GAZETTE 17-25 Dated 7 June 2017 · (d) frontal tape unwinders AND splicing unit; (e) frontal tape application AND cutting unit, including gluing module Op. 11.05.17 - TC 1748690 Stated

Commonwealth of Australia Gazette

No.TC17/25, Wednesday, 7 June 2017 Published by the Commonwealth of Australia

TARIFF CONCESSIONS

CONTENTS

TCO Applications ....................................................................................................... 2

TCO Applications Refused ........................................................................................ 7

TCOs Made.................................................................................................................. 8

Local Manufacturer Initiated - TCO Revocation Requests .................................. 11

Local Manufacturer Initiated - TCO Revocation Requests Refused ................... 12

Comptroller-General of Customs Initiated - Intention to Revoke Cancelled ..... 13

Local Manufacturer Initiated - TCOs Revoked ...................................................... 14

Local Manufacturer Initiated - TCOs Revoked and Re-Issued ............................ 16

Intention to Revoke TCOs not used in over 2 years ............................................. 18

TCOs Revoked - Unused for over 2 years ............................................................. 21

The Commonwealth of Australia Tariff Concessions Gazette (the Tariff Concessions Gazette) is free of charge on the DIBP

internet site at: http://www.border.gov.au/Busi/domestic-manufacturers-and-importers

The Tariff Concessions Administration Section is located at 5 Constitution Ave Canberra City 2601 Contact details: General Email Inquiries:……………………………[email protected] General Inquiries: ...............................................................(02) 6229 3567 TAPIN help desk: ................................................................(02) 6275 6534

Cat. No.

ISSN 0813-8389

©Commonwealth of Australia, 2017

http://www.border.gov.au/Busi/domestic-manufacturers-and-importers

2 TCO Applications Commonwealth of Australia Gazette

No TC17/25, Wednesday, 07 Jun 2017

TCO Applications

CUSTOMS ACT 1901 - NOTICE PURSUANT TO SECTION 269K(1) - APPLICATIONS MADE FOR TARIFF CONCESSION ORDERS

Applications have been lodged for Tariff Concession Orders for the goods described in the following TABLE.

Australian manufacturers who wish to contest the granting of a Tariff Concession Order for the goods described

are invited to lodge a submission in writing in an approved form. Submissions must be lodged within 50 days

of the date of publication of this Notice.

The operative date (Op.) and TC reference number follow the description of goods.

Objections to the making of TCO submission forms are available at

http://www.border.gov.au/Forms/Documents/b444.pdf

Contact: Email [email protected]

THE TABLE

Description of Goods including the Schedule 4 Item Number

Customs Tariff Classification General Duty Rate

5907.00.00 FABRICS, ASPHALT REINFORCEMENT GRID-COMPOSITE, bituminous

coated having NOT less than 60% bitumen, being EITHER of the

following:

(a) asphalt reinforced grid-composite, being knitted modulus

polyester yarns, having ALL of the following;

(i) tensile strength NOT LESS than 50 kN/m in machine

direction AND cross-machine direction;

(ii) residual strength NOT less than 80% of the

minimum tensile strength;

(iii) maximum elongation NOT greater than 12% at breaking

point;

(iv) aperture size 40 mm x 40 mm;

(v) non-woven polypropylene layer,

(b) asphalt reinforcement grid-composite, being knitted high

modulus polyvinyl-alcohol yarns, having ALL of the

following;

(i) tensile strength NOT less than 50 kN/m in machine

direction AND cross-machine direction;

(ii) residual strength NOT less than 80% of the minimum

tensile strength;

(iii) maximum elongation NOT greater than 6% at breaking

point;

(iv) aperture size 40 mm x 40 mm;

(v) polypropylene non-woven layer

Op. 26.04.17 - TC 1743607

Stated Use:

Reinforcement between or under layers of asphalt on roads,

runways and carparks to reduce reflective cracking

Applicant: HUESKER AUSTRALIA PTY LTD

50

5%

8421.99.90 PARTS, FILTER PRESS, being plates AND/OR frames

Op. 04.05.17 - TC 1745904

Stated Use:

Particulate removal from bio-plasma blood product suspension

Applicant: CSL BEHRING (AUSTRALIA) PTY LTD

50

5%

http://www.border.gov.au/Forms/Documents/b444.pdf





8422.30.90 BOTTLE RINSING AND FILLING AND SEALING AND LABELLING MACHINES,

including ALL of the following:

(a) mono block rinsers;

(b) fillers;

(c) cappers AND/OR corkers;

(d) labellers

Op. 04.05.17 - TC 1746327

Stated Use:

To bottle whisky and also whisky cream (liquer)

Applicant: TRANSITAINER (VIC) PTY LTD

50

5%

8422.30.90 MEDICAL PLASTIC SATCHEL FILLING, SEALING AND LABELLING MACHINES,

incorporating a printer, with OR without pill, ampoule, bottle

OR medical kit feeders

Op. 09.05.17 - TC 1747551

Stated Use:

To package pills, ampoules, bottles or medical kits in small

plastic satchels and print identification, alert and advice

information labels

Applicant: METROTUBE AUSTRALIA PTY LTD

50

5%

8428.39.00 CROSS CHAIN CONVEYORS, programmable logic controlled, with OR

without guiding fences, having ALL of the following:

(a) width NOT greater than 16 m;

(b) length NOT greater than 17.2 m;

(c) motor power NOT greater than 9 kW

Op. 08.05.17 - TC 1747418

Stated Use:

Movement and handling of panels and billets as part

of a cross laminated timber panel production process

Applicant: XLAM AUSTRALIA PTY LTD

50

5%

8428.90.00 PALLETISE AND DEPALLETISE HANDLING SYSTEM, SORT AND PICK, GAS

CYLINDER, programmable logic controlled, including ALL of the

following:

(a) 6-axis robot cell;

(b) gas cylinder transfer gantry robot including ALL of the

following:

(i) bridge unit;

(ii) vertical module;

(iii) gantry structure,

(c) robot grippers;

(d) robot controls;

(e) pallet AND/OR palletised gas cylinder turntables;

(f) gas cylinder pallets;

(g) fences AND doors AND safety barriers;

(h) electrical cabling AND cabinets

Op. 04.05.17 - TC 1746323

Stated Use:

The function of the automated, robotic handling plant is to

sort, pick, palletise and depalletise gas cylinders

Applicant: BOC LTD

50

5%





8428.90.00 STORAGE AND RETRIEVAL MACHINES, REEL AND/OR TRAY, having BOTH

of the following:

(a) barcode scanners;

(b) record keeping software

Op. 04.05.17 - TC 1746332

Stated Use:

Buffer storage unit used to record and store surface mount

device (SMD) reels and trays

Applicant: HW TECHNOLOGIES

50

5%

8428.90.00 ROTARY TABLES AND CONVEYOR BELTS, programmable logic controlled,

incorporating conveyed goods holding rails

Op. 10.05.17 - TC 1747838

Stated Use:

To transport goods in production lines such as transporting

pharmaceutical vials away from the vial filling and closing

machines for packing

Applicant: CSL BEHRING (AUSTRALIA) PTY LTD

50

5%

8477.59.00 EXPANDABLE POLYSTYRENE SHAPE MOULDING PLANT, including ALL of

the following:

(a) shape moulders;

(b) moulds;

(c) pre-expander;

(d) fluid bed;

(e) loading screw;

(f) granulator;

(g) deduster;

(h) hoppers;

(i) electrical controls;

(j) condensers;

(k) valves;

(l) filler guns;

(m) tanks;

(n) cooling fan;

(o) conveyors;

(p) pipes;

(q) hoists;

(r) unloaders;

(s) safety fences AND gates

Op. 03.05.17 - TC 1745727

Stated Use:

Manufacturing of 'waffle pods' used in concrete slab

construction from expandable polystyrene

Applicant: WAFFLE POD PTY LTD

50

5%

8479.89.90 CUTTING MACHINES, MEDICINE BLISTER PACK SHEET

Op. 09.05.17 - TC 1747765

Stated Use:

To cut medical pill blister pack sheets into uniform lengths

Applicant: METROTUBE AUSTRALIA PTY LTD

50

5%





8479.89.90 NAPPY CORE MACHINES, having ALL of the following:

(a) filtration unit;

(b) powder meters AND conveyors;

(c) core forming drum

Op. 11.05.17 - TC 1748671

Stated Use:

Nappy manufacturing

Applicant: ONTEX MANUFACTURING PTY LTD

50

5%

8479.89.90 CORE WRAPPING AND CUTTING MACHINES, NAPPY, having ALL of the

following:

(a) core wrap unwinding AND splicing module;

(b) acquisition layer unwinding AND splicing module;

(c) combined acquisition layer applicator AND core cutting

module, including gluing module

Op. 11.05.17 - TC 1748674

Stated Use:

Nappy manufacturing


50

5%

8479.89.90 NAPPY EAR FABRICATION AND APPLICATION MACHINE, having ALL of the

following:

(a) integrated nappy back ear unwinding AND splicing AND

shaping module;

(b) integrated nappy front ear unwinding and splicing module;

(c) integrated front ear transport AND application AND cutting

module, including gluing module;

(d) nappy back ear bonding unit;

(e) front ear shaping AND cutting unit;

(f) back ear shaping AND cutting unit;

(g) back ear transport AND application AND cutting unit,

including gluing module

Op. 11.05.17 - TC 1748678

Stated Use:

Nappy manufacturing


50

5%

8479.89.90 FOLDING AND CUTTING MACHINES, NAPPY

Op. 11.05.17 - TC 1748686

Stated Use:

Nappy manufacturing


50

5%

8479.89.90 TOP AND BACK SHEET MACHINES, NAPPY, having ALL of the

following:

(a) back sheet unwinding AND splicing unit;

(b) elastic unwinders;

(c) top sheet unwinding AND splicing unit;

(d) frontal tape unwinders AND splicing unit;

(e) frontal tape application AND cutting unit, including

gluing module

Op. 11.05.17 - TC 1748690

Stated Use:

Nappy manufacturing


50

5%





8479.89.90 PULL AND PRESS MACHINES, NAPPY

Op. 11.05.17 - TC 1748694

Stated Use:

Nappy manufacturing


50

5%

8479.89.90 MAKE UP CLAMPS, RISER CONNECTION, OIL AND/OR GAS WELL, hydraulic

rollers

Op. 15.05.17 - TC 1749304

Stated Use:

Pressurised connection on large diameter riser pipes in the oil

and gas industry

Applicant: SHELL AUSTRALIA PTY LTD

50

5%

8503.00.00 PARTS, ACTUATOR, electric, multi-turn, being a housing sub-

assembly consisting of ALL of the following:

(a) declutch lever;

(b) encoder;

(c) encoder drive cartridge;

(d) control panel;

(e) control module;

(f) terminal block;

(g) power board;

(h) main board;

(i) gear case AND electronics covers

Op. 04.05.17 - TC 1746334

Stated Use:

Parts for Valve Actuators to open and close valves which control

the flow of liquids

Applicant: ACRODYNE PTY LTD

50

5%

8536.50.99 SWITCHES, MICROPROCESSOR ADDRESSABLE, with OR without wiring,

having BOTH of the following:

(a) electric current rating NOT less than 60 mA and NOT

greater than 275 mA;

(b) voltage rating NOT less than 50 V and NOT greater

than 600 V

Op. 09.05.17 - TC 1747425

Stated Use:

To limit inadvertent detonations in mining operations

Applicant: SCHLUMBERGER AUSTRALIA PTY LTD

50

5%

8709.11.00 TROLLEYS, self-propelled, electro-hydraulic, remote controlled,


(a) rated load capacity NOT greater than 75 metric tonnes;

(b) platform width NOT greater than 3 metres;

(c) platform length NOT less than 8 metres

Op. 11.05.17 - TC 1748669

Stated Use:

Movement of heavy goods within a restricted space

Applicant: SHELL AUSTRALIA PTY LTD

50

5%

7 TCO Applications Refused Commonwealth of Australia Gazette


TCO Applications R efused

CUSTOMS ACT 1901

NOTICE PURSUANT TO SECTION 269R(1) - APPLICATIONS FOR TARIFF CONCESSION ORDERS REFUSED

The application for the Tariff Concession Order for the goods described in the following TABLE has been

refused.


THE TABLE


Customs Tariff Classification

8438.80.00 MIXERS, programmable logic controlled, including ALL of the

following:

(a) mixing chamber volume capacity NOT less than 1 000 L;

(b) mixer motor;

(c) heating AND cooling jacket;

(d) agitator;

(e) vacuum pump;

(f) bin elevator;

(g) discharge pump

Op. 30.11.16 - TC 1674249

Reason for refusal:

Substitutable goods produced in Australia in the ordinary course

of business by Inox Fabrications Australia Pty Ltd, Epping, Vic

50

8 TCOs Made Commonwealth of Australia Gazette


TCOs M ade

CUSTOMS ACT 1901 - NOTICE PURSUANT TO SECTION 269R(1) - TARIFF CONCESSION ORDERS MADE

Tariff Concession Orders have been made for the goods described in the following TABLE.

The operative date (Op.) and TC reference No. follow the description of goods. Local manufacturers of

substitutable goods may request the revocation of TCOs at any time.


THE TABLE



3506.91.90 TAPE, double side adhesive, having ALL of the following:

(a) tissue paper backing;

(b) polyethylene liner paper;

(c) acrylic OR rubber base glue

Op. 28.02.17 Dec. date 31.05.17 - TC 1724280

50

3926.90.90 BAGS, BIOREACTOR, having connection tubes

Op. 28.02.17 Dec. date 31.05.17 - TC 1724490

50

7302.10.00 RAIL TRACK SYSTEM, PAPERBOARD TRANSFER CAR, including ALL of the

following:

(a) rails with mounting brackets;

(b) bearing plates;

(c) stoppers

Op. 15.02.17 Dec. date 30.05.17 - TC 1721412

50

7326.90.90 FLUE GAS DUCTS, RECUPERATOR, GAS RECOVERY SYSTEM, including ALL

of the following:

(a) modules;

(b) flanges;

(c) adapters;

(d) plates;

(e) shims;

(f) compensator

Op. 02.03.17 Dec. date 02.06.17 - TC 1725296

50

7326.90.90 PALLET INLOADERS, with OR without ANY of the following:

(a) stabiliser with OR without braces;

(b) safety pins;

(c) stanchions AND/OR struts;

(d) supports, metal AND/OR wood AND/OR rubber;

(e) document compartment

Op. 14.03.17 Dec. date 02.06.17 - TC 1728231

50

8412.90.90 PARTS, HYDRAULIC MOTOR, downhole, being lower assemblies


(a) transmission;

(b) fixed bend housing;

(c) driveshaft sub-assembly including ALL of the following:

(i) bearings;

(ii) catch;

(iii) spacers,

(d) stator adaptor housing

Op. 03.03.17 Dec. date 02.06.17 - TC 1725509

50

8421.29.90 WASTE WATER AND SLURRY FILTRATION AND SEPARATOR MACHINES,


(a) vibrating screen;

(b) water spray bars;

(c) screen mats;

(d) sump;

(e) pump;

(f) hydrocyclone;

(g) dewatering screen

Op. 08.03.17 Dec. date 31.05.17 - TC 1726837

50





8421.39.90 CONTAMINATION ABATEMENT GAS TREATMENT PLANT, including ALL of

the following:

(a) inorganic pollutant AND gas scrubbers with ejectors;

(b) trichlorosilane scrubber;

(c) adsorber;

(d) valves;

(e) pH AND flow analysers;

(f) pumps;

(g) pressure AND flow AND filling controls;

(h) regenerative thermal oxidiser

Op. 23.02.17 Dec. date 31.05.17 - TC 1723162

50

8427.10.00 TRANSFER TRUCKS, HOSPITAL BED, battery powered

Op. 14.03.17 Dec. date 31.05.17 - TC 1728222

50

8428.90.00 SUBSEA PIPELINE REPAIR MACHINES, being EITHER of the following:

(a) pipeline tool pushing AND pulling machines;

(b) pipeline alignment AND/OR lifting frames, hydraulically

operated, having ALL of the following:

(i) remotely operated vehicle interface panel;

(ii) hydraulic cylinders;

(iii) claw pipe grapple;

(iv) skirted foundation box;

(v) mud securing steel mats, with OR without hydraulic

actuated rails;

(vi) pipe spool deployment guides

Op. 23.02.17 Dec. date 31.05.17 - TC 1723159

50

8428.90.00 TURNSTILES, STEEL COIL STORAGE

Op. 08.03.17 Dec. date 31.05.17 - TC 1726838

50

8428.90.00 BRIDGE STACKERS, STEEL COIL, having a maximum lifting capacity

of 5 000 kg per coil

Op. 14.03.17 Dec. date 02.06.17 - TC 1728217

50

8428.90.00 COIL CARS, STEEL SLITTING LINE, being ANY of the following:

(a) flexible coil storage cars;

