Garage doors - Teckentrupteckentrup.co.za/.../south-africa/...garage_doors.pdf · Garage sectional doors and side doors Product Ordering dimensions width/height in mm (modular dimensions)

Garage doors

4

® Program overview

Up-and-over garage doors and side doors Product Ordering dimensions

width/height in mm (modular dimensions)

Min. headroom Min. lateral projection left/right

Page

Up-and-over door DL W 1750 – 3000 mm H 1875 – 2750 mm

5-6

Up-and-over door DF (double garage door)

W max. 3000 / 5000 mm H max. 2750 / 2250 mm

80 mm / 100 mm (for modular width 5000 mm)

120 / 120 mm 200 / 200 mm (for modular width 5000 mm)

7-8

Garage side door ew-1 (steel hollow profile)

W 875 – 1250 mm H 1875 – 2375 mm

9-10

Garage side door ew-2 (steel hollow profile)

W 1350 – 2500 mm H 1750 – 2250 mm

11-12

Garage side door RP-1 (single-walled)

W 750 – 1350 mm H 1750 – 2500 mm

13-14

Garage side door RP-2 (single-walled)

W 1500 – 3000 mm H 1750 – 3000 mm

15-16

Garage sectional doors and side doors

Product Ordering dimensions width/height in mm (modular dimensions)

Min. headroom Min. lateral projection left/right

Page

Sectional door Type GSW 40-S

W 2250 – 5000 mm H 2000 – 2250 mm

120 mm with drive 240 mm for manual operation

82.5 mm 17-18

Sectionaltor Type GSW 40-L

W 2000 – 5500 mm H 1875 – 3000 mm


82.5 mm 19-20

Sectional door Type GSH

W 2000 – 5000 mm H 1875 – 3000 mm


82.5 mm 21-22

Sectional door side door Type GSW 40-L

W 875 – 1400 mm H 1925 – 2550 mm

23-24

Sectional door side door Type GSH

W 908 – 1400 mm H 1925 – 2400 mm

25-26

Garage door drives drive system 12.2; 20.2; 40.2

27

Subject to technical changes. 5

® Up-and-over garage door DL

Text example Compile and tender according to requirements. Please refer to technical data below for respective details. Updated 1st June 2015

Technical data Product: Up-and-over garage door DL

Installation in: Masonry Concrete

Dimensions: Width: 1750 – 3000 mm Height: 1875 – 2500 mm

Handing: Pre-assembled up-and-over garage door for handing behind or in the opening.

Door leaf: Door leaf frame: 3-sided galvanized block frame Reinforcement: 2 reinforcements, 1 mm thick Filling:

Ribbed door: galvanized sheet steel, vertically ribbed, optionally horizontally ribbed.

Panelled door (Georgian/cassette) made of galvanized thin sheet. Panelled door: galvanized sheet steel 1 mm thick. Wooden door: type of wood, vertical Norway

spruce, optionally horizontal or fishbone, door leaf frame without plinth.

Special equipment - filling: Steel panels with ventilation openings,

Corrugated grille Horizontal Norway spruce panels, Wooden fishbone panels with mullion

Door leaf thickness: 50 mm

Frame: 3-sided galvanized block frame with ceiling guide rail. Block frame with groove and PVC contact strip. Lateral lever arms with 3-fold spring system and finger pinch protection. Lateral plastic cover strips. 3 wall anchor plugs on each side and 1 x top, 2 threshold anchors

Surface: Ribbed/Panelled door: powder coated Traffic white, similar to RAL 9016.

Panelled door (Georgian/cassette) woodgrain, powder coated Traffic white,

similar to RAL 9016. Special coating for ribbed and panelled doors: trend colours RAL of your choice

(Avoid dark colours for doors subject to direct sunlight, since cracks and warpage of the door leaf cannot be completely prevented. Pearl-effect, fluorescent and metallic colours are only possible after individual clarification.)

Wooden door: vertical Norway spruce, optionally horizontal or fishbone. Door leaf frame without plinth, powder coated Sepia brown (RAL 8014). The wood has been factory protected against fungal decay, decay and wood pests with a colourless impregnating solution. Final treatment is carried out by the customer with a final protective coat.

Fittings: Spring-loaded special lock with profile half cylinder, lateral lock with special plastic catches.

Black plastic round handle with pull cord 2 rollers Ø 50 mm, 12 mm wide

Special equipment: Wicket door (outward opening), specify type of handing. Garage door drive, radio control with handheld

transmitter, key holder Lock set for vertical locking with electric drive

(vertical locking for version with wicket door) Lock set for horizontal locking with electric drive – retrofit kit Header casing max. 500 mm (same as door leaf) Third lock

Ordering size/ Modular dim. width x height

Clear passage size width x height

Standard sizes: Ordering size: from 1750 x 1875 up to 2750 x 2500/ 3000 x 2375 mm

2250 x 1920 2000 2075 2125 2375 x 1920 2000 2075 2125 2250 2375 2500 x 1920 2000 2075 2125 2250 2375 2500 2625 x 2125 2750 x 2000 2125 3000 x 2000 2125

2115 x 1785 1865 1940 1990 2245 x 1785 1865 1940 1990 2115 2240 2365 x 1785 1865 1940 1990 2115 2240 2365 2490 x 1990 2615 x 1865 1990 2865 x 1865 1990

Position No. of pieces

Item Unit price €

Total price €

Ready-to-install up-and-over garage door DL. Single-leaf element. Type of handing: behind the opening. Door leaf filling: galvanized, vertically ribbed sheet steel, powder coated similar to RAL 9016 (Traffic white). 3-sided galvanized block frame with ceiling guide rail. Lateral lever arms with 3-fold spring system and finger pinch protection. Lateral plastic cover strips. Lateral locking with special plastic catches. Special lock with profile half cylinder and plastic round handle set with pull cord. 2 plastic rollers Ø 50 mm. “Teckentrup DL“ or equivalent.

