GECKO® SAFETY INSTRUCTIONS & SYMBOLS GUIDE€¦ · The GECKO® PASSION MP 741H/RP 211U wireless system is designed and developed for applications in broadcast studios, theaters,

GECKO® SAFETY INSTRUCTIONS & SYMBOLS GUIDEGECKO® SAFETY INSTRUCTIONS & SYMBOLS GUIDE

For your own safety and to avoid invalidation of the warranty, all text marked with these symbols should be read carefully.

SYMBOLS:SYMBOLS:

SAFETY INSTRUCTIONS:SAFETY INSTRUCTIONS:• To reduce the risk of electrical shock, do not remove covers. No user serviceable parts inside. Please

refer servicing to qualified personnel.• To reduce the risk of electrical shock or fire, do not expose the equipment to rain or moisture.

• Do not impose unnecessary stress on your equipment (i.e. placing heavy objects on it, overscrewing its

mounting etc). • Read and keep the instruction manuals in a safe place for future references.

• Do not attempt to clean the equipment with chemical solvents as this may damage the finish. Clean only

with dry cloth.• Do not block any ventilation openings.

• Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus that

produce heat.• Do not defeat the purpose of the polarized or grounding type plug. A polarized plug has two blades with

one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the grounding prong is provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for the replacement of the obsolete outlet.

• Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles,

and the point where they exit from the apparatus.• Unplug the apparatus during lightning storms or when it is not in use for a long period of time.

NOTESNOTES Contain important information and useful tips on the operation of your equipment.

WARNINGWARNING The lightning flash with arrowhead symbol within an equilateral triangle, is intended toalert the user to the presence of uninsulated dangerous voltage within the product’senclosure that may be of sufficient magnitude to constitute a risk of electric shock.

CAUTIONSCAUTIONSThe exclamation point within an equilateral triangle is intended to alert the user to thepresence of important operating and maintenance (servicing) instructions in thee literature accompanying the appliance. Please read the manual carefully.

HHEADPHONESEADPHONES SAFETYSAFETY WARNINWARNINGGContain important information and useuseful tips on headphones outputs and monitoringlevels.

!

• Use only attachments / accessories specified by the manufacturer.

• Always shut down power supply when not in use to save energy and for prolonged lifespan.

• Exposure to extremely high noise levels may cause permanent hearing loss. Individuals vary

considerably in susceptibility to noise-induced hearing loss, but nearly everyone will lose some hearing if exposed to sufficiently intense noise for a period of time. The U.S. Government’s Occupational Safety and Health Administration (OSHA) has specified the permissible noise level exposures shown in the following chart. According to OSHA, any exposure in excess of these permissible limits could result in some hearing loss. To ensure against potentially dangerous exposure to high sound pressure levels, it is recommended that all persons exposed to equipment capable of producing high sound pressure levels use hearing protectors while the equipment is in operation. Ear plugs or protectors in the ear canals or over the ears must be worn when operating the equipment in order to prevent permanent hearing loss if exposure is in excess of the limits set forth here:

Duration/Day (Hours) dB, Sound Pressure Level (SPL) Descriptions

Below 90dB Safe zone

8.00 90 Hearing damage

6.00 92

4.00 95

3.00 97

2.00 100 Serious hearing damage

1.50 102

1.00 105

0.50 110

0.25 or less 115 Human pain threshold

GECKO MUSIC GROUPGECKO MUSIC GROUP71, Ubi Road 1, #05-34, Oxley BizHub, Singapore 408732.Email: [email protected] • Website: www.geckomusic.net

FOREWORDFOREWORD

Dear Friends,

Thank you very much for purchasing quality products by GECKO MUSIC GROUP. I am indeed very delighted that we have journeyed this far, setting new standards in the audio and music industry while touching and changing lives along the way!

At GECKO MUSIC GROUP we focus on developing nothing but the best professional audio equipment and premium grade musical instruments you ever need! It has been our philosophy all this while that good sound reproductions can be achieved at a fraction of a premium. Our engineering team is constantly doing research and development to meet this objective. We thank God that by HIS grace, we have succeeded in developing the revolutionary C.R.I.S.T.A.L.® Audiophile technology that is changing the way how sound is being encoded, reproduced and managed!

