools.

DGR Dual Gamma Ray Tool4 3 4 in. 6 3 4 in . 8 in. 9 1 2 in.

MaximumOD5.31in.*, /134.9mm

7.43in.*, /188.7mm

8.00in.*,**, /203.20mm

9.5in. /241mm

LengthIntegralpart of theEWR-PHASE 4

tool4.5 ft / 1.37 m 5.07 ft / 1.55 m

Max.Temperature 302F/ 150C

Max.Pressure 18,000psi/ 124MPa 13,500psi/

93.1MPaDGR Measurement Specications

Detector Type DualGeiger-Mller detector banksSystemAccuracy 5% APIMeasure Point fromBottomof Tool 1 4. 85 f t / 4 .5 m 1 .7 4 f t / 0. 53 m 1 .7 8 f t / 0. 54 m 1 .9 f t / 0 .5 8 m

* High-pressure (25,000 psi/ 172 MPa) tools are available upon request.** High ow (20,000 lbm/min) and high-pressure (25,000 psi/ 172 MPa) tools available upon request. For high-temperature (347 F / 175 C) service in these toolsizes, the gamma module is used.

ALD Azimuthal Lithodensity Sensor4 3 4 in. 6 3 4 in . 8 in.

MaximumOD(Stabilizer)

5.37,5.50,5.75, 6,and 6.37in. /137,140,146,152,and 162mm

8.14,8.25and9.37in./ 207,210and 238mm

12in./ 305mm

Length 1 4 .3 5 f t / 4. 3 7 m 1 4 .5 4 f t / 4. 4 3 m 1 6 .3 1 f t / 4. 9 7 mMax.Temperature*** 302F/ 150C

Max.Pressure* 20,000psi/138MPa 25,000psi/ 172MPa

ALDMeas urement Specications

Density/Pe Detector Type PMT Scintillation DetectorsAcoustic Standoff Detector Type N /A P ie zo el ec tr icDensityMeasurement Range 1.50 3.10g/ccDensityMeasurement Accuracy** 0.025g/ccDensityStatistical Repeatability(1 ) **

0.015g/cc

Pe Factor Measurement Range 1 20Pe Factor Measurement Accuracy 0.25(1 5)Pe Factor Statistical Repeatability(1 ) 3% (1 5)

Acoustic Standoff MeasurementRange N/A 0 3in.

Acoustic Standoff Accuracy N/A 0.05in.DensityMeasure Point fromPinEnd of Tool 5 .2 8 f t / 1 .6 1 m 4 .1 1 ft / 1. 25 m 4 .9 0 f t / 1 .4 9 m

* High-pressure tools are available upon request (25,000 psi/ 172 MPa for 4 3/4-in. tools and 30,000 psi/206 MPa for 6 3/4-in. and 8-in. tools).

** All specications are for a 30-second sample in a 2.2 g/cc formation.***High-temperature (347 F / 175 C) option for 4.75 in. and 6.75 in. tools are available upon request. Allspecications are for a 30-second sample.

Dependent on mud properties and other parameters.

EWR-PHASE 4 Superslim, EWR-PHASE 4and EWR-PHASE 4D Sensor

3 1 8 in. 3 5 8 in . 4 3 4 in. 6 3 4 in. 8 in. 9 1 2 in.

MaximumOD 3 . 25 in / 8 2 . 6 m m 3 . 75 in / 9 5 . 3 m m 5 . 31 in / 1 3 5 m m 7 . 43 in / 1 8 9 m m *8.62in /2 19 m m ** 9 .5 i n. / 2 41 m m

Hole Size Range 3.75to 5.75in./95.3to 146mm4.25to 6in./108to 152mm

5.875to 7.25in./149to 184mm

8.27to 9.875in./210to 251mm

10.5to 14.75in./267to 375mm

12.25to 30in./311to 762mm

Length 1 1. 3 f t / 3 .4 4 m 1 2. 9 ft / 3 .9 3 m 2 2. 5 ft / 6 .8 6 m 1 2. 1 ft / 3 .6 9 m 1 2. 2 f t / 3 .7 2 m 1 2. 2 ft / 3 .7 2 mMax.Temperature 302F/ 150C

Max.Pressure 16,000psi/110MPa20,000psi/ 138MPa

18,000psi/ 124MPa

18,000psi / 124MPa

18,000psi/ 124MPa

13,500psi/ 93.1MPa

EWR-Phase4 Measurement Specications

Measurement Type Electromagnetic Wave Propagation

Measurement Range Phase-Shift Resistivity:0.05to 2,000mAttenuation Resistivity:0.1 to 100mMeasurementAccuracy(LongestSpacing)

0.006mat 1m0.2mat 10m10mat 100m

Measure Point fromBottomof Tool

4 .2 f t / 1. 28 m 5 .6 6 f t / 1. 73 m 7 .8 f t / 2. 38 m 4 .9 f t / 1. 49 m 5 .0 f t / 1. 52 m 5 .0 f t / 1. 52 m

* High-temperature (347F/175C) and high-pressure (25,000 psi/ 172 MPa) tools are available upon specialrequest.