(b) fixed coil storage saddle cars;

(c) entry coil cars;

(d) exit coil cars

Op. 16.03.17 Dec. date 02.06.17 - TC 1729043

50

8431.39.00 PARTS, ARMOURED FACE MINING CONVEYOR, being dumbbell shaped

connector assemblies, consisting of ALL of the following:

(a) dumbbell shaped connector;

(b) linchpins;

(c) retainers

Op. 23.02.17 Dec. date 31.05.17 - TC 1723052

50

8438.20.00 CHOCOLATE MANUFACTURING LINE, having ALL of the following:

(a) raw material handling AND transfer AND storage AND

pigging stations;

(b) storage vessels;

(c) mixers;

(d) blending AND dosing station;

(e) chocolate refiners AND conches stations;

(f) transfer pumps;

(g) storage tanks;

(h) piping

Op. 07.03.17 Dec. date 02.06.17 - TC 1726515

50





8474.10.00 PULSATING JIG ASSEMBLIES, MINERAL ORE PROCESSING PLANT,


(a) jig sumps;

(b) screens;

(c) control panel;

(d) screen vibrators;

(e) jig frame;

(f) sprayers;

(g) pumps

Op. 06.03.17 Dec. date 31.05.17 - TC 1726088

50

8479.89.90 WASTE SEPARATION MACHINES, including ALL the following:

(a) vacuum OR blower;

(b) diesel OR hydraulic OR electric powered fan;

(c) vacuum OR blower head connector,

with OR without hoses

Op. 23.02.17 Dec. date 31.05.17 - TC 1723302

50

8479.89.90 SHOCK ABSORBERS, VISCOELASTIC VIBRATION DAMPING, including BOTH

of the following:

(a) viscous fluid, being ANY of the following:

(i) bitumen;

(ii) polybutene;

(iii) silicone based,

(b) top plate mounted piston

Op. 08.03.17 Dec. date 31.05.17 - TC 1726836

50

8483.40.90 PUMP DRIVES, PROGRESSIVE CAVITY PUMPING, top mount, electric

AND/OR hydraulic, complying with International Standard 15136-2

(ISO 15136-2), being belt OR gear driven, having ANY of the

following:

(a) motor;

(b) stuffing box;

(c) fittings;

(d) adapter plates AND flex couplings;

(e) low stuffing box pressure switch;

(f) tachometer;

(g) stand;

(h) polished rod hold down hook;

(i) mechanical AND/OR hydraulic braking

Op. 15.02.17 Dec. date 31.05.17 - TC 1721331

50

8504.40.90 CHARGERS, COMPUTER TABLETS, electromagnetic induction

Op. 24.02.17 Dec. date 31.05.17 - TC 1723470

50

9028.20.10 WATER METERS, TURBINE, nominal size DN being ANY of the

following:

(a) 40;

(b) 50;

(c) 65;

(d) 80;

(e) 100;

(f) 150

Op. 02.03.17 Dec. date 31.05.17 - TC 1725016

50

11 Local Manufacturer Initiated - TCO Revocation Requests Commonwealth of Australia Gazette


Local M anufac tur er Initiated - TC O R evocation R equests

NOTIFICATION OF AN AUSTRALIAN INDUSTRY REVOCATION REQUEST - SECTION 269SC(1A) CUSTOMS ACT

An application has been lodged for revocation of the Tariff Concession Order set out in the following TABLE.

The Lodgement Request Date shown in the table below is the intended revocation date for the Tariff Concession

Order which will take effect should the application for revocation be successful.

Importations not covered by in-transit provisions may be subject to post action as any decision to revoke an

order is backdated to the date of request for revocation.


THE TABLE


Customs Tariff Classification Lodgement Request Date

8705.90.00 TRUCKS, incorporating ALL of the following:

(a) compression ignition engine;

(b) view cameras;

(c) spray bars;

(d) brushes;

(e) water blasting machine

Op. 23.01.17 Dec. date 18.04.17 - TC 1708451

50

26.05.17

12 Local Manufacturer Initiated - TCO Revocation Requests Refused Commonwealth of Australia Gazette


Local M anufac tur er Initiated - TC O R evocation R equests Refused

CUSTOMS ACT 1901

NOTICE PURSUANT TO SECTION 269SE(1) - REFUSAL TO REVOKE A TARIFF CONCESSION ORDER CUSTOMS ACT 1901

The Request for revocation of Tariff Concession Orders for goods described in the following TABLE have been

refused.


THE TABLE



8402.90.00 PARTS, STEAM GENERATION WATER-TUBE BOILER, ALUMINA PLANT, being

ANY of the following:

(a) buckstays;

(b) downcomers;

(c) headers;

(d) tubes or pipes, cut to shape;

(e) inner casings;

(f) pipe assemblies, being ANY of the following:

(i) roofs;

(ii) floors;

(iii) noses;

(iv) panels

Op. 13.01.09 - TC 0900688

50

8402.90.00 PARTS, STEAM GENERATOR, POWER GENERATION PLANT, being ANY of the

following:

(a) inlet transition duct unit;

(b) inlet plenum;

(c) exhaust hood unit;

(d) stack adapter;

(e) exhaust stack unit;

(f) once through steam generator AND ducting erection joint

assembly kits, consisting of BOTH of the following:

(i) sheet metal sealing strips AND fastenings;

(ii) insulation,

(g) piping, valves AND instrumentation consisting of ALL of

the following:

(i) high pressure AND low pressure vent stack;

(ii) high pressure steam outlet piping;

