GCT TAXILA TENDER DOCUMENT - Punjabeproc.punjab.gov.pk/BiddingDocuments/26135_Tender Document.pdf · 1 23 Standard Penetration Test Apparatus ASTM/AASHTO * SPT complete with split

Page 1

2

Flexure / Tension Machine (cement, Mortar, Briquette Tensile Testing)Confirming to ASTM• Automatic Machine 5KN capacity • Application of load by a weight travelling along the beam driven by motor at a constant increasing rate.• Power supply 220V, 50Hz single phase tensile testing jaws, standard briquette mould (two parts construction complete with base plate made of steel, easy collapsible(15Nos)• Complete with all standard accessories

Germany/UK/Japan or Equivalent

1

23

Standard Penetration Test ApparatusASTM/AASHTO* SPT complete with split sample spoon SPT Hammer and drilling rod of 40 - 50 with drilling rod for 40 meters.* SPT sampler consisting of:1) A tube split longitudinally into two parts, the upper end to be fitted to the rod coupling.2) Cutting shoe to be fitted to the lower end.3) Ball valve fitted to rod coupling.* Steel rod 50mm dia, 3000mm long* Nipple for 50mm dia rod* Rod coupling 50mm dia to be fitted to steel rods and upper end of SPT sampler

Germany/UK/Japan or Equivalent

2

Wooden Scaffolding for Mason PAK or EqualiventBattens (5'x3½"x2½") 20Shesham Wood Planks (7'x7"x1½") 30

31Mixing Spoon Setheavy guage stainless steel, 150mm, 200mm, and 250mm long, round buttom

PAK or Equivalent 25

34

Pointing Tray Tampered and hardened steel plate with Wooden handle underneeth* Size = 400x400xthickness 3 m

PAK or Equivalent 20

35 Striker for vertical joint (pointing)Tampered and hardened steel PAK or Equivalent 25

36 Striker for horizontal joint (pointing)Tampered and hardened steel PAK or Equivalent 25

4

PIPE REAMER• High speed steel straight flute, • Parallel hand reamer, left hand spiral, right hand cutting, • 50 mm dia.

UK/Germany/Japan or Equivalent 8

TENDER DOCUMENT

(b) MATERIAL TESTING/SOIL MECHANICS LAB (Concrete, Highway & Soil Mechanics)

QtySpecificationSr #

Total Material Testing LabCONSTRUCTION LAB

27

Total Construction Lab

GCT TAXILA

CIVIL TECHNOLOGY

Unit Rate Total Rate without GST

Total Rate with GST Remarks GST @ 17

%Items with complete specifications

(d) PUBLIC HEALTH ENGINEERING & HYDRAULIC LAB

Page 2


QtySpecificationSr # Unit Rate Total Rate without GST



5

PIPE VICE (STAND TYPE)• Portable , folding pipe vice stand• Tristand vice for ½ -2” (13-50 mm) pipes.• Framework angle iron , • Legs removable G.I pipe 40 mm dia.• Tool tray of sheet steel


7

PIPE THREAD CUTTING KITHigh speed steel, thread cutting die set complete with ratchet die stock , detachable handle and ¼, 3/8, ½, ¾, 1, 1-1/4, 1-1/2, 2” die size, with metal carrying case.

UK/Germany or Equivalent 8

11

COLD CHISEL Set• High carbon hardens steel• Hexagonal/octagonal shank chisels, chrome/black finish, polished cutting edge.

150 mm shank 13 mm wide on cut 300 mm shank 25 mm wide on cut

China/PAK or Equivalent 8

12

STEEL TAPELength 5m, with slide lock, power/automatic return, graduations on both sides in m & ft, plastic / metallic case.

China or Equivalent 16

16

SCREW DRIVER SET• Flat blade, flared tip.• Chrome steel blades/shafts properly tempered and hardened.• Shot blasted tips.• PVC/Polypropylene cabinet handles.One each :Length Blade diamm (in) mm (in) 75 (3) 5 (3/16)100 (4) 6 (1/4)150 (6) 8 (5/16)200 (8) 9.5 (3/8)250 (10) 9.5 (3/8)


17

Trowel (200-280 mm long steel)For general purpose• Tempered and hardened steel.• With wooden handle.

PAK or Equivalent 8

18Mortar Pan • G.I. sheet made (22SWG).• 18” dia., 22 gauge.

PAK or Equivalent 8

19

Shovel with handle9” (225 mm), square / round point, forged steel blade / D-shaped handle wooden 750mm long.

PAK or Equivalent 8

27

MELTING POT• For lead , fitted with lip , handle and legs.• Approximately 150 mm dia. & capacity 16 kg.

PAK or Equivalent 4

28LadleHeavy Forged steel bowl having a lip and long handle, 100 mm dia

PAK or Equivalent 4

29

PIPE YARNING AND CAULKING TOOLSOne picking out, one yarning flat point, one caulking flat point, one yarning hollow point, one caulking flat side cranked; all left and right handed.


Page 3





30

DRAIN CLEANING RODS• Drain rod set comprising of ten rods 915-1000 mm long, double worm screw and plunger and jointed scraper, • made from polypropylene with crimped brass end connections, • complete with special tips (3 Nos.), plastic carrying case with shoulder strap.

PAK/China or Equivalent 2

9 Plotter LaserJet A-0 Size 1

5. Knife Electrician Folding Type 4” Blade. China or Equivalent 7

37 Test and Fault detector Germany/USA/UK or Equivalent 2

66 Thermocouple Wire K type 1600oC China or Equivalent 10

54 Syncroscope 96 x 96 Germany/UK or Equivalent 2

66 Magnet Alnicao U shape China or Equivalent 568 Spring Balance Capacity 50kg Taiwan or Equivalent 2

73 3-Phase Transducer 5kVA variable UK/Germany or Equivalent 1

TOOL BITSMade of high speed steel cobalt alloy hardened and ground

China /Pak or Equivalent

1/2” x 1/2” x 8” or 12x12x100mm 50 - - - - 3/8” x 3/8” x 8” or 10x10x200mm 50 - - - 1/4" x 1/4” x 8” or 6 x6 x63 mm 50 - - -

- - - -

8 Plotter LaserJet A-0 Size Germany/France/Uk or Equivalent 1

11 3pt & 4pt Starter 440V with complete fitting DC motor

Germany/Taiwan/UK or Equivalent 5 - - - -

16 Star Delta Starter 7.5hp-England20 amp-440 v. 3 phase

Germany/Taiwan/UK or Equivalent 5 - - - -

AUTO CAD Lab

Electricity and PLC LAB

Remarks

6

Total BASIC MACHINE SHOP

MECHANICAL TECHNOLOGYSr. No. Description of Equipment Specification Qty

Unit Price Without

GST

Total Price Without

GST 17% of

G.TOTAL WITH

Total Basic Lab No.2

POWER LAB.NO.3

Total Power Lab No.3Grand Total Electrical Technology

Total Rate with GST Remarks

Total Lab No.1

BASIC LAB.NO.2

ELECTRICAL TECHNOLOGYBASIC LAB.NO.1 - WIRING LAB

Sr # Items with complete specifications Specification Qty Unit Rate Total Rate without GST

GST @ 17 %

Grand Total Civil Technology

Total Public Health Lab(e) COMPUTER APPLICATION / AUTO CAD LAB

Total Computer Applications

Page 4





19 Calibrated meter box Germany/Taiwan/UK or Equivalent 4

- - - -

1CUPOLA FURNACE : Upto 1 ton capacity with standard accessories, Blower with installation and working condition

Germany/UK/Japan or Equivalent 1 - - - -

15

CO2 MOLDING APPARATUSCO2 Gas Cylinder with Pressure Regulator Rubber hoses 8 meter, Spray Gun Complete in all respect

Japan/UK/Germany or Equivalent 1 - - - -

31 Strike off BarsWooden, size 1x 2x 20 inch


- - - -

3 FORGING HAMMERS. Germany/UK/France/Japan or Equivalent

7Top and Bottom fullerHardened tool steel with 6 cm 6 cm size and top fuller with handle.

Japan/Uk/Germany or Equivalent 5 - - - -

8 Top and Bottom Swages.Hardened tool steel 6 cm x 6 cm

-do- 5 - - - -

10

Forging / Heating chamberwith blower, Hood etc. Heating by Natural gas bower.Complete Unit.

-do- 2 - - -

- - - -

12Hand ShearManual Type with long handle, 300mm Blade Length


- - - -

20

CIRCULAR PLANE:-Flexible adjustable sole for concave & convex surface iron fastened by means of cam lever locking device, knurled screw & lever for fine depth of cut and lateral adjustments. Width of cutter = 45 mm.Over all length = 260 mm.

UK/Japan/Germany/Taiwan or Equivalent 10 - - - -

22

ROUTER PLANE:-Two knobs for holding, vertical blade adjustment.Blade width = 10-12.Over all length = 38mm

UK/Japan/Germany/Taiwan or Equivalent 5 - -

32

BAR CLAMP:-Made from T-section, back stop is positioned by means a pin through holes in the bar.Jaw opening = 1000 mm.Dimension of Jaw = 50 x 50


40

TRAMMEL:-Polished steel flat rule with guide way, Graduated in mm / inches Adjustable hardened points.Length of beam = 300mm.


C. ARC WELDING

B. FORGING SHOP

WOOD WORK SHOP

Total FOUNDRY SHOPWELDING SHOP

Total Forging Shop:

Total Arc Welding

Total Electricity and PLC LAB

FOUNDRY SHOP

Page 5





46

CENTER BITS:-Round shank with flat contact surface.Diameter = 6, 18, 10, 12 mm.Shank diameter = 5, 6, 6, 7 mm.Overall length = 165, 165, 165, 165mm.Set of 4 pcs

UK/Japan/Germany or Equivalent 5 Set - - - -

- - - -

2

HOOK RULE:-Stainless steel/chromium steel, tempered, hook fitted at zero end, fine quality.Size (mm) = 300.


8

COMBINATION CALIPER:-Made of hardened steel, firm joint, hard point, interchange able pointSize (mm) = 0-300.

-do- 5 - - - -

10MASTER SQUARE:-Made of harden steel, chrome plated. Size (mm) = 150.