** High-ow (20,000 lbm/min. / 9,070 kg/min) and high-pressure (25,000 psi/ 172 MPa) tools are available upon specialrequest. Their make-up torquerange is 43,000-48,000 ft-lbf (5,800-6,500 daN.m).

High- temperature (347F/175C) tools are available upon specialrequest.

PWD Sensor4 3 4 in. 6 3 4 in. 8 in. 9 1 2 in.

MaximumOD4.75in./120.65mm

6.75in./171.45mm

8.00in.**/2 03 .2 0 mm 9 .5 i n. / 2 4 1. 3m m

Length 9 .2 3 f t / 2 .8 1 m 4 .4 4 ft / 1 .3 5 m 4 .4 4 f t / 1 .3 5 m 4 .3 7 f t / 1 .3 3 mMax.Temperature* 302F/ 150C

Max.Pressure* 18,000psi/ 124.1MPa 13,500psi/93.1MPaPWDMeas urement Specications

Detector Type QuartzMeasurements Annular / internalpressure (psi)Measure Point fromBottomof Tool 5 .5 2 f t / 1 .6 8 m 1 .1 3 ft / 0 .3 4 m 1 .0 8 f t / 0 .3 3 m 1 .0 0 f t / 0 .3 1 m

* High-temperature and high-pressure tools are available upon request.** High ow (20,000 lbm/min) toolavailable upon request.

M5 Integrated LWD Tool6 3 4 i n. 8 in. 9 1 2 in.

MaximumOD 7 . 45 in . / 1 8 9 m m 8 . 25 in . / 2 1 0 m m 9 . 75 in . / 2 4 8 m m

Length 2 3 .6 1 f t / 7. 2 0 m 2 5 .3 4 f t / 7. 7 2 m 2 5 .4 2 f t / 7. 7 5 mMax.Temperature 302F/ 150CMax.Pressure 25,000psi/ 172MPaM5 Measurement Specications

ResistivityMeasurementType

ElectromagneticWave Propagation

ResistivityMeasurementRange

Phase-Shift Resistivity:0.05- 2000mAttenuation Resistivity:0.1- 100m

ResistivityMeasurementAccuracy(Longest Spacing,2MHz,Phase-Shift)

0.002mat 1m0.06mat 10m2.5mat 100m

MeasurePoints (from bottom oftool)PWD Sensor 1 .1 8 f t / 0 .3 6 m 1 .1 4 ft / 0. 35 m 1 .1 6 f t / 0. 35 mAGR Sensor 1 .8 2 f t / 0 .5 5 m 1 .8 5 ft / 0. 56 m 1 .8 6 f t / 0. 57 mEWR-M5Sensor 9 .9 5 f t / 3. 03 m 1 1. 02 f t / 3. 36 m 1 1. 07 f t / 3. 37 m

CTN Compensated Thermal Neutron Sensor4 3 4 in. 6 3 4 in. 8 in.

MaximumOD 5.34in.*,**/136mm7.45in.*,**/189mm

9.75in.*,** /248mm

Length 1 1. 4 ft / 3. 48 m 1 1. 8 f t / 3 .6 0 m 1 7. 5 ft / 5. 33 mMax.Temperature 302F/ 150C

Max.Pressure 20,000psi/138MPa 25,000psi/ 172MPa

CTNMeasurement Specications

PorositySensor Type He-3tubesCaliper Sensor Type N/A Ultrasonic transceivers(x3)CTNMeasurePoint fromBottomof Tool

6 .0 f t / 1. 83 m 2 .2 f t / 0. 67 m 4 .4 f t / 1. 34 m

Caliper Measure Point fromBottomof Tool N/A 5 .6 f t / 1. 71 m 8 .5 f t / 2. 59 m

PorosityMeasurementAccuracy(30-s sample)

0.5pu from0-10pu and 5% from10- 50pu

PorosityStatisticalRepeatability(1 )

1.2pu @ 30pu

Caliper Accuracy N/A 0.1in.

* High-pressure (20,000 psi/ 138 MPa) option for 4.75 in. tools are available upon request.** High-temperature (347 F / 175 C) tools are available upon request. High-ow (20,000 lbm/min) tools are standard on the 8-in. collar.

GeoTap , GeoTap Plus FormationPressure Tester

4 3 4 in. 6 3 4 in. 8 in. 9 1 2 in.