(iii) low pressure steam outlet piping;

(iv) pilot-operated relief valve piping;

(v) high pressure feedwater inlet piping;

(vi) low pressure feed water inlet piping

Op. 06.01.16 - TC 1600940

50

8403.90.00 PARTS, INDUSTRIAL GLASSHOUSE WETBACK BOILER, being ANY of the

following:

(a) tanks;

(b) shell and crown rings;

(c) spray tubes;

(d) overflows;

(e) manholes

Op. 23.08.10 - TC 1038767

50

8404.10.00 AUXILIARY PLANT, STEAM BOILER, being superheater attemperators

with supports

Op. 04.01.11 - TC 1100392

50

13 Local Manufacturer Initiated - TCO Revocation Requests Refused and

Comptroller-General of Customs Initiated - Intention to Revoke

Cancelled

Commonwealth of Australia Gazette




8404.90.00 PARTS, STEAM GENERATION BOILER AUXILIARY PLANT, being ANY of the

following:

(a) plates;

(b) chock liners;

(c) supports;

(d) fluid accumulators;

(e) junction boxes (non-electrical);

(f) control devices

Op. 18.02.08 - TC 0802705

50

Comptroller-Gener al of C ustoms Initi ated - Intention to R evoke C ancelled

CUSTOMS ACT 1901

CANCELLATION OF THE INTENTION TO REVOKE

The Request for revocation of the Tariff Concession Order for goods described in the following TABLE has been

cancelled.


THE TABLE



3926.90.90 PACKERS, GROUT HOLE, expandable pressurised injection

Op. 30.09.05 Dec. date 23.12.05 - TC 0513347

50

14 Local Manufacturer Initiated - TCOs Revoked Commonwealth of Australia Gazette


Local M anufac tur er Initiated - TC Os R evoked

CUSTOMS ACT 1901 - NOTICE PURSUANT TO SECTION 269SE(1) - AUSTRALIAN INDUSTRY INITIATED - TARIFF CONCESSION

ORDERS REVOKED

The Tariff Concession Orders for the goods described in the following TABLE have been revoked.


THE TABLE


Customs Tariff Classification Last Date of Effect

8402.12.00 BOILERS, WATERTUBE, STEAM, solid fuel, having BOTH of the

following:

(a) heat output NOT greater than 5 000 kW;

(b) mechanical stoker

Op. 20.03.09 Dec. date 05.06.09 - TC 0909455

Substitutable goods produced in Australia in the ordinary

course of business by W. Simons & Sons (Aust) Pty Ltd,

Alexandria, NSW. In transit provisions apply

50

04.04.17

8402.19.00 VAPOUR GENERATORS, CONCRETE CURING, having ALL of the following:

(a) generator output NOT greater than 450 kW;

(b) water cooled combustion chamber;

(c) water cooled pre-mix burner;

(d) temperature sensors AND controllers;

(e) noise insulated enclosure

Op. 19.01.16 Dec. date 11.04.16 - TC 1602954




50

17.04.17

8402.20.00 BOILERS, STEAM, SUPERHEATED, HIGH PRESSURE

Op. 29.09.06 Dec. date 15.12.06 - TC 0615151




50

17.04.17

8403.10.00 BOILERS, HOT WATER, STOKER FED SOLID FUEL, having ALL of the

following:

(a) heat output NOT greater than 300 kW;

(b) mechanical stoker and hearth access;

(c) adjustable heating surface area

Op. 21.02.08 Dec. date 16.05.08 - TC 0803012




50

04.04.17

8403.10.00 BOILERS, HOT WATER, solid fuel, having ALL of the following:

(a) power NOT greater than 1 000 kW;

(b) stoker;

(c) tube cleaner;

(d) ash remover

Op. 19.11.09 Dec. date 05.02.10 - TC 0943670




50

04.04.17

15 Local Manufacturer Initiated - TCOs Revoked Commonwealth of Australia Gazette




8403.10.00 GREENHOUSE CENTRAL HEATING BOILERS, diesel, having ALL of the

following:

(a) heating capacity NOT less than 25 000 square metres;

(b) chimney;

(c) pipes;

(d) control panels;

(e) water pumps

Op. 13.01.12 Dec. date 02.04.12 - TC 1201625




50

04.04.17

8403.10.00 HYDRONIC HOT WATER HEATING PLANT, biomass solid fuel,

programmable logic controlled, including ALL of the following:

(a) conveyors;

(b) furnace;

(c) fans;

(d) de-ashing boiler module;

(e) boilers;

(f) combustion pre-heater;

(g) emission control module;

(h) flues

Op. 21.11.13 Dec. date 10.02.14 - TC 1338996




50

04.04.17

16 Local Manufacturer Initiated - TCOs Revoked and Re-Issued Commonwealth of Australia Gazette


Local M anufac tur er Initiated - TC Os R evoked and Re-Issued

CUSTOMS ACT 1901

NOTICE PURSUANT TO SECTION 269SE(1)&(2) - TARIFF CONCESSION ORDERS REVOKED AND NEW TARIFF CONCESSION ORDERS

MADE

Tariff Concession Orders for the goods described in the following TABLE have been revoked and new Tariff

Concession Orders have been made in respect of the goods described below.

The operative date (Op.), decision date (Dec. date) and TC reference number follow the description of goods.

In-transit provisions apply.