On behalf of GECKO MUSIC GROUP, I would like to pledge our continuing commitment to uphold our traditions in serving music and audio communities around the world with more value-added highest possible quality GECKO® professional audio equipment and premium grade musical instruments!

Once again, thank you very much for your support.

Yours truly,

Daniel Foo Founder / ChairmanGECKO MUSIC GROUP

TABLE OF CONTENTSTABLE OF CONTENTS

INTRODUCTION 1

PACKAGE CONTENTS 2

PASSION RP 211U RECEIVER 4

PASSION MP 741H TRANSMITTER 6

PASSION MP 741H HEADBAND CONDENSER MICROPHONE 9

PASSION CP 2 INTSTRUMENT CONVERTER 10

TIPS FOR OBTAINING BEST RESULTS 11

SPECIFICATIONS 12

WARRANTY 13

NOTES: Congratulations on purchasing the GECKO® PASSION MP741H/RP 211U wireless microphones system! We recommend thatyou take a moment and read through the manual as it providesinformation that will assist you in using your unit to its fullest potential.

______________________________________________________________________________________

© GECKO MUSIC GROUP. All Rights Reserved.

INTRODUCTIONINTRODUCTION

The GECKO® PASSION MP 741H/RP 211U wireless system is designed and developed for applications in broadcast studios, theaters, stage plays, houses-of-worship, corporate AV, schools, concerts, and other live performances. You can also convert your musical instrument into wireless on this system using the included PASSION CP 2 instrument converter cable.

Unwilling to compromise on sound quality, it offers unique uncompressed C.R.I.S.T.A.L.®-clear audio transmission with wide frequency response. It has an average operating time of 16 hours on two AA size alkaline batteries.

Complete System Summary:

32 selectable UHF frequency channels. Extremely linear and crystal-clear vocal transmission with Tone Lock™ technology. 120m range of interference-free signal coverage with Phase-Locked Loop (PLL)™ synthesized technology. Powered by 2 x AA alkaline batteries with 16 hours average battery life. Wide frequency response of 50Hz ~ 15kHz (MP 741H back-electret condenser headband microphone & body-pack transmitter). Provides a wireless solution for most musical instruments via the complementary GECKO® PASSION CP 2 converter cable. Comes with two (2) PASSION MP 741H back-electret condenser headband microphones, two (2) PASSION MP 741H body-pack transmitters, one (1) PASSION RP 211U receiver, two (2) UHF antennas, one (1) PASSION microphone case, one (1) PASSION CP 2 instrument converter cable, one (1) universal power adapter, four (4) 1.5V AA alkaline batteries, and two (2) windscreens.

______________________________________________________________________________________

11


PACKAGE CONTENTSPACKAGE CONTENTS

PASSION MICROPHONE CASE:

PASSION RP 211U RECEIVER:

ROTATABLE UHF ANTENNAS (2):

22


PASSION MP 741H BODY-PACK TRANSMITTERS (2): UNIVERSAL POWER ADAPTER:

PASSION MP 741H HEADBAND CONDENSER MICROPHONES (2): WINDSCREENS (2):

PASSION CP 2 INSTRUMENT CONVERTER CABLE:

**Also includes four (4) 1.5V AA alkaline batteries.

______________________________________________________________________________________

33


PASSION RP 211U RECEIVER PASSION RP 211U RECEIVER

1. ROTATABLE UHF ANTENNASThese are ground independent half-wave omni-directional UHF antennas. Fix the antennas to the female coaxial antenna receptacles [ 2 ] on the receiver. Turn clockwise to secure and counter-clockwise to release. Ensure the antannas are set 90° upright.

2. ANTENNA RECEPTACLESThese are female coaxial antenna receptacles on the receiver's respective CHANNEL A and CHANNEL B.

3. BALANCED XLR OUTPUTSThese are independent balanced XLR male outputs for CHANNEL A and CHANNEL B. Use these balanced outputs for professional applications.

______________________________________________________________________________________

44


FRONT

REAR

4. MIXED A & B OUTPUTThis is CHANNEL A and CHANNEL B stereo summed into a single ¼” TRS audio output. Use this output when you do not have enough channel on your mixing console for independent control of two PASSION wireless microphones.

