Upload
groundhog-industries
View
272
Download
3
Embed Size (px)
DESCRIPTION
The Groundhog system is compatible with Ausplow, however there is no relationship between Groundhog Industries and Ausplow Pty Ltd. Ausplow Pty Ltd has not approved the use of Groundhog Industries parts on its machinery.
Citation preview
1
Product Guide 2015
2 32
PrecisionFertiliser & Seeding PartsWhy choose Groundhog Industries? Groundhog Industries design precision fertiliser and seeding parts to achieve the following goals:
Reduce Downtime
This is achieved by using a quick change, cast steel, knife point, a deep banding liquid / granular boot free from stainless tubing and a closer plate with replaceable wear shoe.
Reduce Replacement cost
Through innovative design Groundhog Products are better value per hectare than their competitors.
Provide More Effective Product Delivery
This is achieved by a cast iron fertiliser boot, eliminating the use of stainless steel tubing for liquid delivery.
Longer lasting Wear Resistant Products
By using the highest grade of tungsten carbide available as well as state of the art application processes, all Groundhog products have been designed to offer maximum protection from wear.
KNIFE HOLDER (item 11)
• Change points quickly by removing the split pin with a hammer, no rattle gun, no lost skin loosening bolts.
• Manufactured from cast steel for superior strength.
• Bolt heads are counter sunk in holder to cater for tapered knife head.
• Holder takes the brunt of the load in combination with the load pad at the rear of the knife.
• Holder employs the same length bolts as standard points.
Design Reg: 335056Holder
Knife Holder (11)
Knife (30/31/32)
Trash Guard (51) Wear Shoe Holder (21)
seed
granular fertiliser
liquid fertiliser
Liquid & Granular Fertiliser Boot (27)
Wear Shoe (23/24)
2 32
LIQUID & GRANULAR FERTILISER BOOT (item 27)
• Robust cast boot provides accurate placement of liquid and granular fertiliser below the seed. This design enables the boot to be deeper in the ground, and the steel side walls of the boot provide a wear resistant shield delaying the flow of soil back into the trench.
• Using plastic tube eliminates the need for expensive stainless steel tubing, the need to weld a nut to the rear of the point and prevents bending or blockages.
• The plastic tube remains undisturbed during point changes saving time and money.
• The boots design provides a protected pathway for the plastic fertiliser tube to ground level.
• Boot is compatible with stainless and powder coated granular fertiliser tubes.
Design Reg: 335057
WEAR SHOE HOLDER (item 21)
WEAR SHOE 30MM (item 23)
WEAR SHOE 30MM H/D (item 24)
• Most heavy duty closing tool on the market.
• Made from two parts - Wear shoe holder’ and ‘Wear Shoe’.
• The holder provides the same bolt hole pattern as a genuine closing tool.
• The wear shoe is made from cast steel and is secured using a high tensile roll pin (roll pin does not receive any load). Thick casting on wear shoe and large tungsten tiles on all sizes eliminates premature wear and reduces replacement costs.
Design Reg: 335058
Side
Plastic Tube
Rear Front
Wear Shoe Holder
30HD 30
Wear Shoe
8”
7”
6”
Knife: 8” (item 30), 7” (item 31), 6” (item 32)
• Tapered Cast steel design making it easy to insert & remove in holder.
• Highest grade of carbide available and applied using induction welding, with proven results for wear and shock loads.
• Knife blade is tapered to increase wear life, 12mm at the front and 18mm at rear. Both point and holder are low profile allowing minimal soil throw, good trash handling.
• Low cost and quick to change.
Design Reg: 335055
Wear Shoe (23/24)
1
3
4
5
6
7
16 18 17 19 20 21
68
2 14
6
2
15 2
42
44
48
49 46 43
47 47a
48a
ITEM DESCRIPTION PART NUMBER
13. Nut 1/2” UNC Nyloc 12NCNN
14. Press Wheel Dust seal 37 x 7 x 24 GHPWSEAL
15. Press wheel Bearing PWBJ
16. Nut 1/2” UNC Plain Nut 12NC8NBU
17. Bolt M12 x 150 M12X150
18. Washer 1/2” spring ZP 12SQSW
19. Roll Pin GH010
20. Plastic Seed Boot - 42 or 32 ID GH42 / GH32
21. Wear Shoe Holder GH012
22. Bolt 1¾” x ½” UNC 12X1.14NC8B
23. Wear Shoe 30mm wide GH030
24. Wear Shoe 30mm wide HD Tungsten GH030HD
ITEM DESCRIPTION PART NUMBER
1. Bolt M12 x 90 ZP M12X90
2. Flat Washer M12 ZP Hardened M12WF
3. Seal Cap - ZP Housing & Dust Seal GHSEAL
4. Short Bush - Sintered, Oil impregnated GHSB
5. Long Bush - Sintered, Oil impregnated GHLB
6. Nut M12 Conelock M12CONE
7. Spring 5.6x 42x120 SP120
8. Joiner Liquid GHFITTING
9. Clevis Pin GH005
10. Split Pin GHSPIN
11. Knife Holder GH006
12. Bolt 1/2” UNC x 31/2” Grade 8 12X3.12NC8B
There is no relationship between Groundhog Industries and Ausplow Pty Ltd. Ausplow Pty Ltd has not approved the use of Groundhog Industries parts on its machinery.