-do- 5 - - - -

16

GLASS SURFACE PLATE:-High quality finish. Length x Width x Thickness (mm)=300x300x25

-do- 1 - - - -

19

CUBES:-Made of stainless steel cast iron tool steel. Size (mm) = 50x50x50, 100x100x100.Tolerance (mm) = ± 0.01.

-do- 2 Set - -

25

ENGINEER’S PARALLEL:-Made of tool steel high quality finish. Size (LxWxT)(mm) = 150x12x6, 150x45x30.

-do- 5 - - - -

35

SCREW THREAD MICROMETER:-Carbide tipped face anvil & spindle, shape of anvil and spindle V and Conical.Range (mm) = 0-25.LC = 0.01.

-do- 5 - - - -

45

SINE BAR:- Made of high grade steel chrome finish hardened and ground.Distance between rollers (mm) = 150.

-do- 6 - -

54

ELECTRICAL COMPARATOR:-High precision sensor, stain chrome finish, corrosion resistance, friction free spindle, made of stain less steel, hardened, with two limit contacts.Reading (mm) = 0.005Range (mm) = ±0.13.

-do- 1 - -

55

MECHANICAL COMPARATOR:-Cable release, with probe, mechanism consist of lever, gear segment, friction free, with put backlash, hardened stainless steel with stand,wooden case,instruction manual Reading (mm) = 0. 01.Range (mm) = ±0.25.

-do- 1 - -

- - - -

2 VERNIER CALIPERMeasuring range (mm) = 0-200 LC=0.02

UK/Japan/Germany or Equivalent 20 - - - -

28

SURFACE PLATE:-Made of cast iron, highly polished and flat surface.Width of plate (mm) = 600.Length of plate (mm) = 600Thickness of plate (mm) = 50

UK/Japan/Germany or Equivalent 2 - - - -

METAL WORKSHOP

Total Wood Work ShopMETROLOGY LAB

Total Metrology Lab

Page 6





56

FOOT SHEARStrong Cast and Fabricated BodyShearing width (mm) = 1000Shearing thickness (mm) = 1 mmBack gauge range (mm) = 300

-do- 1 - -

- - - -

Fluid Friction in Pipes with Hydraulic BenchWith VenturimeterThis unit consists of:i. Smooth bore pipes of various diameters (6mm, 10mm and 17mm)ii. An artificially roughened pipeiii. A 90o bendiv. A 90o elbowv. A 45o elbowvi. A 45o “Y”vii. A 90o “T”viii. A sudden enlargementix. A sudden contractionx. A gate valvexi. A globe valvexii. An in-line strainerxiii. A venturi made of Perspexxiv. An orifice meter made of Perspexxv. Pitot Static Tubexvi. Manometers (1m)Experimental Capabilities:• Measurement of pressure loss for laminar and turbulent flow

Thailand/Indonesia/UK or Equivalent - - - -

• Determination of critical Reynold’s numberHead loss measurements using U-tube manometer and mercury U-tube manometerWith all accessories and Instructional Manual COMPLETE AND COMPATABLE IN ALL RESPECTS, , OR EQUIVALENT OF BEST QUALITY.

- - -

MULTI PUMP TEST RIGThe apparatus should be configure on a single bench unit and plug and play type with Built in Service Tank and all accessories.• Built in service tank made of clear acrylic• Close cycle operation• Experiments manual with CDThe apparatus should be comprised of the below mentioned pumps preinstalled and connection.Centrifugal Pump Apparatus• Horizontal single stage pump in clear Plexiglas impeller hosing end suction single volute type• Variable speed control using variable frequency drive• Variable head Control• Inlet and outlet pressure monitoring gauges• Variable area or digital flow meter for pump discharge flow rate measurement


Total Metal Workshop:HYDRAULIC/MATERIAL TESTING

1 1

Page 7





Axial Pump Apparatus• Horizontal single stage pump in clear Plexiglas Impeller hosing• Variable speed control using variable frequency drive• Variable head Control• Inlet and outlet pressure monitoring gauges• Variable area or digital flow meter for pump discharge flow rate measurementReciprocating Pump Apparatus• Horizontal pump in clear Plexiglas pumping head showing all working parts clearly• Variable speed control using variable frequency drive• Variable head feature• Inlet and outlet pressure monitoring gauges• Variable area or digital flow meter for pump discharge flow rate measurementCOMPLETE AND COMPATABLE IN ALL RESPECTS, , OR EQUIVALENT OF BEST QUALITY.

- - -

MULTI TURBINE TEST RIG

The apparatus should be configure on a single bench unit and plug and play type with Built in Service Tank and all accessories.• Close cycle operation• Experiments manual with CDThe apparatus should be comprised of the below mentioned turbines preinstalled with interchangeable DC Dynamometer to use as Generator for load the apparatus should have variable resistive load.

The Control unit should have digital display for speed, Torque & Load.

For inlet and outlet pressure Borden tube manometer should be installed.

For the flow of water variable area or Digital Flow meter should installed with the apparatus.• Variable load, Head, Flow and speed function


5 1

6 1

Page 8




%Items with complete specificationsTransparent turbine construction for operation View for all the turbines

Pelton Turbine

• Number of buckets: 16~18• Nozzle area: variable – 162 mm2 when fully open• Radius of runner to jet impact position: > 56.6 mm• Maximum speed: approximately 1800 rpm• Speed at maximum efficiency (approximately 80%): approx 1200 rpm• Power: 500Watts

Francis Turbine

• Impeller blades: 10~12• Impeller diameter: 100 mm Approx• Impeller inlet height: 14.5 mm Approx• Impeller outlet diameter: 45 mm Approx• Guide varies: six – adjustable, with positioning guidelines

Kaplan Turbine

- - -

Kaplan Turbine

• Inlet height: 14.5 mm• Outlet diameter: 88.0 mm• Interchangeable rotors: three with blade angles of 10º, 20º and 30º, diameters 87 mm• Guide varies: six equi-spaced, diameter 153.4 mmCOMPLETE AND COMPATABLE IN ALL RESPECTS, , OR EQUIVALENT OF BEST QUALITY

- - -

8 Electro pneumatic Trainer 1 SetComplete system consist of following: 1 Set - - - -

Equipment set: (1 No)Training Package: Pneumatics Basic LevelThis training package includes all the components required for training in the fundamentals of pneumatic control technology. Components have the patented Quick Fix mounting system, pneumatic connections on the easily-accessible upper side of the components, and Quick Star fittings for plastic tubing PUN 4 x 0.75 mm with standard inside or outside diameters. All components are industrial quality.The package is supplied in a Systainer with suitable storage containers, which will also fit into Learnline drawers. Also included in the scope of delivery are adhesive symbols which can be used to clearly identify the storage locations of the components.Type: Complete equipment set in the SystainerCOMPLETE AND COMPATABLE IN ALL RESPECTS, , OR EQUIVALENT OF BEST QUALITY.

- - -

Thailand/Indonesia/UK or Equivalent

6 1

Page 9





Compressor: (1 No)Oil-lubricated, extremely quiet (45 dB (A) compressor. Ideally suited for use in classrooms. With pressure regulator and water separator.• Pressure: 800 kPa (8 bar) Pmax • Performance: 50 l/min • Reservoir capacity: 24 l • Compressed air outlet: ¼“ • Noise level: 45 dB (A)/1 m • Continuous operation: max. 50%.COMPLETE AND COMPATABLE IN ALL RESPECTS, , OR EQUIVALENT OF BEST QUALITY.

- - -

Compressor accessories: (1 No)Consisting of: • Coupling socket (KD3-CK-4 and KD4-1/4-A) • Coupling plug (KS4-CK-4) • Tubing (6 x 1 silver 2,5 m)COMPLETE AND COMPATABLE IN ALL RESPECTS, , OR EQUIVALENT OF BEST QUALITY

- - -

Accessory box: (1 No)The accessory box contains pneumatic connectors and tubing accessories as well as a tubing cutter and releasing tool for pneumatic connectors.COMPLETE AND COMPATABLE IN ALL RESPECTS, , OR EQUIVALENT OF BEST QUALITY.

- - -

Pneumatics Basic Level: Training course documents (1 No)Nineteen project-orientated exercises, increasing in complexity and suitable for equipment set are the ideal introduction to pneumatics. Real problem descriptions with positional sketch, concrete project tasks and detailed aids for professional implementation provide the ideal preparation for real-life industrial environment. A new feature in the latest edition is the separation of the documentation into a workbook and a book of exercises. Each worksheet in the book of exercises has a sample solution in the workbook.COMPLETE AND COMPATABLE IN ALL RESPECTS, , OR EQUIVALENT OF BEST QUALITY.

Page 10





Software: (1 No)FluidSIM®4.2 Pneumatics, individual and multiple licenses FluidSIM® Pneumatics contains a circuit diagram generation tool, a high-performance simulation tool and an e-learning tutorial on the subject of pneumatics, electro pneumatics, digital technology and GRAFCET. COMPLETE AND COMPATABLE IN ALL RESPECTS, , OR EQUIVALENT OF BEST QUALITY.System requirements • PC with Windows 98/ME/NT/2000/XP/Vista/Windows 7 • At least Pentium II 500 MHz • At least 128 MB RAM • Sound card • 4-speed CD-ROM drive Number of pieces: Single/x-license Type license: Network Version (language): ENCOMPLETE AND COMPATABLE IN ALL RESPECTS, , OR EQUIVALENT OF BEST QUALITYCD-ROM: (1 No)FluidSIM®4.2 Pneumatics –Student version Fluid SIM Pneumatics contains a circuit diagram generation tool, a high-performance simulation tool and an e-learning tutorial on the subject of pneumatics, electropneumatics, digital technology and GRAFCET.COMPLETE AND COMPATABLE IN ALL RESPECTS, , OR EQUIVALENT OF BEST QUALITY. System requirements • PC with Windows 98/ME/NT/2000/XP/Vista/Windows 7 • At least Pentium II 500 MHz • At least 128 MB RAM • Sound card • 4-speed CD-ROM drive COMPLETE AND COMPATABLE IN ALL RESPECTS, OR EQUIVALENT OF BEST QUALITY.