5. DC INPUTDC input socket for the provided universal power adapter.

6. POWER SWITCHThis digital POWER SWITCH is designed to protect the receiver from start up current spikes that may cause noise and damage to your system. Press and hold the digital POWER SWITCH for 1 second to power ON or power OFF the RP 211U receiver. If you turn off your power supply while the receiver is in ON mode, the receiver will regain its ON mode the next time you turn on the power supply again.

7. LCD DISPLAYThis LCD display will light up when you power up the receiver.

8. RF INDICATOR LEDThis RF indicator LED lights up (red) when you turn ON your PASSION wireless transmitter, indicating the presence of radio frequency (from your transmitter) and that your transmitter is communicating well with your receiver. When this happens, you will also see the RF sign [ 13 ] appearing simultaneously on the LCD display. The RF indicator LED will not light when your transmitter is in the OFF or STANDBY mode.

9. AF INDICATOR LEDThis AF indicator LED lights up (red) when you speak through your PASSION transmitter indicating the presence of audio signal.

10. SET BUTTONTo set your receiver's CHANNEL A and CHANNEL B to your desired channel PRESET FREQUENCY BANK [ 12 ], press the SET button once and one of your channels' PRESET FREQUENCY BANK [ 12 ] will flash, use the UP / DOWN buttons [ 11 ] to select your desired PRESET FREQUENCY BANK for your channel (there are 32 presets of frequency banks per channel: CH1-CH32), to set PRESET FREQUENCY BANK of the other channel, press the SET button again (now the other channel's PRESET FREQUENCY BANK will flash) and repeat the selection process using the UP / DOWN buttons [ 11 ]. When done, leave it flashing for 3 seconds and it will auto save into the receiver's memory.

11. UP / DOWN BUTTONSFor selecting PRESET FREQUENCY BANK on CHANNEL A and CHANNEL B.

12. CHANNEL PRESET FREQUENCY BANKIndicating which PRESET FREQUENCY BANK is on CHANNEL A and CHANNEL B. There are 32 presets per channel: CH1-CH32.

13. RF SIGNIndicating the presence of radio frequency (from your transmitter) and that your PASSION wireless transmitter is communicating well with your receiver. This RF sign will show when your transmitter is in ON and STANDBY mode.

______________________________________________________________________________________

55


14. FREQUENCY VALUESIndicating frequency values in megahertz (MHz). In order for your wireless system to work well, select the same PRESET FREQUENCY BANK (with the same frequency value) for both your receiver and your transmitter.

15. OUTPUT VOLUME CONTROLSTo control output volume for CHANNEL A and CHANNEL B respectively. We recommend setting them at the maximum volume positions at all times.

PASSION MP 741H BODY-PACK TRANSMITTERPASSION MP 741H BODY-PACK TRANSMITTER

16. SINGLE FLEXIBLE UHF ANTENNAFor optimum operating range, always maintain line-of-sight between the transmitter and the receiver whenever possible.

______________________________________________________________________________________

66


16

25

17

18

27

26

24

23

21

20

2219

28

29

30

17. HIGH-IMPACT ABS BODYLightweight high-impact ABS design for longer hours of live applications, reducing handling weight.

18. LCD DISPLAYThe LCD display presents a great deal of setup and operating information clearly and conveniently.

19. RF POWER OUTPUT SWITCHSelect HIGH for long distance transmission. In HIGH mode the trasmitter outputs 30mW of RF power and this uses slightly more battery power. The eight-segment RF bar [ 20 ] appears on the transmitter's LCD display. Select LOW for shorter distance transmission. In LOW mode the transmitter outputs 8.5mW of RF power. The four-segment RF bar [ 20 ] appears on the transmitter's LCD display. We recommend leaving the setting in HIGH position since 30mW is still considerably very low power usage.

20. RF BARShows a full eight-segment bar when transmitter is set to HIGH [ 19 ] output and four-segment bar when set to LOW [ 19 ] output.

21. FREQUENCY VALUESIndicating frequency values in megahertz (MHz). In order for your wireless system to work well, select the same PRESET FREQUENCY BANK (with the same frequency value) for both your receiver and your transmitter.