MaximumOD 5 . 25 in . / 13 3 m m 7 . 75 in . / 19 7 m m 9 . 75 in . / 2 4 8 m m 1 0 in. / 2 54 m m

HoleSize Range 5.75- 7 .3in./146- 185mm8.375 10.625in./213 270mm

10.625 16in./270 406mm

12.25 18in./311 464mm

Length 2 4 f t / 7 .3 2 mm 2 8. 4 ft / 8. 66 m 2 6. 7 f t / 8 .1 4 m 2 6. 7 ft / 8. 14 mMax.Temperature 302F/ 150C *Max.Pressure 20,000psi/ 138MPa**

GeoTapMeasu rement Specications

Sampling FrequencyDuring Testing Quartzand Straingauge:5 Hz

MeasurementRange

2000 20,000psi/ 1 .38 138MPa

MeasurementAccuracy (1psi+0.02%FS)

Standard Drawdown(Differential PressureBelow Hydrostatic)

5,000psi/

34MPa

GeoTap 7 ,000psi/ 48MPa

GeoTap Plus5,000psi/ 34MPa

30ccchamber5,000psi/ 34MPa

50ccchamber2,000psi/ 14MPa

MaximumDrawdown(Differential PressureBelow Hydrostatic)

6,000psi/41MPa

GeoTap 8 ,500psi/ 59MPaGeoTap Plus6,000psi/ 41MPa

30ccchamber6,000psi/ 41MPa50ccchamber2,500psi/ 17MPa

Measure Point fromBottomof Tool

7 .1 2 f t / 2. 17 m 7 f t / 2. 14 m 7 .1 2 f t / 2. 17 m 7 .1 2 f t / 2 .1 7 m

* High-temperature (347F / 175C) tools are available upon request.** High pressure (30,000 psi/207 MPa) option for 6.75 in., 8.00 in., and 9.50 in. tools available upon request.

QBAT LWD Sonic Tool4 3 4 in. 6 3 4 in. 8 in. 9 1 2 in.

MaximumOD 5 .6 i n. / 1 4 2 m m 7 .8 i n. / 1 9 8 m m 8 .6 i n. / 2 1 8 m m 1 1. 0 in . / 2 79 m mLength 2 6. 4 ft / 8 . 05 m m 2 0. 3 ft / 6 . 19 m 2 0. 4 ft / 6 . 22 m 2 0. 7 ft / 6 . 31 mMax.Temperature 347F/ 175C *Max.Pressure 25,000psi/ 172MPa**QBATMeasurement Specications

Transducer Type Piezoelectric

Measurementst compressionalt shear (refractedand slower thanuid)

Accuracy 1sec/ft t compressionaland refracted shear 2.5sec/ft t slowshear

Measure Point fromBottomof Tool 9 .6 8 f t / 2 .9 5 m 9 .1 3 f t / 2 .7 8 m 9 .1 7 f t / 2 .8 0 m 9 .2 5 ft / 2 .8 2 m

* Some tools are rated 302F / 150C.** High pressure (30,000 psi / 207 MPa) option for 6.75 in., 8.00 in., and 9.50 in. tools available upon request. High ow (20,000 lbm/min) tools available upon request.

MRIL-WD Sensor4 3 4 in. 6 3 4 in.

MaximumOD 5 .2 5 in . / 13 3. 4 mm 7 .5 i n. / 1 90 .5 m m

Stabilizer SizeOptions 5.75,5.875,6,6.125in./146.1,149.2,152.4, 155.6mm8.25,10.50in./209.6,266.7mm

Hole Size Range 5.875in.- 6 .25in./149.2mm- 158.8mm8.50in.- 10.625in./

215.9mm- 269.9mm

Length** 2 4. 04 f t / 7. 33 m 3 8. 73 f t / 11 .8 0 mMax.Temperature 302F/ 150CMax.Pressure 20,000psi/ 138MPa

MRIL-WDMeasurement Specications

Measurements T1 While Drilling

T1 While SlidingT1 While Drilling

T1or T2 While Sliding

NMR Measurement Accuracy 1pu or 5% (whichever isgreater)Diameter of Investigation 8. 5i n. / 2 1. 6c m 1 4in ./ 35 .6 cmAxial Resolution 4 ft / 1.23 m 4 ft / 1.23 mAxial Resolution (Stationary) 1.8 in. / 4.6 cm 24 in. / 61 cmMaximumLogging Rate T1 mode 7 5 f t/ hr / 22 .9 m / hr 1 20 f t /h r / 3 6. 6 m/ hrMaximumLogging Rate T

2mode N/A 230ft/hr / 70m/hr

Mud Types All,0 .015mminimum All,0 .025mminimumMeasurement Point fromBottomof Tool

5 .8 8f t / 1 .7 9m 6 .7 9f t / 2 .0 8m

** Includes cross-over sub Acquisition-activation dependent Mid-point of antennae

AFR Azimuthal Focused Resistivity Sensor4 3 4 in. 6 3 4 in. 8 in.