6

® Up-and-over garage door DL

Outside

Modular dimension + 20 mm (Insertion depth)

Cle

ar fi

nish

ed d

imen

sion

Screed

Installation behind the opening

Ove

rall

fram

e di

men

sion

Overall frame dimension

Cle

ar fi

nish

ed d

imen

sion

Clear finished dimension Clear finished dimension

Cle

ar fi

nish

ed d

imen

sion

Inside

Inside

Inside

Inside

Installation in the opening

Ove

rall

fram

e di

men

sion

Mod

ular

dim

ensi

on

Modular dimension

Modular dimension

Steel, ribbed, galvanised,powder coated and prime coated

Steel, galvanisedpanel powder coated and prime coated

Steel, horizontally ribbed, galvanised powder coated and prime coated

Steel, galvanised panel (Georgian/cassette) powder coated and prime coated

Wood filling Norway spruce

Subject to technical changes.

UFLFFL

UFLFFL

UFLFFL


® Up-and-over garage door DF


Technical data

Product: Up-and-over garage door DF

Installation in: Masonry Concrete Dimensions: Width: max. 3750 mm or 5000 mm

Height: max. 2750 mm, depending on the door width (see price list table)

Handing: Pre-assembled up-and-over garage door for

handing behind or in the opening. Door leaf: Door leaf frame: 4-sided galvanized special hollow profile 75 x 36 x 2 mm Reinforcement: 2 reinforcements, 2.5 mm thick Ribbed door: galvanized sheet steel, vertically ribbed, optionally horizontally ribbed or infill provided by the customer Panelled door (Georgian/cassette) made of galvanized thin sheet. Panelled door: galvanized sheet steel, 1 mm thick. Wooden door: vertical Norway spruce, optionally horizontal or fishbone, door leaf frame without plinth

Special equipment: filling - steel panels with ventilation openings, corrugated grille, horizontal spruce panels, wooden fishbone panels with mullion Door leaf thickness: 75 mm

Frame: Corner frame with L-shaped profile at the side and Z-shaped profile at the top. With galvanized lower threshold bracket 40 x 3. 6 wall anchor plugs on each side and 3 x at the top.

3 threshold anchors.

Special equipment: U-shaped frame (block frame)

Surface: Ribbed/Panelled door: powder coated Traffic white, similar to RAL 9016 Panelled door (Georgian/cassette) woodgrain, powder coated Traffic white, similar to RAL 9016 Special coating for ribbed and panelled doors: trend colours RAL of your choice

(Avoid dark colours for doors subject to direct sunlight, since cracks and warpage of the door leaf cannot be completely prevented. Pearl- effect, fluorescent and metallic colours are only possible after individual clarification.)

Wooden door: vertical Norway spruce, optionally horizontal or fishbone. Door leaf frame without plinth, powder coated Sepia brown (RAL 8014). The wood has been factory protected against fungal decay, decay and wood pests with a colourless impregnating solution. Final treatment is carried out by the customer with a final protective coat.

Fittings: 1 downward locking special lock 1 profile half cylinder 30.5 + 10 mm Plastic round handle, black 1 pull cord 2 rollers, rubber coated

Special equipment: Wicket door (outward opening), specify type of handing Garage door drive, radio control with hand-held

transmitter and key holder Lock set for vertical locking mechanism with

electric drive (vertical locking mechanism for version with wicket door

Vertical bars

Standard sizes:

Ordering dimensions

Installation behind the opening

Installation in the opening

Modular dimensions

width x height

L-shaped frame

clear opening dimensions

width x height

U-shaped frame

clear opening dimensions

width x height

U-shaped frameclear opening dimensions

width x height

4000 x 2000 2125

4500 x 2000 2125 2250

5000 x 2000 2125

3700 x 1770 1890 4200 x 1770 1890 2020 4700 x 1770 1890

3700 x 1800 3700 x 1920 4200 x 1800 4200 x 1920 4200 x 2050 4700 x 1800 4700 x 1920

3580 x 1755 3580 x 1880 4080 x 1755 4080 x 1880 4080 x 2005 4580 x 1755 4580 x 1880

Special sizes: from 3000 x 2375 mm to 3750 x 2750 mm or 5000 x 2250 mm


Item Unit price €

Total price €

Up-and-over garage door DF single-leaf element.Type of handing: Behind the opening. Door leaf filled with vertically ribbed galvanized sheet steel. Powder coated, similar to RAL 9016 (Traffic white). Corner frame with L-shaped pro-file at the side and Z-shaped profile at the top. With galvanized lower threshold profile 40 x 3. 6 wall anchor plugs on each side. Multiple spring system, plastic support. Door fittings: Spring-loaded special lock with downward locking profile half cylinder, black plastic round handle with pull cord. 2 rollers, rubber coated. “Teckentrup DF“ or equivalent.

8

® Up-and-over garage door DF

Anc

hor

dist

ance

s

For widths greater than 4 mm two additional anchors at the top and bottom

Side view in half opened position

Behind the opening L-shaped frame

Behind the opening U-shaped frame

In the openingU-shaped frame

Clear finished dimension

Cle

ar fi

nish

ed d

imen

sion

Cle

ar fi

nish

ed d

imen

sion

Cle

ar fi

nish

ed d

imen

sion




Ove

rall

fram

e di

men

sion

Ove

rall

fram

e di

men

sion

Ove

rall

fram

e di

men

sion



Modular dimension Modular dimension

Mod

ular

dim

ensi

on

Mod

ular

dim

ensi

on

Anchor assembly Anchor assembly Anchor assemblyPlug assembly Plug assembly Plug assembly

Steel, ribbed, galvanised, powder coated and prime coated

Steel, galvanisedpanel powder coated and prime coated

Steel, horizontally ribbed, galvanised powder coated and prime coated

Steel, galvanised panel (Georgian/cassette) powder coated and prime coated

Wood filling Norway spruce


FFL

FFL FFLFFL


® Single-skinned garage door ew-1 left/right handed


Technical data

Product: garage door ew-1 Installation in: Masonry Concrete Dimensions: modular dimension-width: 875 - 1250 mm modular dimension-height: 1875 - 2375 mm Handing: Single leaf garage side door. Door can be used

DIN left or DIN right, inward and outward opening. Door leaf: Leaf frame made of special hollow profiles 50 mm

thick with flange for holding the infills. Two rear reinforcement elements.

