40
GOVERNMENT OF PAKISTAN MINISTRY OF FINANCE, ECONOMIC AFFAIRS, STATISTICS AND REVENUE (REVENUE DIVISION) *** Islamabad, the 1st July, 2006. NOTIFICATION (CUSTOMS) S.R.O. 693 (I)/2006.- In exercise of the powers conferred by sub-section (5) of section 18 of the Customs Act, 1969 (IV of 1969), the Federal Government is pleased to levy additional customs-duty on the import of goods, - - (a) at the rate of 15% of the customs value on goods classifiable under tariff headings of the First Schedule to the Customs Act, 1969, as specified in Appendix I to this notification 1 [: 2&4 [omitted] (b) at the rates specified in column (4) of the Table below on the sub-components and components, specified in Appendix I and Appendix II as mentioned in column (3) of the said Table, imported as part of any kit form for the assembly or manufacturing of motor cars and vehicles classifiable under headings mentioned in column (2) of that Table, namely-- TABLE “APPENDIX-I HS Code DESCRIPTION (1) (2) 4008.1110 - - - Following components for vehicles of chapter 87:- (1) Weather strips for doors and luggage compartments for motor cars of heading 87.03 and vehicles of sub - heading 8703.2113, except weather strip moulding (inner / outer) for glass (2) Weather strips for doors and glass for vehicles of sub- heading 8704.2190 Sr. No. PCT Headings Appendix Rate of additional customs-duty (1) (2) (3) (4) 1 87.01 (Agricultural Tractors) Appendix II 35% ad val. 2 8701.2090 and 8701.9060 Appendix II 35% ad val. 3. 87.01 (Tractors other than mentioned at Sr. No.1 and 2 above). Appendix II 25% ad val. 4 87.02 (CNG dedicated buses) Appendix II 35% ad val. 5 87.02 (Non-CNG buses) Appendix II 30% ad val. 6 87.03 6 [excluding 4-stoke auto rickshaw of PCT heading 8703.2115] Appendix I 4 [17.5]%ad val. 6 [6a 4-stroke auto rickshaw of PCT heading 8703.2115 Appendix I 30% ad val. 7 87.04 (vehicles of g.v.w exceeding 5 tons). Appendix II 25% ad val. 8 87.04 (vehicles of g.v.w not exceeding 5 tons) Appendix I 30% ad val. 9 87.11 Appendix I 3,4&6 [32.5% ad val.]

GOVERNMENT OF PAKISTANengineeringpakistan.com/EngPak1/sro/2006sro693.pdfAct, 1969 (IV of 1969), the Federal Government is pleased to levy additional customs-duty on the import of goods,

  • Upload
    others

  • View
    3

  • Download
    0

Embed Size (px)

Citation preview

Page 1: GOVERNMENT OF PAKISTANengineeringpakistan.com/EngPak1/sro/2006sro693.pdfAct, 1969 (IV of 1969), the Federal Government is pleased to levy additional customs-duty on the import of goods,

GOVERNMENT OF PAKISTAN MINISTRY OF FINANCE, ECONOMIC AFFAIRS, STATISTICS AND REVENUE

(REVENUE DIVISION) ***

Islamabad, the 1st July, 2006.

NOTIFICATION (CUSTOMS)

S.R.O. 693 (I)/2006.- In exercise of the powers conferred by sub-section (5) of section 18 of the Customs Act, 1969 (IV of 1969), the Federal Government is pleased to levy additional customs-duty on the import of goods, --

(a) at the rate of 15% of the customs value on goods classifiable under tariff headings of the First Schedule to the Customs Act, 1969, as specified in Appendix I to this notification 1[:

2&4[omitted]

(b) at the rates specified in column (4) of the Table below on the sub-components and components,

specified in Appendix I and Appendix II as mentioned in column (3) of the said Table, imported as part of any kit form for the assembly or manufacturing of motor cars and vehicles classifiable under headings mentioned in column (2) of that Table, namely--

TABLE

“APPENDIX-I HS Code DESCRIPTION

(1) (2) 4008.1110 - - - Following components for vehicles of chapter 87:-

(1) Weather strips for doors and luggage compartments for motor cars of heading 87.03 and vehicles of sub - heading 8703.2113, except weather strip moulding (inner / outer) for glass

(2) Weather strips for doors and glass for vehicles of sub- heading 8704.2190

Sr. No. PCT Headings Appendix Rate of additional

customs-duty (1) (2) (3) (4) 1 87.01 (Agricultural Tractors) Appendix II 35% ad val. 2 8701.2090 and 8701.9060 Appendix II 35% ad val. 3. 87.01 (Tractors other than mentioned at Sr. No.1

and 2 above). Appendix II 25% ad val.

4 87.02 (CNG dedicated buses) Appendix II 35% ad val. 5 87.02 (Non-CNG buses) Appendix II 30% ad val. 6 87.03 6[excluding 4-stoke auto rickshaw of PCT heading

8703.2115] Appendix I 4[17.5]%ad val.

6[6a 4-stroke auto rickshaw of PCT heading 8703.2115 Appendix I 30% ad val. 7 87.04 (vehicles of g.v.w exceeding 5 tons). Appendix II 25% ad val. 8 87.04 (vehicles of g.v.w not exceeding 5 tons) Appendix I 30% ad val. 9 87.11 Appendix I 3,4&6[32.5% ad

val.]

Page 2: GOVERNMENT OF PAKISTANengineeringpakistan.com/EngPak1/sro/2006sro693.pdfAct, 1969 (IV of 1969), the Federal Government is pleased to levy additional customs-duty on the import of goods,

2

(3) Weather strips for doors for vehicles of sub – heading 8704.3190 4008.1910 - - - Following components for vehicles of chapter 87:-

(1) Weather strips for doors and luggage compartments for motor cars of heading 87.03 and vehicles of sub - heading 8703.2113, except weather strip moulding (inner / outer) for glass

(2) Weather strips for doors and glass for vehicles of sub- heading 8704.2190 (3) Weather strips for doors for vehicles of sub – heading 8704.3190

4008.2110 - - - Following components for vehicles of chapter 87:- (1) Weather strip for doors and luggage compartments for motor cars of

heading 87.03 and vehicles of sub - heading 8703.2113, except weather strip moulding (inner / outer) for glass

(2) Weather strips for doors and glass for vehicles of sub- heading 8704.2190 (3) Weather strips for doors for vehicles of sub – heading 8704.3190

4008.2910 - - - Following components for vehicles of chapter 87:- (1) Weather strips for doors and luggage compartments for motor cars of

heading 87.03 and vehicles of sub - heading 8703.2113, except weather strip moulding (inner / outer) for glass

(2) Weather strips for doors and glass for vehicles of sub- heading 8704.2190 (3) Weather strips for doors for vehicles of sub – heading 8704.3190

4009.1120 - - - Following components for vehicles of chapter 87 (1) Water hoses of a kind used for engine cooling system / heater for motor

cars of heading 87.03 and vehicles of sub - heading 8703.3223 (2) Hose side demister for motor cars of heading 87.03 (not exceeding 800cc) (3) Water hoses used for engine cooling / heater systems, hoses brake

reservoir, air cleaner hose, cool air hoses for vehicles of sub - heading 8703.2113 and 8703.2193

(4) Water hoses of a kind used for engine cooling system / heater for vehicles of sub - heading 8704.2190

(5) Water hoses for engine cooling system, air cleaner hoses and brake oil reservoir hose for vehicles of sub -heading 8704.3190

(6) Engine cooling system / radiator hoses and fuel tubes,meant for industrial assembly / manufacture of vehicles ofsub - heading 8703.2115

(7) Air intake hoses, radiator hoses, intercooler hoses and heater hoses, meant for industrial assembly / manufacture of vehicles of sub -heading 8703.3225

4009.2120 - - - Following components for vehicles of chapter 87

(1) Water hoses of a kind used for engine cooling system / heater for motor cars of heading 87.03 and vehicles of sub- heading 8703.3223

(2) Hose side demister for motor cars of heading 87.03 (not exceeding 800cc) (3) Water hoses used for engine cooling / heater systems, hoses brake

reservoir, air cleaner hose, cool air hoses for vehicles of sub - heading 8703.2113 and 8703.2193

(4) Water hoses of a kind used for engine cooling system /heater for vehicles of sub - heading 8704.2190

(5) Water hoses for engine cooling system, air cleaner hoses and brake oil reservoir hose for vehicles of sub -heading 8704.3190

(6) Engine cooling system / radiator hoses and fuel tubes, meant for industrial assembly / manufacture of vehicles of sub - heading 8703.2115

Page 3: GOVERNMENT OF PAKISTANengineeringpakistan.com/EngPak1/sro/2006sro693.pdfAct, 1969 (IV of 1969), the Federal Government is pleased to levy additional customs-duty on the import of goods,

3

(7) Air intake hoses, radiator hoses, intercooler hoses and heater hoses, meant for industrial assembly /manufacture of vehicles of sub -heading 8703.3225

4009.3120 - - - Following components for vehicles of chapter 87 (1) Water hoses of a kind used for engine cooling system /heater for motor

cars of heading 87.03 and vehicles of sub- heading 8703.3223 (2) Hose side demister for motor cars of heading 87.03 (not exceeding 800cc) (3) Water hoses used for engine cooling / heater systems, hoses brake

reservoir, air cleaner hose, cool air hoses for vehicles of sub - heading 8703.2113 and 8703.2193

(4) Water hoses of a kind used for engine cooling system /heater for vehicles of sub - heading 8704.2190

(5) Water hoses for engine cooling system, air cleaner hoses and brake oil reservoir hose for vehicles of sub - heading 8704.3190

(6) Engine cooling system / radiator hoses and fuel tubes, meant for industrial assembly / manufacture of vehicles of sub - heading 8703.2115

(7) Air intake hoses, radiator hoses, intercooler hoses and heater hoses, meant for industrial assembly / manufacture of vehicles of sub -heading 8703.3225

4009.4120 - - - Following components for vehicles of chapter 87

(1) Water hoses of a kind used for engine cooling system /heater for motor cars of heading 87.03 and vehicles of sub- heading 8703.3223

(2) Hose side demister for motor cars of heading 87.03 (not exceeding 800cc) (3 )Water hoses used for engine cooling / heater systems, hoses brake

reservoir, air cleaner hose, cool air hoses for vehicles of sub - heading 8703.2113 and 8703.2193

(4) Water hoses of a kind used for engine cooling system / heater for vehicles of sub - heading 8704.2190

(5) Water hoses for engine cooling system, air cleaner hoses and brake oil reservoir hose for vehicles of sub - heading 8704.3190

(6) Engine cooling system / radiator hoses and fuel tubes,meant for industrial assembly / manufacture of vehicles ofsub - heading 8703.2115

(7) Air intake hoses, radiator hoses, intercooler hoses and heater hoses, meant for industrial assembly / manufacture of vehicles of sub -heading 8703.3225

4012.9020 - - - Rim flaps, mud flaps / guards and rubber mouldings (except packing rubber and rubber for on / off switch) for vehicles of heading 87.11

4016.9930 - - - Following component for vehicles of chapter 87

(1) Articles for mounting silencers, exhaust pipes and mufflers for motor cars of heading 87.03 and vehicles of sub - headings 8703.2113, 8703.2193, 8703.3223, 8704.2190 and 8704.3190

(2) Floor mats, grommets for transfer box lever, exhaust pipe mountings, covers for pedals, bump stop and front cover for center tunnel, meant for industrial assembly / manufacture of vehicles of sub - heading 8703.3225

(3) Rubber cover for kick starter lever, foundation rubberfor engine mounting, rubber bushings, rubber plugs,rubber insulators, packing rubber for wind screen, rubbermountings for silencer pipes bushes, boots, and mudflappers, meant for industrial assembly / manufacture ofvehicles of sub - heading 8703.2115

Page 4: GOVERNMENT OF PAKISTANengineeringpakistan.com/EngPak1/sro/2006sro693.pdfAct, 1969 (IV of 1969), the Federal Government is pleased to levy additional customs-duty on the import of goods,

4

(4) Rubber cushions for bonnet for vehicles of heading 8704.2190 (5) Rubber cushions for bonnet, rubber drain plug, hole covers and pads /

cushions for absorbing shock / noise in struts / suspensions, for vehicles of heading 8703.3223

(6) Rubber for bottom channel for holding window glass for motor cars of heading 87.03 and vehicles of sub -headings 8703.2113 and 8703.2193

