Upload
dangdang
View
222
Download
2
Embed Size (px)
Citation preview
w
Invest in Confidence
Technical handbook - Guide technique
SQX & Combi INTELLI+®
Servomoteurs Quart-de-tour Antidéflagrants
SQX & Combi INTELLI+®
Explosionproof Quarter-turn Actuators
Technical specifications Spécifications techniques
All
data
in t
his
broc
hure
are
giv
en fo
r inf
orm
atio
n on
ly a
nd a
re s
ubje
ct t
o ch
ange
with
out
notic
e.Le
s do
nnée
s co
nten
ues
dans
cet
te b
roch
ure
sont
don
nées
pou
r inf
orm
atio
n et
peu
vent
êtr
e m
odifi
ées
sans
pré
avis
.
Technical handbook - Guide technique
SQX & Combi INTELLI+®
Servomoteurs Quart-de-tour Antidéflagrants
SQX & Combi INTELLI+®
Explosionproof Quarter-turn Actuators
3
4 rue d’Arsonval - CS 70091 - 95505 Gonesse CEDEX FranceTel. : +33 (0)1 34 07 71 00 - Fax : +33 (0)1 34 07 71 01 - [email protected] - www.bernardcontrols.com
TEC0
2-0
7_E
+F_
GR
P_re
v05
Tech
nica
l spe
cifi
cati
ons
/ Sp
écifi
cati
ons
tech
niqu
es
GLOSSAIRE DIRECTIVE ATEX / ATEX DIRECTIVE GLOSSARY
Installation area:Area 1 (gas) & 21 (dust): the explosive atmosphere is likely to occur occasionally in normal operation.
Area 2 (gas) & 22 (dust) : the explosive atmosphere is not likely to occur in normal operation but if it does occur, it will persist for a short period of time only.
WARNINGOur devices have not been designed to be operated
in areas where the risk of getting explosive atmosphere, frequently or during long periods is high
(Area 0 and 20).
Group and category of devices - type of atmosphere:Our actuators are designed for use in Group II industries (surface industries) and are of category 2 (adapted to areas 1, 21, 2 or 22 according to cases).
G: Risk of explosive gaseous atmosphereD: Risk of combustible dust atmosphere
ATEX MarkingII 2 GII 2 D
II 2 G D
Areas of installation1 and 2
21 and 221, 2, 21 and 22
Group of gases:Indicates that the device can be used in an atmosphere with gases of the specified group :
GroupABC
Typical Gas (*)MethanEthylene
Hydrogen Acetylene
(*) Other gas, please consult a notified body (INERIS or LCIE i.e)
Class of temperature:Corresponds to the actuator maximum surface temperature:
ClasseT4T5T6
Max. surface temp.135°C100°C85°C
Type of protection design:
Ex de Ex d
Notion de zone d’installation :Zone 1 (gaz) & 21 (poussières) : l’atmosphère explosive est susceptible de se présenter occasionnellement en fonction-nement normal.
Zone 2 (gaz) & 22 (poussières) : l’atmosphère explosive n’est pas susceptible de se présenter en fonctionnement nor-mal ou si elle se présente néanmoins, elle n’est que de courte durée.
ATTENTIONNotre matériel n’est pas prévu pour un emplacement
où l’atmosphère explosive est présente en permanence, pendant de longues périodes
ou fréquemment (Zones 0 et 20).
Notion de groupe et catégorie de matériel et nature de l’atmosphère :Notre matériel est prévu pour les industries du groupe II (industries de surface) et entre dans la catégorie 2 (adapté aux zones 1, 21, 2 ou 22 suivant les cas).
G : Risque d’atmosphère gazeuse explosibleD : Risque de présence de poussière combustible
Marquage ATEXII 2 GII 2 D
II 2 G D
Zones d’installation1 et 2
21 et 221, 2, 21 et 22
Notion de groupe de gaz :Indique que l’appareil peut être utilisé dans une atmosphère contenant les gaz du groupe spécifié :
GroupeABC
Gaz représentatif (*)MéthaneEthylène
Hydrogène Acétylène
(*) Autre gaz consulter un organisme notifié (par ex. INERIS ou LCIE)
Notion de classe de température :Correspond à la température maxi de surface admissible du matériel :
ClasseT4T5T6
Temp. max. de surface135°C100°C85°C
Notion de type de protection :
Ex de Ex d
4
4 rue d’Arsonval - CS 70091 - 95505 Gonesse CEDEX FranceTel. : +33 (0)1 34 07 71 00 - Fax : +33 (0)1 34 07 71 01 - [email protected] - www.bernardcontrols.com
TEC0
2-0
7_E
+F_
GR
P_re
v05
Tech
nica
l spe
cifi
cati
ons
/ Sp
écifi
cati
ons
tech
niqu
es
TECHNICAL SPECIFICATIONS
SPÉCIFICATIONS TECHNIQUES
GEN
ERA
L
Description
SQX actuators (and STX with gearboxes) offer a wide range of torques.INTELLI+® control offers many advanced solutions. An INTELLI+® controls with SIL2/SIL3 assessment is also available (see dedicated catalog for detailled specifications)
L’offre SQX (et STX avec réducteur) propose une large gamme de couples. Le contrôle INTELLI+® offre différentes fonctions avancées. Une version INTELLI+® de niveau SIL2/SIL3 est également disponible (voir catalogue dédié pour spécifications détaillées)
Torque range Gamme de couples
• Direct : 72 to 800 N.m • With Gearbox : up to 610,000 N.m
• Direct : 72 à 800 N.m • Combi : jusqu’à 610,000 N.m
Type of service Type de fonctionnement
Adapted to process requirements: • On-Off : Class A actuators complying with EN15714-
2 and improved endurance Class A+ actuators• Inching/Positioning: Class B actuators complying
with EN15714-2 and improved endurance Class B+ actuators
• Modulating: Class III actuators with higher duty performance and specification of additional performance criteria compared to EN15714-2 Class C basic design requirements
Adapté aux spécifications du process: • Tout ou Rien: Servomoteurs Classe A conformes à
la norme EN15714-2 et servomoteurs Classe A+ avec une endurance /durée de vie prolongée.
• Positionnement pas à pas: Servomoteurs Classe B conformes à la norme EN15714-2 et servomoteurs Classe B+ avec une endurance /durée de vie prolongée.
• Régulation: Classe III qui offre des performances de fonctionnement supérieures et des critères de performance supplémentaires par rapport à la Classe C de la norme EN15714-2
ENCL
OSU
RE
- PR
OTE
CTIO
N
Casing Enveloppe
• Aluminium die casting • Cover fastened by captive and stainless screws
• Carter en aluminium • Fixations du couvercle par vis imperdables en inox
External Protection Peinture - Protection Exterieur
• Type : polyurethane coating Protection: - Standard: C3 according to ISO 12944 - Option : highly corrosive conditions: C5M • Color: RAL 5002 Blue Other possibilites on request
• Type: peinture polyuréthane en standard Protection: - Standard: C3 selon ISO 12944 - Option: Ambiance fortement corrosive : C5M • Couleur: RAL 5002 bleu Autres options sur demande
Etanchéité Weatherproof • IP68 - 10m /96h • IP68 - 10m / 96h
Explosionproof European Standard ATEX Directive CENELEC Standard INERIS Certificat Antidéflagrant Norme Europe, Directive ATEX, Norme CENELECCertificat INERIS
ATEX Directive 2014/34/UE- CENELEC EN 60079-0, EN60079-1, EN61241-0, EN61241-1 standards As standard: EX db II B T4 (option T5 or T6) and Ex tb IIIC T135°C (option T100°C, T85°C) On request: EX db II C T4 (option T5 or T6)
Directive ATEX 2014/34/UE - Normes CENELEC EN 60079-0, EN60079-1, EN61241-0, EN61241-1 En standard : EX db II B T4 (option T5 ou T6) et Ex tb IIIC T135°C (option T100°C, T85°C) Sur demande : EX db II C T4 (option T5 ou T6)
Explosionproof International Standard IEC ExAntidéflagrant Norme InternationalIEC Ex
IEC Ex - standard IEC 60079-0, IEC60079-1, IEC61241-0, IEC61241-1 standards As standard: EX db II B T4 (option T5 or T6) and Ex tb IIIC T135°C (option T100°C, T85°C) On request: EX db II C T4 (option T5 or T6)
IEC Ex - Normes IEC 60079-0, IEC60079-1, IEC61241-0, IEC61 241-1 En standard : EX db II B T4 (option T5 ou T6) et Ex tb IIIC T135°C (option T100°C, T85°C) Sur demande : EX db II C T4 (option T5 ou T6)
Ambient temperature range ATEX and IEC ExTempérature ambiantede fonctionnement ATEX et IEC Ex
Actuator Marking• GasIIB T4 Gb : -20 ...+70°C / -4 ...+158°FIIB T4 Gb : -60 ...+70°C / -76 ...+158°F (option)IIB T5 (ou T6) Gb : -20 ...+60°C / -4 ...+140°FIIB T5 (ou T6) Gb : -60 ...+60°C /-76 ...+140°F (option)IIC T4 (T5 ouT6) Gb : -20 ...+60°C / -4 ...+140°FIIC T4 (T5 ouT6) Gb : -60 ...+60°C / -76 ...+140°F (option)•DustIIIC T135°C : -20 ...+70°C / -4 ...+158°FIIIC T135°C : -60 ...+70°C / -76 ...+158°F (option)IIIC T100°C (ou T85°C) : -20 ...+60°C / -4 ...+140°FIIIC T100°C (ou T85°C) : -60 ...+60°C / -76 ...+140°F
Marquage servomoteur • Gaz IIB T4 Gb : -20 ...+70°C / -4 ...+158°F IIB T4 Gb : -60 ...+70°C / -76 ...+158°F (option) IIB T5 (ou T6) Gb : -20 ...+60°C / -4 ...+140°F IIB T5 (ou T6) Gb : -60 ...+60°C /-76 ...+140°F (option) IIC T4 (T5 ouT6) Gb : -20 ...+60°C / -4 ...+140°F IIC T4 (T5 ouT6) Gb : -60 ...+60°C / -76 ...+140°F (option) • Poussières IIIC T135°C : -20 ...+70°C / -4 ...+158°F IIIC T135°C : -60 ...+70°C / -76 ...+158°F (option) IIIC T100°C (ou T85°C) : -20 ...+60°C / -4 ...+140°F IIIC T100°C (ou T85°C) : -60 ...+60°C / -76 ...+140°F
Explosionproof Canadian and US Standard NEC/CEC 500/505 Standard C.S.A. and FM CertificatAntidéflagrant Norme Canada et USNorme NEC/CEC 500/505Certificat C.S.A. et FM
NEMA 7 - NEMA 9 enclosure C22-2, UL60079, FM3600, FM3611 and FM3615 standards Class I Group C, D div 1&2 (option Group B)- Class II Group E, F, G div 1&2
Protection NEMA 7 - NEMA 9 Normes C22-2, UL60079, FM3600, FM3611 et FM3615 Classe I Groupe C, D div 1&2 (option Groupe B)- Classe II Groupe E, F, G div 1&2
Vibration resistanceRésistance auxvibrations
1g (9.8 m/s²) at 10-500 Hz. (2g for INTELLI+® with SIL) (Contact our marketing dept. for higher vibration levels).
1g (9.8 m/s²) à 10-500 Hz. (2g pour INTELLI+® avec SIL) (Pour des niveaux de vibration supérieurs, contacter notre service commercial)
5
4 rue d’Arsonval - CS 70091 - 95505 Gonesse CEDEX FranceTel. : +33 (0)1 34 07 71 00 - Fax : +33 (0)1 34 07 71 01 - [email protected] - www.bernardcontrols.com
TEC0
2-0
7_E
+F_
GR
P_re
v05
Tech
nica
l spe
cifi
cati
ons
/ Sp
écifi
cati
ons
tech
niqu
es
MO
TOR
Motor technologyTechnologie moteur
• TENV design (Totally-enclosed, not ventilated) 3-phase or single-phase asynchronous motor, class F insulation with integral thermal overload protection.
• TENV DC motors with 2-wire connection available for some references
• Moteur asynchrone mono ou triphasé de conception TENV (totalement clos, non ventilé), isolation classe F avec protection thermique intégrale contre les surcharges.
• Moteur à courant continu TENV à 2 câbles de branchement disponible pour certaines références.
Motor duty rating Facteur de fonctionnement moteur
• On/Off operation (complying with EN15714-2 Class A) and Inching/Positioning (complying with EN15714-2 Class B): S4 motor duty rating. Up to 360 starts per hour at peak of operation.
• BC Modulating Class III (complying with EN15714- 2 Class C) : S4-50% motor duty rating. Up to 1 200 starts per hour at peak of operation.
• Tout ou Rien (conforme à la norme EN15714-2 Classe A) & Positionnement pas à pas (conforme à la norme EN15714-2 Classe B): facteur de marche de 30% jusqu’à 360 démarrages par heure en pic de fonctionnement
• Régulation Classe III (conforme à la norme EN15714-2 Classe C): facteur de marche de 50% jusqu’à 1200 démarrages par heure en pic de fonctionnement
MEC
HA
NIC
AL
SPEC
IFIC
ATI
ON
Gear design Chaîne cinématique
• Reduction by largely sized worm & wheel gear type • The gears are mechanically self-locking
• Réduction par vis sans fin et roue dentée largement dimensionnées
• Chaîne cinématique mécaniquement irréversible
Manual emergency operation Commande manuelle
Handwheel which does not rotate during motor operation. • Automatic switch between manual and electrical
operation without clutch release lever.• Maximum rim force to apply conform to EN 12570 • Manual controls gear ratio: SQX18-SQX25: 12
travel, SQX50-SQX80: 8 (turns for 90° travel).
Volant ne tournant pas lors du fonctionnement du moteur. • Passage d’un mode à l’autre (manuel - électrique)
automatique sans levier de débrayage.• Force à appliquer conforme à la norme EN 12570 • Mécanique commande manuelle: SQX18-SQX25:
12, SQX50-SQX80: 8 (tours pour une manoeuvre de 90°)
Output flange Bride de sortie Actuator flanges comply with ISO 5211. Les brides sont conformes à la norme ISO 5211.
Lubrication Lubrification
The actuators are lubricated for the product lifetime and do not require any special maitenance.
Les servomoteurs sont lubrifiés pour toute la durée de vie du produit et ne requièrent aucune maintenance spécifique.