22. BATTERY LIFE INDICATORAn eight-segment bar indicator. We recommend you replacing the batteries when the bar depletes to three-segment.

23. MINI XLRM AF INPUT SOCKETConnect either one of the supplied PASSION MP 741H headband condenser microphone or the PASSION CP 2 instrument converter cable here.

24. AF INPUT VOLUME LEVELAdjust the gain by turning the control. “+” represents maximum volume or gain, “-” represents minimum volume or gain. Experiment and set for maximum possible gain without audible distortion on the high level peaks.

25. NOISELESS ON / OFF SWITCHDigital switch to prevent startup and shut down “pops”. Press once to power ON, press again to power OFF.

26. LOW BATTERY INDICATORIn the case of dead or low batteries, the LED will either not go on at all or will stay ON (red) continuously, indicating that the batteries should be replaced with fresh ones. ______________________________________________________________________________________

77


NOTES: Turning down the gain too much can compromise the signal-to-noise ratio and is not recommended.

To preserve battery life, turn the transmitter OFF when not in use.

27. CHANNEL UP / SET / DOWN BUTTONSFor selecting PRESET FREQUENCY BANK on your body-pack transmitter. To set your transmitter to your desired channel PRESET FREQUENCY BANK, press the SET button once and the existing PRESET FREQUENCY BANK will flash, use the UP / DOWN buttons to select your desired PRESET FREQUENCY BANK for your transmitter (there are 32 presets of frequency banks per transmitter: CH1-CH32). When done, leave it flashing for 3 seconds and it will auto save into the transmitter's memory. Ensure your transmitter is set to the same PRESET FREQUENCY BANK value as on your PASSION RP 211U receiver's channel for your wireless system to communicate properly.

28. BATTERY COMPARTMENTThe PASSION MP 741H body-pack transmitter uses 2 pieces of 1.5V AA alkaline batteries, with 16 hours of average operating time. Always use good quality fresh alkaline batteries. Do not use rechargeable batteries.

29. BATTERY COMPARTMENT COVERSlight outward to open. Slight inward to close.

30. BELT CLIPThis belt clip can be fixed either upward or downward, depending on your preference. To remove the clip from the body-pack, stretch both sides of the clip outward from its holding holes.

______________________________________________________________________________________

88


PASSION MP 741H HEADBAND CONDENSER MICROPHONEPASSION MP 741H HEADBAND CONDENSER MICROPHONE

The PASSION MP 741H headband condenser microphone provides a uniquely natural and open sound. It is ultra-lightweight and adjustable. The PASSION MP 741H headband condenser microphone ensures a secure and comfortable fit in live performance environments. To ensure optimal performance of your PASSION MP 741H headband condenser microphone, please follow the simple instructions below.

PLACEMENT OF MICROPHONE

______________________________________________________________________________________

99


For discreet placement, you can bend the microphone boom [ 31 ] slightly sothat the capsule [ 32 ] is as close to the cheek as possible. Do not hold thecapsule while bending; bend the wire boom, making a smooth curve with yourthumb to best fit the profile of the face.

The microphone is sensitive to sound from all directions.

The sound remains more or less the same regardless of the distancebetween the sound source and the microphone.

The positioning of microphones with omnidirectional characteristics is lesscritical than with directional.

An omnidirectional microphone is generally not very sensitive to wind,breathing and handling noises.

Omnidirectional Characteristics:

35

32

31

33

33

34

34

36

ADJUSTING THE MP 741H HEADBAND MICROPHONEThe size of the headset mount can easily be adjusted. Change the standard bend by carefully expanding the distance between the earhooks [ 33 ].

To change sides, simply click the boom [ 31 ] out of the clips [ 34 ] and switch it over to the other side.

WINDSCREENS

CABLE MAINTENANCEThe cable [ 35 ] is 1m long. Make sure that superfluous cable is wound up in soft figure-of-eight loops (preferably 6 - 8cm diameter) and avoid kinks in the cable.

Use organic oil (e.g. olive oil) or lukewarm distilled water to remove residue from tape, glue, or make-up on the cable. Do not bend the cable or rub it harshly, it may stress the inner cores of the cable and cause them to break over time.