(7) Runs for glasses for motor cars of heading 87.03 ( not exceeding 1200cc) and vehicles of sub – headings 8703.2193, 8704.2190 and 8704.3190

(8) Trim door opening and door moulding for door opening for motor cars of heading 87.03 and vehicles of sub - heading 8703.2113 and 8703.2193

4821.1010 - - - Paper graphics of a kind used for decoration for vehicles of heading 87.11 5703.2020 - - - Of a kind used in motor cars of heading 87.03 and vehicles of sub-

headings 8703.2113, 8703.2193, 8703.3223, 8704.2190, 8704.3190 (cut to size and shaped)

5703.3020 --- Of a kind used in vehicles of heading 87.03 and vehicles of sub-headings 8703.2113, 8703.2193, 8703.3223, 8704.2190, 8704.3190(cut to size and shaped)

6813.2010 - - - Of asbestos for vehicles of heading 87.11

7007.1111 - - - - (1) Rear and window glasses for vehicles of sub -heading 8704.3190 (2) Glasses for doors, glass plain, glass window (sliding), glass for rear door,

glass for rear quarter window and glass for wind screen for vehicles of sub - heading 8703.3225

7007.2111 - - - - (1) Rear and window glasses for vehicles of sub -heading 8704.3190 (2) Glasses for doors, glass plain, glass window (sliding), glass for rear door,

glass for rear quarter window and glass for wind screen for vehicles of sub - heading 8703.3225

7009.1010 - - - Rear view mirrors for motor cars of heading 87.03,and vehicles of sub-headings 8703.2113, 8703.2115,8703.3223, 8704.3190, 8703.3225 and vehciles ofheading 87.11

7014.0010 - - - Glass for head lamps for vehicles of heading 87.11 7315.1910 - - - Adjuster for chain for vehicles of heading 87.11 7320.1010 - - - For motor cars of heading 87.03 and vehicles of sub-headings

8703.2113, 8703.2193, 8704.2190, and 8704.3190 8206.0010 - - - For motor cars of heading 87.03 and vehicles of sub-headings

8703.2113, 8703.2115, 8703.2193, 8703.3223, 8703.3225 8704.2190 and 8704.3190

8301.2010 - - - Door locks for vehicles of sub - heading 8704.3190; Locks, meant for vehicles of heading 87.11

8302.1010 - - - (1) Of a kind used in vehicles for doors, luggage compartment lid, seats and bonnet for motor cars of heading 87.03 and vehicles of sub-headings 8703.2113 (except die casting type, sliding door hinges and quarter window hinges)

(2) Of a kind used in vehicles for doors and seats for vehicles of sub-headings 8703.2193, 8703.3223.

(3)Of a kind used in vehicles for rear deck for vehicles of sub- heading 8704.2190

(4)Of a kind used for doors and rear deck for vehicles of sub - heading 8704.3190

Page 5: GOVERNMENT OF PAKISTANengineeringpakistan.com/EngPak1/sro/2006sro693.pdfAct, 1969 (IV of 1969), the Federal Government is pleased to levy additional customs-duty on the import of goods,

5

8302.3010 - - - (1) Latch assembly for hood/doors (manual type) of a kind used in vehicles for doors, luggage compartment lid and bonnet, for motor cars of heading 87.03 (not exceeding 1200cc) and vehicles of sub-heading 8703.2113( except back door latches), 8704.2190 and 8704.3190:

(2) Grip bars/ assistants, grab rails and parts thereof for motor cars of heading 87.03 and vehicles of sub-headings 8703.2113, 8703.2193 (except foamed type), 8703.3223, 8704.2190 and 8704.3190

(3) Strikers for latches for motor cars of heading 87.03 and vehicles of sub-heading 8703.3223 and 8704.2190

(4) Window opening mechanism, rack and pinion type for motor cars of heading 87.03 and vehicles of sub-headings 8703.2113, 8703.2193, 8704.2190, and 8704.3190:

(5) Tail board fittings for vehicles of heading 87.11

8310.0020 - - - Number plates assembly and parts thereof for vehiclesof heading 87.11

8407.3110 - - - For vehicles of heading 87.11 8407.3210 - - - For vehicles of heading 87.11 8407.3310 - - - For vehicles of sub-headings 8703.2113 and, 8704.3190 8409.9111 - - - - Following for engines as well as of vehicles of heading 87.11;

(1) Cylinders (2) Cylinder Blocks (3) Cylinder Liners (4) Crank Case & case covers (5) Cylinder Head covers 6[(6) Piston (7) Sprocket Cam]

8409.9120 - - - Following parts of engines for vehicles of Chapter 87:

(1) Intake manifold for automotive engines as well as of motor cars of heading 87.03 (not exceeding 800cc) and vehicles of sub-headings 8703.2113 and 8704.3190

(2) Cover cylinder head for automotive engines as well as of motor cars of heading 87.03 (not exceeding 800cc) and vehicles of sub-heading 8703.2113 and 8704.3190

(3) Oil pan, for automotive engines as well as for motor cars of heading 87.03 (not exceeding 1200cc) and vehicles of sub-heading 8703.2113 and 8704.3190

(4) Timing belt cover (Steel Sheet / Plastic) for automotive engines as well as of motor cars of heading 87.03 and vehicles of sub-headings 8703.2113, 8703.2193 and 8704.3190

(5) Exhaust manifold (Iron Casting Type) for automotive engines as well as of motor cars of heading 87.03 and vehicles of sub-heading 8703.2113 and 8704.3190

(6) Oil strainer for automotive engines as well as of motor cars of heading 87.03 (not exceeding 1200cc) and vehicles of sub-headings 8703.2113, 8703.2193 and 8704.3190;

(7) Cover exhaust manifold for engines as well as of motor cars of heading 87.03 (not exceeding 800cc) and vehicles of sub-headings 8703.2113, 8703.2193 and 8704.3190;

Page 6: GOVERNMENT OF PAKISTANengineeringpakistan.com/EngPak1/sro/2006sro693.pdfAct, 1969 (IV of 1969), the Federal Government is pleased to levy additional customs-duty on the import of goods,

6

(8) Pipe Water outlet / inlet for engines as well as of motor cars of heading 87.03 (not exceeding 1200cc)

8413.3030 - - - Following parts of vehicles of Chapter 87; (1) Oil pump assembly for motor cars of heading 87.03 (not exceeding 800cc)

and vehicles of sub-headings 8703.2113 and 8704.3190 (2) Water pump for internal combustion piston engines for motor cars of

heading 87.03 and vehicles of sub-heading 8703.2113 and 8704.3190 8415.2010 - - - For motor cars of heading 87.03 and vehicles of sub-headings 8703.2113

and 8703.2193

8421.2310 - - - For motor cars of heading 87.03, and vehicles of sub-headings 8703.2113, 8704.3190, 8703.3225 and vehicles of heading 87.11 (other than foam type)

8421.3110 - - - For motor cars of heading 87.03 ( not exceeding 800cc), vehicles of sub-headings 8703.2113, 8703.2115, 8703.2193, 8703.3225, 8704.2190, 8704.3190 and vehicles of heading 87.11 (other than foam type)

8425.4900 - - Other 6[8481.8020 - - - Cock for fuel tank for vehicles of heading 87.11]

8483.1012 - - - - Shaft for rocker arm, shaft worm, spindle shaft complete gear, spindle for cam guide sprocket and crank shaft for vehicles of heading 87.11

8483.4012 - - - - Gears (C1, C2, C3, C4, M2, M3, M4) for vehicles of heading 87.11

8483.5010 - - - (1) Flywheels (without built-in gear ring) for motor cars of heading 87.03 and vehicles of sub-headings 8703.2113, 8703.2193, and 8704.3190; Fly wheels for vehicles of heading 87.11

(2) Pulley for crank shaft for motor cars of heading 87.03 (not exceeding 1200cc) and vehicles of sub-headings8703.2113, 8703.2193, and 8704.3190

(3) Pulleys and pulley blocks for vehicles of heading 87.11 8483.6091 - - - -Shaft coupling (including Universal Joints) for vehicles of heading 87.11

8483.9020 --- For vehicles of heading 87.11 8484.1022 - - - - Gaskets for water pump, inlet pipe and cylinder block plate for vehicles

of heading 8703.2193

8507.1010 - - - Meant for motor cars of heading 87.03, vehicles of sub-headings 8703.2113, 8703.2115, 8703.2193, 8703.3223, 8704.2190, 8704.3190, 8703.3225 and vehicles of heading 87.11

8511.3010 - - - Ignition Coils for vehicles of heading 87.11 8511.9010 - - - Aluminium casted distributor case for motor cars of heading 8703 (not

exceeding 800cc) and vehicles of sub-heading 8704.3190 8512.2010 - - - Following components of motor vehicles;

(1) Head light for vehicles of sub-headings 8703.2115, 8703.3223, 8703.3225 and vehicles of heading 87.11

(2) Lamp assembly, front turn signal for motor cars of heading 87.03 (not exceeding 1200cc), vehicles of sub-headings 8703.2113, 8703.2115 8703.2193, 8703.3225, 8704.3190 and vehicles of heading 87.11

(3) Lamp assembly for luggage compartment for vehicles of heading 87.03.

Page 7: GOVERNMENT OF PAKISTANengineeringpakistan.com/EngPak1/sro/2006sro693.pdfAct, 1969 (IV of 1969), the Federal Government is pleased to levy additional customs-duty on the import of goods,

7

(4) Lamp assembly for illuminating license plate for motor cars of heading 87.03 and vehicles of sub-headings 8703.2113, 8703.2193, 8703.3223, 8704.2190 and 8704.3190

(5) Rear combination lamp / back up lamp / rear turning indicator / plough lamps / reverse light / parking light for motor cars of heading 87.03 (not exceeding 800cc), vehicles of sub-headings 8703.2113, 8703.2115,8703.3225, 8704.3190 and 87.11

(6) Lamp assembly, side body turning indicator for motor cars of heading 87.03 and vehicles of sub-headings 8703.2113, 8703.2115, 8703.2193, 8703.3223, 8703.3225 and 8704.3190

(7) Turn flasher assembly for motor cars of heading 87.03 (not exceeding 1200 cc) and vehicles of sub-heading 8703.2115; wincking devices for vehicles of heading 87.11

(8) Car ceiling lamp/room lamp for motor cars of heading 87.03 not exceeding 1200cc and vehicles of sub-headings 8703.2113, 8703.2193, 8703.3223, 8704.2190, 8704.3190 and 8703.3225

8512.3010 - - - For vehicles of sub-headings 8703.2113, 8703.2115, 8703.2193, 8703.3225, 8704.2190, 8704.3190 and heading 87.11

8512.4010 - - - (1) Wiper arm and blade assembly for motor cars of heading 87.03 and vehicles of sub-heading 8703.3223, 8703.3225, and 8704.2190

(2) Link assembly for wiper arm and blade for motor cars of heading 87.03 (not exceeding 1200cc) and vehicles of sub-headings 8703.2113, 8703.3223 and 8704.3190

8512.9010 - - - Parts of the products of sub-headings 8512.4010

8532.3010 - - - Capacitor for ignition discharge for vehicles of heading 87.11

8536.5021 - - - - (1) Ignition switches without combination steering lock for motor cars of heading 87.03 (not exceeding 800 cc)

(2) Ignition switches (with or without combination lock) and handle switch assembly for vehicles of heading 87.11

(3) Switch assembly combination and ignition switch assembly for vehicles of heading 8703.2113, 8704.3190;

(4) Door switches for interior lamp for motor cars ofheading 87.03 (not exceeding 1200cc) and vehicles of sub -heading 8704.2190

8537.1010 - - - Fuse boxes 6[with fuses]for vehicles of heading 87.11

8544.3011 - - - - Wiring sets and cable sets for motor cars of heading 87.03, and vehicles of sub-headings 8703.2113, 8703.2115, 8703.2193, 8703.3223, 8704.2190, 8704.3190, 8703.3225 and vehicles of heading 87.11

8544.4221 - - - -Wiring sets and cable sets for motor cars of heading 87.03, and vehicles of sub-headings 8703.2113,8703.2115, 8703.2193, 8703.3223, 8704.2190, 8704.3190, 8703.3225 and vehicles of heading 87.11

8707.1000 - For vehicles of heading 87.03

8707.9010 - - - For vehicles of headings 8704.2190 and 8704.3190

Page 8: GOVERNMENT OF PAKISTANengineeringpakistan.com/EngPak1/sro/2006sro693.pdfAct, 1969 (IV of 1969), the Federal Government is pleased to levy additional customs-duty on the import of goods,