ELEC
TRIC
AL
SPEC
IFIC
ATI
ON Power supply
Alimentation électrique
Actuators can operate on a wide variety of power supplies: • single-phase or 3-phase, DC, • up to 690 V (depending on version), • 50 or 60 Hz
Les servomoteurs acceptent une très large gamme d’alimentations : • monophasé ou triphasé, courant continu, • jusqu’à 690 Volts suivant version, • 50 ou 60 Hz
Terminal compartment Connexions électriques
• Ring tongue terminals • Internal ground rod
• Par cosses à oeillet • Bornes masse interne et externe
Fuse protectionProtection fusible
Primary fuse (6.3 x 32mm - 0.5 A) located on the transformer board. 2 automatic fuses for low internal voltages.
Fusible primaire (6.3 x 32 mm - 0.5 A) situé sur le transformateur. Deux fusibles automatiques pour les basses tensions internes.
Conduit entries Entrées de câbles
• Cable glands supplied in option • 2 for signalling : 1’’ NPT • 1 for motor supply : 1’’1/2 NPT • 2 or 4 for fieldbus (option) : 3/4 NPT
• Presse étoupes fournis en option • 2 pour la signalisation : 1’’ NPT • 1 pour l’alimentation moteur : 1’’1/2 NPT • 2 ou 4 pour le bus de terrain (option) : 3/4 NPT
PO
SITI
ON
& T
OR
QU
E SE
NSO
RS
Travel limit systemsSystème de fin de course
• Position: movement reading on output shaft. • Position sensor : Absolute encoder • Détection de position par encodeur absolu
Torque limiting systemSystème de limitation de couple
• Torque: Direct measurment transmitted torque. • The torque limiting system is calibrated in factory
to customer's choice. It remains ajustable via Intelli+ (non intrusive setting)
• Couple : Mesure directe du couple transmis. • Le système limiteur d’effort est calibré en usine au
couple choisi par le client et reste modifiable au travers de l’électronique (paramétrage non-intrusif)
6
4 rue d’Arsonval - CS 70091 - 95505 Gonesse CEDEX FranceTel. : +33 (0)1 34 07 71 00 - Fax : +33 (0)1 34 07 71 01 - [email protected] - www.bernardcontrols.com
TEC0
2-0
7_E
+F_
GR
P_re
v05
Tech
nica
l spe
cifi
cati
ons
/ Sp
écifi
cati
ons
tech
niqu
es
CON
TRO
LS
ControlContrôle
Command by: • voltage: 10 to 250 V DC/AC (current 10 mA at 24V) • dry contact (use INTELLI+® auxiliary 24 VDC supply)
Command Signal Isolated by opto-couplers Minimum command pulse duration: 100ms Time of rotational direction change: 200ms (factory setting range 50 to 500 ms)
Commandes par • tension : 10 à 250 V CC/CA (courant : 10 mA at 24V)• contacts secs (utilise l’alimentation 24 VCC interne de
l’INTELLI+®) Signal de commande isolé par opto-coupleurs Impulsion de commande de durée minimum : 100ms Délai de changement de sens de rotation : 200ms (réglage usine entre 50 à 500 ms)
Visual position indicationIndicateur de position
A LCD screen dial type window provides continuous position indication even in the event of power supply loss using 24VDC back-up supply or optionnal battery.
Un écran LCD fournit une information continue de position, y compris en cas de coupure de l’alimentation de puissance avec alimentation de secours 24VCC ou un batterie optionnelle
Controls LocationBoitier de commande
As standard, the INTELLI+® control is integrated to the actuator. As an option, controls can be mounted in a separated box (max distance between actuator and controls = 50m).
En standard, le contrôle INTELLI+® est intégré au servomoteur. En option, il est possible de proposer un boitier de commande séparé (distance maximum du servomoteur : 50m).
Double sealing protectionDouble-étanchéité
Protection of the electronics: the control compartment of the actuator is fully isolated from the wiring compartment
Pour protéger l’électronique, la partie contrôle du servomoteur est complètement isolée du compartiment de connexion.
Power circuitCircuit d’alimentation
Integral motor reversing starters (electromechanical controls for On-Off Class A / Inching-Positioning Class B / Modulating Class III)
Commande du moteur par contacteurs inverseurs (électromécanique pour Tout ou Rien Classe A / Positionnement: Classe B /Régulation Classe III)
Auxiliary power supplyAlimentation auxiliaire 24VDC in standard. 48VDC as an option. 24VCC en standard. 48VCC en option.
Signal relayRelais de signalisation
4 relays: each information can be freely selected among a total of 23 available information • Contact configuration: normally open or normally
closed• Minimum current 10mA at 5V • Maximum current 5A at 250VAC or 5A at 30VDC (resistive load) Additional 3 relay boards as an option.
4 relais : chaque information peut être sélectionnée parmi 23 informations disponibles • Configuration du contact : normalement ouvert ou
normalement fermé.• Courant minimum : 10 mA à 5 V • Courant maximum : 5 A à 250 VCA ou 5 A à 30 VCC max. (charge resistive) Carte 3 relais supplémentaires en option.
Fault relayRelais défaut
• SPDT monostable relay, in fault position when not supplied.
• Minimum current 10mA at 5V • Maximum current 5A at 250VAC or 5A at 30V DC
(inductive load)
• Relais monostable SPDT, relais en position défaut lorsqu’il est non alimenté • Courant minimum : 10 mA à 5 V
• Courant maximum : 5 A à 250 VCA ou 5 A à 30 VCC max. (charge resistive)
Contrôle Positionnement pas à pas & Régulation (Option)Inching/Positioning & Modulating control (option)
Input (setpoint) and output (feedback) signals are fully isolated from each other Signal configurations (selectable): • Input signal: 4-20 mA - output signal : 4-20mA • Input signal: 0-20 mA - output signal : 0-20mA • Input signal: 0-10 V - output signal : 0-20mA (0-10V
with an external resistor)Analogue inputs • in current: impedance of 160 Ohms • in voltage: impedance of 11 KOhms Analogue outputs: • in current: maximum acceptable load of 750 Ohms
at 24 VDC supply• In voltage: minimum acceptable load of 50 KOhms
(with a shunt resistor of 500 Ohms)
Les signaux d’entrée (consigne) et de sortie (recopie) sont totalement isolés. Configurations des signaux (configurable) : • Signal d’entrée : 4-20 mA – signal de sortie : 4-20mA • Signal d’entrée : 0-20 mA - signal de sortie : 0-20mA • Signal d’entrée : 0-10 V - signal de sortie : 0-20mA
(0-10V avec une résistance externe)Entrées analogiques : • en courant : impédance de 160 Ohms • en tension : impédance de 11 KOhms Sorties analogiques : • en courant: charge maximum acceptable de 750 Ohms
à 24VCC• en tension: charge minimum acceptable de 50 kOhms
(avec un shunt résistif de 500 Ohms)
Transmitter (option)Transmetteur (option)
Proportional position (0/4-20 mA) and torque (4-20 mA) feedback board Analogue outputs: • in current: maximum acceptable load of 750 Ohms
at 24 VDC supply• In voltage: minimum acceptable load of 50 KOhms
(with a shunt resistor of 500 Ohms)
Carte de recopie de position (0/4-20 mA) et couple (4-20 mA). Sorties analogiques : • en courant : charge acceptable maximum de 750
Ohms en alimentation 24 VCC• en tension : charge acceptable minimum de 50
kOhms (avec une résistance-pont de 500 Ohms)
Signaling continuity (option)Continuité de signalisation(option)
Allows to use the display and update the open and closed position information (through the signaling relays or via fieldbus or via Transmitter option) in case of lack of power supply
Permet d’utiliser l’écran et d’actualiser les informations vanne ouverte et fermée (via les relais de signalisation ou via le bus de terrain ou via l’option transmetteur) en cas de perte d’alimentation électrique
7
4 rue d’Arsonval - CS 70091 - 95505 Gonesse CEDEX FranceTel. : +33 (0)1 34 07 71 00 - Fax : +33 (0)1 34 07 71 01 - [email protected] - www.bernardcontrols.com
TEC0
2-0
7_E
+F_
GR
P_re
v05
Tech
nica
l spe
cifi
cati
ons
/ Sp
écifi
cati
ons
tech
niqu
es
SETT
ING
S
SettingsRéglages
Non-Intrusive All actuator settings and parameters are stored in a non-volatile EEPROM memory. Protection by password. Adjustable via Local control; Infrared link or Bluetooth (in option; to keep an high level of security, Bluetooth range is limited to 10m).
Non-Intrusifs. Tout les réglages et paramètre du servomoteur sont stockés dans une mémoire EEPROM nonvolatile. Réglage possible via la commande locale, la liaison infrarouge ou la liaison Bluetooth (en option). Protection par mot de passe (pour conserver un bon niveau de sécurité, la liaison Bluetooth a une portée limitée à 10 m).
Local settingsCommandes locales
The INTELLI+® can be fully set via its local display and selectors Does not require any specific setting tool Local / Remote selector is padloackable
L’INTELLI+® peut être entièrement configuré via les sélecteurs et l’affichage sur le servomoteur, sans aucun autre outil de réglage Protection par cadenas de la commande locale
INTELLI+®KIT (option)
• INTELLI+® SOFT CD-ROM for laptop PC. • Infrared module to connect the laptop (USB) to the
actuator• USB cable (2 meters length max.)
• CD-ROM INTELLI+®SOFT pour PC portable • Module infrarouge pour connecter un PC (USB) au
servomoteur• Câble USB (2 mètres de long maximum)
INTELLI+® POCKET (option)
• Protection: IP65 (option: ATEX II2G EEx ia IICT4) • Shock resistor: 1.2 m on concrete • Communication: - with INTELLI+®: infrared link (40 cm maximum
distance) or bluetooth (up to 10m) - with PC: bluetooth, IRDA, Wifi (802.11b) as a standard• Optional USB station • Operating system : Windows Mobile 2005 • 64Mb RAM + 256Mb storage card
• Protection : IP65 • Résistance aux chocs : 1,2m sur du béton • Communication : - avec INTELLI+® : lien infrarouge (distance de 40 cm
maximum) ou bluetooth (10 m max.)- avec PC : bluetooth, IRDA, Wifi (802.11b) comme standard • Station USB en option • Système d’exploitation : Windows Mobile 2005 • 64Mo RAM + 256Mo carte de stockage
COM
FOR
MIT
Y T
O E
C D
IREC
TIV
ES Compliance with EC Directives Conformité aux directives CE
SQX actuators comply with: • directive 2004/108/EC Electromagnetic compatibility • directive 2006/95/EC Low voltage • the following harmonised standards: EN 61000- 6-4: Generic emissions standard for industrial environments; EN 61000-6-2: Generic immunity standard for industrial environments; EN 60034-1: Rotating electrical machines; EN 60529: Degrees of protection provided by enclosures (IP ratings code)
Les servomoteurs SQX sont conformes à : • la directive 2004/108/EC Compatibilité électromagnétique • la directive 2006/95/EC Basse tension • aux normes harmonisées suivantes : Norme générique émission - Environnement industriel EN 61000-6-4 ; Norme générique immunité standard - Environnement industriel EN 61000-6-2 ; Machines électriques tournantes EN 60034-1 ; Degrés de protection fournis par les enveloppes (code IP) EN 60529
8
4 rue d’Arsonval - CS 70091 - 95505 Gonesse CEDEX FranceTel. : +33 (0)1 34 07 71 00 - Fax : +33 (0)1 34 07 71 01 - [email protected] - www.bernardcontrols.com
TEC0
2-0
7_E
+F_
GR
P_re
v05
FIEL
DB
US
- BU
S D
E TE
RR
AIN
Profibus DPV1 (option)
• PROFIBUS-DPV1 - RS 485• Baud rate: 9.6 kbit/s up to 1.5 Mbit/s (autodetection)• Communication protocol: PROFIBUS DPV1 slave-
cyclic & acyclic• Type of connection: single line (standard) or
redundant line (option)• Cable specification: Profibus certified cable only• Line connection without repeater - Actuators per line: 31 max. - Line length: 1.2 km max. (0.75 mi)• Line connection with repeaters - Number of repeaters per line: 9 max - 30 actuators and 1 Km max. per segment . - Number of actuators per line with repeater: 124
maximum - Line length with 9 repeaters: 10.2 km max. (6.2 mi)• Scan speed (30 units & 1.2 km): 0.1s (at a baud rate
of 93.75 Kbit/s)• Power supply: internal and isolated via INTELLI+®.
24VCC emergency power supply to refresh Open/Close position information in case of loss of electric supply
• Technical approval: operability approved by PNO (Profibus Nutzer Organisation)
• PROFIBUS-DP esclave - RS 485 • Vitesse de transfert : 9.6 kbit/s jusqu’à 1.5 Mbit/s
(auto détection)• Protocole de communication : PROFIBUS DP-V1
esclave-cyclique et acyclique• Type de connexion : simple (standard) ou redondant
(option)• Spécification de câble : exclusivement le câble
Profibus certifié• Connexion sans répéteur : - Nombre de servomoteurs par ligne : 31 max. - Longueur de ligne : 1.2km max. (0.75mi) • Connexion avec répéteurs - Nombre de répéteurs par ligne : 9 max. - 30 servomoteurs et 1km maximum entre deux
répéteurs- Nombre de servomoteurs par ligne avec répéteurs :
124 maximum- Longueur de ligne : 10,2 km max. (6.2 mi) avec 9
répéteurs• Vitesse de balayage (30 unités & 1.2 km) : 0.1s (bus
à 93.75 Kbit/s)• Vitesse de transfert : 9.6 kbit/s jusqu’à 1.5 Mbit/s• Alimentation : interne par le transformateur
INTELLI+®, alimentation externe 24VCC de secours pour raffraîchir les informations de position ouvert/fermé en cas de perte d’alimentation électrique
• Approbation technique : inter-opérabilité testée par le PNO (Profibus Nutzer Organisation)
Modbus (option)
• MODBUS RTU - RS 485 • Transmission medium: 1 shielded pair cable • Functions: Half Duplex, asynchronous mode, multidrop • Baud rate: 1.2k to 115 Kbit/s • Format: 8 data bits, 1 stop bit, no parity • Communication protocol: Modbus (slave) • Modbus address: configurable by the actuator menu
• MODBUS RTU - RS 485 • Support de transmission médium : 1 paire de câbles
blindés• Fonctions : Half Duplex, mode asynchrone, multi-points • Vitesse de transfert : 1.2k à 115Kbit/s • Format : 8 bits de données, 1 bit stop, pas de parité • Protocole de communication : Modbus (esclave) • Adresse Modbus : configurable par le menu du
servomoteur
Foundation Fieldbus (option)
• H1 speed = 31.25kBit/s • Fully compliant with fieldbus standard IEC 61158 • Physical layer: IEC 61158-2, 2 wires communication • Current consumption: 20mA • Operating voltage: 9 to 32 VDC • Cable specification: Type A (for example: 3076F Belden) • Line connection - Actuators per line without repeater: 31 max. - Line length without repeater: 1.9 km max. (1.2 mi) - Number of repeaters per line: 4 max. - Maximum number of actuators and line length
depends on consumption available• Technical approval: Foundation tested. Several DCS
manufacturer operability checked.