Door leaf filled with vertically ribbed galvanized sheet steel, optionally horizontally ribbed sheet steel, cassette

Wooden filling - type of wood: vertically arranged Norway spruce, optionally horizontal or diagonal, door leaf frame without plinth

Special equipment – filling: corrugated grille,

perforated sheet Ø10x14

Door leaf thickness: 50 mm Frame: Corner frame 1.5 mm thick galvanized and

powder coated similar to RAL 9016 (Traffic white), with seal. With three welded-on wall anchor plugs on each side.

Special equipment: block frame Surface: Door leaf frame/door leaf filling powder coated

similar to RAL 9016 (Traffic white), Other RAL colours at an additional charge. Door leaf filled with panels with woodgrain design surface.

Fittings: Special hinges due to re-screwing of the

hinges, optionally inward or outward opening. Special lock prepared for profile cylinder with latch lever, can be used left/right, black round handle set (plastic)

Special equipment: Profile cylinder (same closing as the up-and-

over door type) 30.5 + 30.5 mm

Standard sizes: Special sizes: up to 1250 x 2375 mm


Item Unit price €

Total price €

Single-skinned garage door ew-1. Single-leaf element which can used left/right handed. Out-side type of handing. Door leaf made of gal-vanized hollow profiles, 50 mm thick, 4-sided, with flange for holding the infill. Door leaf with vertically ribbed steel sheet panels and galvanized and powder coated corner frame, similar to RAL 9016 (Traffic white). Corner frame, 4-sided. Special lock with latch lever, prepared for profile cylinder. Black round handle set. 2 two-piece special hinges “ew-1” or comparable.

Ordering dimensions (modular dimensions)

width x height


with buffer without buffer 875 x 1875 2000 2125 1000 x 2000 2125

809 x 1805 1930 2055 934 x 1930 2055

809 x 1835 1960 2085 934 x 1960 2085

Two-piece hinge

Two-piece hinge

Mod

ular

dim

ensi

on

Modular dimensionM

odul

ar d

imen

sion

Mod

ular

dim

ensi

on

Cle

ar p

assa

ge s

ize

Clear passage size

Cle

ar p

assa

ge s

ize

Cle

ar p

assa

ge s

ize

Out

side

Outside

Out

side

Out

side

Outer buffer Inner buffer modular dimension height -55 mm

Without bottom bufferdimension height -30 mm

DIN left shown,DIN right laterally reversed

Block frame Plug assemblyVersion 1

Plug assemblyVersion 2

Wall anchor assembly

Steel vertically ribbed Steel panels Steel horizontally ribbed

Steel panel (Georgian/cassette)

Wood filling:Norway spruce vertical,Norway spruce horizontal,Norway spruce diagonal

Door leaf versions

10

FFL FFL


Single-skinned garage door ew-1®


® Single-skinned garage door ew-2


Technical data

Product: Garage door ew-2 Installation in: Masonry Concrete Dimensions: modular dimension-width: 1350 - 2500 mm modular dimension-height: 1750 - 2250 mm Handing: DIN left outside/inside DIN right outside/inside Door leaf: Leaf frame made of special hollow profiles 50 mm thick with flange for holding the infill. Two rear reinforcement elements.

Door leaf filled with vertically ribbed galvanized sheet steel, optionally horizontally ribbed, sheet steel

Special equipment – filling: corrugated grille, perforated sheet Ø10x14

Door leaf thickness: 50 mm Frame: Corner frame 2 mm thick, galvanized and

powder coated similar to RAL 9016 (Traffic white), with seal. With three welded-on wall anchor plugs on each side.

Special equipment: block frame Surface: Door leaf frame/door leaf filling powder coated

similar to RAL 9016 (Traffic white). Other RAL colours at an additional charge. Door leaf filled with panels with woodgrain design surface.

Fittings: 4 special hinges Special lock prepared for profile cylinder with latch lever, can be used left/right, black round handle set, (plastic) With 2 door leaf fixing devices at the header and two security bolts on each side

Special equipment: Profile cylinder (same closing as the up-and-over door type) 30.5 + 30.5 mm Standard sizes:

Ordering dimensions

(modular dimensions)

width x height


with buffer without buffer

2000 x 2000 2125 2250 x 2250 2500 x 2125

1934 x 1930 2055 2184 x 2180 2434 x 2055

1934 x 1930 2055 2184 x 2180 2434 x 2055

Special sizes: from 1350 x 1750 to 2500 x 2250 mm


Item Unit price €

Total price €

Single-skinned garage door ew-2. Double-leaf element. Outside type of handing. Door leaf frame made of special hollow profiles 50 mm thick with flange for holding the infill. Two rear reinforcement elements. Door leaf with vertically ribbed sheet steel panels and galvanized and powder coated corner frame, similar to RAL 9016 (Traffic white). Corner frame, 4-sided. Special lock with latch lever, prepared for profile cylinder. Black round handle set (plastic). 4 two-piece special hinges “ew-2” or equivalent.

