Note: The DSL light may blink.

Note: If the Ethernet Light does NOT turn green, make sure the Yellow Cable isproperly connected on both ends.

1 Connect the Modem to a Computer

Step1 Get the Wireless DSLModem from your DSL QuickStart Kit and take it out of the bag.

Step4 Plug the larger end of thePower Cord into a Power Outlet.

Step6 Make sure the Power Light onthe Modem is SOLID Green.

Step5 Make sure the Power Switchis ON.

Step7 Get the Yellow Cable.

Step8 Plug one end of the YellowCable into any of the Yellow Ports onthe back of the Wireless DSL Modem.

Flip this Quick Start Guide over to continue NEXT

PowerOutlet

PowerCord

Step10 Make sure that 1 of the 4Ethernet lights on the Modem isGreen. This may take a few moments.

Yellow Port

YellowCable

Step11 Get the Black orGray PhoneCable from your DSL Quick Start Kit.

Step12 Plug one end of the PhoneCable into the Gray Po rt located onthe back of the Modem.

Step9 Make sure that yourcomputer is turned on. Then, plugthe other end of the Yellow Cableinto the Ethernet Port on theback of the computer.

An Ethernet Port looks similar toa regular Phone Jack, but is slightly larger.

Step13 Plug the other end of thePhone Cable into the Phone Jackclosest to your computer.

Gray PortGray

Cable

example of a typical inlinephone filter

PhonePort

Gray Cable

Step14 Make sure All DevicesExcept This DSL Modemwith the samephone number as your DSL Line havePhone Filters. This includes telephones,fax machines, caller ID boxes, satelliteTV receivers, TiVo devices, and answering machines.

Note: Your Power Cord may look different.

Step2 Get the Power Cordfrom your DSL Quick Start Kit.

Step3 Plug the smaller end ofthe Power Cord into the Black

Port on the back of the Modem.Power Cord

BlackPort

Note: If the DSL Light continues to blink, make sure you received notificationfrom your DSL Internet Service Provider that your DSL service has been activated.

Note: Do NOT put a phone filter on the modem!

Step15 Make sure that the Powerand DSL Lights are solid Green. Thismay take up to 30 seconds.

2 Configure the Modem for AT&T

Step1 Open a Web browser(Netscape Navigator or InternetExplorer, for example). In the addressbar, enter http://192.168.0.1then press Enter on the keyboard.

Step2 The “Main Menu” screenappears. Select If you are an AT&Tcustomer Click Here .

Step3 The “Welcome”screenappears. Click Next.

Note: If this screen does not appear, make sure your Ethernet port is configuredfor Dynamic IP.

Note: When you open your web browser you may get a page cannot be displayederror. This is normal and will not effect the instructions in step 1.

Step4 The Modem is now connecting to AT&T. This processcan take up to 3 minutes.

Step5 Follow the AT&T onlineinstruction to complete setting upthe Modem.

Step6 If this browser windowappears, write down the "MemberID" and "Password".

Member ID

Password

Step7 Open a new browserwindow. In the address bar of thisnew window, enter http://192.168.0.1then press Enter on the keyboard.

Step8 The "Quicksetup" screenappears. Enter the Member ID andthe password you wrote down instep 6 in the "PPP User Name"and "PPP Password" text boxes.Then click Apply.

Step9 Wait 2 minutes and return to the AT&T window andcomplete the AT&T installation process.

If you have any problems connecting or configuring this device please contact our Tech Support at

1-888-436-0657

Part No: 0530-0652-000 QS1144/1110

For all other DSL Services skip to Section 3

GT784WN QS7_GT704WG QS7.qxd 12/14/10 12:13 PM Page 1

Quick Start Guide

Connect the Modem to a Computer

Configure the Modem for AT&T

Configure the Modem for All OtherService Providers

Configure Wireless Connection & Security

3

2

1

4

Note: Compatible with Macintosh, Linux and Windows.

This Quick Start Guide will walk you through theeasy steps to set up your Wireless DSL Modem.During this process, we’ll show you how to:

You will need the following items from your Actiontec Quick Start Kit:

You will also need to know your DSL Username and Password provided by your Internet Service Provider.

• Wireless DSL Modem

• Black Power Cord

• Black or Gray Phone Cable• Yellow Cable

NEXT

WirelessDSL Modem

Model# GT784WN

3 Configure the Modem for All Other Service Providers

Step1 Open a Web browser(Netscape Navigator or InternetExplorer, for example). In the addressbar, enter http://192.168.0.1then press Enter on the keyboard.

Step2 The “Main Menu” screenappears. Select All other ServiceProviders Click Here for AutoDetection.

Step3 The “Welcome”screenappears. Click Next.

Step4 The Modem is nowdetecting your Internet provider’ssettings. This process can take upto 3 minutes.

Note: If this screen does not appear, make sure your Ethernet port is configuredfor Dynamic IP.

Congratulations!

You have successfully installed your DSL Modem. You can now access the Internet.

Step5 In the next window, enteryour primary User Name andPassword provided by your ISP.Click Next.

Note: When you open your web browser you may get a page cannot be displayederror. This is normal and will not effect the instructions in step 1.

Hint: Your Username may be your main e-mail address. If you have any problems connecting or configuring this device please contact our Tech Support at

1-888-436-0657

Service provider phone numbers

AOL 888-418-5320

AT&T 877-722-3755

AT&T/BellSouth 888-321-2375

Century Tel 800-809-1410

Covad DSL 888-642-6823

Earthlink 888-829-8466

Embarq 888-723-8010

Iowa Telecom 877-901-4692

MSN 877-327-6744

Qwest 800-247-7285

SureWest 888-639-1611

TDS DSL Support 866-571-6662

US Family 800-300-4256

Verizon 800-567-6789

© 2010 Actiontec Electronics, Inc. Actiontec, Actiontec Installation Buddy, Creative Solutionsfor the Digital Life, and the Actiontec logo are registered trademarks or trademarks ofActiontec Electronics, Inc. Incorporated in the U.S. or other countries. All other names areproperties of their respective owners. Product photo may differ from actual product, however functionality remains as stated above.Specifications are subject to change without notice

4 Configure Wireless Connection and Security

Step1 Click the YES button.

Step2 Select a name for yourwireless network and enter it inthe“ESSID” field. Then click NEXTto continue.

Step4 Select the type of wirelesssecurity that you want to use.Actiontec recommends usingWPA&WPA2. The following stepswill show you how to enableWPA&WPA2 wireless security.

Step5 Enter in a password orpre-shared key. The key must beat least 8 characters long. ClickNEXT to continue.

Step6 The “Congratulations”screen appears. The DSL Light willglow SOLID Green and the InternetLight will flicker Green indicatingInternet activity.

Step3 It is recommended thatyou secure your wireless networkby clicking Yes. If you choose notto secure your network, click Noand you will have completed theinstallation.

Note: All of your other wireless devices will need to support that same type of wireless security chosen in order to connect to your wireless network..

Note: The Wireless Wizard can also be run from the Wireless Basic Setup page ofthe Modem’s GUI.

GT784WN QS7_GT704WG QS7.qxd 12/14/10 12:13 PM Page 2