8

8708.1020 - - - (1) Following components for motor cars of heading 87.03 (i) Front and Rear Bumper (cover) (ii) Member/reinforcement for bumpers (iii) Side supports for bumpers

(2) Following components for vehicles of heading 8703.2113 (i) Front and rear bumper (covers) (ii) Stays/ bracket for covers

(3) Front bumper ( sheet metal part ) for vehicles of sub-heading 8703.3223

(4) Front bumper and parts thereof for vehicles of sub -headings 8704.2190 and 8704.3190

(5) Bumpers and parts thereof for vehicles of sub -heading 8703.2115 (6) Front bumpers for vehicles of sub – heading 8703.3225

8708.2110 - - - For motor cars of heading 87.03 and vehicles of sub-headings 8703.2113, 8703.2193, 8703.3223, 8703.3225, 8704.2190 and 8704.3190

8708.2931 - - - - (A) Following components for motor cars of heading 87.03

(1) Air outlet assembly (2) Anchor for spare tyre and parts thereof (3) Apron assembly for front fender and parts thereof (4) Arm rest for door trims (5) Ash trays and parts thereof (6) Battery trays, clamps, bands and parts thereof (7) Bezels for inside 6[door] handles (8) Bottom channel for holding window glass (9) Bracket rear suspension (10) Compartments for floor, rear floor sides, plates side

sills for floor, side lockers for floor (11) Console box assembly and parts thereof (12) Cover assembly for spare wheel and parts thereof

(hard board type) (13) Cover Fuel pipe (for vehicles upto 1200cc) (14) Cross member assemblies for floors and parts thereof

(15) Cross member for roof (16) Cross member/ member front lower, front hood (for vehicles up to

1200cc)

(17) Door assemblies complete (for vehicles not exceeding 800cc) (18) Door checker/ stopper assemblies and parts thereof (19) Door gussets (for vehicles upto 800cc) (20) Door handles inside and parts thereof (21) Door handles outside and parts thereof (22) Door seals for service holes (PE Sheet type) (23) Engine compartment assembly (complete) (24) Engine under covers (dust/ mud/ splash protectors) (25) Extensions for rear floor cross members (26) Floor assemblies ( complete)

Page 9: GOVERNMENT OF PAKISTANengineeringpakistan.com/EngPak1/sro/2006sro693.pdfAct, 1969 (IV of 1969), the Federal Government is pleased to levy additional customs-duty on the import of goods,

9

(27) Fresh air control assembly (for vehicles not exceeding 800cc)

(28) Front floor panels (for vehicles not exceeding1200cc) (29) Front hood assembly (complete) (30) Front radiator grill (non plated) and parts thereof (31) Garnishes and trims (inner/ outer) other than chrome plated

(32) Handles window regulator and parts thereof (33) Heat insulators/ baffles for floor insulation from exhaust pipe

(34) Heating/demisting/ventilation/ defrosting air ducts and nozzles

(35) Housing/ box fuel Inlet (36) Inner panel for windshield header/ rail roof / frame roof assembly (front/

rear) and parts thereof

(37) Inner Panels for quarter window (for vehicles exceeding 800cc but not exceeding 1200cc)

(38) Inner pillars/ reinforcements for side body (39) Instrument panel complete excluding foamed (40) Linings/ guards for fender and wheel housing (41) Link rods for activating door latches (42) Lower cross member for dash panel and parts thereof (for vehicles not

exceeding 1200cc)

(43) Luggage door and parts thereof (hatch back type) (for vehicles not exceeding 800cc)

(44) Member assembly front side with or without apron and parts thereof (for vehicles not exceeding 800cc)

(45) Member cowl and parts thereof (46) Member for engine mounting (for vehicles not exceeding 800cc)

(47) Member steering support and parts thereof (48) Member tail end (for vehicles not exceeding 800cc) (49) Package tray trim/ trim partition (50) Pan rear floor and parts thereof (for vehicles notexceeding 1200cc)

(51) Panel assembly for head lamp support/ mounting and parts thereof

(52) Panel assembly for rear combination lamp mounting and parts thereof

(53) Panel complete rear skirt and parts thereof (54) Panel dash ( sheet metal) (for vehicles not exceeding 1200cc)

(55) Panel dash side (for vehicles not exceeding 1200cc) (56) Panel front fenders (for vehicles not exceeding 1200cc)

(57) Panel grill lower (for vehicles not exceeding 800cc) (58) Panel hood assembly and parts thereof (for vehicles not exceeding

1200cc)

(59) Panel/ Trim assembly for doors and parts thereof except retainers/ clips

(60) Panels rear wheel housing inner) and parts thereof (for vehicles not exceeding 1200cc)

Page 10: GOVERNMENT OF PAKISTANengineeringpakistan.com/EngPak1/sro/2006sro693.pdfAct, 1969 (IV of 1969), the Federal Government is pleased to levy additional customs-duty on the import of goods,

10

(61) Panels door Inner and outer (sheet Metal) front, rear and back (for vehicles not exceeding 800cc)

(62) Panels for cowl and parts thereof, (for vehicles not exceeding 1200cc)

(63) Panels for partition and support to package tray trim /and parts thereof

(64) Panels rear wheel housing inner and outer) and parts thereof (for vehicles not exceeding 800cc)

(65) Panels side body (for vehicles not exceeding 800cc) (66) Parts of instrument panel other than those classifiable under chapter 90

(excluding foamed parts and registers/louvers)

(67) Protective moldings for doors (68) Rails for center roof and reinforcements, assemblies and parts thereof

(69) Rails for roof side and reinforcements, assemblies and parts thereof (for vehicles upto 1200cc)

(70) Reinforcement radiator grill (for vehicles not exceeding 1200cc)

(71) Reinforcements for center floor cross members (72) Reinforcements for strikers and hinges (73) Rod/stay/prop for hood support assembly and parts thereof (74) Roof head lining (except those meant for sunroof) (75) Roof panel complete (for vehicles not exceeding 800cc)

(76) Shroud for fan (77) Side body assembly ( complete) (78) Side member assemblies for rear floors and parts thereof (79) Side members/ reinforcement for main floor and parts thereof

(80) Side sill panel assemblies for main floor, and parts thereof

(81) Silencer/ insulation sheets inner) for dash panel (82) Sound deadening/ insulation/ silencer sheets for floor (83) Strikers for rear seat holding (84) Sun Visor (85) Torsion bars for hinges of luggage compartment (86) Trim door opening (87) Upper front member for hood latch (for vehicles notexceeding 1200cc)

(88) Upper rail/member/frame for back window assembly and parts thereof

(89) Wheel housing mudguards/ mud flaps (B) Following components for vehicles of sub-heading 8703.2113 (1) Anchor for spare tyre and parts thereof (2) Ash trays and parts thereof (3) Battery trays, clamps, bands, box and parts thereof (4) Bottom channel for holding window glass (5) Bracket/ reinforcement/ hangers for suspension (6) Brackets for seat belts (7) Case/ bazel for inside dooe handles

Page 11: GOVERNMENT OF PAKISTANengineeringpakistan.com/EngPak1/sro/2006sro693.pdfAct, 1969 (IV of 1969), the Federal Government is pleased to levy additional customs-duty on the import of goods,

11

(8) Chassis and parts thereof (9) Cross member assemblies for floor and parts thereof (10) Door assemblies (except front door) (11) Door seals for service holes(PE sheet type) (12) Emblems (13) Engine under cover(dust, mud, splash protectors) (14) Floor assemblies (15) Floor mats (16) Frame floor side (17) Frame for front suspension (18) Frame roof front/ plate side and parts thereof (19) Front body (20) Front floor panels and parts thereof (21) Garnish head lamp and centre (22) Garnish, side defroster cover, Control lever (23) Handles, inside pull and parts thereof, except sliding door handles (24) Handles, outside and parts thereof, except sliding door handles

(25) Handles, window regulator and parts thereof (26) Inner pillars/ reinforcements for side body (27) Inner/ outer panel for rear quarter (28) Instrument panel complete, excluding foamed (29) Knob door inside lock (30) Link rods for activating door latches (31) Member floor side (32) Member for engine room (33) Pan rear floor and parts thereof (34) Panel engine room (35) Panel/ trim assembly for doors and parts thereof except retainers/ clips (36) Panels for rear wheel housing (inner) and parts thereof

(37) Parts of instrument panel other than those classifiable under Chapter 90( excluding foamed parts and lid glove box)

(38) Pillar front outer (39) Reinforcements floor side (40) Retainer licence plate (41) Service lid, rear floor (42) Shroud for fan (43) Shut stop for center door (44) Side body assembly (45) Side member assemblies for floor and parts thereof (46) Side sills, front and centre (inner) (47) Sill rear side inner (48) Splash plate for radiator (49) Sun visor (50) Trim rail roof (51) Wheel housing mud guards/ mud flaps

Page 12: GOVERNMENT OF PAKISTANengineeringpakistan.com/EngPak1/sro/2006sro693.pdfAct, 1969 (IV of 1969), the Federal Government is pleased to levy additional customs-duty on the import of goods,

12

(C) Following components for vehicles of sub-heading 8703.2193

(1) Bar for side window (2) Battery trays, clamps, bands and parts thereof (3) Bezels for inside door handles (4) Bracket rear licence plate (5) Carrier for spare tyre and parts thereof (6) Cover assembly for spare wheel (7) Door handles inside/pull and parts thereof (8) Door handles outside and parts thereof (9) Door seals for service holes (PE Sheet type) (10) Duct ventilator/hose defroster (11) Emblems/Stickers (12) Floor mat (plastic) (13) Garnish head lamp (14) Handles window regulator and parts thereof (15) Head lamp support (16) Knob for door lock (17) Mud flaps (18) Panel/ Trim assembly for doors and parts thereof except retainers/ clips

(19) Rod/stay/prop hood support assembly and parts thereof

(20) Service lid rear floor (21) Sound deadning/ insulation/ silencer sheets for floor (22) Stay for radiator support (23) Stay hood lock opener (24) Sun Visor (D) Following components for vehicles of sub-heading 8703.3223

(1) Battery tray assembly and parts thereof (2) Cross member (rear) (3) Door checkers (4) Door handle outside (5) Door handles (inner / outer) (6) Door seals (PE sheet type) (7) Dust cover assembly and parts thereof, for gear change / control lever

(8) End plate (9) Filler neck assembly (10) Floor mat assemblies (11) Front grill / radiator grill (12) Gear box cover assembly for dust / mud protection (13) Gusset plates for engine comportment (14) Heat insulators (15) Heat protector for exhaust manifold (16) Hood cover / soft top (17) Hood sticks

Page 13: GOVERNMENT OF PAKISTANengineeringpakistan.com/EngPak1/sro/2006sro693.pdfAct, 1969 (IV of 1969), the Federal Government is pleased to levy additional customs-duty on the import of goods,

13

(18) Lining for roof (19) Mud covers for engine (20) Mudguard / mud flaps (21) Opener filler lid (22) Pad for Roof Headlining (23) Plastic linings for wheel housing / fender (24) Plate assembly for hand brake mounting (25) Plate holder set for mounting cable for hood opening (26) Reinforcement for bumpers (27) Reinforcements for front floor (28) Reinforcements for roof (sheet metal) (29) Reinforcements for seat belts (30) Reinforcements for storage box / jack box (31) Rod/prop for hood support and parts thereof (32) Side body gussets (33) Side plates for floor (34) Side sills for floor (35) Sound deadening / silencer sheet (36) Stay for fan shroud (37) Stay for radiator (38) Step assembly rear and mounting brackets (39) Sun visor (40) Windshield header panel / Rail (E) Parts and accessories of bodies (including cabs) for vehicles of sub -

heading 8703.2115

(F) Following components for vehicles of sub – heading 8703.3225

(1) Air intake grills for fenders / side grill (2) Bonnet buffer and wind screen staples (3) Centre facia consol assembly (central part of instrument panel) and parts

thereof

(4) Channels for body drain (5) Check link cover (strap) for internal door hinge (6) Cubby box (Console Tunnel base) (7) Door glass holding channel (8) Door Trim (Casing) (9) Emblems (10) Escutcheon (Bazel) for window regulator (11) Escutcheon for sill for lock control (12) Floor mats (13) Gear box tunnel pad (insulation) (14) Handles for tail doors (15) Handles for window regulators (16) Header rails and parts thereof (17) Hood cover (soft top tarpaulin)