12

Single-skinned garage door ew-2

Two-piece hinge

Two-piece hinge

Mod

ular

dim

ensi

on

Modular dimension

Mod

ular

dim

ensi

on

Mod

ular

dim

ensi

on

Cle

ar o

peni

ng

Clear opening

Cle

ar o

peni

ng

Cle

ar o

peni

ng

Outside

Outer buffer Inner buffer modular dimension height -55 mm

Without bottom bufferdimension height -30 mm

Out

side

Out

side

Out

side

Active door leaf DIN left shown,active door leaf DIN right laterally reversed

Block frame Plug assemblyVersion 1

Plug assemblyVersion 2

Wall anchor assembly

Steel vertically ribbed Steel panels Steel panel (Georgian/cassette)


Door leaf versions

FFLFFL

®


® Single-skinned garage door RP-1


Technical data

Product: Garage door RP-1 Installation in: Masonry Concrete Dimensions: width: 750 - 1350 mm height: 1750 - 2500 mm Handing: DIN left outside/inside DIN right outside/inside Door leaf: Door leaf frame made of RP tube or special

tubing with flange for holding the infill.

Door leaf filled with ribbed, smooth or embossed galvanized sheet steel.

Special equipment: filling - embossed or smooth sheet steel panels or wooden filling Door leaf thickness: 40 mm Frame: Corner frame 2 mm thick galvanized and

powder coated similar to RAL 9016 (Traffic white) or similar to RAL 8014 (Sepia brown). With 3-sided seal. 3 wall anchor plugs on each side

Special equipment: Block frame Surface: Door leaf frame/Door leaf filling powder coated

similar to RAL 9016 (Traffic white) or RAL 8014 (Sepia brown). Other RAL colours at an additional charge.

Fittings: With tubular frame-mortice lock, prepared

for profile cylinder, round handle set with rose escutcheon.

2 two-piece KO hinges with ball bearings Special equipment: Profile cylinder 30.5 + 30.5 mm Glazing Ventilation slats Corrugated grille filling Bars Mullions (to partition the fields) Galvanized door leaf frame and frame Adjustable hinges Special sizes:

Ordering dimensions

(modular dimensions)

width x height

Clear passage sizes width x height


from 750 x 1750 to 1000 x 2000 to 1125 x 2250 to 1350 x 2500

from 680 x 1685 to 930 x 2000 to 1055 x 2185 to 1280 x 2435

from 680 x 1715 to 930 x 1965 to 1055 x 2215 to 1280 x 2465


Item Unit price €

Total price €

Single-skinned steel door RP-1. Single-leaf element, outside handing. Door leaf frame made of RP tube (4-sided) with flange for holding the panels. Door leaf thickness 40 mm. Door leaf filled with ribbed sheet steel, galvanized. 3-sided angular frame, powder coated, similar to RAL 9016 (Traffic white). Mortice lock prepared for profile cylinder. Black plastic handle set, 2 two-piece special hinges. “RP-1” or equivalent.

Mod

ular

dim

ensi

on

Modular dimension

Mod

ular

dim

ensi

on

Cle

ar o

peni

ng

Clear opening

Cle

ar o

peni

ng

Mod

ular

dim

ensi

on

Cle

ar o

peni

ng

Outside

Outside

Outside Outside

Inner buffer ventilation slats

Outer buffer Inner buffer modular

DIN left shown,DIN right laterally reversed

Two-piece hinge

Two-piece hinge

Plug assembly Wall anchor assembly in accordance with DIN 18093

Weld-on assembly

Ribbed doorWooden door

Panel filling Ventilation slats Corrugated grille

Door leaf versions

FFL FFL FFL


Single-skinned garage door RP-1 ®

14


® Single-skinned garage door RP-2


Technical data

Product: Garage door RP-2 Installation in: Masonry Concrete Dimensions: width: 1500 – 3000 mm height: 1750 – 3000 mm Handing: active door leaf DIN left outside/inside active door leaf DIN right outside/inside Door leaf: Door leaf frame made of RP tube or special

tubing with flange for holding the infill.

Door leaf filled with ribbed, smooth or embossed galvanized sheet steel.

Special equipment: filling - sheet steel panels, corrugated grille or wooden filling Door leaf thickness: 40 mm Frame: Corner frame 2 mm thick galvanized and

powder coated similar to RAL 9016 (Traffic white). With 3-sided seal.

Surface: Door leaf frame/Door leaf filling powder coated

similar to RAL 9016 (Traffic white). Other RAL colours at an additional charge.

Fittings: (Active door leaf) with tubular frame-mortice

lock, prepared for profile cylinder, round handle set with rose escutcheon.

Inactive door leaf with mounted sliding bolt, on the opposite hinge side (outer buffer - on the hinge side for inner buffer) 4 two-piece KO hinges with ball bearings up to

a modular dimension height of 2500 mm. 6 two-piece KO hinges with ball bearings up to a modular dimension height of 2500 mm.

Special equipment: Profile cylinder 30.5 + 30.5 mm Glazing Ventilation blind Corrugated grille filling Bars (as a yard gate) Mullions (to partition the fields) Galvanized door leaf frame and frame Special sizes:

Ordering dimensions(modular

dimensions) width x height



from 1500 x 1750 to 2000 x 2000 2500 3000 to 2375 x 2000 2500 3000 to 2750 x 2000 2500 3000 to 3000 x 2000 2500 3000




Item Unit price €

Total price €

Single-skinned steel door RP-2. Double-leaf element, outside handing. Active door leaf DIN right. Door leaf 40 mm thick, made of galvanized RP profiles (4-sided). Door leaf filled with ribbed sheet steel, galvanized. 3-sided angular frame, powder coated, similar to RAL 9016 (Traffic white). Active door leaf with mortice lock pre-pared for profile cylinder. Black plastic handle set. Inactive door leaf with sliding bolt on the opposite hinge side. 2 two-piece special hinges. “RP-2” or equivalent.