THE TABLE



TCO REVOKED

8402.19.00 GENERATORS, PURE STEAM, including ALL of the following:

(a) separator columns;

(b) valves;

(c) sensors

Op. 11.04.12 Dec. date 02.07.12 - TC 1211650


course of business by W. Simons & Son (Aust) Pty Ltd,

Alexandria, NSW. TCO 1211650 revoked and reissued as TC

1757420. In transit provisions apply

50

04.04.17

TCO REISSUED

8402.19.00 GENERATORS, PURE STEAM, stainless steel construction, including

ALL of the following:

(a) separator columns;

(b) valves;

(c) sensors

Op. 05.04.17 Dec. date 02.06.17 - TC 1757420

50

TCO REVOKED

8404.10.00 AUXILIARY PLANT, STEAM GENERATION BOILER, comprising ANY of the

following:

(a) windboxes;

(b) furnace walls, being water or convection;

(c) superheaters, preheaters or airheaters;

(d) sootblowers;

(e) ash handlers;

(f) deaerators;

(g) coal bunkers;

(h) steam drums;

(i) tanks, being flash, pressure or blowdown vessels;

(j) attemperators

Op. 10.06.10 Dec. date 05.08.10 - TC 1034450



Alexandria, NSW.TCO 1034450 revoked and reissued as TC 1757417.

In transit provisions apply

50

04.04.17

mailto:[email protected]

17 TCOs Revoked - Unused for over 2 years Commonwealth of Australia Gazette




TCO REISSUED

8404.10.00 AUXILIARY PLANT, STEAM GENERATION BOILER, comprising ANY of the

following:

(a) windboxes;

(b) superheaters, preheaters or airheaters;

(c) sootblowers;

(d) attemperators

(e) ash handlers;

(f) deaerators;

(g) coal bunkers

Op. 05.04.17 Dec. date 02.06.17 - TC 1757417

50

18 Intention to Revoke TCOs not used in over 2 years Commonwealth of Australia Gazette


Intention to Revoke TC Os not used i n over 2 years

TARIFF CONCESSION ORDERS (TCOs) NOT USED IN THE PREVIOUS 2 YEARS

The Comptroller-General of Customs is satisfied that the TCOs listed in the table below are no longer required

because, in the 2 years preceding the day of this notice, they have not been quoted in an import declaration

to secure a concessional rate of duty.

From Thursday, 6 July 2017, it is intended to take action to revoke these Orders under subsection 269SD (1A)

of the Customs Act 1901. In accordance with subsection 269SG (2) of the Customs Act 1901, in transit

provisions shall apply. If revoked, the expected date of effect will be 5 July 2017.

Interested parties are invited to provide, by close of business, Wednesday 5 July 2017, written reasons why an

Order should NOT be revoked.

Please advise if any of the Orders listed below have been quoted on an import declaration.

If a request is made to retain an Order used for the granting of a Determination, please specify the

Determination and the linked Item number to enable mapping to the Order and its scope.

THE TABLE

______________________________________________________________________________________________________________

Tariff

Classification Description Concession Number

______________________________________________________________________________________________________________

3926.90.90 WALL DECORATIONS, SILHOUETTE, depicting cartoon characters

Op. 28.02.02 Dec. date 24.05.02 - TC 0201801

3926.90.90 WALL HOOKS, plastic, incorporating children’s cartoon character

Op. 06.01.03 Dec. date 14.03.03 - TC 0300133

5907.00.00 FABRIC, cotton OR polyester base cloth, flock coated on one side,

consisting of an embossed flock finish of rayon pile of 0.8 to

1.0 denier (both inclusive)

Op. 02.08.01 Dec. date 28.12.01 - TC 0106712

5911.90.90 PAPER DRYER FABRIC, synthetic, unfinished, having ALL of the

following:

(a) warp density NOT less than 110 yarn/dm but NOT exceeding

350 yarn/dm;

(b) pick count of NOT less than 40 yarn/50 mm but NOT exceeding

120 yarn/50 mm;

(c) monofilament having a cross section diameter of NOT less than

0.40 mm but NOT exceeding 1.00 mm

Op. 15.11.97 Dec. date 12.06.02 - TC 0204922

6006.31.00 FABRIC, knitted, 0.1 denier fibre

Op. 01.01.02 Dec. date 14.01.02 - TC 0108354

6305.32.00 CONTAINERS, FLEXIBLE INTERMEDIATE BULK, compliant with

AS 3668 1989, and the Australian Code for the transport

of dangerous goods by road and rail, comprising ALL of the

following:

(a) single point lift with a double sewn protective sleeve;

(b) container body U.V. treated circular woven polypropylene;

(c) open top;

(d) container having star sewn closed bottom;

(e) low density polyethylene bottleneck type suspended liner

with breather patches and holes;

(f) safe working load of NOT less than 1 200 kg

Op. 19.12.03 Dec. date 31.03.04 - TC 0315793



6815.99.00 LADLE SIDE INJECTION DEVICES, refractory gas or reagent, having four

or more treatment ports, with or without injection lances

Op. 28.10.93 Dec. date 04.02.94 - TC 9312650

7323.93.00 COFFEE PERCOLATORS, stovetop, complete with 18/8 grade stainless

steel pump and basket

Op. 29.10.93 Dec. date 04.02.94 - TC 9312673

8413.50.10 PUMPS, TRIPLE PLUNGER (TRIPLEX), having ALL of the following:

(a) output flow greater than 500 litres/minute;

(b) working pressure greater than 30 000 kPa (300 bar);

(c) plunger stroke greater than 125.0 mm

Op. 06.02.03 Dec. date 02.05.03 - TC 0301206

8439.99.00 HEAD BOX TURBULENCE FLOW SHEETS, of graphite composite OR

poly-carbonate

Op. 06.06.01 Dec. date 24.08.01 - TC 0104646

8451.80.00 HEAT SETTING LINE, CARPET YARN, comprising ALL of the following:

(a) yarn creel;

(b) yarn prefeeder;

(c) heat setting chamber;

(d) yarn dryer;

(e) yarn accumulator;

