8
QuikStart Installation Guide This is an abbreviated Installation Manual, addressing wiring and programming of the GT Series. The complete GT Series Installation Manual is located on the CD supplied with the GT-BC Bus Control Unit. Access the PDF file from the CD and print the entire manual if a hard copy is needed. If installing a digital entry system, the program for loading names and numbers for each tenant is also located on the CD. ATTENTION: GT SERIES Multi-Tenant Entry Security How-To Video Link Installation Videos

GT SERIES - Aiphone

Embed Size (px)

Citation preview

Page 1: GT SERIES - Aiphone

QuikStart Installation Guide

This is an abbreviated Installation Manual, addressing wiring and programming of the GT Series. The complete GT Series Installation Manual is located on the CD supplied with the GT-BC Bus Control

Unit. Access the PDF file from the CD and print the entire manual if a hard copy is needed. If installing a digital entry system, the program for loading names and numbers for each tenant is also located on the CD.

ATTENTION:

GT SERIESMulti-Tenant Entry Security

How-To

Video Link

Installation Videos

Page 2: GT SERIES - Aiphone

*DP

GT-1A

4-15/16" 1-1/4"

6-7/

8"

GT-1A

4-15/16" 1-1/4"6-

7/8"

GT-1A

4-15/16" 1-1/4"

6-7/

8"

GT-1A

4-15/16" 1-1/4"

6-7/

8"

GT-1A

4-15/16" 1-1/4"

6-7/

8"

GT-1A

4-15/16" 1-1/4"

6-7/

8"

GT-1A

4-15/16" 1-1/4"

6-7/

8"

GT-1A

4-15/16" 1-1/4"

6-7/

8"

GT-1A

4-15/16" 1-1/4"

6-7/

8"

GT-1A

4-15/16" 1-1/4"6-

7/8"

GT-1A

4-15/16" 1-1/4"

6-7/

8"

GT-1A

4-15/16" 1-1/4"

6-7/

8"

CN2

CN2

CN2CN1

CN1

CN1

PS-2420UL

GT-BCGT-VBC

PS-2420UL PS-2420UL

1P

1P1P

1P x 2

1P x 2

1P x 2

1P x 2

1P x 2

1P x 2

1P x 2

1P

1P x 2

1P x 2

1P x 21P x 2

GT-4Z

GT-4Z

Doorbell

1P

GFK-PS

GT-1C

GT-1C

1P x 2

1P x 2

Trunk Line No. 1Homerun usingGT-4Z (max. 6)

Trunk Line No. 2Loop wiring(max. 25)

Trunk LineNo. 3-6

GT-MK w/GFW-S

GT-MK w/GFW-S

Security Guard/Concierge Stations (max. 2)Entrance Stations (max. 5)

NOTE: Do not mix loop andhomerun wiring methodson the same trunk.

GT Standard Configuration Sample

R1R2

+-

+-

R1 R2R1 R2GTA-DES

5-5/16"

12-5

/8"

1-3/4"1/2"

CN2

CN1

CN3

CN100

+-

+-

ELCELM

ELBPT

MagLock

ELCELM

ELBPT

R1 R2IN

R1 R2OUT

R1 R2IN

R1 R2OUT

R1 R2IN

R1 R2OUT

R1 R2IN

R1 R2OUT

R1 R2IN

R1 R2OUT

R1 R2IN

R1 R2OUT

R1 R2IN

R1 R2OUT

R1 R2IN

R1 R2OUT

R1 R2IN

R1 R2OUT

R1 R2IN

R1 R2OUT

R1 R2IN

R1 R2OUT

R1 R2IN

R1 R2OUT

PS24

PS24

GT-BC

Loop Wiring Method Max. of 25 stations per loop / trunk

Homerun Wiring Method

*Distribution Point: NOT provided by Aiphone. This can be any device that parallels or commons the R1 / R2 connection. (Terminal strip, punch down block, wire nuts, etc.)

Tenant stations shown are the GT-1A. The GT-1D tenant stations can also be used and wire in the same manner.

2 | GT Series QuikStart Guide

DoorStrike

SYSTEM WIRING: AUDIO ONLY DIRECT SELECT & DIGITAL DISPLAY ENTRANCE STATIONS

R1

R1

R2

R2

Max. wire distance from distribution point to any tenant is 980’. Max. cumulative wire distance is 8200’.Refer to page 9 of the GT Series Installation Manual for complete wire distance information.