Page 11





Differences between full and Limitations of student version: In comparison with the student version, the full version offers the following functions: • Simulation of complex circuits without limitation limiting the number of components.• Precise calculation of pressures, flow rates, speeds, cylinder forces, electrical currents and voltages • Display of calculated status variables at all connections or by installing measuring instruments • Status diagrams for graphical display of simulation values during simulation • DXCF import and export • Expanded component library • Configurable valves • Configurable cylinders • Proportional and closed-loop-control technology CD-ROM:FluidSIM®4.2 Pneumatics –Student version Fluid SIM Pneumatics contains a circuit diagram generation tool, a high-performance simulation tool and an e-learning tutorial on the subject of pneumatics, electropneumatics, digital technology and GRAFCET.COMPLETE AND COMPATABLE IN ALL RESPECTS, , OR EQUIVALENT OF BEST QUALITY. System requirements • PC with Windows 98/ME/NT/2000/XP/Vista/Windows 7 • At least Pentium II 500 MHz • At least 128 MB RAM • Sound card • 4-speed CD-ROM drive COMPLETE AND COMPATABLE IN ALL RESPECTS, OR EQUIVALENT OF BEST QUALITY.Differences between full and Limitations of student version: In comparison with the student version, the full version offers the following functions: • Simulation of complex circuits without

- - -

Software: (1 No)Training software Fundamentals of pneumatics The interactive and multimedia training program covers the basics of pneumatic control systems. Content extracts: • Drive components • Power supply • Final control elements • Signaling elements • Control elements • Additional requirements Training time: approx. 12 hours E.g. Single license on CD-ROM: with network license connector DE/EN/ES/FRCOMPLETE AND COMPATABLE IN ALL RESPECTS, , OR EQUIVALENT OF BEST QUALITY.

- -

Page 12




%Items with complete specificationsEquipment set, (1 No)Extension kit to convert "Pneumatics, Basic Level" to "Electropneumatics, Basic Level"This extension kit, together with the equipment set "Pneumatics, Basic Level", provides all the components required for basic training in electropneumatic control technology. Components have the patented Quick-Fix system, pneumatic and electrical connections are located on the easily-accessible upper side of the components, Quick Star fittings for plastic hose PUN-4 x 0.75 with standard inside or outside diameters and 4 mm safety sockets or M8 industrial plug connectors. All components are of industrial quality. Supplied in a Systainer with suitable storage containers, also suitable for Learnline storage drawers. The scope of delivery also includes adhesive symbols to clearly identify the storage location of each component. Complete supplementary equipment set in the Systainer COMPLETE AND COMPATABLE IN ALL RESPECTS, , OR EQUIVALENT OF

- - -

Connecting cable set, (1 No)Safety laboratory cables, 98 units, red and blue Complete set, consisting of 98 safety laboratory cables with 4 mm safety connectors in the colors red and blue: • 10x red 50 mm • 10x blue 50 mm • 26x red 300 mm • 11x blue 300 mm • 21x red 500 mm • 12x blue 500 mm • 3x red 1000 mm • 3x blue 1000 mm • 1x red 1500 mm • 1x blue 1500 mmCOMPLETE AND COMPATABLE IN ALL RESPECTS, , OR EQUIVALENT OF BEST QUALITY.

- - -

Edutrainer, (1 No)Power supply unit for mounting frame• Input voltage: 85 – 265 V AC (47 – 63 Hz) • Output voltage: 24 V DC, short-circuit-proof• Output current: max. 4.5 A • Dimensions: 170 x 240 x 92 mm• Mains cable: Without power cableCOMPLETE AND COMPATABLE IN ALL RESPECTS, , OR EQUIVALENT OF BEST QUALITY.

- - - -

Page 13




%Items with complete specificationsTeachware, (1 No)Electropneumatics Basic Level: Training course documents Twelve project-orientated exercises, increasing in complexity and suitable for equipment set, are the ideal introduction to electropneumatics. Real problem descriptions with positional sketch, concrete project tasks and detailed aids for professional implementation provide the ideal preparation for a real-life industrial environment. A new feature in the latest edition is the separation of the documentation into a workbook and a book of exercises. Each worksheet in the book of exercises has a sample solution in the workbook. Workbook• Sample solutions• Training notes• Multimedia CD-ROM with graphics, photos of industrial applications, animations and FluidSIM® circuit diagrams• 144 pages, in color, bound • Additional book of exercises as sample Book of exercises for students• WorksheetsSoftware, (1 No)Training software Fundamentals of electropneumaticsThe interactive and multimedia training program covers the basics of electropneumatic control systems. This knowledge will be implemented in the project section using various practical projects. The participants can refer back to the project-specific information contained in the sections on technical knowledge and component knowledge during the project.

Content extracts:• Advantages and drawbacks of electropneumatics• Fundamentals of electricity• Components of electropneumatics• Electromechanically actuated valves • Relays and contactors• Basic circuits• Direct and indirect actuation• Basic logic functions• Various sequence controllers• Standards-compliant electrical circuit diagrams• Electrical and pneumatic circuit diagrams• Safety and protective measures in electropneumatic systems• Maintenance and servicing including fault location and elimination• Standards-compliant documentation of electropneumatic circuitsTraining time: approx. 12:00 hoursE.g. Single license on CD-ROM: with network license connector DE/EN/ES/FRCOMPLETE AND COMPATABLE IN ALL RESPECTS, , OR EQUIVALENT OF BEST QUALITY.

Page 14





Magnet Symbol Set, (1 No)For step-by-step development of circuit diagrams. The symbols adhere to a metal-backed board. Connections and designations are marked with chalk. The symbol sets are stored in a Systainer.Design: Electrical engineeringCOMPLETE AND COMPATABLE IN ALL RESPECTS, , OR EQUIVALENT OF BEST QUALITY.

- - -

Video film, (1 No)DVD Electropneumatics and Electrohydraulics, Basic LevelThe main emphasis of this DVD is on electrical control systems. In addition to an introduction to electrical engineering, it shows the most important circuit components and basic circuits. Practical applications are shown interspersed with animations and examples of circuits. The film has soundtracks in the languages DE, EN, ES, FR, IT, TR, CN and RU. Users can select the desired language. The DVD has a running time of 48 minutes and is supplied packed in a Systainer.COMPLETE AND COMPATABLE IN ALL RESPECTS, , OR EQUIVALENT OF BEST QUALITY.

- -

Equipment set, (1 No)Training Package: Electro pneumatics, Advanced LevelThis training package contains all the components required for advanced training in electro pneumatic control engineering, It builds on Training Package Components have the patented Quick-Fix system, pneumatic and electrical connections are located on the easily-accessible upper side of the components, Quick Star fittings for plastic hose PUN-4 x 0.75 with standard inside or outside diameters and 4 mm safety sockets. All components are of industrial quality. Supplied in a Systainer with suitable storage containers, also suitable for Learn line storage drawers. The scope of delivery also includes adhesive symbols to clearly identify the storage location of each component. Type: Complete equipment set in the SystainerCOMPLETE AND COMPATABLE IN ALL RESPECTS, , OR EQUIVALENT OF BEST QUALITY.

- -

Page 15




%Items with complete specificationsTeachware, (1 No)Electropneumatics, advanced level: Training course documents As a continuation of the basic level for electropneumatics, the advanced level includes twelve additional, challenging tasks which are suitable for the equipment set. The documents are targeted at experienced pneumatics technicians. New features of this revised and updated edition include revised exercise sheets for practical use during instruction. The workbook contains a sample solution for each of the exercise sheets. The workbook includes:• Sample solutions• Training notes• Multimedia CD-ROM with graphics, photos of industrial applications, animations and FluidSIM® circuit diagrams• Exercise sheets for trainees• 298 pages, colour, in binderM. Pany, S. Scharf, R.-C. Weber Edition 2010Version (language): Workbook EN COMPLETE AND COMPATABLE IN ALL RESPECTS,(ALONGWITH

- -

10

Hydraulic Trainer (Transparent Type Components)Consisting of following items ( complete in all respect) (1 each)

Thailand/Indonesia/UK or Equivalent

1Each - - - -

• Transparent model table Size: 1500(L) x 790(W) x 870(H)mmCabinet (Locking type)430 (L) x 700 (W) x 680(H)mmInside 360x620mmTransparent model socket panel

- -

• Transparent model power unitCapacity: 7.5 lHydraulic oil: ISO VG32Motor: AC220V, 60HzMax Pressure: 10kg/cm2Hydraulic pump

- -

• Hydraulic transparent model clampUsed for fixing parts on the OHPPlastic clamp

- -

• Pressure relief valve, directly controlledLength: 75mmWidth: 60mm2 portAdjusting lever operated

- -

• Pressure relief valve, cushion, directly controlledLength: 75mmWidth: 60mm2 portAdjusting lever operated

- -

• Pressure reducing valveLength: 75mmWidth: 60mm3 portSpring adjustableAdjusting lever operated

- -

Page 16





• 2 way flow control valve Length: 75mmWidth: 60mm2 portAdjusting lever operated

- -

• Orifice valve Length: 75mmWidth: 60mm2 porthand lever operated

- -

• One way flow control valveLength: 75mmWidth: 60mm2 portAdjusting lever operatedSpring check type

- -

• Pressure compensative flow control valveLength: 75mmWidth: 60mm3 portAdjusting lever operatedSpring spool type Inside pressure measurement

- -

• Hydraulic check valveLength: 75mmWidth: 60mm2 portSpring check type

- -

• Hydraulic check valve, pilot actuatedLength: 75mmWidth: 60mm3 portSpring spool type

- -

• 2/2 way valveLength: 75mmWidth: 60mm2 portHand lever operated

- -

• 3/2 way valve Length: 75mmWidth: 60mm3 portHand lever operated

- -


- -


- -

• Hydraulic double acting cylinder Length: 75mmWidth: 60mm2 portPiston dia: 15mmStroke 50mm

- -

• 5/2 way valve, pilot actuatedLength: 95mmWidth: 60mm5 portPush lever operated

- -

Page 17





• Shut-off, circuitLength: 95mmWidth: 60mm4 portAdjusting lever operated Spring check type