Page 14: GOVERNMENT OF PAKISTANengineeringpakistan.com/EngPak1/sro/2006sro693.pdfAct, 1969 (IV of 1969), the Federal Government is pleased to levy additional customs-duty on the import of goods,

14

(18) Hood sticks and parts thereof for soft top mounting (19) Inside handles for doors (20) Lamp guards (21) Lid assembly for locker / storage and parts thereof (22) Locking angle for locker / storage lids (23) Plate assembly for hand brake mounting (24) Radiator grill assembly and parts thereof (25) Rear curtain rod and clamp (26) Rear mud flaps (27) Roll over bar assembly and parts thereof (28) Shedder assembly (PE plastic sheet type) for door insulation (29) Side running board (30) Step assemblies and parts thereof (31) Sun visors

8708.2941 - - - - (A) Following components for vehicles of sub – heading 8704.2190

(1) Ash tray and parts thereof (2) Battery tray and parts thereof (3) Box for tuner (4) Brace for instrument panel (5) Braces for apron (6) Channel assay roof drip (7) Cross members for front floors (8) Deck assembly and parts thereof (9) Door handle outside (10) Door seals (PE sheet type) (11) Door trims (Board type only) (12) Ducts for heater / defroster / ventilation (13) Dust covers (14) Emblems for vehicles (15) Floor mat assemblies (16) Front grill (17) Garnishes (18) Handle for door window mechanism (19) Heat insulators for floor (20) Inner panel for upper back window (21) Inner side members for front floor (22) Lining for roof (23) Louvers for cowl top (24) Louvers for quarter ventilation (25) Mud covers for engine (26) Mudguard (27) Pad for Roof Headlining (28) Plastic linings for wheel housing / fender (29) Plate for rear wheel housing (30) Reinforcement for bumpers

Page 15: GOVERNMENT OF PAKISTANengineeringpakistan.com/EngPak1/sro/2006sro693.pdfAct, 1969 (IV of 1969), the Federal Government is pleased to levy additional customs-duty on the import of goods,

15

(31) Reinforcement for floor panel / member floor side (cab) (32) Reinforcement for instrument panel or member steering support

(33) Rod / prop for hood support (34) Scuff Plates (35) Shroud for fan (36) Side panel for cowl top (37) Sills for floors (38) Sound deadening / Silencer sheet (39) Sun visor (40) Trims for seaming welts (41) Windshield header panel / Rail (B) Following components for vehicles of sub – heading 8704.3190

(1) Ash tray and parts thereof (2) Bars for protection rear glass (3) Cases / Bezels for inside handles (4) Channel for glass door support and rubber thereof (5) Chassis and parts thereof excluding frame rear for floor (6) Cover Frame Floor (7) Cross member assemblies and parts thereof (sheet metal)

(8) Door handles (inside / Outside) (9) Door trims and parts thereof (10) Frame for front floor (11) Frame for front suspension (12) Frame roof front and parts thereof (13) Front / radiator grill and parts thereof (14) Front pillars (inner / outer) and parts thereof (15) Front show and parts thereof (16) Garnishes / Covers / Ventilators and parts thereof (17) Handle for closing deck gate (18) Handle for door window mechanism (19) Holder Jack (20) Instrument panel and parts thereof excluding foamed (21) Insulator for deck floor (sheet metal) (22) Knob for door lock (23) Licence plate, brackets and parts thereof (24) Mat for floor (plastic) (25) Member assemblies for floor and parts thereof (sheet metal) (26) Members, brackets and panels for service lid (27)Mud flaps / mud guards (plastic) (28) Panel / member engine room (29) Panel Cab Back and parts thereof (30) Panel floor front ; floors assemblies and parts thereof (sheet metal) (31) Rear deck and parts thereof (32) Rear Gate and parts thereof

Page 16: GOVERNMENT OF PAKISTANengineeringpakistan.com/EngPak1/sro/2006sro693.pdfAct, 1969 (IV of 1969), the Federal Government is pleased to levy additional customs-duty on the import of goods,

16

(33) Reinforcements for suspension (34) Roof head lining (35) Roof, roof assemblies and parts thereof (36) Seat locks and parts thereof (37) Shroud for fan (38)Side sill (39) Splash panel for engine (40) Splash plate for radiator (41) Sun visor (42) Wheel housing inner and parts thereof

8708.3020 - - - Following components for vehicles of heading 87.03

(1) Brake pedal box assembly and parts, top cover for brake pedal (sheet metal), hand brake lever assembly and parts and brake pipes of vehicles of sub – heading 8703.3225

(2) Brake tubes, pipes and their covers of motor cars of heading 87.03 and vehicles of sub-headings 8703.2113 and 8703.3223

(3) Brakes and parts thereof (excluding brake mastercylinder / pump, actuator and strut) and Mounted brake linings for vehicles of sub heading 8703.2115.

(4) Cable parking brake and parts thereof, of motor cars of heading 87.03 and vehicles of sub-heading 8703.2113

(5) Disc/ drum brake of motor cars of heading 87.03 and vehicles of sub-headings 8703.2113 and 8703.2193

(6) Dust Cover for brake disc of motor cars of heading 87.03 and vehicles of sub-heading 8703.2193

(7) Lever parking brake assembly and parts thereof, of motor cars of heading 87.03 and vehicles of sub-headings 8703.2113, 8703.2193 and 8703.3223

(8) Brake Pedal and housing assembly and parts thereof for motorcars of sub-headings 87.03 and 8703.2193

(9) Brake Pedal assembly and parts thereof; Parking brake cable and parts thereof for vehicles of subheadings 8703.3223

8708.3031 - - - - (A) Following components, of vehicles of sub – heading 8704.2190

(1) Brake Drum (2) Brake tubes (3) Front brake Disc (4) Parking brake cable (B) Following components, of vehicles of sub – heading 8704.3190

(1) Brakes (2) Brake tubes/ pipes (3) Brake drums (4) Lever assembly for parking brake and parts thereof (5) Mounted brake linings (6) Cable assembly for parking brakes, Pedal brake assembly and parts

thereof

Page 17: GOVERNMENT OF PAKISTANengineeringpakistan.com/EngPak1/sro/2006sro693.pdfAct, 1969 (IV of 1969), the Federal Government is pleased to levy additional customs-duty on the import of goods,

17

8708.5020 (1) Built up drive axles for vehicles of sub – heading 8703.2115

(2) Drive shafts for axle, drive shaft housing and breathing pipe for vehicles of sub heading 8703.2115

(3) Built up Non driving axles for motor cars of heading 87.03 (of engine capacity upto 1200cc) and vehicles of sub-heading 8703.2113

(4) Cap spindle for grease and Hub front wheel and trailing / suspension rear arm and parts thereof (for vehicles not exceeding 1200cc) for motor cars of heading 87.03;

(5) Cap spindle for grease for vehicles of heading 8703.2113, 8703.2193; Hub for front axle for vehicle of sub heading 8704.2190;

(6) Cap spindle for grease for vehicles of sub heading 8704.3190

(7) Propeller shaft for vehicles of sub heading 8703.2193

(8) Housing rear axle and propeller shaft for vehicles of sub-heading 8703.2113 and 8704.3190

8708.7010 - - - Road wheels (complete), rims (excluding casted), 5[disc,]caps, ornaments and weights for motor cars of heading 87.03 and vehicles of sub-headings 8703.2113, 8703.2193, 8703.2115, 8703.3223, 8704.2190 and 8704.3190

8708.8010 - - - (1) Suspension Shock absorbers for motor cars of heading 87.03 and vehicles of sub-headings 8703.2113, 8703.2115, 8703.2193, 8704.2190 and 8704.3190

(2) Parts of shock absorber for the vehicle of sub heading 8703.2115

8708.9120 - - - Radiator other than aluminum core, for motor cars of heading 87.03 and vehicles of sub-headings 8703.2113, 8703.2115, 8703.2193, 8703.3223, 8704.2190, 8704.3190, and 8703.3225

8708.9210 - - - Silencers, mufflers and exhaust pipes for motor cars of heading 87.03 and vehicles of sub-headings 8703.2113, 8703.2115, 8703.2193, 8703.3223, 8704.2190, 8704.3190 and 8703.3225

8708.9310 - - - (1) Upper and lower plates for clutch housing (other than clutch plate) of a kind used with engines not exceeding 1200cc for motor cars of heading 87.03 and vehicles of sub-heading 8703.2113 and 8704.3190

(2) Lower plate for clutch housing (other then clutch plate) for vehicles of sub-heading 8703.2193

(3) Arm clutch release for motor cars of heading 87.03 exceeding 1200cc

8708.9410 - - - (1) Steering wheels (non air bag/ non PU foamed type)for motor cars of heading 87.03 not exceeding 1200cc and vehicles of sub-headings 8703.2113, 8703.2193 and 8704.3190; steering knuckle arm left and steering draglink for vehicles of sub heading 8704.2190

(2) Steering gears and links for motor cars of heading 87.03, not exceeding 800 cc

(3) Covers for steering column for motor cars of heading 87.03 and vehicles of sub-heading 8703.2113 and 8704.3190

(4) Steering column for vehicles of sub-heading 8703.2113

(5) Bracket steering gear box for vehicles of sub-heading 8703.2113;

Page 18: GOVERNMENT OF PAKISTANengineeringpakistan.com/EngPak1/sro/2006sro693.pdfAct, 1969 (IV of 1969), the Federal Government is pleased to levy additional customs-duty on the import of goods,

18

(6) steering wheels, steering columns, steering boxes and Steering stem for vehicles of sub - heading 8703.2115

8708.9930 - - - For the vehicles of heading 87.03:

(A) Following components for motor cars of heading 87.03

(1) Air cleaner housing assembly and parts thereof (2) Arms for fan belt adjusting (3) Bracket for generator (4) Bracket for holding jack (5)Bracket for jacking (for vehicles upto 1200cc) (6) Bracket for stabilizing bar (for vehicles upto 1200cc) (7) Bracket front seat inside (for vehicles upto 1200cc) (8) Bracket parking lever (9) Cable assembly for choke and parts thereof (10) Cable for heater / air vent control and parts thereof (for vehicles upto

800cc)

(11) Cable for hood latch release and parts thereof (12) Cables for opening fuel lid and parts thereof (13) Cables for opening trunk latch and parts thereof (14) Cap assembly fuel filler maintenance hole (15) Cap assembly fuel filler (for vehicles upto 800cc) (16) Engine mounting brackets (sheet metal and cast iron, non rubberised) (1 7)Fuel filler neck and pipe (other than plastic) (18) Fuel pipe (main) (19)Fuel pipe (return) (20) Fuel tank (other than plastic) (21) Fuel tank bands / brackets for mounting (22) Fuel tube protectors (for vehicles upto 1200cc) (23) Gear shift control rods/ transmission cables (manualtype) ( for vehicles

not exceeding 1200cc)

(24) Heater unit (using engine heat) and parts thereof (25) Lever fuel lid latch release (26) Lever gear shift control and parts thereof (manual) (27) Lever hood latch release (28) Lever luggage door latch release (29) Lid assembly fuel filler (for vehicles upto 1200cc) (30) Nozzle and hose for wind shield washer (31) Pedal and housing assembly (brake, clutch, accelerator and parts

thereof)

(32) Protectors for fuel filler pipes (33) Protectors fuel tank (34) Reserve tank and hose assembly for radiator tank and parts threreof (35) Seat track adjuster without reclining mechanism (36) Shield fuel tank filler pipe (37) Towing hooks

Page 19: GOVERNMENT OF PAKISTANengineeringpakistan.com/EngPak1/sro/2006sro693.pdfAct, 1969 (IV of 1969), the Federal Government is pleased to levy additional customs-duty on the import of goods,

19

(38) Washer jar (B) Following components for vehicles of heading 8703.2113

(1) Air suction assembly for air cleaner (2) Arm for gear select assembly and parts thereof (3) Arms for fan belt adjusting (4) Bracket for brake fluid reservoir (5) Bracket for fuse box (6) Bracket for generator (7) Bracket for holding jack (8) Bracket for mounting radiator (9) Bracket for suspension (10) Brake fluid reservoir assembly and parts thereof (11) Cable assembly for accelerator and parts thereof (12) Cable assembly for choke and parts thereof (13) Engine mounting brackets (sheet metal and cast iron, non rubberised),

excluding front mount bracket.