WIRE TYPE

87200220AWG 2 Cond.Solid Non ShieldedPE Insulated

87180218AWG 2 Cond.Solid Non ShieldedPE Insulated

POWERPS24PS-2420UL

PTPower Transformer (Use proper power for the Strike or Mag Lock being used).

Page 3: GT SERIES - Aiphone

*DP

16-1

/8"

2-11/16"5-7/8"

GT-DM

CN2

CN1

CN3

CN100

CN3

CN1

16-3

/4"

5-5/16" 1-3/4"1/2"

GTV-DES104

ELCELM

ELBPT

R1R2

+-

+-

PS24

+-

ELCELM

ELBPT

A1 A2R1 R2A1A2

PS-2420UL

GT-BCGT-VBC

PS-2420UL PS-2420UL

1P

1P1P

1P x 2

1P x 2

1P x 2

1P x 2

1P x 2

1P x 2

1P x 2

1P

1P x 2

1P x 2

1P x 21P x 2

GT-4Z

GT-4Z

Doorbell

1P

GFK-PS

GT-1C

GT-1C

1P x 2

1P x 2

Trunk Line No. 1Homerun usingGT-4Z (max. 6)

Trunk Line No. 2Loop wiring(max. 25)

Trunk LineNo. 3-6

GT-MK w/GFW-S

GT-MK w/GFW-S

Security Guard/Concierge Stations (max. 2)Entrance Stations (max. 5)

NOTE: Do not mix loop andhomerun wiring methodson the same trunk.

GT Standard Configuration Sample

R1R2

+-

+-

PS24

GT-BC

+- A1 A2 A1 A2 A1 A2 A1 A2 A1 A2

B1 B2 B1 B2 B1 B2 B1 B2 B1 B2 B1 B2

GT-1C, GT-1CB, GT-1CS

5-1/

2"

7-1/2" 1-3/16"

GT-1C, GT-1CB, GT-1CS

5-1/

2"

7-1/2" 1-3/16"B1 B2 R1 R2

B1 B2 R1 R2

GT-1C, GT-1CB, GT-1CS

5-1/

2"

7-1/2" 1-3/16"B1 B2 R1 R2

B1 B2 R1 R2

GT-1C, GT-1CB, GT-1CS5-

1/2"

7-1/2" 1-3/16"B1 B2 R1 R2

B1 B2 R1 R2

GT-1C, GT-1CB, GT-1CS

5-1/

2"

7-1/2" 1-3/16"B1 B2 R1 R2

B1 B2 R1 R2

Max. of 25 stations per loop. SW1 switch must be set to A on last monitor in the wire loop.

SW1A B

SW1A B

SW1A B

SW1A B

B1 B2 R1 R2

B1 B2 R1 R2 B1 B2 R1 R2

B1 B2 R1 R2

B1 B2 R1 R2

B1 B2 R1 R2B1 B2 R1 R2

B1 B2 R1 R2

SW1A B

SW1A B

SW1A B

SW1A B

SW1A B

SW1A B

SW1A B

SW1A B

Max. of 6 GT-4Zs per loop. SW1 switch must be set to A on last GT-4Z in the wire loop. Each tenant station homeruns to a GT-4Z and its SW1 switch must be set to A.

GT-VBC

B1 B2 R1 R2 B1 B2 R1 R2

B1 B2 R1 R2 B1 B2 R1 R2 B1 B2 R1 R2

R1 R2B1 B2OUT (1) OUT (2)

OUT (3) OUT (4)

IN

LINE OUT

SW1

A

B

GT-4Z

B1 B2 R1 R2 B1 B2 R1 R2

B1 B2 R1 R2 B1 B2 R1 R2 B1 B2 R1 R2

R1 R2B1 B2OUT (1) OUT (2)

OUT (3) OUT (4)

IN

LINE OUT

SW1

A

B

GT-4Z

IN

OUT

IN

OUT

IN

OUT

IN

OUT

IN

IN

IN

IN

IN

IN

IN

IN

Loop Wiring Method Homerun Wiring Method

3

*Distribution Point: NOT provided by Aiphone. This can be any device that parallels or commons the R1 / R2 connection. (Terminal strip, punch down block, wire nuts, etc.)

Tenant stations shown are the GT-1C. The GT-2C or GT-1M-L tenant stations can also be used and wire in the same manner.