• Vitesse H1 = 31.25 kBit/s • Entièrement compatible avec les normes de bus de
terrain IEC 61158• Couche physique : IEC 61158-2, 2 câbles de
communication• Consommation de courant : 20 mA • Tension de fonctionnement : 9 à 32 VCC • Spécifications de câble : type A (par exemple :
3076F Belden)• Connexion de ligne - Servomoteurs par ligne sans répéteur : 31 max. - Longueur de ligne sans répéteur : 1.9km max. (1.2 mi) - Nombre de répéteurs par ligne : 4 max. - Nombre maximum de servomoteurs et longueur de
ligne dépendent de la consommation disponible• Approbation technique : approuvé par le Fieldbus
Foundation. Interopérabilité vérifée avec plusieurs fabricants de DCS
HART (option)
• Interface: HART, 4-20mA current, FSK modulation • Transfer speed: 1.2 kbit/s • Protocol: HART 7.4 • Impedance: 250 Ohms • Power consumption: Internal by INTELLI+®
transformer, External power supply for 4-20mA loop only
• Actuator configuration: Available through EDD file • Connection line: Point-to-Point or Multi-drop • Technical approval: approved by Hart Communication
Foundation
• Interface : HART, courant 4-20mA modulation FSK • Vitesse de transfert: 1.2 kbit/s • Protocole : HART révision 7.4 • Impédance : 250 Ohm • Consommation de courant : Interne par le
transformateur INTELLI+®, alimentation externe pour la boucle 4-20mA uniquement
• Configuration du servomoteur : Disponible via fichier EDD
• Connexion de ligne : Point-à-Point ou Multi-drop • Approbation technique : approuvé par Hart
Communication Foundation
OP
TIO
NS
Option INTELLI+®
• Heating resistor (6W max) • Position feed-back (current loop) • Torque feed-back (current loop) • Fieldbus interface • Signaling continuity • 3 additionnal signaling relays
• Résistance de chauffage ( 6W max) • Recopie de position par boucle de courant • Recopie de couple par boucle de courant • Interface bus de terrain • Continuité de signalisation • 3 relais de signalisation additionnels
Tech
nica
l spe
cifi
cati
ons
/ Sp
écifi
cati
ons
tech
niqu
es
9
4 rue d’Arsonval - CS 70091 - 95505 Gonesse CEDEX FranceTel. : +33 (0)1 34 07 71 00 - Fax : +33 (0)1 34 07 71 01 - [email protected] - www.bernardcontrols.com
TEC0
2-0
7_E
+F_
GR
P_re
v05
Not
es
NOTES
Performances Caractéristiques
All
data
in t
his
broc
hure
are
giv
en fo
r inf
orm
atio
n on
ly a
nd a
re s
ubje
ct t
o ch
ange
with
out
notic
e.Le
s do
nnée
s co
nten
ues
dans
cet
te b
roch
ure
sont
don
nées
pou
r inf
orm
atio
n et
peu
vent
êtr
e m
odifi
ées
sans
pré
avis
.
Technical handbook - Guide technique
SQX & Combi INTELLI+®
Servomoteurs Quart-de-tour Antidéflagrants
SQX & Combi INTELLI+®
Explosionproof Quarter-turn Actuators
11
4 rue d’Arsonval - CS 70091 - 95505 Gonesse CEDEX FranceTel. : +33 (0)1 34 07 71 00 - Fax : +33 (0)1 34 07 71 01 - [email protected] - www.bernardcontrols.com
TEC0
2-0
7_E
+F_
GR
P_re
v05
Per
form
ance
s /
Cara
ctér
isti
ques
1x230V 50Hz On - Off & Inching/PositioningDuty & Mod. Classification S4-30% Motor / Moteur S4-30%
Maxtorque
Nm
Type Operatingtimes/90°
Flange
ISO
On - Off Inching / Positioning
PowerratedkW
Speed
rpm
Currentrated
A
Currentstart
A
Cos
j
Efficiency
%
CoupleMaxNm
Type Tempsmanœuvre
s/90°
Bride
ISO
Tout ou Rien
Positionnement pas à pas
Puissance
kW
Vitesse
tr/min
Courantnominal
A
Courantdémarrage
A
Cos
j
Rendement%
180 SQX18 5 F07/F10 A/A+ - 0,2 1500 2,5 3,5 0,9 39
250 SQX25 5 F07/F10 A/A+ - 0,4 1500 4 9 0,9 41
250 10 A/A+ - 0,1 750 1,8 2,5 0,95 27
250 43 A/A+ B/B+ 0,03 1500 0,6 0,9 0,9 24
600 SQX50 30 F10 A/A+ B/B+ 0,06 1500 1,2 1,7 0,9 24
800 SQX80 30 F12 A/A+ - 0,15 1500 2 3 0,9 36
1000 STX6+RS108 29 F12 (F14) A/A+ B/B+ 0,2 1500 2,5 3,5 0,9 39
1000 15 A/A+ - 0,4 3000 3,5 10 0,99 50
2500 STX6+RS258 69 F16 (F14) A/A+ B/B+ 0,2 1500 2,5 3,5 0,9 39
2500 35 A/A+ - 0,4 3000 3,5 10 0,99 50
4000 STX6G+RS438 64 F16 A/A+ - 0,4 3000 3,5 10 0,99 50
3375 STX20+RS438 47 F16 A/A+ B/B+ 0,3 1500 3,5 15 0,9 41
6210STX20+
SBWG-04-1SM-1/168
110 F16 A/A+ B/B+ 0,3 1500 3,5 15 0,9 41
9280STX6G+ RS1008
191 F25 A/A+ - 0,4 3000 3,5 10 0,99 50
Ces tableaux contiennent une sélection de modèles. En cas de couple plus élevé, de vitesse de sortie différente ou autres tensions, veuillez nous consulter. These tables contain a selection of actuators. For higher torque values, different output speed or other voltages, please consult us.
1x115V 60Hz On - Off & Inching/PositioningDuty & Mod. Classification S4-30% Motor / Moteur S4-30%
Maxtorque
Nm
Type Operatingtimes/90°
Flange
ISO
On - Off Inching / Positioning
PowerratedkW
Speed
rpm
Currentrated
A
Currentstart
A
Cos
j
Efficiency
%
CoupleMaxNm
Type Tempsmanœuvre
s/90°
Bride
ISO
Tout ou Rien
Positionnement pas à pas
Puissance
kW
Vitesse
tr/min
Courantnominal
A
Courantdémarrage
A
Cos
j
Rendement%
200 SQX18 4 F07/F10 A/A+ - 0,36 1800 6 19 0,9 57
250 SQX25 4 F07/F10 A/A+ - 0,36 1800 6 19 0,9 57
250 35 A/A+ B/B+ 0,03 1800 1,3 2 0,9 22
600 SQX50 25 F10 A/A+ B/B+ 0,08 1800 2,2 4 0,9 35
800 SQX80 25 F12 A/A+ - 0,2 1800 4 17 0,9 48
1000 STX6+RS108 24 F12 (F14) A/A+ B/B+ 0,2 1800 4 17 0,9 48
1000 12 A/A+ - 0,37 3600 11 37 0,94 31
2500 STX6+RS258 58 F16 (F14) A/A+ B/B+ 0,2 1800 4 17 0,9 48
2500 30 A/A+ - 0,37 3600 11 37 0,94 31
4000 STX6G+RS438 51 F16 A/A+ - 0,37 3600 11 37 0,94 31
4000 STX20+RS438 57 F16 A/A+ B/B+ 0,37 1800 7,5 43 0,9 63
10000 STX6+RS1008G 178 F25 A/A+ - 0,37 3600 11 37 0,94 31
10000 STX20+RS1008 116 F25 A/A+ B/B+ 0,37 1800 7,5 43 0,9 63
12
4 rue d’Arsonval - CS 70091 - 95505 Gonesse CEDEX FranceTel. : +33 (0)1 34 07 71 00 - Fax : +33 (0)1 34 07 71 01 - [email protected] - www.bernardcontrols.com
TEC0
2-0
7_E
+F_
GR
P_re
v05
Per
form
ance
s /
Cara
ctér
isti
ques
3x400V 50Hz On - Off & Inching/PositioningDuty & Mod. Classification S4-30% Motor / Moteur S4-30%
Maxtorque
Nm
Type Operatingtimes/90°
Flange
ISO
On - Off Inching / Positioning
PowerratedkW
Speed
rpm
Currentrated
A
Currentstart
A
Cos
j
Efficiency
%
CoupleMaxNm
Type Tempsmanœuvre
s/90°
Bride
ISO
Tout ou Rien
Positionnement pas à pas
Puissance
kW
Vitesse
tr/min
Courantnominal
A
Courantdémarrage
A
Cos
j
Rendement%
200 SQX18 5 F07/F10 A/A+ - 0,1 1500 0,6 1 0,55 43
250 SQX25 5 F07/F10 A/A+ - 0,15 1500 0,7 2 0,53 58
300 10 A/A+ - 0,1 750 1,2 2 0,33 37
250 43 A/A+ B/B+ 0,03 1500 0,3 1 0,5 29
600 SQX50 30 F10 A/A+ B/B+ 0,06 1500 0,3 1 0,82 61
800 SQX80 30 F12 A/A+ - 0,1 1500 0,5 1 0,5 58
1000 STX6+RS108 29 F12(14) A/A+ B/B+ 0,1 1500 0,6 1 0,55 43
1000 15 A/A+ - 0,14 3000 0,7 3 0,79 63
1000 6 A/A+ - 0,5 3000 1,6 5 0,9 53
2500 STX6+RS258 69 F16 (F14) A/A+ B/B+ 0,1 1500 0,6 1 0,55 43
2500 35 A/A+ - 0,14 3000 0,7 3 0,79 63
2500 15 A/A+ - 0,5 3000 1,6 5 0,9 53
4000 STX6G+RS438 64 F16 A/A+ - 0,14 3000 0,7 3 0,79 63
4000 27 A/A+ - 0,5 3000 1,6 5 0,9 53
7360STX20+
SBWG-04-1SM-1/168
27 F16 A/A+ - 1,5 3000 3,4 24 0,88 77
10000 STX6+RS1008G 91 F25 A/A+ - 0,5 3000 1,6 5 0,9 53
10000 STX20+RS1008 203 F25 A/A+ B/B+ 0,5 1500 1,8 5 0,78 51
10000 141 A/A+ B/B+ 0,5 1500 1,8 5 0,78 51
15900STX20+
SBWG-05-1SDM-1/540
88 F30 (F25) A/A+ - 1,5 3000 3,4 24 0,88 77
15900STX40+
SBWG-05-1SM-1/180
29 F30 (F25) A/A+ - 2,2 3000 4,4 33 0,89 82
21600STX20+
SBWG-55-1SDM-1/558
91 F30 (F25) A/A+ - 1,5 3000 3,4 24 0,88 77
18200STX40+
SBWG-55-1SM-1/186
46 F30 (F25) A/A+ B/B+ 2,2 1500 5,1 27 0,81 76
32800STX20+
SBWG-06-1SDM-1/1024
128 F35 (F30) A/A+ - 1,5 3000 3,4 24 0,88 77
32200STX40+
SBWG-06-1SBM-1/405
66 F35 (F30) A/A+ - 2,2 3000 4,4 33 0,89 82
40800STX20+
SBWG-07-1SDM-1/1088
177 F40 (F35) A/A+ - 1,5 3000 3,4 24 0,88 77
51100STX40+
SBWG-07-1SDM-1/1088
177 F40 (F35) A/A+ - 2,2 3000 4,4 33 0,89 82
80400STX40+
SBWG-75-1SBM280 F40 (F48) A/A+ - 1,4 3000 2,7 23 0,89 82
81500STX61+
SBWG-75-1SBM107 F40 (F48) A/A+ - 3 3000 5,6 50 0,81 95
121000STX40+
SBWG-08-1SDM-1/1650
206 F48 (F40) A/A+ - 2,2 3000 4,4 33 0,89 82
Ces tableaux contiennent une sélection de modèles. En cas de couple plus élevé, de vitesse de sortie différente ou autres tensions, veuillez nous consulter. These tables contain a selection of actuators. For higher torque values, different output speed or other voltages, please consult us.