Two-piece hinge

Two-piece hinge

Mod

ular

dim

ensi

on

Mod

ular

dim

ensi

on

Cle

ar o

peni

ng

Cle

ar o

peni

ng

Mod

ular

dim

ensi

on

Cle

ar o

peni

ng

Outside Outside Outside

Inner buffer ventilation slats

Outer buffer Inner buffer modular

Modular dimension

Clear opening

Active door leaf DIN left shown,Active door leaf DIN right laterally reversed

Plug assembly Wall anchor assembly in accordance with DIN 18093

Weld-on assembly

Ribbed doorWooden door

Panel filling Ventilation slats Corrugated grille

Door leaf versions

FFL FFL FFL


Single-skinned garage door RP-2 ®

16


®

Centre ribbed:GSW 40-S

Sectional door GSW 40-S Double-skinned steel door panels 40 mm

Text example Compile and tender according to requirements. Please refer to technical data below for respective details Updated 1st June 2015

Technical data

Product: Garage sectional door GSW 40-S

Heat insulation U-value: 0.56 W/m²k (40 mm panel) 0.95 W/m²k (only door leaf) 1.48 W/m²k (complete door, door surface 10 m²)

Installation in: Masonry Concrete Autoclaved aerated concrete Wooden framework

Dimensions: GSW 40-S: only standard sizes, see price list

Type of handing: Behind the soffit

Door leaf: Door leaf made of individual double-skinned door sections including central seal with the same partitioning, galvanized sheet steel. Finger pinch protection inside and outside in acc. with DIN EN 12604. Building depth of the sections 40 mm

Insulation: Polyurethane foam core.

Surface: Outside: woodgrain design, colour Traffic white similar to RAL 9016. Inside: stucco design, galvanized with transparent protective film. Bottom door edge: Frost-proof and rot-proof EPDM floor seal

Fittings: Standard version: Default without manual locking mechanism Prepared for emergency release (required if

there is no other entry to the garage) Special version:

With manual locking mechanism

Frame: Profile frame with header trim made of sendzimir galvanized sheet steel, EPDM strip with sealing lip at the sides and header trim. Coil-coated with polyester, prime coated Traffic white similar to

RAL 9016.

Locking: On request with automatic, double-sided engaging special lock. Round handle set and profile cylinder for manual operation.

Handle at the bottom profile. Weight com-

pensation: Via a multiple tension spring/double cable system housed in a micro-profiled spring duct above the horizontal guide rail.

Surface Basic coat on door outer surface, double coat Protection: on the outside (polyester-based 25 µm). Galvanized steel parts, galvanized springs.

Drive: Microprocessor-controlled drive, rail-guided, 230 V, 50 Hz Control: Impulse control with self- programming

force limiter Soft start and stop Digital remote control Can be extended with other control units


Item Unit price €

Total price €

Garage sectional door GSW 40-S, door leaf consisting of double-skinned steel door panels, galvanized surface, PUR foam core. Building depth 40 mm, outside woodgrain, inside stucco design. Outer colour Traffic white similar to RAL 9016, inside galvanized with transparent protec-tive film. Door sections with central seal and floor seal. Frame with lateral strips. All fittings made of galvanized steel, lateral guidance via maintenance-free, adjustable rollers. Weight compensation via multiple spring/double cable system, tension springs housed in a spring duct above the horizontal guide rails. “CarTeck GSW 40-S” or equivalent.

195 17

0

170

500

800

140

82,5 82,5

S

170

500

S

140

375

140

495

*75

Dimensions for 145 mm and 265 mm header versions on request

For the depth see table “Building depth with drive”

For the depth see table “Building depth without drive”

Standard for manual operation120 mm Headroom 240 mm HeadroomStandard with drive

240Header120Header

Ord

erin

g di

men

sion

= H

= c

lear

hei

ght

inside

inside

* 240 mm Headroom =150 mm in the round handle set (middle)

Ord

erin

g di

men

sion

= H

= c

lear

hei

ght

Min. inner garage dimension = ordering dimension + 165

BOrdering dimension = = clear width

Please observe the following measurement details to guarantee exact assembly and precise and reliable operation of the CarTeck sectional door.

S

120 mm

240 mm - 25 mm

120 mm

120 mm

240 mm

- 150 mm

- 80 mm

S

H

B clear opening width (= ordering dimension)

clear height (= ordering dimension)

Equipment:Required headroom: Clear opening height:

with driveManual operation

completely free Standard version

Manual operationManual operationwith drive completely free

The required headroom increases by + 25 mm for doors with reinforced roller retainers

Standard versionSpecial versionSpecial version with door stopper (see accessories GSW doors)

Special version with pack – 125 mm extended top roller retainers (see accessories GSW doors)

27,5

40

140

82,5frame

door leaf

section Frame

Sectional door GSW 40-S ®

18

Double-skinned steel door panels 40 mm



®

ribbed cassette unribbed centre ribbed

Sectional door GSW 40-L Double-skinned steel door panels 40 mm optionally with glazing, optionally with wicket door Text example Compile and tender to requirements. Please refer to technical data below for respective details. Updated 1st June 2015

Technical data Product: Garage sectional door GSW 40-L

Heat insulation U-value: 0.56 W/m²k (40 mm panel) 0.95 W/m²k (only door leaf) 1.48 W/m²k (complete door, door surface 10 m²)

Installation in: Masonry Concrete Autoclaved aerated concrete Wooden framework

Dimensions: width: 2000 – 5500 mm height: 1875 – 3000 mm

Handing: Behind the soffit

Door leaf: Door leaf made of individual double-skinned door sections including central seal with the same partitioning, galvanized sheet steel, building depth of the sections 40 mm. Insulation: polyurethane foam core finger pinch protection inside and outside in accordance with DIN EN 12604

Surface: Outer surface woodgrain design, stucco design, smooth or micro-profiled, Traffic white similar to RAL 9016 Inside stucco design, Grey white similar to RAL 9002

Bottom door edge: Frost-proof and rot-proof EPDM floor seal

Fittings: Standard version: Without manual locking mechanism Prepared for emergency release (required if there is no other entry to the garage) Special version: with manual locking mechanism

(up to door width of 5000 mm).