(14) Fuel filler neck and pipe (15) Fuel tank (other than plastic) (16) Gear shift control rods/ transmission cables (17) Hanger for muffler (18) Hooks for engine lifting (19) Lever gear shift control and parts thereof (20) Nozzel and hose for wind shield washer (21) Plates, seats, hangers, spring shackle(inner/ outer) bump stoppers, for

use with leaf springs

(22) Reserve tank and hose assembly for radiator water and parts thereof

(23) Spare wheel carrier and bolt assembly (24) Support set for gear shift arm (25) Towing hooks (26) Washer jar ( C ) Following components for vehicles of sub-heading 8703.2193

(1) Arms for fan belt adjusting (2) Engine mounting brackets (sheet metal and cast iron, non rubberised)

(3) Fuel tank (4) Lifting hooks for engine (5) Link rods for activating door latches (6) Nozzel wind shield washer (7) Pedal and housing assembly for brake, clutch, accelerator and parts

thereof

(8) Plate cylinder block (9) Plates, seats, hangers, shackles (inner/ outer), stop rear bump, bumper

rear spring and pad for leaves for use with leaf spring assemblies

(10) Reserve tank and hose assembly for radiator water and parts thereof

Page 20: GOVERNMENT OF PAKISTANengineeringpakistan.com/EngPak1/sro/2006sro693.pdfAct, 1969 (IV of 1969), the Federal Government is pleased to levy additional customs-duty on the import of goods,

20

(11) Washer jar (D) Following components for vehicles of heading 8703.3223

(1) Bands / protective blankets / brackets for fuel tank. (2) Brackets for accelerator cable. (3) Brackets for mounting air cleaner assembly (4) Brackets for mounting bumper (5) Brackets for mounting engine (sheet metal) (6) Brackets for mounting fuse box / relay box (7) Brackets for mounting power steering tank, power steering pump and

power steering oil reservoir

(8) Brackets for mounting radiator (9) Brackets for mounting silencers / mufflers / exhaust pipes

(10) Brackets for mounting suspension (sheet metal) (11) Brackets for mounting vacuum tank (12) Brackets for mudguards (13) Brackets for release mechanism for hood opening (14) Brackets for seats (15) Cable for hood latch release (16) Cable for hood lock control (17) Engine cooling system pipes (metal) (18) Fuel pipe for inlet fuel (19) Fuel tubes, main and return (20) Knobs for seat reclining knuckles (21) Mounting system for spare wheel (22) Oil cooler pipes (metal) (23) Pedal Assembly for accelerator and parts thereof (24) Pedal assembly for clutch and parts thereof (25)Power adjustment screw for hand brake (26) Radiator pipes (27) Resonator for air intake system. (28) Seat Adjusting Track (29) Spare wheel carrier assembly and parts thereof (30) Towing hook (31) Wire protecting pads (foam) (E) Following components for vehicles of sub heading 8703.2115

(1) Air filter assembly and parts thereof (2) Battery carrier assembly and parts thereof (3) Brackets (4) Brake oil tank (5) Breather tube (6) Chassis and parts thereof (7) Control cables assemblies and parts thereof (8) Engine mounting bolt; Engine cover (9) Engine mounting bridge / cross member

Page 21: GOVERNMENT OF PAKISTANengineeringpakistan.com/EngPak1/sro/2006sro693.pdfAct, 1969 (IV of 1969), the Federal Government is pleased to levy additional customs-duty on the import of goods,

21

(10) Fuel pipes (11) Fuel tank assembly and parts thereof; cap fuel tank (12) Fuse box assembly and parts thereof (13) Handle grip (14) Internal cock for handle grip (15) Kick starter assembly and parts thereof (16) Knobs (17) Lever assembly gear shift (18) Sleeve for wheel (19) Spacer for wheel (20) Speedometer cable assembly and parts thereof (21) Torque rod (22) Wheel nuts (F) Following components for vehicles of sub – heading 8703.3225

(1) Accelerator cable (2) Accelerator pedal assembly and parts thereof (3) Air cleaner housing assembly and parts thereof (4) Battery tray assembly and parts thereof (5) Bracket for body floor support (6) Bracket for fuel tank pipes (7) Bracket for mounting body on chassis (8) Bracket for mounting internal light (9) Bracket for power 6[steering] oil reservoir (10) Bracket for power 6[steering] pump mounting (11) Bracket for radiator mounting (12) Bracket for roll over bar (13) Bracket for silencer / exhaust pipe support (14) Bracket for track rod protection (15) Clutch pipe (feed) (16) Cover for fuse box (17) Cradle / support for fuel tank (18) Cyclone pipe oil drain (sheet metal) (19) Flinger / damper (20) Fuel filler cover assembly and parts thereof (21) Fuel filler neck (22) Gate plate for gear lever retention (23) Hose assembly for washer (24) Internal air duct for heater (25) Lower air duct (26) Lower seat for front spring (27) Pipe assembly for fuel and parts thereof (28) Pipe for heater return (29) Retainer for suspension spring (30) Retaining plate for pulley (31) Rings for securing shock absorbers

Page 22: GOVERNMENT OF PAKISTANengineeringpakistan.com/EngPak1/sro/2006sro693.pdfAct, 1969 (IV of 1969), the Federal Government is pleased to levy additional customs-duty on the import of goods,

22

(32) Spare wheel carrier assembly and parts thereof (33) Stay assembly with cover for roll over bar (34) Strap for fuel tank (35) Strut for air cleaner bracket (36) Top plate (plate grommet) for gear change assembly (37) Towing hook (38) Towing ring recovery and lashing assembly and parts thereof

(39) Underside protection bar assembly for propeller shaft (40) Washer tank assembly and cap thereof

8708.9940 - - - Following components for vehicles of heading 87.04:

(A) For vehicles of sub - heading 8704.2190

(1) Air cleaner housing (sheet metal type) (2) Air intake duck for air cleaner assembly (3) Bands / protective blankets / brackets for fuel tank. (4) Cable for hood lock control (5) Clutch Oil Tube (6)Duct snorkel (7) Filler neck assembly (8) Fuel tank (metal type) (9) Fuel tubes, main and return (metallic Type) (10) Heat insulators (11) Jar assembly washer (12) Mounting system for spare wheel (13) Neck assembly for fuel tank (14) Pedal Assembly for accelerator and parts thereof (15) Protector for fuel tank (16) Radiator pipes (17) Reserve tank for radiator (18) Resonator for air intake system. (19) Rods for activating door latches (20) Rods for radiator support (21) Seat Adjusting Track (22) Shackles / shackle plates / pins / hangers for leaf springs (23) Towing hook (24) U bolt for leaf springs (25) Vacuum tank (B) For vehicles of sub - heading 8704.3190

(1) Air suction assembly for air cleaner (2) Arm for gear select assembly and parts thereof (3) Battery box / battery clamp / battery band (4) Battery cover (5) Brackets for brake fluid reservoir, washer tank and water reservoir tank (6) Brackets for fuel box (7) Brackets for mounting alternator

Page 23: GOVERNMENT OF PAKISTANengineeringpakistan.com/EngPak1/sro/2006sro693.pdfAct, 1969 (IV of 1969), the Federal Government is pleased to levy additional customs-duty on the import of goods,

23

(8) Brackets for mounting engine / excluding bracket front mount (9) Brackets for mounting radiator (10) Brackets for mounting rear deck (11) Brackets for mounting 6[steering] gear box (12) Brackets for seat belts (13) Brackets for suspension system (14) Brackets sub - cleaner (15) Brake fluid reservoir assembly and parts thereof (16) Bush spring shackle, shackle plates, bumpers, hangers, stoppers and U

bolts for leaf springs

(17) Cable assemblies for accelerator and choke (18) Emblems (19) Fuel pipes (20) Fuel tank and parts thereof (21) Hooks for lifting engine (22) Lever set for gear shift control (23) Nuts for wheels (24) Pedal Brake, clutch and accelerator assemblies and parts thereof (25) Plate cylinder block (26) Rod / Bracket for tension assembly (27) Rod gear shift select (28) Spare wheel carrier and bolt assembly and parts thereof (29) Stay / Brackets for bumpers (30) Support set for gear shift arm (31) Towing hook (32) Washer jar assembly for wind shield (33) Water reservoir tanks (34)Wind shield washer nozzle assembly

8714.1100 - - Saddles 8714.1910 - - - Following components for vehicles of heading 87.11

(1) Air cleaner assembly and parts thereof (2) Axles (front, rear, collar) and parts thereof (3) Battery Box (4) Bolt for engine mounting (5) Brake cables and parts thereof (6) Brake drums (7) Brake 6[pedal] shaft (8) Brake pads (9) Brake rods, linkages and levers (10) Brake shoes/ Mounted brake lining of asbestos (11) Brakes (complete) (12) Cams for brakes (13) Chain case and parts thereof (14) Clutch cables and parts thereof (15) Complete fuel system

Page 24: GOVERNMENT OF PAKISTANengineeringpakistan.com/EngPak1/sro/2006sro693.pdfAct, 1969 (IV of 1969), the Federal Government is pleased to levy additional customs-duty on the import of goods,

24

(16) Complete wheels (17) Fenders and parts thereof (18) Foot rest and parts thereof (19) Frame / chassis and parts thereof (20) Front fork assembly (complete) (21) Fuel pipes / tubes (22) Fuel tank (whether or not painted) (23) Fuel tank cap (with or without lock) (24) Fuse boxes (25) Gear shift lever pad (26) Grips (whether or not twisting) and parts thereof (27) Handle bar and parts thereof (28)Hubs for wheels (29) Lever set kick starter (30) Levers for front brake and clutch, and parts thereof (31) Motorcycle head lamp housing (32) Mudguards / flaps (plastic) (33) Nipples for wheels (34) Parts for rear shock absorber assembly other than bushes, collars,

stoppers, valves, guides, rings, pistons, rebound, springs, plates and spacers

(35) Parts of front fork assembly other than outer and inner tubes, guides, races, ball assembly, seals, brackets, valves, oil locks, rings, pistons, stoppers, collars, front fork springs, plugs, bridges for forks and seat rebounds

(36) Rear shock absorbers assembly (37) Rim flaps (other than rubber) for wheels (38) Rims for wheels (39) Side covers and parts thereof (40) Side stands / main stands and parts thereof (41) Silencers / exhaust pipes / mufflers and parts thereof (42) Spokes for wheels (43) Sprockets for wheels (44) Swinging arm assembly and parts thereof except collar and bushing (45) Throttle cables and parts thereof (46) Torque link and parts thereof (47) Regulator Rectifier

6[(48) Clutch Assembly]

9026.1020 --- Dipstick/ gauge oil level for engines of motor cars of heading 87.03 and vehicles of sub-headings 8703.2113, 8703.2193, 8703.3225 and 8704.3190

9029.2011 - - - - Mechanical type for motor cars of heading 87.03 (not exceeding 800cc), vehicles of heading 87.11 and vehicles of sub - heading 8704.3190

9032.8910 - - - Temperature control switches for vehicles of sub - heading 8703.2115

9104.0020 - - - (1) For vehicles of sub-heading 8703.3223 (2) For vehicles of sub-heading 8704.2190

Page 25: GOVERNMENT OF PAKISTANengineeringpakistan.com/EngPak1/sro/2006sro693.pdfAct, 1969 (IV of 1969), the Federal Government is pleased to levy additional customs-duty on the import of goods,

25

9401.2010 - - - For motor cars of heading 87.03 and vehicles of sub-headings 8703.2113, 8703.2115, 8703.2193, 8703.3223, 8703.3225, 8704.2190 and 8704.3190

9401.9010 - - - Seat parts made of foam, head/arm rests and seat frames for motor cars of heading 87.03 and vehicles of sub-headings 8703.2113, 8703.2115, 8703.2193, 8703.3223, 8703.3225, 8704.2190 and 8704.3190

9613.8010 - - - Lighters used with motor cars of heading 87.03

Appendix-II

4009.1110 - - - Following components for vehicles of chapter 87 (1) Air cleaner hoses and water cooling system hoses (except turbo system

hoses) for vehicles of sub - heading 8701.2020, 8701.2090, 8701.9040 and 8701.9060

(2) Radiator / engine cooling system hoses and air hoses for vehicles of sub - heading 8701.9020

(3) Air cleaner hoses, vacuum tank hoses and watercooling system hoses (except turbo system hoses) forvehicles of sub - headings 8702.1090 and 8702.9090