Available StabilizerDiameters

5.78,5.90,6.03, 6.40and 6.65in./ 146.8,149.9,153.2,162.6and 168.9mm

8.32and 9.32in. /211.3and236.7mm

12.00in./ 304.8mm

Hole Size Range 5.8756.75in./149 171mm8.5- 9 .5in./216- 241mm 12.25in./ 311mm

Length 1 2. 9 f t / 3. 93 m 1 0. 8 ft / 3 .2 9 m 8 .5 f t / 2. 59 mMax.Temperature 302F/ 150C

Max.Pressure25,000psi/172MPa

22,500psi/155MPa

25,000psi/172MPa

AFRSensor Measurement Specications

Operating Frequencies 4kHz&36kHzResistivityMeasurementOperating Range

0 .2 20,000m

ResistivityMeasurementAccuracy

0-200m, 2%500m 3%1,000m 10%2,000m 20%> 10,000m Gross Indication of Change

Depthsof Investigation 3/ 7*/ 10in.fromboreholewall/ 76/ 178/ 254mmAzimuthal Bins Up to 128bins

Image Resolution1in. (standard) / 0.4in.(high resolution) /25mm (standard) / 10mm (high resolution)

Mud ResistivityOperating Range

0.01 10m0.1100S/m

Mud ResistivityMeasurement Accuracy

5% for conductivity> 1S/m10% for conductivitiesbetween 0.11 S/m20% for conductivities< 0.1S/m

Memory 1GBMeasure Point fromBottomof Tool

7 .7 5 f t / 2. 36 m 5 .3 3 f t / 1. 63 m 4 .0 9 ft / 1 .2 5 m

* 8-inch tooldoes not have the 7 in. spacing

ADR Azimuthal Deep Resistivity Sensor4 3 4 in. 6 3 4 in.

MaximumOD 5 . 36 in . / 13 6 m m 7 . 43 in . / 1 89 m m

HoleSize Range5.875in.- 7 .25in./149mm- 178mm

8.375in.- 10.625in./213mm- 270mm

Length 2 5 .2 8 f t / 7 . 70 m 2 4 .3 4 f t / 7 . 42 mMax.Temperature 302F/ 150CMax.Pressure 25,000psi/ 172MPa

ADR Measurement Specications

Operating Frequencies 125kHz,500kHz,2MHzResistivityMeasurementOperating Range

0.05- 5000m

ResistivityMeasurementAccuracy

1m,0.2%10m, 0.6%100m, 2%1,000m,10%

Depthsof Investigation ~16in.- 18ft / ~0.4- 5 .5mAzimuthal Bins 32Compensated Measure PointfromBottomof Tool

10.9ft / 3 .33m

GeosteeringMeasure Point from

Bottomof ToolMultiple

DrillDOC Tool4 3 4 in. 6 3 4 in. 8 in. 9 1 2 in.

MaximumBodyOD 5 .3 9 in . / 1 36 .9 1 mm 7 .1 90 i n. / 1 82 .6 3 mm 8 .5 08 i n. / 2 16 .2 m m 9 .5 i n. / 2 41 .3 0 mm

Hole SizeRange 5-7/8to 7in.149.23to 177.80mm8-3/8to 9-7/8in.212.73to 250.83mm

10-5/8to 17-1/2in.269.88to 444.50mm

16to 26in.406.40to 660.40mm

Length 8.09 ft / 2.47 m 7.36 ft / 2.24 m 7.36 ft / 2.24 m 7.17 ft / 2.19 mMax.Temperature 347F / 175C 347F / 175C 347F / 175C 347F / 175CMax.Pressure 2 5, 00 0 ps i / 1 72 .4 M Pa 2 5, 00 0 ps i / 1 72 .4 M Pa 2 5, 00 0 p si / 17 2. 4 MP a 2 5, 00 0 p si / 17 2. 4 MP a

DrillDOC Tool Measurement Specications

Operating Range Weight 30,000lbf / 13,345daN 60,000lbf/ 26,689daN 100,000lbf / 44,482daN 75,000lbf / 33,362daNTorque 10,000lbf.ft / 1,356daN.m 30,000lbf.ft / 4,067daN.m 50,000lbf.ft /6,779daN.m 88,000lbf.ft / 11,931daN.mBending 10,000lbs.ft / 1,356daN.m 30,000lbf.ft / 4,067daN.m 45,000lbf.ft / 6,101daN.m 72,500lbf.ft / 9,830daN.m

For more information, contact usat sperry@halliburton.com

Salesof Halliburtonproductsand serviceswillbe inaccord solelywith thetermsand conditionscontained in the

contract betweenHalliburtonandthe customer that is applicable to the sale.

H06144 01/13

2013Halliburton.AllRightsReserved. Printed in the USA

www.halliburton.com