Wicket door: Enclosed in aluminium profiles E6/EV1 (the wicket door is always located in the middle), with low threshold 45 mm and full floor seal. The wicket door has a standard clearance width of 810 mm. All wicket doors include a top door closer, a profile cylinder pre-equipped lock with profile cylinder and aluminium handle set in E6/EV1.

Frame: Profile frame made of sendzimir galvanized sheet steel, coil-coated with polyester, prime coated Traffic white similar to RAL 9016,

optionally in trend and RAL colour at additional charge. EPDM strip with sealing lip at the sides. Header trim default in trend colour, RAL colour or similar to wood design.

Locking: With manual locking mechanism (up to door width

of 5000 mm).

Weight com- Via multiple tension spring/double cable system pensation: housed in a micro-profiled spring duct above the horizontal guide rail.

Surface Steel: coil-coated, double coat on the outside protection: (polyester based 25 m)

Wood designs: steel sections with UV-resistant, thermoplastic surface film in attractive designs. Single coat on the inside (polyester based 10 m). Galvanized steel parts, galvanized springs.

Special equipment: additionally prime coated in trend colour or RAL of your choice. Pearl-effect, fluorescent and metallic colours are only possible after individual clarification.

Drive: Microprocessor-controlled drive, rail-guided, 230 V, 50 Hz

Control: impulse control with self-programming of the force limiter, soft start and stop Digital remote control, extendable with other control units

Glazing: Glazed strip or aluminium profiles, anodized, across the entire width of the door (separate

section), plastic double glazing 20 mm, clear or crystal structure. Glazing strip with seals. Other colours or powder coating in accordance with RAL possible. Glazing for panelled, ribbed, centre ribbed,

unribbed door (white polyurethane frame with wooden structure) in various versions (see dealer price list). Glazing: plastic double glazing 20 mm clear or crystal structure on the inside.

Only possible for GSW 40-L unribbed / unribbed- smooth: Stainless steel round glazing Ø 305 mm.

One pane of ESG glazing colourless and clear. Stainless steel filling plates.

Type round glazing, plastic Ø 315 mm. Type Rectangular 3, white plastic glazing frame. Type 1/2 square, white polyurethane frame with

smooth surface.

Glazing: plastic double glazing 20 mm clear, structured or satin.


Item Unit price €

Total price €

Garage sectional door, door leaf consisting of individual double-skinned steel door panels, galvanized surface, PUR foam core. Building depth 40 mm, outer surface woodgrain, inner surface stucco design. Outer colour Traffic white similar to RAL 9016, inner colour Grey white similar to RAL 9002. Door sections with central seal and floor seal. Frame with lateral strips. All fittings made of galvanized steel, lateral guidance via maintenance-free, adjustable rollers. Weight compensation via multiple spring/double cable system, tension springs housed in a spring duct above the horizontal guide rails. “CarTeck GSW 40-L” or equivalent.

195 17

0

170

500

800

140

82,5 82,5

S

170

500

S

140

375

140

495

*75

Dimensions for 145 mm and 265 mm header versions on request

For the depth see table “Building depth with drive”

For the depth see table “Building depth without drive”

Standard for manual operation120 mm Headroom 240 mm HeadroomStandard with drive

240Header120Header

Ord

erin

g di

men

sion

= H

= c

lear

hei

ght

inside

inside

* 240 mm Headroom =150 mm in the round handle set (middle)

Ord

erin

g di

men

sion

= H

= c

lear

hei

ght

Min. inner garage dimension = ordering dimension + 165

BOrdering dimension = = clear width

Please observe the following measurement details to guarantee exact assembly and precise and reliable operation of the CarTeck sectional door.

S

120 mm

240 mm - 25 mm

120 mm

120 mm

240 mm

- 150 mm

- 80 mm

S

H

B clear opening width (= ordering dimension)

clear height (= ordering dimension)

Equipment:Required headroom: Clear opening height:

with driveManual operation

completely free Standard version

Manual operationManual operationwith drive completely free

The required headroom increases by + 25 mm for doors with reinforced roller retainers

Standard versionSpecial versionSpecial version with door stopper (see accessories GSW doors)

Special version with pack – 125 mm extended top roller retainers (see accessories GSW doors)


27.5

40

140

82.5frame

door leaf

section Frame

Sectional door GSW 40-L ®

20

Double-skinned steel door panels 40 mmoptionally with glazing, optionally with wicket door


® Sectional door GSH Wooden frame construction


Technical data

Product: Garage sectional door GSH Installation in: Masonry Concrete Autoclaved aerated concrete Wooden framework Dimensions: width: 2000 – 5000 mm height: 1875 – 3000 mm smaller dimensions on request Type of handing: Behind the soffit Door leaf: Consisting of separate door sections made of

first choice wood, including central seal. Native spruce/Fir and hemlock are processed with a natural look. Building depth of the sections is 40 mm.

ribbed cassette unribbed

fishbone type 1 fishbone type 2

Bottom door edge: Frost-proof and rot-proof EPDM floor seal Fittings (Standard version): With special connecting console for rail-guided

drives. We recommend rail-guided drives when

operating GSH doors. The doors are not supplied as manually operated doors.

Standard GSH doors are not supplied with apparatus for emergency release.

All fittings made of galvanized steel Laterally adjustable rollers due to patented eccentric roller retainer, maintenance free.

Frame: Profile frame made of sendzimir galvanized

sheet steel, coil-coated with polyester basic coating in Traffic white similar to RAL 9016. Optionally in trend and RAL colours

at additional charge. EPDM strip with sealing lip at the sides and header trim. Weight compensation: Via a multiple tension spring/double cable

system housed in a micro-profiled spring duct above the horizontal guide rail.