(4) Water cooling system hoses (except turbo system hoses) and air cleaner hoses for vehicles of sub - heading 8704.2219

(5) Air cleaner hoses for vehicles of sub – headings 8704.2299 and 8704.2390

4009.2110 - - - Following components for vehicles of chapter 87 (1 ) Air cleaner hoses and water cooling system hoses (except turbo system

hoses) for vehicles of sub – heading 8701.2020, 8701.2090, 8701.9040 and 8701.9060

(2) Radiator / engine cooling system hoses and air hoses for vehicles of sub - heading 8701.9020

(3) Air cleaner hoses, vacuum tank hoses and water cooling system hoses (except turbo system hoses) for vehicles of sub - headings 8702.1090 and 8702.9090

(4) Water cooling system hoses (except turbo system hoses) and air cleaner hoses for vehicles of sub – heading 8704.2219

(5) Air cleaner hoses for vehicles of sub – headings 8704.2299 and 8704.2390

4009.3110 - - - Following components for vehicles of chapter 87 (1) Air cleaner hoses and water cooling system hoses (except turbo system

hoses) for vehicles of sub – heading 8701.2020, 8701.2090, 8701.9040 and 8701.9060

(2) Radiator / engine cooling system hoses and air hoses for vehicles of sub - heading 8701.9020

(3) Air cleaner hoses, vacuum tank hoses and water cooling system hoses (except turbo system hoses) for vehicles of sub - headings 8702.1090 and 8702.9090

(4) Water cooling system hoses (except turbo system hoses) and air cleaner hoses for vehicles of sub – heading 8704.2219

Page 26: GOVERNMENT OF PAKISTANengineeringpakistan.com/EngPak1/sro/2006sro693.pdfAct, 1969 (IV of 1969), the Federal Government is pleased to levy additional customs-duty on the import of goods,

26

(5) Air cleaner hoses for vehicles of sub – headings 8704.2299 and 8704.2390

4009.4110 - - - Following components for vehicles of chapter 87 (1) Air cleaner hoses and water cooling system hoses (except turbo system

hoses) for vehicles of sub – heading 8701.2020, 8701.2090, 8701.9040 and 8701.9060

(2) Radiator / engine cooling system hoses and air hoses for vehicles of sub - heading 8701.9020

(3) Air cleaner hoses, vacuum tank hoses and water cooling system hoses (except turbo system hoses) for vehicles of sub - headings 8702.1090 and 8702.9090

(4) Water cooling system hoses (except turbo system hoses) and air cleaner hoses for vehicles of sub – heading 8704.2219

(5) Air cleaner hoses for vehicles of sub – headings 8704.2299 and 8704.2390

4012.9010 - - - Flaps for use with tyres / tubes for vehicles of sub -heading 8701.2020, 8701.2090, 8701.9040, 8701.9060 and 8704.2219

4016.9920 - - - Following component for vehicles of chapter 87

(1) Cushion / pad sub - assembly for cabin mounting rear member, for vehicles of sub - heading 8704.2219

(2) Cushion for radiator mounting, for vehicles of sub -heading 8704.2299 (3) Mud flaps / mud guards for vehicles of sub – headings 8701.2020,

8701.2090, 8704.2040, 8701.2060, 8702.1090, 8702.9090, 8704.2219, 8704.2299 and 8704.2390

(4) Rubber boots, grommets and dampers, for agricultural tractors of sub - heading 8701.9020

4821.1020 - - - Paper graphics of a kind used for decoration for vehicles of heading 8701.9020

7307.9110 - - - Flanges for air intake pipes for agricultural tractors (upto 80 HP) of sub - heading 8701.9020

7320.1020 - - - For vehicles of sub-headings 8701.2020, 8701.2090, 8701.9040, 8701.9060, 8702.1090, 8702.9090, 8704.2219, 8704.2299 and 8704.2390

7326.9020 - - - Tool box for agricultural tractors of sub – heading 8701.9020

8206.0020 - - - For vehicles of sub-headings 8701.2020, 8701.2090, 8701.9020, 8701.9040, 8701.9060, 8702.1090, 8702.9090, 8704.2219, 8704.2299 and 8704.2390

8302.1020 - - - Of a kind used in doors of vehicles of heading 8704.2299

8302.3020 - - - Window opening mechanism, rack and pinion type for vehicles of sub-heading 8704.2219

8310.0010 - - - Number plate assembly and parts thereof for agricultural tractors of sub-heading 8701.9020

8408.2010 - - - For agricultural tractors of sub - heading 8701.9020 8409.9920 - - - Following other parts of engines for vehicles of Chapter 87:

(1) Inlet or exhaust valves for agricultural tractors of sub - heading 8701.9020

Page 27: GOVERNMENT OF PAKISTANengineeringpakistan.com/EngPak1/sro/2006sro693.pdfAct, 1969 (IV of 1969), the Federal Government is pleased to levy additional customs-duty on the import of goods,

27

(2) Exhaust manifold, inlet manifold, blanking plate / cover, scoop / lube oil reservoir, oil pan / sump with base, bracket rocker shaft, with or without support, tappet cover, timing case, Hub for idler gear and timing cover for agricultural tractors of sub - heading 8701.9020 (excluding 4x4 tractors)

(3) Connecting rod cap, tappets / push rods and rocker arm for agricultural tractors of sub - heading 8701.9020 (upto 80 HP)

(4) Piston assembly and parts thereof and connecting rod for agricultural tractors (upto 55HP) of sub – heading 8701.9020

(5) Rear end housing for agricultural tractors (upto 55HP) of sub - heading 8701.9020

8413.3020 - - - Following parts for Vehicles of sub-heading 8701.9020; (1) Oil pump assembly (2) Water pump for internal combustion piston engines

8421.2320 - - - For vehicles of sub-heading 8701.9020

8428.9010 - - - Hydraulic lift assembly / lift body (other than electronically controlled) for agricultural tractors of sub heading 8701.9020

8481.8010 - - - Cock for fuel tank for agricultural tractors of sub -heading 8701.9020

8483.1011 - - - - Following components for agricultural tractors of sub- heading 8701.9020

(1) Cam shafts (for three cylinder engines only) (2) Counter shaft (3) Crown wheel and pinion (4) Main shaft (5) Pinion constant mesh (6) Pinion counter shaft (3rd) (7) Pinion counter shaft (high) (8) Pinion differential (9) Pinion intermediate (10) Pinion main drive shaft (upto 80 HP) (11) Pinion main shaft inter (12) Pinion PTO ground speed / PTO input (13) PTO shaft assembly (14)Shaft for driven gear (15) Shaft for driving wheel (16) Shaft for hydraulic lift mechanism (17) Shaft for PTO Clutch (18) Shaft for PTO drive (1 9)Shaft for PTO drive gear (20) Shaft for rear drive (upto 80 HP)

8483.4011 - - - - Following components for agricultural tractors of sub- heading 8701.9020

(1) Carrier assembly planetary gears and parts thereof (2) Carrier, rear axle assembly and parts thereof (3) Drive gears PTO (4) Fly wheel rings

Page 28: GOVERNMENT OF PAKISTANengineeringpakistan.com/EngPak1/sro/2006sro693.pdfAct, 1969 (IV of 1969), the Federal Government is pleased to levy additional customs-duty on the import of goods,

28

(5) Gear 3rd / Gear drive 3rd and reverse (6) Gear assembly and gears driven 3rd (7) Gear assembly and gears driven 4th (8) Gear constant mesh / Gear drive 4th (9) Gear drive 1st and 2nd (10) Gear drive Reverse, 1st and 2nd (11) Gear driven 2nd (12) Gear for hydraulic pump drive (for tractors upto 55HP)

(13) Gear ground speed for PTO / Driven Gear for PTO (14) Gear lubricating oil, (for tractors upto 80 HP) (15) Gear main shaft inter and high (1 6)Gear main shaft low / Gear driven 1st (17) Gear PTO constant mesh / Drive gear PTO (18) Gear PTO driven (for tractors upto 55 HP) (19) Gears reverse cluster / gear driven reverse (20) Intermediate gear (for tractors upto 55 HP) (21) Planetary gear (for tractors upto 55 HP) (22) Side gears / differential gears (23) Timing gears ( for three cylinder engines only)

8483.5020 - - - (1) Fly wheels (without built-in gear ring) for vehicles of sub-headings 8701.2020, 8701.2090, 8701.9020, 8701.9040, 8701.9060, 8702.1090, 8704.2219, 8704.2299 and 8704.2390

(2) Fan pulley for vehicles of sub-heading 8701.2020, 8701.2090, 8701.9040, 8701.9060, 8702.1090, 8704.2299 and 8704.2390

(3) Pulleys for crank shaft, alternator and water pump for agricultural tractors of sub - heading 8701.9020

8483.9010 - - - Following components for agricultural tractors of sub-heading 8701.9020 (1) Coupler differential lock/actuating collar (2) Coupler PTO (3) Coupler rear drive (for tractors upto 80 HP) (4) Dog splitter (5) Fork for clutch / lever fork for clutch (6) Fork shifter planetary / Fork splitter (7) Parts for carrier assembly planetary gears (8) Parts for rear axle carrier assembly (9) Planetary coupler / sleeve sliding gear (10) Shifter fork

8484.1021 - - - - Gaskets and joints for agricultural tractors of sub -heading 8701.9020 (excluding 4x4 tractors)

8507.1020 - - - Meant for vehicles of sub-headings 8701.2020,8701.2090, 8701.9020, 8701.9040, 8701.9060, 8702.1090,8702.9090, 8704.2219, 8704.2299 and 8704.2390

8511.4011 - - - -For agricultural tractors of sub - heading 8701.9020 8511.5010 - - - Alternator assembly for agricultural tractors of sub -heading 8701.9020

8511.8010 - - - Heater/glow plugs for agricultural tractors of sub -heading 8701.9020

Page 29: GOVERNMENT OF PAKISTANengineeringpakistan.com/EngPak1/sro/2006sro693.pdfAct, 1969 (IV of 1969), the Federal Government is pleased to levy additional customs-duty on the import of goods,

29

8512.2020 - - - Following parts of motor vehicles;

(1) Head light for vehicles of sub-heading 8701.9020 (2) Lamp assembly, front turn signal for vehicles of sub-heading 8701.9020

and 8704.2219,

(3) Lamp assembly for illuminating license plate for vehicles of sub-heading 8701.9020

(4) Rear combination lamp / back up lamp / rear turning indicator / plough lamps / reverse light / parking light for vehicles of sub-headings 8701.2020, 8701.2090, 8701.9020, 8701.9040, 8701.9060, 8702.1090, 8702.9090, 8704.2219, 8704.2299 and 8704.2390

(5) Lamp assembly, side body turning indicator for vehicles of sub-heading 8701.9020

(6) Ceiling lamp/room lamp for vehicles of sub-heading 8704.2219 8512.3020 - - - For vehicles of sub-headings 8701.9020, 8702.1090 and 8702.9090

8512.4020 - - - Wiper arm and blade assembly for vehicles of sub-heading 8704.2219

8512.9020 - - - Knobs for light switches for agricultural tractors of sub -heading 8701.9020

8536.5022 - - - - Neutral safety switch, push button, ignition switch, light switch, stop light switch, and horn switch for vehicles of sub-heading 8701.9020

8544.3012 - - - - Wiring sets and cable sets for vehicles of sub-headings 8701.2020, 8701.2090, 8701.9040, 8701.9060, 8702.1090, 8702.9090, 8704.2219, 8704.2299, 8704.2390 and 8701.9020

8544.4222 - - - -Wiring sets and cable sets for vehicles of sub-headings 8701.2020, 8702.1090, 8701.2090, 8701.9040, 8701.9060, 8702.9090, 8704.2219, 8704.2299, 8704.2390 and 8701.9020

8707.9090 - - - Other 8708.1010 - - - (1) Bumpers (sheet metal) for vehicles of sub - heading 8701.2020,

8701.2090, 8701.9040 and 8701.9060

(2) Bumper (sheet metal type) and parts thereof for vehicles of sub - headings 8704.2219, 8704.2299 and 8704.2390

8708.2120 - - - For vehicles of sub-headings 8701.2020, 8701.2090, 8701.9040, 8701.9060, 8702.1090, 8702.9090, 8704.2219, 8704.2299 and 8704.2390

8708.2911 - - - - (A) Following components for vehicles of sub-heading 8701.2020, 8701.2090, 8701.9040 and 8701.9060