GENERAL MAINTENANCE The PASSION MP 741H headband microphones are resistant to high levels of humidity. However, care must be taken to keep the headband microphones away from exposure to water and cleaning fluids, and to keep the microphone capsule dry at all times. Do not use spray or use fluid containing chemicals that could remove static electricity on or close to the microphone. This could cause permanent damage.

MINI XLR FEMALE CONNECTORTo provide users with safe and compact mounting of connectors, all headband microphones from GECKO® are fitted with the mini XLR female connector [ 36 ] as standard. Press round lever to release.

PASSION CP 2 INSTRUMENT CONVERTER CABLEPASSION CP 2 INSTRUMENT CONVERTER CABLE

Use this PASSION CP 2 instrument converter cable with your PASSION MP 741H body-pack transmitter to create a wireless system for your musical instrument. Connect the ¼” TS connector into your instrument output.______________________________________________________________________________________

1010


The enclosed windscreens offer additional protection against wind and pop noise.Gently draw the windscreen over the microphone capsule [ 32 ].

For even better protection, bigger windscreens are available.

TIPS FOR OBTAINING BEST RESULTSTIPS FOR OBTAINING BEST RESULTS

1. Use only fresh alkaline batteries. Do not use “general purpose” (carbon-zinc) or rechargeable batteries.

2. Position the receiver so that it has the fewest possible obstructions between it and the normal location of the transmitter. Line-of-sight is best.

3. The transmitter and the receiver should be as close together as conveniently possible, but no closer than three feet (1m).

4. Avoid placing the receiver in a low or shielded location where the transmitter and receiver antennas are not visible to each other. If necessary, use remotely-located receiver antennas.

5. Avoid placing the receiver near computers or other RF generating equipment such as stage LED wall panels, high-power generator or motor, power transformer, TV beamer, and digital TV.

6. The receiver and transmitter must be set to the same frequency.

7. Do not obstruct the handheld transmitter’s antenna (located at the base) or attached body-pack transmitter’s antenna with your hands.

8. You need to change frequencies (a) when a strong interference signal is received, (b) when audio quality is poor due to weak RF, or (c) during multiple-system operation in order to select an interference-free frequency.

9. Turn the transmitter off when not in use. Remove the batteries if the transmitter is not to be used for a period of time.

______________________________________________________________________________________

1111


SPECIFICATIONS SPECIFICATIONS

GECKO® PASSION MP 741H Headband Condenser Microphone

Element: Back-Electret CondenserPolar Pattern: OmnidirectionalFrequency Response: 50Hz ~ 15kHzSensitivity: - 48dB ± 2dBOutput Impedance: ≤ 680ΩNoise Level: ≤ 35dBPower Requirements: 1.5V ~ 10V DCCable Length: 1mOutput Connector: Mini XLR FemaleColor: Light Skin Tone

GECKO® PASSION CP 2 Instrument Converter Cable

Cable Length: 1mOutput Connector: Mini XLR FemaleInput Connector: ¼” TSColor: Black

GECKO® PASSION MP 741H Body-Pack Transmitter:

Frequency Range: 500 ~ 980MHzPreset Channels: 32Oscillation: Phase-Locked Loop (PLL)™ SynthesizedStability: ± 0.005% (0°C ~ 50°C)RF Outputs: 30mW (High), 8.5mW (Low)Frequency Response: 50Hz ~ 15kHz ± 3dBAF Input: Mini XLR MaleDisplay: LCDPower Switch: Digital ON / OFFPower Requirements: 2 x 1.5V AA Alkaline Batteries (≥ 1500mAH)Case Material: High-Impact ABSColor: Metallic GreyWeight: 95g (without Batteries), 145g (with Batteries)Dimension: Body: (H) 90mm x (W) 63mm x (D) 22mm; Antenna: (L) 82mm

GECKO® PASSION RP 211U Receiver:

Frequency Range: UHF-L: 500 ~ 600MHz, UHF-M: 600 ~ 700MHz, UHF-H: 800 ~ 900MHzPreset Channels: 2 x 32Step Down / Step Up Frequency: 0.05MHzFrequency Response: 20Hz ~ 20kHzOutput Connectors: Balanced A / B: XLR Male (2), ¼” TRS Mixed A&B (1)Display: LCDPower Switch: Digital ON / OFFPower Requirements: 12V DC, 600mACase Material: SteelColor: Metallic GreyWeight: 1.60KgDimension: Body: (H) 44mm x (W) 350mm x (D) 158mm; Antenna: (L) 255mm

Included Accessories:

UHF Antennas (2), Universal Power Adapter, 1.5V AA Batteries (4), GECKO® PASSION CP 2 Instrument Converter Cable, Windscreens (2), GECKO® PASSION Microphone Case

Specifications subject to change without prior notice. Manufactured under ISO9000 certified management

system.

______________________________________________________________________________________

1212


Terms of Warranty

GECKO MUSIC GROUP warrants its GECKO® products for a period of three (3) years from the original date of purchase, in accordance to the warranty regulations described below.

What is Covered:

During the applicable warranty period, GECKO MUSIC GROUP warrants the product against defects in materials and workmanship and against malfunctions. GECKO MUSIC GROUP will remedy all such defects and malfunctions without charge for parts or labour if the warranty applies. In the case that other parts are used which constitutes an improvement, GECKO MUSIC GROUP may, at its discretion, charge the customer for the additional cost of these parts. Final determination of warranty coverage lies solely with GECKO MUSIC GROUP.

What is Not Covered:

1. If the product needs to be modified or adapted in order to comply with applicable technical or safety standards on a national or local level, in any country which is not the country where the product was originally developed and manufactured, this modification/adaptation shall not be considered a defect in material or workmanship;

2. Normal wear and tear, in particular, of faders, cross faders, potentiometers, keys/buttons, valves, guitar/bass strings, machine heads, pick-up covers, vinyl covers, illuminants, and similar parts are not covered by this warranty;

3. Improper handling, neglect or failure to operate the unit in compliance with the instructions given in the user or service manuals;

4. Connection or operation of the unit in any way that does not comply with the technical or safety regulations applicable in the country where the product is used;

5. Damages/defects caused by force of nature or any other condition that is beyond the control of GECKO MUSIC GROUP;

6. Any repair or opening of the unit carried out by unauthorized personnel (user included) will void the warranty;

7. Modification or removal of serial numbers.

Obtaining Warranty Service:

To return a GECKO® product for warranty service, first fill out the Online Technical Report on this website and submit for an authorization/service number. Write the authorization/service number so that it is prominently displayed on the outside of the shipping carton. Any products received without an authorization/service number that is clearly visible upon arrival at the factory will be refused. Enclose proof of the original delivery date or a copy of the original sales receipt/invoice. Enclose a description of the suspected defect or malfunction and the condition, if any, which caused the problem. Return the product to either GECKO MUSIC GROUP or the GECKO® Store where the purchase was made.

Warranty Shipping:

You are responsible for prepaying shipping costs F.O.B. GECKO MUSIC GROUP, Singapore. Shipped product(s) must be properly packaged. Use original shipping cartons and packing materials where possible. GECKO MUSIC GROUP is not responsible for damages resulting from inadequate and or improper packing. Products received with damages due to improper packaging will be deemed out of warranty.

Products which do not meet the terms of this warranty will be repaired exclusively at the buyer’s expense. GECKO MUSIC GROUP will inform the buyer of such circumstance. If the buyer fails to submit a written repair order within six (6) weeks after notification, GECKO MUSIC GROUP will return the unit C.O.D. with a separate invoice for freight and packing. Such costs will also be invoiced separately when the buyer has sent in a written repair order.

Warranty Rights:

This warranty is exclusive and extended to the original buyer and is not transferable to anyone who may subsequently purchase this product. No other person (apart from authorized GECKO® Stores) shall be entitled to give any warranty promise on behalf of GECKO MUSIC GROUP.

https://form.jotform.me/91031032044438

Documents

GECKO® SAFETY INSTRUCTIONS & SYMBOLS GUIDE€¦ · The GECKO® PASSION MP 741H/RP 211U wireless system is designed and developed for applications in broadcast studios, theaters,