- -

• Pressure relief valve, pilot actuatedLength: 80mmWidth: 60mm4 portAdjusting lever operated Spring spool type

- -

• Pressure relief valve, externally actuatedLength: 80mmWidth: 60mm4 portAdjusting lever operated Spring spool type

- -

• Double check valve, pilot actuatedLength: 95mmWidth: 60mm4 portSpring spool type

- -

• Flow dividing valve Length: 75mmWidth: 60mm4 portAdjusting lever operated Spring spool type

- -

• 3 way pressure flow control valveLength: 95mmWidth: 60mm3 portAdjusting lever operated Spring spool type

- -

• Rectifier circuit Length: 90mmWidth: 90mm4 portSpring check type 4 check valves

- -

• Vane motorLength: 90mmWidth: 90mm2 port

- -

• Internal gear motor Length: 90mmWidth: 90mm2 port

- -

• External gear motor Length: 90mmWidth: 90mm2 port

- -

• Linear motorLength: 90mmWidth: 90mm2 port• Rotary vane motorLength: 90mmWidth: 90mm2 port• Axial piston motor Length: 110mmWidth: 60mm4 port

Page 18





• Pressure gaugeLength: 50mmWidth: 50mm1 port• Pressure switchLength: 90mmWidth: 90mm1 port4mm socket incAdjusting lever operated

- -

• Piston accumulatorLength: 110mmWidth: 60mm2 port• Piston accumulatorLength: 110mmWidth: 60mm2 port

- -

• Diaphragm accumulatorLength: 80mmWidth: 60mm2 port

- -

• Bladder accumulatorLength: 120mmWidth: 60mm2 port

- -

• 3/2 way solenoid valveLength: 100mmWidth: 60mm3 port4mm socket inc.Power DC 24V

- -

• 4/2 way single solenoid valveLength: 100mmWidth: 60mm4 port4mm socket incPower DC 24C

- -

• 4/2 way double solenoid valveLength: 100mmWidth: 60mm4 port4mm socket incPower DC 24C

- -

• 4/3 way solenoid valve(PT connected)Length: 100mmWidth: 60mm4 port4mm socket incPower DC 24C

- -

• 4/3 solenoid valve(ABT connected)Length: 100mmWidth: 60mm4 port4mm socket incPower DC 24C• 4/3 way solenoid valve(all block type)Length: 100mmWidth: 60mm4 port4mm socket incPower DC 24C• T connector Length: 75mmWidth: 60mm3 port

Page 19





• + connectorLength: 75mmWidth: 60mm4 port• Transparent model hoseLength: 1mInner diameter: 4mmMax pressure 20kg f/cm3• Hydraulic transparent model workbookCOMPLETE AND COMPATABLE IN ALL RESPECTS, , OR EQUIVALENT OF BEST QUALITY.

11

Maintenance and Repair Tool kit (1 each)Ball Peen hammer 2lbsFlat screw driver set 6”,8”,10”,12Philip screw driver setSteel measuring tape 3mmChisel flat 6”8”10”Steel measuring tape 3mChisel flat 6”8”10”Ellen key set 1.5mm-10mm(set of 9PCS)Steel rule 150mm-300mmVernier caliper 0-300mm(digital)Outside micrometer 0-25mmCentre punch Set of 4 PCSDrift punch SetFlat file second cut 8”10”Round File diameter (6mm,10mm,12mm)Try square 150mmGreece gun metal body Bearing puller 200m,250mm(3legs)Hand hacksaw 12”( Adjustable frame)Combination pliers 150mm,200mmPipe wrench 10”,12”Adjustable wrench 8”,10”,12”Open ended spanner 4mm-24mmElectric hand drill machine( 12mm)Twist drill set

Thailand/Indonesia/UK/Equivalent 1 - - - -

- - - - -

1

Barometer (2 each)I. Direct Mercury BarometerII. FORTIN BarometerIII. ANEROID Barometer

COMPLETE AND COMPATABLE IN ALL RESPECTS, , OR EQUIVALENT OF BEST QUALITY.

UK/Japan/Germany/Thiland or Equivalent 2 -

Total Hydraullic & Material Testing LabMech-322 APPLIED

Page 20





2

Dead Weight Gauge Tester with Pressure gaugeSpecifications

SPECIFICATION

CYLINDER - BRASS. PISTON - High quality stainless steel , cross – sectional area 333 mm2

Pressure gauge-bourdon tube type with scale graduated 0-200 KN /m2 in 10 KN /m2 Intervals (also available in imperial units ). Weights 4 each 1, 0 kg 2 each 0,5 kg 1 each 0,2 kg Materials and finishes have been chosen carefully to give the fullest Protection against corrosion .

COMPLETE AND COMPATABLE IN ALL RESPECTS, , OR EQUIVALENT OF BEST QUALITY


Steam Turbine Power SystemExperimental opportunities:Energy relationships and the First Law ofThermodynamics.Cycle analysis and the Second Law ofThermodynamics.Control volume analysis.Entropy analysis.Isentropic analysis and the study of turbine/nozzle efficiency.Heat transfer analysis and the study of boilerefficiency.Combustion processes.Vapor power system fundamentals.Electric power generation.Experimental and data acquisition technique.

UK/Japan/Germany/Thiland/Indonisa or Equivalent 1 - - - -

Page 21




%Items with complete specificationsA steam electric power plant designed for engineering education. Consisting of a fossil-fueled boiler, steam turbine and condenser tower mounted on a rigid, mobile frame. Boiler of a tube-type, flame through design with access doors to view the inner workings. Steam rate adjustable through a steam admission valve, regulating turbine speed and power output. Axial flow turbine used to drive an alternating current generator. Generator output to be rectified allowing the output of direct current. Generator output capable of delivering 15Volts at 1 Amp to infinitely adjustable 15 Watt load. Unit to include analog boiler pressure gauge, generator voltage and generator current meters. To be supplied with a USB based digital data acquisition system complete with computer and user configurable data acquisition software capable of measuring and recording analog, digital and frequency signals. Equipped with calibrated transducers and thermocouples capable of measuring boiler temperature and pressure, turbine inlet and exit temperature and pressure, turbine RPM, fuel flow rate and generator load, voltage and current. All metal surfaces to be stainless steel, anodized or powder coated to promote durability and wear resistance. Provided with a comprehensive Operator’s Manual with design, operation and construction information. Provided with summary operating check lists for all operating conditions. Provided with safety instructions to address all operating conditions.

-

4 Thermocouples(Different Ranges and types) 0-1500 oC


5 Sectioned model of Simple Vertical Boiler -do- 1 - - - -

6 Sectioned model of COCHRAN (Multi tubular boiler)

-do- 1 - -

7 Sectioned model of Marine Boiler (Scotch types).

-do- 1 - -

8 Sectioned model of Locomotive Boiler -do- 1 - -

9 Sectioned model of Babcock and Wilcox Boiler

-do- 1 - -

10

Cut away model of safety and control valvesSpecifications Complete set containing safety valves, Globe valve, Gate valve, Ball valve and Swing check valve showing their inner working and along with their manual.

-do- 1 - -

11

Training Steam Boiler (100Kg/h)

SpecificationBoiler unit:- Type : Vertical, water tube.- Capacity : Up to 100 kg/hr steam.: Up to 10 kg/cm2 pressure.- Boiler instrument and safety devices include:: Pressure gauge and switch.: Temperature gauge.: Safety valve.: Level gauge and switch.: Safety alarm.- Boiler accessories include:: Steam separator.: Stack.

-do- 1 - - - -

Burner:European Made Force Draft with Built in Atomizer & PumpType : On – Off, automaticFuel : Diesel oil, Kerosene or any other Light Oil Optional: Gas Fired (LPG/NG).

-

3

Page 22





Feed water system includes:Resin filter for public water.Water Softner Filtration with activated Carbon Pressure gauge.Soft water tank.Feed water pump.Water meter for steam rate monitoring.Temperature gauge.

-

Fuel system includes:- Fuel tank- Fuel flow meter

COMPLETE AND COMPATABLE IN ALL RESPECTS (ALONGWITH INSTALLATION) , OR EQUIVALENT OF BEST QUALITY.

-

12

Working model of steam Turbine (Impulse and Reaction type)

Specifications

Dimensions Approx:Rankine cycler : 58 *78 * 30 inches ( 148 * 122* 77 cm ) Weight Approx:Rankine cycler : 400lbs (182 kg )

UK/Japan/Germany/Taiwan/Indonisa or Equivalent 1 - - - -

Instrumentation

Digital : high speed data acquisition system Data acquisition software with configurable data output windows laptop computer for on – screen data display single cable PC connection Multiple analog INMultiple digital IN/OUT 4 Frequency / Pulse IN

Sensors ( Preinstalled and calibrated )

Boiler temperature and pressure Turbine inlet temperature and pressure Turbine exit temperature and pressure Turbine RPM Fuel flow System electrical load Generator voltage output & current draw Analog : boiler pressure , generator voltage output & current draw2

-

Page 23





Operating conditions / limitations

Boiler : pressure 120 psi ( 827 kpa ) temperature 482 degree F (250 degree C)

Generator : 15.0 volts , 1.0 Amp ( total load of 15.0 watts )

Operating requirements

Typical laboratory or classroom setting Power : 220V Single Phase Fuel : liquid petroleum


-

13

Gas Turbine Power SystemExperimental opportunities Experimental and research opportunities include scientific, engineering, thermodynamic and environmental investigations. With a wide array ofsensors, experiments relating to secondary education physics and chemistry through graduate level fuels and combustion research are readilyperformed. Standard courses in engineering thermodynamics and fluid mechanics benefit from textbook direct examples conducted andmeasured in real time. The limitations of theoretical models and the variability of experimental technique can be experienced first hand. Inaddition to academics, the MiniLab™ is ideally suited for general gas turbine familiarization and jet engine operational training for aviation andmilitary professionals. Illustrative examples of Gas Turbine computations ~