Note: GT-2C requires a separate PS-2420UL power supply.

MagLock

DoorStrike

SYSTEM WIRING: AUDIO / VIDEO ALL-IN-ONE & DIGITAL ENTRANCE STATIONS

R1

R1

R2

R2

GT-1C, GT-1CB, GT-1CS

5-1/

2"

7-1/2" 1-3/16"

GT-1C, GT-1CB, GT-1CS5-

1/2"

7-1/2" 1-3/16"

GT-1C, GT-1CB, GT-1CS

5-1/

2"

7-1/2" 1-3/16"

GT-1C, GT-1CB, GT-1CS

5-1/

2"

7-1/2" 1-3/16"

GT-1C, GT-1CB, GT-1CS

5-1/

2"

7-1/2" 1-3/16"

GT-1C, GT-1CB, GT-1CS

5-1/

2"

7-1/2" 1-3/16"

GT-1C, GT-1CB, GT-1CS

5-1/

2"

7-1/2" 1-3/16"

Page 4: GT SERIES - Aiphone

4 | GT Series QuikStart Guide

A1A2A1A2A1A2A1A2A1A2A1A2A1A2A1A2

B1B2B1B2

B1B2B1B2

CO

MM

ON

1

SU

B 1

SU

B 2

A1A2

A1A2

~C

OM

MO

N 2

CN2

+-

CO

MM

ON

1

R1R2

R1R2

~C

OM

MO

N 2

CN1

R1R2

R1R2

~

R1R2

SU

B 1

A

R1R2

R1R2

~

SU

B 1

B

R1R2

R1R2

~

SU

B 2

A

R1R2

R1R2

~

SU

B 2

B

R1R2

R1R2

~

GTW

-LCUS

B

GT-VBX

GT-BCX

A1A2

A1A2

A1A2

A1A2

A1A2

A1A2

A1A2

A1A2

*DP

R1R2

R1R2

R1R2

R1R2

R1R2

R1R2

R1R2

R1R2

ON

1 2 3 4

ON

1 2 3 4

ON

1 2 3 4

ON

1 2 3 4

ON

1 2 3 4

ON

1 2 3 4

ON

1 2 3 4

ON

1 2 3 4

#1 #5#3 #7#2 #6#4 #8

R1R2

R1R2+-

IN

OUTGT-MK

R1R2

R1R2+-

IN

OUT

GT-MK

+-

PS24ON

1 2 3 4

#2ON

1 2 3 4

#1

+-

PS24

Connection for video entrance modules 9-16{

{Connection for audio entrance modules 9-16

R1R2

+-

GT-BC+-

PS24

+ -

A1A2

A1A2A1A2A1A2A1A2

B1B2

B1B2

B1B2

B1B2B1B2B1B2

+ -

EXP STD

+ -

R1R2

*DP

PS24

GT-BC

Video outputs to tenant stations and / or GT-4Z units. Max. of 25 tenants per trunk and 125 total tenants per GT-VBC.

Audio output to tenant stations and / or GT-4Z units. Max. of 25 tenants per trunk and 125 total tenants per GT-BC.

GT-

VAG

T-D

ASYSTEM WIRING: EXPANDED SYSTEM

OPTION CONNECTOR: TENANT STATIONS

GT-VBC

KKERYRYSWSWS1S1ES2S2ES3S3E

V+V-

Emergency alarm(Brown)

(Brown)

(Red)

(Red)

Ext. Signaling (GT-RY)(Blue)

(Orange)

(White)

(Yellow)

Video out

Display transfer Option contact output(Gray)

(Black)

Security/Utility input 1 (Orange)(Black)

Security/Utility input 2 (Yellow)(Black)

Security/Utility input 3 (Purple)(Black)

12-pin option connector 4-pin option connector(not included)

DCDCRYRYSWSW

Doctor call (Automatic entry)(Yellow)(Orange)

External Signaling (GT-RY)(Blue)(White)

Option contact output (Gray)(Black)

Option connector

DCDCRYRYSWSW

Doctor call (Automatic entry)(Yellow)(Orange)

External Signaling (GT-RY)(Blue)(White)

Option contact output (Gray)(Black)

Option connectorGT-1A

4-15/16" 1-1/4"

6-7/

8"

GT-2C

GT-1A

GT-1C

Only the option connectors for the GT-2C, GT-1C, and GT-1A are shown here. For information on other tenant station option connectors and for technical specifications for each connection, refer to pages 30-31 of the GT Series Installation Manual.