(f) friezing machine

Op. 19.05.00 Dec. date 28.07.00 - TC 0004873

8474.39.00 MIXERS, COUNTER CURRENT, comprising ALL of the following:

(a) inclined counter rotating mixing pan with an outside diameter

NOT less than 2.5 metre/s and height NOT less than 1 metre/s;

(b) self-cleaning, having wall and bottom scrapers;

(c) self-discharging;

(d) rotating mixing tool with a speed NOT less than 300 rpm;

(e) mixing tool drive motor greater than 150 kw;

(f) mixing cycle time NOT greater than 3 minutes at 1.5 tonnes

per batch

Op. 04.12.03 Dec. date 15.04.04 - TC 0315321

8477.59.00 CAPSULE MAKER, BOTTLE

Op. 30.04.03 Dec. date 25.07.03 - TC 0305028

8479.89.90 WHEEL AND TYRE MOUNTING LINES, computer controlled

Op. 12.08.02 Dec. date 25.10.02 - TC 0207215

8481.80.90 VALVES, BLAST FURNACE, being ANY of the following:

(a) hot blast valves;

(b) waste OR mixed gas shut off valves;

(c) cold blast shut off valves;

(d) cold blast valves

Op. 27.06.01 Dec. date 07.09.01 - TC 0105142

8481.80.90 SLIDING GATE MACHINES, STEEL LADLE

Op. 15.02.02 Dec. date 10.05.02 - TC 0201393

8481.80.90 CHRISTMAS TREES, HORIZONTAL, SUBSEA WELL

Op. 18.06.02 Dec. date 06.09.02 - TC 0205188

3926.90.90 TRANSPARENCIES, COMPUTER PRINTER OR PRINTER-PLOTTER

Op. 22.02.00 Dec. date 12.05.00 - TC 0001947



8483.90.00 PARTS, STEEL STRIP ROLLING MILL ROLL END COUPLINGS, being ANY of

the following:

(a) roll end casings;

(b) drive end casings;

(c) lip or glyd seal retainer housings;

(d) spindles;

(e) gear rings;

(f) hub gears;

(g) thrust buttons;

(h) buffer rings;

(i) spring stops

Op. 14.03.01 Dec. date 25.05.01 - TC 0102346

8483.90.00 PARTS, STEEL STRIP ROLLING MILL ROLL END COUPLINGS, being ANY of

the following:

(a) thrust plates;

(b) spring guides;

(c) drive end ring gears;

(d) seal retainers and seal housings;

(e) spherical bushings and spherical rings;

(f) end plates,

but NOT including ANY parts for couplings with a motor power

rating of less than 4 100 kilowatts

Op. 22.05.01 Dec. date 23.10.01 - TC 0104261

8501.53.00 MOTORS, AC, MULTIPHASE, SQUIRREL CAGE, purged and pressurised,

having an output exceeding 500kW

Op. 11.02.00 Dec. date 28.04.00 - TC 0001649

8516.29.00 HEATERS, FLOOR STANDING, domestic, comprising ALL of the following:

(a) height NOT greater than 36 cms;

(b) width NOT greater than 24 cms;

(c) power consumption NOT greater than 1 700 watts;

(d) gross weight NOT greater than 3.5 kgs;

(e) ceramic elements

Op. 17.04.03 Dec. date 11.07.03 - TC 0304251

9001.10.00 FIBRES, OPTICAL, non-zero dispersion shifted, conforming

to ITU-T G.655

Op. 13.09.02 Dec. date 13.12.02 - TC 0208495

9506.99.90 GAME OR SPORT STANDARDS, being posts, with ratchet tensioning reel

Op. 03.04.02 Dec. date 21.06.02 - TC 0202734

9603.90.00 SWEEPERS, FLOOR, with electrostatic cloth covers of non-woven

polyester fibre

Op. 23.04.01 Dec. date 29.06.01 - TC 0103429



TCOs R evoked - U nused for over 2 years

CUSTOMS ACT 1901

NOTICE PURSUANT TO SECTION 269SE(2) - TARIFF CONCESSION ORDER REVOCATION AT THE INITIATIVE OF THE COMPTROLLER-

GENERAL OF CUSTOMS

The Tariff Concession Orders listed in THE TABLE below have has not been used for at least 2 years and have

been revoked under Section 269SD(1A). In transit provisions apply.

The intention to revoke these orders was notified in Gazette TC17/19 dated 26 April 2017.


THE TABLE



3920.99.00 TAPE, SWELLING, acrylate polymers in rolls

Op. 22.12.05 Dec. date 22.03.06 - TC 0605481

2 Years non use. In transit provisions apply

50

23.05.17

3926.90.90 LINERS, CONCRETE, HIGH DENSITY POLYETHYLENE OR POLYPROPYLENE,

THERMOPLASTIC, having BOTH of the following:

(a) conical anchor studs on one side;

(b) thickness NOT less than 2.0 mm and NOT greater than 10 mm

Op. 17.03.06 Dec. date 09.06.06 - TC 0605450


50

23.05.17

4016.99.00 BELLOWS, FUME EXHAUST, PICKLE LINE TANK

Op. 24.04.06 Dec. date 14.07.06 - TC 0607300


50

23.05.17

5603.12.00 FABRIC, comprising BOTH non-woven polypropylene AND

polypropylene microhook film

Op. 16.02.06 Dec. date 21.04.06 - TC 0603913


50

23.05.17

8417.10.00 FURNACES, SLAG, comprising ALL of the following:

(a) sootblowers;

(b) heat exchangers;

(c) waste heat boilers;

(d) condensers;

(e) coal mills;

(f) recuperators;

(g) cooling towers;

(h) blowers;

(i) dewatering bins;