-do- 1 - - - -

With measured values of compressor inlet temperature and pressure, turbine inlet temperature and pressure, turbine exit temperature and pressure, fuel flow and inlet and exit areas, possible calculations include:• Compressor Analysis - compressor pressure ratio, power required, rotational speed and compressor efficiency• Turbine Analysis - work and power developed, expansion ratio and turbine efficiency• Cycle / Brayton Type Analysis - mass flow rate, inlet and exit velocity, station temperature and pressures, combustion and thermal efficiency, specific fuel consumption and power / thrust developed• Combustion Analysis - excess air and fuel-air ratio• General Analysis - diffuser and nozzle performance and efficiency

-

Page 24




%Items with complete specificationsA complete gas-turbine power system to consist of an engine designed and manufactured for engineering education.Engine must utilize a centrifugal flow compressor, reverse flow annular combustor and an axial flow turbine stage.Engine to be of current manufacture and consisting of all new components.All engine components either vacuum investment cast or precision CNC machined.All high-heat components manufactured from 17-4 ph stainless steel, Inconel® 718or CMR 247 Super Alloy.Traceable and verifiable material to be used throughout engine.All elements comprising the system to be contained in a rigid steel chassis mounted on rolling castors. All system metal surfaces to be stainless steel, anodized or powder coated to promote durability and wear resistance.Complete system not to require any permanent facility modifications or additions. Engine situated behind transparent protective shields allowing clear view

-

Operator panel to consist of digital TIT, EGT, and RPM indicators, analog oil pressure, engine pressure ratio, fuel pressure and air pressure gauges, keyed master, green start red stop and T-handled power control lever.System to be equipped with calibrated transducers and thermocouples capable of measuring compressor inlet, compressor exit, turbine stage inlet, turbine stage exit and thrust nozzle exit temperature and pressures, fuel flow, thrust and engine compressor /turbine rotational speed.Engine thrust to be measured by a load cell permitting direct indication of thrust value.To be supplied with a USB based digital data acquisition system complete with computer and user configurable data acquisition software capable of measuring and recording analog, digital and frequency signals.Fully automatic engine start and operational health monitoring system provided with LCD status readout and cumulative run-time and cycle count. Representative engine components and technical data optionally available for teaching use and training aids.

-

Page 25





14

Reciprocating air compressor Study BenchSpecifications and features • Measurement of intake and delivery pressure• Airflow rate• compressor speed• Temperatures• Determination of the volumetric and isothermal efficiency• Compressor, 1 cylinder, single-stage• Power consumption: 750W• nominal speed: 980rpm• operating pressure: 8bar• max. pressure: 10bar• intake capacity: 150L/min at 8bar• Safety valve blow off pressure: 10bar• Pressure vessel 16bar• capacity: 100L


Measuring ranges - temperature: 2x 0...200°C- pressure: -1...1bar / 0...16bar- differential pressure: 0...10mbar- 2 manometers: -1...4bar / 0...16bar


-

15

Rotary air compressorFeatures

Screw air compressor with air receiver or portable screw air compressor with air tank (2KW~5KW)SpecificationsPressure : 5Bar ~ 10 BarTank: 200 LitersWith Education training manuals & all standard Accessories

-do- 1 - - - -

16

Ignition point Testing equipmentBattery Ignition system for Single spark plug and multi spark plug= 02Magneto Ignition system for Single spark plug and multi spark plug= 02

-do- 1 - -

Page 26





19

AC System Trainer (Heating and Cooling)SpecificationsCompressor unit with condenser 3-Phase AC motor, 3 HP, 380V, 50HzAutomatic regulating valve for cooling water calibrating tank to measure the water condensed at dew point conditions venturi meter to control the return air flow double damperCentral fan with variable speed motor variable heating coil, 2kW+1kW humidification station2 stage direct cooling coilReheating, 1kWRegulating system for conditioned air 6 hygrometers for relative humidity control6 dial thermometers for air controlPressure switches, solenoid valves, expansion valves, hand valve for Freon circuit


-do- 1 - - - -

21

Working models of Petrol EngineA= 2 Stroke Petrol EngineB= 4 Stroke Petrol EngineSpecifications Single Cylinder 2 stroke and 4 strokes with important parts including valve control, Ignition system and Carburetor, sectioned model made of original parts.


-do- 1 - - - -

22

Working models of Diesel EngineA= 2 Stroke Diesel EngineB= 4 Stroke Diesel EngineSpecifications Single Cylinder 2 stroke and 4 strokes with Indirect injection, valve and piston movement, mode of injection pump and nozzle can be demonstrated sectioned model made of original parts.


-do- 1 - - - -

Page 27





23

Maintenance and Repair Tool kitBall Peen hammer 2lbsFlat screw driver set 6”,8”,10”,12Philip screw driver setSteel measuring tape 3mChisel flat 6”8”10”Chisel flat 6”8”10”Ellen key set 1.5mm-10mm(set of 9PCS)Steel rule 150mm-300mmVernier caliper 0-300mm(digital)Outside micrometer 0-25mmCentre punch Set of 4 PCSDrift punch SetFlat file second cut 8”10”Round File diameter (6mm,10mm,12mm)Try square 150mmGreece gun metal body Bearing puller 200m,250mm(3legs)Hand hacksaw 12”( Adjustable frame)Pipe wrench 10”,12”Adjustable wrench 8”,10”,12”Open ended spanner 4mm-24mmElectric hand drill machine( 12mm)

-do- 1 -

Twist drill set5mm,8mm,10mm,12mm(02,each)Tap set with handle 5mm,6mm,8mm,10mm( 01,each)Fix die set with handle 6mm,8mm,10mm,12mmTap extractor 6-12mmOil can ½ literEasy out 5-12 MMWith tool box made of M.S. sheet (Best quality)

-

- - - - -

1

UNIVERSAL HARDNESS TESTING MACHINE FOR BRINELL, ROCKWELL AND VICKERS HARDNESS TESTSpecificationMeasuring range: 5-400HBS, 25-85HRA, 25-100HRB, 20-70HRC, 210-1000HVTest load: 294.2, 306.5, 588.4, 612.9, 980.7, 1471, 1839N (30, 31.25, 60, 62.5, 100, 150, 187.5kgf)Max. height of tester piece: 150-210mmPower supply: 220V or 110V AC, 50/60HzMain AccessoriesLarge flat anvil: 1 pcSmall flat anvil: 1 pcV-notch anvil: 1 pcDiamond cone penetrator: 1 pcDiamond pyramid penetrator: 1 pcsSteel ball penetrator: Ø 1.588, Ø 2.5, Ø 5mm 1 pc eachBrinell standardized block: 1 pcRockwell standardized block: 5 pcs.Vickers standardized block: 1 pc40X readout microscope: 1 pc

COMPLETE AND COMPATABLE IN

UK/Japan/Germany/Taiwan/Korca or Equivalent 1 - - - -

Total Applied ThermoddynamicsMATERIALS TESTING AND HEAT TREATMENT

Page 28





4

Universal Testing Machine(Computerized, 50-100KN capacity)Specification• Max Test load =100KN• Load range =0-20KN ,0-50 KN ,0-100 KN• Accessories;• Grip for round specimen 0-20mm• Grip for flat specimen 0-15mm• Instructional manual• Fixture for Bend, Shear, compression and tensile test• Extensometer• Tool kit • Graphical unit accessories


-do- 1 - - - -

5

Readout Microscope:Suitable to measure the diameter of indentation in Brinell Hardness testing, determine the width and length of scale mark, slit, key slot and dent. Check metal surface quality, density of fiber and field specimens, etc.Specification:Magnification: 40XEffective field view range (mm): Ø3Dimensions (mm): 70 x 50 x 187


UK/Japan/Germany/Korca/Thiland or Equivalent 1 -

6

Torsion Testing machine Along with all standard and optional accessoriesSpecificationMeasuring range = 5-500 N-mMeasuring range of scale = 0-50 N-M 0-100 N-m 0-200 N-m 0-500 N-mDistance of between grips = 0-600 mmDiameter of specimen =5-18mm


-do- 1 - - - -

Page 29





9

Specimen Cutoff MachineWith all Standard accessories and attachmentsSpecification• Bench mounted cut off machine• Safety switch to hood• Two quick claiming vices with mountings for horizontal and vertical• Coolant using two adjustable jets either side of wheel• Cutting wheel diameter : 250mm - 300mm• Two rotation speeds of cut wheel : 3200rpm - 3800 rpm• 230V single phaseCOMPLETE AND COMPATABLE IN ALL RESPECTS, , OR EQUIVALENT OF BEST QUALITY.

-do- 1 -

10

Magnetic particle testing equipment

Machine Specifications• Coil 16" Diameter, 7500 ampere turn• Power Supply Output 3000 amp AC• Electrical requirements 230 V 1ph 50AAccessories:• Central Conductors• UV Glasses• Work Rest Extension KitCOMPLETE AND COMPATABLE IN ALL RESPECTS, , OR EQUIVALENT OF BEST QUALITY.