*Distribution Point: NOT provided by Aiphone. This can be any device that parallels or commons the R1 / R2 connection. (Terminal strip, punch down block, wire nuts, etc.)

KKERYRYSWSWS1S1ES2S2ES3S3E

V+V-

Emergency alarm(Brown)

(Brown)

(Red)

(Red)

Ext. Signaling (GT-RY)(Blue)

(Orange)

(White)

(Yellow)

Video out

Display transfer Option contact output(Gray)

(Black)

Security/Utility input 1 (Orange)(Black)

Security/Utility input 2 (Yellow)(Black)

Security/Utility input 3 (Purple)(Black)

12-pin option connector 4-pin option connector(not included) GT-1C, GT-1CB, GT-1CS

5-1/

2"

7-1/2" 1-3/16"

Page 5: GT SERIES - Aiphone

5

DIP SWITCH SETTINGS: ENTRANCE STATION (REQUIRED)

DIP SWITCH SETTINGS: ENTRANCE STATION (OPTIONAL)

Entrance ID Setting:Use SW2 on the GT-DA-L module or SW1 on the GT-DM entrance station to set the ID settings for each entry panel. Only switches 2, 3, & 4 are used for this setting.

ON

1 2 3 4

ON

1 2 3 4

ON

1 2 3 4

ON

1 2 3 4

ON

1 2 3 4

ON

1 2 3 4

ON

1 2 3 4

ON

1 2 3 4

ON

1 2 3 4

ON

1 2 3 4

#1 #5#3 #7#2 #6#4 #8

Guidance Language Setting:The guidance is set to off (No Guidance) when shipped. Use SW3 on the GT-DA-L module to set the appropriate language. Only switches 2, 3, & 4 are used for this setting.

ON

1 2 3 4

ON

1 2 3 4

ON

1 2 3 4

ON

1 2 3 4

ON

1 2 3 4

ON

1 2 3 4

ON

1 2 3 4

No Guidance English German DutchFrench Spanish Italian

Message Setting:Use switch 3 of SW1 on the GT-NS module to select between greeting message or operation message on the display. Default is “Greeting Message.”

Room Number Display:Use switch 2 of SW1 on the GT-NS module to choose between displaying only resident name or displaying resident name and number. Default is “Display resident name and number.”

GT-DA-L

16-1

/8"

2-11/16"5-7/8"

GT-DMGT-DA-L GT-DM

GT-NS

GT-NS

3

2

Operation Message

Display only resident name

Greeting Message

Display resident name and number

NOTE:When using the GT-DM, the settings listed below will be done via the keypad / display while in programming mode. Refer to the GT Series Installation Manual (pages 43 - 49) for set-up instructions.

ON

1 2 3 4

Entrance Monitoring:Use switch 1 of SW2 on the GT-DA-L module to enable / disable entrance monitoring. Default is “Monitoring not possible.” Enabling will allow tenants (video tenants only) to ‘call up’ the entrance station and monitor the door area.

1

Monitoring possibleMonitoring not possible

GT-DA-L

Camera View:Use switches 3 & 4 of SW1 on the GT-VA module to set the camera view. The default setting is Zoom.Zoom 3s>>Wide: Image starts zoomed and after 3 seconds goes wide.Wide 3s>>Zoom: Image starts wide and after 3 seconds zooms.

GT-VA

ON

1 2 3 4

ON

1 2 3 4

ON

1 2 3 4

ON

1 2 3 4

ZOOM WIDE ZOOM 3s>>WIDE WIDE 3s>>ZOOM

(default)

(default)

Page 6: GT SERIES - Aiphone

6 | GT Series QuikStart Guide

PROGRAMMING: INPUT RESIDENT INFORMATION

NOTE:The GT digital panel, GT-DM, and GT-MK must be programmed with the resident information before tenant stations can be addressed. The resident information can be entered using the keypad or by using the software supplied on the CD.

Direct Select / Push Button Entrance Station AddressingStep 1: Remove front cover from entrance station.Step 2: To enter programming mode, use a small screwdriver to push and release button under the

rubber cap on front of speaker module (GT-DA-L). The amber LED will begin flashing, then remain lit. Once lit, the entry panel is in programming mode.

Step 3: At tenant station, push and release the TALK button or pick up the handset to establish communication with the entrance station in programming mode.