(j) ladles;

(k) crane;

(l) dust collectors;

(m) rotary kilns;

(n) refractories;

(o) scrubbers;

(p) coolers;

(q) thickeners;

(r) cyclones;

(s) grinding mills

Op. 08.02.06 Dec. date 28.04.06 - TC 0603545


50

23.05.17





8417.80.00 OVENS, FINISH, CONTINUOUS PAINT LINE, having ALL of the

following:

(a) NOT less than three heating zones;

(b) metal throughput greater than 33 000 kg/hour;

(c) natural gas fired

Op. 21.03.06 Dec. date 02.06.06 - TC 0605458


50

23.05.17

8417.80.00 OVENS, PRIME, CONTINUOUS PAINT LINE, having ALL of the following:

(a) four heating zones;

(b) metal throughput NOT less than 33 000 kg/hour;

(c) maximum solvent load NOT greater than 300 litres/hour;

(d) recirculation flow NOT less than 160 000 cubic metres/hour;

(e) natural gas fired

Op. 03.05.06 Dec. date 21.07.06 - TC 0607779


50

23.05.17

8417.90.00 PARTS, FINISH OVENS, CONTINUOUS PAINT LINE, being ANY of the

following:

(a) flashings;

(b) ducts;

(c) bases;

(d) air and/or distribution boxes;

(e) filler plates;

(f) lifting lugs;

(g) gaskets;

(h) rail guard supports;

(i) quench partitions

Op. 06.04.06 Dec. date 30.06.06 - TC 0606245


50

23.05.17

8417.90.00 PARTS, PRIME OVENS, CONTINUOUS PAINT LINE, being ANY of the

following:

(a) insulated panels;

(b) ducts;

(c) frames;

(d) burner supports;

(e) insulation;

(f) inside roof flashes and/or floor flashes;

(g) exhausts

Op. 03.05.06 Dec. date 28.07.06 - TC 0607776


50

23.05.17

8419.50.90 NIOBIUM SHELL AND TUBE HEAT EXCHANGERS, PICKLE LINE

Op. 13.02.06 Dec. date 28.04.06 - TC 0603729


50

23.05.17

8428.90.00 LOADING AND/OR UNLOADING STATIONS, ANODISING LINE

Op. 08.02.06 Dec. date 21.04.06 - TC 0603549


50

23.05.17

8428.90.00 FEEDERS AND WEIGHERS, bentonite

Op. 11.04.06 Dec. date 07.07.06 - TC 0606865


50

23.05.17

8479.50.90 ROBOTICS, LABORATORY, MICRO ORGANISM PICKERS, having BOTH of the

following:

(a) image analyser;

(b) single picking head containing NOT less than 96 picking pins

Op. 01.03.06 Dec. date 19.05.06 - TC 0604625


50

23.05.17





8479.89.90 TRAPS, MAGNETIC, PULP MAKING OR RECONSTITUTING

Op. 15.03.06 Dec. date 02.06.06 - TC 0605330


50

23.05.17

8479.89.90 CIRCULATORS, OIL, STEAM TURBINE, comprising ALL of the following:

(a) storage tank;

(b) centrifugal pumps;

(c) control valves;

(f) oil filters;

(e) oil cooler

Op. 23.03.06 Dec. date 16.06.06 - TC 0605621


50

23.05.17

8479.89.90 SETTERS AND CAPPERS, PLUG, AUTOMOTIVE BATTERY, programmable

logic control

Op. 28.03.06 Dec. date 23.06.06 - TC 0605754


50

23.05.17

8479.89.90 PARTS, CONTINUOUS PAINT LINE, STEEL STRIP, being ANY of the

following:

(a) uncoilers with hold down roll;

(b) recoilers;

(c) accumulator and accumulator columns;

(d) outboard bearings

Op. 07.04.06 Dec. date 30.06.06 - TC 0606252


50

23.05.17

8479.89.90 CARTS, ROLL, SCISSOR TYPE, CONTINUOUS STEEL STRIP PAINT LINE

Op. 03.05.06 Dec. date 21.07.06 - TC 0607766


50

23.05.17

8481.80.90 DAMPERS, MOTORISED, PRIME AND/OR FINISH OVEN, CONTINUOUS PAINT

LINE

Op. 21.03.06 Dec. date 02.06.06 - TC 0605340


50

23.05.17

8481.80.90 VALVES, RECIRCULATION, PICKLE LINE TANK, being ANY of the

following:

(a) pressure gauge isolation ball valves and/or pressure

transmitter isolation ball valves;

(b) acid drain ball valves;

(c) shut-off valves

Op. 24.04.06 Dec. date 14.07.06 - TC 0607299


50

23.05.17

8481.90.90 BODIES, VALVE, HOT BLAST

Op. 01.05.06 Dec. date 21.07.06 - TC 0607588


50

23.05.17

8483.60.90 DRIVE SHAFTS, CHARGE ROLLER TABLE, WALKING BEAM FURNACE, having

BOTH of the following:

(a) length NOT less than 600 mm;

(b) diameter NOT less than 220 mm

Op. 06.04.06 Dec. date 30.06.06 - TC 0606251


50

23.05.17





8484.20.00 SEAL SETS, OIL FILM BEARING, consisting of All of the following:

(a) neck seal with band;

(b) seal end plate;

(c) seal inner ring;

(d) deflector ring;

(e) coolant seal;

(f) screws;

(g) round body ring;

(h) bumper

Op. 10.03.06 Dec. date 26.05.06 - TC 0605044


50

23.05.17

8705.90.00 CONVEYORS, MATERIAL, VEHICLE MOUNTED

Op. 13.04.06 Dec. date 30.06.06 - TC 0606993


50

23.05.17