13
4 rue d’Arsonval - CS 70091 - 95505 Gonesse CEDEX FranceTel. : +33 (0)1 34 07 71 00 - Fax : +33 (0)1 34 07 71 01 - [email protected] - www.bernardcontrols.com
TEC0
2-0
7_E
+F_
GR
P_re
v05
Per
form
ance
s /
Cara
ctér
isti
ques
3x460V 60Hz On - Off & Inching/PositioningDuty & Mod. Classification S4-30% Motor / Moteur S4-30%
Maxtorque
Nm
Type Operatingtimes/90°
Flange
ISO
On - Off Inching / Positioning
PowerratedkW
Speed
rpm
Currentrated
A
Currentstart
A
Cos
j
Efficiency
%
CoupleMaxNm
Type Tempsmanœuvre
s/90°
Bride
ISO
Tout ou Rien Positionnement pas à pas
Puissance
kW
Vitesse
tr/min
Courantnominal
A
Courantdémarrage
A
Cos
j
Rendement%
180 SQX18 4 F07/F10 A/A+ - 0,11 1800 0,6 1 0,55 43
230 SQX25 4 F07/F10 A/A+ - 0,17 1800 0,7 2 0,53 58
300 8 A/A+ - 0,11 900 1,1 2 0,33 37
250 35 A/A+ B/B+ 0,02 1800 0,2 0,3 0,9 14
600 SQX50 25 F10 A/A+ B/B+ 0,07 1800 0,3 1 0,82 61
800 SQX80 25 F12 A/A+ - 0,11 1800 0,6 1 0,55 43
1000 STX6+RS108 24 F12 (F14) A/A+ B/B+ 0,11 1800 0,6 1 0,55 43
1000 12 A/A+ - 0,15 3600 0,7 3 0,79 63
1000 5 A/A+ - 0,55 3600 1,5 5 0,9 53
2500 STX6+RS258 58 F16 (F14) A/A+ B/B+ 0,11 1800 0,6 1 0,55 43
2500 30 A/A+ - 0,15 3600 0,7 3 0,79 63
2500 13 A/A+ - 0,55 3600 1,5 5 0,9 53
4000 STX20+RS438 57 F16 A/A+ B/B+ 0,55 1800 1,7 5 0,78 51
4000 20 A/A+ - 0,83 3600 2,2 6 0,7 67
8740STX20+
SBWG-04-1SM-1/168
35 F16 A/A+ B/B+ 0,99 1800 2,6 13 0,7 77
7360 23 A/A+ - 1,7 3600 3,2 23 0,88 77
10000 STX6+RS1008G 76 F25 A/A+ - 0,55 3600 1,5 5 0,9 53
10000 STX20+RS1008 171 F25 A/A+ B/B+ 0,55 1800 1,7 5 0,78 51
10000 90 A/A+ - 0,83 3600 2,2 6 0,7 67
15900STX20+
SBWG-05-1SDM-1/540
74 F30 (F25) A/A+ - 1,7 3600 3,2 23 0,88 77
15900STX40+
SBWG-05-1SM-1/180
25 F30 (F25) A/A+ - 2,4 3600 4,2 31 0,89 82
21600STX20+
SBWG-55-1SDM-1/558
76 F30 (F25) A/A+ - 1,7 3600 3,2 23 0,88 77
16640STX40+
SBWG-55-1SM-1/186
38 F30 (F25) A/A+ B/B+ 2,4 1800 4,9 26 0,81 76
32800STX20+
SBWG-06-1SDM-1/1024
107 F35 (F30) A/A+ - 1,7 3600 3,2 23 0,88 77
32200STX40+
SBWG-06-1SBM-1/405
55 F35 (F30) A/A+ - 2,4 3600 4,2 31 0,89 82
40800STX20+
SBWG-07-1SDM-1/1088
148 F40 (F35) A/A+ - 1,7 3600 3,2 23 0,88 77
51100STX40+
SBWG-07-1SDM-1/1088
148 F40 (F35) A/A+ - 2,4 3600 4,2 31 0,89 82
70350STX40+
SBWG-75-1SBM117 F40 (F48) A/A+ - 2,4 3600 4,2 31 0,89 82
81500STX61+
SBWG-75-1SBM89 F40 (F48) A/A+ - 5 3600 8,6 78 0,9 80
121000STX40+
SBWG-08-1SDM-1/1650
172 F48 (F40) A/A+ - 2,4 3600 4,2 31 0,89 82
FXX/FXX: double flange / double brideFXX(FXX): ( )=option
14
4 rue d’Arsonval - CS 70091 - 95505 Gonesse CEDEX FranceTel. : +33 (0)1 34 07 71 00 - Fax : +33 (0)1 34 07 71 01 - [email protected] - www.bernardcontrols.com
TEC0
2-0
7_E
+F_
GR
P_re
v05
Per
form
ance
s /
Cara
ctér
isti
ques
3x440V 50Hz On - Off & Inching/PositioningDuty & Mod. Classification S4-30% Motor / Moteur S4-30%
Maxtorque
Nm
Type Operatingtimes/90°
Flange
ISO
On - Off Inching / Positioning
PowerratedkW
Speed
rpm
Currentrated
A
Currentstart
A
Cos
j
Efficiency
%
CoupleMaxNm
Type Tempsmanœuvre
s/90°
Bride
ISO
Tout ou Rien
Positionnement pas à pas
Puissance
kW
Vitesse
tr/min
Courantnominal
A
Courantdémarrage
A
Cos
j
Rendement%
200 SQX18 5 F07/F10 A/A+ - 0,12 1500 0,5 1,5 0,5 58
250 SQX25 5 F07/F10 A/A+ - 0,24 1500 0,6 2,8 0,69 70
250 43 A/A+ B/B+ 0,02 1500 0,3 0,4 0,9 14
330 SQX50 30 F10 A/A+ B/B+ 0,02 1500 0,3 0,4 0,9 14
800 SQX80 30 F12 A/A+ - 0,12 1500 0,5 1,5 0,5 58
850 STX6+RS108 15 F12 (F14) A/A+ - 0,11 3000 0,5 1,9 0,74 63
850 6 A/A+ - 0,39 3000 1,1 3,5 0,89 86
2500 STX6+RS258 69 F14 (F16) A/A+ B/B+ 0,12 1500 0,5 1,5 0,5 58
2085 35 A/A+ - 0,11 3000 0,5 1,9 0,74 63
2085 15 A/A+ - 0,39 3000 1,1 3,5 0,89 86
4000 STX20+RS438 68 F16 A/A+ B/B+ 0,5 1500 1,4 4,5 0,72 65
4000 47 A/A+ B/B+ 0,5 1500 1,4 4,5 0,72 65
4000 23 A/A+ - 1,2 3000 2,3 16 0,83 77
4000 18 A/A+ B/B+ 0,9 1500 2,5 13 0,61 77
4000 12 A/A+ - 1,5 3000 3,1 22 0,82 77
4000 9 A/A+ - 1,5 3000 3,1 22 0,82 77
2500 6 A/A+ - 1,5 3000 3,1 22 0,82 77
7820STX20+
SBWG-04-1SM-1/168
41 F16 A/A+ B/B+ 0,9 1500 2,5 13 0,61 77
7360 27 A/A+ - 1,5 3000 3,1 22 0,82 77
10000 STX6+RS1008G 418 F25 A/A+ B/B+ 0,12 1500 0,5 1,5 0,5 58
8350 213 A/A+ - 0,11 3000 0,5 1,9 0,74 63
8350 91 A/A+ - 0,39 3000 1,1 3,5 0,89 86
10000 STX20+RS1008 203 F25 A/A+ B/B+ 0,5 1500 1,4 4,5 0,72 65
10000 141 A/A+ B/B+ 0,5 1500 1,4 4,5 0,72 65
15900STX20+
SBWG-05-1SDM-1/540
88 F30 (F25) A/A+ - 1,5 3000 3,1 22 0,82 77
15900STX40+
SBWG-05-1SM-1/180
29 F30 (F25) A/A+ - 2,3 3000 4,4 34 0,81 84
21600STX20+
SBWG-55-1SDM-1/558
91 F30 (F25) A/A+ - 1,5 3000 3,1 22 0,82 77
18200STX40+
SBWG-55-1SM-1/186
46 F30 (F25) A/A+ B/B+ 2,3 1500 5,0 29 0,78 77
32800STX20+
SBWG-06-1SDM-1/1024
128 F35 (F30) A/A+ - 1,5 3000 3,1 22 0,82 77
32200STX40+
SBWG-06-1SBM-1/405
66 F35 (F30) A/A+ - 2,3 3000 4,4 34 0,81 84
40800STX20+
SBWG-07-1SDM-1/1088
177 F40 (F35) A/A+ - 1,5 3000 3,1 22 0,82 77
51100STX40+
SBWG-07-1SDM-1/1088
177 F40 (F35) A/A+ - 2,3 3000 4,4 34 0,81 84
80400STX40+
SBWG75.1SBM280 F40 (F48) A/A+ - 1,7 3000 3 25 0,89 82
81500STX61+
SBWG75.1SBM107 F40 (F48) A/A+ - 3 3000 5,8 45 0,81 84
121000STX40+
SBWG-08-1SDM-1/1650
206 F48 (F40) A/A+ - 2,3 3000 4,4 34 0,81 84
15
4 rue d’Arsonval - CS 70091 - 95505 Gonesse CEDEX FranceTel. : +33 (0)1 34 07 71 00 - Fax : +33 (0)1 34 07 71 01 - [email protected] - www.bernardcontrols.com
TEC0
2-0
7_E
+F_
GR
P_re
v05
Per
form
ance
s /
Cara
ctér
isti
ques
3x500V 50Hz On - Off & Inching/PositioningDuty & Mod. Classification S4-30% Motor / Moteur S4-30%
Maxtorque
Nm
Type Operatingtimes/90°
Flange
ISO
On - Off Inching /Positioning
PowerratedkW
Speed
rpm
Currentrated
A
Currentstart
A
Cos
j
Efficiency
%
CoupleMaxNm
Type Tempsmanœuvre
s/90°
Bride
ISO
Tout ou Rien
Positionnement pas à pas
Puissance
kW
Vitesse
tr/min
Courantnominal
A
Courantdémarrage
A
Cos
j
Rendement%
200 SQX18 5 F07/F10 A/A+ - 0,15 1500 0,6 1,7 0,5 58
250 SQX25 5 F07/F10 A/A+ - 0,15 1500 0,6 1,7 0,5 58
250 SQX25 43 A/A+ B/B+ 0,03 1500 0,3 0,4 0,9 14
420 SQX50 30 F10 A/A+ B/B+ 0,03 1500 0,3 0,4 0,9 14
800 SQX80 30 F12 A/A+ - 0,19 1500 0,5 2,1 0,69 70
1000 STX6+RS108 29 F12 (F14) A/A+ B/B+ 0,15 1500 0,6 1,7 0,5 58
1000 15 A/A+ - 0,26 3000 0,6 2,1 0,94 86
1000 6 A/A+ - 0,5 3000 1,3 4 0,89 86
2500 STX6+RS258 69 F16 (F14) A/A+ B/B+ 0,15 1500 0,6 1,7 0,5 58
2500 35 A/A+ - 0,26 3000 0,6 2,1 0,94 86
2500 15 A/A+ - 0,5 3000 1,3 4 0,89 86
4000 STX20+RS438 47 F16 A/A+ B/B+ 0,74 1500 1,8 9 0,61 77
4000 23 A/A+ - 0,79 3000 1,4 10 0,82 77
4000 18 A/A+ B/B+ 0,9 1500 2,2 11 0,61 77
7820STX20+
SBWG-04-1SM-1/168
41 F16 A/A+ B/B+ 0,9 1500 2,2 11 0,61 77
7360 27 A/A+ - 1,5 3000 2,7 19 0,83 77
10000 STX6+RS1008G 213 F25 A/A+ - 0,26 3000 0,6 2,1 0,94 86
10000 91 F25 A/A+ - 0,5 3000 1,3 4 0,89 86
10000 STX20+RS1008 203 F25 A/A+ B/B+ 0,55 1500 1,3 4 0,64 75
10000 141 A/A+ B/B+ 0,74 1500 1,8 9 0,61 77
15900STX20+
SBWG-05-1SDM-1/540
88 F30 (F25) A/A+ - 1,5 3000 2,7 19 0,83 77
15900STX40+
SBWG-05-1SM-1/180
29 F30 (F25) A/A+ - 2,2 3000 3,5 29 0,89 82
21600STX20+
SBWG-55-1SDM-1/558
91 F30 (F25) A/A+ - 1,5 3000 2,7 19 0,83 77
18200STX40+
SBWG-55-1SM-1/186
46 F30 (F25) A/A+ B/B+ 2,2 1500 4,1 25 0,82 76
32800STX20+
SBWG-06-1SDM-1/1024
128 F35 (F30) A/A+ - 1,5 3000 2,7 19 0,83 77
32200STX40+
SBWG-06-1SBM-1/405
66 F35 (F30) A/A+ - 2,2 3000 3,5 29 0,89 82
40800STX20+
SBWG-07-1SDM-1/1088
177 F40 (F35) A/A+ - 1,5 3000 2,7 19 0,83 77
51100STX40+
SBWG-07-1SDM-1/1088
177 F40 (F35) A/A+ - 2,2 3000 3,5 29 0,89 82
80400STX40+
SBWG-75-1SBM280 F40 (F48) A/A+ - 1,6 3000 2,6 20 0,81 84
81500STX61+
SBWG-75-1SBM107 F40 (F48) A/A+ - 3 3000 5,1 39 0,81 84
121000STX40+
SBWG-08-1SDM-1/1650
206 F48 (F40) A/A+ - 3 3000 5,1 39 0,81 84
FXX/FXX: double flange / double brideFXX(FXX): ( )=option
16
4 rue d’Arsonval - CS 70091 - 95505 Gonesse CEDEX FranceTel. : +33 (0)1 34 07 71 00 - Fax : +33 (0)1 34 07 71 01 - [email protected] - www.bernardcontrols.com
TEC0
2-0
7_E
+F_
GR
P_re
v05
Per
form
ance
s /
Cara
ctér
isti
ques
Per
form
ance
s /
Cara
ctér
isti
ques
3x575V 60Hz On - Off & Inching/PositioningDuty & Mod. Classification S4-30% Motor / Moteur S4-30%
Maxtorque
Nm
Type Operatingtimes/90°
Flange
ISO
On - Off Inching / Positioning
PowerratedkW
Speed
rpm
Currentrated
A
Currentstart
A
Cos
j
Efficiency
%
CoupleMaxNm
Type Tempsmanœuvre
s/90°
Bride
ISO
Tout ou Rien
Positionnement pas à pas
Puissance
kW
Vitesse
tr/min
Courantnominal
A
Courantdémarrage
A
Cos
j
Rendement%
200 SQX18 4 F07/F10 A/A+ - 0,17 1800 0,6 2 0,5 58
230 SQX25 4 F07/F10 A/A+ - 0,17 1800 0,6 2 0,5 58
250 35 A/A+ B/B+ 0,03 1800 0,3 0,4 0,9 14
400 SQX50 25 F10 A/A+ B/B+ 0,03 1800 0,3 0,4 0,9 14
800 SQX80 25 F12 A/A+ - 0,17 1800 0,6 2 0,5 58
1000 STX6+RS108 24 F12 (F14) A/A+ B/B+ 0,17 1800 0,6 2 0,5 58
935 12 A/A+ - 0,15 3600 0,6 2 0,74 63
1000 5 A/A+ - 0,55 3600 1,2 4 0,89 86
1000 STX10+RS108 5 F12 (F14) A/A+ - 0,55 3600 1,2 4 0,89 86
2500 STX6+RS258 58 F14 (F16) A/A+ B/B+ 0,17 1800 0,6 2 0,5 58
2290 30 A/A+ - 0,15 3600 0,6 2 0,74 63
2500 13 A/A+ - 0,55 3600 1,2 4 0,89 86
2500 STX10+RS258 13 F14 (F16) A/A+ - 0,55 3600 1,2 4 0,89 86
4000 STX20+RS438 39 F16 A/A+ B/B+ 0,83 1800 1,5 5 0,71 76
4000 30 A/A+ - 0,55 3600 1,2 4 0,89 86
3750 15 A/A+ B/B+ 0,99 1800 2,1 10 0,61 77
7360STX20+
SBWG-04-1SM-1/168
70 F16 A/A+ - 0,55 3600 1,2 4 0,89 86
6900 35 A/A+ B/B+ 0,99 1800 2,1 10 0,61 77
9185 STX6+RS1008G 178 F25 A/A+ - 0,15 3600 0,6 2 0,74 63
10000 76 F25 A/A+ - 0,55 3600 1,2 4 0,89 86
7540 STX20+RS1008 59 F25 A/A+ - 0,55 3600 1,2 4 0,89 86
8700 44 A/A+ B/B+ 0,99 1800 2,1 10 0,61 77
15900STX20+
SBWG-05-1SDM-1/540
111 F30 (F25) A/A+ B/B+ 0,99 1800 2,1 10 0,61 77
15900STX40+
SBWG-05-1SM-1/180
25 F30 (F25) A/A+ - 2,4 3600 3,3 28 0,89 82
21600STX20+
SBWG-55-1SDM-1/558
233 F30 (F25) A/A+ - 0,55 3600 1,2 4 0,89 86
16120STX40+
SBWG-55-1SM-1/186
38 F30 (F25) A/A+ B/B+ 2,4 1800 3,9 24 0,82 76
32800STX20+
SBWG-06-1SDM-1/1024
210 F35 (F30) A/A+ B/B+ 0,99 1800 2,1 10 0,61 77
32200STX40+
SBWG-06-1SBM-1/405
55 F35 (F30) A/A+ - 2,4 3600 3,3 28 0,89 82
43400STX40+
SBWG-07-1SBM123 F40 (F35) A/A+ B/B+ 2,4 1800 3,9 24 0,82 76
22630STX40+
SBWG-07-1SM-1/272
56 F40 (F35) A/A+ B/B+ 2,4 1800 3,9 24 0,82 76
62310STX40+
SBWG-75-1SBM176 F40 (F48) A/A+ B/B+ 2,4 1800 3,9 24 0,82 76
81500STX61+
SBWG-75-1SBM117 F40 (F48) A/A+ - 3,3 3600 4,9 37 0,81 84
121000STX40+
SBWG-08-1SDM-1/1650
225 F48 (F40) A/A+ - 2,4 3600 3,3 28 0,89 82
Ces tableaux contiennent une sélection de modèles. En cas de couple plus élevé, de vitesse de sortie différente ou autres tensions, veuillez nous consulter. These tables contain a selection of actuators. For higher torque values, different output speed or other voltages, please consult us.
