8
Gefran Software Applications • Small laboratory extruders • Extruders for producing compounds • Extrusion lines for pipes and profiles • Extrusion lines for plastic films and sheets Characteristics • Graphics pages dedicated to machines and extrusion lines • Dynamic configurability of temperature control zones and motors • Management of temperature, current, pressure and preventive maintenance alarms • Closed loop for Melt pressure and control of roller tension • Management of motors in synch • Recipes for work parameters and machine parameters • Configurable trends of process variables • Exportable historical files • Weekly programmer for programmed on/off • Scalability of application on many hardware architectures • Tested solutions based on Gefran Hardware/Software Profile GF_PACK EXTRUSION is Gefran’s solution for complete control of extruders and extrusion lines. GF_PACK EXTRUSION is supplied as preinstalled software on Gefran HW, within which Gefran has inserted a series of preconfigured functions. GF_PACK EXTRUSION consists of standard hardware and software modules: • Operator interface with terminals and Gefran Industrial PCs, 6.5”, 10.4”, 12.1” and 15” colour monitors and touch screen • Gefran GILOGIK II I/O modules with digital and analogue inputs and outputs and temperature sensors • Temperature control modules, Gefran Geflex single loop and multiloop, with on-board SSRs • Application software preconfigured and preloaded on operator interface GF_PACK EXTRUSION contains all typical functions for managing an extruder and an extrusion line. G F PACK EXTRUSION

Gefran Software · Gefran Software Applications ... • Configuration manual with information on source software structure and instructions for ... Intel Celeron Mobile / Frequency

  • Upload
    lamtruc

  • View
    279

  • Download
    7

Embed Size (px)

Citation preview

Page 1: Gefran Software · Gefran Software Applications ... • Configuration manual with information on source software structure and instructions for ... Intel Celeron Mobile / Frequency

0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1

0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1

0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1

0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1

0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1

0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1

0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0

1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1

0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1

0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1

0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0

1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1

GefranSoftware

Applications• Small laboratory extruders• Extruders for producing compounds• Extrusion lines for pipes and profi les• Extrusion lines for plastic fi lms and sheets

Characteristics• Graphics pages dedicated to machines and extrusion

lines• Dynamic confi gurability of temperature control zones and

motors• Management of temperature, current, pressure and

preventive maintenance alarms• Closed loop for Melt pressure and control of roller

tension• Management of motors in synch• Recipes for work parameters and machine parameters• Confi gurable trends of process variables• Exportable historical fi les• Weekly programmer for programmed on/off• Scalability of application on many hardware architectures• Tested solutions based on Gefran Hardware/Software

Profi leGF_PACK EXTRUSION is Gefran’s solution for complete control of extruders and extrusion lines.GF_PACK EXTRUSION is supplied as preinstalled software on Gefran HW, within which Gefran has inserted a series of preconfi gured functions.

GF_PACK EXTRUSION consists of standard hardware and software modules:

• Operator interface with terminals and Gefran Industrial PCs, 6.5”, 10.4”, 12.1” and 15” colour monitors and touch screen• Gefran GILOGIK II I/O modules with digital and analogue inputs and outputs and temperature sensors• Temperature control modules, Gefran Geflex single loop and multiloop, with on-board SSRs• Application software preconfigured and preloaded on operator interface

GF_PACK EXTRUSION contains all typical functions for managing an extruder and an extrusion line.

GF PACKEXTRUSION

Page 2: Gefran Software · Gefran Software Applications ... • Configuration manual with information on source software structure and instructions for ... Intel Celeron Mobile / Frequency

gf_pack extrusion

2

Functions

» Thermoregulation

• Max 96 configurable temperature control zones• Division of temperature control zones into groups• Parameterisation and configuration of temperature control loop from

dedicated application pages• Distributed temperature control with Geflex controllers• Centralized temperature control with GILOGIK II (R-TC8 modules)• Pages with trend graphics on all enabled temperature zones, with acquired

setpoint/value trend

» Motors control and management

• Up to 16 preconfigured motors (extrusion, hopper, mixer, vacuum pump, drag, cut, auxiliary)

• Dedicated pages for motors Start/Stop, with status feedback, from operator panel

• Preconfigured synchronism function activated from operator panel• Automatic management of gear ratio for motors enabled for synchronism• Dedicated pages for scaling analogue input and output values• Pages with trend graphics for all acquired analogue variables• Configuration of up to 4 setpoints on analogue input• Up to 4 closed loops for speed control

As default, machine movement control signals are managed with analogue values (-10 / +10 Vdc).For use of drives in Fieldbus (CANopen) connection, reference values can be managed with read/write on the bus.