(1) Battery carrier assembly and parts thereof (2) Cabin tilt stay stopper assembly (3) Cross members for frame (4) Floor mat assembly set (5) Foot steps for cabin entry (6) For 4x2 vehicles: Brackets for shock absorber mounting; Brackets for

mounting engine (casting and sheet metal type) ; Brackets for exhaust pipe; Brackets / support for air and vacuum tank ; Brackets for mounting pedal set ; Brackets assembly for leaf spring assembly (casting) ; Brackets for air cleaner

(7) Frame assembly (8) Gussets / stiffeners for frame

Page 30: GOVERNMENT OF PAKISTANengineeringpakistan.com/EngPak1/sro/2006sro693.pdfAct, 1969 (IV of 1969), the Federal Government is pleased to levy additional customs-duty on the import of goods,

30

(9) Licence plate assembly and parts thereof (10) Long members for frame (4x2 vehicles only) (11) Mounting support for spare wheel carrier (12) Rear body trim (13) Rear member assembly for cabin mounting (14) Shroud for fan (15) Sun visor (B) Following components for agricultural tractors of sub - heading 8701.9020 (1) Battery box assembly and parts thereof (2) Body shield / guard PTO (3) Cowl radiator assembly and parts thereof (4) Fan shroud assembly and parts thereof (5) Fender assemblies and parts thereof (6) Filler neck for lubricating oil (7) Flaps for front hood (8) Foot rest (9) Foot step / foot board assemblies and parts there of (10) Grill assembly / hood cowling assembly and parts thereof

(11) Guard / protector for PTO (12) Heat shields (13) Hood assembly and parts thereof (14) Instrument panels (15) Seat support assembly and parts thereof (16) Side channels (17) Side grill (18) Support for front throttle (19) Warning indicator housing

8708.2920 - - - Following components for vehicles of sub – headings 8702.1090 and 8702.9090

(1 ) Battery carrier assembly and parts thereof (2) Cross members for frame (3) Engine hood and parts thereof (4) Floor assembly and parts thereof (5) Frame assembly (6) Gussets / stiffeners for frame (7) Licence plate assembly (8) Long members for frame (for buses exceeding seating capacity for 35

persons)

(9) Outrigger and meter penal for installing instruments (sheet metal) (10) Roof assembly and parts thereof (11) Shroud for fan (12) Side body assembly and parts thereof

8708.2942 - - - - (A) Following components for vehicles of sub - heading 8704.2219

(1) Battery Carrier assembly and parts thereof

Page 31: GOVERNMENT OF PAKISTANengineeringpakistan.com/EngPak1/sro/2006sro693.pdfAct, 1969 (IV of 1969), the Federal Government is pleased to levy additional customs-duty on the import of goods,

31

(2) Cabin tilt stay stopper assembly and parts thereof (3) Cargo body / deck and parts thereof (4) Cross member for frame (5) Cushion for engine mounting (6) Door trim assembly (Board / PVC type) (7) Emblems (8) Floor mat (9) Frame assembly (10) Front brackets for cabin mounting (11) Front radiator grill (12) Gussets / stiffeners for frame (13) Licence plate assembly (14) Panel for front corner assembly (sheet metal) (15) Rear member assembly for cabin mounting and parts thereof (16) Shroud for fan (17) Splash boards for mud flap mounting (18) Splash covers for engine (19) Sun visors (B) Following components for vehicles of sub – heading 8704.2299 (1) Battery Carrier assembly and parts thereof (2) Cabin tilt stay stopper assembly and parts thereof (3) Cargo body / deck and parts thereof (4) Cross members for frame (5) Door trim assembly (Board / PVC type) (6) Dust protection seal for doors (PE sheet type) (7) Entry steps for cabin (8) Floor mat (9) Frame assembly (10) Gussets / stiffeners for frame (11) Licence plate assembly and parts thereof (12) Long members for frame (13) Rod / Prop / support for bonnet (14) Scuff plates (15) Shroud for fan (16) Splash covers for engine (17) Sun visors (18) Trim for front pillar (C) Following components for vehicles of sub – heading 8704.2390

(1) Battery Carrier assembly and parts thereof (2) Bracket assembly front for cabin mounting (3) Cabin tilt stay stopper assembly and parts thereof (4) Cross members for frame (5) Dust protection seal for doors (PE sheet type) (6) Entry steps for cabin (7) Floor mat

Page 32: GOVERNMENT OF PAKISTANengineeringpakistan.com/EngPak1/sro/2006sro693.pdfAct, 1969 (IV of 1969), the Federal Government is pleased to levy additional customs-duty on the import of goods,

32

(8) Frame assembly (9) Gussets / stiffeners for frame (10) Licence plate assembly and parts thereof (11) Long members for frame (6x2 vehicles only) (12) Member assembly for mounting engine and parts thereof

(13) Rear body trim (other than injection moulded) (14) Rod / prop / support for bonnet (15) Scuff plates (16) Sun visor (17) Trim for front pillar

8708.3010 - - - (A) Following components for vehicles of heading 87.01 (1) Axle shaft assembly for brakes and parts thereof (other than those for disc

brakes) for tractors of sub-heading 8701.9020 (2) Brake assembly for tractors of sub – heading 8701.9020

(3) Brake bands for tractors of sub - heading 8701.9020 (4) Brake drums and air / vacuum tanks for vehicles of sub-heading

8701.2020, 8701.2090, 8701.9040 and 8701.9060

(5) Brake drums and Mounted brake linings for tractors of sub heading 8701.9020

(6) Brake pedal assemblies and parts thereof for tractors of sub - heading 8701.9020

(7) Cam shafts for brake for tractors of sub – heading 8701.9020 (8) Cross shaft assembly and parts thereof for tractors of sub - heading

8701.9020

(9) Brake levers, Brake Pedals, Lever for brake band, Lever for hand brake, Lock combined brakes, Shaft for brake pedals and support for brake lever for tractors of subheading 8701.9020

(10) Lever assembly for parking brake / hand brake (4x2 vehicles only) for vehicles of sub - heading 8701.2020, 8701.2090, 8701.9040 and 8701.9060

(11) Rod and yoke assembly and parts thereof for tractors of sub - heading 8701.9020

(B) Following components for vehicles of heading8702.1090 and 8702.9090 (1) Air tanks and vacuum tanks for brakes (2) Lever assembly for parking brake / hand brake ( for vehicles of seating

capacity less than 35 persons)

(3) Oil/air pipes and brake drums, (4) Brake pedal assembly and parts thereof

8708.3032 - - - - (A) Following components, of vehicles of sub - heading 8704.2219 (1) Air tanks / vacuum tanks (2) Brake drums (3) Lever assembly for parking brake / hand brake (4) Oil and air pipes / tubes (B) Following components, of vehicles of sub – heading 8704.2299

(1) Brake drums

Page 33: GOVERNMENT OF PAKISTANengineeringpakistan.com/EngPak1/sro/2006sro693.pdfAct, 1969 (IV of 1969), the Federal Government is pleased to levy additional customs-duty on the import of goods,

33

(2) Lever assembly for parking brake / hand brake (3) Oil and air pipes / tubes (4) Brake pedal assembly and parts thereof (C) Following components, of vehicles of sub – heading 8704.2390

(1) Brake drums (2) Lever assembly for parking brake / hand brake (3) Oil and air pipes / tubes

8708.4010 - - - Following components for agricultural tractors of sub heading 8701.9020

(1) Gear Boxes

(2) Bottom cover plate for gear box housing (3) Cover / Cup for gear shift lever (4) Cover assembly for drive shift bearing for use in gear box (5) Cover plates for gear box (6) Cover shift tower for gear box (7) Gear box housing (8) Housing for gear shift lever (9) Knob for gear shift lever (10) Lever 3rd and 4th / Fork Third (for gear box) (11) Lever assembly transmission / gear shift lever and parts thereof

(12) Lever for 1st and 2nd gate / gear (13) Lever for reverse gear (14) Lever planetary / lever assembly splitter and parts thereof (15) Plate for mounting gear shift lever (16) Plunger (17) Plunger / dog for gear box (18) Retainer for main drive shaft for use in gear box (19) Rod splitter for gear box (20) Seat for spring for use in gear box (21) Selector 3rd / Gate 3rd and 4th for gear box (22) Selector for planetary shaft / support for splitter for gear box (23) Shaft / fork for clutch release (24) Shift tower for gear box (25) Shift tower for gear box (26) Shifter rails / rods (27) Shifter rails / rods for gear box (28) Supports for splitters (29) Top cover assembly for gear box and parts thereof (30) Shaft for differential lock (31) Shaft reverse/shaft reverse cluster

8708.5010 - - - (1) Built up drive axles with hub and brake drum for vehicles of 'sub - headings 8701.2090, 8702.1090, 8702.9090, 8704.2219, 8704.2299 and 8704.2390

Page 34: GOVERNMENT OF PAKISTANengineeringpakistan.com/EngPak1/sro/2006sro693.pdfAct, 1969 (IV of 1969), the Federal Government is pleased to levy additional customs-duty on the import of goods,

34

(2) Wheel hubs for axles for vehicles of sub headings 8701.2020, 8701.2090, 8701.9040, 8701.9060, 8702.1090, 8702.9090, 8704.2219, 8704.2299 and 8704.2390

(3) Built up drive axles for agricultural tractors of sub-heading 8701.9020 (excluding 4x4 tractors); Bushing PTO sleeve spacer, Cap for differential, Cap for driven axle (for Tractors upto 80HP), Cap for PTO / end cover for PTO, collar for differential lock, collar for PTO, coupler differential lock/actuating collar, coupler rear drive, cover PTO shaft/cover upper axle casing, cover rear axle/side final drive, cover rear axle housing, differential cam lock assembly and parts thereof, differential housing/differential casing/ axle casing, differential lock levers, end assemblies for axles and parts thereof, end assembly for PTO lever, fork for differential locks, fork for PTO clutch, fork PTO and fork PTO clutch, hand lever for PTO clutch, housing for PTO bearings, joint differential cross/journal pinion carrier, internal lever assembly/ lever relay for PTO control and parts thereof, lever for clutch release / shaft for lever clutch, link rocker, pedal assembly for differential lock (for tractors upto 80 hp), pedal for differential control, plate for differential, PTO lever, rear Axle Housing / casing side final drive and parts thereof, Rear cover for PTO, Rear Wheel Hub (for Tractors upto 55HP), Retainer for PTO Bearing, Selector for PTO Control Lever, Shaft assembly for fork lever and parts thereof, Shaft Lock Fork for differential for Agricultural Tractors of sub heading 8701.9020

(4) Built up Non driving axles with hub and brake drums for vehicles of sub - headings 8701.2020, 8701.2090, 8701.9040, 8701.9060, 8702.1090, 8702.9090, 8704.2219, 8704.2299 and 8704.2390 ; Dust protection caps for wheel hubs and Wheel hubs for axles for vehicles of sub heading 8701.2020, 8701.2090, 8701.9040, 8701.9060, 8702.1090, 8702.9090, 8704.2219, 8704.2299, 8704.2390

(5) Built up non driving axles, housing rear axel andpropeller shaft for vehicles of sub-heading 8701.9020; Axlearm for Front Axle, Block pivot for front axle, Block thrustfor axle casing, Cap for front hub/ cover hub, center beamassembly/ body front axle, Drag link assembly/ Tie rods,Hub for front wheel, Pivot pin, Spacer for steering knuckle,Spindle front axle/ Steering knuckle for AgriculturalTractors of sub heading 8701.9020

8708.7020 - - - Road wheels (complete), rims (excluding casted), 5[disc,]caps, ornaments and weights for vehicles of sub-headings 8701.9020, 8702.1090, 8702.9090, 8704.2219, 8704.2299 and 8704.2390 (6x2 vehciles only)

8708.8020 - - - Pin for shock absorbers (4x2 vehicles only) for vehicles of sub headings 8701.2020, 8701.2090, 8701.9040 and 8701.9060

8708.9130 - - - (1) Radiator other than aluminum core, for vehicles of sub-headings 8701.2020 (4x2 vehciles only), 8701.2090, 8701.9040, 8701.9060, 8702.1090, 8702.9090, 8704.2219, 8704.2299, 8704.2390 and 8701.9020

(2) Radiator Cap assembly and parts thereof for Agricultural Tractors of sub heading 8701.9020