17
4 rue d’Arsonval - CS 70091 - 95505 Gonesse CEDEX FranceTel. : +33 (0)1 34 07 71 00 - Fax : +33 (0)1 34 07 71 01 - [email protected] - www.bernardcontrols.com
TEC0
2-0
7_E
+F_
GR
P_re
v05
Per
form
ance
s /
Cara
ctér
isti
ques
Per
form
ance
s /
Cara
ctér
isti
ques
24VDC On - Off & Inching/PositioningDuty & Mod. Classification S4-30% Motor / Moteur S4-30%
Maxtorque
Nm
Type Operatingtimes/90°
Flange
ISO
On - Off Inching / Posi-tioning
PowerratedkW
Speed
rpm
Currentrated
A
Currentstart
A
Cos
j
Efficiency
%
CoupleMaxNm
Type Tempsmanœuvre
s/90°
Bride
ISO
Tout ou Rien
Positionnement pas à pas
Puissance
kW
Vitesse
tr/min
Courantnominal
A
Courantdémarrage
A
Cos
j
Rendement%
145 SQX18 8 F07/F10 A/A+ - 0,08 1500 6,3 19 1 53
145 SQX25 8 F07/F10 A/A+ - 0,08 1500 6,3 19 1 53
250 64 A/A+ B/B+ 0,08 1500 6,3 19 1 53
600 SQX50 45 F07/F10 A/A+ B/B+ 0,08 1500 6,3 19 1 53
800 SQX80 45 F07/F10 A/A+ - 0,08 1500 6,3 19 1 53
765 STX6+RS108 22 F12 (F14) A/A+ - 0,15 3000 11 31 1 52
2500 STX10+RS258 58 F16 (F14) A/A+ - 0,32 3000 52 122 1 33
5950STX10+
SBWG-04-1SDM-1/504
95 F16 A/A+ - 0,32 3000 61 122 1 33
8350 STX10+RS1008G 136 F25 A/A+ - 0,32 3000 61 122 1 33
48VDC On - Off & Inching/PositioningDuty & Mod. Classification S4-30% Motor / Moteur S4-30%
Maxtorque
Nm
Type Operatingtimes/90°
Flange
ISO
On - Off Inching / Posi-tioning
PowerratedkW
Speed
rpm
Currentrated
A
Currentstart
A
Cos
j
Efficiency
%
CoupleMaxNm
Type Tempsmanœuvre
s/90°
Bride
ISO
Tout ou Rien
Positionnement pas à pas
Puissance
kW
Vitesse
tr/min
Courantnominal
A
Courantdémarrage
A
Cos
j
Rendement%
145 SQX18 8 F07/F10 A/A+ - 0,08 1500 3,7 11 1 45
145 SQX25 8 F07/F10 A/A+ - 0,08 1500 3,7 11 1 45
250 64 A/A+ B/B+ 0,08 1500 3,7 11 1 45
600 SQX50 45 F07/F10 A/A+ B/B+ 0,08 1500 3,7 11 1 45
800 SQX80 45 F07/F10 A/A+ - 0,08 1500 3,7 11 1 45
765 STX6+RS108 22 F12 (F14) A/A+ - 0,15 3000 5,3 15 1 52
2500 STX10+RS258 58 F16 (F14) A/A+ - 0,32 3000 26,0 61 1 33
5950STX10+
SBWG-04-1SDM-1/504
95 F16 A/A+ - 0,32 3000 30,0 61 1 33
8350 STX10+RS1008G 136 F25 A/A+ - 0,32 3000 30,0 61 1 33
FXX/FXX: double flange / double brideFXX(FXX): ( )=option
18
4 rue d’Arsonval - CS 70091 - 95505 Gonesse CEDEX FranceTel. : +33 (0)1 34 07 71 00 - Fax : +33 (0)1 34 07 71 01 - [email protected] - www.bernardcontrols.com
TEC0
2-0
7_E
+F_
GR
P_re
v05
Per
form
ance
s /
Cara
ctér
isti
ques
1x230V 50Hz ModulatingDuty & Mod. Classification
S4-50% Motor / Moteur S4-50%
Maxtorque
Nm
Operating torque
Nm
Type Operatingtimes/90°
Flange
ISO
Modulating Powerrated kW
Speed
rpm
Currentrated
A
Currentstart
A
Cos
j
Efficiency
%
CoupleMaxNm
Couplede manoeuvre
Nm
Type Tempsmanœuvre
s/90°
Bride
ISO
Régulation Puissance
kW
Vitesse
tr/min
Courantnominal
A
Courantdémarrage
A
Cos
j
Rendement%
250 140 SQX25 43 F07/F10 III 0,03 1500 0,6 1 0,9 24
600 250 SQX50 30 F10 III 0,06 1500 1,2 2 0,9 24
1000 30 STX-6+RS108 29 F12 (F14) III 0,2 1500 2,5 4 0,9 39
2500 30 STX-6+RS258 69 F16 (F14) III 0,2 1500 2,5 4 0,9 39
3375 68 STX20+RS438 47 F16 III 0,3 1500 3,5 15 0,9 41
6210 68STX20+SBWG-04-1SM-1/168
110 F16 III 0,3 1500 3,5 15 0,9 41
1x115V 60Hz ModulatingDuty & Mod. Classification
S4-50% Motor / Moteur S4-50%
Maxtorque
Nm
Operating torque
Nm
Type Operatingtimes/90°
Flange
ISO
Modulating Powerrated kW
Speed
rpm
Currentrated
A
Currentstart
A
Cos
j
Efficiency
%
CoupleMaxNm
Couplede manoeuvre
Nm
Type Tempsmanœuvre
s/90°
Bride
ISO
Régulation Puissance
kW
Vitesse
tr/min
Courantnominal
A
Courantdémarrage
A
Cos
j
Rendement%
250 140 SQX25 35 F07/F10 III 0,03 1800 1,3 2 0,9 22
600 250 SQX50 25 F10 III 0,08 1800 2,2 4 0,9 35
1000 30 STX-6+RS108 24 F12 (F14) III 0,2 1800 4 17 0,9 48
2500 30 STX-6+RS258 58 F16 (F14) III 0,2 1800 4 17 0,9 48
4000 100 STX20+RS438 57 F16 III 0,37 1800 7,5 43 0,9 63
10000 88 STX20+RS1008 116 F25 III 0,37 1800 7,5 43 0,9 63
3x400V 50Hz ModulatingDuty & Mod. Classification
S4-50% Motor / Moteur S4-50%
Maxtorque
Nm
Operating torque
Nm
Type Operatingtimes/90°
Flange
ISO
Modulating Powerrated kW
Speed
rpm
Currentrated
A
Currentstart
A
Cos
j
Efficiency
%
CoupleMaxNm
Couplede manoeuvre
Nm
Type Tempsmanœuvre
s/90°
Bride
ISO
Régulation Puissance
kW
Vitesse
tr/min
Courantnominal
A
Courantdémarrage
A
Cos
j
Rendement%
250 140 SQX25 43 F07/F10 III 0,03 1500 0,3 1 0,5 29
600 250 SQX50 30 F10 III 0,06 1500 0,3 1 0,82 61
1000 30 STX-6+RS108 29 F12 (F14) III 0,1 1500 0,6 1 0,55 43
2500 30 STX-6+RS258 69 F16 (F14) III 0,1 1500 0,6 1 0,55 43
4000 100 STX20+RS438 68 F16 III 0,5 1500 1,8 5 0,78 51
4000 100 47 III 0,5 1500 1,8 5 0,78 51
10000 30 STX-6+RS1008G 418 F25 III 0,1 1500 0,6 1 0,55 43
10000 100 STX20+RS1008 203 F25 III 0,5 1500 1,8 5 0,78 51
10000 100 141 III 0,5 1500 1,8 5 0,78 51
18200 175STX40+SBWG-55-1SM-1/186
46 F30 (F25) III 2,2 1500 5,1 27 0,81 76
Ces tableaux contiennent une sélection de modèles. En cas de couple plus élevé, de vitesse de sortie différente ou autres tensions, veuillez nous consulter. These tables contain a selection of actuators. For higher torque values, different output speed or other voltages, please consult us.
19
4 rue d’Arsonval - CS 70091 - 95505 Gonesse CEDEX FranceTel. : +33 (0)1 34 07 71 00 - Fax : +33 (0)1 34 07 71 01 - [email protected] - www.bernardcontrols.com
TEC0
2-0
7_E
+F_
GR
P_re
v05
Per
form
ance
s /
Cara
ctér
isti
ques
3x460V 60Hz ModulatingDuty & Mod. Classification
S4-50% Motor / Moteur S4-50%
Maxtorque
Nm
Operating torque
Nm
Type Operatingtimes/90°
Flange
ISO
Modulating Powerrated kW
Speed
rpm
Currentrated
A
Currentstart
A
Cos
j
Efficiency
%
CoupleMaxNm
Couplede manoeuvre
Nm
Type Tempsmanœuvre
s/90°
Bride
ISO
Régulation Puissance
kW
Vitesse
tr/min
Courantnominal
A
Courantdémarrage
A
Cos
j
Rendement%
250 140 SQX25 35 F07/F10 III 0,02 1800 0,2 0,3 0,9 14
600 250 SQX50 25 F10 III 0,07 1800 0,3 1 0,82 61
1000 30 STX-6+RS108 24 F12 (F14) III 0,11 1800 0,6 1 0,55 43
2500 30 STX-6+RS258 58 F16 (F14) III 0,11 1800 0,6 1 0,55 43
4000 100 STX20+RS438 57 F16 III 0,55 1800 1,7 5 0,78 51
4000 66 15 III 0,99 1800 2,6 13 0,7 77
8740 66STX20+SBWG-04-1SM-1/168
35 F16 III 0,99 1800 2,6 13 0,7 77
10000 30 STX-6+RS1008G 351 F25 III 0,11 1800 0,6 1 0,55 43
10000 100 STX20+RS1008 171 F25 III 0,55 1800 1,7 5 0,78 51
16640 160STX40+SBWG-55-1SM-1/186
38 F30 (F25) III 2,4 1800 4,9 26 0,81 76
3x440V 50Hz ModulatingDuty & Mod. Classification
S4-50% Motor / Moteur S4-50%
Maxtorque
Nm
Operating torque
Nm
Type Operatingtimes/90°
Flange
ISO
Modulating Powerrated kW
Speed
rpm
Currentrated
A
Currentstart
A
Cos
j
Efficiency
%
CoupleMaxNm
Couplede manoeuvre
Nm
Type Tempsmanœuvre
s/90°
Bride
ISO
Régulation Puissance
kW
Vitesse
tr/min
Courantnominal
A
Courantdémarrage
A
Cos
j
Rendement%
250 140 SQX25 43 F07/F10 III 0,02 1500 0,3 0,4 0,9 14
330 137 SQX50 30 F10 III 0,02 1500 0,3 0,4 0,9 14
2500 30 STX-6+RS258 69 F16 (F14) III 0,12 1500 0,5 1,5 0,5 58
4000 100 STX20+RS438 68 F16 III 0,5 1500 1,4 4,5 0,72 65
4000 100 47 III 0,5 1500 1,4 4,5 0,72 65
4000 59 18 III 0,9 1500 2,5 13 0,61 77
7820 59STX20+SBWG-04-1SM-1/168
41 F16 III 0,9 1500 2,5 13 0,61 77
10000 30 STX-6+RS1008G 418 F25 III 0,12 1500 0,5 1,5 0,5 58
10000 100 STX20+RS1008 203 F25 III 0,5 1500 1,4 4,5 0,72 65
10000 100 141 III 0,5 1500 1,4 4,5 0,72 65
18200 175STX40+SBWG-55-1SM-1/186
46 F30(F25) III 2,3 1500 5 29 0,78 77
FXX/FXX: double flange / double brideFXX(FXX): ( )=option
20
4 rue d’Arsonval - CS 70091 - 95505 Gonesse CEDEX FranceTel. : +33 (0)1 34 07 71 00 - Fax : +33 (0)1 34 07 71 01 - [email protected] - www.bernardcontrols.com
TEC0
2-0
7_E
+F_
GR
P_re
v05
Per
form
ance
s /
Cara
ctér
isti
ques
Ces tableaux contiennent une sélection de modèles. En cas de couple plus élevé, de vitesse de sortie différente ou autres tensions, veuillez nous consulter. These tables contain a selection of actuators. For higher torque values, different output speed or other voltages, please consult us.