Surface protection: The wood has been factory protected against fungal decay, decay and wood pests with a

colourless impregnating solution. The door leaf coated with colourless impregnating solution ex works must be treated with a final protective coat 2 - 3 weeks after installation.

Or painted All steel parts and springs are galvanized

Drive: Microprocessor-controlled drive, rail-guided, 230 V, 50 Hz Control: impulse control with self-programming force limiter. Soft start and stop Digital remote control, extendable with other control units


Item Unit price €

Total price €

Garage sectional door, consisting of separate door sections made of first choice wood, including central seal. Native spruce/Fir with a natural look. With central seal and floor seal. Frame with lateral strips. All fittings made of galvanized steel, lateral guidance via maintenance-free, adjustable rollers. Weight compensation via multiple spring/double cable system, tension springs housed in a spring duct above the horizontal guide rails. “CarTeck GSH“ or equivalent.

standard versionSpecial version with pack – 125 mm extended top roller retainers (see accessories GSW doors)

Wooden frame construction

120

120

120

Sectional door GSH®

22 Subject to technical changes.


®

- ribbed woodgrain stucco smooth micro-prof.

- unribbed woodgrain stucco smooth micro-prof.

- centre ribbed woodgrain stucco smooth micro-prof.- wood design smooth

- cassette woodgrain- wood design woodgrain

Side doors garage sectional door outer surfaces to match GSW 40-L


Technical data

Product: Side doors for GSW 40-L

Installation in: Masonry Concrete Autoclaved aerated concrete Steel construction Wooden framework

Dimensions: width: 875 - 1400 mm single-Leaf height: 1925 - 2550 mm other sizes available on request

Dimensions: width: 1400 - 2500 mm double-Leaf height: 1925 - 2300 mm other sizes available on request

Type of handing: Please always specify when ordering: - Behind the opening/inward opening - In the opening/inward opening - In the opening/outward opening

Door leaf: Appearance matches CarTeck garage sectional door GSW 40-L, door leaf frame and frame made of

extruded aluminium profiles (no thermal separation), building depth 53 mm, 3-sided double rabbet seal. Sliding threshold seal. Door filling made of double-skinned steel panels, outside woodgrain, inside

stucco design, made of galvanized sheet steel, PU foam core. Alignment of door panels, ribs/panels

only possible with doors of the same height.

Surface: Outer surface woodgrain design Outside woodgrain design Inside stucco design Seals: Frost-proof EPDM bottom sliding seal

Door frame: Made of extruded aluminium profiles, mitred at the top on both sides. Building depth 53 mm, bottom threshold 4 mm (can be removed if required).

Fittings and locks: Mortice lock with profile cylinder Plastic handle set, profile cylinder version Adjustable hinges Surface protection: Door filling:

Door panels made of galvanized sheet steel with polyurethane basic coating on both sides. outside: - Standard Traffic white similar to RAL 9016, trend colours or RAL of your choice, similar to the RAL colour chart. Version GSW 40-L "Golden Oak", "Rosewood", "Winchester". Steel sections with UV-resistant, thermoplastic surface film in attract-tive designs. inside: - Grey white, similar to RAL 9002 Safety notes: (Avoid dark colours for doors subject to direct sun-light, since cracks and warpage of the door leaf cannot be completely prevented). Not available in pearl-effect, fluorescent and metallic colours.

Glazing: Glazed strip or aluminium profiles, anodized, across the entire width of the door (separate section), plastic double glazing 20 mm, clear, opal or crystal structure. Glazing strip with seals. Other colours or powder coating in accordance with RAL possible. Glazing for cassette, ribbed, centre ribbed,

unribbed door (white polyurethane frame with smooth surface) in various versions (see price list). Glazing: plastic double glazing 20 mm, clear,

crystal structure or satin on the inside. Cassette Pure

Only for GSW 40-L unribbed/unribbed-smooth Stainless steel round glazing Ø 305 mm.

One pane of ESG glazing colourless and clear. Stainless steel filling plates.

Type round glazing, plastic, Ø 315 mm. Type Rectangular 3, white plastic glazing frame Type 1/2 square, white polyurethane frame with

wood structure Glazing: plastic double glazing 20 mm, clear, structured or satin.


Item Unit price €

Total price €

Garage side door, matches garage sectional door GSW 40-L, door leaf frame and door frame made of extruded aluminium profiles (no thermal separation), building depth 53 mm, 3-sided double rabbet seal, sliding threshold seal. Door filling made of double-skinned steel door panels, outside woodgrain, inside stucco design, made of galvanized sheet steel, PU foam core. “CarTeck side door type GSW 40-L” or equivalent.

Side doors garage sectional door outer surfaces to match GSW 40-L

Structural opening + 100 mm = RAM

Structural opening + 100 mm = RAM

Structural opening

Structural opening – 40 mm = clear opening width


Str

uctu

ral o

peni

ng +

50

mm

= R

AM

Str

uctu

ral o

peni

ng

Str

uctu

ral o

peni

ng –

20

mm

= c

lear

ope

ning

wid

th

Str

uctu

ral o

peni

ng -

10

mm

= R

AM

Str

uctu

ral o

peni

ng

Str

uctu

ral o

peni

ng –

80

mm

= c

lear

ope

ning

wid

th

Structural opening - 10 mm = RAM

Structural opening - 10 mm = RAM

Structural opening

Structural opening



Note: Overall frame dimension (RAM) = Ordering dimension

Installation behind the soffitonly inward opening

Installation behind the soffit only inward opening

Installation in thesoffit

inward andoutward opening

Installation in the soffit inward and outward opening

Structural opening

Door height

Height ofthe sections

Dimension X(handle)