-do- 1 -

11

Heat treatment FurnaceWith Complete electric control panel and fittingsTemperature range up to 1500’C


-do- 1 - - - -

12

Specimen Polishing MachineWith all types necessary polishing clothsSpecification• Double interchangeable 200/250mm diameter plates• Single motor with drive belt variable speed 20 to 600 rpm• 230V single phase• 2 Pre select speeds 150 and 300 rpm• 2 rotation direction• Digital display of speed• Touch sensitive controls• Water flow controlled by electromagnetic valve• Multi-jet water spray systemCOMPLETE AND COMPATABLE IN ALL RESPECTS, , OR EQUIVALENT OF BEST QUALITY

UK/Japan/Germany/Taiwan/Indonisa or Equivalent 1 -

Page 30





15

Metallurgical Microscope: • 100X to 1000X TRINOCULAR INVERTED• METALLURGICAL – METALLOGRAPHIC MICROSCOPE • MEASURING KIT• USB DIGITAL JPG IMAGE CAMERACOMPLETE AND COMPATABLE IN ALL RESPECTS, , OR EQUIVALENT OF BEST QUALITY

-do- 1 -

16

ThermocoupleType k temp range 0-1200cDia. 21.7mm,with digital temp controllerCOMPLETE AND COMPATABLE IN ALL RESPECTS, , OR EQUIVALENT OF BEST QUALITY

-do- 1 -

17

Maintenance and Repair Tool kitBall Peen hammer 2lbsFlat screw driver set 6”,8”,10”,12Philip screw driver setChisel flat 6”8”10”Steel measuring tape 3mChisel flat 6”8”10”Ellen key set 1.5mm-10mm(set of 9PCS)Steel rule 150mm-300mmVernier caliper 0-300mm(digital)Outside micrometer 0-25mmCentre punch Set of 4 PCSDrift punch SetFlat file second cut 8”10”Round File diameter (6mm,10mm,12mm)Try square 150mmGreece gun metal body Bearing puller 200m,250mm(3legs)Hand hacksaw 12”( Adjustable frame)Pipe wrench 10”,12”Adjustable wrench 8”,10”,12”

-do- 1 - - - -

Open ended spanner 4mm-24mmElectric hand drill machine( 12mm)Twist drill set5mm,8mm,10mm,12mm(02,each)Tap set with handle 5mm,6mm,8mm,10mm( 01,each)Fix die set with handle 6mm,8mm,10mm,12mmTap extractor 6-12mmOil can ½ literEasy out 5-12 mmWith tool box made of M.S. sheet (Best quality)Open ended spanner 4mm-24mmElectric hand drill machine( 12mm)Twist drill set5mm,8mm,10mm,12mm(02,each)Tap set with handle 5mm,6mm,8mm,10mm( 01,each)Fix die set with handle 6mm,8mm,10mm,12mmTap extractor 6-12mmOil can ½ literEasy out 5-12 mmWith tool box made of M.S. sheet (Best quality)

-

- - - - Total Material Testing and Heat Treatement

Page 31





-

4

Pedestal tool grinderWheel size = 250x25x25Motor 440v, 0Hz, 3Ph = 01 HPGrinding wheels Al2O3 Number 46 and 60 fitted with machine ,Safety guard, Eye Shield, Tool rest, Grease gun, Wheel dresser . Complete in all respect.


Pak/UK/China or Equivalent 2 - - - -

7

Surface grinding machine SpecificationFor grinding accurate jobs, accuracy 0.001mm, digital read out, workstation light, coolant supply attachment, work table hydraulic control.Table clamping surface (mm) = 550x300 to 600x300.Table longitudinal travel (mm) = 550 to 600Table cross travel (mm) = 300 to 350.Cross feed infinitely variable (m/stroke) = 0-20Grinding wheel size (mm) = 250x32x76.Motor power 3Ph = 3kw.With all standard accessories, tool kit, tool cabinet, operation manual etc .complete in all respect with DRO.


Pak/UK/Japan/Germany or Equivalent 1 - - - -

8

Universal tool & cutter grinding machine SpecificationSuitable to grind all types of tool and cutters.Clamping area of table (mm) =820x 140.Longitudinal table travel (mm) =450.Lateral table travel (mm) = 225.Distance between centers (mm) = 600-650Height of center (mm) =125-130Spindle speed (rpm) =2800- 5600.Motor power 3ph = 1 kw.Table angle setting (degrees) =±450.Grinding head tilting on vertical axis (degrees) = ±3600.Grinding head tilting on horizontal axis (degrees) = ±150.


Mech-374 WORKSHOP PRACTICE - III

Page 32





Attachments Face milling cutter grinding attachment (mm) = 450.Radius grinding attachment (mm) = 0-25.Cylindrical grinding attachment (mm) = 250.Internal grinding attachment (mm) =12-50.Indexing attachment = 01Extended grinding wheel spindle (mm) = 75.Universal vice (mm) = 100x25x75.Drill point grinding attachment (mm) = 3-25.Lathe and planer tool grinding attachment (mm) =10-38.Set of spring collets (mm) = 6, 8, 10, 12 ,16, 20.

-

Accessories Work head = 1.Left hand tail stock = 1.Right hand tail stock = 1.Diamond wheel dresser = 1.Setoff wheel guards = 1.Universal tooth rest = 1.Center height gauge = 1.Collect wrench = 1.Ejector rod = 1T- wrench = 1.Pin wrench = 1.Grinding wheel sleeves = 5.Set of grinding wheels different shapes = 7.Spindle extension 100 mm =1.Belt for spindle drive = 1.Suitable tool cabinet = 1.Instruction / operation manual, complete in all respect.


-

9

Vertical differential type Hobbing machine SpecificationVertical differential type machine capable to cut spur gears, helical gears and worm gears, heaving even, odd, prime number of teeth. Built in coolant and lubrication pump.Maximum module for gears (mm) = 6.Maximum diameter of gear hob wit out outer support (mm) = 400-500.Maximum diameter of helical gears hobbed (mm) = 370.Hob diameter (mm) = 120.Hob arbor diameter (mm) = 22, 27, 32.Work mandrel diameter (mm) = 30.Spindle speeds (8) rpm = 50-300Hob down feed per rev. of job (mm) = 0.24-4Main drive motor 3Ph 1420 rpm = 3kw.With all standard accessories, tool kit, tool cabinet, operation manual, Maintenance manual etc.


UK/Japan/Germany/Thiland/Korca or Equivalent 1 - - - -

Page 33





14

SWIVEL BASE VICE Hardened and ground jaws with vice handle.Width of jaws (mm) = 210.Height of jaws (mm) = 63.Jaws opening minimum (mm) =160.Index swivel base = ± 360 degree.Combatable with universal milling machine.

Pak/UK/Japan or Equivalent 4 - - - -

17

STRAIGHT SHANK END MILL (Best Quality) Made of cobalt alloy HSS, hardened and ground cutting teeth.Shank diameter (mm) = 16.Combatable with universal milling machine

Pak/UK/Japan/Germany or Equivalent 4 - - -

18

RADIUS NOSE END MILL(Best Quality) Made of cobalt alloy HSS, hardened and ground cutting teeth.Nose radius (mm) = 6Cutter diameter (mm) = 12.Combatable with universal milling machine

-do- 4 - - -

19

RADIUS NOSE END MILL(Best Quality) Made of cobalt alloy HSS, hardened and ground cutting teeth.Nose radius (mm) = 12

-do- 5 - - - -

20

CORNER ROUNDING END MILL(Best Quality) Made of cobalt alloy HSS, hardened and ground cutting teeth.Nose radius (mm) = 6,.Shank diameter (mm) =20.Combatable with universal milling machine

-do- 5 - - -

21

WOOD RUFF KEY SEAT CUTTER(Best Quality) Made of cobalt alloy HSS, hardened and ground cutting teeth.Key dimension (mm) = 6x32.Cutter diameter (mm) = 32.5.Cutter width (mm) = 6.Shank diameter (mm) = 18.Combatable with universal milling machine

-do- 2 - - - -

22

T-SLOT CUTTER(Best Quality) Made of cobalt alloy HSS, hardened and ground cutting teeth, right handed with under cut staggered teeth.Cutter diameter (mm) = 31.2.Cutter width (mm) = 12.6.Over all length (mm) = 100.Shank diameter (mm) =18.Combatable with universal milling machine

-do- 5 - - - -

23

DOVE TAIL CUTTER(Best Quality) Made of cobalt alloy HSS, hardened and ground cutting teeth.Cutter diameter (mm) = 32, Cutter angle (degrees) = 60 Cutting length (mm) =12.5, Shank diameter (mm) = 16, Combatable with universal milling machine

-do- 2 - - - -

Page 34





24

SINGLE ANGLE MILLING CUTTER(Best Quality) Made of cobalt alloy HSS, hardened and ground cutting teeth.Angle of cutting (degrees) = 45Diameter (mm) = 60Width (mm) = 12, Bore diameter (mm) = 22,.Combatable with universal milling machine

UK/Japan/Germany/Korca/Thiland or Equivalent 2 - - - -

25

SHELL END MILLS(Best Quality) Made of cobalt alloy HSS, hardened and ground cutting teeth.Diameter x width (mm) = 50 x36,.Bore diameter (mm) = 22

-do- 2 - - - -

26

CONCAVE MILLING CUTTER(Best Quality) Made of cobalt alloy HSS, hardened and ground cutting teeth.Radius (mm) = 2.5,.Diameter (mm) = 63, Width (mm) = 10, Bore diameter (mm) = 22,.Combatable with universal milling machine

-do- 2 - - - -

27

CONVEX MILLING CUTTER(Best Quality) Made of cobalt alloy HSS, hardened and ground cutting teeth.Radius (mm) = 5, Diameter (mm) = 63, Width (mm) = 10, Bore diameter (mm) = 22, Combatable with universal milling machine

-do- 2 - - - -

28

SIDE AND FACE MILLING CUTTER(Best Quality) Made of cobalt alloy HSS, hardened and ground staggered cutting teeth.Cutter diameter (mm) = 63, Width of cutter (mm) = 8, Bore diameter (mm) = 22Combatable with universal milling machine

-do- 5 - - - -

29

INVOLUTE SPUR GEAR CUTTER(Best Quality) Made for cobalt alloy HSS or Sintered steel powder, extreme toughness, good grinding characteristics, set of 8 cutters, pressure angle 20 degrees.Module = 1.75.Cutter diameter (mm) = 55Bore diameter (mm) = 22, Combatable with universal milling machine

-do-4

Set - - - -

30

SLITTING SAW(Best Quality) Made of cobalt alloy HSS, hardened and ground cutting teeth.Width of cutter (mm) =, 3.Cutter diameter (mm) = 80.Bore diameter (mm) = 22.Combatable with universal milling machine

-do- 2 - - - -

Page 35





31

HOB CUTTERS(Best Quality) Made of high quality HSS, hardened and ground cutting teeth, high wearing resistance.Right hand hob single start 20 degree pressure angle bore size 22mm module 1.75,2.00 .Right hand hob single start 20 degree pressure angle bore size 27mm. module 2.5,3.00Combatable withhobbing machine

-do- 1 - - - -

33

DIAL CALIPER(Best Quality) Rack and pinion mechanism, depth bar sharp jaws edges, raised edges of beam.Measuring range (mm) =0-200.Resolution (mm) = 0.05.

-do- 5 - - - -

35

DIGITAL DEPTH GAUGE(Best Quality) Two measuring mode ABS and INC, LCD display.Base size (mm) 100.Measuring range (mm) = 0-200.Resolution (mm) = 0.01.