3x500V 50Hz ModulatingDuty & Mod. Classification
S4-50% Motor / Moteur S4-50%
Maxtorque
Nm
Operating torque
Nm
Type Operatingtimes/90°
Flange
ISO
Modulating Powerrated kW
Speed
rpm
Currentrated
A
Currentstart
A
Cos
j
Efficiency
%
CoupleMaxNm
Couplede manoeuvre
Nm
Type Tempsmanœuvre
s/90°
Bride
ISO
Régulation Puissance
kW
Vitesse
tr/min
Courantnominal
A
Courantdémarrage
A
Cos
j
Rendement%
250 140 SQX25 43 F07/F10 III 0,03 1500 0,3 0,4 0,9 14
420 175 SQX50 30 F10 III 0,03 1500 0,3 0,4 0,9 14
1000 30 STX-6+RS108 29 F12 (F14) III 0,15 1500 0,6 1,7 0,5 58
2500 30 STX-6+RS258 69 F16 (F14) III 0,15 1500 0,6 1,7 0,5 58
4000 100 STX20+RS438 68 F16 III 0,55 1500 1,3 4 0,64 75
4000 100 47 III 0,74 1500 1,8 9 0,61 77
4000 59 18 III 0,9 1500 2,2 11 0,61 77
7820 59STX20+SBWG-04-1SM-1/168
41 F16 III 0,9 1500 2,2 11 0,61 77
10000 30 STX-6+RS1008G 418 F25 III 0,15 1500 0,6 1,7 0,5 58
10000 100 STX20+RS1008 203 F25 III 0,55 1500 1,3 4 0,64 75
10000 100 141 III 0,74 1500 1,8 9 0,61 77
18200 175STX40+SBWG-55-1SM-1/186
46 F30(F25) III 2,2 1500 4,1 25 0,82 76
3x575V 60Hz ModulatingDuty & Mod. Classification
S4-50% Motor / Moteur S4-50%
Maxtorque
Nm
Operating torque
Nm
Type Operatingtimes/90°
Flange
ISO
Modulating Powerrated kW
Speed
rpm
Currentrated
A
Currentstart
A
Cos
j
Efficiency
%
CoupleMaxNm
Couplede manoeuvre
Nm
Type Tempsmanœuvre
s/90°
Bride
ISO
Régulation Puissance
kW
Vitesse
tr/min
Courantnominal
A
Courantdémarrage
A
Cos
j
Rendement%
250 140 SQX25 35 F07/F10 III 0,03 1800 0,3 0,4 0,9 14
400 167 SQX50 25 F10 III 0,03 1800 0,3 0,4 0,9 14
1000 30 STX-6+RS108 24 F12 (F14) III 0,17 1800 0,6 2 0,5 58
2500 30 STX-6+RS258 58 F16 (F14) III 0,17 1800 0,6 2 0,5 58
4000 100 STX20+RS438 39 F16 III 0,83 1800 1,5 5 0,71 76
3750 53 15 III 0,99 1800 2,1 10 0,61 77
6900 53STX20+SBWG-04-1SM-1/168
35 F16 III 0,99 1800 2,1 10 0,61 77
8700 53 STX20+RS1008 44 F25 III 0,99 1800 2,1 10 0,61 77
15900 53STX20+SBWG-05-1SDM-1/540
111 F30 (F25) III 0,99 1800 2,1 10 0,61 77
16120 155STX40+SBWG-55-1SM-1/186
38 F30 (F25) III 2,4 1800 3,9 24 0,82 76
32800 53STX20+SBWG-
06-1SDM-1/1024210 F35 (F30) III 0,99 1800 2,1 10 0,61 77
43400 155STX40+SBWG-
07-1SBM123 F40 (F35) III 2,4 1800 3,9 24 0,82 76
22630 155STX40+SBWG-07-1SM-1/272
56 F40 (F35) III 2,4 1800 3,9 24 0,82 76
62310 155STX40+SBWG-
75-1SBM176 F40 (F48) III 2,4 1800 3,9 24 0,82 76
21
4 rue d’Arsonval - CS 70091 - 95505 Gonesse CEDEX FranceTel. : +33 (0)1 34 07 71 00 - Fax : +33 (0)1 34 07 71 01 - [email protected] - www.bernardcontrols.com
TEC0
2-0
7_E
+F_
GR
P_re
v05
Per
form
ance
s /
Cara
ctér
isti
ques
FXX/FXX: double flange / double brideFXX(FXX): ( )=option
24VDC ModulatingDuty & Mod. Classification
S4-50% Motor / Moteur S4-50%
Maxtorque
Nm
Operating torque
Nm
Type Operatingtimes/90°
Flange
ISO
Modulating Powerrated kW
Speed
rpm
Currentrated
A
Currentstart
A
Cos
j
Efficiency
%
CoupleMaxNm
Couplede manoeuvre
Nm
Type Tempsmanœuvre
s/90°
Bride
ISO
Régulation Puissance
kW
Vitesse
tr/min
Courantnominal
A
Courantdémarrage
A
Cos
j
Rendement%
250 140 SQX25 64 F07/F10 III 0,08 1500 6,3 19 1 53
600 250 SQX50 45 F10 III 0,08 1500 6,3 19 1 53
48 DC ModulatingDuty & Mod. Classification
S4-50% Motor / Moteur S4-50%
Maxtorque
Nm
Operating torque
Nm
Type Operatingtimes/90°
Flange
ISO
Modulating Powerrated kW
Speed
rpm
Currentrated
A
Currentstart
A
Cos
j
Efficiency
%
CoupleMaxNm
Couplede manoeuvre
Nm
Type Tempsmanœuvre
s/90°
Bride
ISO
Régulation Puissance
kW
Vitesse
tr/min
Courantnominal
A
Courantdémarrage
A
Cos
j
Rendement%
250 140 SQX25 64 F07/F10 III 0,08 1500 3,7 11 1 45
600 250 SQX50 45 F10 III 0,08 1500 3,7 11 1 45
Dimensional drawings Plans d’encombrement
All
data
in t
his
broc
hure
are
giv
en fo
r inf
orm
atio
n on
ly a
nd a
re s
ubje
ct t
o ch
ange
with
out
notic
e.Le
s do
nnée
s co
nten
ues
dans
cet
te b
roch
ure
sont
don
nées
pou
r inf
orm
atio
n et
peu
vent
êtr
e m
odifi
ées
sans
pré
avis
.
Technical handbook - Guide technique
SQX & Combi INTELLI+®
Servomoteurs Quart-de-tour Antidéflagrants
SQX & Combi INTELLI+®
Explosionproof Quarter-turn Actuators
All dimensions are given in mm. Toutes les dimensions sont données en mm.
23
4 rue d’Arsonval - CS 70091 - 95505 Gonesse CEDEX FranceTel. : +33 (0)1 34 07 71 00 - Fax : +33 (0)1 34 07 71 01 - [email protected] - www.bernardcontrols.com
TEC0
2-0
7_E
+F_
GR
P_re
v05
Dim
ensi
onal
dra
win
gs /
Pla
ns d
’enc
ombr
emen
t
* Valeur théorique à con�rmer Theoretical value to be con�rmed
Volant de commandemanuelle
Emergency Handwheel
Indicateur de positionPosition indicator
A
Commande localeLocal controls
2x1"+1x1"1/2
RaccordementBus de terrain
(En option)Connection
Fieldbus controls(Optional)
Axe BrideFlange Axis
Raccordementélectrique
Cable entries
Butées réglables limitant larotation à 90° (+/- 2°)
Adjustable mechanical endstops 90° (+/- 2°)
Débrayage volantDeclutching wheel
F07 = 4 x M8Prof./Depth:12
F10 = 4 x M10Prof./Depth:18
Ø70
Ø10
2
Ø12
5
45°
90°
Ø55
493
3
F07 Ø55f8
F10 Ø70f8
Axe BrideFlange Axis
ISO 5211F07/F10
Vue A de la brideView A of the �ange
Rondelle de centrageCentering ring
Douille d'entrainementamovibleRemovable drivesocket
221
80
568
Ø12
8
100
40
336
466
36640
9
13
Ø16
0
* 3
*1
* 1
* 3
* 3
* 2
* 2
SQX18
x' x
y
y'd7
S
x' x
y
y'
Parallel square / Carré Key / Alésage «DoubleD» / Méplat
SOCKET MACHININGUSINAGE DE LA DOUILLE
Socket with 2 positionsDouille avec 2 positions
Standard dimensions S Ød7 SDimensions standard 14 / 17 / 19 / 22 22 / 28 / 30 14 / 17 / 19 / 22
45° machining on request / usinage à 45° sur demande
Weight / Poids33 kg
24
4 rue d’Arsonval - CS 70091 - 95505 Gonesse CEDEX FranceTel. : +33 (0)1 34 07 71 00 - Fax : +33 (0)1 34 07 71 01 - [email protected] - www.bernardcontrols.com
TEC0
2-0
7_E
+F_
GR
P_re
v05
Dim
ensi
onal
dra
win
gs /
Pla
ns d
’enc
ombr
emen
t
* Valeur théorique à con�rmer Theoretical value to be con�rmed
Volant de commandemanuelle
Emergency Handwheel
Indicateur de positionPosition indicator
A
Commande localeLocal controls
2x1"+1x1"1/2
RaccordementBus de terrain
(En option)Connection
Fieldbus controls(Optional)
Axe BrideFlange Axis
Raccordementélectrique
Cable entries
Butées réglables limitant larotation à 90° (+/- 2°)
Adjustable mechanical endstops 90° (+/- 2°)
Débrayage volantDeclutching wheel
F07 = 4 x M8Prof./Depth:12
F10 = 4 x M10Prof./Depth:18
Ø70
Ø10
2
Ø12
5
45°
90°
Ø55
493
3
F07 Ø55f8
F10 Ø70f8
Axe BrideFlange Axis
ISO 5211F07/F10
Vue A de la brideView A of the �ange
Rondelle de centrageCentering ring
Douille d'entrainementamovibleRemovable drivesocket
Débrayage MoteurDeclutching Motor
221
616
100
40
336
466
36640
9
13
Ø12
8
80
Ø16
0
* 1
* 3
* 3
* 2
* 2
*1
* 3
SQX25
x' x
y
y'd7
S
x' x
y
y'
Parallel square / Carré Key / Alésage «DoubleD» / Méplat
SOCKET MACHININGUSINAGE DE LA DOUILLE
Socket with 2 positionsDouille avec 2 positions
Standard dimensions S Ød7 SDimensions standard 14 / 17 / 19 / 22 22 / 28 / 30 14 / 17 / 19 / 22
45° machining on request / usinage à 45° sur demande
Weight / Poids35 kg
25
4 rue d’Arsonval - CS 70091 - 95505 Gonesse CEDEX FranceTel. : +33 (0)1 34 07 71 00 - Fax : +33 (0)1 34 07 71 01 - [email protected] - www.bernardcontrols.com
TEC0
2-0
7_E
+F_
GR
P_re
v05
Dim
ensi
onal
dra
win
gs /
Pla
ns d
’enc
ombr
emen
t
* Valeur théorique à con�rmer Theoretical value to be con�rmed
Volant de commandemanuelle
Emergency Handwheel
Indicateur de positionPosition indicator
A
Commande localeLocal controls
2x1"+1x1"1/2
RaccordementBus de terrain
(En option)Connection
Fieldbus controls(Optional)
Axe BrideFlange Axis
Axe BrideFlange Axis
Raccordementélectrique
Cable entries
Butées réglables limitant larotation à 90° (+/- 2°)
Adjustable mechanical endstops 90° (+/- 2°)
Ø55
483
F10 Ø70f8
Débrayage volantDeclutching wheel
F07 = 4 x M8Prof./Depth:12
F10 = 4 x M10Prof./Depth:18
Ø70
Ø10
2
Ø12
5
Rondelle de centrageCentering ring
Douille d'entrainementamovibleRemovable drivesocket
Débrayage MoteurDeclutching Motor
ISO 5211F07/F10
Vue A de la brideView A of the �ange
100
40
Ø12
8222.5
617
336
466
1336
6409
Ø25
0
80
* 3
* 3*1
* 3
* 1
* 2
* 2
SQX50
S
x' x
y
y'
x' x
y
y'd7
S
x' x
y
y'
Parallel square / Carré Key / Alésage «DoubleD» / Méplat
SOCKET MACHININGUSINAGE DE LA DOUILLE
Socket with 4 positionsDouille avec 4 positions
Standard dimensions S Ød7 SDimensions standard 14 / 17 / 19 / 22 / 27 22 / 28 / 30 / 32 14 / 17 / 19 / 22
45° machining on request / usinage à 45° sur demande
Weight / Poids36 kg
26
4 rue d’Arsonval - CS 70091 - 95505 Gonesse CEDEX FranceTel. : +33 (0)1 34 07 71 00 - Fax : +33 (0)1 34 07 71 01 - [email protected] - www.bernardcontrols.com
TEC0
2-0
7_E
+F_
GR
P_re
v05
Dim
ensi
onal
dra
win
gs /
Pla
ns d
’enc
ombr
emen
t
* Valeur théorique à con�rmer Theoretical value to be con�rmed
Volant de commandemanuelle
Emergency Handwheel
Indicateur de positionPosition indicator
A
Commande localeLocal controls
2x1"+1x1"1/2
RaccordementBus de terrain
(En option)Connection
Fieldbus controls(Optional)
Axe BrideFlange Axis Axe Bride
Flange Axis
Raccordementélectrique
Cable entries
Butées réglables limitant larotation à 90° (+/- 2°)
Adjustable mechanical endstops 90° (+/- 2°)
Débrayage volantDeclutching wheel
81
Ø65
3.2
F12 Ø85f8
2 x Vis CHC M4x6
F12 = 4 x M12Prof./Depth:18
Ø15
0
Ø12
5
Débrayage MoteurDeclutching Motor
Rondelle de centrageCentering ring
Douille d'entrainementamovibleRemovable drivesocket
Rondelle plateFlat ring
ISO 5211F12