2500 mm2375 mm2250 mm2125 mm2000 mm1875 mm

493 mm

469 mm

556 mm

523 mm

493 mm

469 mm

935 mm

1140 mm

1035 mm

985 mm

935 mm

1140 mm

DIN left shown,,DIN right laterally reversed

Active door leaf DIN left shown, Active door leaf DIN right laterally reversed

®

24 Subject to technical changes.


® Side door garage sectional door GSH


Technical data

Product: Side door garage sectional door GSH Installation in: Masonry Concrete Autoclaved aerated concrete Steel construction Ordering dimensions: width: 908 - 1400 mm height: 1925 - 2400 mm Type of handing: Please always specify when ordering: - behind the opening/inward opening - in the opening/inward opening - in the opening/outward opening Door leaf: Matches CarTeck garage sectional door GSH. Door leaf, filling and door frame made of

Native spruce/Fir, hemlock, with waterproof bonding. Building depth 68 mm, 3-sided, double rabbet seal and bottom threshold seal. Alignment of the door filling to the door leaf is only possible for a door of the same height.

ribbed cassette fishbone fishbone type 1 type 2 Bottom door edge: Frost-proof EPDM bottom threshold seal Fittings and closing devices: Mortice lock with profile cylinder Plastic handle set, profile cylinder version Adjustable hinges

Surface protection: The wood has been factory protected against

fungal decay, decay and wood pests with a colourless impregnating solution. Surface optionally coated with an open-porous paint or RAL of your choice.

Optionally: basic coat of coloured paint (always adhere to the instructions regarding the required final treatment provided by the customer) Or final treatment


Item Unit price €

Total price €

Garage side door, matches CarTeck garage sectional door GSH. Door leaf, filling and door frame made of Native spruce/Fir, with waterproof bonding. Building depth 68 mm, 3-sided double rabbet seal and bottom threshold seal. Alignment of the door filling is only possible for a door of the same height. “CarTeck side door GSH” or equivalent.

Side door garage sectional door GSH

RAM = structural opening + 120 mmRAM = structural opening - 10 mm

Clear opening = RRM – 40 mmClear opening = RRM – 170 mm

Structural opening (RRM)

Str

uctu

ral o

peni

ng (

RR

M)

Structural opening (RRM)

Note: Overall frame dimension (RAM) = Ordering dimension

Ove

rall

fram

e di

men

sion

= S

truc

tura

l ope

ning

+ 6

0 m

m

Ove

rall

fram

e di

men

sion

= S

truc

tura

l ope

ning

- 1

0 m

m

Cle

ar o

peni

ng =

str

uctu

ral o

peni

ng –

42

mm

Str

uctu

ral o

peni

ng (

RR

M)

Cle

ar o

peni

ng =

str

uctu

ral o

peni

ng –

112

mm

Installation behind the soffit Installation in the soffit


®

26


® Garage door drives 12.2, 20.2, 40.2

Example Compile and tender according to requirements. Please refer to technical data below for respective details Updated 1st June 2015

Technical data The garage door drive should only be used for the automatic operation of spring balanced up-and-over garage doors and sectional doors in non-commercial outdoor areas. Product: Garage door drive – drive system 12.2 Refer to latest price list for assignment table

Rated voltage 230 V (alternating current) Control voltage 24 V (direct current) *Tensile and compressive force 500 N Power consumption during stand-by < 2 W Operating speed up to 140 mm/sec Including a manipulation-proof 2-channel

hand-held transmitter 868 MHz Integrated lighting

Design depth of drive incl. rail Z1 = 3320 mm, 3170 mm at 90° rotated drive head

Product: Garage door drive – drive system 20.2 Refer to latest price list for assignment table

Rated voltage 230 V (alternating current) Control voltage 24 V (direct current) *Tensile and compressive force 1000 N Power consumption during stand-by < 2.5W Operating speed up to 200 mm/sec Including a manipulation-proof 4-channel

hand-held transmitter, 868 MHz (black) Integrated lighting

Design depth of drive incl. rail Z1 = 3320 mm, Z2 = 3570 mm

Product: Garage door drive – drive system 40.2 Refer to latest price list for assignment table

Rated voltage 230 V (alternating current) Control voltage 24 V (direct current) *Tensile and compressive force 1500 N Power consumption during stand-by <2.5W Operating speed up to 200 mm/sec Including a manipulation-proof 4-channel

hand-held transmitter, 868 MHz (black) Integrated lighting

Design depth of drive incl. rail Z1 = 3320 mm, Z2 = 3570 mm, Z3 = 4070 mm

Accessories:

Emergency unlock kit o Emergency unlock kit for sectional doors o Emergency unlock kit for up-and-over doors

Light barrier Indoor switch TI-I1, pulse Radio indoor switch TI-F2 Radio code switch, 868 MHz Key-operated switch (flush/surface mounted) Hand-held transmitter: o SH2-S 2-button hand-held transmitter,

868 MHz o SH4-D black/white 4 button hand-held

transmitter, 868 MHz o Wall bracket for SH4-D remote control

External 1-channel radio receiver with antenna Additional rail suspension

* relates to spring-compensated door leaf weight

Position Quantity Item Unit price €

Total price €

Garage door drive – drive system 20.2 Rated voltage 230 V (alternating current) Control voltage 24 V (direct current) Tensile and compressive force 1000 N Power consumption during stand-by

< 2.5 W Operating speed up to 200 mm/sec Tested burglary resistance Including a manipulation-proof hand-held

transmitter, 4-channel, 868 MHz (black) Integrated lighting

Design depth of drive incl. rail Z1 = 3320 mm Manufacturer "CarTeck drive system 20.2" or similar.

2-yearguarantee

Documents

Garage doors - Teckentrupteckentrup.co.za/.../south-africa/...garage_doors.pdf · Garage sectional doors and side doors Product Ordering dimensions width/height in mm (modular dimensions)