8
9
10
11
12
13
22
2324 27
28
29
30
31
32
51
ITEM DESCRIPTION PART NUMBER
47a. Side Arm Upper (Short) ARMUPA
48. Side Arm Lower (Long) ARMLOW
48a. Side Arm Upper (Short) ARMLOWA
49. Press Wheel Arm (New Style) PWARM
51. Trash Guard (inc 1¾” x ½” UNC bolt wshr + nut) GHTRASH
60. Bush Housing BHOUSING
61. Bush Housing Nut BHN
68. Mud Scraper Holder MSH
69. Stainless Fert Tube SFT
70. Fert Tube Bracket FTB
72. Wear Shoe Holder Chain WSHC
* Groundhog Industries reserve the right to change details at any time.
ITEM DESCRIPTION PART NUMBER
27. Boot (Cast) - Liquid / Granular GH011
28. Rubber Sleeve JOINER
29. Hose Clamp GH44 / GH51
30. Knife - 8” GH007
31. Knife - 7” GH0014
32. Knife - 6” GH016
42. Pin Spring Holder P-Sholder
43. Stopper GHSTOPPER
44. Retaining Spring RSPRING
45. Spring SSPRING
46. 70mm Mud scraper (New Style) 70SCRAPPER
47. Side Arm Upper (Long) ARMUP
60 6961 70 72
Parts & Accessories
Joiner Liquid Note: Sizes on application. Please contact Groundhog Industries.
ITEM No.8 - Part Number: GHFITTING
Seal Cap Assembly
ITEM No.3 - Part Number: GHSEAL
Rubber Sleeve
ITEM No.28 - Part Number: JOINER
Press Wheel Bearing
ITEM No.15 - Part Number: PWBJ
Press Wheel Dust Seal 37x7x24
ITEM No.14 - Part Number: GHPWSEAL
Spring 5.6x 42x120
ITEM No.7 - Part Number: SP120
Bolt M12 x 90 ZP (Thread Lock)
ITEM No.1 - Part Number: M12X90
Flat Washer M12 ZP
ITEM No.2 - Part Number: M12WF
Nut M12 Conelock
ITEM No.6 - Part Number: M12CONE
Wear Shoe Holder Bolt
ITEM No.22 - Part Number: 12X1.14C8B
ITEM No.18 - Part Number: 12X1.14C8B
ITEM No.2 - Part Number: 12X1.14C8B
Clevis Pin
ITEM No.10 - Part Number: GHSPIN
ITEM No.9 - Part Number: GH005
Split Pin
Hose Clamp 19 – 44 Worm Drive SS
ITEM No.29 - Part Number: GH44
Hose Clamp 27 - 51 Worm Drive SS
ITEM No.29 - Part Number: GH51
Short Outer Bush, Sintered Nickel, Oil impregnated
ITEM No.4 - Part Number: GHSB
Plastic Seed Boot
ITEM No.20 - Part Number: GH32
ITEM No.20 - Part Number: GH42
Long Inner Bush, Sintered Nickel, Oil impregnated
ITEM No.5 - Part Number: GHLB
Open End Gear Spanner, 19mm Ratcheting.
Part Number: GHK3093
Knife Holder Bolt
ITEM No.12 - Part Number: 12X3.12NC8B
Knife Holder Bolt
ITEM No.13 - Part Number: 12NCNN
Bolt M12 x 150
ITEM No.17 - Part Number: M12X150
Visit our website for more details and video of the system in action www.groundhogindustries.com.auWARRANTY INFORMATIONAs the selection, set-up and use of tillage and seeding equipment is affected by variables beyond our control, neither the Manufacturer nor any persons employed on its behalf including dealers or agents are liable for any loss or damage, whether consequential or otherwise, resulting from the use of its products. Warranty may / may not apply where any product is used for other than its intended and recommended purpose, or is subjected to pressures, loads or conditions beyond that for which it is designed. Should a product not perform its intended or recommended function, contact Groundhog Industries.
Trash Guard
ITEM No.51 - Part Number: GHTRASH
70mm Mud scraper (New Style)
ITEM No.46- Part Number: 70SCRAPPER
Pin Spring Holder
ITEM No.42 - Part Number: P-Sholder
Spring for Fert Tube
ITEM No.45 - Part Number: SSPRING
Mud Scraper Holder
ITEM No.68 - Part Number: MSH
Press Wheel Arm (New Style)
ITEM No.49 - Part Number: PWARM
Side Arm Upper (Long)
Stainless Fert Tube
ITEM No.47 - Part Number: ARMUP
ITEM No.69 - Part Number: SFT
Stopper
ITEM No.43 - Part Number: GHSTOPPER
Side Arm Lower (Long)
Fert Tube Bracket
ITEM No.48 - Part Number: ARMLOW
ITEM No.70 - Part Number: FTB
Side Arm Upper (Short)
ITEM No.47a - Part Number: ARMUPA
Bush Housing
ITEM No.60 - Part Number: BHOUSING
Retaining Spring
ITEM No.44 - Part Number: RSPRING
Bush Housing Nut
ITEM No.61 - Part Number: BHN
Side Arm Lower (Short)
ITEM No.48a - Part Number: ARMLOWA
8
For Sales Contact:
Tel: 0405 605 210 Fax: (08) 9433 3753
PO BOX 291 South Fremantle 616211 Marryat Court Hamilton Hill 6163.
Email: [email protected]