Vue A de la brideView A of the �ange
Ø12
8
80
Ø25
0
222
617
100
40
336
466
39744
0
90°
45°
*1
* 3
* 1
* 3
* 3
* 2
* 2
SQX80
S
x' x
y
y'
x' x
y
y'd7
S
x' x
y
y'
Parallel square / Carré Key / Alésage «DoubleD» / Méplat
SOCKET MACHININGUSINAGE DE LA DOUILLE
Socket with 4 positionsDouille avec 4 positions
Standard dimensions S Ød7 SDimensions standard 22 / 27 / 36 22 / 28 / 30 / 35 / 40 14 / 17 / 19 / 22
45° machining on request / usinage à 45° sur demande
Weight / Poids39 kg
27
4 rue d’Arsonval - CS 70091 - 95505 Gonesse CEDEX FranceTel. : +33 (0)1 34 07 71 00 - Fax : +33 (0)1 34 07 71 01 - [email protected] - www.bernardcontrols.com
TEC0
2-0
7_E
+F_
GR
P_re
v05
Dim
ensi
onal
dra
win
gs /
Pla
ns d
’enc
ombr
emen
t
S
x' x
y
y'
x' x
y
y'd7
S
x' x
y
y'
Parallel square / Carré Key / Alésage «DoubleD» / Méplat
SOCKET MACHININGUSINAGE DE LA DOUILLE
Socket with 32 positionsDouille avec 32 positions
Standard dimensions S Ød7 SDimensions standard 22 / 27 / 36 28 / 30 / 35 / 40 / 48 / 50 / 60 32 / 36
Volant de commandemanuelle
Emergency Handwheel
B
Commande localeLocal controls
2x1"+1x1"1/2
RaccordementBus de terrain
(En option)Connection
Fieldbus controls(Optional)
Raccordementélectrique
Cable entries
Indicateur de positionPosition indicator
Rond
elle
pla
teFl
at ri
ng
4
Ø17
5
Ø10
0.5
Indicateur de positionPosition indicator
Butées réglables limitant larotation à 90° (+/- 2°)
Adjustable mechanical endstops 90° (+/- 2°)
Débrayage volantDeclutching wheel
C
Ø15
0
Ø10
2
45°
90°
406
466
A
A
32 Positions32 location
Dou
ille
d'en
trai
nem
ent a
mov
ible
Rem
ovab
le d
rive
sock
et
64Ø
86
90 F10-F14
F12
Ø15
0
Ø12
5
45°
90°
A
Rond
elle
de
cent
rage
Cent
erin
g rin
g 385
466
3
Ø85
f8F10
DA / HA
ISO 5211F10
Vue C de la brideView C of the �ange
F10 = 4 x M10Prof./Depth: 21
A-A
DA / HA
F14 = 4 x M16Prof./Depth: 21
90°
Ø17
5
Ø14
0
ISO 5211F14
Vue B de la brideView B of the �ange
ISO 5211F12
Vue A de la brideView A of the �ange
F12 = 8 x M12Prof./Depth: 18
F12
* 3
*1
* 3
* 3
* 1
*2
Ø12
8
100
40
4
Ø10
0f8
406
466
612
308
569
114
80
* Valeur théorique à con�rmer Theoretical value to be con�rmed
STX6 + RS108
Weight / Poids54 kg
28
4 rue d’Arsonval - CS 70091 - 95505 Gonesse CEDEX FranceTel. : +33 (0)1 34 07 71 00 - Fax : +33 (0)1 34 07 71 01 - [email protected] - www.bernardcontrols.com
TEC0
2-0
7_E
+F_
GR
P_re
v05
Dim
ensi
onal
dra
win
gs /
Pla
ns d
’enc
ombr
emen
t
S
x' x
y
y'S
x' x
y
y'
x' x
y
y'd7
Parallel square / Carré Key / Alésage «DoubleD» / Méplat
SOCKET MACHININGUSINAGE DE LA DOUILLE
Socket with 48 positionsDouille avec 48 positions
Standard dimensions S Ød7 SDimensions standard 22 / 27 / 36 / 46 35 / 40 / 48 / 50 / 60 / 72 / 80 32 / 36 / 46
* Valeur théorique à con�rmer Theoretical value to be con�rmed
Dou
ille
d'en
trai
nem
ent a
mov
ible
Rem
ovab
le d
rive
sock
et
48 Positions48 location
A
A
Ø21
0
45°
Ø21
0
Ø16
5
45°
90°
406
A
103
Ø11
0
Commande localeLocal controls
RaccordementBus de terrain
(En option)Connection
Fieldbus controls(Optional)
Indicateur de positionPosition indicator
2x1"+1x1"1/2
Raccordementélectrique
Cable entries
Volant de commandemanuelle
Emergency Handwheel
Indicateur de positionPosition indicator
Butées réglables limitant larotation à 90° (+/- 2°)Adjustable mechanical endstops 90° (+/- 2°)
Rond
elle
pla
teFl
at ri
ng
Ø21
0
Ø13
0.5
4
B
Débrayage volantDeclutching wheel
A-A
F14 = 4 x M16Prof./Depth: 30
90°
Ø14
0
ISO 5210F14
Vue A de la brideView A of the �ange
F16 = 4 x M20Prof./Depth: 30
ISO 5210F16
Vue B de la brideView B of the �ange
*2
* 1
*1
* 3
* 3
* 3
405
Ø12
8
569
5
Ø13
0f8
189
406
466
755
100
40
80
466
STX6 + RS258
Weight / Poids74 kg
29
4 rue d’Arsonval - CS 70091 - 95505 Gonesse CEDEX FranceTel. : +33 (0)1 34 07 71 00 - Fax : +33 (0)1 34 07 71 01 - [email protected] - www.bernardcontrols.com
TEC0
2-0
7_E
+F_
GR
P_re
v05
Dim
ensi
onal
dra
win
gs /
Pla
ns d
’enc
ombr
emen
t
S
x' x
y
y'
x' x
y
y'd7
S
x' x
y
y'
Parallel square / Carré Key / Alésage «DoubleD» / Méplat
SOCKET MACHININGUSINAGE DE LA DOUILLE
Socket with 40 positionsDouille avec 40 positions
Standard dimensions S Ød7 SDimensions standard 27 / 36 / 46 / 50 42 / 48 / 50 / 60 / 72 / 80 36 / 46
Volant de commandemanuelle
Emergency Handwheel
Indicateur de positionPosition indicator
2x1"+1x1"1/2
RaccordementBus de terrain
(En option)Connection
Fieldbus controls(Optional)
Raccordementélectrique
Cable entriesDébrayage volant
Declutching wheel
Indicateur de positionPosition indicator
Butées réglables limitant larotation à 90° (+/- 2°)Adjustable mechanical endstops 90° (+/- 2°)
Commande localeLocal controls
A
Rond
elle
pla
teFl
at ri
ng
Dou
ille
d'en
trai
nem
ent a
mov
ible
Rem
ovab
le d
rive
sock
et
40 Positions40 location
A
A
Ø21
0
Ø13
0.5
5103
Ø11
0
Ø21
0
Ø16
5
45°
90°
F16
A-A
F16 = 4 x M20Prof./Depth: 30
ISO 5211F16
Vue A de la brideView A of the �ange
* 3
* 1
* 3
* 3
*2
80
222
360
569
Ø13
0f8
5
406
154
744
701
466
100
40
STX6G + RS438
Weight / Poids77 kg
30
4 rue d’Arsonval - CS 70091 - 95505 Gonesse CEDEX FranceTel. : +33 (0)1 34 07 71 00 - Fax : +33 (0)1 34 07 71 01 - [email protected] - www.bernardcontrols.com
TEC0
2-0
7_E
+F_
GR
P_re
v05
Dim
ensi
onal
dra
win
gs /
Pla
ns d
’enc
ombr
emen
t
S
x' x
y
y'
x' x
y
y'd7
Parallel square / Carré Key / Alésage
SOCKET MACHININGUSINAGE DE LA DOUILLE
Socket with 54 positionsDouille avec 54 positions
Standard dimensions S Ød7 Dimensions standard 46 / 50 / 55 60 / 70 / 72 / 80 / 100
Volant de commandemanuelle
Emergency Handwheel
Indicateur de positionPosition indicator
Commande localeLocal controls
2x1"+1x1"1/2
RaccordementBus de terrain
(En option)Connection
Fieldbus controls(Optional)
Raccordementélectrique
Cable entriesDébrayage volant
Declutching wheel
Indicateur de positionPosition indicator
Butées réglables limitant larotation à 90° (+/- 2°)Adjustable mechanical endstops 90° (+/- 2°)
Ø30
0
Ø25
4
22.5°
5
Ø30
0
Ø20
1Ro
ndel
le p
late
Flat
ring
Dou
ille
d'en
trai
nem
ent a
mov
ible
Rem
ovab
le d
rive
sock
et
54 Positions54 location
A
A
110
Ø14
0
A
ISO 5211F25
Vue A de la brideView A of the �ange
F25 = 8 x M16Prof./Depth: 24
A-A
* 3
* 3
* 1
*2
* 3
80
100
405
222
569
5
425
872
184
200f
8
466
829
45°
40
STX6 + RS1008G
Weight / Poids102 kg
31
4 rue d’Arsonval - CS 70091 - 95505 Gonesse CEDEX FranceTel. : +33 (0)1 34 07 71 00 - Fax : +33 (0)1 34 07 71 01 - [email protected] - www.bernardcontrols.com
TEC0
2-0
7_E
+F_
GR
P_re
v05
Dim
ensi
onal
dra
win
gs /
Pla
ns d
’enc
ombr
emen
t
S
x' x
y
y'
x' x
y
y'd7
Parallel square / Carré Key / Alésage
SOCKET MACHININGUSINAGE DE LA DOUILLE
Socket with 54 positionsDouille avec 54 positions
Standard dimensions S Ød7 Dimensions standard 46 / 50 / 55 60 / 70 / 72 / 80 / 100
Volant de commandemanuelle
Emergency Handwheel
A�cheurDisplay(Intelli+)
RaccordementBus de terrain
ConnectionFieldbus controls
RaccordementBus de terrain
ConnectionFieldbus controls
Commande localeLocal controls
Ø30
0
Ø25
4
22.5° 45°
A
Dou
ille
d'en
trai
nem
ent a
mov
ible
Rem
ovab
le d
rive
sock
et
54 Positions54 location
A
A
5
Ø30
0
Ø20
1
110
Ø14
0
Rond
elle
pla
teFl
at ri
ng
Butées réglables limitant larotation à 90° (+/- 2°)Adjustable mechanical endstops 90° (+/- 2°)
Indicateur de positionPosition indicator
ISO 5210F25
Vue A de la brideView A of the �ange
F25 = 8 x M16Prof./Depth: 24
A-A
40
613
453
40
5
100
404
Ø20
0f8
184
789
540
* 3
* 1
* 3
* 3
*2
Ø450
STX20 + RS1008
Weight / Poids113 kg
32
4 rue d’Arsonval - CS 70091 - 95505 Gonesse CEDEX FranceTel. : +33 (0)1 34 07 71 00 - Fax : +33 (0)1 34 07 71 01 - [email protected] - www.bernardcontrols.com
TEC0
2-0
7_E
+F_
GR
P_re
v05
STX20 + SBWG-04-1SM
Dim
ensi
onal
dra
win
gs /
Pla
ns d
’enc
ombr
emen
t
S
x' x
y
y'
x' x
y
y'd7
Parallel square / Carré Key / Alésage
SOCKET MACHININGUSINAGE DE LA DOUILLE
Max dimensionsDimensions Max
S66mm
Ød795mm
Weight / Poids118 kg
33
4 rue d’Arsonval - CS 70091 - 95505 Gonesse CEDEX FranceTel. : +33 (0)1 34 07 71 00 - Fax : +33 (0)1 34 07 71 01 - [email protected] - www.bernardcontrols.com
TEC0
2-0
7_E
+F_
GR
P_re
v05
STX20 + SBWG-05-1SDM
Dim
ensi
onal
dra
win
gs /
Pla
ns d
’enc
ombr
emen
t
S
x' x
y
y'
x' x
y
y'd7
Parallel square / Carré Key / Alésage
SOCKET MACHININGUSINAGE DE LA DOUILLE
Max dimensionsDimensions Max
S80mm
Ød7115mm
Weight / Poids160 kg
34
4 rue d’Arsonval - CS 70091 - 95505 Gonesse CEDEX FranceTel. : +33 (0)1 34 07 71 00 - Fax : +33 (0)1 34 07 71 01 - [email protected] - www.bernardcontrols.com
TEC0
2-0
7_E
+F_
GR
P_re
v05
STX40 + SBWG-05-1SM
Dim
ensi
onal
dra
win
gs /
Pla
ns d
’enc
ombr
emen
t
Weight / Poids166 kg
S
x' x
y
y'
x' x
y
y'd7
Parallel square / Carré Key / Alésage
SOCKET MACHININGUSINAGE DE LA DOUILLE
Max dimensionsDimensions Max
S80mm
Ød7115mm
35
4 rue d’Arsonval - CS 70091 - 95505 Gonesse CEDEX FranceTel. : +33 (0)1 34 07 71 00 - Fax : +33 (0)1 34 07 71 01 - [email protected] - www.bernardcontrols.com
TEC0
2-0
7_E
+F_
GR
P_re
v05
STX20 + SBWG-55-1SDM
Dim
ensi
onal
dra
win
gs /
Pla
ns d
’enc
ombr
emen
t
Weight / Poids190 kg
S
x' x
y
y'
x' x
y
y'd7
Parallel square / Carré Key / Alésage
SOCKET MACHININGUSINAGE DE LA DOUILLE
Max dimensionsDimensions Max
S86mm
Ød7125mm
36
4 rue d’Arsonval - CS 70091 - 95505 Gonesse CEDEX FranceTel. : +33 (0)1 34 07 71 00 - Fax : +33 (0)1 34 07 71 01 - [email protected] - www.bernardcontrols.com
TEC0
2-0
7_E
+F_
GR
P_re
v05
STX40 + SBWG-55-1SM
Dim
ensi
onal
dra
win
gs /
Pla
ns d
’enc