-do- 1 - - - -

37

COMBINATION SET(Best Quality) Three measuring heads attached to ground steel rule square head 45 degree and 90 degree, center head, protractor head 0-180, scribe, sprit level.Measuring range (mm) = 0-300.

-do- 2 - - -

38

STEEL RULE(Best Quality) Sharp and clear graduation marks made of anti rust steelRange (mm) = 300.Minimum reading (mm) = 0.5.

-do- 10 - - -

39

RADIUS GAUGE(Best Quality) Made of fine steel radius sizes stamped, convex and concave radius with locking device.Measuring radius (mm) = 0.5-13.Radius interval (mm) =0.5.Number of leaves = 26.

Pak/UK/Germany/Japan or Equivalent 5 - - -

40

DRILL SLEEVES(Best Quality) Ground externally and reamed internally, hard tang, Morse taper.External/Internal taper = 2/1, 3/1.

-do- 2 - - - -

41

HAMMER (BALL PEIN) (Best Quality) Made of cast steel hardened and ground peen and face. Suitable wooden handle.Weight of hammer (Kg) = 0.250.Weight of hammer (Kg) = 0.500.

-do- 5 - - - -

42

HAMMER (CROSS PEIN) (Best Quality) Made of cast steel hardened and ground peen and face. Suitable wooden handle.Weight of hammer (Kg) = 0.250.Weight of hammer (Kg) = 0.500.

-do- 5 - - - -

43ADJUSTABLE WRENCH(Best Quality) Made of forged steel, chrome platedSize (mm) = 150, 300.

-do- 2 - - - -

Page 36





44

ELEN KEY SET(Best Quality) Made of chromium-vanadium steel.Measurement system = metric.No of keys = 12.Sizes (mm) = 1.5, 2, 2.5, 3, 4, 5, 5.5, 6, 8, 10, 11, 12.

-do- 2 - - - -

46

BEARING PULLER(Best Quality) Made of drop forged steel, 3 legs.Maximum spread (mm) = 130.Maximum reach (mm) = 110.

-do- 2 - - - -

47

SURFACE TABLE Made of closed grain cast iron properly polished and aged fitted with suitable legs.Length x width x Thickness (mm) = 630x630x80.

-do- 1 - - -

49

GREASE GUN(Best Quality) Metallic body and metallic handle along with leather piston, with pointed and flaring nozzle.Reservoir capacity (L x D) = 280 x 56. (mm)

-do- 2 - - - -

50

Maintenance and Repair Tool kitBall Peen hammer 2lbsFlat screw driver set 6”,8”,10”,12Philip screw driver setSteel measuring tape 3mmChisel flat 6”8”10”Steel measuring tape 3mChisel flat 6”8”10”Ellen key set 1.5mm-10mm(set of 9PCS)Steel rule 150mm-300mmVernier caliper 0-300mm(digital)Outside micrometer 0-25mmCentre punch Set of 4 PCSDrift punch SetFlat file second cut 8”10”Round File diameter (6mm,10mm,12mm)

-do- 1 - - - -

Try square 150mmGreece gun metal body Bearing puller 200m,250mm(3legs)Hand hacksaw 12”( Adjustable frame)Pipe wrench 10”,12”Adjustable wrench 8”,10”,12”Open ended spanner 4mm-24mmElectric hand drill machine( 12mm)Twist drill set5mm,8mm,10mm,12mm(02,each)Tap set with handle 5mm,6mm,8mm,10mm( 01,each)Fix die set with handle 6mm,8mm,10mm,12mmTap extractor 6-12mmOil can ½ literEasy outWith tool box made of M.S. sheet (Best quality)

- - -

- - - - - - -

1 3D CAD Software (Solid Modeling) 25 - - -

2 3D CAM Software (Milling, Turning, Turn/Mill, Wire Cut) 25 - - -

3 Simulation Software 50 - - - -

5 3D Solid Modeling Software (Kinetics, Static and Dynamic Analysis) 25 - - -

6 Machine Design Simulation Software 1 - - - - - - -

Total Workshop Practice IIIMech-382 CAD / CAM

Total CAD/CAM

Page 37





- - -

3

CNC Wire Cut MachineSpecification• Work table size(mm): 800x400 to 900x600• X Travel (mm) 450-500• Y Travel (mm) 600-650 • Max. work piece thickness(mm): 250 to 300• Wire traveling speed(m/s): 8-12• Wire diameter(mm): 0.15-0.2• Max. cutting speed(mm/min): 100-120• Power Consumption ( Kva)= 1.5 – 2.0• Controller Type = Fanuc or Equivalent• Maximum taper angle /plate thickness =±30/100COMPLETE AND COMPATABLE IN ALL RESPECTS, , OR EQUIVALENT OF BEST QUALITY

UK/Korca/Japan/Thiland/Germany or Equivalent 1 - - - -

7

Metal Cutting Band sawMotor =3Ø 2HPStep Saw Blade Speed / Variable Saw Blade Speed = 50Hz 95 164 239 314(FPM) 29 50 73 96(MPM) 60Hz 95-402(FPM) 29 122(MPM) / 50Hz 78-335(FPM) 24-102(MPM)Blade Size WxTxL = 27x0.9x3280mmDimension LxWxH 1720x620x1055mmCUTTING CAPACITY - -0° =Bar Ø250mm(10")45° =Bar Ø150mm(6")

COMPLETE AND COMPATABLE IN ALL RESPECTS, OR EQUIVALENT OF BEST QUALITY

-do- 1 - - - -

8

Maintenance and Repair Tool kitBall Peen hammer 2lbsFlat screw driver set 6”,8”,10”,12Philip screw driver setSteel measuring tape 3mmChisel flat 6”8”10”Steel measuring tape 3mChisel flat 6”8”10”Ellen key set 1.5mm-10mm(set of 9PCS)Steel rule 150mm-300mmVernier caliper 0-300mm(digital)Outside micrometer 0-25mmCentre punch Set of 4 PCSDrift punch SetFlat file second cut 8”10”Round File diameter (6mm,10mm,12mm)Try square 150mmGreece gun metal body Bearing puller 200m,250mm(3legs)Hand hacksaw 12”( Adjustable frame)

-do- 1 - - - -

Mech-392 CNC MACHINES

Page 38





Pipe wrench 10”,12”Adjustable wrench 8”,10”,12”Open ended spanner 4mm-24mmElectric hand drill machine( 12mm)Twist drill set5mm,8mm,10mm,12mm(02,each)Tap set with handle 5mm,6mm,8mm,10mm( 01,each)Fix die set with handle 6mm,8mm,10mm,12mmTap extractor 6-12mmOil can ½ literEasy out 5-12 mm.With tool box made of M.S. sheet (Best quality)

- - -

- - - -

- - - -

3 Mechatronics Work Cell with Machine Vision and Sensors

Robot vision cell: arranging polletes,

storoge area with bose frome safety housing,

cemera system. (Object detection, positioning,

Orientation & Communication) USA, Germany or Equivalent

5

5 Manufacturing System Flexible Manufacturing System

Distribotion station, Testing station, Robot

handling section, Tronsmission unti

(Conveyor), CNC process unit. Inspection unit.

Storge unit. Progrmming & Simvlation. Software

package. PLC controlled. USA, Germany or

Equivalent

1

1

Jaw Crusher, :with 3 phase 50 to 220 volt, V.Belt Drive with 3 to 3.5 jaw opening, 500 RPM speed capacity50-150 ib/hr.bench space 14.5x21 to reduce rock lamps from 2.5 dia to pass on 10 mesh or finer sieve jaws made of manganese steel corrugated faces

PAK/CHINA or Equivalent 2

2

Pulverizer:Bron/c casting steel rotor 220 volt, 3 phase, 50N, I HP Motor 2600 RPM with V.Belt drive at guards 1.00 ammeter Extra retaining screen with fabric bags for oulet mounted on legs 2 casters for easy movement.


Remarks Unit Rate Total Rate without GST

GST @ 17 %

Total Rate with GST Sr # Items with complete specifications Specification Qty

Remarks

COMPREHENSIVE MECHATRONICS LAB:

Total

CHEMICAL TECHNOLOGY

Unit Rate Total Rate without GST

GST @ 17 %

Total Rate with GST Sr # Items with complete specifications Specification Qty

Total CNC MachinesGrand Total Mechanical Technology:

MECHATRONICS TECHNOLOGY

Page 39





3Centrifugal pump: with 1/2 HP motor single phase capacity 250gal/min, 30 feet head for 220 volt, 50 N in casting.


4

Sample Grinder:Open door dice tyhpe with locking hand wheel to regulate product size antiracism bearings, cast iron traction with stud dises 0 with 6" dia dise capacity 200Ib/hr at 20mesh with 2 HP motor, 220 Volt 50 N mlounted on a common mounting base.


5

LabBall mill: for wet and dry grinding for ores etc. Sixe: 16" dia mill, 16"x16" with welded stud base extra thick shell with integral cast lifter bars. Capacity: 150Ib/hr complete wsith 250 Ib of stud balls with 1 1/2 HP 3 phase motor 550 volts 50N operation.