8708.9220 - - - Silencers, mufflers and exhaust pipes for vehicles of sub-headings 8701.2020 (4x2 Vehicles only), 8701.2090, 8701.2040, 6[Omitted], 8702.1090, 8702.9090, 8704.2219, 8704.2299, 8704.2390 and 8701.9020

8708.9320 - - - Following parts for agricultural tractors of sub - heading 8701.9020

(1) Clutches (with or without driven plates) (2) Fork for clutch

8708.9420 - - - (1) Steering wheels (non foamed) and Covers Steering shafts for vehicles of sub - heading 8704.2219

Page 35: GOVERNMENT OF PAKISTANengineeringpakistan.com/EngPak1/sro/2006sro693.pdfAct, 1969 (IV of 1969), the Federal Government is pleased to levy additional customs-duty on the import of goods,

35

(2) Steering wheels, steering columns (fixed), steering boxes (manual), Cover for steering column, Cover relay steering box and steering shaft for agricultural tractors of sub - heading 8701.9020

8708.9910 - - - Following components for vehicles of heading 87.01:

(A) For vehicles of heading 8701.2020, 8701.2090, 8701.9040 and 8701.9060 (1) Battery cover (2) Fuel tank (3) Fuel tank bands / supports / brackets / stripes (4) Out side mirror stay assembly (5)Pin for mounting leaf springs (4x2 vehicles only) (6) Retainer / holder for center hearing (4x2 vehicles only) (7) Shackles for leaf spring assembly (8) Stiffener for fly wheel housing (4x2 vehicles only) (9) Towing hooks (10) Upper pad for front leaf assembly (4x2 vehicles only) (B) Following components, of agricultural tractors of sub - heading 8701.9020 (1) Adapter plate / engine mounting bracket (2) Adaptor for techometer drive (for tractors upto 80 HP) (3) Air cleaner housing assembly and parts thereof (4) Air intake pipes / tubes (for tractors upto 80 HP) (5) Anchor for check chain (6)Anchor plate (7) Angle drive (8) Arm for hydraulic lift (9) Arm lift ram for hydraulic mechanism (10) Balls (Cat I and II) (11) Battery retainer assembly and parts thereof (12) Brackets excluding those for throttle control, consol panel and stop light

switch

(13) Cable for tractors meter / hour meter (14) Cam position assembly for hydraulic lift mechanism (15) Cap for lift cover (16) Chain assembly / adjuster lower link and parts thereof (17) Check chain assembly and parts thereof (18) Clutch pedal (19) Collar pre - cleaner / shield air cleaner (for tractors upto 80 HP)

(20) Connecting rod for hydraulic mechanism (21) Control Beam (22) Cooling fan blade (23) Cover lift pump for hydraulics (24) Cover starter motor (25) Deck for fuel tank support (26) Deck for mounting seats (27) Drip tray (28) End implement

Page 36: GOVERNMENT OF PAKISTANengineeringpakistan.com/EngPak1/sro/2006sro693.pdfAct, 1969 (IV of 1969), the Federal Government is pleased to levy additional customs-duty on the import of goods,

36

(29) Exhaust elbow (30) Fork for levelling (31) Front moulding (rubber / plastic) (32) Front tube assembly (33) Fuel cut off cable (for tractors upto 80 HP) (34) Fuel pipes (35) Fuel tank assembly and parts thereof (36) Guard / protection for alternator (37) Head for lubricating oil filter (38) High pressure hydraulic pipe (39) Hook support for top link (40) Hose breather / breather assembly (41) Hub / spacer for fan (42) Knuckle for hydraulic mechanism (43) Leveling assembly shaft and parts thereof (44) Lever and cam assembly for hydraulic lift and parts thereof (45) Lever for alternator / brace stretcher (46) Lever for hand throttle (47) Lever for lift control for hydraulic lift (48)Lever for plough lifting mechanics (49) Lever for relay steering control (50) Lever for response control for hydraulic lift (51) Lever for steering control (52) Lever inner selector for hydraulic lift (53) Lever quadrant cross shaft hydraulic mechanism (54) Lift rod assembly and parts thereof (55) Link assembly control for hydraulic mechanism (56) Link assembly for hydraulic lift (57) Link for pivot pedal (58) Link for PTO clutch (59) Lower link assembly (60) Packing for fuel tank (61) Pad for PTO relay (62) Pads for pedals (63) Parts of fuel sedimentary assembly (64) Pin for beam control (65) Pin for supporting hydraulic mechanism (66) Piston assembly for hydraulic mechanism and parts thereof (67) Pivot shaft for hydraulic lift (68) Plate cover for rear axle (69) Plate draft response for hydraulic lift (70) Plate engine lifting / eye engine lifting (71) Pre cleaner assembly and parts thereof (72) Protection sheet for starter motor (73) Pull rod for stopping engine

Page 37: GOVERNMENT OF PAKISTANengineeringpakistan.com/EngPak1/sro/2006sro693.pdfAct, 1969 (IV of 1969), the Federal Government is pleased to levy additional customs-duty on the import of goods,

37

(74) Quadrant assembly and parts thereof (75) Radiator elbow (76) Response cover assembly for hydraulic lift and parts thereto (77) Retainer for ball (78) Rocker cove (79) Rod / shaft for throttle pedal (80) Sector for draft control (81) Selective assembly and parts thereto (82) Shaft / pin for lower lin (83) Shaft for fuel pump activation (84) Shaft for ram extension (85) Shield for bearing set (86) Shim for fuel tank support (87) Sleeve for lift control (88) Spacer for fuel injection pump (89) Spacer for transmission (90) Spacer rings for fan blades (91) Stand pipe for hydraulic lift mechanism (92) Steering arms (93) Stop reverse shaft (94) Strap for fuel tank (for tractors upto 80 HP) (95) Suction pipe for hydraulic oil (96) Support / bracket for fuel tank (for tractors upto 80HP) (97) Support for foot steps (98) Support for front axle (99) Support for lift pump (100) Support for throttle (101) Support for vacuum pump drive (102) Support for water pump (103) Throttle control (104)Throttle control assembly and parts thereof (for tractors upto 80 HP) (105) Throttle pedal (106) Top link assembly and parts thereof (107) Towing hooks (108) Track rod adjustor (109) Tube assembly for rear axle and parts thereof (110) Water body / elbow water pump (111) Water inlet / water connection (112) Water outlet / pipe outlet (113) Weight for frame (114) Wrapper assembly and parts thereof

8708.9920 - - - Following components for vehicles of sub - headings 8702.1090 and 8702.9090

(1) Accelerator / Brake / Clutch pedal assemblies and parts thereof

Page 38: GOVERNMENT OF PAKISTANengineeringpakistan.com/EngPak1/sro/2006sro693.pdfAct, 1969 (IV of 1969), the Federal Government is pleased to levy additional customs-duty on the import of goods,

38

(2) Air cleaner housing (3) Battery cover (4) Boot for gear shift (5) Brace for adjusting generator / alternator (6) Brackets for mounting air cleaner (7) Brackets for mounting engine (casting and sheet metal) (8) Brackets for mounting exhaust pipes (9) Brackets for mounting leaf springs (10) Brackets for mounting shock absorbers (11) Fuel tank (12) Fuel tank bands / supports / brackets / stripes (13) Hanger for engine lifting (14) Lever and bracket of stabilizer bar (15) Mounting support for spare wheel carrier (16) Pins for mounting leaf springs (17) Retainer / holder for center bearing (18) Shackles for leaf spring assembly (19) Towing hooks (20) U Bolts for leaf springs (21) Upper pad for front leaf spring assembly

8708.9950 - - - Following components for vehicles of heading 87.04:

(A) For vehicles of sub - heading 8704.2219

(1) Air cleaner housing (sheet metal) (2) Air intake pipe and its hood (3) Battery cover (4) Boot for gear shift lever. (5) Brace for adjusting generator / alternator (6) Bracket for mounting air cleaner (7) Bracket helper spring (8) Brackets for leaf springs, shock absorbers, exhaust pipes and engine

mounting (casting and sheet metal)

(9) Fuel tank (10) Fuel tank bands / supports / brackets / stripes (11) Hanger for engine lifting (12) Out side mirror stay assembly (13) Pins for mounting leaf springs (14) Pipe air cleaner to engine (15) Rod assembly for cabin locking mechanism (16) Shackles for leaf springs (17) Stay for cabin entry steps (18) Towing hooks (19) U Bolts for leaf springs (20) Upper pad for front leaf spring assembly (B) For vehicles of sub - heading 8704.2299

Page 39: GOVERNMENT OF PAKISTANengineeringpakistan.com/EngPak1/sro/2006sro693.pdfAct, 1969 (IV of 1969), the Federal Government is pleased to levy additional customs-duty on the import of goods,

39

(1) Accelerator / Brake / Clutch pedal assembly and parts thereof

(2) Air / vacuum tanks for brakes (3) Air cleaner housing assembly and parts thereof (sheet metal) (4) Air intake pipe and its hoods (5) Battery cover (6) Brace for adjusting generator / alternator (7) Brackets for mounting air cleaner, leaf springs, helper springs, shock

absorbers and exhaust pipes.

(8) Brackets for mounting engine (casting and sheet metal) (9) Fuel tank (10) Fuel tank bands / supports / brackets / strips (11) Mounting support for spare wheel carrier (12) Out side mirror stay assembly (13) Pins for mounting leaf springs (14) Retainer / holder for center bearing (15) Shackles for leaf springs assembly (16) Stiffener for fly wheel housing (17) Towing hooks (18) U. Bolts for leaf springs (19) Upper pad for front leaf spring assembly (C) For vehicles of sub - heading 8704.2390

(1) Air / vacuum tanks for brakes (2) Air cleaner housing assembly and parts thereof (sheet metal) (3) Air intake pipe and its hood (4) Battery cover (5) Brace for adjusting generator / alternator (6) Bracket for mounting air cleaner, leaf springs, shock absorbers (6x2

vehicles only), exhaust pipes and air tanks

(7) Brackets for mounting engine (casting and sheet metal) (8) Fuel tank (9) Fuel tank bands / supports / brackets / stripes (10) Hanger for engine lifting (11) Mounting support for spare wheel carrier (12) Out side mirror stay assembly (13) Pins for mounting leaf springs (14) Pipe air cleaner to engine (15) Retainer / holder for center bearing (6x2 vehicles only) (16) Shackles for leaf spring assembly (17) Stiffener for fly wheel housing (6x2 vehicles only) (18) Towing hooks (19) Upper pad for front leaf spring assembly

9025.8030 - - - Temperature gauges and sensors for agricultural tractors of sub - heading 8701.9020

9026.1010 - - - Following parts for agricultural tractors of sub - heading 8701.9020

(1) Fuel gauge

Page 40: GOVERNMENT OF PAKISTANengineeringpakistan.com/EngPak1/sro/2006sro693.pdfAct, 1969 (IV of 1969), the Federal Government is pleased to levy additional customs-duty on the import of goods,

40

(2) Oil level Indicator (3) Dipstick/ gauge oil level for engines

9029.2012 - - - - RPM meter for agricultural tractors of sub – heading 8701.9020

9030.3310 - - - Battery meters for agricultural tractors of sub –heading 8701.9020 9106.1010 - - - Hour meters / tractor meters for agricultural tractors of sub - heading

8701.9020 9401.2020 - - - For vehicles of sub-headings 8701.2020, 8701.2090, 8701.9020,

8701.9040, 8701.9060, 8702.1090, 8702.9090, 8704.2219, 8704.2299 and 8704.2390

9401.9020 - - - Seat parts made of foam, head/ arm rests and seat frames for vehicles of sub-headings 8701.2020, 8701.2090, 8701.9020, 8701.9040, 8701.9060, 8702.1090, 8702.9090, 8704.2219, 8704.2299 and 8704.2390.”

___________________________________________________________________________________________ [C.No. 2(4) II & T-III/06 (Pt)49/2006]

(Shahid Ahmad) Additional Secretary

As amended: 1. S.R.O.1124(I)/2006 - dated 10.11.2006 2. S.R.O.498(I)/2007 - dated 09.06.2007(w.e.f.10.6.2007) 3. S.R.O.767(I)/2007 - dated 02.08.2007 4. S.R.O.561(I)/2008 - dated 11.06.2008(w.e.f.12.06.2008) 5. S.R.O.711(I)/2008 - dated 02.06.2008 6. S.R.O.491(I)/2009 - dated 13.06.2009(w.e.f.14.06.2009)