ombr
emen
t
Weight / Poids206 kg
S
x' x
y
y'
x' x
y
y'd7
Parallel square / Carré Key / Alésage
SOCKET MACHININGUSINAGE DE LA DOUILLE
Max dimensionsDimensions Max
S86mm
Ød7125mm
37
4 rue d’Arsonval - CS 70091 - 95505 Gonesse CEDEX FranceTel. : +33 (0)1 34 07 71 00 - Fax : +33 (0)1 34 07 71 01 - [email protected] - www.bernardcontrols.com
TEC0
2-0
7_E
+F_
GR
P_re
v05
STX20 + SBWG-06-1SDM
Dim
ensi
onal
dra
win
gs /
Pla
ns d
’enc
ombr
emen
t
Weight / Poids250 kg
S
x' x
y
y'
x' x
y
y'd7
Parallel square / Carré Key / Alésage
SOCKET MACHININGUSINAGE DE LA DOUILLE
Max dimensionsDimensions Max
S96mm
Ød7140mm
38
4 rue d’Arsonval - CS 70091 - 95505 Gonesse CEDEX FranceTel. : +33 (0)1 34 07 71 00 - Fax : +33 (0)1 34 07 71 01 - [email protected] - www.bernardcontrols.com
TEC0
2-0
7_E
+F_
GR
P_re
v05
STX40 + SBWG-06-1SBM
Dim
ensi
onal
dra
win
gs /
Pla
ns d
’enc
ombr
emen
t
Weight / Poids266 kg
S
x' x
y
y'
x' x
y
y'd7
Parallel square / Carré Key / Alésage
SOCKET MACHININGUSINAGE DE LA DOUILLE
Max dimensionsDimensions Max
S96mm
Ød7140mm
39
4 rue d’Arsonval - CS 70091 - 95505 Gonesse CEDEX FranceTel. : +33 (0)1 34 07 71 00 - Fax : +33 (0)1 34 07 71 01 - [email protected] - www.bernardcontrols.com
TEC0
2-0
7_E
+F_
GR
P_re
v05
STX20 + SBWG-07-1SDM
Dim
ensi
onal
dra
win
gs /
Pla
ns d
’enc
ombr
emen
t
Weight / Poids356 kg
S
x' x
y
y'
x' x
y
y'd7
Parallel square / Carré Key / Alésage
SOCKET MACHININGUSINAGE DE LA DOUILLE
Max dimensionsDimensions Max
S126mm
Ød7180mm
40
4 rue d’Arsonval - CS 70091 - 95505 Gonesse CEDEX FranceTel. : +33 (0)1 34 07 71 00 - Fax : +33 (0)1 34 07 71 01 - [email protected] - www.bernardcontrols.com
TEC0
2-0
7_E
+F_
GR
P_re
v05
STX61 + SBWG07.1SBM
Dim
ensi
onal
dra
win
gs /
Pla
ns d
’enc
ombr
emen
t
Weight / Poids384 kg
S
x' x
y
y'
x' x
y
y'd7
Parallel square / Carré Key / Alésage
SOCKET MACHININGUSINAGE DE LA DOUILLE
Max dimensionsDimensions Max
S126mm
Ød7180mm
41
4 rue d’Arsonval - CS 70091 - 95505 Gonesse CEDEX FranceTel. : +33 (0)1 34 07 71 00 - Fax : +33 (0)1 34 07 71 01 - [email protected] - www.bernardcontrols.com
TEC0
2-0
7_E
+F_
GR
P_re
v05
STX40 + SBWG75.1SBM
Dim
ensi
onal
dra
win
gs /
Pla
ns d
’enc
ombr
emen
t
Weight / Poids514 kg
S
x' x
y
y'
x' x
y
y'd7
Parallel square / Carré Key / Alésage
SOCKET MACHININGUSINAGE DE LA DOUILLE
Max dimensionsDimensions Max
S146mm
Ød7210mm
42
4 rue d’Arsonval - CS 70091 - 95505 Gonesse CEDEX FranceTel. : +33 (0)1 34 07 71 00 - Fax : +33 (0)1 34 07 71 01 - [email protected] - www.bernardcontrols.com
TEC0
2-0
7_E
+F_
GR
P_re
v05
STX61 + SBWG75.1SBM
Dim
ensi
onal
dra
win
gs /
Pla
ns d
’enc
ombr
emen
t
Weight / Poids527 kg
S
x' x
y
y'
x' x
y
y'd7
Parallel square / Carré Key / Alésage
SOCKET MACHININGUSINAGE DE LA DOUILLE
Max dimensionsDimensions Max
S146mm
Ød7210mm
43
4 rue d’Arsonval - CS 70091 - 95505 Gonesse CEDEX FranceTel. : +33 (0)1 34 07 71 00 - Fax : +33 (0)1 34 07 71 01 - [email protected] - www.bernardcontrols.com
TEC0
2-0
7_E
+F_
GR
P_re
v05
STX40 + SBWG-08-1SDM
Dim
ensi
onal
dra
win
gs /
Pla
ns d
’enc
ombr
emen
t
Weight / Poids628 kg
S
x' x
y
y'
x' x
y
y'd7
Parallel square / Carré Key / Alésage
SOCKET MACHININGUSINAGE DE LA DOUILLE
Max dimensionsDimensions Max
S155mm
Ød7225mm
Wiring diagrams Schémas de câblage
All
data
in t
his
broc
hure
are
giv
en fo
r inf
orm
atio
n on
ly a
nd a
re s
ubje
ct t
o ch
ange
with
out
notic
e.Le
s do
nnée
s co
nten
ues
dans
cet
te b
roch
ure
sont
don
nées
pou
r inf
orm
atio
n et
peu
vent
êtr
e m
odifi
ées
sans
pré
avis
.
Technical handbook - Guide technique
SQX & Combi INTELLI+®
Servomoteurs Quart-de-tour Antidéflagrants
SQX & Combi INTELLI+®
Explosionproof Quarter-turn Actuators
45
4 rue d’Arsonval - CS 70091 - 95505 Gonesse CEDEX FranceTel. : +33 (0)1 34 07 71 00 - Fax : +33 (0)1 34 07 71 01 - [email protected] - www.bernardcontrols.com
TEC0
2-0
7_E
+F_
GR
P_re
v05
Wir
ing
diag
ram
s /
Sché
mas
de
câbl
age
*160
- 25
0V o
n re
ques
t*1
60 -
250V
sur
dem
ande
INTELLI+®
46
4 rue d’Arsonval - CS 70091 - 95505 Gonesse CEDEX FranceTel. : +33 (0)1 34 07 71 00 - Fax : +33 (0)1 34 07 71 01 - [email protected] - www.bernardcontrols.com
TEC0
2-0
7_E
+F_
GR
P_re
v05
Wir
ing
diag
ram
s /
Sché
mas
de
câbl
age
*160
- 25
0V o
n re
ques
t*1
60 -
250V
sur
dem
ande
INTELLI+® POSITION TRANSMITTER
47
4 rue d’Arsonval - CS 70091 - 95505 Gonesse CEDEX FranceTel. : +33 (0)1 34 07 71 00 - Fax : +33 (0)1 34 07 71 01 - [email protected] - www.bernardcontrols.com
TEC0
2-0
7_E
+F_
GR
P_re
v05
Wir
ing
diag
ram
s /
Sché
mas
de
câbl
age
*160
- 25
0V o
n re
ques
t*1
60 -
250V
sur
dem
ande
INTELLI+® POSITIONER
48
4 rue d’Arsonval - CS 70091 - 95505 Gonesse CEDEX FranceTel. : +33 (0)1 34 07 71 00 - Fax : +33 (0)1 34 07 71 01 - [email protected] - www.bernardcontrols.com
TEC0
2-0
7_E
+F_
GR
P_re
v05
*160
- 25
0V o
n re
ques
t*1
60 -
250V
sur
dem
ande
INTELLI+® PROFIBUS DPV1
Wir
ing
diag
ram
s /
Sché
mas
de
câbl
age
49
4 rue d’Arsonval - CS 70091 - 95505 Gonesse CEDEX FranceTel. : +33 (0)1 34 07 71 00 - Fax : +33 (0)1 34 07 71 01 - [email protected] - www.bernardcontrols.com
TEC0
2-0
7_E
+F_
GR
P_re
v05
Wir
ing
diag
ram
s /
Sché
mas
de
câbl
age
*160
- 25
0V o
n re
ques
t*1
60 -
250V
sur
dem
ande
INTELLI+® PROFIBUS DPV1 REDUNDANT
50
4 rue d’Arsonval - CS 70091 - 95505 Gonesse CEDEX FranceTel. : +33 (0)1 34 07 71 00 - Fax : +33 (0)1 34 07 71 01 - [email protected] - www.bernardcontrols.com
TEC0
2-0
7_E
+F_
GR
P_re
v05
Wir
ing
diag
ram
s /
Sché
mas
de
câbl
age
*160
- 25
0V o
n re
ques
t*1
60 -
250V
sur
dem
ande
INTELLI+® FOUNDATION FIELDBUS
Wir
ing
diag
ram
s /
Sché
mas
de
câbl
age
51
4 rue d’Arsonval - CS 70091 - 95505 Gonesse CEDEX FranceTel. : +33 (0)1 34 07 71 00 - Fax : +33 (0)1 34 07 71 01 - [email protected] - www.bernardcontrols.com
TEC0
2-0
7_E
+F_
GR
P_re
v05
Wir
ing
diag
ram
s /
Sché
mas
de
câbl
age
*160
- 25
0V o
n re
ques
t*1
60 -
250V
sur
dem
ande
INTELLI+® MODBUS
Wir
ing
diag
ram
s /
Sché
mas
de
câbl
age
52
4 rue d’Arsonval - CS 70091 - 95505 Gonesse CEDEX FranceTel. : +33 (0)1 34 07 71 00 - Fax : +33 (0)1 34 07 71 01 - [email protected] - www.bernardcontrols.com
TEC0
2-0
7_E
+F_
GR
P_re
v05
Wir
ing
diag
ram
s /
Sché
mas
de
câbl
age
RevB
SIL2* INTELLI+® (ESD & SIGNALING)
* Important : Le servomoteur certifié SIL est disponible en alimentation triphasée et propose des caractéristiques de fonctionnement différentes. Merci de consulter ces spécificités techniques dans le catalogue dédié : ‘Servomoteurs SIL’
* Important : SIL certified actuator is available with a three phase power supply and have diffrent features. Please check the technical specifications in the dedicated catalogue : ‘SIL Actuators’
53
4 rue d’Arsonval - CS 70091 - 95505 Gonesse CEDEX FranceTel. : +33 (0)1 34 07 71 00 - Fax : +33 (0)1 34 07 71 01 - [email protected] - www.bernardcontrols.com
TEC0
2-0
7_E
+F_
GR
P_re
v05
Wir
ing
diag
ram
s /
Sché
mas
de
câbl
age
* Important : Le servomoteur certifié SIL est disponible en alimentation triphasée et propose des caractéristiques de fonctionnement différentes. Merci de consulter ces spécificités techniques dans le catalogue dédié : ‘Servomoteurs SIL’
* Important : SIL certified actuator is available with a three phase power supply and have diffrent features. Please check the technical specifications in the dedicated catalogue : ‘SIL Actuators’
RevB
SIL2* INTELLI+® & PROFIBUS DPV1
54
4 rue d’Arsonval - CS 70091 - 95505 Gonesse CEDEX FranceTel. : +33 (0)1 34 07 71 00 - Fax : +33 (0)1 34 07 71 01 - [email protected] - www.bernardcontrols.com
TEC0
2-0
7_E
+F_
GR
P_re
v05
NOTES
Not
es
55
4 rue d’Arsonval - CS 70091 - 95505 Gonesse CEDEX FranceTel. : +33 (0)1 34 07 71 00 - Fax : +33 (0)1 34 07 71 01 - [email protected] - www.bernardcontrols.com
TEC0
2-0
7_E
+F_
GR
P_re
v05
NOTES
Not
es
Invest in Confidence
TEC
02
-07_
E+F_
GR
P_r
ev0
5
All
data
in t
his
bro
chu
re a
re g
iven
for
info
rmat
ion
on
ly a
nd
are
subj
ect
to c
han
ge w
ith
out
not
ice.
Les
don
née
s co
nte
nu
es d
ans
cett
e br
och
ure
son
t do
nn
ées
pou
r in
form
atio
n e
t pe
uve
nt
être
m
odifi
ées
san
s pr
éavi
s.
B E R N A R D C O N T R O L S G R O U PCORPORATE HEADQUARTERS4 rue d’Arsonval - CS 70091 / 95505 Gonesse CEDEX France / Tel. : +33 (0)1 34 07 71 00 / Fax : +33 (0)1 34 07 71 01 / [email protected]
CONTACT BY OPERATING AREAS
>AMERICA (NORTH)
UNITED STATESBERNARD CONTROLS UNITED STATES [email protected]
Tel. +1 281 578 66 66
>ASIA
CHINABERNARD CONTROLS [email protected]
Tel. +86 (0) 10 6789 2861
KOREABERNARD CONTROLS [email protected]
Tel. +82 2 553 6957
SINGAPOREBERNARD CONTROLS [email protected]
Tel. +65 65 654 227
>EUROPEGERMANYBERNARD CONTROLS [email protected]. +49 2241 9834 0
BELGIUMBERNARD CONTROLS BENELUXBRUSSELSinquiry.belgium@[email protected]. +32 (0)2 343 41 22
FRANCEBERNARD CONTROLS FRANCEGONESSE (PARIS)[email protected]. +33 (0)1 34 07 71 00
ITALYBERNARD CONTROLS [email protected]. +39 02 931 85 233
SPAINBERNARD CONTROLS [email protected]. +34 91 30 41 139
>DEVELOPPEMENTAFRICABERNARD CONTROLS [email protected]. +33 (0)1 34 07 71 00
MIDDLE EASTBERNARD CONTROLS MIDDLE-EASTDUBAI - [email protected]. +971 4 880 0660
CHENNAI - [email protected]. +971 4 880 0660
RUSSIABERNARD CONTROLS [email protected]. +33 (0)1 34 07 71 00
SOUTH AMERICABERNARD CONTROLS SOUTH [email protected]. +33 (0)1 34 07 71 00
More than 50 agents and distributors worldwide. Contact details on www.bernardcontrols.com