» Other functionality

In addition to machine control functions, the packet offers:• Recipe management (exportable via USB port)• Printing of configurable parameters and pages• Videocamera via Ethernet (Netcam) for real time remote control of system

“hot points”• Tele-assistance via modem and Internet• Complete diagnostics of hardware (PLC) with function state and information

on version of configured I/O modules• Multilanguages management with UNICODE support (Italian, English, French,

German, Chinese, etc.)• Password level management for access to pages or change of data items• Easy access to system from local and remote by Ethernet (centralisation,

diagnostics, upgrade)• Availability of a user setting log• Quality control of defined parameters• Programmed system autostart• Counters for managing maintenance of significant data, configurable

runtimes

Page 3: Gefran Software · Gefran Software Applications ... • Configuration manual with information on source software structure and instructions for ... Intel Celeron Mobile / Frequency

gf_pack extrusion

3

The following diagram shows a film extrusion line, highlighting its main functions with specific reference to use of devices in the Gefran catalogue.

Page 4: Gefran Software · Gefran Software Applications ... • Configuration manual with information on source software structure and instructions for ... Intel Celeron Mobile / Frequency

gf_pack extrusion

4

SupplyGF_PACK EXTRUSION is uspplied on a DVD, with which you can install the data and information needed to programme an extrusion line.

The installation DVD contains the following:• User manual with information on functions and operation of pages used to manage an extrusion line• Configuration manual with information on source software structure and instructions for possible changes. A list of available

data/variables and of standard functions is included• General electrical diagram for connecting the operator panel, I/Os and possible connection in case of distributed temperature

control• Graphic utility for guided configuration of structure for passage to various application pages. The utility is also used to configure

access levels for page call

To programme and implement special functions, the development PC requires the configuration tools contained in Gefran Automation Builder (G.A.B.).By using the programming languages you can change the standard functions contained in GF_PACK EXTRUSION to adapt them to specific machine needs.

The information and data on the DVD are subject to a user license that is inserted with the supply.

GF_PACK EXTRUSION is available in various configurations according to the type and complexity of the application:

EXTRULABO

• Application software packet for small/medium extruders• Dynamic pages configurable for up to 16 temperature control zones, up to 3

motors in synch, 1 fast control loop

EXTRUCOMP

• Application software packet for estruders• Dynamic pages configurable for up to 24 temperature control zones, up to 10

motors in synch, 1 fast control loop

EXTRUPIPE

• Application software packet for extruder lines• Dynamic pages configurable for up to 48 temperature control zones, up to 16

motors in synch, up to 4 fast control loops

The various confi gurations (EXTRULABO, EXTRUCOMP and EXTRUPIPE) are matched with one of the terminals of the GF_VEDO ML, GF_VEDO HL or DIGISTAR II series equipped with the VxWorks operating system.The selected terminal is supplied with the OS and selected operative packed preinstalled.

Page 5: Gefran Software · Gefran Software Applications ... • Configuration manual with information on source software structure and instructions for ... Intel Celeron Mobile / Frequency

gf_pack extrusion

5

Technical DataThe automation architecture required for the GF_PACK EXTRUSION solution calls for:

Operator interface based on the following terminals of the GF_VEDO ML series

Operator interface based on the following terminals of the GF_VEDO HL series

Model GF_VEDO ML 65 GF_VEDO ML 104 GF_VEDO ML 121 GF_VEDO ML 150

Type 262K TFT colors

Dimension 6.5” 10.4” 12.1” 15”

ResolutionVGA

(640x480)SVGA

(800x600)SVGA

(800x600)XGA

(1024x768)