Step 4: Push and release the desired Call Button on the entrance station to assign the button to the tenant station that is active. A blip tone will be heard.

Step 5: Turn off or hang up tenant station (GT-1A: Push TALK again, GT-1C / GT-2C: Push OFF).Step 6: Repeat steps 3-5 for remaining tenant stations.Step 7: To exit programming, push the button under the rubber cap on the GT-DA-L module again

and the amber LED will turn off. The system is now ready for use.

PROGRAMMING: ADDRESSING TENANTS VIA HAND-SHAKE METHOD

Entering Resident Info Using KeypadStep 1: On the keypad, enter # plus the ID code (*1111). Re-enter ID code.Step 2: Scroll to RESIDENT INFO. and press Bell button .Step 3: ROOM # will display on the screen. Enter the desired room number (ie: 101, 102, 103, etc.) and press Bell button .Step 4: The room number entered will appear on screen along with a space for the Resident Name. Use the

Keypad and Arrow buttons to key in the resident name (if desired) and press Bell button when finished.Step 5: Repeat steps 3 & 4 for remaining residents.Step 6: Press “X” to return to main menu. Scroll to QUIT and press “X” again to exit programming.

Entering Resident Info Using SoftwareStep 1: Using the CD supplied with the GT-BC, install the GT software and USB cable driver on a PC running

Windows® XP, Windows Vista®, or Windows® 7.Step 2: Open GT software, click GT System Mode .Step 3: Select Resident tab.Step 4: Enter a Room # and Name (if desired) for each resident.Step 5: Connect the USB cable to the PC and to the GT device being programmed. Ensure that the GT device

being programmed is powered.Step 6: Refer to the PC’s device manager to determine which COM Port is being used for the cable driver.Step 7: Select Connection COM Port from the menu bar to see the available COM Ports on the PC.

Select the COM Port that was verified in Step 6.Step 8: Select Connection Export from the menu bar.

(Export sends data to the entrance station. Import pulls data from the entrance station.)

Step 9: A new window will open asking, “Do you want to overwrite the information?” Select Yes .Step 10: Enter ID code (default is *1111) and click OK .

Data will be transferred.

Do not press and hold the Call Button as doing so will clear the memory for this button.

How-To

Video Link

How-To

Video Link

Page 7: GT SERIES - Aiphone

7

PROGRAMMING: ADDRESSING TENANTS VIA HAND-SHAKE METHOD (continued)

GT-DM Entrance Station AddressingStep 1: While in standby mode, enter # plus ID code (default is *1111). Re-enter ID code.Step 2: Use the up / down arrows and scroll to PROGRAMMING . Push the Bell button to enter

programming mode. The amber LED will begin flashing, then remain lit. Once lit, the entry panel is in programming mode. The LCD will show “CONNECTING” while in programming mode.

Step 3: At tenant station, push and release the TALK button or pick up the handset to establish communication with the entrance station in programming mode.

Step 4: Scroll to the station number to be programmed or manually dial the number. When the tenant station number is displayed, push and release the Bell button to assign the address to the tenant station that is active. A blip tone will be heard.

Step 5: Turn off or hang up tenant station (GT-1A: Press TALK again, GT-1C / GT-2C: Press OFF).Step 6: Repeat steps 3-5 for the remaining tenant stations.Step 7: To exit programming, press the “X” button on the panel to return to the main menu (the amber LED

will turn off). Scroll to QUIT and press the “X” button again. The system is now ready for use.

GT-MK Concierge Station AddressingStep 1: While in standby mode, enter # plus ID code (default is *1111). Re-enter ID code.Step 2: Use the up / down arrows and scroll to PROGRAMMING . Press the Bell button to enter

programming mode. The LCD will show “CONNECTING” while in programming mode.Step 3: Pick up the handset on the GT-MK and leave off hook.Step 4: At tenant station, push and release the TALK button or pick up the handset to establish

communication with the GT-MK in programming mode.Step 5: Scroll to the station number to be programmed or manually dial the number. When the tenant

station number is displayed, push and release the Bell button to assign the address to the tenant station that is active. A blip tone will be heard from the GT-MK handset.

Step 6: Turn off or hang up tenant station (GT-1A: Press TALK again, GT-1C / GT-2C: Press OFF).Step 7: Repeat steps 4-6 for the remaining tenant stations.Step 8: To exit programming, press the “X” button on the GT-MK to return to the main menu. Scroll to

QUIT and press the “X” button again. The system is now ready for use.