14Portable mixer, with direct drive 4 inch diameter, Stainless steel propellers. 1/4 HP single phgase 50 cyucles. 220 v motor


15

Mixing Tank: Capacity 10 gallons stainless steel dull polished inside, Desalted ouside slopping bottom of out let connection rein forced top brim steel legs. Complete with ss cover. Outlet valve casters and mixer frame


19

Water Diminerilizer :Equipped with different cell shoring % sodium chloride, water in put/ Out put flow rate 501/hr power 220-240v

UK/USA/Germany or Equivalent 4

20

Viscosity bath (0-40c): Sample holding capacity 4-6no thermostatic control stain less steel and glass frame for oil bath auto - stirring and their or stting. Operating voltage 220v


26Hand die threading set:Universal quick opening die head, with drop head threader size: 1/8 inch 1.25 inch


29Rectifier:To convert AC to DC Ac in put 220v Dc voltage up to 12v ampere up to 500


31Nephlo meter (digital portable):Both for coarse and homogeneous solutions. Power supply 220v Wave length 42-87 nm


32Magnetic stirrers with hot plates:Electric speet regulation of 150-2000 rpm Slectable reversible stirring motion


34Diesel index determination Apparatus:According to A D IN / ASTM STANDARD


43 First aid kit:With all accessories and medicines PAK or Equivalent 4

45 Calmel electrodes:Can fitted with PH Meter and tetrameter


46 Paltinum ElectrodesFor conductivity bridge


3 Platinum wire(sealed in glass rod,used for flame test 1-1.5 cm in length)


7 Tintometer UK/USA/Germany or Equivalent 2

11 Moisture tester UK/USA/Germany or Equivalent 2

Grand Total

GENERAL CHEMISTRY LAB

Page 40





3 Water softener (mixed bed type) UK/USA/Germany or Equivalent 2

4 Electronic aqua analyzer UK/USA/Germany or Equivalent 2

5 Cation type UK/USA/Germany or Equivalent 1

6 Anion type UK/USA/Germany or Equivalent 1

7 Vitamin tester (digital) UK/USA/Germany or Equivalent 2

8 Double jacketed soap pan PAK/ China or Equvalent 2

9 Bladder PAK/ China or Equvalent 1

10 Cake cutter PAK/ China or Equvalent 1

1 Burner PAK/ China or Equvalent 5

12 West paul balance UK/USA/Germany or Equivalent 5

13 Density motor UK/USA/Germany or Equivalent 2

15 Saybolt viscometer UK/USA/Germany or Equivalent 2

16 Ostwald's viscometer UK/USA/Germany or Equivalent 50

17 Staglometer UK/USA/Germany or Equivalent 50

9 Dobosque Colorimeter UK/USA/Germany or Equivalent 3

21 Technical Orsat Apratus for the analysis of flue gas


24 Electronic Balance digital display capacity 30kg aquricy 10-15gm


25 Electrician Tool Kit UK/USA/Germany or Equivalent 1

27 Aluminium Ladder (08ft) UK/USA/Germany or Equivalent 1

29 AC (Air conditioning unit) Capacity 02 ton, energy efficient

Germany/Japan/Korea or Equivalent 2

1

Hydraulic bench Equipped with all accessories for Oriface discharge, energy losses in pipe & fiting, Venturi Discharge, orifice meter, pitot tube


2 Multiple pump test Rig with Accessories UK/USA/Germany or Equivalent 1

ANALYTICAL LAB

Total:-

UNIT OPERATION LAB

INDUSTRIAL CHEMICAL PROCESS LAB

Total:

ORGANIC PHYSICAL LAB

Total:

Total:

Page 41





11 Centrifuge machine power driven speed 3000 rpm, 06 tubes with cover


4 Pipe cutter (circular blade) size 3" dia UK/USA/Germany or Equivalent 6

6 Pipe wrench (Sizes 6", 12",18") 3 pcs set UK/USA/Germany or Equivalent 5

7 Screw wrench (Sizes 6", 10", 12",15") 4 pcs set


9 Plier (Size 8" combination, 8" cuter, 6" long nose) 3 pcs set


11 Socket set (Size 5-10mm) UK/USA/Germany or Equivalent 6

14 Screw driver 7 pcs set chrome vanadium with steel headed top.


17 Straight peen Hammer (500gm, 250gm) wooden handle PAK/China or Equivalent 3

19 Flaring tool set UK/USA/Germany or Equivalent 3

24 Gate Valve Size 2" PAK/China or Equivalent 425 Globe Valve Size 2" PAK/China or Equivalent 426 Check Valve Size 2" PAK/China or Equivalent 427 Safety Valve Size 2" PAK/China or Equivalent 428 Butterfly Valve Size 2" PAK/China or Equivalent 429 Plug cook Valve Size 3/4" PAK/China or Equivalent 430 Expansion steam trap Size 1/2" PAK/China or Equivalent 431 Bucket steam trap Size 1/2" PAK/China or Equivalent 432 Impulse steam trap Size 1/2" PAK/China or Equivalent 4

39 Work bench Size length 4ft, width 2.5ft, height 3ft PAK/China or Equivalent 2

13 Wattmeter 3 Phase (5 / 25, 3 ф, 120/440) Germany/Taiwan or Equivalent 10

6 Fletcher’s trolley with all accessories (Standard) Pak/ China or Equivalent 12

16Searl's apparatus/young's modulus apparatus(Standard with range of 3 kg)

Pak/ China or Equivalent 12

18 Measuring tap Pak/ China or Equivalent 12

12 Spring balance - 100. 250, 500 gm Pak/ China or Equivalent 4


3 Magnifying Glass - 3” Pak/ China or Equivalent 40

Total Basic Electronic Lab:

RELATED STUDIES

PHYSICS LAB

Sr. No. Description of Equipment Specification Qty Unit Rate Total Rate

without GST GST @ 17

%

BASIC ELECTRONICS LAB

Sr # ITEMS Specification Qty Unit Rate Total Rate without GST

GST @ 17 %


COMPREHENSIVE WORKSHOP/LAB

Total:Grand Total:

TELECOMMUNICATION TECHNOLOGY

Total:

Page 42





19Steel wires 0.45mm dia swg 26 steel0.36mm dia swg 29 steel0.45mm dia swg 26 brass


25Tuning forks (25 set of 16 forks) - (consisting forks of frequency approx. (440 hz, 512 hz,480 hz)


28

Thermometer (different scales) China made - ½ degree upto 110º c½ degree upto nearly240º f


30 Screen Metal 300rnm x 300mm painted white Pak/ China or Equivalent 25

31 Electrical lamp -Table lamp type adjustable height and direction (Standard) Pak/ China or Equivalent 25

32 Point source adjustment - Wooden box type (Standard) Pak/ China or Equivalent 25

47 Spirit Level - Horizontal bubble (Standard) Pak/ China or Equivalent 50

49Sextant with all accessories - Educational model (Brass frame mm, Scale reading 0 to 130 degree centigrade in 10 division)


58 Wet and dry bulb hygrometer (Standard) Pak/ China or Equivalent 1259 Beakers - 250ml (Standard) Pak/ China or Equivalent 5064 Resined Flannel (Standard) Pak/ China or Equivalent 2

-

4 Funnel a) light glass - 3 inches or 75mm Pak Made/ China or Equivalent 25

9 Thermometer of different scale - (110 C) Germany/ Japan or Equivalent 44

13 Cork with hook Pak/ China or Equivalent 2515 Glass Pipe Pak/ China or Equivalent 10

17 Pipette 10ml Germany/ Japan or Equivalent 25

19 Analyticl / Electronic Balance - 0.1 gm to 500 gm 6

20 Crucible with lid 10

22 Pipette sucker (Digital) Germany/ Japan or Equivalent 25 -

23 Stalagmometer Germany/ Japan or Equivalent 50

24 Pinch Cock Pak/ China or Equivalent 5026 Hoffman's Voltameter UK/ Japan or Equivalent 10

28 Battery (12 V) D.C /Adapter - 300 milliampere UK/ Japan or Equivalent 10

31 Ammeter - 0-3 ampere Pak/ China or Equivalent 5

30 Copper Foils (5cm x 3cm) - 5cm x 3cm Pak/ China or Equivalent 5

5

UK/ Japan or Equivalent

21 Stop Watch - Digital Pak/ China or Equivalent

18 Specific gravity bottles - 25 ml Germany/ Japan or Equivalent 10

16 Ostwald Viscometer UK/ Japan or Equivalent 10

12 Two, Litres Measuring Cylinder or a bell jar or a long form beaker Chromatograph Tank

France/ Germany or Equivalent 30

11 Universal pH Paper Range - '1-14 Germany/ Japan or Equivalent 10

7 Spirit lamp - With stop cork Pak/ China or Equivalent 49

6 Filter paper - 10 x 12 inches Germany / UK or Equivalent 80

Beaker - 500 ml France/ Germany or Equivalent 5

2Beaker - 250ml France/ Germany or

Equivalent 30

LIST OF APPARATUS1 Beaker 100 ml France/ Germany or

Equivalent 30

Total:CHEMISTRY LAB

45 Sodium lamp (18 watt) (Standard) Pak/ China or Equivalent 5

Page 43





36 Platinum wire Pak/ China or Equivalent 25

40 Measuring Flask - 1000 ml France/ UK or Equivalent 10

Graduated Cylinder (100 ml) France/ Germany or Equivalent 25

Graduated Cylinder (50 ml) France/ Germany or Equivalent 25

49 Fusion Tube Pak/ China or Equivalent 250

55 Water Bath - Ordinary Size Japan/ UK or Equivalent 20

57 Tongs Pak/ China or Equivalent 25

13 Zinc Sulphate Germany/ UK or Equivalent

500 gm

16 Sand paper - 10 No. Pak/ China or Equivalent 10 No.

28 Phosphoric acid Germany/ UK or Equivalent

One Litre

30 Sodium Stannate - 500 gm Germany/ UK or Equivalent

500 gm

38 Picric acid - 500 gm Germany/ UK or Equivalent

500 gm

40 Tartaric Acid - 500 gm Germany/ UK or Equivalent

500 gm

46 Starch (Powder) - 500 gm Pak/ China or Equivalent 500 gm

57 Methyle Orange - One pack Germany / UK or Equivalent

One pack

79 Zinc Chloride Germany / UK or Equivalent

500 gm

80 Zinc Nitrate Germany/ UK or Equivalent

500 gm

1 Steel Yard Apparatus-maximum load 5 KgGermany/ UK or

Equivalent 12

2 Winch Crab Single purchase Apparatus Grooved wheel of 25 cm diameter

Germany/ UK or Equivalent 12

3 Winch Crab double purchase Apparatus Grooved wheel of 25 cm diameter. Gears are Machine Cut

Germany/ UK or Equivalent 12

Total:Grand Total

Total:LIST OF CHEMICALS

Total:

Additional Items:-

56 Burette Stand Japan/ UK or Equivalent 1

52 Dropper Pak/ China or Equivalent 5

45 Burette - 50 ml France/ Germany or Equivalent 30

41

44 Conical flask - 250 ml France/ Germany or Equivalent 20

34 Test tube brush Good quality Pak/ China or Equivalent 5

32 Test Tube - 16 x 150 mm France/ Pak Made or Equivalent 200