Processor Type Geode LX900 / Frequency 600MHz / Core x86

Standard

2 x Ethernet 10/100 Mbps4 x USB 2.0 Host

1 x RS4852 x PS2

1 x TF keyboard

Model GF_VEDO HL 121 GF_VEDO HL 150

Type 262K TFT colors

Dimension 12.1” 15”

ResolutionSVGA

(800x600)XGA

(1024x768)

Processor Type Intel Pentium Celeron - Intel Celeron Mobile / Frequency 600 - 1500MHz

Standard

2 x Ethernet 10/100 Mbps2 x USB 1.1 Host

1 x RS4852 x PS2

1 x TF keyboard

Page 6: Gefran Software · Gefran Software Applications ... • Configuration manual with information on source software structure and instructions for ... Intel Celeron Mobile / Frequency

gf_pack extrusion

6

Gefl ex controllers

Model GFX GFXTERMO4 GFX4

Characteristics1 channel (hot/cold)Solid state relay embeddedDIN rail mounting

4 channels (hot/cold)Solid state relay commandDIN rail mounting

4 channels (hot/cold)Solid state relay embeddedDIN rail mounting

GILOGIK II series remote I/O modules with GDNet (Ethernet) connection to operator interface

Code R-E16 R-U16 R-EU16 R-A/D8R-D/A4R-D/A8

R-MA6 R-TC8 R-C3

Characteristics,Channels number

24Vdc PNP digital inputs 16 8

24Vdc 2APNP digital outputs

16 8 16

mA, V analog inputs,potentiometer, strain gauge (16bit)

8 6

mA, V analog outputs(16bit)

4 - 8 6

Temperature inputs(18bit) (J, K)

8

Counter inputs1

(5KHz)3

(250KHz)

All Input / Output signals are optically isolated.

Page 7: Gefran Software · Gefran Software Applications ... • Configuration manual with information on source software structure and instructions for ... Intel Celeron Mobile / Frequency

gf_pack extrusion

7

Distributed solution

GF_VEDO

GEFLEX

GILOGIK II

Modbus RS485

Centralized control using R-TC8 modules in the GILOGIK II series, with GDNet (Ethernet) connection to operator interface.

Centralized solution

GF_VEDO

GILOGIK IIR-TC8 temperature control

Distributed control using Gefl ex controllers, with serial Modbus connection to operator interface.

Page 8: Gefran Software · Gefran Software Applications ... • Configuration manual with information on source software structure and instructions for ... Intel Celeron Mobile / Frequency

GEFRAN spaVia Sebina, 7425050 Provaglio d’Iseo (BS) - ItalyPh. +39 030 9888.1 - Fax +39 030 9839063Email: [email protected] - Web: www.gefran.com

gf_pack extrusion

Order code

PRECONFIGURED SOLUTIONS

F039561 EXTRULABOApplication software package for small/medium extruders. Dynamically confi gurable up to 16 temperature control loops, up to 3 motor control loops with synchronization and 1 fast closed control loop.

F039562 EXTRUCOMPStandard application software package for extruders. Dynamically confi gurable up to 24 temperature control loops, up to 10 motor control loops with synchronization and 1 fast closed control loop.

F039563 EXTRUPIPEApplication software package for complete extrusion lines. Dynamically confi gurable up to 48 temperature control loops, up to 16 motor control loops with synchronization and 4 fast closed control loops.

SOLUTIONS FOR SYSTEM INTEGRATORS

F039564 EXTRUSYS

Open application software package for complete extrusion lines. Dynamically confi gurable up to 96 temperature control loops, up to 30 motor control loops with synchronization and 10 fast closed control loops. Includes SEVEN programming environment for PLC and HMI, and a 3 days technical training in our laboratories in Provaglio d’Iseo (Italy). (travel and lodgings expenses excluded).

DTS_GF_PACK-EXTRUSION_1209_ENG

Note:The EXTRULABO, EXTRUCOMP, EXTRUPIPE, packages must be ordered together with a DIGISTAR II seriesindustrial PC with VxWorks O.S.