GT Digital Display Entrance Station AddressingStep 1: Remove front cover from entrance station.Step 2: To enter programming, use a small screwdriver to push and release button under the rubber cap

on front of speaker module (GT-DA-L). The amber LED will begin flashing, then remain lit. Once lit, the entrance station is in programming mode. The LCD will show “CONNECTING” while in programming mode.

Step 3: At tenant station, push and release the TALK button or pick up the handset to establish communication with the entrance station in programming mode.

Step 4: Scroll to the station number to be programmed or manually dial the number. When the tenant station number is displayed, push and release the Bell button to assign the address to the tenant station that is active. A blip tone will be heard.

Step 5: Turn off or hang up tenant station (GT-1A: Press TALK again, GT-1C / GT-2C: Press OFF).Step 6: Repeat steps 3-5 for remaining tenant stations.Step 7: To exit programming, push the button under the rubber cap on the GT-DA-L module again and the

amber LED will turn off. The system is now ready for use.

Transferring Data Between Entrance StationsThe tenant / entrance station hand-shake information can be transferred between entrance stations and / or concierge stations. The above hand-shake procedure must be done at one entrance station before the transfer can occur. Refer to page 40 of the GT Series Installation Manual for this procedure.

16-1

/8"

2-11/16"5-7/8"

GT-DM

16-3

/4"

5-5/16" 1-3/4"1/2"

GTV-DES104

Do not press and hold the Bell button as doing so will clear the memory for this address.

Do not press and hold the Bell button as doing so will clear the memory for this address.

Never do a transfer from an entrance station or concierge station that has not been addressed with tenant stations.

Do not press and hold the Bell button as doing so will clear the memory for this address.

Page 8: GT SERIES - Aiphone

12148| GT Series QuikStart Guide

Decimal

Room ID # Setting:

Use S# for standard system stations 1-48.Use A# for expanded system stations 1-250.Use B# for expanded system stations 251-500.

For tenant stations 251-500, the dip switch assignment is the same as 1-250. Tenant stations 1-250 wire to Sub 1A and Sub 1B of the GT-BCX while tenants 251-500 wire to Sub 2A and Sub 2B(see page 4).

Note: 8 binary digits allows for 255 unique numbers. Only numbers 1-250 are used by the GT system.

PROGRAMMING: ADDRESSING TENANTS VIA DIP SWITCH METHOD

Step 1: Set dip switches for all GT-1C and GT-2C stations using the chart example to the right. (The full GT Dip Switch Setting Worksheet can be found on the CD included with the GT-BC.)

Step 2: Apply power to system.Step 3: Install the GT software and USB cable driver on a computer running

Windows® XP, Windows Vista®, or Windows® 7. (Refer to page 6 for COM Port selection steps.)

Step 4: Open the GT software, select [GT System Mode].Step 5: Select the Resident tab.Step 6: Enter a Room # and Name for each tenant to be programmed.Step 7: Select View Room ID # Setting from the menu bar (see Figure 1).

Figure 1

Figure 2

Binary

Figure 3

Dip Switch

1 52 63 74 8

1 52 63 74 8

1 52 63 74 8

1 52 63 74 8

1 52 63 74 8

1 52 63 74 8

1 52 63 74 8

1 52 63 74 8

ID #

S4

S8

S2

S6

S1 A1

A5

A3

A7

A2

A6

A4

A8

B251

B255

B253

B257

B252

B256

B254

B258

S5

S3

S7

Figure 4 Figure 5

Step 9: Select Connection Export from the menu bar (see Figure 3). (Export sends data to the entrance station. Import pulls data from the entrance station.)

Step 8: For each Binary Dip Switch setting made in Step 1, enter the appropriate ID into the Room ID # Setting field. Ensure that the correct correlation is kept between tenant name and actual unit (see Figure 2).

Step 10: Check the LinkData box and select Yes (see Figure 4).

Step 11: Enter ID code (default is *1111) and click OK (see Figure 5). Data will be transferred.

Std Exp(Sub 1)

Exp(Sub 2)

Aiphone Corporation1700 130th Ave. NE Bellevue, WA 98005Ph: (800) 692-0200 Fax: (425) 455-0071www.aiphone.com [email protected]

Visit our website for complete information and literature on the GT Series Multi-Tenant Entry Security System.www.aiphone.com/home