-
8/12/2019 GPS PAPAI Starter Kit b80 v01
1/22
c
Starter Kit B80 User Guideu
ide
-
8/12/2019 GPS PAPAI Starter Kit b80 v01
2/22
-
8/12/2019 GPS PAPAI Starter Kit b80 v01
3/22
-
8/12/2019 GPS PAPAI Starter Kit b80 v01
4/22
-
8/12/2019 GPS PAPAI Starter Kit b80 v01
5/22
-
8/12/2019 GPS PAPAI Starter Kit b80 v01
6/22
Starter Kit B80 User Guide
1.4 Ordering Information
18c
1.4 Ordering Information
1.5 Scope of Delivery
The modules and adapters for use with the Starter Kit B80 are
not included in the scope of de-
livery.
Table 1: Starter Kit B80delivery package
Description Supplier Ordering information
Starter Kit B80 Cinterion Order number: L30960-N0040-A100
Table 2: Starter Kit B80delivery package
Quantity Description
1 Starter Kit B80
1 Hirose antenna cable 60mm, 50 Ohms
1 Hirose antenna cable100mm, 50 Ohms
1 USB A to Mini-USB Y-cable 1m
-
8/12/2019 GPS PAPAI Starter Kit b80 v01
7/22
-
8/12/2019 GPS PAPAI Starter Kit b80 v01
8/22
-
8/12/2019 GPS PAPAI Starter Kit b80 v01
9/22
Starter Kit B80 User Guide
3 Step-By-Step Startup
18c
3 Step-By-Step Startup
To set up the Starter Kit B80 please follow the below
step-by-step instructions. The mentioned
interfaces - connectors and switches - are illustrated in
Chapter 2. A more detailed descriptionof these interfaces can be
found in Chapter 4:
Download and extract the virtual COM port (VCP) driver. The
virtual COM port (VCP) driverwill cause the Starter Kit B80 -
connected to a PC via USB - to appear as an additional COM
port available on the PC. For details on the USB-to-UART bridge
see Chapter 4.The VCP driver can be downloaded free of charge from
Future Technology Devices Inter-national Ltd.
(http://www.ftdichip.com/Drivers/VCP.htm).
Set the power supply switch to 5V (delivery default).
Connect the integrated RF antenna (and if need be GPS antenna).
Figure 3shows theantenna connection for a PH8 module mounted onto
the board-to-board connector using
the modules U.FL connectors. External antennas can also be
connected.
Mount the module onto the Starter Kit B80s 80-pin board-to-board
connector.
Insert the SIM as shown in Figure 3.
Figure 3: Starter Kit B80 with mounted module and SIM
-
8/12/2019 GPS PAPAI Starter Kit b80 v01
10/22
-
8/12/2019 GPS PAPAI Starter Kit b80 v01
11/22
-
8/12/2019 GPS PAPAI Starter Kit b80 v01
12/22
-
8/12/2019 GPS PAPAI Starter Kit b80 v01
13/22
Starter Kit B80 User Guide
4.2 Board-to-Board Connector
18c
4.2 Board-to-Board Connector
The modules are mounted to the Starter Kit B80 via the 80-pin
board-to-board connector asshown in Figure 3.
4.3 Status LEDs
The Starter Kit B80 features two status LEDs indicating the
evaluation modules power on/offstate ("ON"; blue) as well as the
current data transfer state ("RXTX"; white).
4.4 SIM Card Holder
The Starter Kit B80 has a card holder on its bottom side for a
SIM to be inserted. The SIM cardholder supports normal card
operation, but does not support the SIM card detection
function-ality. The evaluation modules card detection line is
connected to the 2x40-pin connector only
in order to support card detection on the optional DSB-Mini.
4.4.1 Component SIM Card
The Starter Kit B80 provides a land pattern for an optional use
of a component UICC (SIM/USIM/MIM). The component SIM will have to
be soldered manually and can then be used in-
stead of SIM cards inserted into the SIM card holder.
Depending on the manufacturer and package of the employed UICC,
pin 6 or pin 7 is used asI/O line. Thus, it is necessary to place a
0Ohm resistor either for R28 or R29. Please refer to
the package specification of the UICC for details.
-
8/12/2019 GPS PAPAI Starter Kit b80 v01
14/22
-
8/12/2019 GPS PAPAI Starter Kit b80 v01
15/22
Starter Kit B80 User Guide
4.6 Switches
18c
4.6 Switches
4.6.1 Ignition
The Ignitionbutton ("IGT") is used to switch on the evaluation
module plugged onto the Starter
Kit B80.
To switch the module off the AT comand AT^SMSO should be used.
Alternatively, the USB
power supply can be unplugged. Note that some Terminal programs
(e.g., ZOC) will not noticethat the USB cable was unplugged. In
this case the Terminal program has to be restarted.
4.6.2 Power Supply Switch
The Starter Kit B80 has a switch to select the power supply
path:
5V (default)The 5V power supply path collects the supply from
the USB interfaces on the Starter Kit
B80 and the 5V supply from the 2x40-pin connector.
A post LDO regulates the modules operating voltage down to 3.8V.
Battery
The battery power supply path provides a direct power source on
the 2x40pin connectorwithout additional circuitry except the switch
resistance (~20m).
If the Starter Kit B80 operates standalone, the switch must be
set to 5V to supply the modulethrough the 5V power supply path.
Only if the Starter Kit B80 is mounted onto the optional
DSB-Mini and the module is suppliedby an external battery connected
to the DSB-Mini, must the switch be set to BAT.
Starter Kit B80
circuit:
ICs, LEDsVUSB
USB
(USB/Supply)
USB
(USB-to-UART/Supply)
V480
ector
-
8/12/2019 GPS PAPAI Starter Kit b80 v01
16/22
-
8/12/2019 GPS PAPAI Starter Kit b80 v01
17/22
-
8/12/2019 GPS PAPAI Starter Kit b80 v01
18/22
-
8/12/2019 GPS PAPAI Starter Kit b80 v01
19/22
-
8/12/2019 GPS PAPAI Starter Kit b80 v01
20/22
-
8/12/2019 GPS PAPAI Starter Kit b80 v01
21/22
-
8/12/2019 GPS PAPAI Starter Kit b80 v01
22/22
